On TI K3 am64x platform the issue with RX IRQ is observed - it's become
disabled forever after .ndo_stop(). The K3 CPSW driver manipulates RX IRQ
by using standard Linux enable_irq()/disable_irq_nosync() API as there is
no IRQ enable/disable options in CPSW HW itself, as result during
.ndo_stop() following sequence happens
phy_stop()
teardown TX/RX channels
wait for TX tdown complete
napi_disable(TX)
clean up TX channels
(a)
napi_disable(RX)
At point (a) it's not possible to predict if RX IRQ was triggered or not.
if RX IRQ was triggered then it also not possible to definitely say if RX
NAPI was run or only scheduled and immediately canceled by
napi_disable(RX). Actually the last case causes RX IRQ to be permanently
disabled.
Another observed issue is that RX IRQ enable counter become unbalanced if
(gro_flush_timeout =! 0) while (napi_defer_hard_irqs == 0):
Unbalanced enable for IRQ 44
WARNING: CPU: 0 PID: 10 at ../kernel/irq/manage.c:776 __enable_irq+0x38/0x80
__enable_irq+0x38/0x80
enable_irq+0x54/0xb0
am65_cpsw_nuss_rx_poll+0x2f4/0x368
__napi_poll+0x34/0x1b8
net_rx_action+0xe4/0x220
_stext+0x11c/0x284
run_ksoftirqd+0x4c/0x60
To avoid above issues introduce flag indicating if RX was actually disabled
before enabling it in am65_cpsw_nuss_rx_poll() and restore RX IRQ state in
.ndo_open()
Fixes: 4f7cce2724 ("net: ethernet: ti: am65-cpsw: add support for am64x cpsw3g")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hence all users of davinci_cpdma switched to skb_put_padto() the frame
padding can be removed from it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use skb_put_padto() instead of skb_padto() so skb->len also got updated, as
preparation for further removing frame padding from cpdma.
It also makes xmit path more clear and linear.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build failure in drivers/net/wwan/mhi_wwan_mbim.c:
add missing parameter (0, assuming we don't want buffer pre-alloc).
Conflict in drivers/net/dsa/sja1105/sja1105_main.c between:
589918df93 ("net: dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
0fac6aa098 ("net: dsa: sja1105: delete the best_effort_vlan_filtering mode")
Follow the instructions from the commit message of the former commit
- removed the if conditions. When looking at commit 589918df93 ("net:
dsa: sja1105: be stateless with FDB entries on SJA1105P/Q/R/S/SJA1110 too")
note that the mask_iotag fields get removed by the following patch.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The am65_cpsw_port_offload_fwd_mark_update() causes NULL exception crash
when there is at least one disabled port and any other port added to the
bridge first time.
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000858
pc : am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
lr : am65_cpsw_netdevice_event+0x8c/0xf0
Call trace:
am65_cpsw_port_offload_fwd_mark_update+0x54/0x68
notifier_call_chain+0x54/0x98
raw_notifier_call_chain+0x14/0x20
call_netdevice_notifiers_info+0x34/0x78
__netdev_upper_dev_link+0x1c8/0x290
netdev_master_upper_dev_link+0x1c/0x28
br_add_if+0x3f0/0x6d0 [bridge]
Fix it by adding proper check for port->ndev != NULL.
Fixes: 2934db9bcb ("net: ti: am65-cpsw-nuss: Add netdevice notifiers")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b0e8181762. Explicit
driver dependency on the bridge is no longer needed since
switchdev_bridge_port_{,un}offload() is no longer implemented by the
bridge driver but by switchdev.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of explicit offloading API in switchdev in commit
2f5dc00f7a ("net: bridge: switchdev: let drivers inform which bridge
ports are offloaded"), we started having Ethernet switch drivers calling
directly into a function exported by net/bridge/br_switchdev.c, which is
a function exported by the bridge driver.
This means that drivers that did not have an explicit dependency on the
bridge before, like cpsw and am65-cpsw, now do - otherwise it is not
possible to call a symbol exported by a driver that can be built as
module unless you are a module too.
There was an attempt to solve the dependency issue in the form of commit
b0e8181762 ("net: build all switchdev drivers as modules when the
bridge is a module"). Grygorii Strashko, however, says about it:
| In my opinion, the problem is a bit bigger here than just fixing the
| build :(
|
| In case, of ^cpsw the switchdev mode is kinda optional and in many
| cases (especially for testing purposes, NFS) the multi-mac mode is
| still preferable mode.
|
| There were no such tight dependency between switchdev drivers and
| bridge core before and switchdev serviced as independent, notification
| based layer between them, so ^cpsw still can be "Y" and bridge can be
| "M". Now for mostly every kernel build configuration the CONFIG_BRIDGE
| will need to be set as "Y", or we will have to update drivers to
| support build with BRIDGE=n and maintain separate builds for
| networking vs non-networking testing. But is this enough? Wouldn't
| it cause 'chain reaction' required to add more and more "Y" options
| (like CONFIG_VLAN_8021Q)?
|
| PS. Just to be sure we on the same page - ARM builds will be forced
| (with this patch) to have CONFIG_TI_CPSW_SWITCHDEV=m and so all our
| automation testing will just fail with omap2plus_defconfig.
In the light of this, it would be desirable for some configurations to
avoid dependencies between switchdev drivers and the bridge, and have
the switchdev mode as completely optional within the driver.
Arnd Bergmann also tried to write a patch which better expressed the
build time dependency for Ethernet switch drivers where the switchdev
support is optional, like cpsw/am65-cpsw, and this made the drivers
follow the bridge (compile as module if the bridge is a module) only if
the optional switchdev support in the driver was enabled in the first
place:
https://patchwork.kernel.org/project/netdevbpf/patch/20210802144813.1152762-1-arnd@kernel.org/
but this still did not solve the fact that cpsw and am65-cpsw now must
be built as modules when the bridge is a module - it just expressed
correctly that optional dependency. But the new behavior is an apparent
regression from Grygorii's perspective.
So to support the use case where the Ethernet driver is built-in,
NET_SWITCHDEV (a bool option) is enabled, and the bridge is a module, we
need a framework that can handle the possible absence of the bridge from
the running system, i.e. runtime bloatware as opposed to build-time
bloatware.
Luckily we already have this framework, since switchdev has been using
it extensively. Events from the bridge side are transmitted to the
driver side using notifier chains - this was originally done so that
unrelated drivers could snoop for events emitted by the bridge towards
ports that are implemented by other drivers (think of a switch driver
with LAG offload that listens for switchdev events on a bonding/team
interface that it offloads).
There are also events which are transmitted from the driver side to the
bridge side, which again are modeled using notifiers.
SWITCHDEV_FDB_ADD_TO_BRIDGE is an example of this, and deals with
notifying the bridge that a MAC address has been dynamically learned.
So there is a precedent we can use for modeling the new framework.
The difference compared to SWITCHDEV_FDB_ADD_TO_BRIDGE is that the work
that the bridge needs to do when a port becomes offloaded is blocking in
its nature: replay VLANs, MDBs etc. The calling context is indeed
blocking (we are under rtnl_mutex), but the existing switchdev
notification chain that the bridge is subscribed to is only the atomic
one. So we need to subscribe the bridge to the blocking switchdev
notification chain too.
This patch:
- keeps the driver-side perception of the switchdev_bridge_port_{,un}offload
unchanged
- moves the implementation of switchdev_bridge_port_{,un}offload from
the bridge module into the switchdev module.
- makes everybody that is subscribed to the switchdev blocking notifier
chain "hear" offload & unoffload events
- makes the bridge driver subscribe and handle those events
- moves the bridge driver's handling of those events into 2 new
functions called br_switchdev_port_{,un}offload. These functions
contain in fact the core of the logic that was previously in
switchdev_bridge_port_{,un}offload, just that now we go through an
extra indirection layer to reach them.
Unlike all the other switchdev notification structures, the structure
used to carry the bridge port information, struct
switchdev_notifier_brport_info, does not contain a "bool handled".
This is because in the current usage pattern, we always know that a
switchdev bridge port offloading event will be handled by the bridge,
because the switchdev_bridge_port_offload() call was initiated by a
NETDEV_CHANGEUPPER event in the first place, where info->upper_dev is a
bridge. So if the bridge wasn't loaded, then the CHANGEUPPER event
couldn't have happened.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit that introduced devlink support released devlink resources in
wrong order, that made an unwind flow to be asymmetrical. In addition,
the am65-cpsw-nuss used internal to devlink core field - registered.
In order to fix the unwind flow and remove such access to the
registered field, rewrite the code to call devlink_port_unregister only
on registered ports.
Fixes: 58356eb31d ("net: ti: am65-cpsw-nuss: Add devlink support")
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, all drivers depend on the bool CONFIG_NET_SWITCHDEV, but only
the drivers that call some sort of function exported by the bridge, like
br_vlan_enabled() or whatever, have an extra dependency on CONFIG_BRIDGE.
Since the blamed commit, all switchdev drivers have a functional
dependency upon switchdev_bridge_port_{,un}offload(), which is a pair of
functions exported by the bridge module and not by the bridge-independent
part of CONFIG_NET_SWITCHDEV.
Problems appear when we have:
CONFIG_BRIDGE=m
CONFIG_NET_SWITCHDEV=y
CONFIG_TI_CPSW_SWITCHDEV=y
because cpsw, am65_cpsw and sparx5 will then be built-in but they will
call a symbol exported by a loadable module. This is not possible and
will result in the following build error:
drivers/net/ethernet/ti/cpsw_new.o: in function `cpsw_netdevice_event':
drivers/net/ethernet/ti/cpsw_new.c:1520: undefined reference to
`switchdev_bridge_port_offload'
drivers/net/ethernet/ti/cpsw_new.c:1537: undefined reference to
`switchdev_bridge_port_unoffload'
As mentioned, the other switchdev drivers don't suffer from this because
switchdev_bridge_port_offload() is not the first symbol exported by the
bridge that they are calling, so they already needed to deal with this
in the same way.
Fixes: 2f5dc00f7a ("net: bridge: switchdev: let drivers inform which bridge ports are offloaded")
Reported-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switchdevs to forward frames from the CPU in accordance with the
bridge configuration in the same way as is done between bridge
ports. This means that the bridge will only send a single skb towards
one of the ports under the switchdev's control, and expects the driver
to deliver the packet to all eligible ports in its domain.
Primarily this improves the performance of multicast flows with
multiple subscribers, as it allows the hardware to perform the frame
replication.
The basic flow between the driver and the bridge is as follows:
- When joining a bridge port, the switchdev driver calls
switchdev_bridge_port_offload() with tx_fwd_offload = true.
- The bridge sends offloadable skbs to one of the ports under the
switchdev's control using skb->offload_fwd_mark = true.
- The switchdev driver checks the skb->offload_fwd_mark field and lets
its FDB lookup select the destination port mask for this packet.
v1->v2:
- convert br_input_skb_cb::fwd_hwdoms to a plain unsigned long
- introduce a static key "br_switchdev_fwd_offload_used" to minimize the
impact of the newly introduced feature on all the setups which don't
have hardware that can make use of it
- introduce a check for nbp->flags & BR_FWD_OFFLOAD to optimize cache
line access
- reorder nbp_switchdev_frame_mark_accel() and br_handle_vlan() in
__br_forward()
- do not strip VLAN on egress if forwarding offload on VLAN-aware bridge
is being used
- propagate errors from .ndo_dfwd_add_station() if not EOPNOTSUPP
v2->v3:
- replace the solution based on .ndo_dfwd_add_station with a solution
based on switchdev_bridge_port_offload
- rename BR_FWD_OFFLOAD to BR_TX_FWD_OFFLOAD
v3->v4: rebase
v4->v5:
- make sure the static key is decremented on bridge port unoffload
- more function and variable renaming and comments for them:
br_switchdev_fwd_offload_used to br_switchdev_tx_fwd_offload
br_switchdev_accels_skb to br_switchdev_frame_uses_tx_fwd_offload
nbp_switchdev_frame_mark_tx_fwd to nbp_switchdev_frame_mark_tx_fwd_to_hwdom
nbp_switchdev_frame_mark_accel to nbp_switchdev_frame_mark_tx_fwd_offload
fwd_accel to tx_fwd_offload
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 4f2673b3a2 ("net: bridge: add helper to replay
port and host-joined mdb entries"), DSA has introduced some bridge
helpers that replay switchdev events (FDB/MDB/VLAN additions and
deletions) that can be lost by the switchdev drivers in a variety of
circumstances:
- an IP multicast group was host-joined on the bridge itself before any
switchdev port joined the bridge, leading to the host MDB entries
missing in the hardware database.
- during the bridge creation process, the MAC address of the bridge was
added to the FDB as an entry pointing towards the bridge device
itself, but with no switchdev ports being part of the bridge yet, this
local FDB entry would remain unknown to the switchdev hardware
database.
- a VLAN/FDB/MDB was added to a bridge port that is a LAG interface,
before any switchdev port joined that LAG, leading to the hardware
database missing those entries.
- a switchdev port left a LAG that is a bridge port, while the LAG
remained part of the bridge, and all FDB/MDB/VLAN entries remained
installed in the hardware database of the switchdev port.
Also, since commit 0d2cfbd41c ("net: bridge: ignore switchdev events
for LAG ports which didn't request replay"), DSA introduced a method,
based on a const void *ctx, to ensure that two switchdev ports under the
same LAG that is a bridge port do not see the same MDB/VLAN entry being
replayed twice by the bridge, once for every bridge port that joins the
LAG.
With so many ordering corner cases being possible, it seems unreasonable
to expect a switchdev driver writer to get it right from the first try.
Therefore, now that DSA has experimented with the bridge replay helpers
for a little bit, we can move the code to the bridge driver where it is
more readily available to all switchdev drivers.
To convert the switchdev object replay helpers from "pull mode" (where
the driver asks for them) to a "push mode" (where the bridge offers them
automatically), the biggest problem is that the bridge needs to be aware
when a switchdev port joins and leaves, even when the switchdev is only
indirectly a bridge port (for example when the bridge port is a LAG
upper of the switchdev).
Luckily, we already have a hook for that, in the form of the newly
introduced switchdev_bridge_port_offload() and
switchdev_bridge_port_unoffload() calls. These offer a natural place for
hooking the object addition and deletion replays.
Extend the above 2 functions with:
- pointers to the switchdev atomic notifier (for FDB replays) and the
blocking notifier (for MDB and VLAN replays).
- the "const void *ctx" argument required for drivers to be able to
disambiguate between which port is targeted, when multiple ports are
lowers of the same LAG that is a bridge port. Most of the drivers pass
NULL to this argument, except the ones that support LAG offload and have
the proper context check already in place in the switchdev blocking
notifier handler.
Also unexport the replay helpers, since nobody except the bridge calls
them directly now.
Note that:
(a) we abuse the terminology slightly, because FDB entries are not
"switchdev objects", but we count them as objects nonetheless.
With no direct way to prove it, I think they are not modeled as
switchdev objects because those can only be installed by the bridge
to the hardware (as opposed to FDB entries which can be propagated
in the other direction too). This is merely an abuse of terms, FDB
entries are replayed too, despite not being objects.
(b) the bridge does not attempt to sync port attributes to newly joined
ports, just the countable stuff (the objects). The reason for this
is simple: no universal and symmetric way to sync and unsync them is
known. For example, VLAN filtering: what to do on unsync, disable or
leave it enabled? Similarly, STP state, ageing timer, etc etc. What
a switchdev port does when it becomes standalone again is not really
up to the bridge's competence, and the driver should deal with it.
On the other hand, replaying deletions of switchdev objects can be
seen a matter of cleanup and therefore be treated by the bridge,
hence this patch.
We make the replay helpers opt-in for drivers, because they might not
bring immediate benefits for them:
- nbp_vlan_init() is called _after_ netdev_master_upper_dev_link(),
so br_vlan_replay() should not do anything for the new drivers on
which we call it. The existing drivers where there was even a slight
possibility for there to exist a VLAN on a bridge port before they
join it are already guarded against this: mlxsw and prestera deny
joining LAG interfaces that are members of a bridge.
- br_fdb_replay() should now notify of local FDB entries, but I patched
all drivers except DSA to ignore these new entries in commit
2c4eca3ef7 ("net: bridge: switchdev: include local flag in FDB
notifications"). Driver authors can lift this restriction as they
wish, and when they do, they can also opt into the FDB replay
functionality.
- br_mdb_replay() should fix a real issue which is described in commit
4f2673b3a2 ("net: bridge: add helper to replay port and host-joined
mdb entries"). However most drivers do not offload the
SWITCHDEV_OBJ_ID_HOST_MDB to see this issue: only cpsw and am65_cpsw
offload this switchdev object, and I don't completely understand the
way in which they offload this switchdev object anyway. So I'll leave
it up to these drivers' respective maintainers to opt into
br_mdb_replay().
So most of the drivers pass NULL notifier blocks for the replay helpers,
except:
- dpaa2-switch which was already acked/regression-tested with the
helpers enabled (and there isn't much of a downside in having them)
- ocelot which already had replay logic in "pull" mode
- DSA which already had replay logic in "pull" mode
An important observation is that the drivers which don't currently
request bridge event replays don't even have the
switchdev_bridge_port_{offload,unoffload} calls placed in proper places
right now. This was done to avoid unnecessary rework for drivers which
might never even add support for this. For driver writers who wish to
add replay support, this can be used as a tentative placement guide:
https://patchwork.kernel.org/project/netdevbpf/patch/20210720134655.892334-11-vladimir.oltean@nxp.com/
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
On reception of an skb, the bridge checks if it was marked as 'already
forwarded in hardware' (checks if skb->offload_fwd_mark == 1), and if it
is, it assigns the source hardware domain of that skb based on the
hardware domain of the ingress port. Then during forwarding, it enforces
that the egress port must have a different hardware domain than the
ingress one (this is done in nbp_switchdev_allowed_egress).
Non-switchdev drivers don't report any physical switch id (neither
through devlink nor .ndo_get_port_parent_id), therefore the bridge
assigns them a hardware domain of 0, and packets coming from them will
always have skb->offload_fwd_mark = 0. So there aren't any restrictions.
Problems appear due to the fact that DSA would like to perform software
fallback for bonding and team interfaces that the physical switch cannot
offload.
+-- br0 ---+
/ / | \
/ / | \
/ | | bond0
/ | | / \
swp0 swp1 swp2 swp3 swp4
There, it is desirable that the presence of swp3 and swp4 under a
non-offloaded LAG does not preclude us from doing hardware bridging
beteen swp0, swp1 and swp2. The bandwidth of the CPU is often times high
enough that software bridging between {swp0,swp1,swp2} and bond0 is not
impractical.
But this creates an impossible paradox given the current way in which
port hardware domains are assigned. When the driver receives a packet
from swp0 (say, due to flooding), it must set skb->offload_fwd_mark to
something.
- If we set it to 0, then the bridge will forward it towards swp1, swp2
and bond0. But the switch has already forwarded it towards swp1 and
swp2 (not to bond0, remember, that isn't offloaded, so as far as the
switch is concerned, ports swp3 and swp4 are not looking up the FDB,
and the entire bond0 is a destination that is strictly behind the
CPU). But we don't want duplicated traffic towards swp1 and swp2, so
it's not ok to set skb->offload_fwd_mark = 0.
- If we set it to 1, then the bridge will not forward the skb towards
the ports with the same switchdev mark, i.e. not to swp1, swp2 and
bond0. Towards swp1 and swp2 that's ok, but towards bond0? It should
have forwarded the skb there.
So the real issue is that bond0 will be assigned the same hardware
domain as {swp0,swp1,swp2}, because the function that assigns hardware
domains to bridge ports, nbp_switchdev_add(), recurses through bond0's
lower interfaces until it finds something that implements devlink (calls
dev_get_port_parent_id with bool recurse = true). This is a problem
because the fact that bond0 can be offloaded by swp3 and swp4 in our
example is merely an assumption.
A solution is to give the bridge explicit hints as to what hardware
domain it should use for each port.
Currently, the bridging offload is very 'silent': a driver registers a
netdevice notifier, which is put on the netns's notifier chain, and
which sniffs around for NETDEV_CHANGEUPPER events where the upper is a
bridge, and the lower is an interface it knows about (one registered by
this driver, normally). Then, from within that notifier, it does a bunch
of stuff behind the bridge's back, without the bridge necessarily
knowing that there's somebody offloading that port. It looks like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v
call_netdevice_notifiers
|
v
dsa_slave_netdevice_event
|
v
oh, hey! it's for me!
|
v
.port_bridge_join
What we do to solve the conundrum is to be less silent, and change the
switchdev drivers to present themselves to the bridge. Something like this:
ip link set swp0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | hardware domain for
v | this port, and zero
dsa_slave_netdevice_event | if I got nothing.
| |
v |
oh, hey! it's for me! |
| |
v |
.port_bridge_join |
| |
+------------------------+
switchdev_bridge_port_offload(swp0, swp0)
Then stacked interfaces (like bond0 on top of swp3/swp4) would be
treated differently in DSA, depending on whether we can or cannot
offload them.
The offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge: Aye! I'll use this
call_netdevice_notifiers ^ ppid as the
| | switchdev mark for
v | bond0.
dsa_slave_netdevice_event | Coincidentally (or not),
| | bond0 and swp0, swp1, swp2
v | all have the same switchdev
hmm, it's not quite for me, | mark now, since the ASIC
but my driver has already | is able to forward towards
called .port_lag_join | all these ports in hw.
for it, because I have |
a port with dp->lag_dev == bond0. |
| |
v |
.port_bridge_join |
for swp3 and swp4 |
| |
+------------------------+
switchdev_bridge_port_offload(bond0, swp3)
switchdev_bridge_port_offload(bond0, swp4)
And the non-offload case:
ip link set bond0 master br0
|
v
br_add_if() calls netdev_master_upper_dev_link()
|
v bridge waiting:
call_netdevice_notifiers ^ huh, switchdev_bridge_port_offload
| | wasn't called, okay, I'll use a
v | hwdom of zero for this one.
dsa_slave_netdevice_event : Then packets received on swp0 will
| : not be software-forwarded towards
v : swp1, but they will towards bond0.
it's not for me, but
bond0 is an upper of swp3
and swp4, but their dp->lag_dev
is NULL because they couldn't
offload it.
Basically we can draw the conclusion that the lowers of a bridge port
can come and go, so depending on the configuration of lowers for a
bridge port, it can dynamically toggle between offloaded and unoffloaded.
Therefore, we need an equivalent switchdev_bridge_port_unoffload too.
This patch changes the way any switchdev driver interacts with the
bridge. From now on, everybody needs to call switchdev_bridge_port_offload
and switchdev_bridge_port_unoffload, otherwise the bridge will treat the
port as non-offloaded and allow software flooding to other ports from
the same ASIC.
Note that these functions lay the ground for a more complex handshake
between switchdev drivers and the bridge in the future.
For drivers that will request a replay of the switchdev objects when
they offload and unoffload a bridge port (DSA, dpaa2-switch, ocelot), we
place the call to switchdev_bridge_port_unoffload() strategically inside
the NETDEV_PRECHANGEUPPER notifier's code path, and not inside
NETDEV_CHANGEUPPER. This is because the switchdev object replay helpers
need the netdev adjacency lists to be valid, and that is only true in
NETDEV_PRECHANGEUPPER.
Cc: Vadym Kochan <vkochan@marvell.com>
Cc: Taras Chornyi <tchornyi@marvell.com>
Cc: Ioana Ciornei <ioana.ciornei@nxp.com>
Cc: Lars Povlsen <lars.povlsen@microchip.com>
Cc: Steen Hegelund <Steen.Hegelund@microchip.com>
Cc: UNGLinuxDriver@microchip.com
Cc: Claudiu Manoil <claudiu.manoil@nxp.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch: regression
Acked-by: Ioana Ciornei <ioana.ciornei@nxp.com> # dpaa2-switch
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com> # ocelot-switch
Signed-off-by: David S. Miller <davem@davemloft.net>
priv is netdev private data and it cannot be
used after free_netdev() call. Using priv after free_netdev()
can cause UAF bug. Fix it by moving free_netdev() at the end of the
function.
Fixes: 1e0a8b13d3 ("tlan: cancel work at remove path")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 12 day(s) which contain
a total of 56 files changed, 394 insertions(+), 380 deletions(-).
The main changes are:
1) XDP driver RCU cleanups, from Toke Høiland-Jørgensen and Paul E. McKenney.
2) Fix bpf_skb_change_proto() IPv4/v6 GSO handling, from Maciej Żenczykowski.
3) Fix false positive kmemleak report for BPF ringbuf alloc, from Rustam Kovhaev.
4) Fix x86 JIT's extable offset calculation for PROBE_LDX NULL, from Ravi Bangoria.
5) Enable libbpf fallback probing with tracing under RHEL7, from Jonathan Edwards.
6) Clean up x86 JIT to remove unused cnt tracking from EMIT macro, from Jiri Olsa.
7) Netlink cleanups for libbpf to please Coverity, from Kumar Kartikeya Dwivedi.
8) Allow to retrieve ancestor cgroup id in tracing programs, from Namhyung Kim.
9) Fix lirc BPF program query to use user-provided prog_cnt, from Sean Young.
10) Add initial libbpf doc including generated kdoc for its API, from Grant Seltzer.
11) Make xdp_rxq_info_unreg_mem_model() more robust, from Jakub Kicinski.
12) Fix up bpfilter startup log-level to info level, from Gary Lin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case where the driver asks for a replay of a certain type of
event (port object or attribute) for a bridge port that is a LAG, it may
do so because this port has just joined the LAG.
But there might already be other switchdev ports in that LAG, and it is
preferable that those preexisting switchdev ports do not act upon the
replayed event.
The solution is to add a context to switchdev events, which is NULL most
of the time (when the bridge layer initiates the call) but which can be
set to a value controlled by the switchdev driver when a replay is
requested. The driver can then check the context to figure out if all
ports within the LAG should act upon the switchdev event, or just the
ones that match the context.
We have to modify all switchdev_handle_* helper functions as well as the
prototypes in the drivers that use these helpers too, because these
helpers hide the underlying struct switchdev_notifier_info from us and
there is no way to retrieve the context otherwise.
The context structure will be populated and used in later patches.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw driver has rcu_read_lock()/rcu_read_unlock() pairs around XDP
program invocations. However, the actual lifetime of the objects referred
by the XDP program invocation is longer, all the way through to the call to
xdp_do_flush(), making the scope of the rcu_read_lock() too small. This
turns out to be harmless because it all happens in a single NAPI poll
cycle (and thus under local_bh_disable()), but it makes the rcu_read_lock()
misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: linux-omap@vger.kernel.org
Link: https://lore.kernel.org/bpf/20210624160609.292325-20-toke@redhat.com
When changing number of TX queues using ethtool:
# ethtool -L eth0 tx 1
[ 135.301047] Unable to handle kernel paging request at virtual address 00000000af5d0000
[...]
[ 135.525128] Call trace:
[ 135.525142] dma_release_from_dev_coherent+0x2c/0xb0
[ 135.525148] dma_free_attrs+0x54/0xe0
[ 135.525156] k3_cppi_desc_pool_destroy+0x50/0xa0
[ 135.525164] am65_cpsw_nuss_remove_tx_chns+0x88/0xdc
[ 135.525171] am65_cpsw_set_channels+0x3c/0x70
[...]
This is because k3_cppi_desc_pool_destroy() which is called after
k3_udma_glue_release_tx_chn() in am65_cpsw_nuss_remove_tx_chns()
references struct device that is unregistered at the end of
k3_udma_glue_release_tx_chn()
Therefore the right order is to call k3_cppi_desc_pool_destroy() and
destroy desc pool before calling k3_udma_glue_release_tx_chn().
Fix this throughout the driver.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code and avoid a null-ptr-deref by checking 'res' in it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/ti/cpsw_ale.c:88: warning: expecting prototype for struct ale_dev_id. Prototype was for struct cpsw_ale_dev_id instead
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'ret' is known to be 0 here.
The expected error code is stored in 'tx_pipe->dma_queue', so use it
instead.
While at it, switch from %d to %pe which is more user friendly.
Fixes: 84640e27f2 ("net: netcp: Add Keystone NetCP core ethernet driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit-masks used for the TXERRCH and RXERRCH (tx and rx error channels)
are incorrect and always lead to a zero result. The mask values are
currently the incorrect post-right shifted values, fix this by setting
them to the currect values.
(I double checked these against the TMS320TCI6482 data sheet, section
5.30, page 127 to ensure I had the correct mask values for the TXERRCH
and RXERRCH fields in the MACSTATUS register).
Addresses-Coverity: ("Operands don't affect result")
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in bugfix commit 6ab4c3117a ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/
the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.
Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to change the current ndo_xdp_xmit drop semantics because it will
allow us to implement better queue overflow handling. This is working
towards the larger goal of a XDP TX queue-hook. Move XDP_REDIRECT error
path handling from each XDP ethernet driver to devmap code. According to
the new APIs, the driver running the ndo_xdp_xmit pointer, will break tx
loop whenever the hw reports a tx error and it will just return to devmap
caller the number of successfully transmitted frames. It will be devmap
responsibility to free dropped frames.
Move each XDP ndo_xdp_xmit capable driver to the new APIs:
- veth
- virtio-net
- mvneta
- mvpp2
- socionext
- amazon ena
- bnxt
- freescale (dpaa2, dpaa)
- xen-frontend
- qede
- ice
- igb
- ixgbe
- i40e
- mlx5
- ti (cpsw, cpsw-new)
- tun
- sfc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Edward Cree <ecree.xilinx@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Shay Agroskin <shayagr@amazon.com>
Link: https://lore.kernel.org/bpf/ed670de24f951cfd77590decf0229a0ad7fd12f6.1615201152.git.lorenzo@kernel.org
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build
host fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device(). In preparation for
this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
-----BEGIN PGP SIGNATURE-----
iQJEBAABCgAuFiEEktVUI4SxYhzZyEuo+vtdtY28YcMFAmAz1GEQHHJvYmhAa2Vy
bmVsLm9yZwAKCRD6+121jbxhw55/D/955O2f5Gjp7bXvdoSucZtks/lqlC/eIAAw
An5pjBL+o1urXsvafEMYemwmnwq/U4vy0aJRoAK1+MiI4masb56ET0KN5LsOudki
b3M/O16RqGF31+blWyoxseZnZh6KsKzIRoE5XAtbr/QAnpdI0/5BgGoWSWYtDk2v
LddL650/BieyvzdnFTLWCMAxd6DW0P9SI+8N3E+XlxAWCYQrLCqVELHbkrxAGCuN
CggHIIiNf2K7z4UopVsGjnUwML9YRHXc9wOpF1c4CBrLu9TfDvdQ4OnNcnxcl/Sp
E2FTHG0jSVm3VJRBbk4e68uvt3HrJJWsYnMtu2QTweGC/GbeUr9LJ0MIbSwp+rsL
FEqCMFWOniq27eJBk6jHckaoBl93AHQlIGdJR/pFAi9Ijt32tUdVG5kqD/Tl+xKm
njPcjVjWilr2ssfZ4tUggzPp2fjrau88ZS8qLja31vElzvULeA67KjEtG0RZAtwg
ywfATiCaT096pR9v2VYuL/5NNnZFxHx3hWsOH1rcsyPk0BLguU3dkrAn28XBVQFd
cOPfR3T/wsT0wHDht2aXPSM0hBiejFmvLhebGuJN9lqG+Pc1f87xiCT3pM7wymtJ
iqTMrQ7dUgjQgU91PjatdB17tlnGHe0hh8AiuhQoPgOprpRKszG+rBFJLG3yRnl7
QmLZnQTIhw==
=9V4A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Sync dtc to upstream version v1.6.0-51-g183df9e9c2b9 and build host
fdtoverlay
- Add kbuild support to build DT overlays (%.dtbo)
- Drop NULLifying match table in of_match_device().
In preparation for this, there are several driver cleanups to use
(of_)?device_get_match_data().
- Drop pointless wrappers from DT struct device API
- Convert USB binding schemas to use graph schema and remove old plain
text graph binding doc
- Convert spi-nor and v3d GPU bindings to DT schema
- Tree wide schema fixes for if/then schemas, array size constraints,
and undocumented compatible strings in examples
- Handle 'no-map' correctly for already reserved memblock regions
* tag 'devicetree-for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
driver core: platform: Drop of_device_node_put() wrapper
of: Remove of_dev_{get,put}()
dt-bindings: usb: Change descibe to describe in usbmisc-imx.txt
dt-bindings: can: rcar_canfd: Group tuples in pin control properties
dt-bindings: power: renesas,apmu: Group tuples in cpus properties
dt-bindings: mtd: spi-nor: Convert to DT schema format
dt-bindings: Use portable sort for version cmp
dt-bindings: ethernet-controller: fix fixed-link specification
dt-bindings: irqchip: Add node name to PRUSS INTC
dt-bindings: interconnect: Fix the expected number of cells
dt-bindings: Fix errors in 'if' schemas
dt-bindings: iommu: renesas,ipmmu-vmsa: Make 'power-domains' conditionally required
dt-bindings: Fix undocumented compatible strings in examples
kbuild: Add support to build overlays (%.dtbo)
scripts: dtc: Remove the unused fdtdump.c file
scripts: dtc: Build fdtoverlay tool
scripts/dtc: Update to upstream version v1.6.0-51-g183df9e9c2b9
scripts: dtc: Fetch fdtoverlay.c from external DTC project
dt-bindings: thermal: sun8i: Fix misplaced schema keyword in compatible strings
dt-bindings: iio: dac: Fix AD5686 references
...
This switchdev attribute offers a counterproductive API for a driver
writer, because although br_switchdev_set_port_flag gets passed a
"flags" and a "mask", those are passed piecemeal to the driver, so while
the PRE_BRIDGE_FLAGS listener knows what changed because it has the
"mask", the BRIDGE_FLAGS listener doesn't, because it only has the final
value. But certain drivers can offload only certain combinations of
settings, like for example they cannot change unicast flooding
independently of multicast flooding - they must be both on or both off.
The way the information is passed to switchdev makes drivers not
expressive enough, and unable to reject this request ahead of time, in
the PRE_BRIDGE_FLAGS notifier, so they are forced to reject it during
the deferred BRIDGE_FLAGS attribute, where the rejection is currently
ignored.
This patch also changes drivers to make use of the "mask" field for edge
detection when possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a struct switchdev_attr is notified through switchdev, there is no
way to report informational messages, unlike for struct switchdev_obj.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
J721e, J7200 and AM64 have multi port switches which can work in multi
mac mode and in switch mode. Add support for configuring this HW in
switch mode using devlink and switchdev notifiers.
Support is similar to existing CPSW switchdev implementation of TI's 32 bit
platform like AM33/AM43/AM57.
To enable switch mode:
devlink dev param set platform/8000000.ethernet name switch_mode value true cmode runtime
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence AM65 CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register netdevice notifiers in order to receive notification when
individual MAC ports are added to the HW bridge.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM65 NUSS ethernet switch on K3 devices can be configured to work either
in independent mac mode where each port acts as independent network
interface (multi mac) or switch mode.
Add devlink hooks to provide a way to switch b/w these modes.
Rationale to use devlink instead of defaulting to bridge mode is that
SoC use cases require to support multiple independent MAC ports with no
switching so that users can use software bridges with multi-mac
configuration (e.g: to support LAG, HSR/PRP, etc). Also, switching
between multi mac and switch mode requires significant Port and ALE
reconfiguration, therefore is easier to be made as part of mode change
devlink hooks. It also allows to keep user interface similar to what
was implemented for the previous generation of TI CPSW IP
(on AM33/AM43/AM57 SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align netdevice statistics when the device is running in XDP mode
to other upstream drivers. In particular report to user-space rx
packets even if they are not forwarded to the networking stack
(XDP_PASS) but if they are redirected (XDP_REDIRECT), dropped (XDP_DROP)
or sent back using the same interface (XDP_TX). This patch allows the
system administrator to verify the device is receiving data correctly.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/a457cb17dd9c58c116d64ee34c354b2e89c0ff8f.1612375372.git.lorenzo@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the more modern API to get the match data out of the of match table.
This saves some code, lines, and nicely avoids referencing the match
table when it is undefined with configurations where CONFIG_OF=n.
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: <linux-omap@vger.kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210123034428.2841052-3-swboyd@chromium.org
The TI AM64x SoCs Gigabit Ethernet Switch subsystem (CPSW3g NUSS) has three
ports (2 ext. ports) and provides Ethernet packet communication for the
device and can be configured in multi port mode or as an Ethernet switch.
This patch adds support for the corresponding CPSW3g version.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The AM642x CPSW3g is similar to j721e-cpswxg except its ALE table size is
512 entries. Add entry for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the glue layer's functions to convert the dma_addr_t to and from CPPI5
address (with the ASEL bits), which should be used within the descriptors
and data buffers.
- Per channel coherency support
The DMAs use the 'ASEL' bits to select data and configuration fetch path.
The ASEL bits are placed at the unused parts of any address field used by
the DMAs (pointers to descriptors, addresses in descriptors, ring base
addresses). The ASEL is not part of the address (the DMAs can address
48bits). Individual channels can be configured to be coherent (via ACP
port) or non coherent individually by configuring the ASEL to appropriate
value.
[1] https://lore.kernel.org/patchwork/cover/1350756/
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For DMA API the DMA device should be used as cpsw does not accesses to
descriptors or data buffers in any ways. The DMA does.
Also, drop dma_coerce_mask_and_coherent() setting on CPSW device, as it
should be done by DMA driver which does data movement.
This is required for adding AM64x CPSW3g support where DMA coherency
supported per DMA channel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/ti/am65-cpts.c:736: warning: Function parameter or member 'en' not described in 'am65_cpts_rx_enable'
drivers/net/ethernet/ti/am65-cpts.c:736: warning: Excess function parameter 'skb' description in 'am65_cpts_rx_enable'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/ti/am65-cpsw-qos.c:364: warning: Function parameter or member 'ndev' not described in 'am65_cpsw_timer_set'
drivers/net/ethernet/ti/am65-cpsw-qos.c:364: warning: Function parameter or member 'est_new' not described in 'am65_cpsw_timer_set'
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port attributes were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
attribute notifier structures, and converts drivers to not look at this
member.
In part, this patch contains a revert of my previous commit 2e554a7a5d
("net: dsa: propagate switchdev vlan_filtering prepare phase to
drivers").
For the most part, the conversion was trivial except for:
- Rocker's world implementation based on Broadcom OF-DPA had an odd
implementation of ofdpa_port_attr_bridge_flags_set. The conversion was
done mechanically, by pasting the implementation twice, then only
keeping the code that would get executed during prepare phase on top,
then only keeping the code that gets executed during the commit phase
on bottom, then simplifying the resulting code until this was obtained.
- DSA's offloading of STP state, bridge flags, VLAN filtering and
multicast router could be converted right away. But the ageing time
could not, so a shim was introduced and this was left for a further
commit.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Reviewed-by: Linus Walleij <linus.walleij@linaro.org> # RTL8366RB
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the introduction of the switchdev API, port objects were
transmitted to drivers for offloading using a two-step transactional
model, with a prepare phase that was supposed to catch all errors, and a
commit phase that was supposed to never fail.
Some classes of failures can never be avoided, like hardware access, or
memory allocation. In the latter case, merely attempting to move the
memory allocation to the preparation phase makes it impossible to avoid
memory leaks, since commit 91cf8eceff ("switchdev: Remove unused
transaction item queue") which has removed the unused mechanism of
passing on the allocated memory between one phase and another.
It is time we admit that separating the preparation from the commit
phase is something that is best left for the driver to decide, and not
something that should be baked into the API, especially since there are
no switchdev callers that depend on this.
This patch removes the struct switchdev_trans member from switchdev port
object notifier structures, and converts drivers to not look at this
member.
Where driver conversion is trivial (like in the case of the Marvell
Prestera driver, NXP DPAA2 switch, TI CPSW, and Rocker drivers), it is
done in this patch.
Where driver conversion needs more attention (DSA, Mellanox Spectrum),
the conversion is left for subsequent patches and here we only fake the
prepare/commit phases at a lower level, just not in the switchdev
notifier itself.
Where the code has a natural structure that is best left alone as a
preparation and a commit phase (as in the case of the Ocelot switch),
that structure is left in place, just made to not depend upon the
switchdev transactional model.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The call path of a switchdev VLAN addition to the bridge looks something
like this today:
nbp_vlan_init
| __br_vlan_set_default_pvid
| | |
| | br_afspec |
| | | |
| | v |
| | br_process_vlan_info |
| | | |
| | v |
| | br_vlan_info |
| | / \ /
| | / \ /
| | / \ /
| | / \ /
v v v v v
nbp_vlan_add br_vlan_add ------+
| ^ ^ | |
| / | | |
| / / / |
\ br_vlan_get_master/ / v
\ ^ / / br_vlan_add_existing
\ | / / |
\ | / / /
\ | / / /
\ | / / /
\ | / / /
v | | v /
__vlan_add /
/ | /
/ | /
v | /
__vlan_vid_add | /
\ | /
v v v
br_switchdev_port_vlan_add
The ranges UAPI was introduced to the bridge in commit bdced7ef78
("bridge: support for multiple vlans and vlan ranges in setlink and
dellink requests") (Jan 10 2015). But the VLAN ranges (parsed in br_afspec)
have always been passed one by one, through struct bridge_vlan_info
tmp_vinfo, to br_vlan_info. So the range never went too far in depth.
Then Scott Feldman introduced the switchdev_port_bridge_setlink function
in commit 47f8328bb1 ("switchdev: add new switchdev bridge setlink").
That marked the introduction of the SWITCHDEV_OBJ_PORT_VLAN, which made
full use of the range. But switchdev_port_bridge_setlink was called like
this:
br_setlink
-> br_afspec
-> switchdev_port_bridge_setlink
Basically, the switchdev and the bridge code were not tightly integrated.
Then commit 41c498b935 ("bridge: restore br_setlink back to original")
came, and switchdev drivers were required to implement
.ndo_bridge_setlink = switchdev_port_bridge_setlink for a while.
In the meantime, commits such as 0944d6b5a2 ("bridge: try switchdev op
first in __vlan_vid_add/del") finally made switchdev penetrate the
br_vlan_info() barrier and start to develop the call path we have today.
But remember, br_vlan_info() still receives VLANs one by one.
Then Arkadi Sharshevsky refactored the switchdev API in 2017 in commit
29ab586c3d ("net: switchdev: Remove bridge bypass support from
switchdev") so that drivers would not implement .ndo_bridge_setlink any
longer. The switchdev_port_bridge_setlink also got deleted.
This refactoring removed the parallel bridge_setlink implementation from
switchdev, and left the only switchdev VLAN objects to be the ones
offloaded from __vlan_vid_add (basically RX filtering) and __vlan_add
(the latter coming from commit 9c86ce2c1a ("net: bridge: Notify about
bridge VLANs")).
That is to say, today the switchdev VLAN object ranges are not used in
the kernel. Refactoring the above call path is a bit complicated, when
the bridge VLAN call path is already a bit complicated.
Let's go off and finish the job of commit 29ab586c3d by deleting the
bogus iteration through the VLAN ranges from the drivers. Some aspects
of this feature never made too much sense in the first place. For
example, what is a range of VLANs all having the BRIDGE_VLAN_INFO_PVID
flag supposed to mean, when a port can obviously have a single pvid?
This particular configuration _is_ denied as of commit 6623c60dc2
("bridge: vlan: enforce no pvid flag in vlan ranges"), but from an API
perspective, the driver still has to play pretend, and only offload the
vlan->vid_end as pvid. And the addition of a switchdev VLAN object can
modify the flags of another, completely unrelated, switchdev VLAN
object! (a VLAN that is PVID will invalidate the PVID flag from whatever
other VLAN had previously been offloaded with switchdev and had that
flag. Yet switchdev never notifies about that change, drivers are
supposed to guess).
Nonetheless, having a VLAN range in the API makes error handling look
scarier than it really is - unwinding on errors and all of that.
When in reality, no one really calls this API with more than one VLAN.
It is all unnecessary complexity.
And despite appearing pretentious (two-phase transactional model and
all), the switchdev API is really sloppy because the VLAN addition and
removal operations are not paired with one another (you can add a VLAN
100 times and delete it just once). The bridge notifies through
switchdev of a VLAN addition not only when the flags of an existing VLAN
change, but also when nothing changes. There are switchdev drivers out
there who don't like adding a VLAN that has already been added, and
those checks don't really belong at driver level. But the fact that the
API contains ranges is yet another factor that prevents this from being
addressed in the future.
Of the existing switchdev pieces of hardware, it appears that only
Mellanox Spectrum supports offloading more than one VLAN at a time,
through mlxsw_sp_port_vlan_set. I have kept that code internal to the
driver, because there is some more bookkeeping that makes use of it, but
I deleted it from the switchdev API. But since the switchdev support for
ranges has already been de facto deleted by a Mellanox employee and
nobody noticed for 4 years, I'm going to assume it's not a biggie.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com> # switchdev and mlxsw
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CPTS driver registers PTP PHC clock when first netif is going up and
unregister it when all netif are down. Now ethtool will show:
- PTP PHC clock index 0 after boot until first netif is up;
- the last assigned PTP PHC clock index even if PTP PHC clock is not
registered any more after all netifs are down.
This patch ensures that -1 is returned by ethtool when PTP PHC clock is not
registered any more.
Fixes: 8a2c9a5ab4 ("net: ethernet: ti: cpts: rework initialization/deinitialization")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201224162405.28032-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 7f0a838254 ("bpf, xdp: Maintain info on attached XDP BPF
programs in net_device"), the XDP program attachment info is now maintained
in the core code. This interacts badly with the xdp_attachment_flags_ok()
check that prevents unloading an XDP program with different load flags than
it was loaded with. In practice, two kinds of failures are seen:
- An XDP program loaded without specifying a mode (and which then ends up
in driver mode) cannot be unloaded if the program mode is specified on
unload.
- The dev_xdp_uninstall() hook always calls the driver callback with the
mode set to the type of the program but an empty flags argument, which
means the flags_ok() check prevents the program from being removed,
leading to bpf prog reference leaks.
The original reason this check was added was to avoid ambiguity when
multiple programs were loaded. With the way the checks are done in the core
now, this is quite simple to enforce in the core code, so let's add a check
there and get rid of the xdp_attachment_flags_ok() callback entirely.
Fixes: 7f0a838254 ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device")
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/bpf/160752225751.110217.10267659521308669050.stgit@toke.dk
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-12-03
The main changes are:
1) Support BTF in kernel modules, from Andrii.
2) Introduce preferred busy-polling, from Björn.
3) bpf_ima_inode_hash() and bpf_bprm_opts_set() helpers, from KP Singh.
4) Memcg-based memory accounting for bpf objects, from Roman.
5) Allow bpf_{s,g}etsockopt from cgroup bind{4,6} hooks, from Stanislav.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (118 commits)
selftests/bpf: Fix invalid use of strncat in test_sockmap
libbpf: Use memcpy instead of strncpy to please GCC
selftests/bpf: Add fentry/fexit/fmod_ret selftest for kernel module
selftests/bpf: Add tp_btf CO-RE reloc test for modules
libbpf: Support attachment of BPF tracing programs to kernel modules
libbpf: Factor out low-level BPF program loading helper
bpf: Allow to specify kernel module BTFs when attaching BPF programs
bpf: Remove hard-coded btf_vmlinux assumption from BPF verifier
selftests/bpf: Add CO-RE relocs selftest relying on kernel module BTF
selftests/bpf: Add support for marking sub-tests as skipped
selftests/bpf: Add bpf_testmod kernel module for testing
libbpf: Add kernel module BTF support for CO-RE relocations
libbpf: Refactor CO-RE relocs to not assume a single BTF object
libbpf: Add internal helper to load BTF data by FD
bpf: Keep module's btf_data_size intact after load
bpf: Fix bpf_put_raw_tracepoint()'s use of __module_address()
selftests/bpf: Add Userspace tests for TCP_WINDOW_CLAMP
bpf: Adds support for setting window clamp
samples/bpf: Fix spelling mistake "recieving" -> "receiving"
bpf: Fix cold build of test_progs-no_alu32
...
====================
Link: https://lore.kernel.org/r/20201204021936.85653-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add napi_id to the xdp_rxq_info structure, and make sure the XDP
socket pick up the napi_id in the Rx path. The napi_id is used to find
the corresponding NAPI structure for socket busy polling.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/bpf/20201130185205.196029-7-bjorn.topel@gmail.com
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 83a8471ba2 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Link: https://lore.kernel.org/r/1605250173-18438-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We always have to update the value of ret, otherwise the
error value may be the previous one.
Fixes: f6bd59526c ("net: ethernet: ti: introduce am654 common platform time sync driver")
Signed-off-by: Wang Qing <wangqing@vivo.com>
[grygorii.strashko@ti.com: fix build warn, subj add fixes tag]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201112164541.3223-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Depending on the SoC/platform the CPSW can completely lose context after a
suspend/resume cycle, including CPSW wrapper (WR) which will cause reset of
WR_C0_MISC_EN register, so CPTS IRQ will became disabled.
Fix it by moving CPTS IRQ enabling in cpsw_ndo_open() where CPTS is
actually started.
Fixes: 84ea9c0a95 ("net: ethernet: ti: cpsw: enable cpts irq")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20201112111546.20343-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use new dev_err_probe() API to handle deferred probe properly and simplify
the code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds final multi-port support to TI AM65x CPSW driver path in
preparation for adding support for multi-port devices, like Main CPSW0 on
K3 J721E SoC or future CPSW3g on K3 AM64x SoC.
- the separate netdev is created for every enabled external Port;
- DMA channels are common/shared for all external Ports and the RX/TX NAPI
and DMA processing assigned to first available netdev;
- external Ports are configured in mac-only mode, which is similar to TI
"dual-mac" mode for legacy TI CPSW - packets are sent to the Host port only
in ingress and directly to the Port on egress. No packet switching between
external ports happens.
- every port supports the same features as current AM65x CPSW on external
device.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch adds multi-port support to TI AM65x CPSW driver xmit/rx path in
preparation for adding support for multi-port devices, like Main CPSW0 on
K3 J721E SoC or future CPSW3g on K3 AM64x SoC.
Hence DMA channels are common/shared for all ext Ports and the RX/TX NAPI
and DMA processing going to be assigned to first available netdev this patch:
- ensures all RX descriptors fields are initialized;
- adds synchronization for TX DMA push/pop operation (locking) as
Networking core locks are not enough any more;
- updates TX bql processing for every packet in
am65_cpsw_nuss_tx_compl_packets() as every completed TX skb can have
different ndev assigned (come from different netdevs).
To avoid performance issues for existing one-port CPSW2g devices the above
changes are done only for multi-port devices by splitting xmit path for
one-port and multi-port devices.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The current implementation uses .ndo_set_features() callback to track
NETIF_F_HW_CSUM feature changes and update generic
CPSW_P0_CONTROL_REG.RX_CHECKSUM_EN option accordingly. It's not going to
work in case of multi-port devices as TX csum offload can be changed per
netdev.
On K3 CPSWxG devices TX csum offload enabled in the following way:
- the CPSW_P0_CONTROL_REG.RX_CHECKSUM_EN option enables TX csum offload in
generic and affects all TX DMA channels and packets;
- corresponding fields in TX DMA descriptor have to be filed properly when
upper layer wants to offload TX csum (skb->ip_summed == CHECKSUM_PARTIAL)
and it's per-packet option.
The Linux Network core is expected to never request TX csum offload if
netdev NETIF_F_HW_CSUM feature is disabled, and, as result, TX DMA
descriptors should not be modified, and per-packet TX csum offload will be
disabled (or enabled) on per-netdev basis. Which, in turn, makes it safe to
enable the CPSW_P0_CONTROL_REG.RX_CHECKSUM_EN option unconditionally.
Hence, fix TX csum offload for multi-port devices by:
- enabling the CPSW_P0_CONTROL_REG.RX_CHECKSUM_EN option in
am65_cpsw_nuss_common_open() unconditionally
- and removing .ndo_set_features() callback implementation, which was used
only NETIF_F_HW_CSUM feature update purposes
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some K3 CPSW NUSS instances can lose context after PM runtime ON->OFF->ON
transition depending on integration (including all submodules: CPTS, MDIO,
etc), like J721E Main CPSW (CPSW9G).
In case CPTS is enabled it's initialized during probe and does not expect
to be reset. Hence, keep K3 CPSW active by forbidding PM runtime if CPTS is
enabled.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VLAN offload for AM65x CPSW2G is implemented using existing ALE APIs,
which are also used by legacy CPSW drivers.
So, now it always adds current Ext. Port and Host as VLAN members when VLAN
is added by 8021Q core (.ndo_vlan_rx_add_vid) and forcibly removes VLAN
from ALE table in .ndo_vlan_rx_kill_vid(). This works as for AM65x CPSW2G
(which has only one Ext. Port) as for legacy CPSW devices (which can't
support same VLAN on more then one Port in multi mac (dual-mac) mode). But
it doesn't work for the new J721E and AM64x multi port CPSWxG versions
doesn't have such restrictions and allow to offload the same VLAN on any
number of ports.
Now the attempt to add same VLAN on two (or more) K3 CPSWxG Ports will
cause:
- VLAN members mask overwrite when VLAN is added
- VLAN removal from ALE table when any Port removes VLAN
This patch fixes an issue by:
- switching to use cpsw_ale_vlan_add_modify() instead of
cpsw_ale_add_vlan() when VLAN is added to ALE table, so VLAN members
mask will not be overwritten;
- Updates cpsw_ale_del_vlan() as:
if more than one ext. Port is in VLAN member mask
then remove only current port from VLAN member mask
else remove VLAN ALE entry
Example:
add: P1 | P0 (Host) -> members mask: P1 | P0
add: P2 | P0 -> members mask: P2 | P1 | P0
rem: P1 | P0 -> members mask: P2 | P0
rem: P2 | P0 -> members mask: -
The VLAN is forcibly removed if port_mask=0 passed to cpsw_ale_del_vlan()
to preserve existing legacy CPSW drivers functionality.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add/export cpsw_ale_vlan_del_modify() and use it in cpsw_switchdev instead
of generic cpsw_ale_del_vlan() to avoid mixing 8021Q and switchdev VLAN
offload. This is preparation patch equired by follow up changes.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of adding more multi-port K3 CPSW versions move free
descriptor queue mode selection in am65_cpsw_pdata, so it can be selected
basing on DT compatibility property.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation of adding more multi-port K3 CPSW versions move ALE
selection in am65_cpsw_pdata, so it can be selected basing on DT
compatibility property.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TI CPTS does not natively support PTPv1, only PTPv2. But, as it
happens, the CPTS can provide HW timestamp for PTPv1 Sync messages, because
CPTS HW parser looks for PTP messageType id in PTP message octet 0 which
value is 0 for PTPv1. As result, CPTS HW can detect Sync messages for PTPv1
and PTPv2 (Sync messageType = 0 for both), but it fails for any other PTPv1
messages (Delay_req/resp) and will return PTP messageType id 0 for them.
The commit e9523a5a32 ("net: ethernet: ti: cpsw: enable
HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter") added PTPv1 hw timestamping
advertisement by mistake, only to make Linux Kernel "timestamping" utility
work, and this causes issues with only PTPv1 compatible HW/SW - Sync HW
timestamped, but Delay_req/resp are not.
Hence, fix it disabling PTPv1 hw timestamping advertisement, so only PTPv1
compatible HW/SW can properly roll back to SW timestamping.
Fixes: e9523a5a32 ("net: ethernet: ti: cpsw: enable HWTSTAMP_FILTER_PTP_V1_L4_EVENT filter")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Link: https://lore.kernel.org/r/20201029190910.30789-1-grygorii.strashko@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The driver uses in_irq() to determine if the tlan_priv::lock has to be
acquired in tlan_mii_read_reg() and tlan_mii_write_reg().
The interrupt handler acquires the lock outside of these functions so the
in_irq() check is meant to prevent a lock recursion deadlock. But this
check is incorrect when interrupt force threading is enabled because then
the handler runs in thread context and in_irq() correctly returns false.
The usage of in_*() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
seperated or the context be conveyed in an argument passed by the caller,
which usually knows the context.
tlan_set_timer() has this conditional as well, but this function is only
invoked from task context or the timer callback itself. So it always has to
lock and the check can be removed.
tlan_mii_read_reg(), tlan_mii_write_reg() and tlan_phy_print() are invoked
from interrupt and other contexts.
Split out the actual function body into helper variants which are called
from interrupt context and make the original functions wrappers which
acquire tlan_priv::lock unconditionally.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Samuel Chessman <chessman@tux.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.
After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.
The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
| ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
2084 | RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
603 | u32 tbisr, tanar, tanlpar;
| ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
1207 | u32 cfg, tanar, tbicr;
| ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
1063 | int data_size, yf_size;
| ^~~~~~~
Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line
[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.
Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]
The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.
When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.
Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
This addresses the following coccinelle warning:
drivers/net/ethernet/ti/cpsw.c:1599:2-17: WARNING: Assignment of 0/1 to
bool variable
drivers/net/ethernet/ti/cpsw.c:1300:2-17: WARNING: Assignment of 0/1 to
bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed suspend/resume callbacks to properly restore networking after
suspend/resume cycle.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI J721E (CPSW9g) ALE version is similar, in general, to Sitara AM3/4/5
CPSW ALE, but has more extended functions and different ALE VLAN entry
format.
This patch adds support for for multi port TI J721E (CPSW9g) ALE variant.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ALE VLAN entries are too much differ between different TI CPSW ALE
versions. So, handling them using flags, defines and get/set functions
became over-complicated.
This patch introduces tables to describe the ALE VLAN entries fields, which
are different between TI CPSW ALE versions, and new get/set access
functions. It also allows to detect incorrect access to not available ALL
entry fields.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AM65x ALE supports HW auto-ageing which can be enabled by programming
ageing interval in ALE_AGING_TIMER register. For this CPSW fck_clk
frequency has to be know by ALE.
This patch extends cpsw_ale_params with bus_freq field and enables ALE HW
auto ageing for AM65x CPSW2G ALE version.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hence all existing driver updated to use ALE dev_id the usage of ale dev_id
can be made mandatory and cpsw_ale_create() can be updated to use
"features" property from ALE static configuration.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI TI AM65x/J721E CPSW NUSS driver to use
dev_id.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI Keystone 2 NETCP driver to use dev_id and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch has introduced possibility to select CPSW ALE by using
ALE dev_id identifier. Switch TI cpsw driver to use dev_id="cpsw" and
perform clean up by removing "ale_entries" configuration code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As existing, as newly introduced CPSW ALE versions have differences in
supported features and ALE table formats. Especially it's actual for the
recent AM65x/J721E/J7200 SoC and feature AM64x, which supports features
like: auto-aging, classifiers, Link aggregation, additional hw filtering,
etc.
Existing ALE configuration interface is not practical in terms of adding
new features and requires consumers to program a lot static parameters. Any
attempt to add new options will case endless adding and maintaining
different combination of flags and options.
Hence CPSW ALE configuration is static and fixed for SoC (or set of SoC) It
is reasonable to add support for static ALE configurations inside ALE
module. This patch adds static ALE configuration table for different ALE
versions and provides option for consumers to select required ALE
configuration by providing ALE const char *dev_id identifier.
This feature is not enabled by default until existing CPSW drivers will be
modified by follow up patches.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add cpsw_ale_get_num_entries() API to return number of ALE table entries
and update existing drivers to use it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
In RMII link mode it's required to set bit 15 IFCTL_A in MAC_SL MAC_CONTROL
register to enable support for 100Mbit link speed.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new bit TX_GENF_CLR_EN has been added in AM65x SR2.0 to fix i2083
errata, which can be just set unconditionally for all SoCs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bunch of issues in cpsw_ndo_vlan_rx_kill_vid()
- pm_runtime_get_sync() returns non zero value. This results in
non zero value return to caller which will be interpreted as error.
So overwrite ret with zero.
- If VID matches with port VLAN VID, then set error code.
- Currently when VLAN interface is deleted, all of the VLAN mc addresses
are removed from ALE table, however the return values from ale function
calls are not checked. These functions can return error code -ENOENT.
But that shouldn't happen in a normal case. So add error print to
catch the situations so that these can be investigated and addressed.
return zero in these cases as these are not real error case, but only
serve to catch ALE table update related issues and help address the
same in the driver.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To flush the vid + mc entries from ALE, which is required when a VLAN
interface is removed, driver needs to call cpsw_ale_flush_multicast()
with ALE_PORT_HOST for port mask as these entries are added only for
host port. Without this, these entries remain in the ALE table even
after removing the VLAN interface. cpsw_ale_flush_multicast() calls
cpsw_ale_flush_mcast which expects a port mask to do the job.
Fixes: 15180eca56 ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to reduce code duplication between ptp drivers, generic helper
functions were introduced. Use them.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers using legacy power management .suspen()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a single
"struct dev_pm_ops" variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently drive supports taprio offload which is a tc feature offloaded
to cpsw hardware. So driver has to set the hw feature flag, NETIF_F_HW_TC
in the net device to be compliant. This patch adds the flag.
Fixes: 8127224c27 ("ethernet: ti: am65-cpsw-qos: add TAPRIO offload support")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AM65x SR2.0 MCU CPSW has fixed errata i2027 "CPSW: CPSW Does Not
Support CPPI Receive Checksum (Host to Ethernet) Offload Feature". This
errata also fixed for J271E SoC.
Use SOC bus data for K3 SoC identification and apply i2027 errata w/a only
for the AM65x SR1.0 SoC.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that critical setting can only be configured when there are no
running netdevs - all ports are down.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Skip HW configuration when p0-rx-ptype-rrobin is changed as it will be done
by .ndev_open(),
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC SL has to be initialized for each port otherwise
am65_cpsw_nuss_slave_disable_unused() will crash for disabled ports.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pf_p0_rx_ptype_rrobin is global parameter so move its initialization in
probe.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan configuration is not restored after interface down/up sequence.
Steps to check:
# ip link add link eth0 name eth0.100 type vlan id 100
# ifconfig eth0 down
# ifconfig eth0 up
This patch fixes it, restoring vlan ALE entries on .ndo_open().
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Organize driver documentation by device type. Most documents
have fairly verbose yet uninformative names, so let users
first select a well defined device type, and then search for
a particular driver.
While at it rename the section from Vendor drivers to
Hardware drivers. This seems more accurate, besides people
sometimes refer to out-of-tree drivers as vendor drivers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes. Also, remove unnecessary
variable _size_.
This code was detected with the help of Coccinelle and, audited and
fixed manually.
Addresses-KSPP-ID: https://github.com/KSPP/linux/issues/83
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix cfg80211 deadlock, from Johannes Berg.
2) RXRPC fails to send norigications, from David Howells.
3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
Geliang Tang.
4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.
5) The ucc_geth driver needs __netdev_watchdog_up exported, from
Valentin Longchamp.
6) Fix hashtable memory leak in dccp, from Wang Hai.
7) Fix how nexthops are marked as FDB nexthops, from David Ahern.
8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.
9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.
10) Fix link speed reporting in iavf driver, from Brett Creeley.
11) When a channel is used for XSK and then reused again later for XSK,
we forget to clear out the relevant data structures in mlx5 which
causes all kinds of problems. Fix from Maxim Mikityanskiy.
12) Fix memory leak in genetlink, from Cong Wang.
13) Disallow sockmap attachments to UDP sockets, it simply won't work.
From Lorenz Bauer.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
net: ethernet: ti: ale: fix allmulti for nu type ale
net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
net: atm: Remove the error message according to the atomic context
bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
libbpf: Support pre-initializing .bss global variables
tools/bpftool: Fix skeleton codegen
bpf: Fix memlock accounting for sock_hash
bpf: sockmap: Don't attach programs to UDP sockets
bpf: tcp: Recv() should return 0 when the peer socket is closed
ibmvnic: Flush existing work items before device removal
genetlink: clean up family attributes allocations
net: ipa: header pad field only valid for AP->modem endpoint
net: ipa: program upper nibbles of sequencer type
net: ipa: fix modem LAN RX endpoint id
net: ipa: program metadata mask differently
ionic: add pcie_print_link_status
rxrpc: Fix race between incoming ACK parser and retransmitter
net/mlx5: E-Switch, Fix some error pointer dereferences
net/mlx5: Don't fail driver on failure to create debugfs
net/mlx5e: CT: Fix ipv6 nat header rewrite actions
...
On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.
This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f644727 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").
Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().
Fixes: 9d1f644727 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
In order to use standard 'xdp' prefix, rename convert_to_xdp_frame
utility routine in xdp_convert_buff_to_frame and replace all the
occurrences
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Link: https://lore.kernel.org/bpf/6344f739be0d1a08ab2b9607584c4d5478c8c083.1590698295.git.lorenzo@kernel.org
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
cpsw_suspend()
|- cpsw_ndo_stop()
|- __hw_addr_ref_unsync_dev()
|- cpsw_purge_all_mc()
|- vlan_for_each()
|- ASSERT_RTNL();
Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.
Fixes: 15180eca56 ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert to using IS_ERR() instead of NULL test for cpsw_ale_create()
error handling. Also fix to return negative error code from this error
handling case instead of 0 in.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpsw_ale_create() can return both NULL and PTR_ERR(), but all of
the caller only check NULL for error handling. This patch convert
it to only return PTR_ERR() in all error cases, and the caller using
IS_ERR() instead of NULL test.
Fixes: 4b41d34367 ("net: ethernet: ti: cpsw: allow untagged traffic on host port")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with Clang:
In file included from drivers/net/ethernet/ti/am65-cpsw-ethtool.c:15:
drivers/net/ethernet/ti/am65-cpts.h:58:12: warning: unused function
'am65_cpts_ns_gettime' [-Wunused-function]
static s64 am65_cpts_ns_gettime(struct am65_cpts *cpts)
^
drivers/net/ethernet/ti/am65-cpts.h:63:12: warning: unused function
'am65_cpts_estf_enable' [-Wunused-function]
static int am65_cpts_estf_enable(struct am65_cpts *cpts,
^
drivers/net/ethernet/ti/am65-cpts.h:69:13: warning: unused function
'am65_cpts_estf_disable' [-Wunused-function]
static void am65_cpts_estf_disable(struct am65_cpts *cpts, int idx)
^
3 warnings generated.
These functions need to be marked as inline, which adds __maybe_unused,
to avoid these warnings, which is the pattern for stub functions.
Fixes: ec008fa2a9 ("ethernet: ti: am65-cpts: add routines to support taprio offload")
Link: https://github.com/ClangBuiltLinux/linux/issues/1026
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bpf verifier trace check into the new switch statement in
HEAD.
Resolve the overlapping changes in hinic, where bug fixes overlap
the addition of VF support.
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver code cpsw.c and cpsw_new.c both use page_pool
with default order-0 pages or their RX-pages.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/bpf/158945340875.97035.752144756428532878.stgit@firesoul
AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() to offload EST configuration to CPSW h/w.
Currently driver supports only SetGateStates operation. EST
operates on a repeating time interval generated by the CPTS EST
function generator. Each Ethernet port has a global EST fetch
RAM that can be configured as 2 buffers, each of 64 locations
or one large buffer of 128 locations. In 2 buffer configuration,
a ping pong mechanism is used to hold the active schedule (oper)
in one buffer and new (admin) command in the other. Each 22-bit
fetch command consists of a 14-bit fetch count (14 MSB’s) and an
8-bit priority fetch allow (8 LSB’s) that will be applied for the
fetch count time in wireside clocks. Driver process each of the
sched-entry in the offload command and update the fetch RAM.
Driver configures duration in sched-entry into the fetch count
and Gate mask into the priority fetch bits of the RAM. Then
configures the CPTS EST function generator to activate the
schedule. Currently driver supports only 2 buffer configuration
which means driver supports a max cycle time of ~8 msec.
CPSW supports a configurable number of priority queues (up to 8)
and needs to be switched to this mode from the default round
robin mode before EST can be offloaded. User configures
these through ethtool commands (-L for changing number of
queues and --set-priv-flags to disable round robin mode).
Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag
is set. The flag is common for all ports, and so can't be just
overridden by taprio configuration w/o user involvement.
Command fails if pf_p0_rx_ptype_rrobin is already set in the
driver.
Scheds (commands) configuration depends on interface speed so
driver translates the duration to the fetch count based on
link speed. Each schedule can be constructed with several
command entries in fetch RAM depending on interval. For example
if each sched has timer interval < ~130us on 1000 Mb link then
each sched consumes one command and have 1:1 mapping. When
Ethernet link goes down, driver purge the configuration if link
is down for more than 1 second.
The patch allows to update the timer and scheds memory only if it's
really needed, and skip cases required the user to stop timer by
configuring only shceds memory.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TAPRIO/EST offload support in CPSW2G requires EST scheduler
function enabled in CPTS. So this patch add a function to
set cycle time for EST scheduler. It also add a function for
getting time in ns of PHC clock for taprio qdisc configuration.
Mostly to verify if timer update is needed or to get actual
state of oper/admin schedule.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My recent commit b6d49cab44 ("net: Make PTP-specific drivers depend on
PTP_1588_CLOCK") exposes a missing dependency in defconfigs that select
TI_CPTS without selecting PTP_1588_CLOCK, leading to linker errors of the
form:
drivers/net/ethernet/ti/cpsw.o: in function `cpsw_ndo_stop':
cpsw.c:(.text+0x680): undefined reference to `cpts_unregister'
...
That's because TI_CPTS_MOD (which is the symbol gating the _compilation_ of
cpts.c) now depends on PTP_1588_CLOCK, and so is not enabled in these
configurations, but TI_CPTS (which is the symbol gating _calls_ to the cpts
functions) _is_ enabled. So we end up compiling calls to functions that
don't exist, resulting in the linker errors.
This patch fixes build errors and restores previous behavior by:
- ensure PTP_1588_CLOCK=y in TI specific configs and CPTS will be built
- remove TI_CPTS_MOD and, instead, add dependencies from CPTS in
TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV as below:
config TI_CPSW_SWITCHDEV
...
depends on TI_CPTS || !TI_CPTS
which will ensure proper dependencies PTP_1588_CLOCK -> TI_CPTS ->
TI_CPSW/TI_KEYSTONE_NETCP/TI_CPSW_SWITCHDEV and build type selection.
Note. For NFS boot + CPTS all of above configs have to be built-in.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Fixes: b6d49cab44 ("net: Make PTP-specific drivers depend on PTP_1588_CLOCK")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Clay McClure <clay@daemons.net>
[grygorii.strashko@ti.com: rewording, add deps cpsw/netcp from cpts, drop IS_REACHABLE]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCU CPSW expected to populate only MDIO device, but follow up patches
will add "compatible" property to the MCU CPSW CPTS node which will cause
creation of CPTS device and MCU CPSW init failure. Hence, switch to use
of_platform_device_create() instead of of_platform_populate() for MDIO
device population.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The K3 INTA driver, which is source TX/RX IRQs for CPSW NUSS, defines IRQs
triggering type as EDGE by default, but triggering type for CPSW NUSS TX/RX
IRQs has to be LEVEL as the EDGE triggering type may cause unnecessary IRQs
triggering and NAPI scheduling for empty queues. It was discovered with
RT-kernel.
Fix it by explicitly specifying CPSW NUSS TX/RX IRQ type as
IRQF_TRIGGER_HIGH.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix
the ndo function to use the correct type.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes coccicheck warning:
drivers/net/ethernet/ti/am65-cpts.c:1017:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Samuel Zou <zou_wei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible to have build configuration which will force PTP_1588_CLOCK=m
and so TI_K3_AM65_CPTS=m while still have TI_K3_AM65_CPSW_NUSS=y. This will
cause build failures:
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.o: in function `am65_cpsw_init_cpts':
../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685: undefined reference to `am65_cpts_create'
aarch64-linux-gnu-ld: ../drivers/net/ethernet/ti/am65-cpsw-nuss.c:1685:(.text+0x2e20):
relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `am65_cpts_create'
Fix it by adding dependencies from CPTS in TI_K3_AM65_CPSW_NUSS as below:
config TI_K3_AM65_CPSW_NUSS
...
depends on TI_K3_AM65_CPTS || !TI_K3_AM65_CPTS
Note. This will create below dependencies and for NFS boot + CPTS all of them
have to be built-in.
PTP_1588_CLOCK -> TI_K3_AM65_CPTS -> TI_K3_AM65_CPSW_NUSS
While here, clean up TI_K3_AM65_CPTS definition.
Fixes: b1f66a5bee ("net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
drivers/net/ethernet/ti/cpsw_new.c:1924:2-17: WARNING: Assignment of
0/1 to bool variable
drivers/net/ethernet/ti/cpsw_new.c:1231:1-16: WARNING: Assignment of
0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.
This enables corresponding support in TI AM65x/J721E MCU CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPTS module is used to facilitate host control of time sync operations.
Main features of CPTS module are:
- selection of multiple external clock sources
- control of time sync events via interrupt or polling
- 64-bit timestamp mode in ns with HW PPM and nudge adjustment.
- hardware timestamp ext. inputs (HWx_TS_PUSH)
- timestamp Generator function outputs (TS_GENFx)
Depending on integration it enables compliance with the IEEE 1588-2008
standard for a precision clock synchronization protocol, Ethernet Enhanced
Scheduled Traffic Operations (CPTS_ESTFn) and PCIe Subsystem Precision Time
Measurement (PTM).
Introduced driver provides Linux PTP hardware clock for each CPTS device
and network packets timestamping where applicable. CPTS PTP hardware clock
supports following operations:
- Set time
- Get time
- Shift the clock by a given offset atomically
- Adjust clock frequency
- Time stamp external events
- Periodic output signals
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d1cbfd771c ("ptp_clock: Allow for it to be optional") changed
all PTP-capable Ethernet drivers from `select PTP_1588_CLOCK` to `imply
PTP_1588_CLOCK`, "in order to break the hard dependency between the PTP
clock subsystem and ethernet drivers capable of being clock providers."
As a result it is possible to build PTP-capable Ethernet drivers without
the PTP subsystem by deselecting PTP_1588_CLOCK. Drivers are required to
handle the missing dependency gracefully.
Some PTP-capable Ethernet drivers (e.g., TI_CPSW) factor their PTP code
out into separate drivers (e.g., TI_CPTS_MOD). The above commit also
changed these PTP-specific drivers to `imply PTP_1588_CLOCK`, making it
possible to build them without the PTP subsystem. But as Grygorii
Strashko noted in [1]:
On Wed, Apr 22, 2020 at 02:16:11PM +0300, Grygorii Strashko wrote:
> Another question is that CPTS completely nonfunctional in this case and
> it was never expected that somebody will even try to use/run such
> configuration (except for random build purposes).
In my view, enabling a PTP-specific driver without the PTP subsystem is
a configuration error made possible by the above commit. Kconfig should
not allow users to create a configuration with missing dependencies that
results in "completely nonfunctional" drivers.
I audited all network drivers that call ptp_clock_register() but merely
`imply PTP_1588_CLOCK` and found five PTP-specific drivers that are
likely nonfunctional without PTP_1588_CLOCK:
NET_DSA_MV88E6XXX_PTP
NET_DSA_SJA1105_PTP
MACB_USE_HWSTAMP
CAVIUM_PTP
TI_CPTS_MOD
Note how these symbols all reference PTP or timestamping in their name;
this is a clue that they depend on PTP_1588_CLOCK.
Change them from `imply PTP_1588_CLOCK` [2] to `depends on PTP_1588_CLOCK`.
I'm not using `select PTP_1588_CLOCK` here because PTP_1588_CLOCK has
its own dependencies, which `select` would not transitively apply.
Additionally, remove the `select NET_PTP_CLASSIFY` from CPTS_TI_MOD;
PTP_1588_CLOCK already selects that.
[1]: https://lore.kernel.org/lkml/c04458ed-29ee-1797-3a11-7f3f560553e6@ti.com/
[2]: NET_DSA_SJA1105_PTP had never declared any type of dependency on
PTP_1588_CLOCK (`imply` or otherwise); adding a `depends on PTP_1588_CLOCK`
here seems appropriate.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: d1cbfd771c ("ptp_clock: Allow for it to be optional")
Signed-off-by: Clay McClure <clay@daemons.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
since devm_ioremap() does not check input parameters for null.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = \(platform_get_resource\|platform_get_resource_byname\)(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Fixes: 03f66f0675 ("net: ethernet: ti: davinci_mdio: use devm_ioremap()")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- add SPDX header;
- adjust titles and chapters, adding proper markups;
- mark tables as such;
- mark code blocks and literals as such;
- adjust identation, whitespaces and blank lines where needed;
- add to networking/index.rst.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function gen_pool_create() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW misc IRQ need be enabled for CPTS event_pend IRQs processing. This
patch adds corresponding support to CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hence CPTS IRQ support is in place the W_TS_PUSH events can be added.
PWM capable DmTimers can be used to generete input signals for CPTS on TI
AM335x/AM437x/DRA7 SoCs to be timestamped:
AM335x/AM437x: timer4 - timer7
DRA7/AM57xx: timer13 - timer16
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CPTS IRQ support, but do not enable it. By default, the CPTS driver
will continue working using polling mode which is required for CPTS to
continue working on platforms other than CPSW, like Keystone 2.
The CPTS IRQ support is required to enable support for HW_TS_PUSH events.
The CPSW CPTS IRQ and HW_TS_PUSH events support will be enabled in follow
up patches.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now spinlock is used to synchronize everything which is not required. Add
mutex and use to sync access to PTP interface and PTP worker and use
spinlock only to sync FIFO/events processing.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the tx timestamp processing happens from different contexts - softirq
and thread/PTP worker. Enabling IRQ will add one more hard_irq context.
This makes over all defered TX timestamp processing and locking
overcomplicated. Move tx timestamp processing to PTP worker always instead.
napi_rx->cpts_tx_timestamp
if ptp_packet then
push to txq
ptp_schedule_worker()
do_aux_work->cpts_overflow_check
cpts_process_events()
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the CPTS driver performs packet (skb) parsing every time when it needs
to match packet to CPTS event (including ptp_classify_raw() calls).
This patch optimizes matching process by parsing packet only once upon
arrival and stores PTP specific data in skb->cb using the same fromat as in
CPTS HW event. As result, all future matching reduces to comparing two u32
values.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPTS HW latches and saves CPTS counter value in CPTS fifo immediately
after writing to CPSW_CPTS_PUSH.TS_PUSH (bit 0), so the total time that the
driver needs to read the CPTS timestamp is the time required CPSW_CPTS_PUSH
write to actually reach HW.
Hence switch CPTS driver to implement new .gettimex64() callback for more
precise measurement of the offset between a PHC and the system clock which
is measured as time between
write(CPSW_CPTS_PUSH)
read(CPSW_CPTS_PUSH)
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPTS driver .adjfreq() generates request to read CPTS current time
(CPTS_EV_PUSH) with intention to process all pending event using previous
frequency adjustment values before switching to the new ones. So
CPTS_EV_PUSH works as a marker to switch to the new frequency adjustment
values. Current code assumes that all job is done in .adjfreq(), but after
enabling IRQ this will not be true any more.
Hence save new frequency adjustment values (mult) and perform actual freq
adjustment in cpts_fifo_read() immediately after CPTS_EV_PUSH is received.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now CPTS HW time reading code is implemented in timecounter->cyclecounter
.read() callback and performs following operations:
timecounter_read() ->cc.read() -> cpts_systim_read()
- request current CPTS HW time CPTS_TS_PUSH.TS_PUSH = 1
- poll CPTS FIFO for CPTS_EV_PUSH event with current HW timestamp
This approach need to be changed for the future switch to PTP PHC
.gettimex64() callback, which require to separate requesting current CPTS
HW time and processing CPTS FIFO. And for the follow up patch, which
improves .adjfreq() implementation.
This patch moves code accessing CPTS HW out of timecounter code as
following:
- convert HW timestamp of every CPTS event to PTP time (us) and store it as
part struct cpts_event;
- add CPTS context field to store current CPTS HW time (counter) value and
update it on CPTS_EV_PUSH reception;
- move code accessing CPTS HW out of timecounter code and use current CPTS
HW time (counter) from CPTS context instead;
- ensure timecounter->cycle_last is updated on CPTS_EV_PUSH reception.
After this change CPTS timecounter will only perform timekeeper role
without actually accessing CPTS HW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dev_yy() API instead of pr_yy() for log outputs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.
Fixes: 93a7653031 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a spelling mistake in a dev_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectable RGMII and RMII
interfaces and an internal Communications Port Programming Interface (CPPI)
port (Host port 0) and with ALE in between. It also contains
- Management Data Input/Output (MDIO) interface for physical layer device
(PHY) management;
- Updated Address Lookup Engine (ALE) module;
- (TBD) New version of Common platform time sync (CPTS) module.
On the TI am65x/J721E SoCs CPSW NUSS Ethernet subsystem into device MCU
domain named MCU_CPSW0.
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and one RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.
Introduced driver provides standard Linux net_device to user space and supports:
- ifconfig up/down
- MAC address configuration
- ethtool operation:
--driver
--change
--register-dump
--negotiate phy
--statistics
--set-eee phy
--show-ring
--show-channels
--set-channels
- net_device ioctl mii-control
- promisc mode
- rx checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets.
The CPSW NUSS can verify IPv4/IPv6 TCP/UDP packets checksum and fills
csum information for each packet in psdata[2] word:
- BIT(16) CHECKSUM_ERROR - indicates csum error
- BIT(17) FRAGMENT - indicates fragmented packet
- BIT(18) TCP_UDP_N - Indicates TCP packet was detected
- BIT(19) IPV6_VALID, BIT(20) IPV4_VALID - indicates IPv6/IPv4 packet
- BIT(15, 0) CHECKSUM_ADD - This is the value that was summed
during the checksum computation. This value is FFFFh for non fragmented
IPV4/6 UDP/TCP packets with no checksum error.
RX csum offload can be disabled:
ethtool -K <dev> rx-checksum on|off
- tx checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).
TX csum HW offload can be enabled/disabled:
ethtool -K <dev> tx-checksum-ip-generic on|off
- multiq and switch between round robin/prio modes for cppi tx queues by
using Netdev private flag "p0-rx-ptype-rrobin" to switch between
Round Robin and Fixed priority modes:
# ethtool --show-priv-flags eth0
Private flags for eth0:
p0-rx-ptype-rrobin: on
# ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off
Number of TX DMA channels can be changed using "ethtool -L eth0 tx <N>".
- GRO support: the napi_gro_receive() and napi_complete_done() are used.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for default thread configuration for AM65x CPSW NUSS ALE to
allow route all ingress packets to one default RX UDMA flow.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new CPSW ALE version, available on TI K3 AM654/J721E SoCs family,
allows to switch any external port to MAC only mode. When MAC only mode
enabled this port be treated like a MAC port for the host. All traffic
received is only sent to the host. The host must direct traffic to this
port as the lookup engine will not send traffic to the ports with the
p0_maconly bit set and the p0_no_learn also set. If p0_maconly bit is set
and the p0_no_learn is not set, the host can send non-directed packets that
can be sent to the destination of a MacOnly port. It is also possible that
The host can broadcast to all ports including MacOnly ports in this mode.
This patch add ALE supprt for MAC only mode.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS the unregistered multicast
packets are still can be received with promisc and allmulti disabled.
This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
ALE VLAN entry:UNREG_MCAST_FLOOD_INDEX -> ALE_VLAN_MASK_MUXx
ALE VLAN entry:REG_MCAST_FLOOD_INDEX -> ALE_VLAN_MASK_MUXy
The commit b361da8373 ("net: netcp: ale: add proper ale entry mask bits
for netcp switch ALE") update ALE code to support such ALE entries, it is
always used ALE_VLAN_MASK_MUX0_REG index in ALE VLAN entry for unreg mcast
packets mask configuration, which is read-only, at least for AM65xx MCU
CPSW2G NUSS and 66AK2E/L NUSS. As result unreg mcast packets are allowed
always.
Hence, update ALE code to use ALE_VLAN_MASK_MUX1_REG index for ALE VLAN
entries to configure unreg mcast port mask.
Fixes: b361da8373 ("net: netcp: ale: add proper ale entry mask bits for netcp switch ALE")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy-gmii-sel can be only auto selected in Kconfig and now the pretty
complex Kconfig dependencies are defined for phy-gmii-sel driver, which
also need to be updated every time phy-gmii-sel is re-used for any new
networking driver.
Simplify Kconfig definition for phy-gmii-sel PHY driver - drop all
dependencies and from networking drivers and rely on using 'imply
PHY_TI_GMII_SEL' in Kconfig definitions for networking drivers instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Convert suitable drivers to use new helper phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The netcp_ethss driver tests fields of the phy_device in order to
determine whether to defer to the PHY's time stamping functionality.
This patch replaces the open coded logic with an invocation of the
proper methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Several nf_flow_table_offload fixes from Pablo Neira Ayuso,
including adding a missing ipv6 match description.
2) Several heap overflow fixes in mwifiex from qize wang and Ganapathi
Bhat.
3) Fix uninit value in bond_neigh_init(), from Eric Dumazet.
4) Fix non-ACPI probing of nxp-nci, from Stephan Gerhold.
5) Fix use after free in tipc_disc_rcv(), from Tuong Lien.
6) Enforce limit of 33 tail calls in mips and riscv JIT, from Paul
Chaignon.
7) Multicast MAC limit test is off by one in qede, from Manish Chopra.
8) Fix established socket lookup race when socket goes from
TCP_ESTABLISHED to TCP_LISTEN, because there lacks an intervening
RCU grace period. From Eric Dumazet.
9) Don't send empty SKBs from tcp_write_xmit(), also from Eric Dumazet.
10) Fix active backup transition after link failure in bonding, from
Mahesh Bandewar.
11) Avoid zero sized hash table in gtp driver, from Taehee Yoo.
12) Fix wrong interface passed to ->mac_link_up(), from Russell King.
13) Fix DSA egress flooding settings in b53, from Florian Fainelli.
14) Memory leak in gmac_setup_txqs(), from Navid Emamdoost.
15) Fix double free in dpaa2-ptp code, from Ioana Ciornei.
16) Reject invalid MTU values in stmmac, from Jose Abreu.
17) Fix refcount leak in error path of u32 classifier, from Davide
Caratti.
18) Fix regression causing iwlwifi firmware crashes on boot, from Anders
Kaseorg.
19) Fix inverted return value logic in llc2 code, from Chan Shu Tak.
20) Disable hardware GRO when XDP is attached to qede, frm Manish
Chopra.
21) Since we encode state in the low pointer bits, dst metrics must be
at least 4 byte aligned, which is not necessarily true on m68k. Add
annotations to fix this, from Geert Uytterhoeven.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (160 commits)
sfc: Include XDP packet headroom in buffer step size.
sfc: fix channel allocation with brute force
net: dst: Force 4-byte alignment of dst_metrics
selftests: pmtu: fix init mtu value in description
hv_netvsc: Fix unwanted rx_table reset
net: phy: ensure that phy IDs are correctly typed
mod_devicetable: fix PHY module format
qede: Disable hardware gro when xdp prog is installed
net: ena: fix issues in setting interrupt moderation params in ethtool
net: ena: fix default tx interrupt moderation interval
net/smc: unregister ib devices in reboot_event
net: stmmac: platform: Fix MDIO init for platforms without PHY
llc2: Fix return statement of llc_stat_ev_rx_null_dsap_xid_c (and _test_c)
net: hisilicon: Fix a BUG trigered by wrong bytes_compl
net: dsa: ksz: use common define for tag len
s390/qeth: don't return -ENOTSUPP to userspace
s390/qeth: fix promiscuous mode after reset
s390/qeth: handle error due to unsupported transport mode
cxgb4: fix refcount init for TC-MQPRIO offload
tc-testing: initial tdc selftests for cls_u32
...
Without the common part of the driver, the new file fails to link:
drivers/net/ethernet/ti/cpsw_new.o: In function `cpsw_probe':
cpsw_new.c:(.text+0x312c): undefined reference to `ti_cm_get_macid'
Use the same Makefile hack as before, and build cpsw-common.o for
any driver that needs it.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The new driver misses a dependency:
drivers/net/ethernet/ti/cpsw_new.o: In function `cpsw_rx_handler':
cpsw_new.c:(.text+0x259c): undefined reference to `__page_pool_put_page'
cpsw_new.c:(.text+0x25d0): undefined reference to `page_pool_alloc_pages'
drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_fill_rx_channels':
cpsw_priv.c:(.text+0x22d8): undefined reference to `page_pool_alloc_pages'
cpsw_priv.c:(.text+0x2420): undefined reference to `__page_pool_put_page'
drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_create_xdp_rxqs':
cpsw_priv.c:(.text+0x2624): undefined reference to `page_pool_create'
drivers/net/ethernet/ti/cpsw_priv.o: In function `cpsw_run_xdp':
cpsw_priv.c:(.text+0x2dc8): undefined reference to `__page_pool_put_page'
Other drivers use 'select' for PAGE_POOL, so do the same here.
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
The TI CPSW(s) driver produces warning with DMA API debug options enabled:
WARNING: CPU: 0 PID: 1033 at kernel/dma/debug.c:1025 check_unmap+0x4a8/0x968
DMA-API: cpsw 48484000.ethernet: device driver frees DMA memory with different size
[device address=0x00000000abc6aa02] [map size=64 bytes] [unmap size=42 bytes]
CPU: 0 PID: 1033 Comm: ping Not tainted 5.3.0-dirty #41
Hardware name: Generic DRA72X (Flattened Device Tree)
[<c0112c60>] (unwind_backtrace) from [<c010d270>] (show_stack+0x10/0x14)
[<c010d270>] (show_stack) from [<c09bc564>] (dump_stack+0xd8/0x110)
[<c09bc564>] (dump_stack) from [<c013b93c>] (__warn+0xe0/0x10c)
[<c013b93c>] (__warn) from [<c013b9ac>] (warn_slowpath_fmt+0x44/0x6c)
[<c013b9ac>] (warn_slowpath_fmt) from [<c01e0368>] (check_unmap+0x4a8/0x968)
[<c01e0368>] (check_unmap) from [<c01e08a8>] (debug_dma_unmap_page+0x80/0x90)
[<c01e08a8>] (debug_dma_unmap_page) from [<c0752414>] (__cpdma_chan_free+0x114/0x16c)
[<c0752414>] (__cpdma_chan_free) from [<c07525c4>] (__cpdma_chan_process+0x158/0x17c)
[<c07525c4>] (__cpdma_chan_process) from [<c0753690>] (cpdma_chan_process+0x3c/0x5c)
[<c0753690>] (cpdma_chan_process) from [<c0758660>] (cpsw_tx_mq_poll+0x48/0x94)
[<c0758660>] (cpsw_tx_mq_poll) from [<c0803018>] (net_rx_action+0x108/0x4e4)
[<c0803018>] (net_rx_action) from [<c010230c>] (__do_softirq+0xec/0x598)
[<c010230c>] (__do_softirq) from [<c0143914>] (do_softirq.part.4+0x68/0x74)
[<c0143914>] (do_softirq.part.4) from [<c0143a44>] (__local_bh_enable_ip+0x124/0x17c)
[<c0143a44>] (__local_bh_enable_ip) from [<c0871590>] (ip_finish_output2+0x294/0xb7c)
[<c0871590>] (ip_finish_output2) from [<c0875440>] (ip_output+0x210/0x364)
[<c0875440>] (ip_output) from [<c0875e2c>] (ip_send_skb+0x1c/0xf8)
[<c0875e2c>] (ip_send_skb) from [<c08a7fd4>] (raw_sendmsg+0x9a8/0xc74)
[<c08a7fd4>] (raw_sendmsg) from [<c07d6b90>] (sock_sendmsg+0x14/0x24)
[<c07d6b90>] (sock_sendmsg) from [<c07d8260>] (__sys_sendto+0xbc/0x100)
[<c07d8260>] (__sys_sendto) from [<c01011ac>] (__sys_trace_return+0x0/0x14)
Exception stack(0xea9a7fa8 to 0xea9a7ff0)
...
The reason is that cpdma_chan_submit_si() now stores original buffer length
(sw_len) in CPDMA descriptor instead of adjusted buffer length (hw_len)
used to map the buffer.
Hence, fix an issue by passing correct buffer length in CPDMA descriptor.
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: 6670acacd5 ("net: ethernet: ti: davinci_cpdma: add dma mapped submit")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all the occurrences of FIELD_SIZEOF() with sizeof_field() except
at places where these are defined. Later patches will remove the unused
definition of FIELD_SIZEOF().
This patch is generated using following script:
EXCLUDE_FILES="include/linux/stddef.h|include/linux/kernel.h"
git grep -l -e "\bFIELD_SIZEOF\b" | while read file;
do
if [[ "$file" =~ $EXCLUDE_FILES ]]; then
continue
fi
sed -i -e 's/\bFIELD_SIZEOF\b/sizeof_field/g' $file;
done
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Link: https://lore.kernel.org/r/20190924105839.110713-3-pankaj.laxminarayan.bharadiya@intel.com
Co-developed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David Miller <davem@davemloft.net> # for net
Now RX interrupt is triggered twice every time, because in
cpsw_rx_interrupt() it is asked first and then disabled. So there will be
pending interrupt always, when RX interrupt is enabled again in NAPI
handler.
Fix it by first disabling IRQ and then do ask.
Fixes: 870915feab ("drivers: net: cpsw: remove disable_irq/enable_irq as irq can be masked from cpsw itself")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "select NET_SWITCHDEV" vs "depends on NET_SWITCHDEV" to fix Kconfig
warning with CONFIG_COMPILE_TEST=y
WARNING: unmet direct dependencies detected for NET_SWITCHDEV
Depends on [n]: NET [=y] && INET [=n]
Selected by [y]:
- TI_CPSW_SWITCHDEV [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_TI [=y] && (ARCH_DAVINCI || ARCH_OMAP2PLUS || COMPILE_TEST [=y])
because TI_CPSW_SWITCHDEV blindly selects NET_SWITCHDEV even though
INET is not set/enabled, while NET_SWITCHDEV depends on INET.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: ed3525eda4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
The recently updated ALE APIs cpsw_ale_del_mcast() and
cpsw_ale_del_vlan_modify() have an issue and will not delete ALE entry even
if VLAN/mcast group has no more members. Hence fix it here and delete ALE
entry if !port_mask.
The issue affected only new cpsw switchdev driver.
Fixes: e85c143707 ("net: ethernet: ti: ale: modify vlan/mdb api for switchdev")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW switchdev based driver which is operating in dual-emac mode by
default, thus working as 2 individual network interfaces. The Switch mode
can be enabled by configuring devlink driver parameter "switch_mode" to 1:
devlink dev param set platform/48484000.switch \
name switch_mode value 1 cmode runtime
This can be done regardless of the state of Port's netdevs - UP/DOWN, but
Port's netdev devices have to be UP before joining the bridge to avoid
overwriting of bridge configuration as CPSW switch driver completely
reloads its configuration when first Port changes its state to UP.
When the both interfaces joined the bridge - CPSW switch driver will start
marking packets with offload_fwd_mark flag unless "ale_bypass=0".
All configuration is implemented via switchdev API and notifiers.
Supported:
- SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS
- SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS: BR_MCAST_FLOOD
- SWITCHDEV_ATTR_ID_PORT_STP_STATE
- SWITCHDEV_OBJ_ID_PORT_VLAN
- SWITCHDEV_OBJ_ID_PORT_MDB
- SWITCHDEV_OBJ_ID_HOST_MDB
Hence CPSW switchdev driver supports:
- FDB offloading
- MDB offloading
- VLAN filtering and offloading
- STP
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part 1:
Introduce basic CPSW dual_mac driver (cpsw_new.c) which is operating in
dual-emac mode by default, thus working as 2 individual network interfaces.
Main differences from legacy CPSW driver are:
- optimized promiscuous mode: The P0_UNI_FLOOD (both ports) is enabled in
addition to ALLMULTI (current port) instead of ALE_BYPASS. So, Ports in
promiscuous mode will keep possibility of mcast and vlan filtering, which
is provides significant benefits when ports are joined to the same bridge,
but without enabling "switch" mode, or to different bridges.
- learning disabled on ports as it make not too much sense for
segregated ports - no forwarding in HW.
- enabled basic support for devlink.
devlink dev show
platform/48484000.switch
devlink dev param show
platform/48484000.switch:
name ale_bypass type driver-specific
values:
cmode runtime value false
- "ale_bypass" devlink driver parameter allows to enable
ALE_CONTROL(4).BYPASS mode for debug purposes.
- updated DT bindings.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to add support for a switchdev based cpsw driver,
move common functions to cpsw-priv.c so that they can be used across both
drivers.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patches introduce new CPSW switchdev driver which uses common
code with legacy CPSW driver. This will introduce build dependency between
CPSW switchdev and CPSW legacy drivers related to for_each_slave() and
cpsw_slave_index() - they can be compiled both, but only one of them will
be not functional depending in Kconfig settings due to duffrences in Slave
Ports indexes calculation.
To fix this make for_each_slave() local (it's used now only by legacy CPSW
driver) and convert cpsw_slave_index() to be a function pointer which is
assigned in probe. Driver to probe is defined by DT.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A following patch introduces switchdev functionality, so modify
ALE engine VLANs/MDBs API:
- cpsw_ale_del_mcast(): update so it will remove only selected ports from
mcast port_mask or delete whole mcast record if !port_mask
- cpsw_ale_del_vlan(): update so it will remove only selected ports from
all VLAN record's masks or delete whole VLAN record if !port_mask
- add cpsw_ale_vlan_add_modify() to add or modify existing VLAN record's
masks
- add cpsw_ale_set_unreg_mcast() for enabling unreg mcast on port VLANs
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now untagged vlan traffic is not support on Host P0 port. This patch adds
in ALE context bitmap of VLANs for which Host P0 port bit set in Force
Untagged Packet Egress bitmask in VLANs ALE entries, and adds corresponding
check in VLAN incapsulation header parsing function cpsw_rx_vlan_encap().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean CPSW ALE on init and intf restart (up/down) to avoid reading obsolete
or garbage entries from ALE table.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If TI_DAVINCI_EMAC=y and GENERIC_ALLOCATOR is not set,
below erros can be seen:
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_desc_pool_destroy.isra.14':
davinci_cpdma.c:(.text+0x359): undefined reference to `gen_pool_size'
davinci_cpdma.c:(.text+0x365): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x373): undefined reference to `gen_pool_avail'
davinci_cpdma.c:(.text+0x37f): undefined reference to `gen_pool_size'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `__cpdma_chan_free':
davinci_cpdma.c:(.text+0x4a2): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_chan_submit_si':
davinci_cpdma.c:(.text+0x66c): undefined reference to `gen_pool_alloc_algo_owner'
davinci_cpdma.c:(.text+0x805): undefined reference to `gen_pool_free_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_ctlr_create':
davinci_cpdma.c:(.text+0xabd): undefined reference to `devm_gen_pool_create'
davinci_cpdma.c:(.text+0xb79): undefined reference to `gen_pool_add_owner'
drivers/net/ethernet/ti/davinci_cpdma.o: In function `cpdma_check_free_tx_desc':
davinci_cpdma.c:(.text+0x16c6): undefined reference to `gen_pool_avail'
This patch mades TI_DAVINCI_EMAC select GENERIC_ALLOCATOR.
Fixes: 99f6297182 ("net: ethernet: ti: cpsw: drop TI_DAVINCI_CPDMA config option")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update on more short variant for getting real clock in ns.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpdma_chan_split_pool() function is not used outside of
the driver, so make it static to avoid the following sparse
warning:
drivers/net/ethernet/ti/davinci_cpdma.c:725:5: warning: symbol 'cpdma_chan_split_pool' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases when the probe function fails the error path calls
cpsw_remove_dt() before calling platform_set_drvdata(). This is an
issue as cpsw_remove_dt() uses platform_get_drvdata() to retrieve the
cpsw_common data and leds to a NULL pointer exception. This patches
fixes it by calling platform_set_drvdata() earlier in the probe.
Fixes: 83a8471ba2 ("net: ethernet: ti: cpsw: refactor probe to group common hw initialization")
Reported-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use accessor functions for skb fragment's page_offset instead
of direct references, in preparation for bvec conversion.
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a return or break from the middle of the loop,
there is no put, thus causing a memory leak.
Hence, for function cpsw_probe_dt, create an extra label err_node_put
that puts the last used node and returns ret; modify the return
statements in the loop to save the return value in ret and goto this new
label.
For function cpsw_remove_dt, add an of_node_put before the break.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix excessive stack usage in cxgb4, from Arnd Bergmann.
2) Missing skb queue lock init in tipc, from Chris Packham.
3) Fix some regressions in ipv6 flow label handling, from Eric Dumazet.
4) Elide flow dissection of local packets in FIB rules, from Petar
Penkov.
5) Fix TLS support build failure in mlx5, from Tariq Toukab.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ppp: mppe: Revert "ppp: mppe: Add softdep to arc4"
net: dsa: qca8k: replace legacy gpio include
net: hisilicon: Use devm_platform_ioremap_resource
cxgb4: reduce kernel stack usage in cudbg_collect_mem_region()
tipc: ensure head->lock is initialised
tc-tests: updated skbedit tests
nfp: flower: ensure ip protocol is specified for L4 matches
nfp: flower: fix ethernet check on match fields
net/mlx5e: Provide cb_list pointer when setting up tc block on rep
net: phy: make exported variables non-static
net: sched: Fix NULL-pointer dereference in tc_indr_block_ing_cmd()
davinci_cpdma: don't cast dma_addr_t to pointer
net: openvswitch: do not update max_headroom if new headroom is equal to old headroom
net/mlx5e: Convert single case statement switch statements into if statements
net/mlx5: E-Switch, Reduce ingress acl modify metadata stack usage
net/mlx5e: Fix unused variable warning when CONFIG_MLX5_ESWITCH is off
net/mlx5e: Fix compilation error in TLS code
ipv6: fix static key imbalance in fl_create()
ipv6: fix potential crash in ip6_datagram_dst_update()
ipv6: tcp: fix flowlabels reflection for RST packets
...
dma_addr_t may be 64-bit wide on 32-bit architectures, so it is not
valid to cast between it and a pointer:
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_chan_submit_si':
drivers/net/ethernet/ti/davinci_cpdma.c:1047:12: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_chan_idle_submit_mapped':
drivers/net/ethernet/ti/davinci_cpdma.c:1114:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_chan_submit_mapped':
drivers/net/ethernet/ti/davinci_cpdma.c:1164:12: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
Solve this by using two separate members in 'struct submit_info'.
Since this avoids the use of the 'flag' member, the structure does
not even grow in typical configurations.
Fixes: 6670acacd5 ("net: ethernet: ti: davinci_cpdma: add dma mapped submit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Add XDP support based on rx page_pool allocator, one frame per page.
Page pool allocator is used with assumption that only one rx_handler
is running simultaneously. DMA map/unmap is reused from page pool
despite there is no need to map whole page.
Due to specific of cpsw, the same TX/RX handler can be used by 2
network devices, so special fields in buffer are added to identify
an interface the frame is destined to. Thus XDP works for both
interfaces, that allows to test xdp redirect between two interfaces
easily. Also, each rx queue have own page pools, but common for both
netdevs.
XDP prog is common for all channels till appropriate changes are added
in XDP infrastructure. Also, once page_pool recycling becomes part of
skb netstack some simplifications can be added, like removing
page_pool_release_page() before skb receive.
In order to keep rx_dev while redirect, that can be somehow used in
future, do flush in rx_handler, that allows to keep rx dev the same
while redirect. It allows to conform with tracing rx_dev pointed
by Jesper.
Also, there is probability, that XDP generic code can be extended to
support multi ndev drivers like this one, using same rx queue for
several ndevs, based on switchdev for instance or else. In this case,
driver can be modified like exposed here:
https://lkml.org/lkml/2019/7/3/243
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That's possible to set channel num while interfaces are down. When
interface gets up it should resplit budget. This resplit can happen
after phy is up but only if speed is changed, so should be set before
this, for this allow it to happen while changing number of channels,
when interfaces are down.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
