Under certain circumstances, the timing settings calculated by
the FSMC NAND controller driver were inaccurate.
These settings led to incorrect data reads or fallback to
timing mode 0 depending on the NAND chip used.
The timing computation did not take into account the following
constraint given in SPEAr3xx reference manual:
twait >= tCEA - (tset * TCLK) + TOUTDEL + TINDEL
Enhance the timings calculation by taking into account this
additional constraint.
This change has no impact on slow timing modes such as mode 0.
Indeed, on mode 0, computed values are the same with and
without the patch.
NANDs which previously stayed in mode 0 because of fallback to
mode 0 can now work at higher speeds and NANDs which were not
working at all because of the corrupted data work at high
speeds without troubles.
Overall improvement on a Micron/MT29F1G08 (flash_speed tool):
mode0 mode3
eraseblock write speed 3220 KiB/s 4511 KiB/s
eraseblock read speed 4491 KiB/s 7529 KiB/s
Fixes: d9fb079571 ("mtd: nand: fsmc: add support for SDR timings")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-5-herve.codina@bootlin.com
The FSMC NAND controller should apply a delay after the
instruction has been issued on the bus.
The FSMC NAND controller driver did not handle this delay.
Add this waiting delay in the FSMC NAND controller driver.
Fixes: 4da712e702 ("mtd: nand: fsmc: use ->exec_op()")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-4-herve.codina@bootlin.com
When the NV-DDR interface is not supported by the NAND chip,
the value of onfi->nvddr_timing_modes is 0. In this case,
the best_mode variable value in nand_choose_best_nvddr_timings()
is -1. The last for-loop is skipped and the function returns an
uninitialized value.
If this returned value is 0, the nand_choose_best_sdr_timings()
is not executed and no 'best timing' are set. This leads the host
controller and the NAND chip working at default mode 0 timing
even if a better timing can be used.
Fix this uninitialized returned value.
nand_choose_best_sdr_timings() is pretty similar to
nand_choose_best_nvddr_timings(). Even if onfi->sdr_timing_modes
should never be seen as 0, nand_choose_best_sdr_timings() returned
value is fixed.
Fixes: a9ecc8c814 ("mtd: rawnand: Choose the best timings, NV-DDR included")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-3-herve.codina@bootlin.com
NAND_OP_CMD() expects a delay parameter in nanoseconds.
The delay value is wrongly given in milliseconds.
Fix the conversion macro used in order to set this
delay in nanoseconds.
Fixes: d7a773e881 ("mtd: rawnand: Access SDR and NV-DDR timings through a common macro")
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211119150316.43080-2-herve.codina@bootlin.com
The helper function devm_platform_ioremap_resource_xxx()
needs HAS_IOMEM enabled, so add the dependency on HAS_IOMEM.
Fixes: 5f14a8ca1b ("mtd: rawnand: denali: Make use of the helper function devm_platform_ioremap_resource_byname()")
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211109134758.417-1-caihuoqing@baidu.com
gpmi_io clock needs to be gated off when changing the parent/dividers of
enfc_clk_root (i.MX6Q/i.MX6UL) respectively qspi2_clk_root (i.MX6SX).
Otherwise this rate change can lead to an unresponsive GPMI core which
results in DMA timeouts and failed driver probe:
[ 4.072318] gpmi-nand 112000.gpmi-nand: DMA timeout, last DMA
...
[ 4.370355] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -110
...
[ 4.375988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.381524] gpmi-nand 112000.gpmi-nand: Error in ECC-based read: -22
[ 4.387988] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
[ 4.393535] gpmi-nand 112000.gpmi-nand: Chip: 0, Error -22
...
Other than stated in i.MX 6 erratum ERR007117, it should be sufficient
to gate only gpmi_io because all other bch/nand clocks are derived from
different clock roots.
The i.MX6 reference manuals state that changing clock muxers can cause
glitches but are silent about changing dividers. But tests showed that
these glitches can definitely happen on i.MX6ULL. For i.MX7D/8MM in turn,
the manual guarantees that no glitches can happen when changing
dividers.
Co-developed-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Christian Eggers <ceggers@arri.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-2-ceggers@arri.de
There is no need to explicitly set the default gpmi clock rate during
boot for the i.MX 6 since this is done during nand_detect anyway.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Cc: stable@vger.kernel.org
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211102202022.15551-1-ceggers@arri.de
The ECC engine on the JZ4740 SoC requires the ECC data to be read before
the page; using the default page reading function does not work. Indeed,
the old JZ4740 NAND driver (removed in 5.4) did use the 'OOB first' flag
that existed back then.
Use the newly created nand_read_page_hwecc_oob_first() to address this
issue.
This issue was not found when the new ingenic-nand driver was developed,
most likely because the Device Tree used had the nand-ecc-mode set to
"hw_oob_first", which seems to not be supported anymore.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-5-paul@crapouillou.net
Move the function nand_read_page_hwecc_oob_first() (previously
nand_davinci_read_page_hwecc_oob_first()) to nand_base.c, and export it
as a GPL symbol, so that it can be used by more modules.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-4-paul@crapouillou.net
The original comment that describes the function
nand_davinci_read_page_hwecc_oob_first() is very obscure and it is hard
to understand what it is for.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-3-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() first reads the
OOB data, extracts the ECC information, programs the ECC hardware before
reading the actual data in a loop.
Right after the OOB data was read, it called nand_read_page_op() to
reset the read cursor to the beginning of the page. This caused the
first page to be read twice: in that call, and later in the loop.
Address that issue by changing the call to nand_read_page_op() to
nand_change_read_column_op(), which will only reset the read cursor.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-2-paul@crapouillou.net
The function nand_davinci_read_page_hwecc_oob_first() does read the ECC
data from the OOB area. Therefore it does not need to calculate the ECC
as it is already available.
Cc: <stable@vger.kernel.org> # v5.2
Fixes: a0ac778eb8 ("mtd: rawnand: ingenic: Add support for the JZ4740")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211016132228.40254-1-paul@crapouillou.net
* Remove obsolete macros only used by the old nand_ecclayout struct
* Don't remove debugfs directory if device is in use
* MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
* block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
* mtdswap: Remove redundant assignment of pointer eb
CFI:
* Fixup CFI on ixp4xx
Raw NAND controller drivers:
* Arasan:
- Prevent an unsupported configuration
* Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd, AMS-Delta:
- Keep the driver compatible with on-die ECC engines
* cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
* Fsmc: Fix use of SM ORDER
* Intel:
- Fix potential buffer overflow in probe
* xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk, hisi504,
gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
* Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
* Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
* Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
* Enable locking for n25q128a13
SPI NOR controller drivers:
* Use devm_platform_ioremap_resource_byname()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmGIAdEACgkQJWrqGEe9
VoQHEAgAkFvFxIOyPSwAJfyeEklWmGSh+cm+X9EqWxZ5d6iwFE3FZH4X4XiqdyVY
+rzy37o6Tp3pQVYDqxmPM8GGoHy8wYPR5h/U1IozbBaNeCJma1HyK4Sjb/cuX1eQ
23EM1pWT8N9CbRG2S9mz5C9uHcP9mImtyvU4WhTLKOEc9XGbpuj+k1cacSuEEbeF
rZklOa7tvUiOFIDfr7Kf+DfxbpYabgB2dJgWPEtZmKmefWMiODHgvBJo0MT6MKr7
kOlIkgq5zYIFRNaxApWLI3JmH9+lsw6MHBe+cCqemV6q2OZlMV/5VGFElEywJt+4
L3VmlJQpMiCEMo2Cgc1jigHKryk4Xw==
=h6o3
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"Core:
- Remove obsolete macros only used by the old nand_ecclayout struct
- Don't remove debugfs directory if device is in use
- MAINTAINERS:
- Add entry for Qualcomm NAND controller driver
- Update the devicetree documentation path of hyperbus
MTD devices:
- block2mtd:
- Add support for an optional custom MTD label
- Minor refactor to avoid hard coded constant
- mtdswap: Remove redundant assignment of pointer eb
CFI:
- Fixup CFI on ixp4xx
Raw NAND controller drivers:
- Arasan:
- Prevent an unsupported configuration
- Xway, Socrates: plat_nand, Pasemi, Orion, mpc5121, GPIO, Au1550nd,
AMS-Delta:
- Keep the driver compatible with on-die ECC engines
- cs553x, lpc32xx_slc, ndfc, sharpsl, tmio, txx9ndfmc:
- Revert the commits: "Fix external use of SW Hamming ECC helper"
- And let callers use the bare Hamming helpers
- Fsmc: Fix use of SM ORDER
- Intel:
- Fix potential buffer overflow in probe
- xway, vf610, txx9ndfm, tegra, stm32, plat_nand, oxnas, omap, mtk,
hisi504, gpmi, gpio, denali, bcm6368, atmel:
- Make use of the helper function devm_platform_ioremap_resource{,byname}()
Onenand drivers:
- Samsung: Drop Exynos4 and describe driver in KConfig
Raw NAND chip drivers:
- Hynix: Add support for H27UCG8T2ETR-BC MLC NAND
SPI NOR core:
- Add spi-nor device tree binding under SPI NOR maintainers
SPI NOR manufacturer drivers:
- Enable locking for n25q128a13
SPI NOR controller drivers:
- Use devm_platform_ioremap_resource_byname()"
* tag 'mtd/for-5.16' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (50 commits)
mtd: core: don't remove debugfs directory if device is in use
MAINTAINERS: Update the devicetree documentation path of hyperbus
mtd: block2mtd: add support for an optional custom MTD label
mtd: block2mtd: minor refactor to avoid hard coded constant
mtd: fixup CFI on ixp4xx
mtd: rawnand: arasan: Prevent an unsupported configuration
MAINTAINERS: Add entry for Qualcomm NAND controller driver
mtd: rawnand: hynix: Add support for H27UCG8T2ETR-BC MLC NAND
mtd: rawnand: xway: Keep the driver compatible with on-die ECC engines
mtd: rawnand: socrates: Keep the driver compatible with on-die ECC engines
mtd: rawnand: plat_nand: Keep the driver compatible with on-die ECC engines
mtd: rawnand: pasemi: Keep the driver compatible with on-die ECC engines
mtd: rawnand: orion: Keep the driver compatible with on-die ECC engines
mtd: rawnand: mpc5121: Keep the driver compatible with on-die ECC engines
mtd: rawnand: gpio: Keep the driver compatible with on-die ECC engines
mtd: rawnand: au1550nd: Keep the driver compatible with on-die ECC engines
mtd: rawnand: ams-delta: Keep the driver compatible with on-die ECC engines
Revert "mtd: rawnand: cs553x: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: lpc32xx_slc: Fix external use of SW Hamming ECC helper"
Revert "mtd: rawnand: ndfc: Fix external use of SW Hamming ECC helper"
...
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde60314 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
Add support for the H27UCG8T2ETR-BC MLC NAND. The NAND is used widely
in the NTC CHIP, is an MLC type NAND, and is 8GB in size. Neither
JEDEC nor ONFI detection identifies it correctly, so the ID is added
to the nand_ids.c file. Additionally, per the datasheet this NAND
appears to use the same paired pages scheme as the Toshiba
TC58TEG5DCLTA00 (dist3), so add support for that to enable use in
SLC emulation mode.
Tested on a NTC CHIP the device is able to write to a ubifs formatted
partition, and then have U-Boot (with proposed patches) boot from a
kernel located on that ubifs formatted partition.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210930162402.344-1-macroalpha82@gmail.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d9347332 ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
This reverts commit 56a8d3fd1f.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-9-miquel.raynal@bootlin.com
This reverts commit c4b7d7c480.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-8-miquel.raynal@bootlin.com
This reverts commit 3e09c02525.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-7-miquel.raynal@bootlin.com
This reverts commit 46fcb57e6b.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-6-miquel.raynal@bootlin.com
This reverts commit 6a4c5ada57.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-5-miquel.raynal@bootlin.com
This reverts commit 3d227a0b0c.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-4-miquel.raynal@bootlin.com
The introduction of the generic ECC engine API lead to a number of
changes in various drivers which broke some of them. Here is a typical
example: I expected the SM_ORDER option to be handled by the Hamming ECC
engine internals. Problem: the fsmc driver does not instantiate (yet) a
real ECC engine object so we had to use a 'bare' ECC helper instead of
the shiny rawnand functions. However, when not intializing this engine
properly and using the bare helpers, we do not get the SM ORDER feature
handled automatically. It looks like this was lost in the process so
let's ensure we use the right SM ORDER now.
Fixes: ad9ffdce45 ("mtd: rawnand: fsmc: Fix external use of SW Hamming ECC helper")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-2-miquel.raynal@bootlin.com
From QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".
qcom_nandc_read_cw_raw() is used to read only one code word
at a time. If we will configure number of code words to 1 in
in QPIC_NAND_DEV0_CFG0 register then QPIC controller thinks
its reading the last code word, since from QPIC V2 onwards
we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n"
register to fetch data from controller buffer to system
memory.
Fixes: 503ee5aad4 ("mtd: rawnand: qcom: update last code word register")
Cc: stable@kernel.org
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1630998357-1359-1-git-send-email-mdalam@codeaurora.org
ebu_nand_probe() read the value of u32 variable "cs" from the device
firmware description and used it as the index for array ebu_host->cs
that can contain MAX_CS (2) elements at most. That could result in
a buffer overflow and various bad consequences later.
Fix the potential buffer overflow by restricting values of "cs" with
MAX_CS in probe.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210903082653.16441-1-novikov@ispras.ru
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074252.9633-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074245.9583-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074237.9533-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074230.9483-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074222.9433-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074215.9383-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074207.9333-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074200.9283-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074153.9233-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074145.9183-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074138.9133-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074130.9083-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074123.9033-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074116.8983-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074108.8933-1-caihuoqing@baidu.com
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210901074031.8883-1-caihuoqing@baidu.com
Merge more updates from Andrew Morton:
"147 patches, based on 7d2a07b769.
Subsystems affected by this patch series: mm (memory-hotplug, rmap,
ioremap, highmem, cleanups, secretmem, kfence, damon, and vmscan),
alpha, percpu, procfs, misc, core-kernel, MAINTAINERS, lib,
checkpatch, epoll, init, nilfs2, coredump, fork, pids, criu, kconfig,
selftests, ipc, and scripts"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (94 commits)
scripts: check_extable: fix typo in user error message
mm/workingset: correct kernel-doc notations
ipc: replace costly bailout check in sysvipc_find_ipc()
selftests/memfd: remove unused variable
Kconfig.debug: drop selecting non-existing HARDLOCKUP_DETECTOR_ARCH
configs: remove the obsolete CONFIG_INPUT_POLLDEV
prctl: allow to setup brk for et_dyn executables
pid: cleanup the stale comment mentioning pidmap_init().
kernel/fork.c: unexport get_{mm,task}_exe_file
coredump: fix memleak in dump_vma_snapshot()
fs/coredump.c: log if a core dump is aborted due to changed file permissions
nilfs2: use refcount_dec_and_lock() to fix potential UAF
nilfs2: fix memory leak in nilfs_sysfs_delete_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_create_snapshot_group
nilfs2: fix memory leak in nilfs_sysfs_delete_##name##_group
nilfs2: fix memory leak in nilfs_sysfs_create_##name##_group
nilfs2: fix NULL pointer in nilfs_##name##_attr_release
nilfs2: fix memory leak in nilfs_sysfs_create_device_group
trap: cleanup trap_init()
init: move usermodehelper_enable() to populate_rootfs()
...
HZ unit conversion macros are available in units.h, use them and remove
the duplicate definition.
Link: https://lkml.kernel.org/r/20210816114732.1834145-10-daniel.lezcano@linaro.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: Christian Eggers <ceggers@arri.de>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Lukasz Luba <lukasz.luba@arm.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* blkdevs:
- Simplify the refcounting in blktrans_{open, release}
- Simplify blktrans_getgeo
- Remove blktrans_ref_mutex
- Simplify blktrans_dev_get
- Use lockdep_assert_held
- Don't hold del_mtd_blktrans_dev in blktrans_{open, release}
* ftl:
- Don't cast away the type when calling add_mtd_blktrans_dev
- Don't cast away the type when calling add_mtd_blktrans_dev
- Use container_of() rather than cast
- Fix use-after-free
- Add discard support
- Allow use of MTD_RAM for testing purposes
* concat:
- Check _read, _write callbacks existence before assignment
- Judge callback existence based on the master
* maps:
- Maps: remove dead MTD map driver for PMC-Sierra MSP boards
* mtdblock:
- Warn if added for a NAND device
- Add comment about UBI block devices
- Update old JFFS2 mention in Kconfig
* partitions:
- Redboot: convert to YAML
NAND core changes:
* Repair Miquel Raynal's email address in MAINTAINERS
* Fix a couple of spelling mistakes in Kconfig
* bbt: Skip bad blocks when searching for the BBT in NAND
* Remove never changed ret variable
Raw NAND changes:
* cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
* intel: Fix error handling in probe
* omap: Fix kernel doc warning on 'calcuate' typo
* gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
* Properly fill the OOB area.
* Fix comment
SPI-NAND drivers changes:
* macronix: Add Quad support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmExS1gACgkQJWrqGEe9
VoSZcAf/SsUDpp/lqc+no4R+eUR/CWrbr3AKu2JjjgCJt0HK++Fy8LQU3FEjn9E8
CNBWYqIVVit1XhqGu192wh0ESsHGlNwjicB3Ul4/RFFC4WKs68kQe0gQrU6z/95V
jaTOW+B7PZh6MFbQROUVI97Cs3OTd8vCE3L2SgIW6krk8tnOEyddlgFsWLISjk6g
Ut1I473653fJAcr5OXEFJLWF+01q2azR9AiAkfKC47IUekTRJqjK2YJpAhsdf4hi
xqazp79sbcNXSHCgOOQv4/f03+SAiufRcNgztwrSWw2fdCg0csBC9ACwmdhhGGfd
7uFn+/Q3sVDOKTN7aAWW1KnykKXsJw==
=JFrk
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD changes:
- blkdevs:
- Simplify the refcounting in blktrans_{open, release}
- Simplify blktrans_getgeo
- Remove blktrans_ref_mutex
- Simplify blktrans_dev_get
- Use lockdep_assert_held
- Don't hold del_mtd_blktrans_dev in blktrans_{open, release}
- ftl:
- Don't cast away the type when calling add_mtd_blktrans_dev
- Don't cast away the type when calling add_mtd_blktrans_dev
- Use container_of() rather than cast
- Fix use-after-free
- Add discard support
- Allow use of MTD_RAM for testing purposes
- concat:
- Check _read, _write callbacks existence before assignment
- Judge callback existence based on the master
- maps:
- Maps: remove dead MTD map driver for PMC-Sierra MSP boards
- mtdblock:
- Warn if added for a NAND device
- Add comment about UBI block devices
- Update old JFFS2 mention in Kconfig
- partitions:
- Redboot: convert to YAML
NAND core changes:
- Repair Miquel Raynal's email address in MAINTAINERS
- Fix a couple of spelling mistakes in Kconfig
- bbt: Skip bad blocks when searching for the BBT in NAND
- Remove never changed ret variable
Raw NAND changes:
- cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
- intel: Fix error handling in probe
- omap: Fix kernel doc warning on 'calcuate' typo
- gpmc: Fix the ECC bytes vs. OOB bytes equation
SPI-NAND core changes:
- Properly fill the OOB area.
- Fix comment
SPI-NAND drivers changes:
- macronix: Add Quad support for serial NAND flash"
* tag 'mtd/for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (30 commits)
mtd: rawnand: cafe: Fix a resource leak in the error handling path of 'cafe_nand_probe()'
mtd_blkdevs: simplify the refcounting in blktrans_{open, release}
mtd_blkdevs: simplify blktrans_getgeo
mtd_blkdevs: remove blktrans_ref_mutex
mtd_blkdevs: simplify blktrans_dev_get
mtd/rfd_ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd/ftl: don't cast away the type when calling add_mtd_blktrans_dev
mtd_blkdevs: use lockdep_assert_held
mtd_blkdevs: don't hold del_mtd_blktrans_dev in blktrans_{open, release}
mtd: rawnand: intel: Fix error handling in probe
mtd: mtdconcat: Check _read, _write callbacks existence before assignment
mtd: mtdconcat: Judge callback existence based on the master
mtd: maps: remove dead MTD map driver for PMC-Sierra MSP boards
mtd: rfd_ftl: use container_of() rather than cast
mtd: rfd_ftl: fix use-after-free
mtd: rfd_ftl: add discard support
mtd: rfd_ftl: allow use of MTD_RAM for testing purposes
mtdblock: Warn if added for a NAND device
mtd: spinand: macronix: Add Quad support for serial NAND flash
mtdblock: Add comment about UBI block devices
...
A successful 'init_rs_non_canonical()' call should be balanced by a
corresponding 'free_rs()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: 8c61b7a7f4 ("[MTD] [NAND] Use rslib for CAFÉ ECC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/fd313d3fb787458bcc73189e349f481133a2cdc9.1629532640.git.christophe.jaillet@wanadoo.fr
ebu_nand_probe() did not invoke ebu_dma_cleanup() and
clk_disable_unprepare() on some error handling paths. The patch fixes
that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Signed-off-by: Kirill Shilimanov <kirill.shilimanov@huawei.com>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210817092930.23040-1-novikov@ispras.ru
The ret variable used for returning value in the function
`meson_nfc_rw_cmd_prepare_and_execute` is never change after initialising.
Therefore, we can remove it safely and return 0 at the end of the function.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210803113300.24230-1-wangborong@cdjrlc.com
Fix a trivial typo which is reported after enabling W=1 level of warnings:
drivers/mtd/nand/raw/omap2.c:927: warning: expecting prototype
for omap_calcuate_ecc(). Prototype was for omap_calculate_ecc() instead
Signed-off-by: Vladimir Molokov <vladimir@molokov.se>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210801205909.7102-1-vladimir@molokov.se
Due to 14f97f0b8e, the rawnand platforms without "secure-regions"
property defined in DT fails to probe. The issue is,
of_get_nand_secure_regions() errors out if
of_property_count_elems_of_size() returns a negative error code.
If the "secure-regions" property is not present in DT, then also we'll
get -EINVAL from of_property_count_elems_of_size() but it should not
be treated as an error for platforms not declaring "secure-regions"
in DT.
So fix this behaviour by checking for the existence of that property in
DT and return 0 if it is not present.
Fixes: 14f97f0b8e ("mtd: rawnand: Add a check in of_get_nand_secure_regions()")
Reported-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Tested-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210727062813.32619-1-manivannan.sadhasivam@linaro.org
The blocks containing the bad block table can become bad as well. So
make sure to skip any blocks that are marked bad when searching for the
bad block table.
Otherwise in very rare cases where two BBT blocks wear out it might
happen that an obsolete BBT is used instead of a newer available
version.
This only applies to drivers which make use of a bad block marker in flash.
Other drivers won't be able to identify bad BBT blocks and thus can't skip
these.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210625123821.207458-1-s.riedmueller@phytec.de
Check for whether of_property_count_elems_of_size() returns a negative
error code.
Fixes: 13b8976827 ("mtd: rawnand: Add support for secure regions in NAND memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YMtQFXE0F1w7mUh+@mwanda
* Convert list_for_each to entry variant
* Use MTD_DEVICE_ATTR_RO/RW() helper macros
* Remove unnecessary OOM messages
* Potential NULL dereference in mtd_otp_size()
* Fix freeing of otp_info buffer
* Create partname and partid debug files for child MTDs
* tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
* Add OTP NVMEM provider support
* Allow specifying of_node
* Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
* Convert ti,am654-hbmc.txt to YAML schema
* spi-nor: add otp property
* Add OTP bindings
* add YAML schema for the generic MTD bindings
* Add brcm,trx-magic
MTD device drivers changes:
* Add support for microchip 48l640 EERAM
* Remove superfluous "break"
* sm_ftl:
- Fix alignment of block comment
* nftl:
- Return -ENOMEM when kmalloc failed
* nftlcore:
- Remove set but rewrite variables
* phram:
- Fix error return code in phram_setup()
* plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
* Qcom:
- Fix leaking of partition name
* Redboot:
- Fix style issues
- Seek fis-index-block in the right node
* trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
* Ability to dump SFDP tables via sysfs
* Support for erasing OTP regions on Winbond and similar flashes
* Few API doc updates and fixes
* Locking support for MX25L12805D
SPI NOR controller drivers changes:
* Use SPI_MODE_X_MASK in nxp-spifi
* Intel Alder Lake-M SPI serial flash support
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDcT+IACgkQJWrqGEe9
VoT5Sgf/dt92XA5K2SYNh58KPUwemB9DtkukmniGjo9AqSQwuzHxik3ITHBbFvwP
cSj5PAGoI+zpc+VQz+XuZF1Bsmxaqhy5c0aaJ9TZai2W6keB91in7nJPAhmAI5o2
4zhtAZ9qKp4pOwhFqn6jTd5+l38ok50go3HB4Ibw4UlLuvbUEv11DUcXGKnaAadH
tmXZALf65YAJVruPb4yw+cv7BVVgOPQL8C8ILtsrue7Zgya3JT1205Zbfdjo+X0v
Kl2gh7gGh1YLqzuLLBDUiDnfLIfiu/WTnPqxtqCULR9cLG4oXybXHZe9OsrP8E+P
T68+K8VvT5LKbGh47/OoUfLvrDguCA==
=XVaS
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Convert list_for_each to entry variant
- Use MTD_DEVICE_ATTR_RO/RW() helper macros
- Remove unnecessary OOM messages
- Potential NULL dereference in mtd_otp_size()
- Fix freeing of otp_info buffer
- Create partname and partid debug files for child MTDs
- tests:
- Remove redundant assignment to err
- Fix error return code in mtd_oobtest_init()
- Add OTP NVMEM provider support
- Allow specifying of_node
- Convert sysfs sprintf/snprintf family to sysfs_emit
Bindings changes:
- Convert ti,am654-hbmc.txt to YAML schema
- spi-nor: add otp property
- Add OTP bindings
- add YAML schema for the generic MTD bindings
- Add brcm,trx-magic
MTD device drivers changes:
- Add support for microchip 48l640 EERAM
- Remove superfluous "break"
- sm_ftl:
- Fix alignment of block comment
- nftl:
- Return -ENOMEM when kmalloc failed
- nftlcore:
- Remove set but rewrite variables
- phram:
- Fix error return code in phram_setup()
- plat-ram:
- Remove redundant dev_err call in platram_probe()
MTD parsers changes:
- Qcom:
- Fix leaking of partition name
- Redboot:
- Fix style issues
- Seek fis-index-block in the right node
- trx:
- Allow to use TRX parser on Mediatek SoCs
- Allow to specify brcm, trx-magic in DT
Raw NAND core:
- Allow SDR timings to be nacked
- Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing
set.
- Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
- Update dead URL
- Silence static checker warning in nand_setup_interface()
- BBT:
- Fix corner case in bad block table handling
- onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
- Atmel:
- Ensure the data interface is supported.
- Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
- brcmnand:
- Convert bindings to json-schema
- OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
- PL35X:
- New driver
- QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
- Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in
marvell_nfc_resume()
- R852:
- Use DEVICE_ATTR_RO() helper macro
- MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
- HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
- Light reorganisation for the introduction of a core resume handler
- Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
- Macronix:
- Add support for serial NAND flash
SPI NOR core changes:
- Ability to dump SFDP tables via sysfs
- Support for erasing OTP regions on Winbond and similar flashes
- Few API doc updates and fixes
- Locking support for MX25L12805D
SPI NOR controller drivers changes:
- Use SPI_MODE_X_MASK in nxp-spifi
- Intel Alder Lake-M SPI serial flash support"
* tag 'mtd/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (125 commits)
mtd: spi-nor: remove redundant continue statement
mtd: rawnand: omap: Add larger page NAND chips support
mtd: rawnand: omap: Various style fixes
mtd: rawnand: omap: Check return values
mtd: rawnand: omap: Rename a macro
mtd: rawnand: omap: Aggregate the HW configuration of the ELM
mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller
dt-bindings: mtd: pl353-nand: Describe this hardware controller
MAINTAINERS: Add PL353 NAND controller entry
mtd: rawnand: qcom: avoid writing to obsolete register
mtd: rawnand: marvell: Minor documentation correction
mtd: rawnand: r852: use DEVICE_ATTR_RO() helper macro
mtd: spinand: add SPI-NAND MTD resume handler
mtd: spinand: Add spinand_init_flash() helper
mtd: spinand: add spinand_read_cfg() helper
mtd: rawnand: marvell: add missing clk_disable_unprepare() on error in marvell_nfc_resume()
mtd: rawnand: arasan: Finer grain NV-DDR configuration
mtd: rawnand: arasan: Rename the data interface register
mtd: rawnand: onfi: Fix endianness when reading NV-DDR values
mtd: rawnand: arasan: Use the right DMA mask
...
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmDS290ACgkQJWrqGEe9
VoS77wgAgKnqfFwbqzdSecVmXai9roSNHi/aMpVJvvLHSTCV35iCcNNtrz0Jno56
t/8twVPPZUI6f3vPXk5+NjKRCb8Oif3oU+tNxqG6mwzrBRf5R80pYCMm+HGPWZaK
+MolqGAbgFO088DTK5fGNtmbnb5fPT174RKRBGEH5NgK5M1q95uF8fIjBXDcjVe2
hvAyoqqC7i/bp40sxRtglgBpYYz+KUjCX11JvJPa5IuVU+8ezZSKJLSo5/CtgIKJ
mRQ8p8myiUjZngcnebjTrAA5AwQ13ai9ofKG0pHkdxwOq4lSRNgKou0Hk5+oq+s0
BFEuXnUrdnJNU7+XV+kAqBoT6WOFzg==
=I/9X
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core:
* Allow SDR timings to be nacked
* Bring support for NV-DDR timings which involved a number of small
preparation changes to bring new helpers, properly introduce NV-DDR
structures, fill them, differenciate them and pick the best timing set.
* Add the necessary infrastructure to parse the new gpio-cs property
which aims at enlarging the number of available CS when a hardware
controller is too constrained.
* Update dead URL
* Silence static checker warning in nand_setup_interface()
* BBT:
- Fix corner case in bad block table handling
* onfi:
- Use more recent ONFI specification wording
- Use the BIT() macro when possible
Raw NAND controller drivers:
* Atmel:
- Ensure the data interface is supported.
* Arasan:
- Finer grain NV-DDR configuration
- Rename the data interface register
- Use the right DMA mask
- Leverage additional GPIO CS
- Ensure proper configuration for the asserted target
- Add support for the NV-DDR interface
- Fix a macro parameter
* brcmnand:
- Convert bindings to json-schema
* OMAP:
- Various fixes and style improvements
- Add larger page NAND chips support
* PL35X:
- New driver
* QCOM:
- Avoid writing to obsolete register
- Delete an unneeded bool conversion
- Allow override of partition parser
* Marvell:
- Minor documentation correction
- Add missing clk_disable_unprepare() on error in marvell_nfc_resume()
* R852:
- Use DEVICE_ATTR_RO() helper macro
* MTK:
- Remove redundant dev_err call in mtk_ecc_probe()
* HISI504:
- Remove redundant dev_err call in probe
SPI-NAND core:
* Light reorganisation for the introduction of a core resume handler
* Fix double counting of ECC stats
SPI-NAND manufacturer drivers:
* Macronix:
- Add support for serial NAND flash
There is no reason to be limited to 4kiB page NAND chips just because
this is the maximum length the ELM is able to handle in one go. Just
call the ELM several times and it will process as many data as needed.
Here we introduce the concept of ECC page (which is at most 4kiB). The
ELM will be sought as many times as there are ECC pages.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ryan Barnett <ryan.barnett@collins.com>
Link: https://lore.kernel.org/linux-mtd/20210610134906.3503303-6-miquel.raynal@bootlin.com
The macro BADBLOCK_MARKER_LENGTH is pretty long and could be reduced to
BBM_LEN which is more handy to use in the code.
This is a purely cosmetic change and is only done to avoid further
change to contain 100+ char lines just because of this definition.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610134906.3503303-3-miquel.raynal@bootlin.com
This hardware controller is embedded in XilinX Zynq-7000 SoCs and has
partial support for Hamming ECC correction.
This work is inspired from the original contributions of Punnaiah
Choudary Kalluri and Naga Sureshkumar Relli.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Michael Walle <michael@walle.cc> [on zynq-7000]
Link: https://lore.kernel.org/linux-mtd/20210610082040.2075611-19-miquel.raynal@bootlin.com
There are 2 timing registers:
- "data interface"
- "timings"
So far, the "data interface" register was named "timings" which begins
misleading when bringing support for the "timings" register. Rename it
to "data_iface".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084959.208804-1-miquel.raynal@bootlin.com
Without the use of le16_to_cpu(), these accesses would have been wrong
on a big-endian machine.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 45606518f9 ("mtd: rawnand: Add onfi_fill_nvddr_interface_config() helper")
Fixes: 9310668fb6 ("mtd: rawnand: Retrieve NV-DDR timing modes from the ONFI parameter page")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210527084913.208635-1-miquel.raynal@bootlin.com
Xilinx ZynqMP SoC and the Arasan controller support 64-bit DMA
addressing. Define the right mask otherwise the default is 32
and some accesses may overflow the default mask.
Reported-by: Jorge Courett <jorge.courett@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jorge Courett <jorge.courett@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20210527084548.208429-1-miquel.raynal@bootlin.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020958.15023-1-thunder.leizhen@huawei.com
Fixes scripts/checkpatch.pl warning:
WARNING: Possible unnecessary 'out of memory' message
Remove it can help us save a bit of memory.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210610020620.14970-1-thunder.leizhen@huawei.com
The result of an expression consisting of a single relational operator is
already of the bool type and does not need to be evaluated explicitly.
No functional change.
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210510114944.3527-1-thunder.leizhen@huawei.com
Make use of the cs-gpios DT property as well as the core helper to parse
it so that the Arasan controller driver can now assert many more chips
than natively.
The Arasan controller has an internal limitation: RB0 is tied to CS0 and
RB1 is tied to CS1. Hence, it is possible to use external GPIOs as long
as one or the other native CS is not used (or configured to be driven as
a GPIO) and that all additional CS are physically wired on its
corresponding RB line. Eg. CS0 is used as a native CS, CS1 is not used
as native CS and may be used as a GPIO CS, CS2 is an additional GPIO
CS. Then the target asserted by CS0 should also be wired to RB0, while
the targets asserted by CS1 and CS2 should be wired to RB1.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-5-miquel.raynal@bootlin.com
The controller being always asserting one CS or the other, there is no
need to actually select the right target before doing a page read/write.
However, the anfc_select_target() helper actually also changes the
timing configuration and clock in the case were two different NAND chips
with different timing requirements would be used. In this situation, we
must ensure proper configuration of the controller by calling it.
As a consequence of this change, the anfc_select_target() helper is
being moved earlier in the driver.
Fixes: 88ffef1b65 ("mtd: rawnand: arasan: Support the hardware BCH ECC engine")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-4-miquel.raynal@bootlin.com
New chips may feature a lot of CS because of their extended length. As
many controllers have been designed a decade ago, they usually only
feature just a couple. This does not mean that the entire range of
these chips cannot be accessed: it is just a matter of adding more
GPIO CS in the hardware design. A DT property has been added to
describe the CS array: cs-gpios.
Here is the code parsing it this new property, allocating what needs to
be, requesting the GPIOs and returning an array with the additional
available CS. The first entries of this array are left empty and are
reserved for native CS.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210526093242.183847-3-miquel.raynal@bootlin.com
As explained in the comment introduced above the fix, the Arasan
controller driver starts an operation when the prog register is being
written with a "type" specific to the action to perform.
The prog type used until now to perform a CHANGE READ COLUMN with an SDR
interface was the PAGE READ type (CMD + ADDR + CMD +
DATA). Unfortunately, for an unknown reason (let's call this a silicon
bug) any CHANGE READ COLUMN performed this way in NV-DDR mode will fail:
the data ready flag will never be triggered, nor will be the transfer
complete flag. Forcefully, this leads to a timeout situation which is
not easy to handle.
Fortunately, it was spotted that sending the same commands through a
different prog register "type", CHANGE READ COLUMN ENHANCED, would work
all the time (even though this particular command is not supported by
the core and is only available in a limited set of devices - we only
care about the controller configuration and not the actual command which
is sent to the device). So let's use this type instead when a CHANGE
READ COLUMN is requested.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-22-miquel.raynal@bootlin.com
Now that the necessary peaces to support the NV-DDR interface type have
been contributed, let's add the relevant logic to make use of it. In
particular, the core does not choose the best SDR timings anymore but
calls a more generic helper instead.
This helper checks if NV-DDR is supported by trying to find the best
NV-DDR supported mode through a logic very close to what is being done
for SDR timings. If no NV-DDR mode in common between the NAND controller
and the NAND chip is found, the core will fallback to SDR.
Side note: theoretically, the data clock speed in NV-DDR mode 0 is
slower than in SDR mode 5. In the situation where we would get a working
NV-DDR mode 0, we could also try if SDR mode 5 is supported and
eventually fallback to it in order to get the fastest possible
throughput. However, in the field, it looks like most of the devices
supporting NV-DDR avoid implementing the fastest SDR modes (like 4 and 5
EDO modes, which are a bit more complicated to handle than the other SDR
modes). So, we will stick to the simplest logic: try NV-DDR otherwise
fallback to SDR. If someone else experiences strong differences because
of that we may still implement the logic defined above.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-19-miquel.raynal@bootlin.com
Until now the parameter of the ADDR_TIMING_MODE feature was just the
ONFI timing mode (from 0 to 5) because we were only supporting the SDR
data interface. In the same byte, bits 4 and 5 indicate which data
interface is being configured so use them to set the right mode and also
read them back to ensure the right timing has been setup on the chip's
side.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-17-miquel.raynal@bootlin.com
Introduce a similar helper to onfi_find_closest_sdr_mode(), but for
NV-DDR timings. It just takes a timing structure as parameter and
returns the closest mode by comparing all minimum timings. This is
useful for rigid controllers on which tuning the timings is not
possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-16-miquel.raynal@bootlin.com
As explained in chapter "NV-DDR / NV-DDR2 / NV-DDR3 and Repeat Bytes" of
the ONFI specification, with some commands (mainly the commands which do
not transfer actual data) the data bytes are repeated twice and it is
the responsibility of the receiver to discard them properly. The
concerned commands are: SET_FEATURES, READ_ID, GET_FEATURES,
READ_STATUS, READ_STATUS_ENHANCED, ODT_CONFIGURE. Hence, in the NAND
core we are only impacted by the implementation of READ_ID, GET_FEATURES
and READ_STATUS.
The logic is the same for all:
2/ Check if it is relevant to read all data bytes twice.
1/ Allocate a buffer with twice the requested size (may be done
statically).
2/ Update the instruction structure to read these extra bytes in the
allocated buffer.
3/ Copy the even bytes into the original buffer. The performance hit is
negligible on such small data transfers anyway and we don't really
care about performances at this stage anyway.
4/ Free the allocated buffer, if any.
Note: nand_data_read_op() is also impacted because it is theoretically
possible to run the command/address cycles first, and, as another
operation, do the data transfers. In this case we can easily identify
the impacted commands because the force_8bit flag will be set (due to
the same reason: their data does not go through the same pipeline).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-15-miquel.raynal@bootlin.com
Most timings related to the bus timings are different between SDR and
NV-DDR. However, we identified 9 individual timings which are more
related to the NAND chip internals. These are common between the two
interface types. Fortunately, only these common timings are being shared
through the NAND core and its ->exec_op() interface, which allows the
writing of a simple macro checking the interface type and depending on
it, returning either the relevant SDR timing or the NV-DDR timing. This
is the purpose of the NAND_COMMON_TIMING_PS() macro.
As all this is evaluated at build time, one will immediately be notified
in case a non common timing is being accessed through this macro.
Two handy macros are also inserted at the same time, which use
PSEC_TO_NSEC or PSEC_TO_MSEC so that it is very easy to return timings
in milli-, nano- or pico-seconds, as usually requested by the internal
API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-14-miquel.raynal@bootlin.com
Legacy code should not benefit from newer features, especially in
helpers that have been deprecated for a very long time. People who want
NV-DDR support must migrate their driver to the ->exec_op() API.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-13-miquel.raynal@bootlin.com
Same logic as for the SDR path, let's create a
onfi_fill_nvddr_interface_config() helper to fill an interface
configuration structure with NV-DDR timings, given a specific ONFI mode.
There is one additional thing to do compared to SDR mode: tCAD timing
can be fast or slow and this depends on an ONFI parameter page bit. By
default the slow value is declared in the timings structure definition,
but this helper can shrink it down if necessary.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-12-miquel.raynal@bootlin.com
This helper actually fills the interface configuration with SDR data.
As part of the work to bring NV-DDR support, let's rename this helper
onfi_fill_sdr_interface_config() and add a generic indirection to it.
There are no functional changes here, but this will simplify a next
change which adds onfi_fill_nvddr_interface_config() support.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-11-miquel.raynal@bootlin.com
When parsing the ONFI parameter page, save the available NV-DDR timing
modes in the core's dynamic ONFI structure. Once available to the rest
of the core out of the ONFI driver, these values will then be used to
derive the best timing mode.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-10-miquel.raynal@bootlin.com
In particular, first ONFI specifications referred to SDR modes as
asynchronous modes, which is not the term we usually have in mind. The
spec has then been updated, so do the same here in the NAND subsystem to
avoid any possible confusion.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210505213750.257417-7-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-8-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-7-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-6-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-5-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Cc: Vladimir Zapolskiy <vz@mleia.com>
Reported-by: Trevor Woerner <twoerner@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Trevor Woerner <twoerner@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-4-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-3-miquel.raynal@bootlin.com
Since the Hamming software ECC engine has been updated to become a
proper and independent ECC engine, it is now mandatory to either
initialize the engine before using any one of his functions or use one
of the bare helpers which only perform the calculations. As there is no
actual need for a proper ECC initialization, let's just use the bare
helper instead of the rawnand one.
Fixes: 90ccf0a019 ("mtd: nand: ecc-hamming: Rename the exported functions")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210413161840.345208-2-miquel.raynal@bootlin.com
Commit 82bfd11f1b ("mtd: rawnand: qcom: Add support for Qcom SMEM
parser") made qcomsmem the only parser for qcom_nandc partitions. This
might be problematic for systems with both SPI and NAND MTD devices.
When booting from SPI flash the partition table should not apply to the
NAND flash.
Prepend cmdlinepart and ofpart parsers to allow override of the
partition parser.
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/cf470f05af514acd5bd94548804ffa96b966a0a8.1619029869.git.baruch@tkos.co.il
Smatch complains that the error code is not set on this error path:
drivers/mtd/nand/raw/nand_base.c:842 nand_setup_interface()
warn: missing error code 'ret'
But actually returning success is intentional because the NAND chip will
still work in mode 0. This patch adds a "ret = 0;" assignment to make
the intent more clear and to silence the static checker warning. It
doesn't affect the compiled code because GCC optimises the assignment
away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YH6Ugwz3gcga+q8X@mwanda
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210408111514.1011020-2-yukuai3@huawei.com
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Li <liwei391@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210407100526.3278741-1-liwei391@huawei.com
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
* Constify buf in mtd_write_user_prot_reg()
* Constify name param in mtd_bdi_init
* Fix fall-through warnings for Clang
* Get rid of Big MTD Lock ouf of mtdchar
* Drop mtd_mutex usage from mtdchar_open()
* Don't lock when recursively deleting partitions
* Use module_mtd_blktrans() to register driver when relevant
* Parse MTD as NVMEM cells
* New OTP (one-time-programmable) erase ioctl
* Require write permissions for locking and badblock ioctls
* physmap:
- Fix error return code of physmap_flash_remove()
- physmap-bt1-rom: Fix unintentional stack access
* ofpart parser:
- Support Linksys Northstar partitions
- Make symbol 'bcm4908_partitions_quirks' static
- Limit parsing of deprecated DT syntax
- Support BCM4908 fixed partitions
* Qcom parser:
- Incompatible with spi-nor 4k sectors
- Fix error condition
- Extend Qcom SMEM parser to SPI flash
CFI:
* Disable broken buffered writes for CFI chips within ID 0x2201
* Address a Coverity report for unused value
SPI NOR core:
* Add OTP support
* Fix module unload while an op in progress
* Add various cleanup patches
* Add Michael and Pratyush as designated reviewers in MAINTAINERS
SPI NOR controller drivers:
* intel-spi:
- Move platform data header to x86 subfolder
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND (APPLIED THEN REVERTED)
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmCBq3UACgkQJWrqGEe9
VoS9Xwf+I9W5WZS+WLYdlJ9RvuPDYVyZolZdsxIOOaOGuMAYSLJI/GjWJyHAFdwJ
qIPvr6qFnmKfUUaFZkln5Qk4QSfx+/t7+yj57e3lM9bSBEfTNToMI4AU8X6UAxa5
NHnsU8O8sohnk2UrP1qRtk3IezJ0FdzHbQAc82GQ1QY+IE0NwHg0ETjgESR5iEfq
PSnXb5Dgd637ENUlLsauSLbqFcD8sULvA3fJngxkQbBXDfv3KNZQhNsqw/l7NMY5
rROk8/jv7kgnYs8ObdkWO9SZ9QIiFSLk3vgbrTTNl8ozYpIMVbsrLmsnh7G34RNO
oWmbyOQdMDugaPYLJ9aTQmyI1qbKsA==
=zJPs
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull mtd updates from Miquel Raynal:
"MTD core:
- Handle possible -EPROBE_DEFER from parse_mtd_partitions()
- Constify buf in mtd_write_user_prot_reg()
- Constify name param in mtd_bdi_init
- Fix fall-through warnings for Clang
- Get rid of Big MTD Lock ouf of mtdchar
- Drop mtd_mutex usage from mtdchar_open()
- Don't lock when recursively deleting partitions
- Use module_mtd_blktrans() to register driver when relevant
- Parse MTD as NVMEM cells
- New OTP (one-time-programmable) erase ioctl
- Require write permissions for locking and badblock ioctls
- physmap:
- Fix error return code of physmap_flash_remove()
- physmap-bt1-rom: Fix unintentional stack access
- ofpart parser:
- Support Linksys Northstar partitions
- Make symbol 'bcm4908_partitions_quirks' static
- Limit parsing of deprecated DT syntax
- Support BCM4908 fixed partitions
- Qcom parser:
- Incompatible with spi-nor 4k sectors
- Fix error condition
- Extend Qcom SMEM parser to SPI flash
CFI:
- Disable broken buffered writes for CFI chips within ID 0x2201
- Address a Coverity report for unused value
SPI NOR core:
- Add OTP support
- Fix module unload while an op in progress
- Add various cleanup patches
- Add Michael and Pratyush as designated reviewers in MAINTAINERS
SPI NOR controller drivers:
- intel-spi:
- Move platform data header to x86 subfolder
NAND core:
- Fix error handling in nand_prog_page_op() (x2)
- Add a helper to retrieve the number of ECC bytes per step
- Add a helper to retrieve the number of ECC steps
- Let ECC engines advertize the exact number of steps
- ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
- ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
- Add support for secure regions in NAND memory
- Try not to use the ECC private structures
- Remove duplicate include in rawnand.h
- BBT:
- Skip bad blocks when searching for the BBT in NAND (APPLIED THEN REVERTED)
Raw NAND controller drivers:
- Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
- GPMI:
- Fix a double free in gpmi_nand_init
- Rockchip:
- Use flexible-array member instead of zero-length array
- Atmel:
- Update ecc_stats.corrected counter
- MXC:
- Remove unneeded of_match_ptr()
- R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
- Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
- FSMC:
- Fix error code in fsmc_nand_probe()
- OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
- Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
- gigadevice: Support GD5F1GQ5UExxG"
* tag 'mtd/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (89 commits)
Revert "mtd: rawnand: bbt: Skip bad blocks when searching for the BBT in NAND"
mtd: core: Constify buf in mtd_write_user_prot_reg()
Revert "mtd: spi-nor: macronix: Add support for mx25l51245g"
mtd: spi-nor: core: Fix an issue of releasing resources during read/write
mtd: cfi_cmdset_0002: remove redundant assignment to variable timeo
mtd: cfi_cmdset_0002: Disable buffered writes for AMD chip 0x2201
mtd: rawnand: qcom: Use dma_mapping_error() for error check
mtd: rawnand: gpmi: Fix a double free in gpmi_nand_init
mtd: rawnand: qcom: Add missing nand_cleanup() in error path
mtd: rawnand: Add support for secure regions in NAND memory
dt-bindings: mtd: Add a property to declare secure regions in NAND chips
dt-bindings: mtd: Convert Qcom NANDc binding to YAML
mtd: spi-nor: winbond: add OTP support to w25q32fw/jw
mtd: spi-nor: implement OTP support for Winbond and similar flashes
mtd: spi-nor: add OTP support
mtd: spi-nor: swp: Improve code around spi_nor_check_lock_status_sr()
mtd: spi-nor: Move Software Write Protection logic out of the core
mtd: rawnand: bbt: Skip bad blocks when searching for the BBT in NAND
include: linux: mtd: Remove duplicate include of nand.h
mtd: parsers: ofpart: support Linksys Northstar partitions
...
This reverts commit bd9c9fe2ad.
Since commit bd9c9fe2ad ("mtd: rawnand: bbt: Skip bad blocks when
searching for the BBT in NAND") the bad block table cannot be found
on a imx27-phytec-phycard-s-rdk board:
Bad block table not found for chip 0
Bad block table not found for chip 0
Revert it for now, until a better solution can be found.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210419140350.809853-1-festevam@gmail.com
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAmB1XbkACgkQJWrqGEe9
VoSWEAf6Al9DFds3w32oS8OB19pMb66jWLPvt//gIwV4tzSIsauQLqo4uBqDUPSt
EdUyehN6W792qsekmOReRc4ZcS2HpNPT5PRwYtsxPMkVmEL56tqs5ObNPGNOwvoH
9vyvsx7EhSu10a9JHjgJeNMVOBDMA8quXqHw0Y3cL2UBpuCYMm37ANF8okdvOmmr
Ykg1nCbfZL/dxFCGZ15ZuYuGQXea8PUryyxXUsWLDvsHg4KuhQKKtkarXmzz6XiD
tAyShtSrJFo/T0FniWc8jFbaq8WkU7XBg5f5qTTt5uT4JoXWGmjbIbXG0My91RKY
RO0b6z/odPOW1UHarlK8HrKW22YF9A==
=+fKJ
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
MTD core:
* Handle possible -EPROBE_DEFER from parse_mtd_partitions()
NAND core:
* Fix error handling in nand_prog_page_op() (x2)
* Add a helper to retrieve the number of ECC bytes per step
* Add a helper to retrieve the number of ECC steps
* Let ECC engines advertize the exact number of steps
* ECC Hamming:
- Populate the public nsteps field
- Use the public nsteps field
* ECC BCH:
- Populate the public nsteps field
- Use the public nsteps field
Raw NAND core:
* Add support for secure regions in NAND memory
* Try not to use the ECC private structures
* Remove duplicate include in rawnand.h
* BBT:
- Skip bad blocks when searching for the BBT in NAND
Raw NAND controller drivers:
* Qcom:
- Convert bindings to YAML
- Use dma_mapping_error() for error check
- Add missing nand_cleanup() in error path
- Return actual error code instead of -ENODEV
- Update last code word register
- Add helper to configure location register
- Rename parameter name in macro
- Add helper to check last code word
- Convert nandc to chip in Read/Write helper
- Update register macro name for 0x2c offset
* GPMI:
- Fix a double free in gpmi_nand_init
* Rockchip:
- Use flexible-array member instead of zero-length array
* Atmel:
- Update ecc_stats.corrected counter
* MXC:
- Remove unneeded of_match_ptr()
* R852:
- replace spin_lock_irqsave by spin_lock in hard IRQ
* Brcmnand:
- Move to polling in pio mode on oops write
- Read/write oob during EDU transfer
- Fix OOB R/W with Hamming ECC
* FSMC:
- Fix error code in fsmc_nand_probe()
* OMAP:
- Use ECC information from the generic structures
SPI-NAND core:
* Add missing MODULE_DEVICE_TABLE()
SPI-NAND drivers:
* gigadevice: Support GD5F1GQ5UExxG
If the callee gpmi_alloc_dma_buffer() failed to alloc memory for
this->raw_buffer, gpmi_free_dma_buffer() will be called to free
this->auxiliary_virt. But this->auxiliary_virt is still a non-NULL
and valid ptr.
Then gpmi_alloc_dma_buffer() returns err and gpmi_free_dma_buffer()
is called again to free this->auxiliary_virt in err_out. This causes
a double free.
As gpmi_free_dma_buffer() has already called in gpmi_alloc_dma_buffer's
error path, so it should return err directly instead of releasing the dma
buffer again.
Fixes: 4d02423e9a ("mtd: nand: gpmi: Fix gpmi_nand_init() error path")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210403060905.5251-1-lyl2019@mail.ustc.edu.cn
On a typical end product, a vendor may choose to secure some regions in
the NAND memory which are supposed to stay intact between FW upgrades.
The access to those regions will be blocked by a secure element like
Trustzone. So the normal world software like Linux kernel should not
touch these regions (including reading).
The regions are declared using a NAND chip DT property,
"secure-regions". So let's make use of this property in the raw NAND
core and skip access to the secure regions present in a system.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210402150128.29128-4-manivannan.sadhasivam@linaro.org
The blocks containing the bad block table can become bad as well. So
make sure to skip any blocks that are marked bad when searching for the
bad block table.
Otherwise in very rare cases where two BBT blocks wear out it might
happen that an obsolete BBT is used instead of a newer available
version.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210325102337.481172-1-s.riedmueller@phytec.de
Suppresses the following coccinelle warning:
drivers/mtd/nand/raw/rockchip-nand-controller.c:162:4-8: WARNING use flexible-array member instead
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210323131137.45552-1-zou_wei@huawei.com
This fixes NAND_OP_WAITRDY_INSTR operation in the driver. Without this
change the driver waits till the system is busy, but we should wait till
the busy flag is cleared. The readl_poll_timeout() function gets a break
condition, not a wait condition.
In addition fix the timeout. The timeout_ms is given in ms, but the
readl_poll_timeout() function takes the timeout in us. Multiple the
given timeout by 1000 to convert it.
Without this change, the driver does not work at all, it doesn't even
identify the NAND chip.
Fixes: 5197360f9e ("mtd: rawnand: mtk: Convert the driver to exec_op()")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210309000107.1368404-1-hauke@hauke-m.de
In qcom_probe_nand_devices() function, the error code returned by
qcom_nand_host_init_and_register() is converted to -ENODEV in the case
of failure. This poses issue if -EPROBE_DEFER is returned when the
dependency is not available for a component like parser.
So let's restructure the error handling logic a bit and return the
actual error code in case of qcom_nand_host_init_and_register() failure.
Fixes: c76b78d8ec ("mtd: nand: Qualcomm NAND controller driver")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Hamming ECC doesn't cover the OOB data, so reading or writing OOB shall
always be done without ECC enabled.
This is a problem when adding JFFS2 cleanmarkers to erased blocks. If JFFS2
clenmarkers are added to the OOB with ECC enabled, OOB bytes will be changed
from ff ff ff to 00 00 00, reporting incorrect ECC errors.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210224080210.23686-1-noltari@gmail.com
From QPIC v2 onwards a new register got added to read last
code word.Add support for this READ_LOCATION_LAST_CW_n
register.
In the case of QPIC v2, codewords 0, 1 and 2 will be accessed
through READ_LOCATION_n, while codeword 3 will be accessed
through READ_LOCATION_LAST_CW_n.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-5-git-send-email-mdalam@codeaurora.org
Create a nandc_set_read_loc() helper to abstract the
configuration of the location register.
QPIC v2 onwards features a separate location register
for the last codeword, so introducing this extra helper
which will simplify the addition of QPIC v2 support.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-4-git-send-email-mdalam@codeaurora.org
Rename the parameters of the nandc_set_read_loc() macro
to avoid the confusion between is_last_read_loc which
is last location in a read code word and last_cw which
is last code word of a page data.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-3-git-send-email-mdalam@codeaurora.org
This change will convert nandc to chip in Read/Write helper, this
change is needed because if we wnated to access number of steps
in Read/Write helper then we need to get the chip->ecc.steps,
currentlly its not possible.After this change we can directly
acces chip->ecc.steps in Read/Write helper.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1614109141-7531-1-git-send-email-mdalam@codeaurora.org
If dma_request_channel() fails then the probe fails and it should
return a negative error code, but currently it returns success.
fixes: 4774fb0a48 ("mtd: nand/fsmc: Add DMA support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/YCqaOZ83OvPOzLwh@mwanda
On success nand_exec_prog_page_op() returns the NAND status byte, but on
failure it returns a negative error code. nand_prog_page_op() interprets
the return value as NAND status byte without error checking. This means
a failure in nand_exec_prog_page_op() can go through unnoticed.
The straight forward fix would be to add the missing error checking. To
clean the code a bit we can move the nand status check to
nand_prog_page_op(). This way we can get rid of the overloaded return
value from nand_exec_prog_page_op() and return a plain error code which
is less error prone.
nand_exec_prog_page_op() is only called from one other place and in this
call the 'prog' parameter is false in which case the nand status check
is skipped, so it's correct to not add the NAND status check there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210205142725.13225-2-s.hauer@pengutronix.de
On success chip->legacy.waitfunc() returns the NAND status byte, but on
failure it returns a negative error code. This was never tested for and
instead the return value was interpreted as NAND status without error
checking. Add the missing error check.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210205142725.13225-1-s.hauer@pengutronix.de
This change will remove unused register name macro NAND_DEV1_ECC_CFG.
Since this register was only available in QPIC version 1.4.20 ipq40xx
and it was not used. In QPIC version 1.5 on wards this register got
removed.In QPIC version 2.0 0x2c offset is updated with register
NAND_AUTO_STATUS_EN So adding this register macro NAND_AUTO_STATUS_EN
with offset 0x2c.
Signed-off-by: Md Sadre Alam <mdalam@codeaurora.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1612037236-7954-1-git-send-email-mdalam@codeaurora.org
As part of a previous fix, we imported the BCH internal structure in
order to get information about the BCH engine configuration.
It is best not to access private structure so instead, a small rework
has been done to export more information from the ECC engines. Now,
let's use these.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-8-miquel.raynal@bootlin.com
Most of the time, there is no need to use the software ECC Hamming and
BCH algorithms private context to know their configuration. All the
data has been stored by their ->init_ctx() hook in the generic NAND
ECC engine structure, so use this one when possible.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd Torpedo
Link: https://lore.kernel.org/linux-mtd/20210127203020.9574-7-miquel.raynal@bootlin.com
* Initial support for BCM4908 partitions
Raw NAND controller drivers:
* Intel: Fix an error handling path in 'ebu_dma_start()'
* Tango: Remove the driver
* Marvell: Convert comma to semicolon
* MXC: Convert comma to semicolon
* Qcom: Add support for Qcom SMEM parser
Related MTD changes:
* parsers: Add Qcom SMEM parser
SPI NOR core changes:
* Add non-uniform erase fixes.
* Add Global Block Unlock command. It is defined by few flash
vendors, and it is used for now just by sst.
SPI NOR controller drivers changes:
* intel-spi: Add support for Intel Alder Lake-P SPI serial flash.
* hisi-sfc: Put child node np on error path.
-----BEGIN PGP SIGNATURE-----
iQJKBAABCAA0FiEEdgfidid8lnn52cLTZvlZhesYu8EFAmAyuDgWHHJpY2hhcmRA
c2lnbWEtc3Rhci5hdAAKCRBm+VmF6xi7wf/WEACWtDmQVXZPoKijrYZBWXLv3dC2
JEUT3QKwnDVf9QOLUjq5MdCxN/z3IqAjx1htVrR3DFExjgFkMbmxOMQxHp+d4BiP
hZBIaC7UFocsgXY5iZ7OyZBoZoE8GQwpIiz8KMoXN1sqB6vrfn3NenbbDldsJgVx
5jAWNarHm0ndHYtBEVwhOC9ogp1b8GR6/W8iAv2jt3Ap06FajSlaf2SOknxD1rY5
pSosVxXFdWatWI88ZAj+v68o+yAj+Yd3wTunA1pPHPr9jlHNJ0JlpIlWH4XU0iir
BBTFdF9v8/id7Lo+eFw05rfIQ/eMDlD93B0qHKcyIUjJOs1rj2JshFM/QbH64Mjv
zDLfqacRZQgHNZJg8AfdCPGhjxwl60BTrXiASG5TYsvavvyEx/L1mtdJ2ZI+tizU
kFNzdpdgEroZtTKMiA0scTRqciB6/IA7PmLpfhBf0Zzi+EENIB+bBwi+EH4aYmYC
PYl2/wABNA+JkSypT+UJKcYnFt3FYRtTq5O4tUyLcwRzbHuYUqZTMi/QeD01ltvN
4B5VbsOtAAfJSOMWGc7qbf34Hs7kED0TrfKbmtaZf580eso7+zpxdtxVnm5iBx7u
V5M2TDOq7/81sXgnvc2i8qbOWtVI9GcRWfre+PgheMn97Wd4VvInfXawwShI1TGU
PlCelptKmuc035eRBQ==
=uQQ1
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Richard Weinberger:
"MTD core changes:
- Initial support for BCM4908 partitions
Raw NAND controller drivers:
- Intel: Fix an error handling path in 'ebu_dma_start()'
- Tango: Remove the driver
- Marvell: Convert comma to semicolon
- MXC: Convert comma to semicolon
- Qcom: Add support for Qcom SMEM parser
Related MTD changes:
- parsers: Add Qcom SMEM parser
SPI NOR core changes:
- Add non-uniform erase fixes.
- Add Global Block Unlock command. It is defined by few flash
vendors, and it is used for now just by sst.
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Alder Lake-P SPI serial flash.
- hisi-sfc: Put child node np on error path"
* tag 'mtd/for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (23 commits)
dt-bindings: mtd: add binding for BCM4908 partitions
dt-bindings: mtd: move partition binding to its own file
mtd: spi-nor: sst: Add support for Global Unlock on sst26vf
mtd: spi-nor: Add Global Block Unlock command
mtd: spi-nor: core: Add erase size check for erase command initialization
mtd: spi-nor: core: Fix erase type discovery for overlaid region
mtd: spi-nor: sfdp: Fix last erase region marking
mtd: spi-nor: sfdp: Fix wrong erase type bitmask for overlaid region
mtd: rawnand: intel: Fix an error handling path in 'ebu_dma_start()'
mtd: rawnand: tango: Remove the driver
mtd: rawnand: marvell: convert comma to semicolon
mtd: st_spi_fsm: convert comma to semicolon
mtd: convert comma to semicolon
mtd: parsers: afs: Fix freeing the part name memory in failure
mtd: parser: imagetag: fix error codes in bcm963xx_parse_imagetag_partitions()
mtd: phram: use div_u64_rem to stop overwrite len in phram_setup
mtd: remove redundant assignment to pointer eb
mtd: spi-nor: hisi-sfc: Put child node np on error path
mtd: spi-nor: intel-spi: Add support for Intel Alder Lake-P SPI serial flash
mtd: rawnand: qcom: Add support for Qcom SMEM parser
...
There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use [1], and
received confirmation about six ARM platforms and the TI C6x architecture
that have all reached the end of their life upstream, with no known
users remaining:
- efm32 -- added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell -- added in 2011, abandoned after 2012 acquisition
- prima2 -- added in 20111, no notable changes since 2015
- tango -- added in 2015, sporadic changes until 2017, but abandoned
- u300 -- added in 2009, no notable changes since 2013
- zx --added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x -- added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users
that plan to contribute them in the future, in other cases the code
is complete and works reliably.
[1] https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=pf3b
-----END PGP SIGNATURE-----
Merge tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform removals from Arnd Bergmann:
"There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use, and
received confirmation about six ARM platforms and the TI C6x
architecture that have all reached the end of their life upstream,
with no known users remaining:
- efm32 - added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell - added in 2011, abandoned after 2012 acquisition
- prima2 - added in 20111, no notable changes since 2015
- tango - added in 2015, sporadic changes until 2017, but abandoned
- u300 - added in 2009, no notable changes since 2013
- zx - added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x - added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users that
plan to contribute them in the future, in other cases the code is
complete and works reliably"
Link: https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
* tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: remove u300 platform
ARM: remove tango platform
ARM: remove zte zx platform
ARM: remove sirf prima2/atlas platforms
c6x: remove architecture
MAINTAINERS: Remove deleted platform efm32
ARM: drop efm32 platform
ARM: Remove PicoXcell platform support
ARM: dts: Remove PicoXcell platforms
If 'dmaengine_prep_slave_single()' fails, we must undo a previous
'dma_map_single()' call, as already done in all the other error handling
paths of this function.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210124073955.728797-1-christophe.jaillet@wanadoo.fr
The OMAP driver may leverage software BCH logic to locate errors while
using its own hardware to detect the presence of errors. This is
achieved with a "mixed" mode which initializes manually the software
BCH internal logic while providing its own OOB layout.
The issue here comes from the fact that the BCH driver has been
updated to only use generic NAND objects, and no longer depend on raw
NAND structures as it is usable from SPI-NAND as well. However, at the
end of the BCH context initialization, the driver checks the validity
of the OOB layout. At this stage, the raw NAND fields have not been
populated yet while being used by the layout helpers, leading to an
invalid layout.
The chosen solution here is to include the BCH structure definition
and to refer to the BCH fields directly (de-referenced as a const
pointer here) to know as early as possible the number of steps and ECC
bytes which have been chosen.
Note: I don't know which commit exactly triggered the error, but the
entire migration to a generic BCH driver got merged in one go, so this
should not be a problem for stable backports.
Reported-by: Adam Ford <aford173@gmail.com>
Fixes: 80fe603160 ("mtd: nand: ecc-bch: Stop using raw NAND structures")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit-28.dts
Link: https://lore.kernel.org/linux-mtd/20210119155510.5655-1-miquel.raynal@bootlin.com
The Ericsson U300 platform was one of two ARM929 based SoC platforms for
mobile phones in ST-Ericsson after the merger of Ericsson with ST-NXP
into ST-Ericsson, the other one being the ST Nomadik.
The platform was not widely adopted in Linux based systems and was
replaced with the far superior ST-Ericsson U8500 in 2011, but Linus
Walleij kept maintaining the code for the whole time.
Linus continues to use the Nomadik machine, but decided to drop
u300 from the kernel as part of this year's spring cleaning.
Thanks for having maintained it all these years.
Cc: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/lkml/CACRpkdbJkiHR9FSfJTH_5d_qRU1__dRXHM1TL40iqNRKbGQfrQ@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Move the check for mtd->name after the mtd variable has actually been
initialized.
While here, also drop the NULL assignment to the mtd variable as it's
overwritten later on anyways and the NULL value is never read.
Fixes: 0b1039f016 ("mtd: rawnand: Add NAND controller support on Intel LGM SoC")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210106140943.98072-1-martin.blumenstingl@googlemail.com
I have been fooled by the logic picking the right ECC engine which is
spread across two functions: *init_module() and *_attach(). I thought
this driver was not impacted by the recent changes around the ECC
engines DT parsing logic but in fact it is.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210104093057.31178-1-miquel.raynal@bootlin.com
Re-add the multiply by 8 to "step * eccsize" to correct the destination bit offset
when extracting the data payload in gpmi_ecc_read_page_raw().
Fixes: e5e5631cc8 ("mtd: rawnand: gpmi: Use nand_extract_bits()")
Cc: stable@vger.kernel.org
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201221100013.2715675-1-sean@geanix.com
* Fix refcounting for unpartitioned MTDs
* Fix misspelled function parameter 'section'
* Remove unneeded break
* cmdline parser: Fix parsing of part-names with colons
* mtdpart: Fix misdocumented function parameter 'mtd'
MTD devices:
* phram:
- Allow the user to set the erase page size
- File headers are not good candidates for kernel-doc
* physmap-bt1-rom: Fix __iomem addrspace removal warning
* plat-ram: correctly free memory on error path in platram_probe()
* powernv_flash: Add function names to headers and fix 'dev'
* docg3: Fix kernel-doc 'bad line' and 'excessive doc' issues
UBI cleanup fixes:
* gluebi: Fix misnamed function parameter documentation
* wl: Fix a couple of kernel-doc issues
* eba: Fix a couple of misdocumentation issues
* kapi: Correct documentation for 'ubi_leb_read_sg's 'sgl' parameter
* Document 'ubi_num' in struct mtd_dev_param
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* Arasan: Document 'anfc_op's 'buf' member
* AU1550: Ensure the presence of the right includes
* Brcmnand: Demote non-conformant kernel-doc headers
* Cafe: Remove superfluous param doc and add another
* Davinci: Do not use extra dereferencing
* Diskonchip: Marking unused variables as __always_unused
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Omap:
- Fix a bunch of kernel-doc misdemeanours
- Finish ELM half populated function header, demote empty ones
* s3c2410: Add documentation for 2 missing struct members
* Sunxi: Document 'sunxi_nfc's 'caps' member
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
ONENAND:
* bbt: Fix expected kernel-doc formatting
* Fix some kernel-doc misdemeanours
* Fix expected kernel-doc formatting
* Use mtd->oops_panic_write as condition
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
* Toshiba: Demote non-conformant kernel-doc header
SPI-NOR core:
* Initial support for stateful Octal DTR mode using volatile settings
* Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
* Support for Cypress Semper flash
* Support to specify ECC block size of SPI NOR flashes
* Fixes to avoid clearing of non-volatile Block Protection bits at
probe
* hisi-sfc: Demote non-conformant kernel-doc
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl/aS1sACgkQJWrqGEe9
VoTOqQgAiu3XfM7iHvFDiz0SVL+RFzqi2jnwXHgGDATTq+vOPwAMaqnqF6xZZZLA
BIKsLwVRJnZ9Vu6Xl2vAPaVob+QKbsvvP9kkk9H/dZJ6IW4XsWFqYotPSQQ/6ZBO
2bmw9nQ0ZcksyUkdASGHuYlW/H5DAtQNQuQxGF5ywlZMxTEnD0wxUD5tccf1o3xk
UYvQsQ0MNMriWCxbcdUXUmDOE9DuPdDysuLDPJs0WLnlNGgwZ/mnLvSRm6wm4nRT
Y/pB6VcTMMEYAsujdf89LjCHlfCQuH5Zls9pxic8GkHjOcEqUeMLLXkkbQ1+61AO
93QsOhKAsju49/aHpbpvwu5SEmLojA==
=1fie
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core:
- Fix refcounting for unpartitioned MTDs
- Fix misspelled function parameter 'section'
- Remove unneeded break
- cmdline parser: Fix parsing of part-names with colons
- mtdpart: Fix misdocumented function parameter 'mtd'
MTD devices:
- phram:
- Allow the user to set the erase page size
- File headers are not good candidates for kernel-doc
- physmap-bt1-rom: Fix __iomem addrspace removal warning
- plat-ram: correctly free memory on error path in platram_probe()
- powernv_flash: Add function names to headers and fix 'dev'
- docg3: Fix kernel-doc 'bad line' and 'excessive doc' issues
UBI cleanup fixes:
- gluebi: Fix misnamed function parameter documentation
- wl: Fix a couple of kernel-doc issues
- eba: Fix a couple of misdocumentation issues
- kapi: Correct documentation for 'ubi_leb_read_sg's 'sgl' parameter
- Document 'ubi_num' in struct mtd_dev_param
Generic NAND core ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the generic
NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
- Geting rid of the chip->ecc.priv entry.
- Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
- Arasan: Document 'anfc_op's 'buf' member
- AU1550: Ensure the presence of the right includes
- Brcmnand: Demote non-conformant kernel-doc headers
- Cafe: Remove superfluous param doc and add another
- Davinci: Do not use extra dereferencing
- Diskonchip: Marking unused variables as __always_unused
- GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
- Ingenic: remove redundant get_device() in ingenic_ecc_get()
- Intel LGM: New NAND controller driver
- Marvell: Drop useless line
- Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
- mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
- Omap:
- Fix a bunch of kernel-doc misdemeanours
- Finish ELM half populated function header, demote empty ones
- s3c2410: Add documentation for 2 missing struct members
- Sunxi: Document 'sunxi_nfc's 'caps' member
- Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
- Rockchip: New NAND controller driver for RK3308, RK2928 and others
- Sunxi: Add MDMA support
ONENAND:
- bbt: Fix expected kernel-doc formatting
- Fix some kernel-doc misdemeanours
- Fix expected kernel-doc formatting
- Use mtd->oops_panic_write as condition
SPI-NAND core:
- Creation of a SPI-NAND on-die ECC engine
- Move ECC related definitions earlier in the driver
- Fix typo in comment
- Fill a default ECC provider/algorithm
- Remove outdated comment
- Fix OOB read
- Allow the case where there is no ECC engine
- Use the external ECC engine logic
SPI-NAND chip drivers:
- Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
- Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
- Toshiba: Demote non-conformant kernel-doc header
SPI-NOR core:
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at
probe
- hisi-sfc: Demote non-conformant kernel-doc"
* tag 'mtd/for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (120 commits)
mtd: spinand: macronix: Add support for MX35LFxG24AD
mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others
dt-bindings: mtd: Describe Rockchip RK3xxx NAND flash controller
mtd: rawnand: gpmi: Use a single line for of_device_id
mtd: rawnand: gpmi: Fix the random DMA timeout issue
mtd: rawnand: gpmi: Fix the driver only sense CS0 R/B issue
mtd: rawnand: qcom: Add NAND controller support for SDX55
dt-bindings: qcom_nandc: Add SDX55 QPIC NAND documentation
mtd: rawnand: mxc: Use a single line for of_device_id
mtd: rawnand: mxc: Use device_get_match_data()
mtd: rawnand: meson: Fix a resource leak in init
mtd: rawnand: gpmi: Use of_device_get_match_data()
mtd: rawnand: Add NAND controller support on Intel LGM SoC
dt-bindings: mtd: Add Nand Flash Controller support for Intel LGM SoC
mtd: spinand: micron: Add support for MT29F2G01AAAED
mtd: spinand: micron: Use more specific names
mtd: rawnand: gpmi: fix reference count leak in gpmi ops
dt-bindings: mtd: gpmi-nand: Fix matching of clocks on different SoCs
mtd: spinand: macronix: Add support for MX35LFxGE4AD
mtd: plat-ram: correctly free memory on error path in platram_probe()
...
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEEyRC2zAhGcGjrhiNExEYeRXyRFuMFAl/XAWAQHHZpZ25lc2hy
QHRpLmNvbQAKCRDERh5FfJEW40rIB/sG1foD0j1iImcTfjlVW4I21HabniykUPBw
GTUlsHoDEEjhY3jEjdYx+l8HHdcqadmedR27DO91l+2ieR7uVoIn2lTADbxnWrgl
DsE6aQLf7KWn340UxEUtihNaa14Zr45GcpYdqs0tjMClRHxM0udwd6qIFHGCi9AC
MOA6kFJewLdCqIRYwBoo1VD4iYQA0RMR463KLvIdrS1bGpkaB3ihxBZb3QgR2ILD
mG9sZClCzeivjNkuiCrJrkWZgAvYTM5DZugBd9+X85Qtq4921zQS5QfZLA9UjnFh
7ChrsTJQFz6CByt6oAH4jCtc0T1hJRL9o1FlbIsAO6gP5mRxKFUV
=bIwk
-----END PGP SIGNATURE-----
mergetag object ee4e0eafa4
type commit
tag nand/for-5.11
tagger Miquel Raynal <miquel.raynal@bootlin.com> 1608042580 +0100
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl/Yz80ACgkQJWrqGEe9
VoTGxAf8CqJ1nc3kuhHasjyIQ+cCK6TkqP3KciGXOlmLJXFkhvk9ge/9Q0qttevh
gA/y5wQWn4L7o5nssslKNZ9UXCv7Ksopukx8gFjXHXM0CeukJ7Px3Phlu27WLiOn
qgmSX3xTVV8wdcVXxS+iNpsu3v5G/H4rZLb2V0bH8+tvalAEje8k6AHP4XLLrjIS
mcjkhLn46ttT7WvxmVmlUN+ghrmFRT5DnhgaD7JdE9beaJv8yZ8MLoz5oFD56Z9S
f7qYugVW0ClOK/YvuPRRCiJcMg3siHxm8XtqQTA2spq/LY6hBEykNFlxbQ/23DXa
1kCUi2L1ld+JOe9YgK+OskoIf+Fywg==
=mqSb
-----END PGP SIGNATURE-----
Merge tags 'spi-nor/for-5.11' and 'nand/for-5.11' into mtd/next
SPI NOR core changes:
- Initial support for stateful Octal DTR mode using volatile settings
- Preliminary support for JEDEC 251 (xSPI) and JEDEC 216D standards
- Support for Cypress Semper flash
- Support to specify ECC block size of SPI NOR flashes
- Fixes to avoid clearing of non-volatile Block Protection bits at probe
Generic NAND core:
* ECC management:
- Add an I/O request tweaking mechanism
- Entire rework of the software BCH ECC driver, creation of a real
ECC engine, getting rid of raw NAND structures, migration to more
generic prototypes, misc fixes and style cleanup. Moved now to the
Generic NAND layer.
- Entire rework of the software Hamming ECC driver, creation of a
real ECC engine, getting rid of raw NAND structures, misc renames,
comment updates, cleanup, and style fixes. Moved now to the
generic NAND layer.
- Necessary plumbing at the NAND level to retrieve generic NAND ECC
engines (softwares and on-die).
- Update of the bindings.
Raw NAND core:
* Geting rid of the chip->ecc.priv entry.
* Fix miscellaneous typos in kernel-doc
Raw NAND controller drivers:
* AU1550: Ensure the presence of the right includes
* Davinci: Do not use extra dereferencing
* GPMI:
- Fix the driver only sense CS0 R/B issue
- Fix the random DMA timeout issue
- Use a single line for of_device_id
- Use of_device_get_match_data()
- Fix reference count leak in gpmi ops
- Cleanup makefile
- Fix binding matching of clocks on different SoCs
* Ingenic: remove redundant get_device() in ingenic_ecc_get()
* Intel LGM: New NAND controller driver
* Marvell: Drop useless line
* Meson:
- Fix a resource leak in init
- Fix meson_nfc_dma_buffer_release() arguments
* mxc:
- Use device_get_match_data()
- Use a single line for of_device_id
- Remove platform data support
* Qcom:
- Add support for SDX55
- Support for IPQ6018 QPIC NAND controller
- Fix DMA sync on FLASH_STATUS register read
* Rockchip: New NAND controller driver for RK3308, RK2928 and others
* Sunxi: Add MDMA support
SPI-NAND core:
* Creation of a SPI-NAND on-die ECC engine
* Move ECC related definitions earlier in the driver
* Fix typo in comment
* Fill a default ECC provider/algorithm
* Remove outdated comment
* Fix OOB read
* Allow the case where there is no ECC engine
* Use the external ECC engine logic
SPI-NAND chip drivers:
* Micron:
- Add support for MT29F2G01AAAED
- Use more specific names
* Macronix:
- Add support for MX35LFxG24AD
- Add support for MX35LFxGE4AD
Others:
* onenand: Use mtd->oops_panic_write as condition
* plat-ram: correctly free memory on error path in platram_probe()
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: d525914b5b ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-10-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: b36bf0a0fe ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-9-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: 612e048e6a ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-8-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: 8fc6f1f042 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-7-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Fixes: 553508cec2 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-6-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: 6dd09f775b ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-5-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: f6341f6448 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-4-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: dbffc8ccdf ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-3-miquel.raynal@bootlin.com
Originally, commit d7157ff49a ("mtd: rawnand: Use the ECC framework
user input parsing bits") kind of broke the logic around the
initialization of several ECC engines.
Unfortunately, the fix (which indeed moved the ECC initialization to
the right place) did not take into account the fact that a different
ECC algorithm could have been used thanks to a DT property,
considering the "Hamming" algorithm entry a configuration while it was
only a default.
Add the necessary logic to be sure Hamming keeps being only a default.
Fixes: 59d9347332 ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201203190340.15522-2-miquel.raynal@bootlin.com
This driver supports Rockchip NFC (NAND Flash Controller) found on RK3308,
RK2928, RKPX30, RV1108 and other SOCs. The driver has been tested using
8-bit NAND interface on the ARM based RK3308 platform.
Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.
Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)
Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to use
the BBT(bad block table).
Suggested-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201210002134.5686-3-yifeng.zhao@rock-chips.com
Set the GPMI CTRL1 GANGED_RDYBUSY bit so driver can sense the R/B signal
from all CS.
For the NAND chip MT29F64G08AFAAAWP, only the first chip detected
without the patch.
[ 3.764118] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770613] nand: Micron MT29F64G08AFAAAWP
[ 3.774752] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.786421] Bad block table found at page 524160, version 0x01
[ 3.792730] Bad block table found at page 524032, version 0x01
After applying the patch
[ 3.764445] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x68
[ 3.770941] nand: Micron MT29F64G08AFAAAWP
[ 3.775080] nand: 4096 MiB, SLC, erase size: 1024 KiB, page size: 8192, OOB size: 448
[ 3.784390] nand: 2 chips detected
[ 3.790900] Bad block table found at page 524160, version 0x01
[ 3.796776] Bad block table found at page 1048448, version 0x01
Signed-off-by: Han Xu <han.xu@nxp.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201209035104.22679-2-han.xu@nxp.com
SDX55 uses QPIC version 2.0.0 IP for the NAND controller support.
In this version, DEV_CMD_* registers are moved to operational state,
hence CPU access in BAM mode is restricted. So, skip accessing these
registers and also use a different config for reading ONFI parameters.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126085705.48399-3-manivannan.sadhasivam@linaro.org
Call clk_disable_unprepare(nfc->phase_rx) if the clk_set_rate() function
fails to avoid a resource leak.
Fixes: 8fae856c53 ("mtd: rawnand: meson: add support for Amlogic NAND flash controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/X8ikVCnUsfTpffFB@mwanda
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.
Use of_device_get_match_data() to simplify the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201126030946.2058-1-festevam@gmail.com
This patch adds the new IP of Nand Flash Controller(NFC) support
on Intel's Lightning Mountain(LGM) SoC.
DMA is used for burst data transfer operation, also DMA HW supports
aligned 32bit memory address and aligned data access by default.
DMA burst of 8 supported. Data register used to support the read/write
operation from/to device.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110012333.18647-3-vadivel.muruganx.ramuthevar@linux.intel.com
pm_runtime_get_sync() will increment pm usage at first and it
will resume the device later. If runtime of the device has
error or device is in inaccessible state(or other error state),
resume operation will fail. If we do not call put operation to
decrease the reference, it will result in reference leak in
the two functions(gpmi_init and gpmi_nfc_exec_op). Moreover,
this device cannot enter the idle state and always stay busy or
other non-idle state later. So we fixed it through adding
pm_runtime_put_noidle.
Fixes: 5bc6bb603b ("mtd: rawnand: gpmi: Fix suspend/resume problem")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201107110552.1568742-1-zhangqilong3@huawei.com
struct mtd_info has a flag oops_panic_write which is set when the write
operation is issued via the panic_write() callback. That allows controller
drivers to distinguish the panic write from a regular write.
Replace the open coded 'in_interrupt() | oops_in_progress' checks with a
check for that flag. in_interrupt() is an unrealiable indicator anyway as
it covers all sorts of atomic contexts not only hard and soft interrupt
service routines.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: linux-mtd@lists.infradead.org
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113141422.2214771-1-bigeasy@linutronix.de
While working a bit on this driver I dropped the platform includes and
commented a few lines just to verify the correctness of my changes. It
appeared the following:
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_waitrdy’:
drivers/mtd/nand/raw/au1550nd.c:130:3: error: implicit declaration of function ‘usleep_range’ [-Werror=implicit-function-declaration]
usleep_range(10, 100);
^~~~~~~~~~~~
drivers/mtd/nand/raw/au1550nd.c: In function ‘au1550nd_exec_instr’:
drivers/mtd/nand/raw/au1550nd.c:188:3: error: implicit declaration of function ‘ndelay’ [-Werror=implicit-function-declaration]
ndelay(instr->delay_ns);
^~~~~~
I think the delay.h header should be included in this file and not
come from one of its platform includes, so let's add it here.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113124021.32675-1-miquel.raynal@bootlin.com
i.MX is a devicetree-only platform now and the existing platform data
support in this driver was only useful for old non-devicetree platforms.
Get rid of the platform data support since it is no longer used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201110121908.19400-1-festevam@gmail.com
of_find_device_by_node() already takes a reference to the device, and
ingenic_ecc_release() will drop the reference. So, the get_device() in
ingenic_ecc_get() is redundand.
Fixes: 15de8c6efd0e("mtd: rawnand: ingenic: Separate top-level and SoC specific code")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201031105439.2304211-1-yukuai3@huawei.com
This patch enables NAND MDMA (MBUS DMA) mode for
the Allwinner SoCs A23/A33/H3.
The DMA transfer method gets sets now to MBUS DMA as default for
the sun8i-a23-nand-controller (till now DMA transfer was executed
via the shared DMA engine).
The main advantage is more bandwidth for the users of the shared DMA
engine and also that the MBUS DMA setup requires less configuration
effort. For example you don't need to define a dedicated DMA channel
in the device-tree any more.
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Manuel Dipolt <manuel.dipolt@robart.cc>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/154840787.280672.1602517282173.JavaMail.zimbra@robart.cc
After each codeword NAND_FLASH_STATUS is read for possible operational
failures. But there is no DMA sync for CPU operation before reading it
and this leads to incorrect or older copy of DMA buffer in reg_read_buf.
This patch adds the DMA sync on reg_read_buf for CPU before reading it.
Fixes: 5bc36b2bf6 ("mtd: rawnand: qcom: check for operation errors in case of raw read")
Cc: stable@vger.kernel.org
Signed-off-by: Praveenkumar I <ipkumar@codeaurora.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1602230872-25616-1-git-send-email-ipkumar@codeaurora.org
This code is meant to be reused by the SPI-NAND core. Now that the
driver has been cleaned and reorganized, use a generic ECC engine
object to store the driver's data instead of accessing members of the
nand_chip structure. This means adding proper init/cleanup helpers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-17-miquel.raynal@bootlin.com
Prefix by ecc_sw_hamming_ the functions which should be internal only
but are exported for "raw" operations.
Prefix by nand_ecc_sw_hamming_ the other functions which will be used
in the context of the declaration of an Hamming proper ECC engine
object.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-16-miquel.raynal@bootlin.com
nand_ecc_ctrl embeds a private pointer which only has a meaning in the
sunxi driver. This structure will soon be deprecated, but as this
field is actually not needed, let's just drop it.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-11-miquel.raynal@bootlin.com
Let's continue introducing the generic ECC engine abstraction in the
NAND subsystem by instantiating a first ECC engine: the software
BCH one.
While at it, make a very tidy ecc_sw_bch_init() function and move all
the sanity checks and user input management in
nand_ecc_sw_bch_init_ctx(). This second helper will be called from the
raw RAND core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-10-miquel.raynal@bootlin.com
This code is meant to be reused by the SPI-NAND core. Now that the
driver has been cleaned and reorganized, use a generic ECC engine
object to store the driver's data instead of accessing members of the
nand_chip structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-9-miquel.raynal@bootlin.com
These functions must be usable by the main NAND core, so their names
must be technology-agnostic as well as the parameters. Hence, we pass
a generic nand_device instead of a raw nand_chip structure.
As it seems that changing the raw NAND functions to always pass a
generic NAND device is a lost of time, we prefer to create dedicated
raw NAND wrappers that will be useful in the near future to do the
translation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-8-miquel.raynal@bootlin.com
The NAND BCH control structure has nothing to do outside of this
driver, all users of the nand_bch_init/free() functions just save it
to chip->ecc.priv so do it in this driver directly and return a
regular error code instead.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200929230124.31491-5-miquel.raynal@bootlin.com
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/arasan-nand-controller.c:133: warning: Function parameter or member 'buf' not described in 'anfc_op'
Cc: Naga Sureshkumar Relli <nagasure@xilinx.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Choudary Kalluri <punnaia@xilinx.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-22-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/sunxi_nand.c:250: warning: Function parameter or member 'caps' not described in 'sunxi_nfc'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Boris BREZILLON <b.brezillon.dev@gmail.com>
Cc: Qiang Yu <yuq825@gmail.com>
Cc: Dmitriy B <rzk333@gmail.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-21-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/omap2.c:191: warning: Function parameter or member 'info' not described in 'omap_prefetch_enable'
drivers/mtd/nand/raw/omap2.c:221: warning: Function parameter or member 'cs' not described in 'omap_prefetch_reset'
drivers/mtd/nand/raw/omap2.c:221: warning: Function parameter or member 'info' not described in 'omap_prefetch_reset'
drivers/mtd/nand/raw/omap2.c:946: warning: Function parameter or member 'chip' not described in 'omap_enable_hwecc'
drivers/mtd/nand/raw/omap2.c:946: warning: Excess function parameter 'mtd' description in 'omap_enable_hwecc'
drivers/mtd/nand/raw/omap2.c:1017: warning: Function parameter or member 'chip' not described in 'omap_dev_ready'
drivers/mtd/nand/raw/omap2.c:1017: warning: Excess function parameter 'mtd' description in 'omap_dev_ready'
drivers/mtd/nand/raw/omap2.c:1036: warning: Function parameter or member 'chip' not described in 'omap_enable_hwecc_bch'
drivers/mtd/nand/raw/omap2.c:1036: warning: Excess function parameter 'mtd' description in 'omap_enable_hwecc_bch'
drivers/mtd/nand/raw/omap2.c:1142: warning: Function parameter or member 'ecc_calc' not described in '_omap_calculate_ecc_bch'
drivers/mtd/nand/raw/omap2.c:1142: warning: Excess function parameter 'ecc_code' description in '_omap_calculate_ecc_bch'
drivers/mtd/nand/raw/omap2.c:1270: warning: Function parameter or member 'ecc_calc' not described in 'omap_calculate_ecc_bch_sw'
drivers/mtd/nand/raw/omap2.c:1270: warning: Excess function parameter 'ecc_code' description in 'omap_calculate_ecc_bch_sw'
drivers/mtd/nand/raw/omap2.c:1284: warning: Function parameter or member 'ecc_calc' not described in 'omap_calculate_ecc_bch_multi'
drivers/mtd/nand/raw/omap2.c:1284: warning: Excess function parameter 'ecc_code' description in 'omap_calculate_ecc_bch_multi'
drivers/mtd/nand/raw/omap2.c:1681: warning: Function parameter or member 'info' not described in 'is_elm_present'
drivers/mtd/nand/raw/omap2.c:1681: warning: Function parameter or member 'elm_node' not described in 'is_elm_present'
drivers/mtd/nand/raw/omap2.c:1681: warning: Excess function parameter 'omap_nand_info' description in 'is_elm_present'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Jian Zhang <jzhang@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-20-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_steps' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_step_size' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:102: warning: Function parameter or member 'ecc_syndrome_size' not described in 'elm_config'
drivers/mtd/nand/raw/omap_elm.c:440: warning: Function parameter or member 'info' not described in 'elm_context_save'
drivers/mtd/nand/raw/omap_elm.c:488: warning: Function parameter or member 'info' not described in 'elm_context_restore'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-19-lee.jones@linaro.org
Correct 'controller' typo while we're at it.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/s3c2410.c:172: warning: Function parameter or member 'controller' not described in 's3c2410_nand_info'
drivers/mtd/nand/raw/s3c2410.c:172: warning: Function parameter or member 'freq_transition' not described in 's3c2410_nand_info'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Ben Dooks <ben@simtec.co.uk>
Cc: linux-mtd@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-18-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/cafe_nand.c:372: warning: Function parameter or member 'page' not described in 'cafe_nand_read_page'
drivers/mtd/nand/raw/cafe_nand.c:372: warning: Excess function parameter 'mtd' description in 'cafe_nand_read_page'
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-17-lee.jones@linaro.org
'dummy' is never checked (as per the nomenclature) and the use of
'emtpymatch' is currently #if 0'ed out. We could also #if 0 the
declaration, but #ifery is pretty ugly, so I like to keep it to a
minimum.
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/diskonchip.c: In function ‘DoC_Delay’:
drivers/mtd/nand/raw/diskonchip.c:219:16: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
drivers/mtd/nand/raw/diskonchip.c: In function ‘doc200x_calculate_ecc’:
drivers/mtd/nand/raw/diskonchip.c:706:6: warning: variable ‘emptymatch’ set but not used [-Wunused-but-set-variable]
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Dan Brown <dan_brown@ieee.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-16-lee.jones@linaro.org
Fixes the following W=1 kernel build warning(s):
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'host' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'addr' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'buf' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'len' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1854: warning: Function parameter or member 'cmd' not described in 'brcmnand_edu_trans'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'host' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'addr' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'buf' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'len' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'dma_cmd' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'begin' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'end' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1951: warning: Function parameter or member 'next_desc' not described in 'brcmnand_fill_dma_desc'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'host' not described in 'brcmnand_dma_run'
drivers/mtd/nand/raw/brcmnand/brcmnand.c:1977: warning: Function parameter or member 'desc' not described in 'brcmnand_dma_run'
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: linux-mtd@lists.infradead.org
Cc: bcm-kernel-feedback-list@broadcom.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201109182206.3037326-14-lee.jones@linaro.org
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-20-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-18-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-17-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-16-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-15-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-14-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-13-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-12-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-10-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-8-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-7-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-5-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip().
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-4-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip(), a NAND controller
hook.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-3-miquel.raynal@bootlin.com
The probe function is only supposed to initialize the controller
hardware but not the ECC engine. Indeed, we don't know anything about
the NAND chip(s) at this stage. Let's move the logic initializing the
ECC engine, even pretty simple, to the ->attach_chip() hook which gets
called during nand_scan() routine, after the NAND chip discovery. As
the previously mentioned logic is supposed to parse the DT for us, it
is likely that the chip->ecc.* entries be overwritten. So let's avoid
this by moving these lines to ->attach_chip(), a NAND controller
hook.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/linux-mtd/20201113123424.32233-2-miquel.raynal@bootlin.com
Since commit d7157ff49a ("mtd: rawnand: Use the ECC framework user
input parsing bits"), ECC are broken in FMC2 driver in case of
nand-ecc-step-size and nand-ecc-strength are not set in the device tree.
To avoid this issue, the default settings are now set in
stm32_fmc2_nfc_attach_chip function.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/1604064819-26861-1-git-send-email-christophe.kerello@st.com
No ECC initialization should happen during the host controller probe.
In fact, we need the probe function to call nand_scan() in order to:
- identify the device, its capabilities and constraints (nand_scan_ident())
- configure the ECC engine accordingly (->attach_chip())
- scan its content and prepare the core (nand_scan_tail())
Moving these lines to fsl_ifc_attach_chip() fixes a regression caused by
a previous commit supposed to clarify these steps.
Based on a fix done for the mxc_nand driver by Miquel Raynal.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Han Xu <xhnjupt@gmail.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Han Xu <xhnjupt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201016132626.30112-1-festevam@gmail.com
No ECC initialization should happen during the host controller probe.
In fact, we need the probe function to call nand_scan() in order to:
- identify the device, its capabilities and constraints (nand_scan_ident())
- configure the ECC engine accordingly (->attach_chip())
- scan its content and prepare the core (nand_scan_tail())
Moving these lines to mxcnd_attach_chip() fixes a regression caused by
a previous commit supposed to clarify these steps.
When moving the ECC initialization from probe() to attach(), get rid
of the pdata usage to determine the engine type and let the core decide
instead.
Tested on a imx27-pdk board.
Fixes: d7157ff49a ("mtd: rawnand: Use the ECC framework user input parsing bits")
Reported-by: Fabio Estevam <festevam@gmail.com>
Co-developed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20201016213613.1450-1-festevam@gmail.com
There is an error message within devm_ioremap_resource already, so
remove the dev_err call to avoid a redundant error message.
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200921013805.1724606-1-liushixin2@huawei.com
Commit 7c2f66a960 ("mtd: rawnand: ams-delta: Add module device
tables") introduced an OF module device table but wrapped a reference
to it with of_match_ptr() which resolves to NULL in non-OF configs.
That resulted in a clang compiler warning on unused variable in non-OF
builds. Fix it.
drivers/mtd/nand/raw/ams-delta.c:373:34: warning: unused variable 'gpio_nand_of_id_table' [-Wunused-const-variable]
static const struct of_device_id gpio_nand_of_id_table[] = {
^
1 warning generated.
Fixes: 7c2f66a960 ("mtd: rawnand: ams-delta: Add module device tables")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200919080403.17520-1-jmkrzyszt@gmail.com
The error code received from nand_set_ecc_soft_ops() was overwritten,
drop this redundant assignment and use the error code received from
the callee.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200917075213.532161-4-tudor.ambarus@microchip.com
There were too many levels of indentation and the code was
hard to read. Introduce a new function, similar to
nand_set_ecc_soft_ops().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200917075213.532161-3-tudor.ambarus@microchip.com
In atmel_nand_pmecc_read_pg(), nand_read_data_op() is called twice
without the return values being checked for errors. Add these checks.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200914214245.14626-1-alex.dewar90@gmail.com
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-6-krzk@kernel.org
Fix kerneldoc comments and add missing documentation for members to fix
W=1 compile warnings like:
drivers/mtd/nand/raw/marvell_nand.c:251: warning:
cannot understand function prototype: 'struct marvell_hw_ecc_layout '
drivers/mtd/nand/raw/marvell_nand.c:342: warning:
Function parameter or member 'layout' not described in 'marvell_nand_chip'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-5-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-4-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-3-krzk@kernel.org
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200901142535.12819-2-krzk@kernel.org
vf610_nfc_probe() does not invoke clk_disable_unprepare() on one error
handling path. The patch fixes that.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 6f0ce4dfc5 ("mtd: rawnand: vf610: Avoid a potential NULL pointer dereference")
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200806072634.23528-1-novikov@ispras.ru
The sparse tool complains as follows:
drivers/mtd/nand/raw/pasemi_nand.c:71:5: warning:
symbol 'pasemi_device_ready' was not declared. Should it be static?
This function is not used outside of pasemi_nand.c, so this commit
marks it static.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200721151657.41027-1-weiyongjun1@huawei.com
Now that exec_op() is implemented, we can get rid of all the legacy
hooks.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200720131356.1579073-7-tudor.ambarus@microchip.com
