The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220430121902.59895-7-krzysztof.kozlowski@linaro.org
dtschema expects DMA channels in specific order (tx, rx and tx-sec).
The order actually should not matter because dma-names is used however
let's make it aligned with dtschema to suppress warnings like:
i2s@eee30000: dma-names: ['rx', 'tx', 'tx-sec'] is not valid under any of the given schemas
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Co-developed-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/CY4PR04MB056779A9C50DC95987C5272ACB1C9@CY4PR04MB0567.namprd04.prod.outlook.com
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Move USB PHYs to a standard arrays for S5PV210 EHCI/OHCI devices. This
resolves the conflict between S5PV210 EHCI/OHCI sub-nodes and generic USB
device bindings.
Suggested-by: Måns Rullgård <mans@mansr.com>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220314181948.246434-3-krzysztof.kozlowski@canonical.com
This property is relevant to consumers of io-channels. Here it is
used by a provider.
dt-schema will now report and error as this property must be in the
same node as io-channels and it is not here.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201115192951.1073632-6-jic23@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The 'audio-subsystem' node is an artificial creation, not representing
real hardware. The hardware is described by its nodes - AUDSS clock
controller and I2S0.
Remove the 'audio-subsystem' node along with its undocumented compatible
to fix dtbs_check warnings like:
audio-subsystem: $nodename:0: 'audio-subsystem' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-9-krzk@kernel.org
The Power Management Unit (PMU) is a separate device which has little
common with clock controller. Moving it to one level up (from clock
controller child to SoC) allows to remove fake simple-bus compatible and
dtbs_check warnings like:
clock-controller@e0100000: $nodename:0:
'clock-controller@e0100000' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-8-krzk@kernel.org
The fixed clocks are kept under dedicated 'external-clocks' node, thus a
fake 'reg' was added. This is not correct with dtschema as fixed-clock
binding does not have a 'reg' property. Moving fixed clocks out of
'soc' to root node fixes multiple dtbs_check warnings:
external-clocks: $nodename:0: 'external-clocks' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
external-clocks: #size-cells:0:0: 0 is not one of [1, 2]
external-clocks: oscillator@0:reg:0: [0] is too short
external-clocks: oscillator@1:reg:0: [1] is too short
external-clocks: 'ranges' is a required property
oscillator@0: 'reg' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-7-krzk@kernel.org
There is no need to keep DMA controller nodes under AMBA bus node.
Remove the "amba" node to fix dtschema warnings like:
amba: $nodename:0: 'amba' does not match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-6-krzk@kernel.org
The extended mainscaler is only available on FIMC1 and there
are minimum pixel alignments that differ from the default.
Additionally, the cam-if interface is available on all three
while FIMC2 has no rotators. The lcd-wb interface is supported
on FIMC1.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The exynos-adc driver now supports the S5PV210, so add the DT
node so that devices can use it.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The camera driver (according also to bindings) registers a clock
provider if clock-output-names property is present and later the sensors
use registered clocks.
The DTS for S5Pv210 Goni board was incorrectly adding a child node with
clock output cells but without clock-output-names property. Although
the DTS was compiling (with "/soc/camera/clock-controller: missing or
empty reg/ranges property" warning), the clock provider was not
registered.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
According to Devicetree specification, the unit-address must match the
first address specified in the reg property of the node. Fix the DTC
warning onenand node:
arch/arm/boot/dts/s5pv210.dtsi:81.29-93.5:
Warning (simple_bus_reg): /soc/onenand@b0000000: simple-bus unit address format error, expected "b0600000"
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
This commit adds DMC (Dynamic Memory Controller) nodes, which are needed
by S5Pv210 cpufreq driver to work.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Since we have separate compatible for S5Pv210 FIMD, let's use it rather
than using one from Exynos4210.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add node for Exynos Rorator device, so it can be used on all S5Pv210
based devices.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add node for s5p-jpeg codec, which is present in S5PV210 SoC.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The pin controller block of S5Pv210 for handling external wakeup
interrupts is different than in newer designs (Exynos).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <snawrocki@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:
arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. The interrupt has to be cleared, because otherwise
system enters infinite interrupt handling loop.
Use a samsung,s3c6410-wdt compatible to select appropriate quirk for
clearing the watchdog interrupt.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The compatible string "simple-bus" is well defined in ePAPR, while
I see no documentation for the "arm,amba-bus" arnywhere in ePAPR or
Documentation/devicetree/.
DT is also used by other projects than Linux kernel. It is not a
good idea to rely on such an unofficial binding.
This commit
- replaces "arm,amba-bus" with "simple-bus"
- drops "arm,amba-bus" where it is used along with "simple-bus"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add generic device tree for s5pv210 and s5pv210-pinctrl
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
