Add registers that are used to configure the PTP pins. These registers
are used to enable the interrupts per PTP pin and to set the waveform
generated by the pin.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To read/write a value to a PHC, it is required to use a PTP pin.
Currently it is used pin 5, but change to pin 7 as is the last pin.
All the other pins will have different functions.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only remaining definitions of __SLOW_DOWN_IO (for alpha and ia64) do
nothing, and the only mentions in networking are in comments. Remove these
mentions.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
atp.h is included only by atp.c, which does not use eeprom_delay(). Remove
the unused definition.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need to wait 5 s for EMP reset after firmware flash. Code was extracted
from OOT driver (ice v1.8.3 downloaded from sourceforge). Without this
wait, fw_activate let card in inconsistent state and recoverable only
by second flash/activate. Flash was tested on these fw's:
From -> To
3.00 -> 3.10/3.20
3.10 -> 3.00/3.20
3.20 -> 3.00/3.10
Reproducer:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
71: ens7f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
dmesg after flash:
[ 55.120788] ice: Copyright (c) 2018, Intel Corporation.
[ 55.274734] ice 0000:ca:00.0: Get PHY capabilities failed status = -5, continuing anyway
[ 55.569797] ice 0000:ca:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.28.0
[ 55.603629] ice 0000:ca:00.0: Get PHY capability failed.
[ 55.608951] ice 0000:ca:00.0: ice_init_nvm_phy_type failed: -5
[ 55.647348] ice 0000:ca:00.0: PTP init successful
[ 55.675536] ice 0000:ca:00.0: DCB is enabled in the hardware, max number of TCs supported on this port are 8
[ 55.685365] ice 0000:ca:00.0: FW LLDP is disabled, DCBx/LLDP in SW mode.
[ 55.692179] ice 0000:ca:00.0: Commit DCB Configuration to the hardware
[ 55.701382] ice 0000:ca:00.0: 126.024 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x8 link at 0000:c9:02.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
Reboot doesn’t help, only second flash/activate with OOT or patched
driver put card back in consistent state.
After patch:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
fw_activate
[root@host ~]# ip link show ens7f0
19: ens7f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
altname enp202s0f0
Fixes: 399e27dbbd ("ice: support immediate firmware activation via devlink reload")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previous patch labelled "ice: Fix incorrect locking in
ice_vc_process_vf_msg()" fixed an issue with ignored messages
sent by VF driver but a small race window still left.
Recently caught trace during 'ip link set ... vf 0 vlan ...' operation:
[ 7332.995625] ice 0000:3b:00.0: Clearing port VLAN on VF 0
[ 7333.001023] iavf 0000:3b:01.0: Reset indication received from the PF
[ 7333.007391] iavf 0000:3b:01.0: Scheduling reset task
[ 7333.059575] iavf 0000:3b:01.0: PF returned error -5 (IAVF_ERR_PARAM) to our request 3
[ 7333.059626] ice 0000:3b:00.0: Invalid message from VF 0, opcode 3, len 4, error -1
Setting of VLAN for VF causes a reset of the affected VF using
ice_reset_vf() function that runs with cfg_lock taken:
1. ice_notify_vf_reset() informs IAVF driver that reset is needed and
IAVF schedules its own reset procedure
2. Bit ICE_VF_STATE_DIS is set in vf->vf_state
3. Misc initialization steps
4. ice_sriov_post_vsi_rebuild() -> ice_vf_set_initialized() and that
clears ICE_VF_STATE_DIS in vf->vf_state
Step 3 is mentioned race window because IAVF reset procedure runs in
parallel and one of its step is sending of VIRTCHNL_OP_GET_VF_RESOURCES
message (opcode==3). This message is handled in ice_vc_process_vf_msg()
and if it is received during the mentioned race window then it's
marked as invalid and error is returned to VF driver.
Protect vf_state check in ice_vc_process_vf_msg() by cfg_lock to avoid
this race condition.
Fixes: e6ba5273d4 ("ice: Fix race conditions between virtchnl handling and VF ndo ops")
Tested-by: Fei Liu <feliu@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Usage of mutex_trylock() in ice_vc_process_vf_msg() is incorrect
because message sent from VF is ignored and never processed.
Use mutex_lock() instead to fix the issue. It is safe because this
mutex is used to prevent races between VF related NDOs and
handlers processing request messages from VF and these handlers
are running in ice_service_task() context. Additionally move this
mutex lock prior ice_vc_is_opcode_allowed() call to avoid potential
races during allowlist access.
Fixes: e6ba5273d4 ("ice: Fix race conditions between virtchnl handling and VF ndo ops")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The hardware checksum offloading requires use of a transmit
status block inserted before the outgoing frame data, this was
updated in '9a9ba2a4aaaa ("net: bcmgenet: always enable status blocks")'
However, skb_tx_timestamp() assumes that it is passed a raw frame
and PTP parsing chokes on this status block.
Fix this by calling __skb_pull(), which hides the TSB before calling
skb_tx_timestamp(), so an outgoing PTP packet is parsed correctly.
As the data in the skb has already been set up for DMA, and the
dma_unmap_* calls use a separately stored address, there is no
no effective change in the data transmission.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220424165307.591145-1-jonathan.lemon@gmail.com
Fixes: d03825fba4 ("net: bcmgenet: add skb_tx_timestamp call")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
DSA, through dsa_port_bridge_leave(), first notifies the port of the
fact that it left a bridge, then, if that bridge was VLAN-aware, it
notifies the port of the change in VLAN awareness state, towards
VLAN-unaware mode.
So ocelot_port_vlan_filtering() can be called when ocelot_port->bridge
is NULL, and this makes ocelot_add_vlan_unaware_pvid() create a struct
ocelot_bridge_vlan with a vid of 0 and an "untagged" setting of true on
that port.
In a way this structure correctly reflects the reality, but by design,
VID 0 (OCELOT_STANDALONE_PVID) was not meant to be kept in the bridge
VLAN list of the driver, but managed separately.
Having OCELOT_STANDALONE_PVID in ocelot->vlans makes us trip up on
several sanity checks that did not expect to have this VID there.
For example, after we leave a VLAN-aware bridge and we re-join it, we
can no longer program egress-tagged VLANs to hardware:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 nomaster
# ip link set swp0 master br0
# bridge vlan add dev swp0 vid 100
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
But this configuration is in fact supported by the hardware, since we
could use OCELOT_PORT_TAG_NATIVE. According to its comment:
/* all VLANs except the native VLAN and VID 0 are egress-tagged */
yet when assessing the eligibility for this mode, we do not check for
VID 0 in ocelot_port_uses_native_vlan(), instead we just ensure that
ocelot_port_num_untagged_vlans() == 1. This is simply because VID 0
doesn't have a bridge VLAN structure.
The way I identify the problem is that ocelot_port_vlan_filtering(false)
only means to call ocelot_add_vlan_unaware_pvid() when we dynamically
turn off VLAN awareness for a bridge we are under, and the PVID changes
from the bridge PVID to a reserved PVID based on the bridge number.
Since OCELOT_STANDALONE_PVID is statically added to the VLAN table
during ocelot_vlan_init() and never removed afterwards, calling
ocelot_add_vlan_unaware_pvid() for it is not intended and does not serve
any purpose.
Fix the issue by avoiding the call to ocelot_add_vlan_unaware_pvid(vid=0)
when we're resetting VLAN awareness after leaving the bridge, to become
a standalone port.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the felix DSA driver and ocelot switchdev driver declare
dev->features & NETIF_F_HW_VLAN_CTAG_FILTER under certain circumstances*,
so the 8021q module will add VID 0 to our RX filter when the port goes
up, to ensure 802.1p traffic is not dropped.
We treat VID 0 as a special value (OCELOT_STANDALONE_PVID) which
deliberately does not have a struct ocelot_bridge_vlan associated with
it. Instead, this gets programmed to the VLAN table in ocelot_vlan_init().
If we allow external calls to modify VID 0, we reach the following
situation:
# ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up
# ip link set swp0 master br0
# ip link set swp0 up # this adds VID 0 to ocelot->vlans with untagged=false
bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged # the bridge also adds VID 1
br0 1 PVID Egress Untagged
# bridge vlan add dev swp0 vid 100 untagged
Error: mscc_ocelot_switch_lib: Port with egress-tagged VLANs cannot have more than one egress-untagged (native) VLAN.
This configuration should have been accepted, because
ocelot_port_manage_port_tag() should select OCELOT_PORT_TAG_NATIVE.
Yet it isn't, because we have an entry in ocelot->vlans which says
VID 0 should be egress-tagged, something the hardware can't do.
Fix this by suppressing additions/deletions on VID 0 and managing this
VLAN exclusively using OCELOT_STANDALONE_PVID.
*DSA toggles it when the port becomes VLAN-aware by joining a VLAN-aware
bridge. Ocelot declares it unconditionally for some reason.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if the kzalloc() failed.
Fixes: 804775dfc2 ("net: ethernet: mtk_eth_soc: add support for Wireless Ethernet Dispatch (WED)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan966x->ports[] array has lan966x->num_phys_ports elements. These
are assigned in lan966x_probe(). That means the > comparison should be
changed to >=.
The first off by one check is harmless but the second one could lead to
an out of bounds access and a crash.
Fixes: 5ccd66e01c ("net: lan966x: add support for interrupts from analyzer")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the BUG_ON() with returning error code to handle
the fault more gracefully.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
payload only memset but no use at all, so we drop them.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In one of the error paths of the device_for_each_child_node() loop
in hns_mac_init, add missing call to fwnode_handle_put.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there are some querying mailboxes sent from VF to PF,
and VF will wait the PF's handling result. For mailbox
HCLGE_MBX_GET_QID_IN_PF and HCLGE_MBX_GET_RSS_KEY, it may fail
when the input parameter is invalid, but the prototype of their
handler function is void. In this case, PF always return success
to VF, which may cause the VF get incorrect result.
Fixes it by adding return value for these function.
Fixes: 63b1279d99 ("net: hns3: check queue id range before using")
Fixes: 532cfc0df1 ("net: hns3: add a check for index in hclge_get_rss_key()")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add validity check for message data length in function
hclge_send_mbx_msg(), avoid unexpected overflow.
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, function hclge_get_ring_chain_from_mbx will return -ENOMEM if
ring_num is bigger than HCLGE_MBX_MAX_RING_CHAIN_PARAM_NUM. It is better to
return -EINVAL for the invalid parameter case.
So this patch fixes it by return -EINVAL in this abnormal branch.
Fixes: 5d02a58dae ("net: hns3: fix for buffer overflow smatch warning")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments in function hclge_comm_tqps_update_stats is not right,
so fix it.
Fixes: 287db5c40d ("net: hns3: create new set of common tqp stats APIs for PF and VF reuse")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debugfs node rx/tx_queue_info and rx/tx_bd_info, their output info is
aligned to the right, it's not aligned with output of other debugfs node,
so uniform their output info.
Fixes: 907676b130 ("net: hns3: use tx bounce buffer for small packets")
Fixes: e44c495d95 ("net: hns3: refactor queue info of debugfs")
Fixes: 77e9184869 ("net: hns3: refactor dump bd info of debugfs")
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If failed to register netdev, it needs to clear INITED state and stop
client in case of cause problem when concurrency with uninitialized
process of driver.
Fixes: a289a7e5c1 ("net: hns3: put off calling register_netdev() until client initialize complete")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend MDDQ to obtain FW version of line card device and implement
device_info_get() op to fill up the info with that.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add FW version fields to MDDQ device_info.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement info_get() to expose HW revision of a linecard and loaded INI
version.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the line card is provisioned, go over all possible existing
devices (gearboxes) on it and attach them, so devlink core is aware of
them.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing MDDQ register by possibility to query information about
devices residing on a line card.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made a mistake with the commit a6aaa00324 ("net: ethernet: stmmac:
fix altr_tse_pcs function when using a fixed-link"). I should have
tested against both scenario of having a SGMII interface and one
without.
Without the SGMII PCS TSE adpater, the sgmii_adapter_base address is
NULL, thus a write to this address will fail.
Cc: stable@vger.kernel.org
Fixes: a6aaa00324 ("net: ethernet: stmmac: fix altr_tse_pcs function when using a fixed-link")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Link: https://lore.kernel.org/r/20220420152345.27415-1-dinguyen@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
types_info->ini_files is an array of pointers
to struct mlxsw_linecard_ini_file.
Fix the kmalloc_array() argument to be of a size of a pointer.
Addresses-Coverity: ("Incorrect expression (SIZEOF_MISMATCH)")
Fixes: b217127e5e ("mlxsw: core_linecards: Add line card objects and implement provisioning")
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Link: https://lore.kernel.org/r/20220420142007.3041173-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
qed_nvmetcp_ip_services.c and its corresponding header file were
introduced in commit 806ee7f81a ("qed: Add IP services APIs support")
but there's still no users for any of the functions they declare.
Since these files are effectively unused, let's just drop them.
Found by code inspection. Compile-tested only.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Link: https://lore.kernel.org/r/351ac8c847980e22850eb390553f8cc0e1ccd0ce.1650545051.git.gnault@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the macb binding documentation "phys" is an optional property. Make
implementation in line with it. This change allows the traditional flow
in which first stage bootloader does PS-GT configuration to work along
with newer use cases in which PS-GT configuration is managed by the
phy-zynqmp driver.
It fixes below macb probe failure when macb DT node doesn't have SGMII
phys handle.
"macb ff0b0000.ethernet: error -ENODEV: failed to get PS-GTR PHY"
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces some sk_ipv6only tests with ipv6_only_sock().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NFP driver already supports assignment of 802.1Q VLANs to VFs
e.g.
# ip link set $DEV vf $VF_NUM vlan $VLAN_ID [proto 802.1Q]
This patch enhances the NFP driver to also allow assingment of
802.1ad VLANs to VFs.
e.g.
# ip link set $DEV vf $VF_NUM vlan $VLAN_ID proto 802.1ad
Signed-off-by: Bin Chen <bin.chen@corigine.com>
Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com>
Signed-off-by: Yinjun Zhang <yunjin.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable status is being assigned a value that is never read, it is
being re-assigned again later on. The assignment is redundant and can
be removed.
Cleans up clang scan build warning:
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:582:7: warning: Although
the value stored to 'status' is used in the enclosing expression, the
value is never actually read from 'status' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel drivers translate actions returned from XDP programs to their own
return codes that have the following mapping:
XDP_REDIRECT -> I40E_XDP_{REDIR,CONSUMED}
XDP_TX -> I40E_XDP_{TX,CONSUMED}
XDP_DROP -> I40E_XDP_CONSUMED
XDP_ABORTED -> I40E_XDP_CONSUMED
XDP_PASS -> I40E_XDP_PASS
Commit b8aef650e5 ("i40e, xsk: Terminate Rx side of NAPI when XSK Rx
queue gets full") introduced new translation
XDP_REDIRECT -> I40E_XDP_EXIT
which is set when XSK RQ gets full and to indicate that driver should
stop further Rx processing. This happens for unsuccessful
xdp_do_redirect() so it is valuable to call trace_xdp_exception() for
this case. In order to avoid I40E_XDP_EXIT -> IXGBE_XDP_CONSUMED
overwrite, XDP_DROP case was moved above which in turn made the
'fallthrough' that is in XDP_ABORTED useless as it became the last label
in the switch statement.
Simply drop this leftover.
Fixes: b8aef650e5 ("i40e, xsk: Terminate Rx side of NAPI when XSK Rx queue gets full")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220421132126.471515-3-maciej.fijalkowski@intel.com
Intel drivers translate actions returned from XDP programs to their own
return codes that have the following mapping:
XDP_REDIRECT -> IXGBE_XDP_{REDIR,CONSUMED}
XDP_TX -> IXGBE_XDP_{TX,CONSUMED}
XDP_DROP -> IXGBE_XDP_CONSUMED
XDP_ABORTED -> IXGBE_XDP_CONSUMED
XDP_PASS -> IXGBE_XDP_PASS
Commit c7dd09fd46 ("ixgbe, xsk: Terminate Rx side of NAPI when XSK Rx
queue gets full") introduced new translation
XDP_REDIRECT -> IXGBE_XDP_EXIT
which is set when XSK RQ gets full and to indicate that driver should
stop further Rx processing. This happens for unsuccessful
xdp_do_redirect() so it is valuable to call trace_xdp_exception() for
this case. In order to avoid IXGBE_XDP_EXIT -> IXGBE_XDP_CONSUMED
overwrite, XDP_DROP case was moved above which in turn made the
'fallthrough' that is in XDP_ABORTED useless as it became the last label
in the switch statement.
Simply drop this leftover.
Fixes: c7dd09fd46 ("ixgbe, xsk: Terminate Rx side of NAPI when XSK Rx queue gets full")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220421132126.471515-2-maciej.fijalkowski@intel.com
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220418062921.2557884-1-chi.minghao@zte.com.cn
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add callback functions for line card 'hwmon' initialization and
de-initialization. Each line card is associated with the relevant
'hwmon' device, which may contain thermal attributes for the cages
and gearboxes found on this line card.
The line card 'hwmon' initialization / de-initialization APIs are to be
called when line card is set to active / inactive state by
got_active() / got_inactive() callbacks from line card state machine.
For example cage temperature for module #9 located at line card #7 will
be exposed by utility 'sensors' like:
linecard#07
front panel 009: +32.0C (crit = +70.0C, emerg = +80.0C)
And temperature for gearbox #3 located at line card #5 will be exposed
like:
linecard#05
gearbox 003: +41.0C (highest = +41.0C)
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add callback functions for line card thermal area initialization and
de-initialization. Each line card is associated with the relevant
thermal area, which may contain thermal zones for cages and gearboxes
found on this line card.
The line card thermal initialization / de-initialization APIs are to be
called when line card is set to active / inactive state by
got_active() / got_inactive() callbacks from line card state machine.
For example thermal zone for module #9 located at line card #7 will
have type:
mlxsw-lc7-module9.
And thermal zone for gearbox #2 located at line card #5 will have type:
mlxsw-lc5-gearbox2.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevs for ports found on line cards are registered upon provisioning.
However, user space is not allowed to access the transceiver modules
found on a line card until the line card becomes active.
Therefore, register event operations with the line card core to get
notifications whenever a line card becomes active or inactive.
When user space tries to dump the EEPROM of a transceiver module or reset
it and the corresponding line card is inactive, emit an error
message:
ethtool -m enp1s0nl7p9
netlink error: mlxsw_core: Cannot read EEPROM of module on an inactive line card
netlink error: Input/output error
When user space tries to set the power mode policy of such a transceiver,
cache the configuration and apply it when the line card becomes active. This
is consistent with other port configuration (e.g., MTU setting) that user space
is able to perform while the line card is provisioned, but inactive.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the code that applies the module power mode to the device to a
separate function. This function will be invoked by the next patch to
set the power mode on transceiver modules found on a line card when the
line card becomes active.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass bus argument to mlxsw_env_init(). The purpose is to get access to
device handle, which is to be provided to error message in case of line
card activation failure.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an infrastructure allowing users to register a set
of operations which are to be called whenever a line card gets
active/inactive.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The init_systime() may be invoked in atomic state. We have observed the
following call trace when running "phc_ctl /dev/ptp0 set" on a Intel
Agilex board.
BUG: sleeping function called from invalid context at drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:74
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 381, name: phc_ctl
preempt_count: 1, expected: 0
RCU nest depth: 0, expected: 0
Preemption disabled at:
[<ffff80000892ef78>] stmmac_set_time+0x34/0x8c
CPU: 2 PID: 381 Comm: phc_ctl Not tainted 5.18.0-rc2-next-20220414-yocto-standard+ #567
Hardware name: SoCFPGA Agilex SoCDK (DT)
Call trace:
dump_backtrace.part.0+0xc4/0xd0
show_stack+0x24/0x40
dump_stack_lvl+0x7c/0xa0
dump_stack+0x18/0x34
__might_resched+0x154/0x1c0
__might_sleep+0x58/0x90
init_systime+0x78/0x120
stmmac_set_time+0x64/0x8c
ptp_clock_settime+0x60/0x9c
pc_clock_settime+0x6c/0xc0
__arm64_sys_clock_settime+0x88/0xf0
invoke_syscall+0x5c/0x130
el0_svc_common.constprop.0+0x4c/0x100
do_el0_svc+0x7c/0xa0
el0_svc+0x58/0xcc
el0t_64_sync_handler+0xa4/0x130
el0t_64_sync+0x18c/0x190
So we should use readl_poll_timeout_atomic() here instead of
readl_poll_timeout().
Also adjust the delay time to 10us to fix a "__bad_udelay" build error
reported by "kernel test robot <lkp@intel.com>". I have tested this on
Intel Agilex and NXP S32G boards, there is no delay needed at all.
So the 10us delay should be long enough for most cases.
Fixes: ff8ed73786 ("net: stmmac: use readl_poll_timeout() function in init_systime()")
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary line wrap for hns3_set_tunable to improve
function readability.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Magic values are not recommended.
Signed-off-by: Peng Li<lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes wrong words in comments.
Signed-off-by: Peng Li<lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The param of function hclgevf_get_mbx_resp has been changed but the
comments not upodated. This patch updates it.
Signed-off-by: Peng Li<lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the active tx spare buffer size maybe changed according
to the page size, so add log to notice it.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, There is a low probability that pf mtu configuration fails, but
the information in logs is insufficient for problem locating when the VF
mtu value is illegally modified.
So record the vf index and vf mtu value at the failure scenario.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct hclge_pf_to_vf_msg is used for mailbox message from
PF to VF, including both response and request. But its definition
can only indicate respone, which makes the message data copy in
function hclge_send_mbx_msg() unreadable. So refine it by edding
a general message definition into it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use struct hns3_ring_param to replace variable new/old_xxx and
add hns3_is_ringparam_changed() to judge them if is changed to
improve code readability.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For DEVICE_VERSION_V2, the hardware does not support the CQE mode.
So add capability bit for coalesce CQE mode and add parameter check
for it in ethtool.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_xdp_xmit() is the callback function of .ndo_xdp_xmit.
It internally calls aq_nic_xmit_xdpf() to send packet.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It supports XDP_PASS, XDP_DROP and multi buffer.
The new function aq_nic_xmit_xdpf() is used to send packet with
xdp_frame and internally it calls aq_nic_map_xdp().
AQC chip supports 32 multi-queues and 8 vectors(irq).
there are two option
1. under 8 cores and 4 tx queues per core.
2. under 4 cores and 8 tx queues per core.
Like ixgbe, these tx queues can be used only for XDP_TX, XDP_REDIRECT
queue. If so, no tx_lock is needed.
But this patchset doesn't use this strategy because getting hardware tx
queue index cost is too high.
So, tx_lock is used in the aq_nic_xmit_xdpf().
single-core, single queue, 80% cpu utilization.
30.75% bpf_prog_xxx_xdp_prog_tx [k] bpf_prog_xxx_xdp_prog_tx
10.35% [kernel] [k] aq_hw_read_reg <---------- here
4.38% [kernel] [k] get_page_from_freelist
single-core, 8 queues, 100% cpu utilization, half PPS.
45.56% [kernel] [k] aq_hw_read_reg <---------- here
17.58% bpf_prog_xxx_xdp_prog_tx [k] bpf_prog_xxx_xdp_prog_tx
4.72% [kernel] [k] hw_atl_b0_hw_ring_rx_receive
The new function __aq_ring_xdp_clean() is a xdp rx handler and this is
called only when XDP is attached.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
aq_xdp() is a xdp setup callback function for Atlantic driver.
When XDP is attached or detached, the device will be restarted because
it uses different headroom, tailroom, and page order value.
If XDP enabled, it switches default page order value from 0 to 2.
Because the default maximum frame size is still 2K and it needs
additional area for headroom and tailroom.
The total size(headroom + frame size + tailroom) is 2624.
So, 1472Bytes will be always wasted for every frame.
But when order-2 is used, these pages can be used 6 times
with flip strategy.
It means only about 106Bytes per frame will be wasted.
Also, It supports xdp fragment feature.
MTU can be 16K if xdp prog supports xdp fragment.
If not, MTU can not exceed 2K - ETH_HLEN - ETH_FCS.
And a static key is added and It will be used to call the xdp_clean
handler in ->poll(). data plane implementation will be contained
the followed patch.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the user runs:
bridge link set dev $br_port mcast_flood on
this command should affect not only L2 multicast, but also IPv4 and IPv6
multicast.
In the Ocelot switch, unknown multicast gets flooded according to
different PGIDs according to its type, and PGID_MC only handles L2
multicast. Therefore, by leaving PGID_MCIPV4 and PGID_MCIPV6 at their
default value of 0, unknown IP multicast traffic is never flooded.
Fixes: 421741ea56 ("net: mscc: ocelot: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220415151950.219660-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This will reset deeply on freeze and thaw instead of suspend and
resume and prevent null pointer dereferences of the uninitialized ring
0 buffer while thawing.
The impact is an indefinitely hanging kernel. You can't switch
consoles after this and the only possible user interaction is SysRq.
BUG: kernel NULL pointer dereference
RIP: 0010:aq_ring_rx_fill+0xcf/0x210 [atlantic]
aq_vec_init+0x85/0xe0 [atlantic]
aq_nic_init+0xf7/0x1d0 [atlantic]
atl_resume_common+0x4f/0x100 [atlantic]
pci_pm_thaw+0x42/0xa0
resolves in aq_ring.o to
```
0000000000000ae0 <aq_ring_rx_fill>:
{
/* ... */
baf: 48 8b 43 08 mov 0x8(%rbx),%rax
buff->flags = 0U; /* buff is NULL */
```
The bug has been present since the introduction of the new pm code in
8aaa112a57 ("net: atlantic: refactoring pm logic") and was hidden
until 8ce8427169 ("net: atlantic: changes for multi-TC support"),
which refactored the aq_vec_{free,alloc} functions into
aq_vec_{,ring}_{free,alloc}, but is technically not wrong. The
original functions just always reinitialized the buffers on S3/S4. If
the interface is down before freezing, the bug does not occur. It does
not matter, whether the initrd contains and loads the module before
thawing.
So the fix is to invert the boolean parameter deep in all pm function
calls, which was clearly intended to be set like that.
First report was on Github [1], which you have to guess from the
resume logs in the posted dmesg snippet. Recently I posted one on
Bugzilla [2], since I did not have an AQC device so far.
#regzbot introduced: 8ce8427169
#regzbot from: koo5 <kolman.jindrich@gmail.com>
#regzbot monitor: https://github.com/Aquantia/AQtion/issues/32
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Link: https://github.com/Aquantia/AQtion/issues/32 [1]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215798 [2]
Cc: stable@vger.kernel.org
Reported-by: koo5 <kolman.jindrich@gmail.com>
Signed-off-by: Manuel Ullmann <labre@posteo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each port get slot_index using PMLP register. For ports residing
on a linecard, identify it with the linecard by setting mapping
using devlink_port_linecard_set() helper. Use linecard slot index for
PMTDB register queries.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of line card implementation, the core has to have a way to
remove relevant ports manually. Extend the Spectrum driver ops by an op
that implements port removal of selected ports upon request.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to process events generated upon line card getting "ready" and
"active".
When DSDSC event with "ready" bit set is delivered, that means the
line card is powered up. Use MDDC register to push the line card to
active state. Once FW is done with that, the DSDSC event with "active"
bit set is delivered.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce objects for line cards and an infrastructure around that.
Use devlink_linecard_create/destroy() to register the line card with
devlink core. Implement provisioning ops with a list of supported
line cards.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MBCT register allows to transfer binary INI codes from the host to
the management FW by transferring it by chunks of maximum 1KB.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDDC register allows to control downstream devices and line cards.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDDQ register allows to query the DownStream device properties.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register PMLPE trap and process the port mapping changes delivered
by it by creating related ports. Note that this happens after
provisioning. The INI of the linecard is processed and merged by FW.
PMLPE is generated for each port. Process this mapping change.
Layout of PMLPE is the same as layout of PMLP.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to hold the lock for alloc and freecpu. So narrow the critical
section. Follow-up patch is going to benefit from this by adding more
code to the functions which will be out of the critical as well.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PMECR register is used to enable/disable event triggering
in case of local port mapping change.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of array of pointers to port mapping structures, allocate the
array of structures directly.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, the lane index always started from zero. That is not true for
modular systems with gearbox-equipped linecards. Loose the check so the
lanes can start from non-zero index.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido reported that the commit referenced in the Fixes tag broke
a gre use case with dummy devices. Add a check to ip_tunnel_init_flow
to see if the oif is an l3mdev port and if so set the oif to 0 to
avoid the oif comparison in fib_lookup_good_nhc.
Fixes: 40867d74c3 ("net: Add l3mdev index to flow struct and avoid oif reset for port devices")
Reported-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-04-13
This series contains updates to igc and e1000e drivers.
Sasha removes waiting for hardware semaphore as it could cause an
infinite loop and changes usleep_range() calls done under atomic
context to udelay() for igc. For e1000e, he changes some variables from
u16 to u32 to prevent possible overflow of values.
Vinicius disables PTM when going to suspend as it is causing hang issues
on some platforms for igc.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
e1000e: Fix possible overflow in LTR decoding
igc: Fix suspending when PTM is active
igc: Fix BUG: scheduling while atomic
igc: Fix infinite loop in release_swfw_sync
====================
Link: https://lore.kernel.org/r/20220413170814.2066855-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In review comment [1] was pointed that new code is not supposed
to set driver version and should rely on kernel version instead.
As an outcome of that comment all the dance around setting such
driver version to FW should be removed too, because in upstream
kernel whole driver will have same version so read/write from/to
FW will give same result.
[1] https://lore.kernel.org/all/YladGTmon1x3dfxI@unreal
Fixes: 862cd659a6 ("octeon_ep: Add driver framework and device initialization")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/5d76f3116ee795071ec044eabb815d6c2bdc7dbd.1649922731.git.leonro@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow multiple LTBs in the txpool's ltb_set. i.e rather than using
a single large LTB, use several smaller LTBs.
The first n-1 LTBs will all be of the same size. The size of the last
LTB in the set depends on the number of buffers and buffer (mtu) size.
This strategy hopefully allows more reuse of the initial LTBs and also
reduces the chances of an allocation failure (of the large LTB) when
system is low in memory.
Suggested-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow multiple LTBs in the rxpool's ltb_set. The first n-1 LTBs will all
be of the same size. The size of the last LTB in the set depends on the
number of buffers and buffer (mtu) size.
Having a set of LTBs per pool provides a couple of benefits.
First, with the current value of IBMVNIC_MAX_LTB_SIZE of 16MB, with an
MTU of 9000, we need a LTB (DMA buffer) of that size but the allocation
can fail in low memory conditions. With a set of LTBs per pool, we can
use several smaller (8MB) LTBs and hopefully have fewer allocation
failures. (See also comments in ibmvnic.h on the trade-off with smaller
LTBs)
Second since the kernel limits the size of the DMA buffer to 16MB (based
on MAX_ORDER), with a single DMA buffer per pool, the pool is also limited
to 16MB. This in turn limits the number of buffers per pool to 1763 when
MTU is 9000. With a set of LTBs per pool, we can have upto the max of 4096
buffers per pool even when MTU is 9000.
Suggested-by: Brian King <brking@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define and use interfaces that treat the long term buffer (LTB) of an
rxpool as a set of LTBs rather than a single LTB. The set only has one
LTB for now.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a helper to map a given txpool buffer into its corresponding long
term buffer (LTB) and offset. Currently there is just one LTB per txpool
so the mapping is trivial. When we add support for multiple LTBs per
txpool, this helper will be more useful.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Define a helper to map a given rx pool buffer into its corresponding long
term buffer (LTB) and offset. Currently there is just one LTB per pool so
the mapping is trivial. When we add support for multiple LTBs per pool,
this helper will be more useful.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The local variable 'index' is heavily used in some functions and is
confusing with the presence of other "index" fields like pool->index,
->consumer_index, etc. Rename it to bufidx to better reflect that its
the index of a buffer in the pool.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Dany Madden <drt@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, when debugging AF_XDP workloads, one can correlate the -ENXIO
return code as the case that XSK is not in the bound state. Returning
same code from ndo_xsk_wakeup can be misleading and simply makes it
harder to follow what is going on.
Change ENXIOs in stmmac's ndo_xsk_wakeup() implementation to EINVALs, so
that when probing it is clear that something is wrong on the driver
side, not the xsk_{recv,send}msg.
There is a -ENETDOWN that can happen from both kernel/driver sides
though, but I don't have a correct replacement for this on one of the
sides, so let's keep it that way.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-13-maciej.fijalkowski@intel.com
Currently, when debugging AF_XDP workloads, one can correlate the -ENXIO
return code as the case that XSK is not in the bound state. Returning
same code from ndo_xsk_wakeup can be misleading and simply makes it
harder to follow what is going on.
Change ENXIO in mlx5's ndo_xsk_wakeup() implementation to EINVAL, so
that when probing it is clear that something is wrong on the driver
side, not the xsk_{recv,send}msg.
There is a -ENETDOWN that can happen from both kernel/driver sides
though, but I don't have a correct replacement for this on one of the
sides, so let's keep it that way.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-12-maciej.fijalkowski@intel.com
Currently, when debugging AF_XDP workloads, one can correlate the -ENXIO
return code as the case that XSK is not in the bound state. Returning
same code from ndo_xsk_wakeup can be misleading and simply makes it
harder to follow what is going on.
Change ENXIOs in ixgbe's ndo_xsk_wakeup() implementation to EINVALs, so
that when probing it is clear that something is wrong on the driver
side, not the xsk_{recv,send}msg.
There is a -ENETDOWN that can happen from both kernel/driver sides
though, but I don't have a correct replacement for this on one of the
sides, so let's keep it that way.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-11-maciej.fijalkowski@intel.com
Currently, when debugging AF_XDP workloads, one can correlate the -ENXIO
return code as the case that XSK is not in the bound state. Returning
same code from ndo_xsk_wakeup can be misleading and simply makes it
harder to follow what is going on.
Change ENXIOs in i40e's ndo_xsk_wakeup() implementation to EINVALs, so
that when probing it is clear that something is wrong on the driver
side, not the xsk_{recv,send}msg.
There is a -ENETDOWN that can happen from both kernel/driver sides
though, but I don't have a correct replacement for this on one of the
sides, so let's keep it that way.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-10-maciej.fijalkowski@intel.com
Currently, when debugging AF_XDP workloads, one can correlate the -ENXIO
return code as the case that XSK is not in the bound state. Returning
same code from ndo_xsk_wakeup can be misleading and simply makes it
harder to follow what is going on.
Change ENXIOs in ice's ndo_xsk_wakeup() implementation to EINVALs, so
that when probing it is clear that something is wrong on the driver
side, not the xsk_{recv,send}msg.
There is a -ENETDOWN that can happen from both kernel/driver sides
though, but I don't have a correct replacement for this on one of the
sides, so let's keep it that way.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-9-maciej.fijalkowski@intel.com
When XSK pool uses need_wakeup feature, correlate -ENOBUFS that was
returned from xdp_do_redirect() with a XSK Rx queue being full. In such
case, terminate the Rx processing that is being done on the current HW
Rx ring and let the user space consume descriptors from XSK Rx queue so
that there is room that driver can use later on.
Introduce new internal return code IXGBE_XDP_EXIT that will indicate case
described above.
Note that it does not affect Tx processing that is bound to the same
NAPI context, nor the other Rx rings.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-8-maciej.fijalkowski@intel.com
When XSK pool uses need_wakeup feature, correlate -ENOBUFS that was
returned from xdp_do_redirect() with a XSK Rx queue being full. In such
case, terminate the Rx processing that is being done on the current HW
Rx ring and let the user space consume descriptors from XSK Rx queue so
that there is room that driver can use later on.
Introduce new internal return code I40E_XDP_EXIT that will indicate case
described above.
Note that it does not affect Tx processing that is bound to the same
NAPI context, nor the other Rx rings.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-7-maciej.fijalkowski@intel.com
When XSK pool uses need_wakeup feature, correlate -ENOBUFS that was
returned from xdp_do_redirect() with a XSK Rx queue being full. In such
case, terminate the Rx processing that is being done on the current HW
Rx ring and let the user space consume descriptors from XSK Rx queue so
that there is room that driver can use later on.
Introduce new internal return code ICE_XDP_EXIT that will indicate case
described above.
Note that it does not affect Tx processing that is bound to the same
NAPI context, nor the other Rx rings.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-6-maciej.fijalkowski@intel.com
ixgbe_run_xdp_zc() suggests to compiler that XDP_REDIRECT is the most
probable action returned from BPF program that AF_XDP has in its
pipeline. Let's also bring this suggestion up to the callsite of
ixgbe_run_xdp_zc() so that compiler will be able to generate more
optimized code which in turn will make branch predictor happy.
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-5-maciej.fijalkowski@intel.com
ice_run_xdp_zc() suggests to compiler that XDP_REDIRECT is the most
probable action returned from BPF program that AF_XDP has in its
pipeline. Let's also bring this suggestion up to the callsite of
ice_run_xdp_zc() so that compiler will be able to generate more
optimized code which in turn will make branch predictor happy.
Suggested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20220413153015.453864-4-maciej.fijalkowski@intel.com
This patch adds tx push param to hns3 ring param and adapts the set and get
API of ring params. So users can set it by cmd ethtool -G and get it by cmd
ethtool -g.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The displayed list of Ethernet devices in make menuconfig
has gotten out of order. This is mostly due to changes in vendor
names etc, but also because of new Microsoft entry in wrong place.
This restores so that the display is in order even if the names
of the sub directories are not.
Fixes: ca9c54d2d6 ("net: mana: Add a driver for Microsoft Azure Network Adapter (MANA)")
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If register_netdev() fails , it should return error
code in octep_probe().
Fixes: 862cd659a6 ("octeon_ep: Add driver framework and device initialization")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BUFFER_ALIGN macro is used to calculate the number of bytes
required for the next alignment. Instead of this, we can directly
use the skb_reserve(skb, NET_IP_ALIGN) to make the protocol header
buffer aligned on at least a 4-byte boundary, where the NET_IP_ALIGN
is by default defined as 2. So removing the BUFFER_ALIGN and its
related defines which it can be done by the skb_reserve() itself.
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
