Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov2685 driver by attempting to parse them from firmware.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
If the sensor doens't power up correctly, for example due to incorrect
devicetree description, the power up i2c writes will fail.
Add an error print for this situation.
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx296 driver uses the subdev active state, there's no need to
implement the .get_fmt() operation manually. Use the
v4l2_subdev_get_fmt() helper instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5670 driver tries to get a reference to the xvclk provider by using
the common cock framework and deflects to parsing the "clock-frequency"
property in case the clock provider is not specified in the firmware
interface, detected by checking if ov5670->xvclk == PTR_ERR(-ENOENT).
However, as reported by the Smatch static checker, if CONFIG_HAVE_CLK is
not enabled, devm_clk_get() returns 0 which when passed to PTR_ERR()
means success causing the driver to fail without propagating any error
code up.
Explicitly handle the case where ov5670->xvclk it set to NULL, forcing
the code to parse the "clock-frequency" property in case CONFIG_HAVE_CLK
is not enabled, as suggested by Dan Carpenter.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently the driver always configures the sensor for dual-lane MIPI
output, but it also supports single-lane output. Add support for that by
checking the data-lanes fwnode property how many lanes are used and
configure the necessary registers based on that.
To achieve this we move setting register 0x3018 out of the general reg
sequence so we set it to the correct value. The pixel_rate value also
needs to be adjusted.
[Sakari Ailus: Use div_s64 to divide a 64-bit number]
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace the unusual const char *err_msg usage with dev_err_probe which
also handles -EPROBE_DEFER better by not printing the message to kmsg.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Both sensors are quite similar. Their specs only differ regarding LVDS
and parallel output but are identical regarding MIPI-CSI-2 interface.
But they use a different init setting of hard-coded values, taken from
the datasheet.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
imx290_start_streaming logs what failed, but not the error
code from that function. Add it into the log message.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports H & V flips, so add the relevant hooks for
V4L2_CID_HFLIP and V4L2_CID_VFLIP to configure them.
Note that the Bayer order is maintained as the readout area
shifts by 1 pixel in the appropriate direction (note the
comment about the top margin being 8 pixels whilst the bottom
margin is 9). The V4L2_SEL_TGT_CROP region is therefore
adjusted appropriately.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor supports either a 37.125 or 74.25MHz external, but
the driver only supported 37.125MHz.
Add the relevant register configuration for either clock
frequency option.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
IMX290_CTRL_07 was written from both imx290_global_init_settings
and imx290_1080p_settings and imx290_720p_settings.
Remove it from imx290_global_init_settings as the setting varies
based on the mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The default VMAX for 60fps in 720p mode is 750 according to the
datasheet, however the driver always left it at 1125 thereby stopping
60fps being achieved.
Make VMAX (and therefore V4L2_CID_VBLANK) mode dependent so that 720p60
can be achieved.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_VBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
V4L2_CID_VBLANK also sets the limits for the exposure control,
therefore exposure ranges have to be updated when vblank changes
(either via s_ctrl, or via changing mode).
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The driver exposed V4L2_CID_HBLANK as a read only control to allow
for exposure calculations and determination of the frame rate.
Convert to a read/write control so that the frame rate can be
controlled.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" added support for the increased link frequencies
on 2 data lanes, but didn't update the CSI timing registers in
accordance with the datasheet.
Use the specified settings.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Commit "97589ad61c73 media: i2c: imx290: Add support for 2 data lanes"
added support for running in two lane mode (instead of 4), but
without changing the link frequency that resulted in a max of 30fps.
Commit "98e0500eadb7 media: i2c: imx290: Add configurable link frequency
and pixel rate" then doubled the link frequency when in 2 lane mode,
but didn't undo the correction for running at only 30fps, just extending
horizontal blanking instead.
Remove the 30fps limit on 2 lane by correcting the register config
in accordance with the datasheet for 60fps operation over 2 lanes.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The datasheet lists the link frequency changes between
1080p and 720p modes. This is correct that the link frequency
changes as measured on an oscilloscope.
Link frequency is not necessarily the same as pixel rate.
The datasheet gives standard configurations for 1080p and 720p
modes at a number of frame rates.
Looking at the 1080p mode it gives:
HMAX = 0x898 = 2200
VMAX = 0x465 = 1125
2200 * 1125 * 60fps = 148.5MPix/s
Looking at the 720p mode it gives:
HMAX = 0xce4 = 3300
VMAX = 0x2ee = 750
3300 * 750 * 60fps = 148.5Mpix/s
This driver currently scales the pixel rate proportionally to the
link frequency, however the above shows that this is not the
correct thing to do, and currently all frame rate and exposure
calculations give incorrect results.
Correctly report the pixel rate as being 148.5MPix/s under any
mode.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Any V4L2 subdevice that implements controls and declares
V4L2_SUBDEV_FL_HAS_DEVNODE should also declare V4L2_SUBDEV_FL_HAS_EVENTS
and implement subscribe_event and unsubscribe_event hooks.
This driver didn't and would therefore fail v4l2-compliance
testing.
Add the relevant hooks.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The colorspace fields were left untouched in imx290_set_fmt
which lead to a v4l2-compliance failure.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX290 module is available as either mono or colour (Bayer).
Update the driver so that it can advertise the correct mono
formats instead of the colour ones.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5647_read() functions calls i2c_master_send() and
i2c_master_read() in sequence. However this leaves space for other
clients to contend the bus and insert an unrelated transaction in between
the two calls.
Replace the two calls with a single i2c_transfer() one, that locks the
bus in between the transactions.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Tommaso Merciai <tomm.merciai@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
No need to call fwnode_property_read_u32(dev_fwnode()), when
we have already existing helper. So use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since we have a proper endianness converters for LE 24-bit data use them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
tx_from_ep's for loop uses '5' as bound, while in fact it refers to the
number of polarities. Replace it by VGXY61_NB_POLARITIES for
factorization.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In case of error 'update_hdr' now goes through 'power_off' instead of
returning, effectively shutting down the sensor.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Previously the device detection was performed after patching.
Move it right after the reset to make sure we have the correct sensor
before trying to patch it.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
At this stage the default mode is unknown.
This is done correctly by vgxy61_fill_framefmt right after.
Signed-off-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The runtime suspend/resume functions are only referenced from the
dev_pm_ops, but they use the old SET_RUNTIME_PM_OPS() helper
that requires a __maybe_unused annotation to avoid a warning:
drivers/media/i2c/imx290.c:1082:12: error: unused function 'imx290_runtime_resume' [-Werror,-Wunused-function]
static int imx290_runtime_resume(struct device *dev)
^
drivers/media/i2c/imx290.c:1090:12: error: unused function 'imx290_runtime_suspend' [-Werror,-Wunused-function]
static int imx290_runtime_suspend(struct device *dev)
^
Convert this to the new RUNTIME_PM_OPS() helper that so this
is not required. To improve this further, also use the pm_ptr()
helper that lets the dev_pm_ops get dropped entirely when
CONFIG_PM is disabled.
A related mistake happened in the of_match_ptr() macro here, which
like SET_RUNTIME_PM_OPS() requires the match table to be marked
as __maybe_unused, though I could not reproduce building this without
CONFIG_OF. Remove the of_match_ptr() here as there is no point in
dropping the match table in configurations without CONFIG_OF.
Fixes: 02852c01f6 ("media: i2c: imx290: Initialize runtime PM before subdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102838.16448-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102705.16092-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the media bus is unsupported, then return -EINVAL. Instead it
returned 'ret' which happened to be 0.
This fixes a smatch warning:
ov7670.c:1843 ov7670_parse_dt() warn: missing error code? 'ret'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 01b8444828 ("media: v4l2: i2c: ov7670: Implement OF mbus configuration")
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since 'ret' is known to be 0, just return '0'. This fixes a smatch warning:
s5c73m3-core.c:439 __s5c73m3_s_stream() warn: missing error code? 'ret'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are no existing users of s5c73m3_platform_data in the tree, and
new users should either be using device tree, ACPI, or static device
properties, so let's remove it from the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add driver for the Sony IMX415 CMOS image sensor.
Signed-off-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Co-developed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5670 driver registers three controls as read-only:
- V4L2_CID_PIXEL_RATE
- V4L2_CID_LINK_FREQ
- V4L2_CID_HBLANK
The driver updates the range of HBLANK with __v4l2_ctrl_modify_range()
and updates the values of PIXEL_RATE and LINK_FREQ with an
explicit call to __v4l2_ctrl_s_ctrl() in ov5670_set_pad_format() time.
This causes the .set_ctrl handler to be called on these controls
causing a non-fatal warning to be emitted:
ov5670_set_ctrl Unhandled id:0x9e0902, val:0x824
This is currently only critical for HBLANK, as LINK_FREQ and PIXEL_RATE
currently only support a single value, and the v4l2-ctrl framework skips
calling .set_ctrl() if the current control value is not changed.
Expand the ov5670_set_ctrl() callback to handle the above controls
to remove the above warning and defend against future expansions
of the supported pixel rates and link frequencies.
Also be stricter and return an error value if a control is actually not
handled.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for the .get_selection() pad operation to the ov5670 sensor
driver.
Report the native sensor size (pixel array), the crop bounds (readable
pixel array area) and the current and default analog crop rectangles.
Currently all driver's modes use an analog crop rectangle of size
[12, 4, 2600, 1952]. Instead of hardcoding the value in the operation
implementation, ad an .analog_crop field to the sensor's modes
definitions, to make sure that if any mode gets added, its crop
rectangle will be defined as well.
While at it re-sort the modes' field definition order to match the
declaration order and initialize the crop rectangle in init_cfg().
[Sakari Ailus: Fix a typo on comments (03800 -> 0x3800)]
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the .init_cfg() pad operation and initialize the default
format with the default full resolution mode 2592x1944.
With .init_cfg() pad operation implemented the deprecated .open()
internal operation can now be dropped.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the runtime resume and suspend routines and install them as
runtime_pm handlers.
While at it rework the probe() sequence in order to enable runtime_pm
before registering the async subdevice.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV5670 has a powerdown and reset pin, named respectively "PWDN" and
"XSHUTDOWN".
Optionally probe the gpios connected to the pins during the driver probe
routine.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV5670 has three power supplies (AVDD, DOVDD and DVDD).
Probe them in the driver to prepare controlling with runtime_pm
operations.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for probing the main system clock using the common clock
framework and its OF bindings.
Maintain ACPI compatibility by falling back to parse 'clock-frequency'.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5670 driver currently only supports probing using ACPI matching.
Add support for OF and add a missing header inclusion.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor has 2592*1944 active pixels, surrounded by 16 active dummy
pixels and there are an additional 24 black rows "at the bottom".
[2624]
+-----+------------------+-----+
| | 16 dummy | |
+-----+------------------+-----+
| | | |
| | [2592] | |
| | | |
|16 | valid | 16 |[2000]
|dummy| |dummy|
| | [1944]| |
| | | |
+-----+------------------+-----+
| | 16 dummy | |
+-----+------------------+-----+
| | 24 black lines | |
+-----+------------------+-----+
The top-left coordinate is gotten from the registers specified in the
modes which are identical for both currently supported modes.
There are currently two modes supported by this driver: 2592*1944 and
1296*972. The second mode is obtained thanks to subsampling while
keeping the same field of view (FoV). No cropping involved, hence the
harcoded values.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Until now, this driver only supported ACPI. This adds support for
Device Tree too while enabling clock and regulators in runtime PM.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2x2 binning works fine for RAW10 capture, but for RAW8 1232p mode it
leads to corrupted frames [1][2].
Using the special 2x2 analog binning mode fixes the issue, but causes
artefacts for RAW10 1232p capture. So here we choose the binning mode
depending upon the frame format selected.
As both binning modes work fine for 480p RAW8 and RAW10 capture, it can
share the same code path as 1232p for selecting binning mode.
[1] https://forums.raspberrypi.com/viewtopic.php?t=332103
[2] https://github.com/raspberrypi/libcamera-apps/issues/281
Fixes: 22da1d56e9 ("media: i2c: imx219: Add support for RAW8 bit bayer format")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX296LLR is a monochrome 1.60MP CMOS sensor from Sony. The driver
supports cropping and binning (but not both at the same time due to
hardware limitations) and exposure, gain, vertical blanking and test
pattern controls.
Preliminary support is also included for the color IMX296LQR sensor.
[Sakari Ailus: Make driver's remove function return void]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Gain control is badly documented in publicly available (including
leaked) documentation.
There is an AGC pre-gain in register 0x3a13, expressed as a 6-bit value
(plus an enable bit in bit 6). The driver hardcodes it to 0x43, which
one application note states is equal to x1.047. The documentation also
states that 0x40 is equel to x1.000. The pre-gain thus seems to be
expressed as in 1/64 increments, and thus ranges from x1.00 to x1.984.
What the pre-gain does is however unspecified.
There is then an AGC gain limit, in registers 0x3a18 and 0x3a19,
expressed as a 10-bit "real gain format" value. One application note
sets it to 0x00f8 and states it is equal to x15.5, so it appears to be
expressed in 1/16 increments, up to x63.9375.
The manual gain is stored in registers 0x350a and 0x350b, also as a
10-bit "real gain format" value. It is documented in the application
note as a Q6.4 values, up to x63.9375.
One version of the datasheet indicates that the sensor supports a
digital gain:
The OV5640 supports 1/2/4 digital gain. Normally, the gain is
controlled automatically by the automatic gain control (AGC) block.
It isn't clear how that would be controlled manually.
There appears to be no indication regarding whether the gain controlled
through registers 0x350a and 0x350b is an analogue gain only or also
includes digital gain. The words "real gain" don't necessarily mean
"combined analogue and digital gains". Some OmniVision sensors (such as
the OV8858) are documented as supoprting different formats for the gain
values, selectable through a register bit, and they are called "real
gain format" and "sensor gain format". For that sensor, we have (one of)
the gain registers documented as
0x3503[2]=0, gain[7:0] is real gain format, where low 4 bits are
fraction bits, for example, 0x10 is 1x gain, 0x28 is 2.5x gain
If 0x3503[2]=1, gain[7:0] is sensor gain format, gain[7:4] is coarse
gain, 00000: 1x, 00001: 2x, 00011: 4x, 00111: 8x, gain[7] is 1,
gain[3:0] is fine gain. For example, 0x10 is 1x gain, 0x30 is 2x gain,
0x70 is 4x gain
(The second part of the text makes little sense)
"Real gain" may thus refer to the combination of the coarse and fine
analogue gains as a single value.
The OV5640 0x350a and 0x350b registers thus appear to control analogue
gain. The driver incorrectly uses V4L2_CID_GAIN as V4L2 has a specific
control for analogue gain, V4L2_CID_ANALOGUE_GAIN. Use it.
If registers 0x350a and 0x350b are later found to control digital gain
as well, the driver could then restrict the range of the analogue gain
control value to lower than x64 and add a separate digital gain control.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make the driver get needed regulators on probe and enable/disable
them on runtime PM callbacks.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is not need anyway as the i2c_client is stored in v4l2_subdev.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some module manufacturers [1][2] don't expose the RESETB and PWDN pins
of the sensor directly through the 15-pin FFC connector. Instead wiring
~PWDN gpio to the sensor pins with appropriate delays.
In such cases, reset_gpio will not be available to the driver, but it
will still be toggled when the sensor is powered on, and thus we should
still honor the wait time of >= 5ms + 1ms + 20ms (see figure 2-3 in [3])
before attempting any i/o operations over SCCB.
Also, rename the function to ov5640_powerup_sequence to better match the
datasheet (section 2.7).
[1] https://digilent.com/reference/_media/reference/add-ons/pcam-5c/pcam_5c_sch.pdf
[2] https://www.alinx.com/public/upload/file/AN5641_User_Manual.pdf
[3] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the register-based reset out of the init_setting[] and into the
powerup_sequence function. The sensor is power cycled and reset using
the gpio pins so the soft reset is not always necessary.
This also ensures that soft reset honors the timing sequence
from the datasheet [1].
[1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonaboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is no point to specify asm-generic for the unaligned.h.
Drop the 'generic' suffix and move the inclusion to be after
the non-media linux/* ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Otherwise autosuspend delay doesn't work and power is cut off
immediately as device is freed.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a driver for OmniVision OV8858 image sensor.
The driver currently supports operations with 2 and 4 data lanes, in
full resolution and half-binned resolution modes.
The driver has been upported from the PinephonePro BSP available at
https://gitlab.com/pine64-org/linux.git
at commit 8c4a90c12dc2 ("media: i2c: ov8858: Use default subdev
name").
Signed-off-by: Nicholas Roth <nicholas@rothemail.net>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Check the error status returned by imx290_set_data_lanes() in its
caller and propagate it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no need to check for an incorrect number of data lanes in
imx290_set_data_lanes() as the value is validated at probe() time. Drop
the check.
The PHY_LANE_NUM and CSI_LANE_MODE registers are programmed with a value
equal to the number of lanes minus one. Compute it instead of handling
it in the switch/case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no need to configure the data lanes in the runtime PM resume
handler. Do so in imx290_start_streaming() instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initializing the subdev before runtime PM means that no subdev
initialization can interact with the runtime PM framework. This can be
problematic when modifying controls, as the .s_ctrl() handler commonly
calls pm_runtime_get_if_in_use(). These code paths are not trivial,
making the driver fragile and possibly causing subtle bugs.
To make the subdev initialization more robust, initialize runtime PM
first.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use runtime PM autosuspend to avoid powering off the sensor during fast
stop-reconfigure-restart cycles. This also fixes runtime PM handling in
the probe function that didn't suspend the device, effectively leaving
it resumed forever.
While at it, improve documentation of power management in probe() and
remove().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx290_pixfmt structure contains information about formats,
currently limited to the bpp value. Extend it with the register settings
for each format, and rename it to imx290_format_info to make its purpose
clearer. Add a function named imx290_format_info() to look up format
info for a media bus code, and use it through the code. This allows
dropping the imx290 bpp field as the value is now looked up dynamically.
The error handling in imx290_setup_format() can also be dropped, as the
format is guaranteed by imx290_set_fmt() to be valid.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the V4L2 subdev active state API to store the active format. This
simplifies the driver not only by dropping the imx290 current_format
field, but it also allows dropping the imx290 lock, replaced with the
state lock.
The lock check in imx290_ctrl_update() can be dropped as
imx290_set_fmt() can't be called anywmore with which set to ACTIVE
before controls are initialized.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the external clock initialization code from probe() to a separate
function to improve readability. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Improve error handling in the probe() function with dev_err_probe().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make the probe() function more readable by factoring out the DT parsing
code to a separate function. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The black level programmed in the BLKLEVEL register depends on the
output format. The black level value computation is currently performed
in imx290_set_ctrl(), in addition to having different black level values
in the output-specific register value tables. Move it to a separate
function to simplify the imx290_set_ctrl() code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The hblank, vblank, pixel rate and link frequency values and limits are
currently computed when creating controls, in imx290_ctrl_init(), and
updated in imx290_ctrl_update(). This duplicates the logic in different
places. Simplify the code by setting the control values and limits to
hardcoded values when creating the controls, and call
imx290_ctrl_update() to then update them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Avoid accessing the imx290 current_format and current_mode fields in
imx290_calc_pixel_rate() to prepare for the removal of those fields.
Among the two callers of the function, imx290_ctrl_update() has an
explicit mode pointer already, and we can also give it a format pointer.
Use those explicitly.
While at it, inline the imx290_get_link_freq() function in
imx290_calc_pixel_rate() as it is only called there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx290_get_link_freq_index() function hides the fact that it relies
on the imx290 current_mode field, which obfuscates the code instead of
making it more readable. Inline it in the callers, and use the mode
pointer we already have in imx290_ctrl_update() instead of using the
current_mode field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the control update code to a separate function to group it with all
the control-related code and make imx290_set_fmt() more readable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The probe() function is large. Make it more readable by factoring the
subdev initialization code out. While at it, rename the error labels as
the "free_" prefix isn't accurate.
No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move functions around to group them in logical sections, in order to
improve readability. As a result, the IMX290_NUM_SUPPLIES macro has to
be changed. No other code change is included, only moves.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In commit a89f14bbcf ("media: ov5640: Split DVP and CSI-2 formats"),
it splits format list for DVP and CSI-2 mode, but the default format
defined in commit 90b0f355c5 ("media: ov5640: Implement init_cfg")
is only supported by DVP mode, so define a new default format for
CSI-2 mode.
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx219 camera is capable of either two-lane or four-lane
operation. When operating in four-lane, both the pixel rate and
link frequency change. Regardless of the mode, however, both
frequencies remain fixed.
Helper functions are needed to read and set pixel and link frequencies
which also reduces the number of fixed registers in the table of modes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are four modes, and each mode has a table of registers.
Some of the registers are common to all modes, so create new
tables for these common registers to reduce duplicate code.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Using the u64 v4l2_dbg_register.val directly can lead to unexpected
results depending on machine endianness. Fix this by using a local
variable which is assigned afterwards. Since tc358746_read() will init
the val variable to 0 we can assing it without checking the return value
first.
Addresses-Coverity-ID: 1527256 ("Integer handling issues")
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Fixes: 80a21da360 ("media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Currently we ignore the return value of tc358746_read() and return
alawys return 0 which is wrong. Fix this by returning the actual return
value of the read operation which is either 0 on success or an error
value.
Addresses-Coverity-ID: 1527254 ("Error handling issues")
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Fixes: 80a21da360 ("media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
It was intended to return an error if tc358746_update_bits() call fail.
Fix this by storing the return code.
Addresses-Coverity-ID: 1527252 ("Control flow issues")
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Fixes: 80a21da360 ("media: tc358746: add Toshiba TC358746 Parallel to CSI-2 bridge driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The power-up GMSL link configuration is controlled by the HIM and BWS
pins, whose state is reflected in register 0x1c. Print the detected
power-up config in a debug message to help debugging.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
GMSL can transport three synchronization signals: VSync, HSync and Data
Enable. The MAX9286 can select either HS or DE as a line valid signal.
Not all serializers (and transmission formats) support the DE signal.
The MAX9271, used by the RDACM20 and RDACM21 cameras, doesn't document
DE support. Nonetheless, the max9286 driver selects the DE signal as
line valid in register 0x0c (by not setting the DESEL bit). It's not
clear why this works. As HS is a more common line valid qualifier, set
the DESEL bit by default. This is needed to support the onsemi MARS
cameras.
If a camera requires usage of the DE signal in the future, this will
need to be made configurable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo@jmondi.org> # On Eagle V3M with RDACM20
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The GMSL serial data bus width is normally selected through the BWS pin.
On some systems, the pin may not be wired to the correct value. Support
overriding the bus width by software, using the value specified in the
device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Read the maxim,i2c-clock-frequency DT property that specifies the speed
of the remote I2C bus, and configure the MAX9286 accordingly. The remote
serializers must all have a matching configuration.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for 12-bit raw bayer formats to the driver, configuring the
GMSL format accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The MAX9286_DATATYPE_RAW11 value is used to configure the MAX9286 for
11-bit or 12-bit input data. While 11-bit data is supported on the GMSL
side, CSI-2 doesn't have a RAW11 format. 11-bit data is transferred over
CSI-2 as RAW12. Rename the macro accordingly to avoid confusion.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The MAX9286 can generate a framesync signal to synchronize the cameras,
using an internal timer. Support this mode of operation and configure it
through the .s_frameinterval() operation. If the frame interval is not
0, framesync is switched to manual mode with the specified interval,
otherwise automatic mode is used.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Allow users to use one PoC regulator per port, instead of a global
regulator.
The properties '^port[0-3]-poc-supply$' in the DT node are used to
indicate the regulators for individual ports.
Signed-off-by: Thomas Nizan <tnizan@witekio.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
[hverkuil: remove obsolete kerneldoc 'id' documentation]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
