The RXBD length field on all bnxt chips is 16-bit and so we cannot
support a full page when the native page size is 64K or greater.
The non-XDP (non page pool) code path has logic to handle this but
the XDP page pool code path does not handle this. Add the missing
logic to use page_pool_dev_alloc_frag() to allocate 32K chunks if
the page size is 64K or greater.
Fixes: 9f4b28301c ("bnxt: XDP multibuffer enablement")
Link: https://lore.kernel.org/netdev/20230728231829.235716-2-michael.chan@broadcom.com/
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230731142043.58855-2-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As documented in acd7aaf51b ("netsec: ignore 'phy-mode' device
property on ACPI systems") the SocioNext SynQuacer platform ships with
firmware defining the PHY mode as RGMII even though the physical
configuration of the PHY is for TX and RX delays. Since bbc4d71d63
("net: phy: realtek: fix rtl8211e rx/tx delay config") this has caused
misconfiguration of the PHY, rendering the network unusable.
This was worked around for ACPI by ignoring the phy-mode property but
the system is also used with DT. For DT instead if we're running on a
SynQuacer force a working PHY mode, as well as the standard EDK2
firmware with DT there are also some of these systems that use u-boot
and might not initialise the PHY if not netbooting. Newer firmware
imagaes for at least EDK2 are available from Linaro so print a warning
when doing this.
Fixes: 533dd11a12 ("net: socionext: Add Synquacer NetSec driver")
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230731-synquacer-net-v3-1-944be5f06428@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
in korina_probe(), the return value of clk_prepare_enable()
should be checked since it might fail. we can use
devm_clk_get_optional_enabled() instead of devm_clk_get_optional()
and clk_prepare_enable() to automatically handle the error.
Fixes: e4cd854ec4 ("net: korina: Get mdio input clock via common clock framework")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230731090535.21416-1-ruc_gongyuanjun@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most kernel functions return negative error codes but some irq functions
return zero on error. In this code irq_of_parse_and_map(), returns zero
and platform_get_irq() returns negative error codes. We need to handle
both cases appropriately.
Fixes: 8425c41d1e ("net: ll_temac: Extend support to non-device-tree platforms")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Esben Haabendal <esben@geanix.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Harini Katakam <harini.katakam@amd.com>
Link: https://lore.kernel.org/r/3d0aef75-06e0-45a5-a2a6-2cc4738d4143@moroto.mountain
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The two mbox-related mutexes are destroyed in octep_ctrl_mbox_uninit(),
but the corresponding mutex_init calls were missing.
A "DEBUG_LOCKS_WARN_ON(lock->magic != lock)" warning was emitted with
CONFIG_DEBUG_MUTEXES on.
Initialize the two mutexes in octep_ctrl_mbox_init().
Fixes: 577f0d1b1c ("octeon_ep: add separate mailbox command and response queues")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230729151516.24153-1-mschmidt@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Similarly to other recently fixed drivers make sure we don't
try to access XDP or page pool APIs when NAPI budget is 0.
NAPI budget of 0 may mean that we are in netpoll.
This may result in running software IRQs in hard IRQ context,
leading to deadlocks or crashes.
To make sure bnapi->tx_pkts don't get wiped without handling
the events, move clearing the field into the handler itself.
Remember to clear tx_pkts after reset (bnxt_enable_napi())
as it's technically possible that netpoll will accumulate
some tx_pkts and then a reset will happen, leaving tx_pkts
out of sync with reality.
Fixes: 322b87ca55 ("bnxt_en: add page_pool support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230728205020.2784844-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During qdisc create/delete, it is necessary to rebuild the queue
of VSIs. An error occurred because the VSIs created by RDMA were
still active.
Added check if RDMA is active. If yes, it disallows qdisc changes
and writes a message in the system logs.
Fixes: 348048e724 ("ice: Implement iidc operations")
Signed-off-by: Rafal Rogalski <rafalx.rogalski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Bharathi Sreenivas <bharathi.sreenivas@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230728171243.2446101-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a struct_group for the whole packet body so we can copy it in one
go without triggering FORTIFY_SOURCE complaints.
Fixes: cf60ed4696 ("sfc: use padding to fix alignment in loopback test")
Fixes: 30c24dd87f ("sfc: siena: use padding to fix alignment in loopback test")
Fixes: 1186c6b31e ("sfc: falcon: use padding to fix alignment in loopback test")
Reviewed-by: Andy Moreton <andy.moreton@amd.com>
Tested-by: Andy Moreton <andy.moreton@amd.com>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230728165528.59070-1-edward.cree@amd.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Here we've got to a situation when tasklet called usleep_range() in PTT
acquire logic, thus welcome to the "scheduling while atomic" BUG().
BUG: scheduling while atomic: swapper/24/0/0x00000100
[<ffffffffb41c6199>] schedule+0x29/0x70
[<ffffffffb41c5512>] schedule_hrtimeout_range_clock+0xb2/0x150
[<ffffffffb41c55c3>] schedule_hrtimeout_range+0x13/0x20
[<ffffffffb41c3bcf>] usleep_range+0x4f/0x70
[<ffffffffc08d3e58>] qed_ptt_acquire+0x38/0x100 [qed]
[<ffffffffc08eac48>] _qed_get_vport_stats+0x458/0x580 [qed]
[<ffffffffc08ead8c>] qed_get_vport_stats+0x1c/0xd0 [qed]
[<ffffffffc08dffd3>] qed_get_protocol_stats+0x93/0x100 [qed]
qed_mcp_send_protocol_stats
case MFW_DRV_MSG_GET_LAN_STATS:
case MFW_DRV_MSG_GET_FCOE_STATS:
case MFW_DRV_MSG_GET_ISCSI_STATS:
case MFW_DRV_MSG_GET_RDMA_STATS:
[<ffffffffc08e36d8>] qed_mcp_handle_events+0x2d8/0x890 [qed]
qed_int_assertion
qed_int_attentions
[<ffffffffc08d9490>] qed_int_sp_dpc+0xa50/0xdc0 [qed]
[<ffffffffb3aa7623>] tasklet_action+0x83/0x140
[<ffffffffb41d9125>] __do_softirq+0x125/0x2bb
[<ffffffffb41d560c>] call_softirq+0x1c/0x30
[<ffffffffb3a30645>] do_softirq+0x65/0xa0
[<ffffffffb3aa78d5>] irq_exit+0x105/0x110
[<ffffffffb41d8996>] do_IRQ+0x56/0xf0
Fix this by making caller to provide the context whether it could be in
atomic context flow or not when getting stats from QED driver.
QED driver based on the context provided decide to schedule out or not
when acquiring the PTT BAR window.
We faced the BUG_ON() while getting vport stats, but according to the
code same issue could happen for fcoe and iscsi statistics as well, so
fixing them too.
Fixes: 6c75424612 ("qed: Add support for NCSI statistics.")
Fixes: 1e128c8129 ("qed: Add support for hardware offloaded FCoE.")
Fixes: 2f2b2614e8 ("qed: Provide iSCSI statistics to management")
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: David Miller <davem@davemloft.net>
Cc: Manish Chopra <manishc@marvell.com>
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock data is an array of struct clk_bulk_data, so make sure to
allocate enough memory.
Fixes: d8ca113724 ("net: stmmac: tegra: Add MGBE support")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmTBkJkACgkQSD+KveBX
+j75KQf/Z2jvvcoH5aXCunGgF6+cbZGQ7KRIuxChgeHH1bYofNEAIiG4MmJEk7yi
8fs9ZJwAvQSZ3L7/VgeBrQ7l/qypIdg40QrA2b0vUUqLvObHbtM3sRcXGXkFmIL9
6gMiUsnhTeyBV4R3c7ViqPeEvPh0R7SLvvYd1QLemfJuWG9F7v8Tx87I0fVU9U3n
jqRpIcQjVg/o4ZlW0Jyh1BPqE9INPdmTTUiBt3fmfbLtbP8xRVcLpabeXyd2tDLl
yIXettLF97GwyzkMXu8zAx7mjRFZvbz7Tb2/g7sWNC7UlZmd4ho4jUHCTFuIUMwh
0+AVBW7RxhgL+VjXsGcPhSn8gnb1rw==
=MY4I
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2023-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-07-26
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-07-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Unregister devlink params in case interface is down
net/mlx5: DR, Fix peer domain namespace setting
net/mlx5: fs_chains: Fix ft prio if ignore_flow_level is not supported
net/mlx5e: kTLS, Fix protection domain in use syndrome when devlink reload
net/mlx5: Bridge, set debugfs access right to root-only
net/mlx5e: xsk: Fix crash on regular rq reactivation
net/mlx5e: xsk: Fix invalid buffer access for legacy rq
net/mlx5e: Move representor neigh cleanup to profile cleanup_tx
net/mlx5e: Fix crash moving to switchdev mode when ntuple offload is set
net/mlx5e: Don't hold encap tbl lock if there is no encap action
net/mlx5: Honor user input for migratable port fn attr
net/mlx5e: fix return value check in mlx5e_ipsec_remove_trailer()
net/mlx5: fix potential memory leak in mlx5e_init_rep_rx
net/mlx5: DR, fix memory leak in mlx5dr_cmd_create_reformat_ctx
net/mlx5e: fix double free in macsec_fs_tx_create_crypto_table_groups
====================
Link: https://lore.kernel.org/r/20230726213206.47022-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
in be_lancer_xmit_workarounds(), it should go to label 'tx_drop'
if an unexpected value is returned by pskb_trim().
Fixes: 93040ae5cc ("be2net: Fix to trim skb for padded vlan packets to workaround an ASIC Bug")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230725032726.15002-1-ruc_gongyuanjun@163.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to the clarification [1] in the latest napi.rst, the tx
processing cannot call any XDP (or page pool) APIs if the "budget"
is 0. Because NAPI is called with the budget of 0 (such as netpoll)
indicates we may be in an IRQ context, however, we cannot use the
page pool from IRQ context.
[1] https://lore.kernel.org/all/20230720161323.2025379-1-kuba@kernel.org/
Fixes: 20f7973990 ("net: fec: recycle pages for transmitted XDP frames")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20230725074148.2936402-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The offending patch is based on the assumption that for PFs,
mlx5_get_dev_index() is the same as vhca_id. However, this assumption
is wrong in case of DPU (ECPF).
Fix it by using vhca_id directly, and switch the array of peers to
xarray.
Fixes: 6d5b7321d8 ("net/mlx5: DR, handle more than one peer domain")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit sets ft prio to fs_base_prio. But if
ignore_flow_level it not supported, ft prio must be set based on
tc filter prio. Otherwise, all the ft prio are the same on the same
chain. It is invalid if ignore_flow_level is not supported.
Fix it by setting ft prio based on tc filter prio and setting
fs_base_prio to 0 for fdb.
Fixes: 8e80e56480 ("net/mlx5: fs_chains: Refactor to detach chains from tc usage")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There are DEK objects cached in DEK pool after kTLS is used, and they
are freed only in mlx5e_ktls_cleanup().
mlx5e_destroy_mdev_resources() is called in mlx5e_suspend() to
free mdev resources, including protection domain (PD). However, PD is
still referenced by the cached DEK objects in this case, because
profile->cleanup() (and therefore mlx5e_ktls_cleanup()) is called
after mlx5e_suspend() during devlink reload. So the following FW
syndrome is generated:
mlx5_cmd_out_err:803:(pid 12948): DEALLOC_PD(0x801) op_mod(0x0) failed,
status bad resource state(0x9), syndrome (0xef0c8a), err(-22)
To avoid this syndrome, move DEK pool destruction to
mlx5e_ktls_cleanup_tx(), which is called by profile->cleanup_tx(). And
move pool creation to mlx5e_ktls_init_tx() for symmetry.
Fixes: f741db1a51 ("net/mlx5e: kTLS, Improve connection rate by using fast update encryption key")
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
As suggested during code review set the access rights for bridge 'fdb'
debugfs file to root-only.
Fixes: 791eb78285 ("net/mlx5: Bridge, expose FDB state via debugfs")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/netdev/20230619120515.5045132a@kernel.org/
Signed-off-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When the regular rq is reactivated after the XSK socket is closed
it could be reading stale cqes which eventually corrupts the rq.
This leads to no more traffic being received on the regular rq and a
crash on the next close or deactivation of the rq.
Kal Cuttler Conely reported this issue as a crash on the release
path when the xdpsock sample program is stopped (killed) and restarted
in sequence while traffic is running.
This patch flushes all cqes when during the rq flush. The cqe flushing
is done in the reset state of the rq. mlx5e_rq_to_ready code is moved
into the flush function to allow for this.
Fixes: 082a9edf12 ("net/mlx5e: xsk: Flush RQ on XSK activation to save memory")
Reported-by: Kal Cutter Conley <kal.conley@dectris.com>
Closes: https://lore.kernel.org/xdp-newbies/CAHApi-nUAs4TeFWUDV915CZJo07XVg2Vp63-no7UDfj6wur9nQ@mail.gmail.com
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The cited commit holds encap tbl lock unconditionally when setting
up dests. But it may cause the following deadlock:
PID: 1063722 TASK: ffffa062ca5d0000 CPU: 13 COMMAND: "handler8"
#0 [ffffb14de05b7368] __schedule at ffffffffa1d5aa91
#1 [ffffb14de05b7410] schedule at ffffffffa1d5afdb
#2 [ffffb14de05b7430] schedule_preempt_disabled at ffffffffa1d5b528
#3 [ffffb14de05b7440] __mutex_lock at ffffffffa1d5d6cb
#4 [ffffb14de05b74e8] mutex_lock_nested at ffffffffa1d5ddeb
#5 [ffffb14de05b74f8] mlx5e_tc_tun_encap_dests_set at ffffffffc12f2096 [mlx5_core]
#6 [ffffb14de05b7568] post_process_attr at ffffffffc12d9fc5 [mlx5_core]
#7 [ffffb14de05b75a0] mlx5e_tc_add_fdb_flow at ffffffffc12de877 [mlx5_core]
#8 [ffffb14de05b75f0] __mlx5e_add_fdb_flow at ffffffffc12e0eef [mlx5_core]
#9 [ffffb14de05b7660] mlx5e_tc_add_flow at ffffffffc12e12f7 [mlx5_core]
#10 [ffffb14de05b76b8] mlx5e_configure_flower at ffffffffc12e1686 [mlx5_core]
#11 [ffffb14de05b7720] mlx5e_rep_indr_offload at ffffffffc12e3817 [mlx5_core]
#12 [ffffb14de05b7730] mlx5e_rep_indr_setup_tc_cb at ffffffffc12e388a [mlx5_core]
#13 [ffffb14de05b7740] tc_setup_cb_add at ffffffffa1ab2ba8
#14 [ffffb14de05b77a0] fl_hw_replace_filter at ffffffffc0bdec2f [cls_flower]
#15 [ffffb14de05b7868] fl_change at ffffffffc0be6caa [cls_flower]
#16 [ffffb14de05b7908] tc_new_tfilter at ffffffffa1ab71f0
[1031218.028143] wait_for_completion+0x24/0x30
[1031218.028589] mlx5e_update_route_decap_flows+0x9a/0x1e0 [mlx5_core]
[1031218.029256] mlx5e_tc_fib_event_work+0x1ad/0x300 [mlx5_core]
[1031218.029885] process_one_work+0x24e/0x510
Actually no need to hold encap tbl lock if there is no encap action.
Fix it by checking if encap action exists or not before holding
encap tbl lock.
Fixes: 37c3b9fa7c ("net/mlx5e: Prevent encap offload when neigh update is running")
Signed-off-by: Chris Mi <cmi@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, whenever a user is setting migratable port fn attr, the
driver is always turn migratable capability on.
Fix it by honor the user input
Fixes: e5b9642a33 ("net/mlx5: E-Switch, Implement devlink port function cmds to control migratable")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5e_ipsec_remove_trailer() should return an error code if function
pskb_trim() returns an unexpected value.
Fixes: 2ac9cfe782 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The memory pointed to by the priv->rx_res pointer is not freed in the error
path of mlx5e_init_rep_rx, which can lead to a memory leak. Fix by freeing
the memory in the error path, thereby making the error path identical to
mlx5e_cleanup_rep_rx().
Fixes: af8bbf7300 ("net/mlx5e: Convert mlx5e_flow_steering member of mlx5e_priv to pointer")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
when mlx5_cmd_exec failed in mlx5dr_cmd_create_reformat_ctx, the memory
pointed by 'in' is not released, which will cause memory leak. Move memory
release after mlx5_cmd_exec.
Fixes: 1d9186476e ("net/mlx5: DR, Add direct rule command utilities")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In function macsec_fs_tx_create_crypto_table_groups(), when the ft->g
memory is successfully allocated but the 'in' memory fails to be
allocated, the memory pointed to by ft->g is released once. And in function
macsec_fs_tx_create(), macsec_fs_tx_destroy() is called to release the
memory pointed to by ft->g again. This will cause double free problem.
Fixes: e467b283ff ("net/mlx5e: Add MACsec TX steering rules")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
commit a3a57bf07d ("net: stmmac: work
around sporadic tx issue on link-up") worked around a problem with TX
sometimes not working after a link-up by avoiding a redundant write to
MAC_CTRL_REG (aka GMAC_CONFIG), since the IP appeared to have problems
with handling multiple writes to that register in some cases.
That commit however only added the work around to dwmac_lib.c (apart
from the common code in stmmac_main.c), but my systems with version
4.21a of the IP exhibit the same problem, so add the work around to
dwmac4_lib.c too.
Fixes: a3a57bf07d ("net: stmmac: work around sporadic tx issue on link-up")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230721-stmmac-tx-workaround-v1-1-9411cbd5ee07@axis.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As of today, hash extraction support is enabled for all the silicons.
Because of which we are facing initialization issues when the silicon
does not support hash extraction. During creation of the hardware
parsing table for IPv6 address, we need to consider if hash extraction
is enabled then extract only 32 bit, otherwise 128 bit needs to be
extracted. This patch fixes the issue and configures the hardware parser
based on the availability of the feature.
Fixes: a95ab93550 ("octeontx2-af: Use hashed field in MCAM key")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230721061222.2632521-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-21 (i40e, iavf)
This series contains updates to i40e and iavf drivers.
Wang Ming corrects an error check on i40e.
Jake unlocks crit_lock on allocation failure to prevent deadlock and
stops re-enabling of interrupts when it's not intended for iavf.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: check for removal state before IAVF_FLAG_PF_COMMS_FAILED
iavf: fix potential deadlock on allocation failure
i40e: Fix an NULL vs IS_ERR() bug for debugfs_create_dir()
====================
Link: https://lore.kernel.org/r/20230721155812.1292752-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix ethtool FDIR logic to not use memory after its release.
In the ice_ethtool_fdir.c file there are 2 spots where code can
refer to pointers which may be missing.
In the ice_cfg_fdir_xtrct_seq() function seg may be freed but
even then may be still used by memcpy(&tun_seg[1], seg, sizeof(*seg)).
In the ice_add_fdir_ethtool() function struct ice_fdir_fltr *input
may first fail to be added via ice_fdir_update_list_entry() but then
may be deleted by ice_fdir_update_list_entry.
Terminate in both cases when the returned value of the previous
operation is other than 0, free memory and don't use it anymore.
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2208423
Fixes: cac2a27cd9 ("ice: Support IPv4 Flow Director filters")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230721155854.1292805-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the implementation of XDP of FEC driver, the XDP path
shares the transmit queues with the kernel network stack, so it is
possible to lead to a tx timeout event when XDP uses the tx queue
pretty much exclusively. And this event will cause the reset of the
FEC hardware.
To avoid timeout in this case, we use the txq_trans_cond_update()
interface to update txq->trans_start to jiffies so that watchdog
won't generate a transmit timeout warning.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Link: https://lore.kernel.org/r/20230721083559.2857312-1-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
in atl1e_tso_csum, it should check the return value of pskb_trim(),
and return an error code if an unexpected value is returned
by pskb_trim().
Fixes: a6a5325239 ("atl1e: Atheros L1E Gigabit Ethernet driver")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230720144219.39285-1-ruc_gongyuanjun@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
in atl1_tso(), it should check the return value of pskb_trim(),
and return an error code if an unexpected value is returned
by pskb_trim().
Fixes: 401c0aabec ("atl1: simplify tx packet descriptor")
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Link: https://lore.kernel.org/r/20230722142511.12448-1-ruc_gongyuanjun@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
in atl1c_tso_csum, it should check the return value of pskb_trim(),
and return an error code if an unexpected value is returned
by pskb_trim().
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN-GPE does not add an extra inner Ethernet header. Take that into
account when calculating header length.
This causes problems in skb_tunnel_check_pmtu, where incorrect PMTU is
cached.
In the collect_md mode (which is the only mode that VXLAN-GPE
supports), there's no magic auto-setting of the tunnel interface MTU.
It can't be, since the destination and thus the underlying interface
may be different for each packet.
So, the administrator is responsible for setting the correct tunnel
interface MTU. Apparently, the administrators are capable enough to
calculate that the maximum MTU for VXLAN-GPE is (their_lower_MTU - 36).
They set the tunnel interface MTU to 1464. If you run a TCP stream over
such interface, it's then segmented according to the MTU 1464, i.e.
producing 1514 bytes frames. Which is okay, this still fits the lower
MTU.
However, skb_tunnel_check_pmtu (called from vxlan_xmit_one) uses 50 as
the header size and thus incorrectly calculates the frame size to be
1528. This leads to ICMP too big message being generated (locally),
PMTU of 1450 to be cached and the TCP stream to be resegmented.
The fix is to use the correct actual header size, especially for
skb_tunnel_check_pmtu calculation.
Fixes: e1e5314de0 ("vxlan: implement GPE")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dwrr mode, the default bandwidth weight of disabled tc is set to 0.
If the bandwidth weight is 0, the mode will change to sp.
Therefore, disabled tc default bandwidth weight need changed to 1,
and 0 is returned when query the bandwidth weight of disabled tc.
In addition, driver need stop configure bandwidth weight if tc is disabled.
Fixes: 848440544b ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the weight saved by the driver is used as the query result,
which may be different from the actual weight in the register.
Therefore, the register value read from the firmware is used
as the query result
Fixes: 0e32038dc8 ("net: hns3: refactor dump tc of debugfs")
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tm module is configured with traffic, traffic
may be abnormal. This patch fixes this problem.
Before the tm module is configured, traffic processing
should be stopped. After the tm module is configured,
traffic processing is enabled.
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current only the first 32 bits of the capability flag bit are considered.
When the matching capability flag bit is greater than 31 bits,
it will get an error bit.This patch use bitmap to solve this issue.
It can handle each capability bit whitout bit width limit.
Fixes: da77aef9cc ("net: hns3: create common cmdq resource allocate/free/query APIs")
Signed-off-by: Hao Lan <lanhao@huawei.com>
Signed-off-by: Jijie Shao <shaojijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In iavf_adminq_task(), if the function can't acquire the
adapter->crit_lock, it checks if the driver is removing. If so, it simply
exits without re-enabling the interrupt. This is done to ensure that the
task stops processing as soon as possible once the driver is being removed.
However, if the IAVF_FLAG_PF_COMMS_FAILED is set, the function checks this
before attempting to acquire the lock. In this case, the function exits
early and re-enables the interrupt. This will happen even if the driver is
already removing.
Avoid this, by moving the check to after the adapter->crit_lock is
acquired. This way, if the driver is removing, we will not re-enable the
interrupt.
Fixes: fc2e6b3b13 ("iavf: Rework mutexes for better synchronisation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In iavf_adminq_task(), if kzalloc() fails to allocate the event.msg_buf,
the function will exit without releasing the adapter->crit_lock.
This is unlikely, but if it happens, the next access to that mutex will
deadlock.
Fix this by moving the unlock to the end of the function, and adding a new
label to allow jumping to the unlock portion of the function exit flow.
Fixes: fc2e6b3b13 ("iavf: Rework mutexes for better synchronisation")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The debugfs_create_dir() function returns error pointers.
It never returns NULL. Most incorrect error checks were fixed,
but the one in i40e_dbg_init() was forgotten.
Fix the remaining error check.
Fixes: 02e9c29081 ("i40e: debugfs interface")
Signed-off-by: Wang Ming <machel@vivo.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
entries and bind debugfs files would display wrong data on NETSYS_V2 and
later because instead of using mtk_get_ib1_pkt_type the driver would use
MTK_FOE_IB1_PACKET_TYPE which corresponds to NETSYS_V1(.x) SoCs.
Use mtk_get_ib1_pkt_type so entries and bind records display correctly.
Fixes: 03a3180e5c ("net: ethernet: mtk_eth_soc: introduce flow offloading support for mt7986")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c0ae03d0182f4d27b874cbdf0059bc972c317f3c.1689727134.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ocelot_fdma_receive_skb should return false if an unexpected
value is returned by pskb_trim.
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in emac_tso_csum(), return an error code if an unexpected value
is returned by pskb_trim().
Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-17 (iavf)
This series contains updates to iavf driver only.
Ding Hui fixes use-after-free issue by calling netif_napi_del() for all
allocated q_vectors. He also resolves out-of-bounds issue by not
updating to new values when timeout is encountered.
Marcin and Ahmed change the way resets are handled so that the callback
operating under the RTNL lock will wait for the reset to finish, the
rtnl_lock sensitive functions in reset flow will schedule the netdev update
for later in order to remove circular dependency with the critical lock.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: fix reset task race with iavf_remove()
iavf: fix a deadlock caused by rtnl and driver's lock circular dependencies
Revert "iavf: Do not restart Tx queues after reset task failure"
Revert "iavf: Detach device during reset task"
iavf: Wait for reset in callbacks which trigger it
iavf: use internal state to free traffic IRQs
iavf: Fix out-of-bounds when setting channels on remove
iavf: Fix use-after-free in free_netdev
====================
Link: https://lore.kernel.org/r/20230717175205.3217774-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Hardware generated encryption and ICV tags are found to
be wrong when tested with IEEE MACSEC test vectors.
This is because as per the HRM, the hash key (derived by
AES-ECB block encryption of an all 0s block with the SAK)
has to be programmed by the software in
MCSX_RS_MCS_CPM_TX_SLAVE_SA_PLCY_MEM_4X register.
Hence fix this by generating hash key in software and
configuring in hardware.
Fixes: c54ffc7360 ("octeontx2-pf: mcs: Introduce MACSEC hardware offloading")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Link: https://lore.kernel.org/r/1689574603-28093-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In normal operation, each populated queue item has
next_to_watch pointing to the last TX desc of the packet,
while each cleaned item has it set to 0. In particular,
next_to_use that points to the next (necessarily clean)
item to use has next_to_watch set to 0.
When the TX queue is used both by an application using
AF_XDP with ZEROCOPY as well as a second non-XDP application
generating high traffic, the queue pointers can get in
an invalid state where next_to_use points to an item
where next_to_watch is NOT set to 0.
However, the implementation assumes at several places
that this is never the case, so if it does hold,
bad things happen. In particular, within the loop inside
of igc_clean_tx_irq(), next_to_clean can overtake next_to_use.
Finally, this prevents any further transmission via
this queue and it never gets unblocked or signaled.
Secondly, if the queue is in this garbled state,
the inner loop of igc_clean_tx_ring() will never terminate,
completely hogging a CPU core.
The reason is that igc_xdp_xmit_zc() reads next_to_use
before acquiring the lock, and writing it back
(potentially unmodified) later. If it got modified
before locking, the outdated next_to_use is written
pointing to an item that was already used elsewhere
(and thus next_to_watch got written).
Fixes: 9acf59a752 ("igc: Enable TX via AF_XDP zero-copy")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230717175444.3217831-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current driver enables backpressure for LBK interfaces.
But these interfaces do not support this feature.
Hence, this patch fixes the issue by skipping the
backpressure configuration for these interfaces.
Fixes: 75f3627099 ("octeontx2-pf: Support to enable/disable pause frames via ethtool").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Link: https://lore.kernel.org/r/20230716093741.28063-1-gakula@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-14 (ice)
This series contains updates to ice driver only.
Petr Oros removes multiple calls made to unregister netdev and
devlink_port.
Michal fixes null pointer dereference that can occur during reload.
====================
Link: https://lore.kernel.org/r/20230714201041.1717834-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The reset task is currently scheduled from the watchdog or adminq tasks.
First, all direct calls to schedule the reset task are replaced with the
iavf_schedule_reset(), which is modified to accept the flag showing the
type of reset.
To prevent the reset task from starting once iavf_remove() starts, we need
to check the __IAVF_IN_REMOVE_TASK bit before we schedule it. This is now
easily added to iavf_schedule_reset().
Finally, remove the check for IAVF_FLAG_RESET_NEEDED in the watchdog task.
It is redundant since all callers who set the flag immediately schedules
the reset task.
Fixes: 3ccd54ef44 ("iavf: Fix init state closure on remove")
Fixes: 14756b2ae2 ("iavf: Fix __IAVF_RESETTING state usage")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
A driver's lock (crit_lock) is used to serialize all the driver's tasks.
Lockdep, however, shows a circular dependency between rtnl and
crit_lock. This happens when an ndo that already holds the rtnl requests
the driver to reset, since the reset task (in some paths) tries to grab
rtnl to either change real number of queues of update netdev features.
[566.241851] ======================================================
[566.241893] WARNING: possible circular locking dependency detected
[566.241936] 6.2.14-100.fc36.x86_64+debug #1 Tainted: G OE
[566.241984] ------------------------------------------------------
[566.242025] repro.sh/2604 is trying to acquire lock:
[566.242061] ffff9280fc5ceee8 (&adapter->crit_lock){+.+.}-{3:3}, at: iavf_close+0x3c/0x240 [iavf]
[566.242167]
but task is already holding lock:
[566.242209] ffffffff9976d350 (rtnl_mutex){+.+.}-{3:3}, at: iavf_remove+0x6b5/0x730 [iavf]
[566.242300]
which lock already depends on the new lock.
[566.242353]
the existing dependency chain (in reverse order) is:
[566.242401]
-> #1 (rtnl_mutex){+.+.}-{3:3}:
[566.242451] __mutex_lock+0xc1/0xbb0
[566.242489] iavf_init_interrupt_scheme+0x179/0x440 [iavf]
[566.242560] iavf_watchdog_task+0x80b/0x1400 [iavf]
[566.242627] process_one_work+0x2b3/0x560
[566.242663] worker_thread+0x4f/0x3a0
[566.242696] kthread+0xf2/0x120
[566.242730] ret_from_fork+0x29/0x50
[566.242763]
-> #0 (&adapter->crit_lock){+.+.}-{3:3}:
[566.242815] __lock_acquire+0x15ff/0x22b0
[566.242869] lock_acquire+0xd2/0x2c0
[566.242901] __mutex_lock+0xc1/0xbb0
[566.242934] iavf_close+0x3c/0x240 [iavf]
[566.242997] __dev_close_many+0xac/0x120
[566.243036] dev_close_many+0x8b/0x140
[566.243071] unregister_netdevice_many_notify+0x165/0x7c0
[566.243116] unregister_netdevice_queue+0xd3/0x110
[566.243157] iavf_remove+0x6c1/0x730 [iavf]
[566.243217] pci_device_remove+0x33/0xa0
[566.243257] device_release_driver_internal+0x1bc/0x240
[566.243299] pci_stop_bus_device+0x6c/0x90
[566.243338] pci_stop_and_remove_bus_device+0xe/0x20
[566.243380] pci_iov_remove_virtfn+0xd1/0x130
[566.243417] sriov_disable+0x34/0xe0
[566.243448] ice_free_vfs+0x2da/0x330 [ice]
[566.244383] ice_sriov_configure+0x88/0xad0 [ice]
[566.245353] sriov_numvfs_store+0xde/0x1d0
[566.246156] kernfs_fop_write_iter+0x15e/0x210
[566.246921] vfs_write+0x288/0x530
[566.247671] ksys_write+0x74/0xf0
[566.248408] do_syscall_64+0x58/0x80
[566.249145] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[566.249886]
other info that might help us debug this:
[566.252014] Possible unsafe locking scenario:
[566.253432] CPU0 CPU1
[566.254118] ---- ----
[566.254800] lock(rtnl_mutex);
[566.255514] lock(&adapter->crit_lock);
[566.256233] lock(rtnl_mutex);
[566.256897] lock(&adapter->crit_lock);
[566.257388]
*** DEADLOCK ***
The deadlock can be triggered by a script that is continuously resetting
the VF adapter while doing other operations requiring RTNL, e.g:
while :; do
ip link set $VF up
ethtool --set-channels $VF combined 2
ip link set $VF down
ip link set $VF up
ethtool --set-channels $VF combined 4
ip link set $VF down
done
Any operation that triggers a reset can substitute "ethtool --set-channles"
As a fix, add a new task "finish_config" that do all the work which
needs rtnl lock. With the exception of iavf_remove(), all work that
require rtnl should be called from this task.
As for iavf_remove(), at the point where we need to call
unregister_netdevice() (and grab rtnl_lock), we make sure the finish_config
task is not running (cancel_work_sync()) to safely grab rtnl. Subsequent
finish_config work cannot restart after that since the task is guarded
by the __IAVF_IN_REMOVE_TASK bit in iavf_schedule_finish_config().
Fixes: 5ac49f3c27 ("iavf: use mutexes for locking of critical sections")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit 08f1c147b7.
Netdev is no longer being detached during reset, so this fix can be
reverted. We leave the removal of "hacky" IFF_UP flag update.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This reverts commit aa626da947.
Detaching device during reset was not fully fixing the rtnl locking issue,
as there could be a situation where callback was already in progress before
detaching netdev.
Furthermore, detaching netdevice causes TX timeouts if traffic is running.
To reproduce:
ip netns exec ns1 iperf3 -c $PEER_IP -t 600 --logfile /dev/null &
while :; do
for i in 200 7000 400 5000 300 3000 ; do
ip netns exec ns1 ip link set $VF1 mtu $i
sleep 2
done
sleep 10
done
Currently, callbacks such as iavf_change_mtu() wait for the reset.
If the reset fails to acquire the rtnl_lock, they schedule the netdev
update for later while continuing the reset flow. Operations like MTU
changes are performed under the rtnl_lock. Therefore, when the operation
finishes, another callback that uses rtnl_lock can start.
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was a fail when trying to add the interface to bonding
right after changing the MTU on the interface. It was caused
by bonding interface unable to open the interface due to
interface being in __RESETTING state because of MTU change.
Add new reset_waitqueue to indicate that reset has finished.
Add waiting for reset to finish in callbacks which trigger hw reset:
iavf_set_priv_flags(), iavf_change_mtu() and iavf_set_ringparam().
We use a 5000ms timeout period because on Hyper-V based systems,
this operation takes around 3000-4000ms. In normal circumstances,
it doesn't take more than 500ms to complete.
Add a function iavf_wait_for_reset() to reuse waiting for reset code and
use it also in iavf_set_channels(), which already waits for reset.
We don't use error handling in iavf_set_channels() as this could
cause the device to be in incorrect state if the reset was scheduled
but hit timeout or the waitng function was interrupted by a signal.
Fixes: 4e5e6b5d9d ("iavf: Fix return of set the new channel count")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Co-developed-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
If the system tries to close the netdev while iavf_reset_task() is
running, __LINK_STATE_START will be cleared and netif_running() will
return false in iavf_reinit_interrupt_scheme(). This will result in
iavf_free_traffic_irqs() not being called and a leak as follows:
[7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0'
[7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0
is shown when pci_disable_msix() is later called. Fix by using the
internal adapter state. The traffic IRQs will always exist if
state == __IAVF_RUNNING.
Fixes: 5b36e8d04b ("i40evf: Enable VF to request an alternate queue allocation")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Referenced commit missed that for chip versions 42 and 43 ASPM
remained disabled in the respective rtl_hw_start_...() routines.
This resulted in problems as described in the referenced bug
ticket. Therefore re-instantiate the previous logic.
Fixes: 5fc3f6c90c ("r8169: consolidate disabling ASPM before EPHY access")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217635
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 6624e780a5 ("ice: split ice_vsi_setup into smaller
functions") ice_vsi_release does things twice. There is unregister
netdev which is unregistered in ice_deinit_eth also.
It also unregisters the devlink_port twice which is also unregistered
in ice_deinit_eth(). This double deregistration is hidden because
devl_port_unregister ignores the return value of xa_erase.
[ 68.642167] Call Trace:
[ 68.650385] ice_devlink_destroy_pf_port+0xe/0x20 [ice]
[ 68.655656] ice_vsi_release+0x445/0x690 [ice]
[ 68.660147] ice_deinit+0x99/0x280 [ice]
[ 68.664117] ice_remove+0x1b6/0x5c0 [ice]
[ 171.103841] Call Trace:
[ 171.109607] ice_devlink_destroy_pf_port+0xf/0x20 [ice]
[ 171.114841] ice_remove+0x158/0x270 [ice]
[ 171.118854] pci_device_remove+0x3b/0xc0
[ 171.122779] device_release_driver_internal+0xc7/0x170
[ 171.127912] driver_detach+0x54/0x8c
[ 171.131491] bus_remove_driver+0x77/0xd1
[ 171.135406] pci_unregister_driver+0x2d/0xb0
[ 171.139670] ice_module_exit+0xc/0x55f [ice]
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Identify issues that arise by using the tests/doublebitand.cocci
semantic patch. Need to remove duplicate expression in if statement.
Signed-off-by: Wang Ming <machel@vivo.com>
Reviewed-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is expected that most callers should _ignore_ the errors return by
debugfs_create_dir() in bnad_debugfs_init().
Signed-off-by: Wang Ming <machel@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call to of_get_ethdev_address to mtk_add_mac which is part of
the probe function and can hence itself return -EPROBE_DEFER should
of_get_ethdev_address return -EPROBE_DEFER. This allows us to entirely
get rid of the mtk_init function.
The problem of of_get_ethdev_address returning -EPROBE_DEFER surfaced
in situations in which the NVMEM provider holding the MAC address has
not yet be loaded at the time mtk_eth_soc is initially probed. In this
case probing of mtk_eth_soc should be deferred instead of falling back
to use a random MAC address, so once the NVMEM provider becomes
available probing can be repeated.
Fixes: 656e705243 ("net-next: mediatek: add support for MT7623 ethernet")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW ALE has 75 bit ALE entries which are stored within three 32 bit words.
The cpsw_ale_get_field() and cpsw_ale_set_field() functions assume that the
field will be strictly contained within one word. However, this is not
guaranteed to be the case and it is possible for ALE field entries to span
across up to two words at the most.
Fix the methods to handle getting/setting fields spanning up to two words.
Fixes: db82173f23 ("netdev: driver: ethernet: add cpsw address lookup engine support")
Signed-off-by: Tanmay Patil <t-patil@ti.com>
[s-vadapalli@ti.com: rephrased commit message and added Fixes tag]
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some device types like TXGBE_ID_XAUI, *checksum computed in
txgbe_calc_eeprom_checksum() is larger than TXGBE_EEPROM_SUM. Remove the
limit on the size of *checksum.
Fixes: 049fe53653 ("net: txgbe: Add operations to interact with firmware")
Fixes: 5e2ea7801f ("net: txgbe: Fix unsigned comparison to zero in txgbe_calc_eeprom_checksum()")
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Link: https://lore.kernel.org/r/20230711063414.3311-1-jiawenwu@trustnetic.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ENA adapters on our instances occasionally reset. Once recently
logged a UBSAN failure to console in the process:
UBSAN: shift-out-of-bounds in build/linux/drivers/net/ethernet/amazon/ena/ena_com.c:540:13
shift exponent 32 is too large for 32-bit type 'unsigned int'
CPU: 28 PID: 70012 Comm: kworker/u72:2 Kdump: loaded not tainted 5.15.117
Hardware name: Amazon EC2 c5d.9xlarge/, BIOS 1.0 10/16/2017
Workqueue: ena ena_fw_reset_device [ena]
Call Trace:
<TASK>
dump_stack_lvl+0x4a/0x63
dump_stack+0x10/0x16
ubsan_epilogue+0x9/0x36
__ubsan_handle_shift_out_of_bounds.cold+0x61/0x10e
? __const_udelay+0x43/0x50
ena_delay_exponential_backoff_us.cold+0x16/0x1e [ena]
wait_for_reset_state+0x54/0xa0 [ena]
ena_com_dev_reset+0xc8/0x110 [ena]
ena_down+0x3fe/0x480 [ena]
ena_destroy_device+0xeb/0xf0 [ena]
ena_fw_reset_device+0x30/0x50 [ena]
process_one_work+0x22b/0x3d0
worker_thread+0x4d/0x3f0
? process_one_work+0x3d0/0x3d0
kthread+0x12a/0x150
? set_kthread_struct+0x50/0x50
ret_from_fork+0x22/0x30
</TASK>
Apparently, the reset delays are getting so large they can trigger a
UBSAN panic.
Looking at the code, the current timeout is capped at 5000us. Using a
base value of 100us, the current code will overflow after (1<<29). Even
at values before 32, this function wraps around, perhaps
unintentionally.
Cap the value of the exponent used for this backoff at (1<<16) which is
larger than currently necessary, but large enough to support bigger
values in the future.
Cc: stable@vger.kernel.org
Fixes: 4bb7f4cf60 ("net: ena: reduce driver load time")
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/r/20230711013621.GE1926@templeofstupid.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
igc: Fix corner cases for TSN offload
Florian Kauer says:
The igc driver supports several different offloading capabilities
relevant in the TSN context. Recent patches in this area introduced
regressions for certain corner cases that are fixed in this series.
Each of the patches (except the first one) addresses a different
regression that can be separately reproduced. Still, they have
overlapping code changes so they should not be separately applied.
Especially #4 and #6 address the same observation,
but both need to be applied to avoid TX hang occurrences in
the scenario described in the patches.
====================
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to hardware limitation, MCAM drop rule with
ether_type == 802.1Q and vlan_id == 0 is not supported. Hence rejecting
such rules.
Fixes: dce677da57 ("octeontx2-pf: Add vlan-etype to ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Link: https://lore.kernel.org/r/20230710103027.2244139-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In the case of heavy XDP traffic to be transmitted, the console
will print the error log continuously if there are lack of enough
BDs to accommodate the frames. The log looks like below.
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
Not only will this log be replicated and redundant, it will also
degrade XDP performance. So we use netdev_err_once() instead of
netdev_err() now.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the XDP feature is enabled and with heavy XDP frames to be
transmitted, there is a considerable probability that available
tx BDs are insufficient. This will lead to some XDP frames to be
discarded and the "NOT enough BD for SG!" error log will appear
in the console (as shown below).
[ 160.013112] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.023116] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.028926] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.038946] fec 30be0000.ethernet eth0: NOT enough BD for SG!
[ 160.044758] fec 30be0000.ethernet eth0: NOT enough BD for SG!
In the case of heavy XDP traffic, sometimes the speed of recycling
tx BDs may be slower than the speed of sending XDP frames. There
may be several specific reasons, such as the interrupt is not
responsed in time, the efficiency of the NAPI callback function is
too low due to all the queues (tx queues and rx queues) share the
same NAPI, and so on.
After trying various methods, I think that increase the size of tx
BD ring is simple and effective. Maybe the best resolution is that
allocate NAPI for each queue to improve the efficiency of the NAPI
callback, but this change is a bit big and I didn't try this method.
Perheps this method will be implemented in a future patch.
This patch also updates the tx_wake_threshold of tx ring which is
related to the size of tx ring in the previous logic. Otherwise,
the tx_wake_threshold will be too high (403 BDs), which is more
likely to impact the slow path in the case of heavy XDP traffic,
because XDP path and slow path share the tx BD rings. According
to Jakub's suggestion, the tx_wake_threshold is at least equal to
tx_stop_threshold + 2 * MAX_SKB_FRAGS, if a queue of hundreds of
entries is overflowing, we should be able to apply a hysteresis
of a few tens of entries.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Once the XDP frames have been successfully transmitted through the
ndo_xdp_xmit() interface, it's the driver responsibility to free
the frames so that the page_pool can recycle the pages and reuse
them. However, this action is not implemented in the fec driver.
This leads to a user-visible problem that the console will print
the following warning log.
[ 157.568851] page_pool_release_retry() stalled pool shutdown 1389 inflight 60 sec
[ 217.983446] page_pool_release_retry() stalled pool shutdown 1389 inflight 120 sec
[ 278.399006] page_pool_release_retry() stalled pool shutdown 1389 inflight 181 sec
[ 338.812885] page_pool_release_retry() stalled pool shutdown 1389 inflight 241 sec
[ 399.226946] page_pool_release_retry() stalled pool shutdown 1389 inflight 302 sec
Therefore, to solve this issue, we free XDP frames via xdp_return_frame()
while cleaning the tx BD ring.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When a XDP program is installed or uninstalled, fec_restart() will
be invoked to reset MAC and buffer descriptor rings. It's reasonable
not to transmit any packet during the process of reset. However, the
NETDEV_XDP_ACT_NDO_XMIT bit of xdp_features is enabled by default,
that is to say, it's possible that the fec_enet_xdp_xmit() will be
invoked even if the process of reset is not finished. In this case,
the redirected XDP frames might be dropped and available transmit BDs
may be incorrectly deemed insufficient. So this patch disable the
NETDEV_XDP_ACT_NDO_XMIT feature by default and dynamically configure
this feature when the bpf program is installed or uninstalled.
Fixes: e4ac7cc6e5 ("net: fec: turn on XDP features")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The insertion of an empty frame was introduced with
commit db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
in order to ensure that the current cycle has at least one packet if
there is some packet to be scheduled for the next cycle.
However, the current implementation does not properly check if
a packet is already scheduled for the current cycle. Currently,
an empty packet is always inserted if and only if
txtime >= end_of_cycle && txtime > last_tx_cycle
but since last_tx_cycle is always either the end of the current
cycle (end_of_cycle) or the end of a previous cycle, the
second part (txtime > last_tx_cycle) is always true unless
txtime == last_tx_cycle.
What actually needs to be checked here is if the last_tx_cycle
was already written within the current cycle, so an empty frame
should only be inserted if and only if
txtime >= end_of_cycle && end_of_cycle > last_tx_cycle.
This patch does not only avoid an unnecessary insertion, but it
can actually be harmful to insert an empty packet if packets
are already scheduled in the current cycle, because it can lead
to a situation where the empty packet is actually processed
as the first packet in the upcoming cycle shifting the packet
with the first_flag even one cycle into the future, finally leading
to a TX hang.
The TX hang can be reproduced on a i225 with:
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <32>
TDT <3c>
next_to_use <3c>
next_to_clean <32>
buffer_info[next_to_clean]
time_stamp <ffff26a8>
next_to_watch <00000000632a1828>
jiffies <ffff27f8>
desc.status <1048000>
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
It is possible (verified on a running system) that frames are processed
by igc_tx_launchtime with a txtime before the start of the cycle
(baset_est).
However, the result of txtime - baset_est is written into a u32,
leading to a wrap around to a positive number. The following
launchtime > 0 check will only branch to executing launchtime = 0
if launchtime is already 0.
Fix it by using a s32 before checking launchtime > 0.
Fixes: db0b124f02 ("igc: Enhance Qbv scheduling by using first flag bit")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The flags IGC_TXQCTL_STRICT_CYCLE and IGC_TXQCTL_STRICT_END
prevent the packet transmission over slot and cycle boundaries.
This is important for taprio offload where the slots and
cycles correspond to the slots and cycles configured for the
network.
However, the Qbv offload feature of the i225 is also used for
enabling TX launchtime / ETF offload. In that case, however,
the cycle has no meaning for the network and is only used
internally to adapt the base time register after a second has
passed.
Enabling strict mode in this case would unnecessarily prevent
the transmission of certain packets (i.e. at the boundary of a
second) and thus interferes with the ETF qdisc that promises
transmission at a certain point in time.
Similar to ETF, this also applies to CBS offload that also should
not be influenced by strict mode unless taprio offload would be
enabled at the same time.
This fully reverts
commit d8f45be01d ("igc: Use strict cycles for Qbv scheduling")
but its commit message only describes what was already implemented
before that commit. The difference to a plain revert of that commit
is that it now copes with the base_time = 0 case that was fixed with
commit e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
In particular, enabling strict mode leads to TX hang situations
under high traffic if taprio is applied WITHOUT taprio offload
but WITH ETF offload, e.g. as in
sudo tc qdisc replace dev enp1s0 parent root handle 100 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x1 \
txtime-delay 500000 \
clockid CLOCK_TAI
sudo tc qdisc replace dev enp1s0 parent 100:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload \
skip_sock_check
and traffic generator
sudo trafgen -i traffic.cfg -o enp1s0 --cpp -n0 -q -t1400ns
with traffic.cfg
#define ETH_P_IP 0x0800
{
/* Ethernet Header */
0x30, 0x1f, 0x9a, 0xd0, 0xf0, 0x0e, # MAC Dest - adapt as needed
0x24, 0x5e, 0xbe, 0x57, 0x2e, 0x36, # MAC Src - adapt as needed
const16(ETH_P_IP),
/* IPv4 Header */
0b01000101, 0, # IPv4 version, IHL, TOS
const16(1028), # IPv4 total length (UDP length + 20 bytes (IP header))
const16(2), # IPv4 ident
0b01000000, 0, # IPv4 flags, fragmentation off
64, # IPv4 TTL
17, # Protocol UDP
csumip(14, 33), # IPv4 checksum
/* UDP Header */
10, 0, 48, 1, # IP Src - adapt as needed
10, 0, 48, 10, # IP Dest - adapt as needed
const16(5555), # UDP Src Port
const16(6666), # UDP Dest Port
const16(1008), # UDP length (UDP header 8 bytes + payload length)
csumudp(14, 34), # UDP checksum
/* Payload */
fill('W', 1000),
}
and the observed message with that is for example
igc 0000:01:00.0 enp1s0: Detected Tx Unit Hang
Tx Queue <0>
TDH <d0>
TDT <f0>
next_to_use <f0>
next_to_clean <d0>
buffer_info[next_to_clean]
time_stamp <ffff661f>
next_to_watch <00000000245a4efb>
jiffies <ffff6e48>
desc.status <1048000>
Fixes: d8f45be01d ("igc: Use strict cycles for Qbv scheduling")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Since commit e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
it is possible to enable taprio offload with a basetime of 0.
However, the check if taprio offload is already enabled (and thus -EALREADY
should be returned for igc_save_qbv_schedule) still relied on
adapter->base_time > 0.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and base-time = 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
# The second call should fail with "Error: Device failed to setup taprio offload."
# But that only happens if base-time was != 0
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time 0 \
sched-entry S 01 300000 \
flags 0x2
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Only set adapter->taprio_offload_enable after validating the arguments.
Otherwise, it stays set even if the offload was not enabled.
Since the subsequent code does not get executed in case of invalid
arguments, it will not be read at first.
However, by activating and then deactivating another offload
(e.g. ETF/TX launchtime offload), taprio_offload_enable is read
and erroneously keeps the offload feature of the NIC enabled.
This can be reproduced as follows:
# TAPRIO offload (flags == 0x2) and negative base-time leading to expected -ERANGE
sudo tc qdisc replace dev enp1s0 parent root handle 100 stab overhead 24 taprio \
num_tc 1 \
map 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 \
queues 1@0 \
base-time -1000 \
sched-entry S 01 300000 \
flags 0x2
# IGC_TQAVCTRL is 0x0 as expected (iomem=relaxed for reading register)
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Activate ETF offload
sudo tc qdisc replace dev enp1s0 parent root handle 6666 mqprio \
num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 \
queues 1@0 1@1 2@2 \
hw 0
sudo tc qdisc add dev enp1s0 parent 6666:1 etf \
clockid CLOCK_TAI \
delta 500000 \
offload
# IGC_TQAVCTRL is 0x9 as expected
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
# Deactivate ETF offload again
sudo tc qdisc delete dev enp1s0 parent 6666:1
# IGC_TQAVCTRL should now be 0x0 again, but is observed as 0x9
sudo pcimem /sys/bus/pci/devices/0000:01:00.0/resource0 0x3570 w*1
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In the current implementation the flags adapter->qbv_enable
and IGC_FLAG_TSN_QBV_ENABLED have a similar name, but do not
have the same meaning. The first one is used only to indicate
taprio offload (i.e. when igc_save_qbv_schedule was called),
while the second one corresponds to the Qbv mode of the hardware.
However, the second one is also used to support the TX launchtime
feature, i.e. ETF qdisc offload. This leads to situations where
adapter->qbv_enable is false, but the flag IGC_FLAG_TSN_QBV_ENABLED
is set. This is prone to confusion.
The rename should reduce this confusion. Since it is a pure
rename, it has no impact on functionality.
Fixes: e17090eb24 ("igc: allow BaseTime 0 enrollment for Qbv")
Signed-off-by: Florian Kauer <florian.kauer@linutronix.de>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Current codebase contained the usage of two different names for this
driver (i.e., `gvnic` and `gve`), which is quite unfriendly for users
to use, especially when trying to bind or unbind the driver manually.
The corresponding kernel module is registered with the name of `gve`.
It's more reasonable to align the name of the driver with the module.
Fixes: 893ce44df5 ("gve: Add basic driver framework for Compute Engine Virtual NIC")
Cc: csully@google.com
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit introduces usage of fixed_phy_register() but
not a corresponding dependency on FIXED_PHY.
This can result in a build failure.
s390-linux-ld: drivers/net/ethernet/microchip/lan743x_main.o: in function `lan743x_phy_open':
drivers/net/ethernet/microchip/lan743x_main.c:1514: undefined reference to `fixed_phy_register'
Fixes: 624864fbff ("net: lan743x: add fixed phy support for LAN7431 device")
Cc: stable@vger.kernel.org
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/netdev/725bf1c5-b252-7d19-7582-a6809716c7d6@infradead.org/
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turning IRQs off is done by accessing Ethernet controller registers.
That can't be done until device's clock is enabled. It results in a SoC
hang otherwise.
This bug remained unnoticed for years as most bootloaders keep all
Ethernet interfaces turned on. It seems to only affect a niche SoC
family BCM47189. It has two Ethernet controllers but CFE bootloader uses
only the first one.
Fixes: 34322615cb ("net: bgmac: Mask interrupts during probe")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the probe error path code that leaves the driver bound
to the device, but with essentially a dead device. This was
useful maybe twice early in the driver's life and no longer
makes sense to keep.
Fixes: 30a1e6d0f8 ("ionic: keep ionic dev on lif init fail")
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary early code development check and the WARN_ON
that it uses. The irq alloc and free paths have long been
cleaned up and this check shouldn't have stuck around so long.
Fixes: 77ceb68e29 ("ionic: Add notifyq support")
Signed-off-by: Nitya Sunkad <nitya.sunkad@amd.com>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved PTP pointer validation before its use to avoid smatch warning.
Also used kzalloc/kfree instead of devm_kzalloc/devm_kfree.
Fixes: 2ef4e45d99 ("octeontx2-af: Add PTP PPS Errata workaround on CN10K silicon")
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In legacy silicon, promiscuous mode is only modified
through CGX mbox messages. In CN10KB silicon, it is modified
from CGX mbox and NIX. This breaks legacy application
behaviour. Fix this by removing call from NIX.
Fixes: d6c9784baf ("octeontx2-af: Invoke exact match functions if supported")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-05 (igc)
This series contains updates to igc driver only.
Husaini adds check to increment Qbv change error counter only on taprio
Qbvs. He also removes delay during Tx ring configuration and
resolves Tx hang that could occur when transmitting on a gate to be
closed.
Prasad Koya reports ethtool link mode as TP (twisted pair).
Tee Min corrects value for max SDU.
Aravindhan ensures that registers for PPS are always programmed to occur
in future.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Current duplex mode was unset in the driver, resulting in the default
parameter being set to 0, which corresponds to half duplex. It might
mislead users to have incorrect expectation about the driver's
transmission capabilities.
Set the default duplex configuration to full, as the driver runs in
full duplex mode at this point.
Fixes: 7e074d5a76 ("gve: Enable Link Speed Reporting in the driver.")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Message-ID: <20230706044128.2726747-1-junfeng.guo@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-07-05 (ice)
This series contains updates to ice driver only.
Sridhar fixes incorrect comparison of max Tx rate limit to occur against
each TC value rather than the aggregate. He also resolves an issue with
the wrong VSI being used when setting max Tx rate when TCs are enabled.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix tx queue rate limit when TCs are configured
ice: Fix max_rate check while configuring TX rate limits
====================
Link: https://lore.kernel.org/r/20230705201346.49370-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmSlrvAACgkQSD+KveBX
+j4EcggAsZlHQHRaA9re/5Fr8VV/YNmf+eLM6/2F6CD1sLcwWEsmDXkqZpL/wqVv
bcP/dE/ehiMd1FI6XmEb9aGZY29mQBoItwCnxeUrK75d8CQib/pH87VkQdT9Uf6W
RVqPk2rOL778sTy6V/UZDecfmZB5XfEoOO6f0YP/j2t8HxmfdetBN0orE0iRQBmO
+0W8X5bIfCmGyWdQzOJB4a+S7Wi1JACr6CIOdNtADuZ7C7kKiPWrvEl7DMHlyX3Y
TyrE//piSJuxaHwdMNBHPsXK5ZYyn7ZJjqeCA+Kd+lKMJlJEO7R+TkTOP0RKE++a
ZdDetCqLKegQPpWZgjGzei7PpSpaFA==
=cNgk
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2023-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2023-07-05
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2023-07-05' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: RX, Fix page_pool page fragment tracking for XDP
net/mlx5: Query hca_cap_2 only when supported
net/mlx5e: TC, CT: Offload ct clear only once
net/mlx5e: Check for NOT_READY flag state after locking
net/mlx5: Register a unique thermal zone per device
net/mlx5e: RX, Fix flush and close release flow of regular rq for legacy rq
net/mlx5e: fix memory leak in mlx5e_ptp_open
net/mlx5e: fix memory leak in mlx5e_fs_tt_redirect_any_create
net/mlx5e: fix double free in mlx5e_destroy_flow_table
====================
Link: https://lore.kernel.org/r/20230705175757.284614-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This switch implements Hold/Release in a strange way, with no control
from the user as required by IEEE 802.1Q-2018 through Set-And-Hold-MAC
and Set-And-Release-MAC, but rather, it emits HOLD requests implicitly
based on the schedule.
Namely, when the gate of a preemptible TC is about to close (actually
QSYS::PREEMPTION_CFG.HOLD_ADVANCE octet times in advance of this event),
the QSYS seems to emit a HOLD request pulse towards the MAC which
preempts the currently transmitted packet, and further packets are held
back in the queue system.
This allows large frames to be squeezed through small time slots,
because HOLD requests initiated by the gate events result in the frame
being segmented in multiple fragments, the bit time of which is equal to
the size of the time slot.
It has been reported that the vsc9959_tas_guard_bands_update() logic
breaks this, because it doesn't take preemptible TCs into account, and
enables oversized frame dropping when the time slot doesn't allow a full
MTU to be sent, but it does allow 2*minFragSize to be sent (128B).
Packets larger than 128B are dropped instead of being sent in multiple
fragments.
Confusingly, the manual says:
| For guard band, SDU calculation of a traffic class of a port, if
| preemption is enabled (through 'QSYS::PREEMPTION_CFG.P_QUEUES') then
| QSYS::PREEMPTION_CFG.HOLD_ADVANCE is used, otherwise
| QSYS::QMAXSDU_CFG_*.QMAXSDU_* is used.
but this only refers to the static guard band durations, and the
QMAXSDU_CFG_* registers have dual purpose - the other being oversized
frame dropping, which takes place irrespective of whether frames are
preemptible or express.
So, to fix the problem, we need to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and modify the guard
band logic to consider a different (lower) oversize limit for
preemptible traffic classes.
Fixes: 403ffc2c34 ("net: mscc: ocelot: add support for preemptible traffic classes")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-4-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In a future commit we will have to call vsc9959_tas_guard_bands_update()
from ocelot_port_update_active_preemptible_tcs(), and that will be
impossible due to the AB/BA locking dependencies between
ocelot->tas_lock and ocelot->fwd_domain_lock.
Just like we did in commit 3ff468ef98 ("net: mscc: ocelot: remove
struct ocelot_mm_state :: lock"), the only solution is to expand the
scope of ocelot->fwd_domain_lock for it to also serialize changes made
to the Time-Aware Shaper, because those will have to result in a
recalculation of cut-through TCs, which is something that depends on the
forwarding domain.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Message-ID: <20230705104422.49025-2-vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If we boot with mvneta.txq_number=1, the txq_map is set incorrectly:
MVNETA_CPU_TXQ_ACCESS(1) refers to TX queue 1, but only TX queue 0 is
initialized. Fix this.
Fixes: 50bf8cb6fc ("net: mvneta: Configure XPS support")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://lore.kernel.org/r/20230705053712.3914-1-klaus.kudielka@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=9yzk
-----END PGP SIGNATURE-----
Merge tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth, bpf and wireguard.
Current release - regressions:
- nvme-tcp: fix comma-related oops after sendpage changes
Current release - new code bugs:
- ptp: make max_phase_adjustment sysfs device attribute invisible
when not supported
Previous releases - regressions:
- sctp: fix potential deadlock on &net->sctp.addr_wq_lock
- mptcp:
- ensure subflow is unhashed before cleaning the backlog
- do not rely on implicit state check in mptcp_listen()
Previous releases - always broken:
- net: fix net_dev_start_xmit trace event vs skb_transport_offset()
- Bluetooth:
- fix use-bdaddr-property quirk
- L2CAP: fix multiple UaFs
- ISO: use hci_sync for setting CIG parameters
- hci_event: fix Set CIG Parameters error status handling
- hci_event: fix parsing of CIS Established Event
- MGMT: fix marking SCAN_RSP as not connectable
- wireguard: queuing: use saner cpu selection wrapping
- sched: act_ipt: various bug fixes for iptables <> TC interactions
- sched: act_pedit: add size check for TCA_PEDIT_PARMS_EX
- dsa: fixes for receiving PTP packets with 8021q and sja1105 tagging
- eth: sfc: fix null-deref in devlink port without MAE access
- eth: ibmvnic: do not reset dql stats on NON_FATAL err
Misc:
- xsk: honor SO_BINDTODEVICE on bind"
* tag 'net-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (70 commits)
nfp: clean mc addresses in application firmware when closing port
selftests: mptcp: pm_nl_ctl: fix 32-bit support
selftests: mptcp: depend on SYN_COOKIES
selftests: mptcp: userspace_pm: report errors with 'remove' tests
selftests: mptcp: userspace_pm: use correct server port
selftests: mptcp: sockopt: return error if wrong mark
selftests: mptcp: sockopt: use 'iptables-legacy' if available
selftests: mptcp: connect: fail if nft supposed to work
mptcp: do not rely on implicit state check in mptcp_listen()
mptcp: ensure subflow is unhashed before cleaning the backlog
s390/qeth: Fix vipa deletion
octeontx-af: fix hardware timestamp configuration
net: dsa: sja1105: always enable the send_meta options
net: dsa: tag_sja1105: fix MAC DA patching from meta frames
net: Replace strlcpy with strscpy
pptp: Fix fib lookup calls.
mlxsw: spectrum_router: Fix an IS_ERR() vs NULL check
net/sched: act_pedit: Add size check for TCA_PEDIT_PARMS_EX
xsk: Honor SO_BINDTODEVICE on bind
ptp: Make max_phase_adjustment sysfs device attribute invisible when not supported
...
I225/6 hardware can be programmed to start PPS output once
the time in Target Time registers is reached. The time
programmed in these registers should always be into future.
Only then PPS output is triggered when SYSTIM register
reaches the programmed value. There are two modes in i225/6
hardware to program PPS, pulse and clock mode.
There were issues reported where PPS is not generated when
start time is in past.
Example 1, "echo 0 0 0 2 0 > /sys/class/ptp/ptp0/period"
In the current implementation, a value of '0' is programmed
into Target time registers and PPS output is in pulse mode.
Eventually an interrupt which is triggered upon SYSTIM
register reaching Target time is not fired. Thus no PPS
output is generated.
Example 2, "echo 0 0 0 1 0 > /sys/class/ptp/ptp0/period"
Above case, a value of '0' is programmed into Target time
registers and PPS output is in clock mode. Here, HW tries to
catch-up the current time by incrementing Target Time
register. This catch-up time seem to vary according to
programmed PPS period time as per the HW design. In my
experiments, the delay ranged between few tens of seconds to
few minutes. The PPS output is only generated after the
Target time register reaches current time.
In my experiments, I also observed PPS stopped working with
below test and could not recover until module is removed and
loaded again.
1) echo 0 <future time> 0 1 0 > /sys/class/ptp/ptp1/period
2) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
3) echo 0 0 0 1 0 > /sys/class/ptp/ptp1/period
After this PPS did not work even if i re-program with proper
values. I could only get this back working by reloading the
driver.
This patch takes care of calculating and programming
appropriate future time value into Target Time registers.
Fixes: 5e91c72e56 ("igc: Fix PPS delta between two synchronized end-points")
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Reviewed-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
