Use of_device_get_match_data() helper to get the match-data.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Link: https://lore.kernel.org/r/20210114152700.21916-2-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
GL9763E enters ASPM L1 state after a very short idle in default,
even during a burst of request. So the R/W performance of GL9763E
is low with some platforms, which support ASPM mechanism, due to
entering ASPM L1 state very frequently in R/W process. Set the L1
entry delay bits in vendor-specific register to 0x3FF to enlarge
the idle period to 260us for improving the R/W performance
of GL9763E.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210115054736.27769-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support for the controller present on the AM64x SoC.
There are instances:
sdhci0: 8bit bus width, max 400 MBps
sdhci1: 4bit bus width, max 100 MBps
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210113115908.3882-3-a-govindraju@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make sure voltage is below 0.5V before power on during a power cycle,
add a delay of at least 100ms. The delays in the mmc core is not sufficient
for the rtsx pci device.
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20210113105723.7916-1-ricky_wu@realtek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the device suspend process begins before the mmc host's autosuspend
timeout, the host will continue running during system sleep. Avoid
this by forcing runtime suspend during a global suspend transition.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20210113052421.36553-1-samuel@sholland.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds new compatible string to differentiate
between the controllers versions included in the AP807
north bridge. Thanks to this change, the SoCs which use
AP807 will not run unintentionally in the 'slow mode'
with disabled UHS modes.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210112094655.12274-3-kostap@marvell.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change code style of mapping the syscon in sdhci_arasan_update_support64b()
for readability and consistency.
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210111155001.12307-3-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
introduces syscon map sdhci_arasan_update_support64b(). Unfortunately,
kernel-doc format script tool has not been run before and causing warning
on the documentation style.
Below is the output when running the kernel-doc script tool:
drivers/mmc/host/sdhci-of-arasan.c:1388: warning: contents before sections
Let's fix this by using standard conventions kernel-doc format.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20210111155001.12307-2-muhammad.husaini.zulkifli@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a vendor-specific bit named GLI_9763E_MB_ERP_ON at the bit7 of
register 888h to decide whether to enhance random R/W performance
of GL9763E. CQHCI support will be enabled if and only if the bit is
set and the GLI_9763E_MB_CMQ_OFF bit is not set.
Signed-off-by: Renius Chen <reniuschengl@gmail.com>
Link: https://lore.kernel.org/r/20210106085332.5494-1-reniuschengl@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the datasheet, this controller needs retune when
cmd or data timeout happens. So, add a condition into .check_retune().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Currently, busy timeout is not checked for data transfer command. But,
if the temperature condition changes, the data cannot be acquired
correctly and timeout may occur. Also, we could reproduce an issue by
using mmc_test driver (e.g. "Correct xfer_size at write (start
failure)"). Therefore, this adds timeout error check.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rework commit message.]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: rebase, add commit description]
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608708622-29668-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable SGDMA support for SD_IO_RW_EXTENDED and add proper check
for scatterlist size alignment in block mode.
According to documentation, in SDIO block mode meson-gx DMA could
only handle buffers with sizes that are multiples of SDIO block size.
Some SDIO drivers like brcmfmac use scatterlist API, but do not enforce
proper scatterlist buffer size alignemnt, this looks like a root cause
of non-working CMD53.
Some minor style fixes.
Signed-off-by: Dmitry Lebed <lebed.dmitry@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201218075312.67338-1-lebed.dmitry@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when get request SW timeout, if CMD/DAT xfer done irq coming right now,
then there is race between the msdc_request_timeout work and irq handler,
and the host->cmd and host->data may set to NULL in irq handler. also,
current flow ensure that only one path can go to msdc_request_done(), so
no need check the return value of cancel_delayed_work().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201218071611.12276-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add pre_req and post_req support to improve performance.
Inspired by a patch in the BSP by Masaharu Hayakawa.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
According to the latest datasheet, the internal DMAC buffer alignment
R-Car Gen3 SDHI HW should be 128-bytes. So, fix it.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[shimoda: revise commit description, rebase]
Fixes: 2a68ea7896 ("mmc: renesas-sdhi: add support for R-Car Gen3 SDHI DMAC")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1608114572-1892-2-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MSM SDHCI driver always set the "actual_clock" field to 0. It had
a comment about it not being needed because we weren't using the
standard SDHCI divider mechanism and we'd just fallback to
"host->clock". However, it's still better to provide the actual
clock. Why?
1. It will make timeout calculations slightly better. On one system I
have, the eMMC requets 200 MHz (for HS400-ES) but actually gets 192
MHz. These are close, but why not get the more accurate one.
2. If things are seriously off in the clock driver and it's missing
rates or picking the wrong rate (maybe it's rounding up instead of
down), this will make it much more obvious what's going on.
NOTE: we have to be a little careful here because the "actual_clock"
field shouldn't include the multiplier that sdhci-msm needs
internally.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/20201214092048.v5.2.I7564620993acd4baa63fa0e3925ca879a86d3ee3@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As talked about in commit 5e4b7e82d4 ("clk: qcom: gcc-sdm845: Use
floor ops for sdcc clks"), most clocks handled by the Qualcomm clock
drivers are rounded _up_ by default instead of down. We should make
sure SD/MMC clocks are always rounded down in the clock drivers.
Let's add a warning in the Qualcomm SDHCI driver to help catch the
problem.
This would have saved a bunch of time [1].
NOTE: this doesn't actually fix any problems, it just makes it obvious
to devs that there is a problem and that should be an indication to
fix the clock driver.
[1] http://lore.kernel.org/r/20201210102234.1.I096779f219625148900fc984dd0084ed1ba87c7f@changeid
Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201214092048.v5.1.Iec3430c7d3c2a29262695edef7b82a14aaa567e5@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch adds support for A100 MMC controller, which use word address
for internal dma.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Link: https://lore.kernel.org/r/20201211011934.6171-10-andre.przywara@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDHCI_PRESET_FOR_* registers are not set(all read as zeros), so
set the quirk.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20201210165510.76b917e5@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A call to 'ausdhi6_dma_release()' to undo a previous call to
'usdhi6_dma_request()' is missing in the error handling path of the probe
function.
It is already present in the remove function.
Fixes: 75fa9ea6e3 ("mmc: add a driver for the Renesas usdhi6rol0 SD/SDIO host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201217210922.165340-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'sdhci_remove_host()' and 'sdhci_pltfm_free()' should be used in place of
'mmc_remove_host()' and 'mmc_free_host()'.
This avoids some resource leaks, is more in line with the error handling
path of the probe function, and is more consistent with other drivers.
Fixes: fb8bd90f83 ("mmc: sdhci-sprd: Add Spreadtrum's initial host controller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Orson Zhai <orson.zhai@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201217204236.163446-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'dma_request_chan()' calls should be balanced by a corresponding
'dma_release_channel()' call.
Add the missing call both in the error handling path of the probe function
and in the remove function.
Fixes: ff65ffe46d ("mmc: Add Actions Semi Owl SoCs SD/MMC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20201209194202.54099-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The implementation of sdhci_pltfm_suspend() is only available when
CONFIG_PM_SLEEP is set, which triggers a linking error:
"undefined symbol: sdhci_pltfm_suspend" when building sdhci-brcmstb.c.
Fix this by implementing the missing stubs when CONFIG_PM_SLEEP is unset.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 5b191dcba7 ("mmc: sdhci-brcmstb: Fix mmc timeout errors on S5 suspend")
Cc: stable@vger.kernel.org
Tested-By: Nicolas Schichan <nschichan@freeebox.fr>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
that added a shutdown callback to the diver, is causing "mmc timeout"
errors on S5 suspend. The problem was that the "remove" was queuing
additional MMC commands after the "shutdown" and these caused
timeouts as the MMC queues were cleaned up for "remove". The
shutdown callback will be changed to calling sdhci-pltfm_suspend
which should get better power savings because the clocks will be
shutdown.
Fixes: e7b5d63a82 ("mmc: sdhci-brcmstb: Add shutdown callback")
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210107221509.6597-1-alcooperx@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Automatic Clock Gating is a feature used for the power consumption
optimisation. It turned out that during early init phase it may prevent the
stable voltage switch to 1.8V - due to that on some platforms an endless
printout in dmesg can be observed: "mmc1: 1.8V regulator output did not
became stable" Fix the problem by disabling the ACG at very beginning of
the sdhci_init and let that be enabled later.
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Cc: stable@vger.kernel.org
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201211141656.24915-1-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for
RPMB") began to use ACMD23 for RPMB if the host supports ACMD23. In
RPMB ACM23 case, we need to set bit 31 to CMD23 argument, otherwise
RPMB write operation will return general fail.
However, no matter V4 is enabled or not, the dwcmshc's ARGUMENT2
register is 32-bit block count register which doesn't support stuff
bits of CMD23 argument. So let's handle this specific ACMD23 case.
From another side, this patch also prepare for future v4 enabling
for dwcmshc, because from the 4.10 spec, the ARGUMENT2 register is
redefined as 32bit block count which doesn't support stuff bits of
CMD23 argument.
Fixes: a44f7cb937 ("mmc: core: use mrq->sbc when sending CMD23 for RPMB")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201229161625.38255233@xhacker.debian
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements.
-----BEGIN PGP SIGNATURE-----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=1A/T
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Initial support for SD express card/host
MMC host:
- mxc: Convert the driver to DT-only
- mtk-sd: Add HS400 enhanced strobe support
- mtk-sd: Add support for the MT8192 SoC variant
- sdhci-acpi: Allow changing HS200/HS400 driver strength for AMDI0040
- sdhci-esdhc-imx: Convert the driver to DT-only
- sdhci-pci-gli: Improve performance for HS400 mode for GL9763E
- sdhci-pci-gli: Reduce power consumption for GL9755
- sdhci-xenon: Introduce ACPI support
- tmio: Fix command error processing
- tmio: Inform the core about the max_busy_timeout
- tmio/renesas_sdhi: Support custom calculation of busy-wait time
- renesas_sdhi: Reset SCC only when available
- rtsx_pci: Add SD Express mode support for RTS5261
- rtsx_pci: Various fixes and improvements for RTS5261
MEMSTICK:
- Minor fixes/improvements"
* tag 'mmc-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (72 commits)
dt-bindings: mmc: eliminate yamllint warnings
mmc: sdhci-xenon: introduce ACPI support
mmc: sdhci-xenon: use clk only with DT
mmc: sdhci-xenon: switch to device_* API
mmc: sdhci-xenon: use match data for controllers variants
dt-bindings: mmc: Fix xlnx,mio-bank property values for arasan driver
mmc: renesas_sdhi: populate hook for longer busy_wait
mmc: tmio: add hook for custom busy_wait calculation
mmc: tmio: set max_busy_timeout
dt-bindings: mmc: imx: fix the wrongly dropped imx8qm compatible string
mmc: sdhci-pci-gli: Disable slow mode in HS400 mode for GL9763E
mmc: sdhci: Use more concise device_property_read_u64
memstick: r592: Fix error return in r592_probe()
mmc: mxc: Convert the driver to DT-only
mmc: mxs: Remove the unused .id_table
mmc: sdhci-of-arasan: Fix fall-through warnings for Clang
mmc: sdhci-pci-gli: Reduce power consumption for GL9755
mmc: mediatek: depend on COMMON_CLK to fix compile tests
mmc: pxamci: Fix error return code in pxamci_probe
mmc: sdhci: Update firmware interface API
...
Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be more
and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iDZA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylRMACgqxKS2CUcY8tPnR5weHEsbz6O+KAAn3BtEFnK
7V9EnSuZe4L1jNOHOB5V
=xzHh
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big char/misc driver update for 5.11-rc1.
Continuing the tradition of previous -rc1 pulls, there seems to be
more and more tiny driver subsystems flowing through this tree.
Lots of different things, all of which have been in linux-next for a
while with no reported issues:
- extcon driver updates
- habannalab driver updates
- mei driver updates
- uio driver updates
- binder fixes and features added
- soundwire driver updates
- mhi bus driver updates
- phy driver updates
- coresight driver updates
- fpga driver updates
- speakup driver updates
- slimbus driver updates
- various small char and misc driver updates"
* tag 'char-misc-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (305 commits)
extcon: max77693: Fix modalias string
extcon: fsa9480: Support TI TSU6111 variant
extcon: fsa9480: Rewrite bindings in YAML and extend
dt-bindings: extcon: add binding for TUSB320
extcon: Add driver for TI TUSB320
slimbus: qcom: fix potential NULL dereference in qcom_slim_prg_slew()
siox: Make remove callback return void
siox: Use bus_type functions for probe, remove and shutdown
spmi: Add driver shutdown support
spmi: fix some coding style issues at the spmi core
spmi: get rid of a warning when built with W=1
uio: uio_hv_generic: use devm_kzalloc() for private data alloc
uio: uio_fsl_elbc_gpcm: use device-managed allocators
uio: uio_aec: use devm_kzalloc() for uio_info object
uio: uio_cif: use devm_kzalloc() for uio_info object
uio: uio_netx: use devm_kzalloc() for or uio_info object
uio: uio_mf624: use devm_kzalloc() for uio_info object
uio: uio_sercos3: use device-managed functions for simple allocs
uio: uio_dmem_genirq: finalize conversion of probe to devm_ handlers
uio: uio_dmem_genirq: convert simple allocations to device-managed
...
Previous patches dropped the strict dependency on the OF_*
in the sdhci-xenon driver. As a result the ACPI support
can be introduced (except for the XENON_A3700 variant)
by adding the necessary ID's in the acpi_match_table.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-5-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a preparation for supporting ACPI, modify the driver
to use the clk framework only when booting with DT -
otherwise rely on the configuration done by firmware.
For that purpose introduce also a custom SDHCI get_max_clock
callback.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-4-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In order to support both ACPI and DT, modify the driver
to use device_* routines for obtaining the properties
values.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-3-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As a part of the ACPI support preparation resign from checking
compatible strings in the driver. Instead of that use a new
enum and assign the values to match data accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/20201204171626.10935-2-mw@semihalf.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
rtsx_pcr:
add callback functions to support runtime PM
add delay_work to put device to D3 after idle
over 10 sec
rts5249:
add extra init flow for rtd3 and set rtd3_en from
config setting
rtsx_pci_sdmmc:
child device support autosuspend
Signed-off-by: Ricky Wu <ricky_wu@realtek.com>
Link: https://lore.kernel.org/r/20201202065857.19412-1-ricky_wu@realtek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The #ifdef check for the suspend/resume functions is wrong:
drivers/mmc/host/mtk-sd.c:2765:12: error: unused function 'msdc_suspend' [-Werror,-Wunused-function]
static int msdc_suspend(struct device *dev)
drivers/mmc/host/mtk-sd.c:2779:12: error: unused function 'msdc_resume' [-Werror,-Wunused-function]
static int msdc_resume(struct device *dev)
Remove the #ifdef and mark all four as __maybe_unused to aovid the
problem.
Fixes: c0a2074ac5 ("mmc: mediatek: Fix system suspend/resume support for CQHCI")
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201203222922.1067522-1-arnd@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of the EXTOP bit in R-Car Gen3 SoCs to have a twice as large
busy wait duration.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Newer SDHI variants can 'wait while busy' longer than the generic TMIO.
Provide a hook to get the maximum cycle count to wait for. If the hook
is not populated, fall back to a generic version which works well with
all older TMIO/SDHI variants.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Set max_busy_timeouts for variants known to support the TOPxx bits in
the SD_OPTION register. The timeout mechanism was running in the
background but not yet properly handled in the driver. So, let the MMC
core know when to not use R1B to avoid unhandled timeouts.
My datasheets for older variants (tmio_mmc.c) suggest that they support
it, too. However, actual bit descriptions are lacking, so I chose an
opt-in approach.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Further testing of error cases revealed that downgrade is not enough, so
we need to reset the SCC which is done by calling the custom reset
function. This reset function can distinguish between the various SDHI
variants, so protecting the call with MIN_RCAR2 is enough here.
Fixes: 24ce2d7b8b ("mmc: tmio: bring tuning HW to a sane state with MMC_POWER_OFF")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125204953.3344-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The GL9763E uses 150Mhz (slow mode) by default in HS400 mode. In order
to make HS400 mode run at 200Mhz, the slow mode needs to be turned off.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201125110145.2824-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since we only need a single u64 the _array form is
unnecessarily. Use device_property_read_u64 instead.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201125033630.603863-1-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123203004.18792-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mxs-mmc driver is only used by DT platforms and the .id_table
is unused.
Get rid of it to simplify the code.
While at it, use of_device_get_match_data() to retrieve the driver
data.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123191956.10542-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For GL9755, reduce power consumption by lowering the LFCLK and disabling
the DMACLK on low-power.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201123053702.6083-1-benchuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MFD_OMAP_USB_HOST uses Common Clock Framework thus it cannot be
built on platforms without it (e.g. compile test on MIPS with LANTIQ):
mips-linux-ld: drivers/mmc/host/mtk-sd.o: in function `msdc_ops_set_ios':
mtk-sd.c:(.text+0x2bbc): undefined reference to `clk_get_parent'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201122120056.100045-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return the error code from devm_gpiod_get_optional() instaed
of 0 in pxamci_probe().
Fixes: f54005b508 ("mmc: pxa: Use GPIO descriptor for power")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Link: https://lore.kernel.org/r/20201121021431.3168506-1-chengzhihao1@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The device_* calls were added a few years ago to abstract
DT/ACPI/fwnode firmware interfaces. Lets convert the two
sdhci caps fields to use the generic calls rather than the OF
specific ones. This has the side effect of allowing
ACPI based devices to quirk themselves when the caps field
is broken.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Link: https://lore.kernel.org/r/20201120233831.447365-1-jeremy.linton@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 16ada730a7 ("mmc: sdhci-of-arasan: Modify clock operations
handling") introduced support for platform specific clock operations.
Around the same point in time the commit 36c6aadaae ("mmc:
sdhci-of-arasan: Add support for Intel Keem Bay") was also merged.
Unfortunate it was not really tested on top of the previously mentioned
commit, which causes clock registration failures for Keem Bay SOC devices.
Let's fix this, by properly declaring the clock operation for Keem Bay SOC
devices.
Fixes: 36c6aadaae ("mmc: sdhci-of-arasan: Add support for Intel Keem Bay")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201118120120.24908-2-muhammad.husaini.zulkifli@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SDIO recheck fix is required for more of the supported variants. Let's
add it to those that needs it.
Reported-by: Fabien Parent <fparent@baylibre.com>
Reported-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Link: https://lore.kernel.org/r/20201119030237.9414-1-yong.mao@mediatek.com
Fixes: 9e2582e574 ("mmc: mediatek: fix SDIO irq issue")
Cc: stable@vger.kernel.org
[Ulf: Clarified commitmsg ]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mmc/host/sdhci-st.c:512:34: warning:
‘st_sdhci_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201120162344.485921-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mmc/host/sdhci-sprd.c:723:34: warning:
‘sdhci_sprd_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20201120162344.485921-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If some errors are detected at the same time as the access end
interrupt, the access end interrupt was not cleared. Especially with
DMA, because then the access end interrupt was never enabled and, thus,
never cleared. Clear the interrupt register always when a command error
occurs.
Signed-off-by: Masaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[saito: rebase to v5.4]
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
[wsa: rebase and extension of the commit message]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201117131337.35307-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20201117113750.25053-1-festevam@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Printing kernel pointers is discouraged because they might leak kernel
memory layout. This fixes smatch warning:
drivers/mmc/host/tmio_mmc.c:177 tmio_mmc_probe() warn: argument 3 to %08lx specifier is cast from pointer
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201116164252.44078-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'busy_timeout' is in msecs, not in jiffies. Use the correct factor.
Fixes: 5e958e4aac ("sdhci: tegra: Implement Tegra specific set_timeout callback")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20201116132206.23518-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In the current implementation DLL reset will be issued for
each ITAP and OTAP setting inside ATF, this is creating issues
in some scenarios and this sequence is not inline with the TRM.
To fix the issue, DLL reset should be removed from the ATF and
host driver will request it explicitly.
This patch update host driver to explicitly request for DLL reset
before ITAP (assert DLL) and after OTAP (release DLL) settings.
Fixes: a5c8b2ae2e ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-4-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Mask the ITAP and OTAP delay bits before updating with the new
tap value for Versal platform.
Fixes: 1a470721c8 ("sdhci: arasan: Add support for Versal Tap Delays")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-3-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Allow configuring the Output and Input tap values with zero to avoid
failures in some cases (one of them is SD boot mode) where the output
and input tap values may be already set to non-zero.
Fixes: a5c8b2ae2e ("mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup")
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1605515565-117562-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Detect if tassadar_dll is required by using core version rather than
just specifying it in the sdhci_msm_variant_info.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Reviewed-by: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Link: https://lore.kernel.org/r/20201112173636.360186-1-dmitry.baryshkov@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
A UHS setting of SDR25 can give better results for High Speed mode.
This is because there is no setting corresponding to high speed. Currently
SDHCI sets no value, which means zero which is also the setting for SDR12.
There was an attempt to change this in sdhci.c but it caused problems for
some drivers, so it was reverted and the change was made to sdhci-brcmstb
in commit 2fefc7c5f7 ("mmc: sdhci-brcmstb: Fix incorrect switch to HS
mode"). Several other drivers also do this.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v5.4+
Link: https://lore.kernel.org/r/20201112133656.20317-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It should use mmc_free_host to free mem in error patch of
msdc_drv_probe.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Liang <zhengliang6@huawei.com>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Link: https://lore.kernel.org/r/20201112092530.32446-1-zhengliang6@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Use a macro to name the hardcoded values. Also, move the SDIF register
definition into the SDHI driver because this is an SDHI extension.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201111100244.15823-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
HOST_MODE should have a CTL_ prefix, too. This makes the code more
readable because we immediately know what it is. Also, remove the
hardcoded values with something readable, too.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201111100244.15823-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All previously called functions handle SCLKEN on their own, no need to
enable it again in sdhi_reset().
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110162151.37622-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no user of renesas_sdhi_reset_scc() anymore, only
renesas_sdhi_disable_scc() so merge these functions into one. I guess
the seperation was cruft anyhow. The BSP doesn't have it anymore and I
can't recall the reason we had it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110162151.37622-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We want to clear TAPEN in a software reset, too, to have a completely
known state. Especially when we doing the initial reset during boot to
clear previous firmware states.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110162151.37622-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'reset' pointer is only populated for Gen2+. So, we don't need to
check for that flag inside the routine.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-5-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The SCC pointer is currently filled whenever the SoC is Gen2+. This is
wrong because there is a Gen2-variant without SCC (SDHI_VER_GEN2_SDR50).
We have been lucky because the writes to unintended registers have not
caused problems so far. But further refactoring work exposed the
problem. So, move the pointer initialization to the place where we know
that the SDHI instance supports tuning. And also populate the 'reset'
pointer unconditionally to make sure the interrupt enable register is
always properly set for Gen2+.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Setting up the SCC parameters does not need a probed TMIO device. But in
the near future, probing the TMIO device needs the SCC parameters setup.
So, fix the ordering.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only re-initialize SCC and tuning when an SCC was found during probe().
This is currently a noop because all R-Car Gen2+ are considered to have
an SCC. But this will change in a later patch, so we need this
preparation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
pic32_sdhci_probe_platform() always returned 0, so there's no reason for
a return value. In addition, pic32_sdhci_probe() checked the return value
for possible error which is unnecessary.
Convert pic32_sdhci_probe_platform() to a void function and remove the
return value check. Fix the following Coccinelle warning:
./drivers/mmc/host/sdhci-pic32.c:127:5-8: Unneeded variable: "ret". Return "0" on line 137
Reported-by: Tosk Robot <tencent_os_robot@tencent.com>
Signed-off-by: Kaixu Xia <kaixuxia@tencent.com>
Link: https://lore.kernel.org/r/1604847648-13036-1-git-send-email-kaixuxia@tencent.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/mmc/host/meson-gx-mmc.c:1252:34: warning:
‘meson_mmc_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201103163046.14336-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch add test mode for RTS5261.
If test mode is set, reader will switch to SD Express mode
mandatorily, and this mode is used by factory testing only.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/1604397269-2780-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/1604278337-55624-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The code has been in a irq-disabled context since it is hard IRQ. There
is no necessity to do it again.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/1604375323-33556-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
RTS5261 support SD mode and PCIe/NVMe mode. The workflow is as follows.
1.RTS5261 work in SD mode and set MMC_CAPS2_SD_EXP flag.
2.If card is plugged in, Host send CMD8 to ask card's PCIe availability.
3.If the card has PCIe availability and WP is not set, init_sd_express() will be invoked,
RTS5261 switch to PCIe/NVMe mode.
4.Mmc driver handover it to NVMe driver.
5.If card is unplugged, RTS5261 will switch to SD mode.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Link: https://lore.kernel.org/r/1603936703-3403-1-git-send-email-rui_feng@realsil.com.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MT8192 msdc is an independent sub system, we need control more bus
clocks for it.
Add support for the additional subsys clocks to allow it to be
configured appropriately.
Signed-off-by: Wenbin Mei <wenbin.mei@mediatek.com>
Reviewed-by: Nicolas Boichat <drinkcat@chromium.org>
Link: https://lore.kernel.org/r/20201014030846.12428-5-wenbin.mei@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change will allow platform designers better control over signal
integrity by allowing them to tune the HS200 and HS400 driver strengths.
The driver strength was previously hard coded to A to solve boot
problems with certain platforms. This driver strength does not
universally apply to all platforms so we need a knob to adjust it.
All older platforms currently have the SDR104 preset hard coded to A in
the firmware. This means that switching from the hard coded value in
the kernel to reading the SDR104 preset is a no-op for these platforms.
Newer platforms will have properly set presets. So this change will
support both new and old platforms.
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Victor Ding <victording@google.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201027084612.528301-1-victording@google.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver can match only via DT table so it should be always used and
the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant for sunxi). This
fixes compile warning:
drivers/mmc/host/sunxi-mmc.c:1181:34: warning: ‘sunxi_mmc_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20201026153810.89512-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver uses GPIO Descriptor Consumer Interface so include proper
header to fix compile test errors like:
drivers/mmc/host/s3cmci.c: In function ‘s3cmci_check_sdio_irq’:
drivers/mmc/host/s3cmci.c:304:7: error:
implicit declaration of function ‘gpiod_get_value’; did you mean ‘gpio_get_value’? [-Werror=implicit-function-declaration]
drivers/mmc/host/s3cmci.c: In function ‘s3cmci_probe_pdata’:
drivers/mmc/host/s3cmci.c:1451:19: error:
implicit declaration of function ‘devm_gpiod_get_index’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201026153810.89512-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This reverts commit db1af1e971. It was
only a workaround to hide a regression. We now have proper fixes.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When powering off a card, we need to disable the tuning HW (like SCC for
the Renesas SDHI) to get to a sane state and allow for re-tuning new
cards. This was hidden before because we wrongly did that in hw_reset()
before which was an unintended use of hw_reset(). Now that we corrected
the use of hw_reset() meanwhile, we revealed this shortcoming and need
to fix it properly by explicitly calling the downgrade callback.
Fixes: 6e7d4de108 ("mmc: renesas_sdhi: move wrong 'hw_reset' to 'reset'")
Suggested-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Reviewed-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When applying a revert, the assumption that DMA only needs to be cleared
in specific cases was wrong. We want to reset the DMA controller every
time the rest of the HW gets reset, too.
Fixes: 34e3211e54 ("Revert "mmc: tmio: fix reset operation"")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201106072549.1495-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 94b110aff8 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
added tmio_mmc_host_free(), but missed the function calling in
the sh_mobile_sdhi_remove() at that time. So, fix it. Otherwise,
we cannot rebind the sdhi/mmc devices when we use aliases of mmc.
Fixes: 94b110aff8 ("mmc: tmio: add tmio_mmc_host_alloc/free()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1604654730-29914-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- sdhci: Fix performance regression with auto CMD auto select
- sdhci-of-esdhc: Fix initialization for eMMC HS400 mode
- sdhci-of-esdhc: Fix timeout bug for tuning commands
-----BEGIN PGP SIGNATURE-----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=LDSp
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC host fixes from Ulf Hansson:
- sdhci: Fix performance regression with auto CMD auto select
- sdhci-of-esdhc: Fix initialization for eMMC HS400 mode
- sdhci-of-esdhc: Fix timeout bug for tuning commands
* tag 'mmc-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-of-esdhc: make sure delay chain locked for HS400
mmc: sdhci-of-esdhc: set timeout to max before tuning
mmc: sdhci: Use Auto CMD Auto Select only when v4_mode is true
For eMMC HS400 mode initialization, the DLL reset is a required step
if DLL is enabled to use previously, like in bootloader.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20201020081116.20918-1-yangbo.lu@nxp.com
Fixes: 54e08d9a95 ("mmc: sdhci-of-esdhc: add hs400 mode support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
On rare occations there is the following error:
mmc0: Tuning timeout, falling back to fixed sampling clock
There are SD cards which takes a significant longer time to reply to the
first CMD19 command. The eSDHC takes the data timeout value into account
during the tuning period. The SDHCI core doesn't explicitly set this
timeout for the tuning procedure. Thus on the slow cards, there might be
a spurious "Buffer Read Ready" interrupt, which in turn triggers a wrong
sequence of events. In the end this will lead to an unsuccessful tuning
procedure and to the above error.
To workaround this, set the timeout to the maximum value (which is the
best we can do) and the SDHCI core will take care of the proper timeout
handling.
Fixes: ba49cbd093 ("mmc: sdhci-of-esdhc: add tuning support")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201022222337.19857-1-michael@walle.cc
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-of-dwcmshc meets an eMMC read performance regression with below
command after commit 427b6514d0 ("mmc: sdhci: Add Auto CMD Auto
Select support"):
dd if=/dev/mmcblk0 of=/dev/null bs=8192 count=100000
Before the commit, the above command gives 120MB/s
After the commit, the above command gives 51.3 MB/s
So it looks like sdhci-of-dwcmshc expects Version 4 Mode for Auto
CMD Auto Select. Fix the performance degradation by ensuring v4_mode
is true to use Auto CMD Auto Select.
Fixes: 427b6514d0 ("mmc: sdhci: Add Auto CMD Auto Select support")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201015174115.4cf2c19a@xhacker.debian
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After the conversions of the reset routines, re-inserting SD cards
didn't work anymore. Apply this temporary workaround to have working SD
cards during the merge window. The issue will be fixed properly until
the final release.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20201008092533.76588-1-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add CQHCI initialization and implement CQHCI operations for GL9763E.
Use bit19 of the register (0x888) to decide whether to disable command
queuing. If the bit is set, the command queuing will be disabled.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Link: https://lore.kernel.org/r/20201005105509.11343-1-ben.chuanggli@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This change fixes HS400 tuning for devices with invalid presets.
SDHCI presets are not currently used for eMMC HS/HS200/HS400, but are
used for DDR52. The HS400 retuning sequence is:
HS400->DDR52->HS->HS200->Perform Tuning->HS->HS400
This means that when HS400 tuning happens, we transition through DDR52
for a very brief period. This causes presets to be enabled
unintentionally and stay enabled when transitioning back to HS200 or
HS400. Some firmware has invalid presets, so we end up with driver
strengths that can cause I/O problems.
Fixes: 34597a3f60 ("mmc: sdhci-acpi: Add support for ACPI HID of AMD Controller with HS400")
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200928154718.1.Icc21d4b2f354e83e26e57e270dc952f5fe0b0a40@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-6-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
With this addition, make sure that DLL is always switched off at the
beginning of the set_clock() call to simplify configuration. This also
removes the need for the dll_on member in struct sdhci_am654_data.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Link: https://lore.kernel.org/r/20200923105206.7988-5-faiz_abbas@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The bit ESDHC_PERIPHERAL_CLK_SEL to select using peripheral clock
or platform clock is not able to be reset by SDHCI_RESET_ALL.
So driver needs to initialize it as 1 or 0 once, to override the
different value which may be configured in bootloader.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200927082304.9232-1-yangbo.lu@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on
Intel GLK"), disabled command-queuing on Intel GLK based LENOVO models
because of it being broken due to what is believed to be a bug in
the BIOS.
It seems that the BIOS of some IRBIS models, including the IRBIS NB111
model has the same issue, so disable command queuing there too.
Fixes: bedf9fc01f ("mmc: sdhci: Workaround broken command queuing on Intel GLK")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=209397
Reported-and-tested-by: RussianNeuroMancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200927104821.5676-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The struct of_device_id is not defined with !CONFIG_OF so its forward
declaration should be hidden to as well. This should address clang
compile warning:
drivers/mmc/host/sdhci-s3c.c:464:34: warning: tentative array definition assumed to have one element
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200925072532.10272-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'struct mmc_host *mmc' comes from drvdata set at the end of probe,
so it cannot be NULL. The code already dereferences it few lines before
the check with mmc_priv(). This also fixes smatch warning:
drivers/mmc/host/moxart-mmc.c:692 moxart_remove() warn: variable dereferenced before check 'mmc' (see line 688)
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200923153739.30327-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC core has now a generic check if some tuning is in progress. Its
protected area is a bit larger than the custom one in this driver but we
concluded that this works equally well for the intended case. So, drop
the local flag and switch to the generic one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200922172253.4458-1-wsa@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MediaTek MMC driver uses pointer to get from private
msdc_host structure to the generic mmc_host structure.
However mmc_host always precedes msdc_host in memory so compute
its address with a subtraction (which is cheaper than a dereference)
using mmc_from_priv() and drop the extra pointer.
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Link: https://lore.kernel.org/r/20200917192624.548720-1-ameynarkhede03@gmail.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If CONFIG_NO_DMA=y (e.g. Sun-3 allmodconfig):
drivers/mmc/host/mmc_spi.c:1323:15: warning: return type defaults to ‘int’ [-Wreturn-type]
static inline mmc_spi_dma_alloc(struct mmc_spi_host *host) { return 0; }
^~~~~~~~~~~~~~~~~
Fix this by adding the missing return type.
Fixes: a395acf0f6 ("mmc: mmc_spi: Allow the driver to be built when CONFIG_HAS_DMA is unset")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/20200914094243.3912-1-geert@linux-m68k.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/890ae5601594fca5de104695a682f4b6efbc631b.1599660554.git.viresh.kumar@linaro.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some R-Car Gen3 SoCs need some manual correction of timing parameters
after the automatic tuning has finished but before next CMD13 is
completed. This patch implements that by this state machine:
- introducing a per-SoC correction table if needed
- iff such a table exists, the 'fixup_request' callback is populated
during probe
- iff such a table exists, a runtime flag ('needs_adjust_hs400')
is set when HS400 tuning was completed
- the callback will check the runtime flag and enable the corrected
manual mode if the flag is set and CMD13 is encountered
- at the end of the enablement the runtime flag is cleared
- iff the configuration flag is set, the manual mode will be disabled
when HS400 gets downgraded
There also some helper functions added to access the TMPPORT registers.
The actual correction table is SoC and instance(!) specific and is
added to the quirks struct.
Signed-off-by: Takeshi Saito <takeshi.saito.xv@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20200902081812.1591-3-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to have been added after kernel 5.4.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200903162412.6.Ib121debfb18e5f923a3cd38fe9c36aa086c650c5@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v5.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.5.I2b630c4d40ff4ea61d5b30b8ccfe95890e257100@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.19 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.4.I84eb3e0a738635d524c90d1a688087bc295f7c32@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.14 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SDHI drivers
Link: https://lore.kernel.org/r/20200903162412.3.Id1ff21470f08f427aedd0a6535dcd83ccc56b278@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.9 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200903162412.2.I226782b43191ce367fa3bc1c907c29f571890412@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This is like commit 3d3451124f3d ("mmc: sdhci-msm: Prefer asynchronous
probe") but applied to a whole pile of drivers. This batch converts
the drivers that appeared to be around in the v4.4 timeframe.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> # SH_MMCIF
Tested-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200903162412.1.Id501e96fa63224f77bb86b2135a5e8324ffb9c43@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Multiple MMC host controller driver can be compile tested as they do not
depend on architecture specific headers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200907105254.31097-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All entries in Kconfig are already part of "if MMC", so there is no need
for additional dependency on MMC.
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200904164315.24618-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since commit 9495b7e92f ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/85e1fc97dbec3dea96102785a5e308ccb5e91cfe.1599167798.git.robin.murphy@arm.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Because clk_disable_unprepare already checked NULL clock parameter, so the
additional checks are unnecessary, just remove them.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Link: https://lore.kernel.org/r/20200903084825.85616-1-vulab@iscas.ac.cn
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tuning procedure switches to lower frequencies but that will turn the
SCC off and accessing its register then will hang. So, check when we are
tuning and keep the current setup of the external clock if we are doing
so. Note that we still switch to the lower frequency because of the
internal divider. We just make sure to not modify the external clock.
This patch depends on a MMC core patch calling the downgrade function
earlier.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20200901150250.26236-4-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Turning on initcall debug on one system showed this:
initcall sdhci_msm_driver_init+0x0/0x28 returned 0 after 34782 usecs
The lion's share of this time (~33 ms) was in mmc_power_up(). This
shouldn't be terribly surprising since there are a few calls to delay
based on "power_delay_ms" and the default delay there is 10 ms.
Because we haven't specified that we'd prefer asynchronous probe for
this driver then we'll wait for this driver to finish before we start
probes for more drivers. While 33 ms doesn't sound like tons, every
little bit counts.
There should be little problem with turning on asynchronous probe for
this driver. It's already possible that previous drivers may have
turned on asynchronous probe so we might already have other things
(that probed before us) probing at the same time we are anyway. This
driver isn't really providing resources (clocks, regulators, etc) that
other drivers need to probe and even if it was they should be handling
-EPROBE_DEFER.
Let's turn this on and get a bit of boot speed back.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200902164303.1.I5e598a25222b4534c0083b61dbfa4e0e76f66171@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 'imask' and 'bsize' are not used in dbg_dumpregs:
drivers/mmc/host/s3cmci.c:149:36: warning: variable 'imask' set but not used [-Wunused-but-set-variable]
drivers/mmc/host/s3cmci.c:148:63: warning: variable 'bsize' set but not used [-Wunused-but-set-variable]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200903054333.18331-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since driver data is a pointer, direct casting to integer causes
warning when compile testing for 64-bit architecture:
drivers/mmc/host/s3cmci.c:1495:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
The actual driver data can be only 0 or 1, so cast it via long and do
not care about any loss of value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-3-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
iomem pointers should be printed with pointer format to hide the
actual value and fix warnings when compile testing for 64-bit
architecture:
drivers/mmc/host/s3cmci.c:1355:46: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-2-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Store in interrupt service routine always '1' in end_command, not the
value of host->cmd to fix compile test warnings on RISC-V:
drivers/mmc/host/davinci_mmc.c:999:17: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200902204847.2764-1-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Only -ENOENT from devm_clk_get() means that clock is not present in
device tree. Other errors have their own meaning and should not be
ignored.
Simplify getting the clock which is in fact optional and also use
dev_err_probe() for handling deferred.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20200902193658.20539-7-krzk@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
