Absolute path to other DT schema is preferred over relative one.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220726115650.100726-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'reg' property is missing from the mediatek,mt7530 schema which
results in the following warning once 'unevaluatedProperties' is fixed:
Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.example.dtb: switch@0: Unevaluated properties are not allowed ('reg' was unexpected)
Fixes: e0dda31197 ("dt-bindings: net: dsa: convert binding for mediatek switches")
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220701222240.1706272-1-robh@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Describe the switch interrupts (dlr, switch, prp, hub, pattern) which
are connected to the GIC.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation in .yaml format and updates to the MAINTAINERS
Also 'make dt_binding_check' is passed.
RGMII internal delay values for the mac is retrieved from
rx-internal-delay-ps & tx-internal-delay-ps as per the feedback from
v3 patch series.
https://lore.kernel.org/netdev/20210802121550.gqgbipqdvp5x76ii@skbuf/
It supports only the delay value of 0ns and 2ns.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add bindings for Renesas RZ/N1 Advanced 5 port switch. This switch is
present on Renesas RZ/N1 SoC and was probably provided by MoreThanIP.
This company does not exists anymore and has been bought by Synopsys.
Since this IP can't be find anymore in the Synospsy portfolio, lets use
Renesas as the vendor compatible for this IP.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A board may have no independent reset-line, so reset cannot be used
inside switch driver.
E.g. on Bananapi-R2 Pro switch and gmac are connected to same reset-line.
Resets should be acquired only to 1 device/driver. This prevents reset to
be bound to switch-driver if reset is already used for gmac. If reset is
only used by switch driver it resets the switch *and* the gmac after the
mdio bus comes up resulting in mdio bus goes down. It takes some time
until all is up again, switch driver tries to read from mdio, will fail
and defer the probe. On next try the reset does the same again.
Make reset optional for such boards.
Allow port 5 as cpu-port and phy-mode rgmii for mt7531.
- MT7530 supports RGMII on port 5 and RGMII/TRGMII on port 6.
- MT7531 supports on port 5 RGMII and SGMII (dual-sgmii) and
SGMII on port 6.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert txt binding to yaml binding for Mediatek switches.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
SPI peripheral device bindings need to reference spi-peripheral-props.yaml
in order to use various SPI controller specific properties. Otherwise,
the unevaluatedProperties check will reject any controller specific
properties.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220531220122.2412711-1-robh@kernel.org
Compatible strings are used to help the driver find the chip ID/version
register for each chip family. After that, the driver can setup the
switch accordingly. Keep only the first supported model for each family
as a compatible string and reference other chip models in the
description.
The removed compatible strings have never been used in a released kernel.
Link: https://lore.kernel.org/netdev/20220414014055.m4wbmr7tdz6hsa3m@bang-olufsen.dk/
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Link: https://lore.kernel.org/r/20220418233558.13541-1-luizluca@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Absolute paths in $ref should always begin with '/schemas'. The tools
mostly work with it omitted, but for correctness the path should be
everything except the hostname as that is taken from the schema's $id
value. This scheme is defined in the json-schema spec.
Cc: Hector Martin <marcan@marcan.st>
Cc: Sven Peter <sven@svenpeter.dev>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mukesh Savaliya <msavaliy@codeaurora.org>
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Bayi Cheng <bayi.cheng@mediatek.com>
Cc: Chuanhong Guo <gch981213@gmail.com>
Cc: Min Guo <min.guo@mediatek.com>
Cc: netdev@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Mark Brown <broonie@debian.org>
Link: https://lore.kernel.org/r/20220325215652.525383-1-robh@kernel.org
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the source
level syntax information. There's a bunch of schema fixes as a result
of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial filename
or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass messages
also now print by default at PR_INFO level to help test automation.
-----BEGIN PGP SIGNATURE-----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=g1li
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Add Krzysztof Kozlowski as co-maintainer for DT bindings providing
much needed help.
- DT schema validation now takes DTB files as input rather than
intermediate YAML files. This decouples the validation from the
source level syntax information. There's a bunch of schema fixes as a
result of switching to DTB based validation which exposed some errors
and incomplete schemas and examples.
- Kbuild improvements to explicitly warn users running 'make
dt_binding_check' on missing yamllint
- Expand DT_SCHEMA_FILES kbuild variable to take just a partial
filename or path instead of the full path to 1 file.
- Convert various bindings to schema format: mscc,vsc7514-switch,
multiple GNSS bindings, ahci-platform, i2c-at91, multiple UFS
bindings, cortina,gemini-sata-bridge, cortina,gemini-ethernet, Atmel
SHA, Atmel TDES, Atmel AES, armv7m-systick, Samsung Exynos display
subsystem, nuvoton,npcm7xx-timer, samsung,s3c2410-i2c, zynqmp_dma,
msm/mdp4, rda,8810pl-uart
- New schemas for u-boot environment variable partition, TI clksel
- New compatible strings for Renesas RZ/V2L SoC
- Vendor prefixes for Xen, HPE, deprecated Synopsys, deprecated
HiSilicon
- Add/fix schemas for QEMU Arm 'virt' machine
- Drop unused of_alias_get_alias_list() function
- Add a script to check DT unittest EXPECT message output. Pass
messages also now print by default at PR_INFO level to help test
automation.
* tag 'devicetree-for-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (96 commits)
dt-bindings: kbuild: Make DT_SCHEMA_LINT a recursive variable
dt-bindings: nvmem: add U-Boot environment variables binding
dt-bindings: ufs: qcom: Add SM6350 compatible string
dt-bindings: dmaengine: sifive,fu540-c000: include generic schema
dt-bindings: gpio: pca95xx: drop useless consumer example
Revert "of: base: Introduce of_alias_get_alias_list() to check alias IDs"
dt-bindings: virtio,mmio: Allow setting devices 'dma-coherent'
dt-bindings: gnss: Add two more chips
dt-bindings: gnss: Rewrite sirfstar binding in YAML
dt-bindings: gnss: Modify u-blox to use common bindings
dt-bindings: gnss: Rewrite common bindings in YAML
dt-bindings: ata: ahci-platform: Add rk3568-dwc-ahci compatible
dt-bindings: ata: ahci-platform: Add power-domains property
dt-bindings: ata: ahci-platform: Convert DT bindings to yaml
dt-bindings: kbuild: Use DTB files for validation
dt-bindings: kbuild: Pass DT_SCHEMA_FILES to dt-validate
dt-bindings: Add QEMU virt machine compatible
dt-bindings: arm: Convert QEMU fw-cfg to DT schema
dt-bindings: i2c: at91: Add SAMA7G5 compatible strings list
dt-bindings: i2c: convert i2c-at91 to json-schema
...
Realtek rtl8365mb DSA driver can use these two tag formats.
Cc: devicetree@vger.kernel.org
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schema changes:
- support for mdio-connected switches (mdio driver), recognized by
checking the presence of property "reg"
- new compatible strings for rtl8367s and rtl8367rb
- "interrupt-controller" was not added as a required property. It might
still work polling the ports when missing.
Examples changes:
- renamed "switch_intc" to make it unique between examples
- removed "dsa-mdio" from mdio compatible property
- renamed phy@0 to ethernet-phy@0 (not tested with real HW)
phy@ requires #phy-cells
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'phandle-array' type is a bit ambiguous. It can be either just an
array of phandles or an array of phandles plus args. Many schemas for
phandle-array properties aren't clear in the schema which case applies
though the description usually describes it.
The array of phandles case boils down to needing:
items:
maxItems: 1
The phandle plus args cases should typically take this form:
items:
- items:
- description: A phandle
- description: 1st arg cell
- description: 2nd arg cell
With this change, some examples need updating so that the bracketing of
property values matches the schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220119015038.2433585-1-robh@kernel.org
Document the new microchip,synclko-disable property which can be
specified to disable the reference clock output from the device if not
required by the board design.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bindings:
- DT schema conversions for Samsung clocks, RNG bindings, Qcom Command
DB and rmtfs, gpio-restart, i2c-mux-gpio, i2c-mux-pinctl, Tegra I2C
and BPMP, pwm-vibrator, Arm DSU, and Cadence macb
- DT schema conversions for Broadcom platforms: interrupt controllers,
STB GPIO, STB waketimer, STB reset, iProc MDIO mux, iProc PCIe,
Cygnus PCIe PHY, PWM, USB BDC, BCM6328 LEDs, TMON, SYSTEMPORT, AMAC,
Northstar 2 PCIe PHY, GENET, moca PHY, GISB arbiter, and SATA
- Add binding schemas for Tegra210 EMC table, TI DC-DC converters,
- Clean-ups of MDIO bus schemas to fix 'unevaluatedProperties' issues
- More fixes due to 'unevaluatedProperties' enabling
- Data type fixes and clean-ups of binding examples found in preparation
to move to validating DTB files directly (instead of intermediate YAML
representation.
- Vendor prefixes for T-Head Semiconductor, OnePlus, and Sunplus
- Add various new compatible strings
DT core:
- Silence a warning for overlapping reserved memory regions
- Reimplement unittest overlay tracking
- Fix stack frame size warning in unittest
- Clean-ups of early FDT scanning functions
- Fix handling of "linux,usable-memory-range" on EFI booted systems
- Add support for 'fail' status on CPU nodes
- Improve error message in of_phandle_iterator_next()
- kbuild: Disable duplicate unit-address warnings for disabled nodes
-----BEGIN PGP SIGNATURE-----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=2g8v
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"Bindings:
- DT schema conversions for Samsung clocks, RNG bindings, Qcom
Command DB and rmtfs, gpio-restart, i2c-mux-gpio, i2c-mux-pinctl,
Tegra I2C and BPMP, pwm-vibrator, Arm DSU, and Cadence macb
- DT schema conversions for Broadcom platforms: interrupt
controllers, STB GPIO, STB waketimer, STB reset, iProc MDIO mux,
iProc PCIe, Cygnus PCIe PHY, PWM, USB BDC, BCM6328 LEDs, TMON,
SYSTEMPORT, AMAC, Northstar 2 PCIe PHY, GENET, moca PHY, GISB
arbiter, and SATA
- Add binding schemas for Tegra210 EMC table, TI DC-DC converters,
- Clean-ups of MDIO bus schemas to fix 'unevaluatedProperties' issues
- More fixes due to 'unevaluatedProperties' enabling
- Data type fixes and clean-ups of binding examples found in
preparation to move to validating DTB files directly (instead of
intermediate YAML representation.
- Vendor prefixes for T-Head Semiconductor, OnePlus, and Sunplus
- Add various new compatible strings
DT core:
- Silence a warning for overlapping reserved memory regions
- Reimplement unittest overlay tracking
- Fix stack frame size warning in unittest
- Clean-ups of early FDT scanning functions
- Fix handling of "linux,usable-memory-range" on EFI booted systems
- Add support for 'fail' status on CPU nodes
- Improve error message in of_phandle_iterator_next()
- kbuild: Disable duplicate unit-address warnings for disabled nodes"
* tag 'devicetree-for-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (114 commits)
dt-bindings: net: mdio: Drop resets/reset-names child properties
dt-bindings: clock: samsung: convert S5Pv210 to dtschema
dt-bindings: clock: samsung: convert Exynos5410 to dtschema
dt-bindings: clock: samsung: convert Exynos5260 to dtschema
dt-bindings: clock: samsung: extend Exynos7 bindings with UFS
dt-bindings: clock: samsung: convert Exynos7 to dtschema
dt-bindings: clock: samsung: convert Exynos5433 to dtschema
dt-bindings: i2c: maxim,max96712: Add bindings for Maxim Integrated MAX96712
dt-bindings: iio: adi,ltc2983: Fix 64-bit property sizes
dt-bindings: power: maxim,max17040: Fix incorrect type for 'maxim,rcomp'
dt-bindings: interrupt-controller: arm,gic-v3: Fix 'interrupts' cell size in example
dt-bindings: iio/magnetometer: yamaha,yas530: Fix invalid 'interrupts' in example
dt-bindings: clock: imx5: Drop clock consumer node from example
dt-bindings: Drop required 'interrupt-parent'
dt-bindings: net: ti,dp83869: Drop value on boolean 'ti,max-output-impedance'
dt-bindings: net: wireless: mt76: Fix 8-bit property sizes
dt-bindings: PCI: snps,dw-pcie-ep: Drop conflicting 'max-functions' schema
dt-bindings: i2c: st,stm32-i2c: Make each example a separate entry
dt-bindings: net: stm32-dwmac: Make each example a separate entry
dt-bindings: net: Cleanup MDIO node schemas
...
The schemas for MDIO bus nodes range from missing to duplicating
everything in mdio.yaml. The MDIO bus node schemas only need to
reference mdio.yaml, define any binding specific properties, and define
'unevaluatedProperties: false'. This ensures that MDIO nodes only
contain defined properties. With this, any duplicated properties can
be removed.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Cc: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Cc: "Fernández Rojas" <noltari@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: "G. Jaya Kumaran" <vineetha.g.jaya.kumaran@intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220105151009.3093506-1-robh@kernel.org
Clean and improve port definition for qca8k documentation by referencing
the dsa generic port definition and adding the additional specific port
definition.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch may require to add additional binding to the node port.
Move DSA generic port definition to a dedicated yaml to permit this.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a schema validator to nxp,sja1105.yaml and to dsa.yaml for explicit
MAC-level RGMII delays. These properties must be per port and must be
present only for a phy-mode that represents RGMII.
We tell dsa.yaml that these port properties might be present, we also
define their valid values for SJA1105. We create a common definition for
the RX and TX valid range, since it's quite a mouthful.
We also modify the example to include the explicit RGMII delay properties.
On the fixed-link ports (in the example, port 4), having these explicit
delays is actually mandatory, since with the new behavior, the driver
shouts that it is interpreting what delays to apply based on phy-mode.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since a switch is basically a bunch of Ethernet controllers, just
inherit the common schema for one to get stronger type validation of the
properties of a port.
For example, before this change it was valid to have a phy-mode = "xfi"
even if "xfi" is not part of ethernet-controller.yaml, now it is not.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All ports require either a phy-handle or a fixed-link, and port 3 in the
example didn't have one. Add it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rtl8365mb is a new realtek-smi subdriver for the RTL8365MB-VC 4+1 port
10/100/1000M Ethernet switch controller. Its compatible string is
"realtek,rtl8365mb".
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the qca8k bindings to YAML format.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Co-developed-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8328 is the bigger brother of qca8327. Document the new compatible
binding and add some information to understand the various switch
compatible.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document new binding qca,ignore-power-on-sel used to ignore
power on strapping and use sw regs instead.
Document qca,led-open.drain to set led to open drain mode, the
qca,ignore-power-on-sel is mandatory with this enabled or an error will
be reported.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document qca,sgmii-enable-pll binding used in the CPU nodes to
enable SGMII PLL on MAC config.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch now support CPU port to be set 6 instead of be hardcoded to
0. Document support for it and describe logic selection.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add names and descriptions of additional PORT0_PAD_CTRL properties.
qca,sgmii-(rx|tx)clk-falling-edge are for setting the respective clock
phase to failling edge.
Co-developed-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Vitesse/Microsemi/Microchip family of switches supported by the
Felix DSA driver is capable of selecting between the native tagging
protocol and ocelot-8021q. This is necessary to enable flow control on
the CPU port.
Certain systems where these switches are integrated use the switch as a
port multiplexer, so the termination throughput is paramount. Changing
the tagging protocol at runtime is possible for these systems, but since
it is known beforehand that one tagging protocol will provide strictly
better performance than the other, just allow them to specify the
preference in the device tree.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a trivial typo when spelling "protocol", fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the MV88E6390 switch chip exists, one is supposed to use a
compatible of "marvell,mv88e6190" for it. Fix this in the given example.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Fixes: a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the lines aren't properly indented, causing yamllint to warn
about them:
.../nxp,sja1105.yaml:70:17: [warning] wrong indentation: expected 18 but found 16 (indentation)
Use the proper indentation to fix those warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fixes: 070f5b701d ("dt-bindings: net: dsa: sja1105: add SJA1110 bindings")
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210622113327.3613595-1-thierry.reding@gmail.com
Signed-off-by: Rob Herring <robh@kernel.org>
- Refine reserved memory nomap handling
- Merge some PCI and non-PCI address handling implementations
- Simplify of_address.h header ifdefs
- Improve printk handling of some 64-bit types
- Convert Arm ccree, Zynq FPGA, ZynqMP RTC, Arm VIC, adi,adv7511, TI
AM56 PCI, Aspeed I2C, arm,sbsa-gwdt, MTD physmap, virtio-mmio, Arm
SCMI, Arm/Amlogic SCPI, TI OMAP mailbox, NXP pcf8563/pcf85263/pcf85363,
Mediatek RNG, Arm SCU, Arm TWD timer, Broadcom iProc PWM, Renesas TPU,
Tegra20 EMC, MDIO GPIO, renesas,r9a06g032-sysctrl, renesas,emev2-smu,
sysc-rmobile, linaro,optee-tz, and TI SCI bindings to DT schema
- Convert mux and mux controller bindings to schema. This includes MDIO
IIO, and I2C muxes.
- Add Arm PL031 RTC binding schema
- Add vendor prefixes for StarFive Technology Co. Ltd. and Insignal Ltd
- Fix some stale doc references
- Remove stale property-units.txt. Superseded by schema in dt-schema
repo.
- Fixes for 'unevaluatedProperties' handling (enabled with experimental
json-schema support)
- Drop redundant usage of minItems and maxItems across the tree
- Update some examples to use bindings with a schema
-----BEGIN PGP SIGNATURE-----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=MDNZ
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Refine reserved memory nomap handling
- Merge some PCI and non-PCI address handling implementations
- Simplify of_address.h header ifdefs
- Improve printk handling of some 64-bit types
- Convert adi,adv7511, Arm ccree, Arm SCMI, Arm SCU, Arm TWD timer, Arm
VIC, arm,sbsa-gwdt, Arm/Amlogic SCPI, Aspeed I2C, Broadcom iProc PWM,
linaro,optee-tz, MDIO GPIO, Mediatek RNG, MTD physmap, NXP
pcf8563/pcf85263/pcf85363, Renesas TPU, renesas,emev2-smu,
renesas,r9a06g032-sysctrl, sysc-rmobile, Tegra20 EMC, TI AM56 PCI, TI
OMAP mailbox, TI SCI bindings, virtio-mmio, Zynq FPGA, and ZynqMP RTC
to DT schema
- Convert mux and mux controller bindings to schema. This includes MDIO
IIO, and I2C muxes.
- Add Arm PL031 RTC binding schema
- Add vendor prefixes for StarFive Technology Co. Ltd. and Insignal Ltd
- Fix some stale doc references
- Remove stale property-units.txt. Superseded by schema in dt-schema
repo.
- Fixes for 'unevaluatedProperties' handling (enabled with experimental
json-schema support)
- Drop redundant usage of minItems and maxItems across the tree
- Update some examples to use bindings with a schema
* tag 'devicetree-for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (83 commits)
dt-bindings: Fix 'unevaluatedProperties' errors in DT graph users
dt-bindings: display: renesas,du: Fix 'ports' reference
dt-bindings: media: adv7180: Add missing video-interfaces.yaml reference
dt-bindings: crypto: ccree: Convert to json-schema
dt-bindings: fpga: zynq: convert bindings to YAML
dt-bindings: rtc: zynqmp: convert bindings to YAML
dt-bindings: interrupt-controller: Convert ARM VIC to json-schema
of: of_reserved_mem: mark nomap memory instead of removing
of: of_reserved_mem: only call memblock_free for normal reserved memory
dt-bindings: Drop redundant minItems/maxItems
dt-bindings: spmi: Correct 'reg' schema
of: reserved-memory: Add stub for RESERVEDMEM_OF_DECLARE()
dt-bindings: clk: vc5: Fix example
dt-bindings: timer: renesas,tmu: add r8a779a0 TMU support
dt-bindings: drm: bridge: adi,adv7511.txt: convert to yaml
dt-bindings: PCI: ti,am65: Convert PCIe host/endpoint mode dt-bindings to YAML
of: Remove superfluous casts when printing u64 values
of: Fix truncation of memory sizes on 32-bit platforms
dt-bindings: rtc: nxp,pcf8563: Absorb pcf85263/pcf85363 bindings
dt-bindings: pwm: Use examples with documented/matching schema
...
If a property has an 'items' list, then a 'minItems' or 'maxItems' with the
same size as the list is redundant and can be dropped. Note that is DT
schema specific behavior and not standard json-schema behavior. The tooling
will fixup the final schema adding any unspecified minItems/maxItems.
This condition is partially checked with the meta-schema already, but
only if both 'minItems' and 'maxItems' are equal to the 'items' length.
An improved meta-schema is pending.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for MMC
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20210615191543.1043414-1-robh@kernel.org
There are 4 variations of the SJA1110 switch which have a different set
of MII protocols supported per port. Document the compatible strings.
Also, the SJA1110 optionally supports 2 internal MDIO buses for 2
different types of Ethernet PHYs. Document a container node called
"mdios" which has 2 subnodes "mdio@0" and "mdio@1", identifiable via
compatible string, under which the driver finds the internal PHYs.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the sja1105 driver no longer has any custom device tree
properties, the conversion is trivial.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that both RevMII as well as RevRMII exist, we can deprecate the
sja1105,role-mac and sja1105,role-phy properties and simply let the user
select that a port operates in MII PHY role by using
phy-mode = "rev-mii";
or in RMII PHY role by using
phy-mode = "rev-rmii";
There are no fixed-link MII or RMII properties in mainline device trees,
and the setup itself is fairly uncommon, so there shouldn't be risks of
breaking compatibility.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding to support MT7530 interrupt controller.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document new way of declare mapping of internal PHY to port.
The new implementation directly declare the PHY connected to the port
by adding a node in the switch node. The driver detect this and register
an internal mdiobus using the mapping defined in the mdio node.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for qca8327 in the compatible list.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a 3-Port 10/100 Ethernet Switch. One CPU-Port and two
Switch-Ports.
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'dsa-tag-protocol' is used to force a switch tree to use a
particular tag protocol, typically because the Ethernet controller
that it is connected to is not compatible with the default one.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string for xRX300 and xRX330 SoCs.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding to support MT7530 GPIO controller.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add documentation and an example for Arrow SpeedChips XRS7000 Series
single chip Ethernet switches.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This helps validating DTS files. Only the current (not deprecated one)
binding was converted.
Minor changes:
1. Dropped dsa/dsa.txt references
2. Updated node name to match dsa.yaml requirement
3. Fixed 2 typos in examples
The new binding was validated using the dt_binding_check.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20210106213202.17459-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The correct syntax for JSON pointers begins with a '/' after the '#'.
Without a '/', the string should be interpreted as a subschema
identifier. The jsonschema module currently doesn't handle subschema
identifiers and incorrectly allows JSON pointers to begin without a '/'.
Let's fix this before it becomes a problem when jsonschema module is
fixed.
Converted with:
perl -p -i -e 's/yaml#definitions/yaml#\/definitions/g' `find Documentation/devicetree/bindings/ -name "*.yaml"`
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: netdev@vger.kernel.org
Acked-By: Vinod Koul <vkoul@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20201217223429.354283-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already support.
This is also known as the SigmaStar SSD202D, and we add support for
the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the Ampere
Altra based "Fii Kudo" server and the Quanta GSJ, both of which are
added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last year's
generation, also added along with its reference board. This one is
still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into low-end
tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM,
and one machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board
for the aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape
LX2162A, which is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based board,
- IEI Puzzle-M801, a rackmount network appliance based on
Marvell Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm
sm8250 and sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook
(sc7180)
- New board variants of the Renesas based "Kingfisher" and
"HiHope" reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with
a few carrier boards.
There is one conflict in mt6577_auxadc.txt, which got replaced in
another tree and modified here, the modification is already part of
the new file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=R47r
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
