Support loading and storing ini TLVs from external
file. Those TLVs are appended to the default TLVs,
so store them separately.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new debug ini TLVs can be either packed into firmware
binary or written in external file. Support loading them
from both. Store the data per apply point. Apply point is
a point during driver runtime, where the TLV becomes active.
For example, a trigger of hardware error may be configured
to collect a subset of data pre-alive, as a opposed to HW
error that occurs after alive.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the FW API of the new debug infrastructure. Next patches
will introduce the utilization of this infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to check the TWT support of the peer and to
propagte the capability to the firmware.
The current implementation will enable TWT only if the TWT
support is advertised in the HE CAP IE and in the Extended
Capability IE.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW dump was missing in case the RT FW ucode
section failed to load. This failure happens when
the RT section of the FW file is corrupted.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have to choose different configuration and different firmwares
depending on the external RF module that is installed. Since the
external module is not represented in the PCI IDs, we need to change
the configuration at runtime, after checking the RF ID of the module
installed. We have a bit of a mess in the code that does this,
because it applies cfg's according to the RF ID only, ignoring the
integrated module that is in use.
Fix that for some devices by adding correct configurations for them
and not ignoring the integrated module's type when making the
decision.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware stopped looking at this field long ago.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split the dump of RXF and TXF. This is in order to
enable code reuse for INI, which may decide to dump
only RXF and not TXF, and vice versa.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently opmode is limited to asking transport to either
dump all the dumps configured at startup, or monitor only.
Instead, pass to transport a bitmask, to allow flexibility.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can't use SAR Geo if basic SAR is not enabled, since the SAR Geo
tables define offsets in relation to the basic SAR table in use.
To fix this, make iwl_mvm_sar_init() return one in case WRDS is not
available, so we can skip reading WGDS entirely.
Fixes: a6bff3cb19 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver is unloaded when D3 debug data pulling is enabled
but not triggered, it doesn't release the data buffer.
Fix this by adding iwl_fw_runtime_free and calling it from the
relevant places.
Fixes: 2d8c261511 ("iwlwifi: add d3 debug data support")
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware starts, it doesn't have any regulatory
information, hence it uses the world wide limitations. The
driver can feed the firmware with previous knowledge that
was kept in the driver, but the firmware may still not
update its internal tables.
This happens when we start a BSS interface, and then the
firmware can change the regulatory tables based on our
location and it'll use more lenient, location specific
rules. Then, if the firmware is shut down (when the
interface is brought down), and then an AP interface is
created, the firmware will forget the country specific
rules.
The host will think that we are in a certain country that
may allow channels and will try to teach the firmware about
our location, but the firmware may still not allow to drop
the world wide limitations and apply country specific rules
because it was just re-started.
In this case, the firmware will reply with MCC_RESP_ILLEGAL
to the MCC_UPDATE_CMD. In that case, iwlwifi needs to let
the upper layers (cfg80211 / hostapd) know that the channel
list they know about has been updated.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=201105
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The oldest firmware supported by iwlmvm do support getting
the average beacon RSSI. Enable the sta_statistics() call
from mac80211 even on older firmware versions.
Fixes: 33cef92563 ("iwlwifi: mvm: support beacon statistics for BSS client")
Cc: stable@vger.kernel.org # 4.2+
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
From coreboot/BIOS:
Name ("WGDS", Package() {
Revision,
Package() {
DomainType, // 0x7:WiFi ==> We miss this one.
WgdsWiFiSarDeltaGroup1PowerMax1, // Group 1 FCC 2400 Max
WgdsWiFiSarDeltaGroup1PowerChainA1, // Group 1 FCC 2400 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB1, // Group 1 FCC 2400 B Offset
WgdsWiFiSarDeltaGroup1PowerMax2, // Group 1 FCC 5200 Max
WgdsWiFiSarDeltaGroup1PowerChainA2, // Group 1 FCC 5200 A Offset
WgdsWiFiSarDeltaGroup1PowerChainB2, // Group 1 FCC 5200 B Offset
WgdsWiFiSarDeltaGroup2PowerMax1, // Group 2 EC Jap 2400 Max
WgdsWiFiSarDeltaGroup2PowerChainA1, // Group 2 EC Jap 2400 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB1, // Group 2 EC Jap 2400 B Offset
WgdsWiFiSarDeltaGroup2PowerMax2, // Group 2 EC Jap 5200 Max
WgdsWiFiSarDeltaGroup2PowerChainA2, // Group 2 EC Jap 5200 A Offset
WgdsWiFiSarDeltaGroup2PowerChainB2, // Group 2 EC Jap 5200 B Offset
WgdsWiFiSarDeltaGroup3PowerMax1, // Group 3 ROW 2400 Max
WgdsWiFiSarDeltaGroup3PowerChainA1, // Group 3 ROW 2400 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB1, // Group 3 ROW 2400 B Offset
WgdsWiFiSarDeltaGroup3PowerMax2, // Group 3 ROW 5200 Max
WgdsWiFiSarDeltaGroup3PowerChainA2, // Group 3 ROW 5200 A Offset
WgdsWiFiSarDeltaGroup3PowerChainB2, // Group 3 ROW 5200 B Offset
}
})
When read the ACPI data to find out the WGDS, the DATA_SIZE is never
matched.
From the above format, it gives 19 numbers, but our driver is hardcode
as 18.
Fix it to pass then can parse the data into our wgds table.
Then we will see:
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init Sending GEO_TX_POWER_LIMIT
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[0]: chain A = 68 chain B = 69 max_tx_power = 54
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[0]
Band[1]: chain A = 48 chain B = 49 max_tx_power = 70
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[0]: chain A = 51 chain B = 67 max_tx_power = 50
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[1]
Band[1]: chain A = 69 chain B = 70 max_tx_power = 68
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[0]: chain A = 49 chain B = 50 max_tx_power = 48
iwlwifi 0000:01:00.0: U iwl_mvm_sar_geo_init SAR geographic profile[2]
Band[1]: chain A = 52 chain B = 53 max_tx_power = 51
Cc: stable@vger.kernel.org # 4.12+
Fixes: a6bff3cb19 ("iwlwifi: mvm: add GEO_TX_POWER_LIMIT cmd for geographic tx power table")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Logic is there twice, and we'll need a third place
soon for ini dumping. In addition move the dumping
to a function, also to enable reuse.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
chanwidths isn't used now in debugfs-vif.c. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This enables to incorporate more logic in one place.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TDLS discovery response frame is a unicast direct frame to the peer.
Since we don't have a STA for this peer, this frame goes through
iwl_tx_skb_non_sta(). As the result aux_sta and some completely
arbitrary queue would be selected for this frame, resulting in a queue
hang. Fix that by sending such frames through AP sta instead.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW asserts 0x70, 0x71, and 0x73 all just mean that the real error
happened in another MAC, and to look there for the problem. Add their
descriptions to the assert number lookup table so users get a nicer
error message in the logs.
Also, since the 4 most-significant bits of the assert number are
dynamic, and depend on which MAC the assert occurred on, ignore those
bits when looking up the assert name.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The trigger structure is being passed around, when
all we care about is whether to dump only monitor
or not. Pass a bool instead.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code sets the write pointer when getting the TX queue
allocate response. This causes a redundant interrupt with any actual
change in the pointer. Remove this write altogether.
Fixes: 310181ec34 ("iwlwifi: move to TVQM mode")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If tx fails during connection establishment, try another antenna for
the next tx. This will increase the chance to establish connection if
one of the antennas is blocked. Note that the antenna is toggled even
when failing to tx data frames since connection establishment may use
EAPOLs for 802.1X authentication/ 4 way handshake.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the association supports HE, HT/VHT rates will never be used for Tx
and therefore there's no need to set the sgi-per-channel-width-support
bits, so don't set them in this case.
Fixes: 110b32f065 ("iwlwifi: mvm: rs: add basic implementation of the new RS API handlers")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Switch the antenna used for management tx only if previous tx failed.
If previous tx succeeded, there is no reason to switch antennas.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enable low latency for softAP in all modes (standalone, SCM
and DCM).
This is in order to minimize the time the softAP leaves the channel for
other operations
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In D3 suspend flow in 9260 gen2 HW, the NIC receives two PERST signals.
The first PERST is expected and indicates the device on coming resume flow.
The second PERST causes FW restart FW restart.
In order to avoid this issue, the FW set the persistence bit on.
Once this bit is set, the FW ignores reset attempts.
The problem is when the FW gets assert during D3 and then the persistence
bit is set and causes the FW to ignore reset.
To handle this issue, the FW opens the preg bit which allows access
to the persistence bit, so that the driver clear the persistence bit
and reset the NIC.
The flow is as follows:
the driver checks if the persistence bit is set.
If the bit is set, the driver checks if he can clear the bit.
If the driver can not clear the bit then there is no point to continue
configuring the NIC since it will fail.
The fix was added is in start HW flow instead of the resume flow since in
general, if the persistence bit is set, the driver can not start the FW.
So it is good to check it when we start configuring the NIC.
The driver does not need to close the preg bit since the FW close it
during the start flow.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the queue management code runs under mvm->mutex, so there are
only very few cases of accessing the data structures without it:
* TX path, which doesn't take any locks anyway
* iwl_mvm_wake_sw_queue() and iwl_mvm_stop_sw_queue() where we
just (atomically) read a bitmap, so the lock isn't needed.
Therefore, we can remove the spinlock. This enables some cleanup
in the ugly locking in iwl_mvm_inactivity_check().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we mark a TID as no longer having a queue, there's no
guarantee the TX path isn't using this txq_id right now,
having accessed it just before we reset the value. To fix
this, add synchronize_net() when we change the TIDs from
having a queue to not having one, so that we can then be
sure that the TX path is no longer accessing that queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c: In function 'iwl_mvm_rx_mpdu_mq':
drivers/net/wireless/intel/iwlwifi/mvm/rxmq.c:1386:7: warning:
variable 'he_phy_data' set but not used [-Wunused-but-set-variable]
u64 he_phy_data;
'he_phy_data' never used since be introduce in
commit 18ead597da ("iwlwifi: support new rx_mpdu_desc api")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 201384 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The variables il->staging.filter_flags, rxon1->filter_flags and
rxon2->filter_flags need to be protected by the mutex lock il->mutex.
This patch adds a lock assertion of il->mutex to check whether
this lock is held.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rs_rate_from_ucode_rate() function may return -EINVAL if the rate
is invalid, but none of the callsites check for the error, potentially
making us access arrays with index IWL_RATE_INVALID, which is larger
than the arrays, causing an out-of-bounds access. This will trigger
KASAN warnings, such as the one reported in the bugzilla issue
mentioned below.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=200659
Cc: stable@vger.kernel.org
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We don't really need this state: instead of having an inactive
state where we can awaken zombie queues again if needed, just
keep them in their normal state unless a new queue is actually
needed and there's no other way of getting one.
We do this here by making the inactivity check not free queues
unless instructed that we now really need to allocate one to a
specific station, and in that case it'll just free the queue
immediately, without doing any inactivity step inbetween.
The only downside is a little bit more processing in this case,
but the code complexity is lower.
Additionally, this fixes a corner case: due to the way the code
worked, we could only ever reuse an inactive queue if it was
the reserved queue for a station, as iwl_mvm_find_free_queue()
would never consider returning an inactive queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to call iwl_mvm_inactivity_check() from here in the
next patch, so need to move the code down to be able to.
Fix a minor checkpatch complaint while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is only used in the file where it's declared,
so just make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of iterating all the queues after having potentially
changed some queue configurations, rechecking if that was done,
mark the ones that do need a TID change explicitly in a bitmap
and use that to send the change to the firmware.
While at it, also rename iwl_mvm_change_queue_owner() to
iwl_mvm_change_queue_tid() since that's more obvious - the
"kind" of owner isn't immediately clear right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We set the queue to this state, only to pretty much immediately
move it out of it again. However, we can't even hit any of the
code that checks if the queue is reconfiguring, because all of
this happens under mvm->mutex and we hold the all the way from
marking the queue as RECONFIGURING to marking it as READY again.
Additionally, the queue that became RECONFIGURING would've been
in SHARED state before, and it can safely stay in that state. In
case of errors, it previously would have stayed in RECONFIGURING
which it could never have left again.
Remove the state entirely and just track the queues that need to
be reconfigured in a separate, local, bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently reconfigure the queues after the inactivity check,
but only in one of the two callers. This might leave queues in
a state where the TID owner is wrong, if called when reserving
a queue for a new station.
Clean this up and do the reconfiguration inside the inactivity
check function. This requires changing the locking, but one of
the two places already holds the mvm mutex and the other easily
can.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If TVQM is used we skip over this, move the code into a new
function to get rid of the label.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to build a bitmap first and then iterate,
just do the iteration with the right locking directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have a hw refcount if we just mark the
command queue with a (fake) TID; at that point, the refcount
becomes equivalent to the hweight() of the TID bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
None of these functions really need to be separate, they're all
only used in sta.c, move them there and make them static.
Fix a small typo in related code while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make this a named struct rather than an anonymous one,
we'll want to refer to it by name later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the rt status checking to the start of the resume flow in order
to avoid sending D0I3_END_CMD to the FW. Also, collect dump if an
assert was encountered.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops. Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.
Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently in case of DCM with P2P GO where BSS DTIM interval < 220 msec
the fw fails to allocate events for the P2P GO dtim due to long passive
scan events.
Fix this by requesting all scans in this scenario to be fragmented with
fast balance scan time settings. The only exception is in case
fragmented scan was planned to be set due to low latency or high
throughput reason, set the scan timing as planned.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fast balance scan is similar to SCAN_TYPE_MILD, but this scan is
fragmented and has shorter out of operating channel time,
and therefore better match low latency scenarios.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split TX tracing to be per TB. This is needed now that
AMSDUs can be sent and skb can be larger than trace
limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we TX AMSDU, we shouldn't pad the packet. In the past,
we were building AMSDU only in transport layer, and gen2
functions are built based on this. However, now that op mode
may build AMSDUs, we need to take care of padding also in
gen2 "non-pcie-amsdu" path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbua+lAAoJEG4XJFUm622bc74H/3CU3nKceottcybfmdNcxbTj
OHQ6ulu2OJvIrTnKOIe9WWcgoGeoEEKUcEvrV2SjopYUvFR+XPdC0TPKCxmzi020
QQyemogR+EyMx4nDqYkMysACQjTgzym8vKYrYZ5JAf0S12nRkeu4Qhvod6a9bHkO
HJWJekhm2+wIXOb02LoLhsdijhUUlYPcROZCAXlsYf7mpRIgf7PJQURI+yjfiGBW
Z8cGOH7QHU/68b5ExQAgD3OVpI7cTQ3JlE/IM1nM7UozDPRm7ZipW+Q5XJCYwjfU
Yexh1wo8CUSoK2FW5mwJJUaDUfWR5PQMDBjmGXuauFrfIrTIltJpWliEAIFV++c=
=gsaN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.
Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.
The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_txq_build_tfd() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The fall-through to the MVM case is intended as we have to do
*something* to continue, and can't easily clean up. So we'll
just fail in mvm later, if this does happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_gen2_set_tb() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Fixes: ab6c644539 ("iwlwifi: pcie: copy TX functions to new transport")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With NICs that don't read the NVM directly and instead rely on getting
the relevant data from the firmware, the number of reserved MAC
addresses was not added to the API. This caused the driver to assume
there is only one address which results in all interfaces getting the
same address. Update the API to fix this.
While at it, fix-up the comments with firmware api names to actually
match what we have in the firmware.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In mac80211, the default remains for HT, so set the limit to
HE for our driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For SU/SU-ER/MU PPDUs we have spatial reuse.
For those where it's relevant we also know the pre-FEC
padding factor, PE disambiguity bit, beam change bit
and doppler bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add information about the LDCP extra symbol segment to the HE
data when applicable (not for trigger-based PPDUs).
While at it, clean up the code for UL/DL a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This code gets shorter if it doesn't have to check all the
conditions, so move it to an appropriate place that has all
of them validated already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split the code out into a separate routine, and move that to be
called inside the previously introduced iwl_mvm_decode_he_phy_data()
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull some of the decoding of he_phy_data into a separate function so
we don't need to check over and over again if it's valid.
While at it, fix the UL/DL bit reporting to be for all but trigger-
based frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As detected by Luca during code review when I move this in the
next patch, the code here is putting the data into the wrong
field (flags1 instead of flags2). Fix that.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Reported-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove a stray empty line, unbreak some lines that aren't
really that long, and move on variable setting into the
initializer to avoid initializing it twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is equivalent to checking he_phy_data != HE_PHY_DATA_INVAL,
which is already done in a number of places, so remove the extra
'overload' variable entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
queue which means that the worker will not run for now
since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
and that we are now resuming from suspend and cancels
the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
and doesn't really allocate a station ID for the aux
station
17) a new queue is added for the aux station
Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.
Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:
drivers/net/wireless/intel/iwlwifi/pcie/trans.c:2122 iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]()
Timeout waiting for hardware access (CSR_GP_CNTRL 0x080403d8)
Call Trace:
[<ffffffffc03e6ad3>] iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]
[<ffffffffc03e6a13>] iwl_trans_pcie_dump_regs+0x3fd/0x3fd [iwlwifi]
[<ffffffffc03dad42>] iwl_fw_error_dump+0x4f5/0xe8b [iwlwifi]
[<ffffffffc04bd43e>] __iwl_mvm_mac_start+0x5a/0x21a [iwlmvm]
[<ffffffffc04bd6d2>] iwl_mvm_mac_start+0xd4/0x103 [iwlmvm]
[<ffffffffc042d378>] drv_start+0xa1/0xc5 [iwl7000_mac80211]
[<ffffffffc045a339>] ieee80211_reconfig+0x145/0xf50 [mac80211]
[<ffffffffc044788b>] ieee80211_resume+0x62/0x66 [mac80211]
[<ffffffffc0366c5b>] wiphy_resume+0xa9/0xc6 [cfg80211]
The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:
0x00002093 | ADVANCED_SYSASSERT
0x000002F0 | trm_hw_status0
0x00000000 | trm_hw_status1
0x00000B38 | branchlink2
0x0001978C | interruptlink1
0x00000000 | interruptlink2
0xFF080501 | data1
0xDEADBEEF | data2
0xDEADBEEF | data3
Firmware error during reconfiguration - reprobe!
FW error in SYNC CMD SCD_QUEUE_CFG
Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.
Fixes: bf8b286f86 ("iwlwifi: mvm: defer setting IWL_MVM_STATUS_IN_HW_RESTART")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself. Group them in a function to avoid code duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code that dumps various memory types repeats itself. Move it to a
function to avoid duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow the FW to reorder HB channels and first scan HB channels with
assumed APs, in order to reduce the scan duration.
Currently enable it for all scan requests types.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split iwl_fw_error_dump to two parts. The first part will dump the
actual data, and second will do the file allocations, trans calls and
actual file operations. This is done in order to enable reuse of the
code for the new debug ini infrastructure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a macro to replace all the conditions checking for valid dump
length. In addition, move the fifo len calculation to a helper
function.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug variables are bloating the iwl_fw struct. And the fields
are out of order, missing docs and some are redundant.
Clean this up. This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When reading the profiles from the EWRD table in ACPI, we loop over
the data and set it into our internal table. We use the number of
profiles specified in ACPI without checking its validity, so if the
ACPI table is corrupted and the number is larger than our array size,
we will try to make an out-of-bounds access.
Fix this by making sure the value specified in the ACPI table is
valid.
Fixes: 6996490501 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbsgclAAoJEG4XJFUm622bAJ0H/A53eluDpiA6cT2tbThQn/jC
+t9DH6EMR4WpYaBEFZtfbZxgrow2bdbllrfrcq22U8Z9BTg875MunJAureEG8Rkn
mBowkuu/RESOO00JXTuqvGcTP+1oaaETEdyABzQFI3uCDyEF9vGCJwNODtyQ5Rch
JYFVDJhWYm1K84jTCDX1x9izEKxf1PaQobh8JqZnvNG0QOIDpT6y/T5RGhUL9nTr
aRuGDa9ap4RFocq1t0eVqx/NliXOHuEbO58E6rMm9DiSujmf1Wa/tndNXGxGWk/N
X8KCz619Syr3v/lF6gXWwmsHt5TBh+peKajUsVY9wJUYkBFTOzVjy0ucYCr67yA=
=HZJ3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.19
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbs6LVAAoJEG4XJFUm622b0sAH/1WLU433ZipgULs6PLULDz3/
cFS4CSu9+Hewx9MKvdr+vgMoru70CkiFIZMJeo/oNqAtFb6TQhXPFz2Ci3K4Y6jK
yZKATh9PvzQrOGQ1iy4p8QK6bQ9WRUNY5+elJuNQH62oB/SZ0XqCMU8ujUQRSaTC
xVqfIRnAtKcchAm/nqxx+EwlGCiUmlyt2pw2IUXXABLW7Fkj3Z3ISlOd8xVW6tca
XyWlx9pjZOrFrgOzyORB/B4TNI5q5CdcYPg2DEpqOs6LQeGXEq4BSxfxCe2de4ku
St6417K0OFTbUTZS7kJaxJnQFd1ZWhDtj5cJUzdNsSVzqeYeJoTnR4FBqDWLlec=
=7Nmq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
-----BEGIN PGP SIGNATURE-----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=5Y2V
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-09-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second set of iwlwifi patches for 4.20
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: remove
extraneous parentheses around the comparison to silence this warning
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~ ^ ~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: use '=' to
turn this equality comparison into an assignment
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/134
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support for setting keys for TKIP cipher suite was mistakenly removed
for AP mode. Fix this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The capability bit was added to the driver and had been negotiated
with the firmware, but then got forgotten in the firmware and later
reused for a different capability. Now the firmware added it in a
new bit.
Fixes: 2eabc84d2f ("iwlwifi: mvm: only send LEDS_CMD when the FW supports it")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As a temporary stage in the 22560 devices bring up, we disabled
power save, to avoid bugs related to that domain.
Now we would like to use power save so enable the balanced mode,
and allow configuring the mode via module parameter.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future devices we will have more than one debug buffer.
Prepare the infrastructure for allocation and release of
multiple debug buffers by grouping the variables in an array
of structures and moving it to trans section, where they will
be visible to opmode and FW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to be able to build A-MSDUs in higher layers, e.g. by
xmit_more, so support transmitting SKBs with fraglist to use
it for such.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We no longer want to consider the RSSI if the beacon / probe
has been heard on an adjacent channel.
This was based on a firmware capability that is now
unavailable.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires setting the non-shared antenna
for the single_stream_ant_msk field in the TLC command.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
