Unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workarounds that currently use EFX_WORKAROUND_ALWAYS are in
Falcon-specific or Falcon-arch-specific code, so get rid of the
conditions altogether. Add/move comments as appropriate.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
EF10 functions don't have a fixed BAR size, and the minimum is not
large enough for all the queues we might want to allocate. We have to
find out the BAR size at run-time, and therefore phys_addr_channels
and mem_map_size cannot be defined per-NIC-type.
Change efx_nic_type::mem_map_size to a function pointer which is
called to find the wanted memory map size (before probe).
Replace efx_nic_type::phys_addr_channels with efx_nic::max_channels,
to be initialised by the probe function.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
When we poll for MCDI request completion, we don't hold the interface
lock while setting the response fields in struct efx_mcdi_iface.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI v2 adds a second header dword with wider command and length
fields. It also defines extra error codes.
Change the fallback error number for unknown MCDI error codes from EIO
to EPROTO. EIO is treated as indicating the MCDI transport has failed
and we need to reset the function, which is rather drastic.
v2 error codes and lengths don't fit into completion events, so for a
v2-capable transport, always read the response header rather then
using the event fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
EF10 controllers do not have shared memory for communication with the
MC; instead it reads requests and writes responses in host memory,
which allows for longer messages. It is also responsible for all
datapath control operations and hardware resource allocation, which
requires a large number of new commands and adds more possible error
cases. MCDI v2 extends the message header to support this.
Update the MCDI protocol definition header to include v2 lengths,
errors and messages, and a few definitions specific to the
SFC9100 family (codenames Farmingdale and Huntington) which is
the first generation of EF10.
Some messages have been extended, so adjust the code accordingly:
- The request for MC_CMD_DRV_ATTACH now includes a datapath firmware
ID. This is ignored by Siena but we should fill it in anyway,
initially always specifying low-latency datapath.
- The response for MC_CMD_GET_LOOPBACK_MODES now includes a 40G
field. Accept shorter responses that don't include it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Currently we only translate error codes in efx_mcdi_poll(), but we
also need to do so in efx_mcdi_ev_cpl().
The reason we didn't notice before is that the MC firmware error codes
are mostly taken from Unix/Linux and no translation is necessary on
most architectures. Make sure we notice any future failure by
changing the sign of resprc (matching the kernel convention) and BUG
if it's ever positive at command completion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Result of skb_frag_dma_map() and dma_map_single() wasn't checked.
Added a check and proper handling in case of failure.
Moved the mapping to the beginning of mlx4_en_xmit(), before updating
the ring data structure to make error handling easier.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware gets into error state, must notify user about it.
When QP in error state no traffic will be tx'ed from the attached
tx_ring.
Driver should know how to recover from this unexpected state. I will send later
on the recovery flow, but having the print shouldn't be delayed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug when FC and PFC are enabled/disabled at the same time.
According to ConnectX-3 Programmer Manual these two features are mutial
exclusive. So make sure when enabling PFC to turn off global FC and
vise versa. Otherwise it hurts the performance.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add efx_nic_type operations for the many efx_nic functions that need
to be implemented different on EF10. For now, change most of the
existing efx_nic_*() functions into inline wrappers. As a later step,
we may be able to improve branch prediction for operations used on the
fast path by copying the pointers into each queue/channel structure.
Move the Falcon/Siena implementations to new file farch.c and rename
the functions and static data to use a prefix of 'efx_farch_'.
Move efx_may_push_tx_desc() to nic.h, as the EF10 TX code will also
use it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Each function driver instance uses the MAC address of the
lowest function belonging to that physical port as a unique
port identifier. This port identifier is read and cached in
driver during probe and provided to user space through
ndo_get_phys_port_id()
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enable diagnostic test via ethtool and QConvergeConsole
application when Multiple Tx queues are enabled on 82xx
series adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o using ethtool {set|get}_channel option, user can change number
of Tx queues for 82xx Series adapter.
o updated ethtool -S <ethX> option to display stats from each Tx queue.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 82xx firmware allows support for multiple Tx queues. This
patch will enable multi Tx queue support for 82xx series
adapter. Max number of Tx queues supported will be 8.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently efx_stop_datapath() will try to flush our DMA queues (if DMA
is enabled), then finalise software and hardware state for each queue.
However, for EF10 we must ask the MC to finalise each queue, which
implicitly starts flushing it, and then wait for the flush events.
We therefore need to delegate more of this to the NIC type.
Combine all the hardware operations into a new NIC-type operation
efx_nic_type::fini_dmaq, and call this before tearing down the
software state and buffers for all the DMA queues.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_unregister_netdev() should not call efx_release_tx_buffers()
directly, as it is already done when closing the device:
efx_net_stop() -> efx_stop_all() -> efx_stop_datapath() ->
efx_fini_tx_queue() -> efx_release_tx_buffers().
(This was presumably a workaround for a race between efx_stop_all()
and the data path that has since been properly fixed.)
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
rx_queue::enabled guards refill, so rename it to reflect that. Clear
it at the start of the queue teardown process rather than waiting for
the RX queue to be flushed.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We unconditionally acknowledge legacy interrupts just before disabling
them. This workaround is needed on Falcon A1 but probably not on
later chips where the legacy interrupt mechanism is different. It was
also originally done after the IRQ handler was removed, not before.
Restore the original behaviour for Falcon A1 only by doing this
acknowledgement in the efx_nic_type::fini operation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
There are many problems with the current efx_stop_interrupts() and
efx_start_interrupts():
1. On Siena, it is unsafe to disable the master IRQ enable bit
(DRV_INT_EN_KER) while any IRQ sources are enabled.
2. On EF10 there is no master IRQ enable bit, so we cannot expect to
defer IRQs without tearing down event queues. (Though I don't think
we will need to keep any event queues around while the device is down,
as we do for VFDI on Siena.)
3. synchronize_irq() only waits for a running IRQ handler to finish,
not for any propagation through IRQ controllers. Therefore an IRQ may
still be received and handled after efx_stop_interrupts() returns.
IRQ handlers can then race with channel reallocation.
To fix this:
a. Introduce a software IRQ enable flag. So long as this is clear,
IRQ handlers will only acknowledge IRQs and not touch the channel
structures.
b. Define a new struct efx_msi_context as the context for MSIs. This
is never reallocated and is sufficient to find the software enable
flag and the channel structure. It also includes the channel/IRQ
name, which was previously separated out as it must also not be
reallocated.
c. Split efx_{start,stop}_interrupts() into
efx_{,soft_}_{enable,disable}_interrupts(). The 'soft' functions
don't touch the hardware master enable flag (if it exists) and don't
reinitialise or tear down channels with the keep_eventq flag set.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
efx_process_channel_now() is unneeded since self-tests can rely on
normal NAPI polling. Remove it and all calls to it.
efx_channel::work_pending and efx_channel_processed() are also
unneeded (the latter being the same as efx_nic_eventq_read_ack()).
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
The EF10 architecture has a very different register layout from
previous controllers, so we'll use separate files for the two sets of
register definitions. Use 'farch' as an abbreviation for
Falcon-architecture.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
On EF10, the firmware is in charge of allocating buffer table entries.
Change struct efx_special_buffer to use a struct efx_buffer member,
so that it can be used with efx_nic_{alloc,free}_buffer() in that
case.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Most call sites for efx_nic_alloc_buffer() are part of the probe or
reconfiguration paths and can allocate with GFP_KERNEL. A few others
should use GFP_NOIO (I think). Only one is in atomic context and
must use the current GFP_ATOMIC.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Move the lowest layer (transport) of the current MCDI code to
per-NIC-type operations.
Introduce a new structure and efx_nic member for MCDI-specific data.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
This should probably be done during MCDI initialisation for any NIC.
Change efx_mcdi_init() to return an error code.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Collect together MCDI port functions from mcdi.c, mcdi_mac.c,
mcdi_phy.c and siena.c. Rename the 'siena' functions accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We currently require that MCDI request and response lengths are
multiples of 4 bytes, because we will copy dwords in and out of shared
memory and we want to be sure we won't read or write out of bounds.
But all we really need to know is that there is sufficient padding for
that. Also, we should ensure that buffers are dword-aligned, as on
some architectures misaligned access will result in data corruption or
a crash.
Change the buffer type to array-of-efx_dword_t and remove the
requirement that the lengths are multiples of 4.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
A few functions are using heap buffers; change them to use stack
buffers as we really don't need to resort to the heap for a 252
byte buffer in process context.
MC_CMD_MEMCPY is quite weird in that it can use inline data placed in
the request buffer after the array of records. Thus there are two
variable-length arrays and we can't use the normal accessors for
the second. So we have to use _MCDI_PTR() in efx_sriov_memcpy().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
We need to access arrays of 16-bit words and 32-bit dwords in MCDI
buffers based on the MCDI protocol definitions.
We should also be able to read and write fields within structures,
without specifying an array index each time. So add MCDI_FIELD()
and make MCDI_ARRAY_FIELD() use it. Also add MCDI_SET_FIELD().
Split MCDI_ARRAY_PTR() into MCDI_ARRAY_STRUCT_PTR() and
_MCDI_ARRAY_PTR(), which are currently identical but will diverge in
later changes.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Add _MCDI_DWORD() which yields an lvalue for the given dword field
and change MCDI_DWORD(), MCDI_SET_DWORD() and MCDI_QWORD() to use it.
Fold the rather trivial MCDI_PTR2() into MCDI_PTR() and _MCDI_DWORD().
Remove MCDI_SET_DWORD2() and MCDI_QWORD2(). MCDI_DWORD2() should also
go, but it still has one user which we'll get rid of later.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
MCDI_DECLARE_BUF declares a variable as an MCDI buffer of the
requested length, adding any necessary padding.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
commit 385904f819 ('sfc: Don't use
efx_filter_{build,hash,increment}() for default MAC filters') used the
wrong name to find the index of default RX MAC filters at insertion/
update time. This could result in memory corruption and would in any
case silently fail to update the filter.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Some phy's can be configured to enable wake on lan (e.g. at803x or marvell 88E1318S).
There is no way how to enable wol on CPSW with such connected phys. This patch
adds this support. It is provided by calling the phy's related code.
Tested on board with at8030x connected phy. Wol interrupt line is
connected to GPIO0 on am335x.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
The relevant call to platform_get_resource was manually moved down to the
call to devm_ioremap_resource.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of_dev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &ofdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register layout is a SoC characteristic, so it's wrong that it's stored
in the otherwise board specific platform data. Add 'register_type' field to
'struct sh_eth_cpu_data', initialize it properly for each SoC, and read it
from this structure instead of the platfrom data from now on...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not clear Broadcast/Multicast/Unicast Wake Flag or LanWake in
Config5. This is necessary to preserve WOL state when the driver is
loaded. Although the r8168 vendor driver does not write Config5 (it has
been commented out), Hayes Wang from Realtek said that masking bits like
this is more sensible.
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ndo_busy_poll handler. Use skb_mark_napi_id to mark receive
packets with the napi id. For each slice, use per-slice spinlock and
state variable to ensure that only one handler processes receive
pacekts.
Locking, statistics counters, and the ndo_busy_poll handler follow
those in the ixgbe driver. So, credit goes to that driver's authors.
Signed-off-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to change e.g. the advertising mask when the link is down
ecmd->speed is -1 causing mii_ethtool_sset() to bail out.
This bug bit when connecting to a gigabit switch through a 4-pin (industrial)
cable, since link negotiation would not complete (both endpoints claimed to
be gigabit-capable, but this is not possible with only 4 pins).
Any attempt to fix this by setting autonegation to not offer 1000Mbps
failed as the setting would not be accepted while the link was still down...
Set ecmd->speed to SPEED_1000 to satisfy mii_ethtool_sset()
(the actual value of ecmd->speed doesn't matter as long as it is valid,
since a re-negotation is forced afterwards).
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function moxart_mac_start_xmit()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool core will lower the requested length to the one returned by
get_regs_len, therefore no additional check is needed in the get_regs
function.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its resources
including queue pair filters programmed by USNIC. USNIC registers for
this notification, and on receiving it, reprograms the queue pair
filters.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an interface for USNIC to proxy firmware commands
through ENIC.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch,
- Adds new firmware commands for the new Cisco Low Latency NIC
(aka. USNIC).
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't emit OOM warnings when k.alloc calls fail when
there there is a v.alloc immediately afterwards.
Converted a kmalloc/vmalloc with memset to kzalloc/vzalloc.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
o Use appropriate firmware image file name based on device IDs.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loopback initiator function drivers should process loopback time extend AEN.
These AENs are triggered by the loopback time extend mailbox command
issued by the target function drivers.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 84xx adapters support VLAN stripping for PVID. Packets don't have
VLAN tag inserted in case of PVID. So packet should follow non vlan path.
o Use capability bit to set PVID mode.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are possible HW configurations in which PFs will have SR-IOV capability
but will have Max VFs set to 0 - this happens when there are Multi-Function
devices where the VFs are allocated to only some of the PFs.
DMAE is configured to support VFs only if the configuring PF has supported VFs.
In case the first PF to be loaded will be one without supported VFs, it will
not configure DMAE to the VF-supporting mode. When VFs of other PFs will be
loaded later on, they will not be able to communicate with their PF.
This changes the requirement for configuring DMAE for VF-supporting mode;
If the device has SR-IOV capabilities there must be some PF that has
max supported VFs > 0, thus it will configure the DMAE for supporting VFs.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since SR-IOV can be activated dynamically and iproute2 can be called
asynchronously, the various callbacks need a robust sanity check before
attempting to access the SR-IOV database and members since there are numerous
states in which it can find the driver (e.g., PF is down, sriov was not enabled
yet, VF is down, etc.).
In many of the states the callback result will be null pointer dereference.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, VFs might erroneously try to access the shared memory (which
only PFs are capabale of accessing), causing benign attentions to appear.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When publishing information via getfeatcfg(), bnx2x driver didn't consider
remote errors (e.g., switch that doesn't support DCBX) when setting the
error flags.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After notification that DCBX configuration has ended arrived to the driver,
the driver configured the FW/HW in sleepless context.
As a result, it was possible to reach a race (mostly with CNIC registration)
in which the configuration will return a timeout, failing to set the DCBX
results correctly.
This patch moves the configuration following the DCBX end into the slowpath
RTNL task (i.e., sleepless context protected by the RTNL lock), allowing the
configuration to cope with such races.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 3deb816 "bnx2x: Add a periodic task for link PHY events"
link state changes can be detected not only via the attention flow but also
from the periodic task.
If the link state will change in such a manner (i.e., via the periodic task),
dropless flow-control will not be configured.
This patch remedies the issue, adding the missing configuration to all required
flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous QUERY_PAGES command version we used one command to get the
required amount of boot, init and post init pages. The new version uses the
op_mod field to specify whether the query is for the required amount of boot,
init or post init pages. In addition the output field size for the required
amount of pages increased from 16 to 32 bits.
In MANAGE_PAGES command the input_num_entries and output_num_entries fields
sizes changed from 16 to 32 bits and the PAS tables offset changed to 0x10.
In the pages request event the num_pages field also changed to 32 bits.
In the HCA-capabilities-layout the size and location of max_qp_mcg field has
been changed to support 24 bits.
This patch isn't compatible with firmware versions < 5; however, it turns out that the
first GA firmware we will publish will not support previous versions so this should be OK.
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Load firmware from file before setting up interrupts.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was hitting a panic at the time of adapter reset due to invalid command
access from the list which had been already freed by the queuing thread.
Flush all the pending commands from the list before proceeding with adapter reset
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o After firmware reset VFs were failing to come up because of not
reinitializing mailbox data structures. Reinitialize them so that
VFs can come up after firmware reset.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not allow interrupt test when adapter is resetting.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was misinterpreting the return status for beacon
state query leading to incorrect interpretation of beacon
state and logging an error message for successful status.
Fixed the driver to properly interpret the return status.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was issuing set driver version command through all
functions in the adapter. Fix the driver to issue set driver
version once per adapter, through function 0.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit d8af4dfd8 ("net/tg3: Fix kernel crash") introduced a possible
NULL pointer dereference in tg3 driver when !netdev || !netif_running(netdev)
condition is met and netdev is NULL. Then, the jump to the 'done' label
calls dev_close() with a netdevice that is NULL. Therefore, only call
dev_close() when we have a netdevice, but one that is not running.
[ Add the same checks in tg3_io_slot_reset() per Gavin Shan - by Nithin
Nayak Sujir ]
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Gavin Shan <shangw@linux.vnet.ibm.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers supporting NAPI should use a NAPI-specific function for receiving
packets. Hence netif_rx is changed to netif_receive_skb.
Furthermore netif_napi_del should be used in the probe and remove function
to clean up the NAPI resource information.
Thanks to Francois Romieu, David Shwatrz and Rami Rosen for their help on
this patch.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit f83331bab1.
As the tests PPC64 (powernv platform) show, IOMMU pages are leaking
when transferring big amount of small packets (<=64 bytes),
"ping -f" and waiting for 15 seconds is the simplest way to confirm the bug.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Santosh Rastapur <santosh@chelsio.com>
Cc: Jay Fenlason <fenlason@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Divy Le ray <divy@chelsio.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for some versions of firmware to advertise capabilities that driver
is not ready to handle. This may lead to controller stall. Since the driver is
interested only in subset of flags, clearing the rest.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initially I improperly set a boundary for maximum number of input
packets to process on NAPI poll ("work") so it might be more than
expected amount ("weight").
This was really harmless but seeing WARN_ON_ONCE on every device boot is
not nice. So trivial fix ("<" instead of "<=") is here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
There might be a crash as during shutdown flow CNIC might try
to access resources already freed by bnx2x.
Change bnx2x_close() into dev_close() in __bnx2x_remove (shutdown flow)
to guarantee CNIC is notified of the device's change of status.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTE write access error might occur in MF_ALLOWED mode when IOMMU
is active. The patch adds rmmod HSI indicating to MFW to stop
running queries which might trigger this failure.
Signed-off-by: Barak Witkowsky <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETS can be enabled as a result of DCB negotiation, then
fairness must be recalculated after each negotiation.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add locking to protect different statistics flows from
running simultaneously.
This in order to serialize statistics requests sent to FW,
otherwise two outstanding queries may cause FW assert.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of updates intended for 3.12. It is mostly driver
stuff, although Johannes Berg and Simon Wunderlich make a good
showing with mac80211 bits (particularly some work on 5/10 MHz
channel support).
The usual suspects are mostly represented. There are lots of updates
to iwlwifi, ath9k, ath10k, mwifiex, rt2x00, wil6210, as usual.
The bcma bus gets some love this time, as do cw1200, iwl4965, and a
few other bits here and there. I don't think there is much unusual
here, FWIW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version which is present in AM43xx SoC has a minor changes and the
offsets are same as the previous version, so adding new IP version support in
the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eTSEC has Rx and Tx flow control capabilities that may be enabled
through MACCFG1[Rx_Flow, Tx_Flow] bits. These bits must not be set
however when eTSEC is operated in Half-Duplex mode. Unfortunately,
the driver currently sets these bits unconditionally.
This patch adds the proper handling of the PAUSE frame capability
register bits by implementing the ethtool -A interface. When pause
autoneg is enabled, the controller uses the phy's capability to
negotiate PAUSE frame settings with the link partner and reconfigures
its Rx_Flow and Tx_Flow settings to match the capabilities of the
link partner. If pause autoneg is off, the PAUSE frame generation
may be forced manually (ethtool -A). Flow control is disabled by
default now.
This implementation is inspired by the tg3 driver.
Signed-off-by: Lutz Jaenicke <ljaenicke@innominate.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA sync should sync the whole receive buffer, not just
part of it. Fixes log messages dma_sync_check.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recognize XRC QPs in the SR-IOV resource tracker based on transport
type. The previous check didn't match IB_QPT_XRC_INI and caused an
invalid calculation for required mtt pages.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In stmmac_init_rx_buffers():
* add missing handling of dma_map_single() error
* remove superfluous unlikely() optimization while at it
Add stmmac_free_rx_buffers() helper and use it in dma_free_rx_skbufs().
In init_dma_desc_rings():
* add missing handling of kmalloc_array() errors
* fix handling of dma_alloc_coherent() and stmmac_init_rx_buffers() errors
* make function return an error value on error and 0 on success
In stmmac_open():
* add handling of init_dma_desc_rings() return value
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New routine has been added to avoid duplication of code to wait for
pending PCI transactions to complete. This makes use of that routine.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Acked-by: David S. Miller <davem@davemloft.net>
The Compressed LIP region is used to hold a limited number of Local
IPv6 addresses. This region is primarily used to reduce the TCAM
space consumed for an IPv6 offloaded connection. A 128-bit LIP will
be reduced to 13-bit and stored in the TCAM if there is a match
between the IPv6 tuple's LIP and the one stored in the CLIP region.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add cxgb4_create_server6 and cxgb4_remove_server routines to create
and remove listening IPv6 servers.
Return success (0) from cxgb4_create_server in case of ctrl queue
congestion since in case of congestion, passive open request gets
queued and gets processed later. If a non-zero value were returned it
would be treated as an error and the ULD would free STID, which can
result in an error in passive open reply.
Add cpl structure for active open request with IPv6 address for T5.
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The MOXA UC-711X hardware(s) has an ethernet controller that seem
to be developed internally. The IC used is "RTL8201CP".
Since there is no public documentation, this driver is mostly the
one published by MOXA that has been heavily cleaned up / ported
from linux 2.6.9.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Nithin Nayak Sujir <nsujir@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Andrew Gallatin <gallatin@myri.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: netdev@vger.kernel.org
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the condition of extend_desc for jumbo frame.
There is no check routine for extend_desc in the stmmac_jumbo_frm function.
Even though extend_desc is set if dma_tx is used instead of dma_etx.
It causes kernel panic.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in cf3c4c0306
("8139cp: Add dma_mapping_error checking")
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL and power state changes will now be done in the shutdown handler.
open/close/ethtool will no longer change the power state. NVRAM
operations can now be permitted whether the device is up or down.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Separate MAC and PHY WoL setup code into a separate function.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
by closing the device if necessary. Otherwise, since NAPI state is
already disabled, a subsequent close will hang the system.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Uninitialized value was being returned in the non-failure case.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log the event type for unknown async events
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BE2 FW GET_PHY_DETAILS cmd does not return fixed speeds supported.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SH-R and Lancer-R, use the FW supported values for Max unicast MACs,
Max VLANs and Max multicast MACs.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a chip wide value and the PFs already report it.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new speeds are supported by variants of the Skyhawk-R chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup gfar_start_xmit()'s fast path by factoring out "redundant"
FCB insertion code (repeated gfar_add_fcb() calls and related)
and by reducing the number of if() clauses (i.e. if(fcb) checks).
Improve maintainability (e.g. there's less code and easier to read)
also by introducing do_csum and do_vlan to mark the other 2 Tx TOE
functionalities, following the same model as do_tstamp.
fcb_len may also be 0 now, to mark that Tx FCB insertion conditions
(do_csum, do_vlan, do_tstamp) have not been met.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both [eTSEC76] and [eTSEC12] errata relate to Tx checksum generation
(for some MPC83xx and MCP8548 older revisions). They require the same
workaround: manual checksum computation and insertion, and disabling
the H/W Tx csum acceleration feature (per frame) through Tx FCB
(Frame Control Block) csum offload settings.
The workaround for [eTSEC76] needs to be fixed because it currently
fails to disable H/W Tx csum insertion via FCB. This patch fixes it
and provides a common workaround implementation for both Tx csum errata.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new IP version has a minor changes and the offsets are same as the
previous version, so adding new IP version support in the driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function tile_net_open()
in the error handling case.
Introduced by commit f3286a3af8.
(tile: support multiple mPIPE shims in tilegx network driver)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/mellanox/mlx4/cmd.c:803:5: warning: symbol 'MLX4_CMD_UPDATE_QP_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:812:5: warning: symbol 'MLX4_CMD_GET_OP_REQ_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:1547:5: warning: symbol 'mlx4_master_immediate_activate_vlan_qos' was not declared. Should
it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/micrel/ks8842.c:708:6: warning: symbol 'ks8842_handle_rx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:718:6: warning: symbol 'ks8842_handle_tx' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:727:6: warning: symbol 'ks8842_handle_rx_overrun' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8842.c:735:6: warning: symbol 'ks8842_tasklet' was not declared. Should it be static?
drivers/net/ethernet/micrel/ks8851_mll.c:691:6: warning: symbol 'ks_enable_qmu' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These local functions are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/emulex/benet/be_main.c:475:6: warning: symbol 'populate_erx_stats' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:1485:6: warning: symbol 'be_rx_compl_process_gro' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:2262:5: warning: symbol 'be_poll' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3223:6: warning: symbol 'flash_cookie' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_main.c:3280:27: warning: symbol 'get_fsec_info' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1013:5: warning: symbol 'be_cmd_mccq_ext_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:1071:5: warning: symbol 'be_cmd_mccq_org_create' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3166:5: warning: symbol 'be_cmd_get_profile_config_mbox' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_cmds.c:3194:5: warning: symbol 'be_cmd_get_profile_config_mccq' was not declared. Should it be
static?
drivers/net/ethernet/emulex/benet/be_roce.c:96:6: warning: symbol '_be_roce_dev_remove' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:113:6: warning: symbol '_be_roce_dev_open' was not declared. Should it be static?
drivers/net/ethernet/emulex/benet/be_roce.c:129:6: warning: symbol '_be_roce_dev_close' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bna_rx_sm_stop_wait_entry(), bna_rx_sm_rxf_stop_wait_entry(),
bna_rx_sm_started_entry(), bna_rx_sm_cleanup_wait_entry(),
and bna_rx_sm_cleanup_wait() are used only in this file.
Fix the following sparse warnings:
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1423:1: warning: symbol 'bna_rx_sm_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1476:1: warning: symbol 'bna_rx_sm_rxf_stop_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1532:1: warning: symbol 'bna_rx_sm_started_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1597:1: warning: symbol 'bna_rx_sm_cleanup_wait_entry' was not declared. Should it be
static?
drivers/net/ethernet/brocade/bna/bna_tx_rx.c:1602:1: warning: symbol 'bna_rx_sm_cleanup_wait' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove this code, per Dave Miller's request, since it is not being used
anywhere in the kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following is needed as well to fix warning/error about shifting a 32 bit
value 32 bits which occurs if building on 32 bit platform caused by conversion
to using dma_addr_t
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This old driver never checked for DMA mapping errors.
Causing splats with the new DMA mapping checks:
WARNING: at lib/dma-debug.c:937 check_unmap+0x47b/0x930()
skge 0000:01:09.0: DMA-API: device driver failed to check map
Add checks and unwind code.
Reported-by: poma <pomidorabelisima@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Don't ignore user initiated wireless regulatory settings on cards
with custom regulatory domains, from Arik Nemtsov.
2) Fix length check of bluetooth information responses, from Jaganath
Kanakkassery.
3) Fix misuse of PTR_ERR in btusb, from Adam Lee.
4) Handle rfkill properly while iwlwifi devices are offline, from
Emmanuel Grumbach.
5) Fix r815x devices DMA'ing to stack buffers, from Hayes Wang.
6) Kernel info leak in ATM packet scheduler, from Dan Carpenter.
7) 8139cp doesn't check for DMA mapping errors, from Neil Horman.
8) Fix bridge multicast code to not snoop when no querier exists,
otherwise mutlicast traffic is lost. From Linus Lüssing.
9) Avoid soft lockups in fib6_run_gc(), from Michal Kubecek.
10) Fix races in automatic address asignment on ipv6, which can result
in incorrect lifetime assignments. From Jiri Benc.
11) Cure build bustage when CONFIG_NET_LL_RX_POLL is not set and rename
it CONFIG_NET_RX_BUSY_POLL to eliminate the last reference to the
original naming of this feature. From Cong Wang.
12) Fix crash in TIPC when server socket creation fails, from Ying Xue.
13) macvlan_changelink() silently succeeds when it shouldn't, from
Michael S Tsirkin.
14) HTB packet scheduler can crash due to sign extension, fix from
Stephen Hemminger.
15) With the cable unplugged, r8169 prints out a message every 10
seconds, make it netif_dbg() instead of netif_warn(). From Peter
Wu.
16) Fix memory leak in rtm_to_ifaddr(), from Daniel Borkmann.
17) sis900 gets spurious TX queue timeouts due to mismanagement of link
carrier state, from Denis Kirjanov.
18) Validate somaxconn sysctl to make sure it fits inside of a u16.
From Roman Gushchin.
19) Fix MAC address filtering on qlcnic, from Shahed Shaikh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (68 commits)
qlcnic: Fix for flash update failure on 83xx adapter
qlcnic: Fix link speed and duplex display for 83xx adapter
qlcnic: Fix link speed display for 82xx adapter
qlcnic: Fix external loopback test.
qlcnic: Removed adapter series name from warning messages.
qlcnic: Free up memory in error path.
qlcnic: Fix ingress MAC learning
qlcnic: Fix MAC address filter issue on 82xx adapter
net: ethernet: davinci_emac: drop IRQF_DISABLED
netlabel: use domain based selectors when address based selectors are not available
net: check net.core.somaxconn sysctl values
sis900: Fix the tx queue timeout issue
net: rtm_to_ifaddr: free ifa if ifa_cacheinfo processing fails
r8169: remove "PHY reset until link up" log spam
net: ethernet: cpsw: drop IRQF_DISABLED
htb: fix sign extension bug
macvlan: handle set_promiscuity failures
macvlan: better mode validation
tipc: fix oops when creating server socket fails
net: rename CONFIG_NET_LL_RX_POLL to CONFIG_NET_RX_BUSY_POLL
...
Flash update routine was improperly checking register read API return value.
Modify register read API and perform proper error check.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set link speed and duplex to unknown when link is not up.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not obtain link speed from register when adapter
link is down.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was not handling external loopback diagnostic
test request.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Delete MAC address from the adapter's filter table
if the source MAC address of ingress packet matches.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was passing the address of a pointer instead of
the pointer itself.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQF_DISABLED is a no-op by now and should be removed.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some bnx2x devices, iSCSI is determined to be unsupported only after
firmware is downloaded. We need to check max_iscsi_conn again after
NETDEV_UP and block iSCSI init operations. Without this fix, iscsiadm
can hang as the firmware will not respond to the iSCSI init message.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fixes for the newly merged mlx5 hardware driver
- Stack info leak fixes from Dan Carpenter
- Fixes for pkey table handling with SR-IOV
- A few other small things
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ZwEX
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
- Fixes for the newly merged mlx5 hardware driver
- Stack info leak fixes from Dan Carpenter
- Fixes for pkey table handling with SR-IOV
- A few other small things
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Fix pkey change flow for virtualization environments
IPoIB: Make sure child devices use valid/proper pkeys
IB/core: Create QP1 using the pkey index which contains the default pkey
mlx5_core: Variable may be used uninitialized
mlx5_core: Implement new initialization sequence
mlx5_core: Fix use after free in mlx5_cmd_comp_handler()
IB/mlx5: Fix stack info leak in mlx5_ib_alloc_ucontext()
IB/mlx5: Fix error return code in init_one()
IB/mlx4: Use default pkey when creating tunnel QPs
RDMA/cma: Only call cma_save_ib_info() for CM REQs
RDMA/cma: Fix accessing invalid private data for UD
RDMA/cma: Fix gcc warning
Revert "RDMA/nes: Fix compilation error when nes_debug is enabled"
IB/qib: Add err_decode() call for ring dump
RDMA/cxgb3: Fix stack info leak in iwch_create_cq()
RDMA/nes: Fix info leaks in nes_create_qp() and nes_create_cq()
RDMA/ocrdma: Fix several stack info leaks
RDMA/cxgb4: Fix stack info leak in c4iw_create_qp()
RDMA/ocrdma: Remove unused include
This message was added in commit a7154cb8 (June 2004, [PATCH] r8169:
link handling and phy reset rework) and is printed every ten seconds
when no cable is connected and runtime power management is disabled.
(Before that commit, "Reset RTL8169s PHY" would be printed instead.)
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQF_DISABLED is a no-op by now and should be
removed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal #define to help grep find mac addresses
and ensure that addresses are aligned.
pasemi.h has an unaligned access to mac_addr, unchanged
for now.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Olof Johansson <olof@lixom.net> # pasemi_mac pieces
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver firmware mailbox interface was operating in polling mode
because of limitations with the earlier versions of 83xx adapter firmware.
These issues are resolved and we are implementing interrupt based mailbox
mechanism.
o Data structures and API's for interrupt mode mailbox mechanism.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enhanced the driver to use standard Linux error codes
o Return a unique error code to indicate loopback is in progress
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On very rare occasions, repeated load/unload stress test in the presence of
our storage driver (bnx2i/bnx2fc) causes a kernel panic in bnx2x code
(NULL pointer dereference). Stack traces indicate the issue happens during MAC
configuration; thorough code review showed that indeed several races exist
in which one thread can iterate over the list of configured MACs while another
deletes entries from the same list.
This patch adds a varient on the single-writer/Multiple-reader lock mechanism -
It utilizes an already exsiting bottom-half lock, using it so that Whenever
a writer is unable to continue due to the existence of another writer/reader,
it pends its request for future deliverance.
The writer / last readers will check for the existence of such requests and
perform them instead of the original initiator.
This prevents the writer from having to sleep while waiting for the lock
to be accessible, which might cause deadlocks given the locks already
held by the writer.
Another result of this patch is that setting of Rx Mode is now made in
sleepable context - Setting of Rx Mode is made under a bottom-half lock, which
was always nontrivial for the bnx2x driver, as the HW/FW configuration requires
wait for completions.
Since sleep was impossible (due to the sleepless-context), various mechanisms
were utilized to prevent the calling thread from sleep, but the truth was that
when the caller thread (i.e, the one calling ndo_set_rx_mode()) returned, the
Rx mode was still not set in HW/FW.
bnx2x_set_rx_mode() will now overtly schedule for the Rx changes to be
configured by the sp_rtnl_task which hold the RTNL lock and is sleepable
context.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slaves get the 64B CQE/EQE state from QUERY_HCA, not from the module parameter.
If the parameter is set to zero, the slave outputs an incorrect/irrelevant
warning message that 64B CQEs/EQEs are supported but not enabled (even if the
hypervisor has enabled 64B CQEs/EQEs).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user has not assigned a MAC address to a VM, then don't give it MAC which
is based on the PF one. The current derivation scheme is wrong and leads to VM
MAC collisions when the number of cards/hypervisors becomes big enough.
Instead, just give it zeros and let them figure out what to do with that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial driver support was for a single mPIPE shim on the chip
(as is the case for the Gx36 hardware). The Gx72 chip has two mPIPE
shims, so we extend the driver to handle that case.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code used to call napi_disable() in an interrupt handler
(from smp_call_function), which in turn could call msleep().
Unfortunately you can't sleep in an interrupt context.
Luckily it turns out all the NAPI support functions are
just operating on data structures and not on any deeply
per-cpu data, so we can arrange to set up and tear down all
the NAPI state on the core driving the process, and just
do the IRQ enable/disable as a smp_call_function thing.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building against headers from an older Tilera hypervisor can cause
the frags[] array to be overrun. Don't enable TSO in that case.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the user to configure various features of the tile
networking drivers on and off. There is no change to the default
initialization state of either the tilegx or tilepro drivers.
Neither driver needs the ndo_fix_features or ndo_set_features callbacks,
since the generic code already handles the dependencies for
fix_features, and there is no hardware state to tweak in set_features.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
grp->grp_id is obsolete. It has no use in the current driver.
Remove it from gfar_priv_grp and put the 'rstat' member
in its place, in the 2nd cache line, as rstat needs fast access.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self explanitory dma_mapping_error addition to the 8139 driver, based on this:
https://bugzilla.redhat.com/show_bug.cgi?id=947250
It showed several backtraces arising for dma_map_* usage without checking the
return code on the mapping. Add the check and abort the rx/tx operation if its
failed. Untested as I have no hardware and the reporter has wandered off, but
seems pretty straightforward.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RFE interrupt is enabled for the r8a7790 but isn't handled,
resulting in the interrupts core noticing unhandled interrupts, and
eventually disabling the ethernet IRQ.
Fix it by adding RFE to the bitmask of error interrupts to be handled
for r8a7790.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce enbale_hca and disable_hca commands to signify when the
driver starts or ceases to operate on the device.
In addition the driver will use boot and init pages count; boot pages
is required to allow firmware to complete boot commands and the other
to complete init hca. Command interface revision is bumped to 4 to
enforce using supported firmware.
This patch breaks compatibility with old versions of firmware (< 4);
however, the first GA firmware we will publish will support version 4
so this should not be a problem.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
We can't dereference "ent" after passing it to free_cmd().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Jeff Kirsher says:
====================
This series contains updates to ixgbe and pci.
The first patch for ixgbe from Greg Rose is the second submission. The
first submission of "ixgbe: Retain VLAN filtering in promiscuous + VT
mode" had a typo, which Joe Perches pointed out and is fixed in this
submission.
Alex updates the ixgbe driver to use the generic helper pci_vfs_assigned
instead of the driver specific function ixgbe_vfs_are_assigned.
Don Skidmore provides 4 patches for ixgbe, the first being a fix for
flow control ethtool reporting. Originally ixgbe_device_supports_autoneg_fc()
was expected to be called by only copper devices, which lead to false
information being displayed via ethtool. Two other patches add support
for fixed fiber for SFP+ devices and the addition of a quad-port x520
adapter. The last patch simply bumps the driver version.
Emil Tantilov provides 3 fixes for ixgbe, two of which resolve
semaphore lock issues. The third fix resolves several issues in the
previous implementation of the SFF data dumps of SFP+ modules.
The remaining ixgbe and pci patches are from Jacob Keller. The pci
patches exposes bus speed, link speed and bus width so that drivers
can take advantage of this information. In addition, adds a pci function
which obtains minimum link width and speed. Jacob also provides the
ixgbe patch to incorporate the pci function. He provides a patch that
fixes a lockdep issue created due to ixgbe_ptp_stop always running
cancel_work_sync even if the work item had not been created properly with
INIT_WORK. This issue was found and reported by Stephen Hemminger.
-v2-
* fix patch 3 to be a bool function based on David Miller's feedback
* fix patch 4 debug message based on David Miller's feedback
* fix patch 8 moved the extern declarations to pci.h based on Bjorn
Helgaas's feedback
* fix patch 11 update the error message to include encoding loss based
* fix patch 8/9/10 title based on Bjorn's feedback
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a x520 based quad-port (4x10Gbps) NIC with a single QSFP+
connector. Changes were required to our identify functions due to
different eeprom address which is also included here.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the error code path in ixgbe_acquire_swfw_sync() to deal
with cases where acquiring SW semaphore times out.
In cases where the SW/FW semaphore bits were set (i.e. due to a crash) the
driver will hang on load. With this patch the driver will clear
the stuck bits if the semaphore was not acquired in the allotted time.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch renames the stats introduced by the busy poll feature so that they
are more inline with the current statistics naming schemes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a lockdep issue created due to ixgbe_ptp_stop always running
cancel_work_sync even if the work item had not been created properly with
INIT_WORK. This is caused because ixgbe_ptp_stop did not check to actually
ensure PTP was running first. The new implementation introduces a state in the
&adapter->state field which is used to indicate that PTP is running. (This
replaces the IXGBE_FLAG2_PTP_ENABLED field). This state will use the atomic
set_bit, test_bit, and test_and_clear_bit functions. ixgbe_ptp_stop will check
to ensure that PTP was enabled, (and if not, it will not attempt to do any
cleanup work from ixgbe_ptp_init). This resolves the lockdep annotation warning
found by Stephen Hemminger
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch uses the new pcie_get_minimum_link function to perform a check to
ensure that the adapter is hooked into a slot which is capable of providing the
necessary bandwidth. This check supersedes the original method which only
checked the current pci device. The new method is capable of determining the
minimum speed and link of an entire PCI chain.
-v2-
* update the error message to include encoding loss
CC: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix to return -ENOMEM from the ioremap error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mvneta driver is compiled as module, the clock is disabled before
it's loading. This will reset the registers values and all configuration
made by the bootloader.
This patch sets the "sgmii serdes configuration" register to a magical value
found in:
https://github.com/yellowback/ubuntu-precise-armadaxp/blob/master/arch/arm/mach-armadaxp/armada_xp_family/ctrlEnv/mvCtrlEnvLib.c
With this change, the interrupts are working/generated and ethernet is
working.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mvneta driver is compiled, it'll be loaded with clocks disabled.
This implies that the clocks should be enabled again before any register
access or it'll hang.
To fix it:
- enable clock earlier
- move timer callback after setting timer.data
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Mon, 2013-07-29 at 08:30 -0700, Eric Dumazet wrote:
> On Mon, 2013-07-29 at 13:09 +0100, Luis Henriques wrote:
>
> >
> > I confirm that I can't reproduce the issue using this patch.
> >
>
> Thanks, I'll send a polished patch, as this one had an error if
> build_skb() returns NULL (in case sk_buff allocation fails)
Please try the following patch : It should use 2K frags instead of 4K
for normal 1500 mtu
Thanks !
[PATCH] atl1c: use custom skb allocator
We had reports ( https://bugzilla.kernel.org/show_bug.cgi?id=54021 )
that using high order pages for skb allocations is problematic for atl1c
We do not know exactly what the problem is, but we suspect that crossing
4K pages is not well supported by this hardware.
Use a custom allocator, using page allocator and 2K fragments for
optimal stack behavior. We might make this allocator generic
in future kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Luis Henriques <luis.henriques@canonical.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes several issues with the previous implementation of the
SFF data dump of SFP+ modules:
- removed the __IXGBE_READ_I2C flag - I2C access locking is handled in the
HW specific routines
- fixed the read loop to read data from ee->offset to ee->len
- the reads fail if __IXGBE_IN_SFP_INIT is set in the process - this is
needed because on some HW I2C operations can take long time and disrupt
the SFP and link detection process
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe_read/write_i2c_phy_82598() does not hold the SWFW_SYNC
semaphore for the entire function. Instead the lock is held only
during the phy.ops.read/write_reg operations. As result when the
function is being called simultaneously the I2C read/writes can
be corrupted.
The following patch introduces the SWFW_SYNC semaphore for the
entire ixgbe_read/write_i2c_phy_82598() function. To accomplish
this I had to create 2 separate functions:
ixgbe_read_phy_reg_mdi()
ixgbe_write_phy_reg_mdi()
Those functions are identical to ixgbe_read/write_phy_reg_generic()
sans the locking, and can be used in ixgbe_read/write_i2c_phy_82598()
with the SWFW_SYNC semaphore being held.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Bump the version number to better match with a similar version of the
out of tree driver.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for a new media type fiber_fixed. This is useful
to avoid all the SFP+ hot plug support path on devices who's fix fiber need
not worry about such things. This patch is needed for a following patch
that adds support for "fiber_fixed" devices.
v2: cleaned up logging message based on feedback from David Miller
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Originally ixgbe_device_supports_autoneg_fc() was only expected to
be called by copper devices. This would lead to false information
to be displayed via ethtool.
v2: changed ixgbe_device_supports_autoneg_fc() to a bool function,
it returns bool. Based on feedback from David Miller
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that the ixgbe driver uses the generic helper
pci_vfs_assigned instead of the ixgbe specific function
ixgbe_vfs_are_assigned.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When using the new bridge FDB interface to allow SR-IOV virtual function
network devices to communicate with SW bridged network devices the
physical function is placed into promiscuous mode and hardware VLAN
filtering is disabled. This defeats the ability to use VLAN tagging
to isolate user networks. When the device is in promiscuous mode and
VT mode simultaneously ensure that VLAN hardware filtering remains
enabled.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the "swap descriptor" feature of the hardware to properly swap the
descriptors when running in big endian mode. Since the swapping occurs
on 64 bits words, we also need to provide a separate structure layout
for the DMA descriptors between little endian and big endian mode,
like is done in the mv643xx_eth driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macros used for the various fields of the RX and TX descriptions
are currently declared next to those fields within the structure
definitions of the RX and TX descriptors.
However, in order to support big endian, we'll have to use the "swap
descriptors" features of the hardware, which swaps every byte within
each 64 bits word of the descriptors. This requires a separate
definition of the RX and TX descriptor structures for little and big
endian, as is done in the mv643xx_eth. Those macros can therefore no
longer be defined inside those structures.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for setting MAC address to cpsw device via ndo_set_mac_address
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't test for having link and let hardware deal with this situation.
Without this patch I see a machine running an -rt patched Linux being
stuck in sch_direct_xmit when it looses link while there is still a
packet to be sent. In this case the fec_enet_start_xmit routine returned
NETDEV_TX_BUSY which makes the network stack reschedule the packet and
so sch_direct_xmit calls fec_enet_start_xmit again.
I failed to reproduce a complete hang without -rt, but I think the
problem exists there, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses dev_err when enabling of AER fails (e.g. PCIe AER is not
supported). The dev_info is more appropriate to avoid console pollution.
Cc: sathya.perla@emulex.com
Cc: subbu.seetharaman@emulex.com
Cc: ajit.khaparde@emulex.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5762 devices sometimes incorrectly treat udp fragments as RMCP
packets and route to the APE. This patch sets the RX_MODE_IPV4_FRAG_FIX
bit for these devices which enables the proper behaviour.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP_CAPABLE tg3 devices have a gpio output that is toggled when the
free running counter matches a watchdog value. This patch adds support
to set the watchdog and enable this feature.
Since the output is controlled via bits in the EAV_REF_CLCK_CTL
register, we have to read-modify-write it when we stop/resume.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove the call to tg3_power_down_prepare() in tg3_power_down()
since tg3_close() calls it.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when the interface was brought down, the driver would set
the power state to D3hot. In D3hot, we don't have access to the NVRAM.
This patch removes the call to set the power state to PCI_D3hot in
close. A following patch will implement the shutdown handler to properly
set the D3hot state when the system is going down.
Doing the above means that the TG3_PHYFLG_IS_LOW_POWER should not be
checked to validate access to the NVRAM.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During probe, the driver is incorrectly switching the power to Vaux on
the 5717 and later devices. At this point, we are in D0 state and
drawing maximum power. We also definitely have Vmain available. It
doesn't make sense to switch to Vaux since it has a lesser maximum power
draw and we might go over the limit. On a new system, we observe that
not all ports are recognized in some of the slots with this call in
place.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion status field should also be checked for non-zero error
condition.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update TCP delayed ACK and timestamp options setup to match latest bnx2x
firmware.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without resetting it, the bnx2i driver cannot use different options for
different iSCSI connections.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since unregister_netdevice_notifier() will replay the NETDEV_DOWN and
NETDEV_UNREGISTER_EVENTS, the cnic_dev_list will be cleaned up automatically.
The loop to cleanup the cnic_dev_list can be removed in cnic_release().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After this earlier commit to simplify probing:
commit 4bd9b0fffb
cnic, bnx2x, bnx2: Simplify cnic probing.
we can now reliably receive netdev events and we can simplify the handling
of these events. We now remove the logic that tries to handle missed
NETDEV_REGISTER events.
This change will allow cleanup to be simplified in the next patch. We can
now rely on the play back of netdev events during
unregister_netdevice_notifier() to cleanup the structures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds new firmware command and new firmware event. The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.
Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a race between BlueFlame flow and stamping in post send flow.
Example:
SW: Build WQE 0 on the TX buffer, except the ownership bit
SW: Set ownership for WQE 0 on the TX buffer
SW: Ring doorbell for WQE 0
SW: Build WQE 1 on the TX buffer, except the ownership bit
SW: Set ownership for WQE 1 on the TX buffer
HW: Read WQE 0 and then WQE 1, before doorbell was rung/BF was done for WQE 1
HW: Produce CQEs for WQE 0 and WQE 1
SW: Process the CQEs, and stamp WQE 0 and WQE 1 accordingly (on the TX buffer)
SW: Copy WQE 1 from the TX buffer to the BF register - ALREADY STAMPED!
HW: CQE error with index 0xFFFF - the BF WQE's control segment is STAMPED,
so the BF index is 0xFFFF. Error: Invalid Opcode.
As a result QP enters the error state and no traffic can be sent.
Solution:
When stamping - do not stamp last completed wqe.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a VT mode check to make sure VLAN filters are disabled when
in promisc mode and VT is not enabled.
The problem with the previous check was that:
E1000_MRQC_ENABLE_VMDQ is defined as 0x00000003
but when not in VT mode:
mrqc |= E1000_MRQC_ENABLE_RSS_4Q (0x00000002)
So the above check will trigger regardless if VT mode is being used or not.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue with the 82598EB device, where lldpad is causing Tx
Hangs on the card as soon as it attempts to configure DCB for the device. The
adapter will continually Tx hang and reset in a loop.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Stable <stable@vger.kernel.org>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initialization of the PHY on I217/I218, while similar to 82579, must
also check to see if the MAC and PHY are in the same mode (PCIe vs. SMBus)
otherwise the PHY will be inaccessible by the MAC.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the device is runtime suspended (e.g. when there is no link), do not
wake it from D3 to read the PHY status; just set the values to typical
power-on defaults as is done when runtime PM is not enabled and there is no
link.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device IDs 0x15a0 and 0x15a1 are new SKUs that contain the same MAC as
I217 and same PHY as I218.
The device IDs 0x15a2 and 0x15a3 are the same as existing I218 SKUs.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous patch (commit e60b22c5b7 e1000e: fix accessing to suspended
device) added .begin and .complete ethtool driver callbacks so that the
device was resumed from Runtime Power Management (RPM) suspend state for
all ethtool operations. This is overkill for operations which do not need
to access any registers in the device. This patch makes it so that the
device is taken out of RPM suspend only for those ethtool operations that
must access device registers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tx hang is an unintended consequence of another workaround that is in the
EEPROM for an issue with the firmware at 10Mbps when K1 (a power mode of
the MAC-PHY interconnect) is enabled. The issue is resolved by setting
appropriate Tx re-transmission timeouts in the PHY and associated K1 entry
times in the MAC to allow enough transmissions to occur without triggering
a Tx hang. A similar change is needed when linked at 10Mbps to improve
latency.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Alter the packet buffer allocation accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The jumbo frame configuration in the MAC/PHY should be reverted on 82579
and newer parts when the interface is brought down (not just when the MTU
is changed back to standard frame size) otherwise iAMT connections (e.g.
SoL, IDE-R) will be dropped and cannot be re-acquired until the MTU is
changed again.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82583 can disappear off the PCIe bus. This device is a modified 82574
which had the same problem which was fixed by disabling ASPM L1; disabling
it on 82583 fixes the issue on this device.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In structure e1000_rx_desc_packet_split, the size of wb.upper.length is
defined by a digit. This may introduce some problem when the length is
changed.
This patch use the macro PS_PAGE_BUFFERS for the definition. And move the
definition to hw.h.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
tx_ring/rx_ring size is assigned in function e1000_alloc_queues(), which is
called by e1000_sw_init() in the early stage of e1000_probe().
This patch just remove the duplicate assignment of this default ring size
value.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Da Yu Qiu <qiudayu@cn.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In attempting to resolve a minor merge conflict, commit e5f2ef7ab4
(Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net) accidentally
dropped a call to pci_clear_master() that was intended to remain in place.
Commit 4e0855dff0 (e1000e: fix pci-device enable-counter balance)
replaced a call to pci_disable_device() by one to pci_clear_master(). And then
commit 66148babe7 (e1000e: fix runtime power management transitions)
deleted a number of lines starting two lines following that call.
This patch restores the call to pci_clear_master() in __e1000_shutdown().
v2: added summary lines (enclosed in parens) following commit IDs
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Darren Hart says:
====================
Add support for the MinnowBoard in the pch_gbe driver. This was
originally sent to LKML as part of the MinnowBoard support series. That
is now partially merged and this version of the patch has been isolated
from those changes and is now completely self-contained.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If the ready bit in the transmit buffer descriptor (TxBD[R])
is previously detected as not set during a prior frame transmission,
then the ENET_TDAR[TDAR] bit is cleared at a later time, even if
additional TxBDs were added to the ring and the ENET_TDAR[TDAR]
bit is set. This results in frames not being transmitted until
there is a 0-to-1 transition on ENET_TDAR[TDAR].
Workarounds:
code can use the transmit frame interrupt flag (ENET_EIR[TXF])
as a method to detect whether the ENET has completed transmission
and the ENET_TDAR[TDAR] has been cleared. If ENET_TDAR[TDAR] is
detected as cleared when packets are queued and waiting for transmit,
then a write to the TDAR bit will restart TxBD processing.
This case main happen when loading is light. A ethernet package may
not send out utile next package put into tx queue.
How to test:
while [ true ]
do
ping <IP> -s 10000 -w 4
ping <IP> -s 6000 -w 2
ping <IP> -s 4000 -w 2
ping <IP> -s 10000 -w 2
done
You will see below result in overnight test.
6008 bytes from 10.192.242.116: seq=1 ttl=128 time=0.722 ms
4008 bytes from 10.192.242.116: seq=0 ttl=128 time=1001.008 ms
4008 bytes from 10.192.242.116: seq=1 ttl=128 time=1.010 ms
10008 bytes from 10.192.242.116: seq=0 ttl=128 time=0.896 ms
After apply this patch, >1000ms delay disappear.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Initialize proper interrupt handler for 83xx.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When configuring guest VLAN after PVID configuration, VF was loading
with previously configured PVID. Clear the PVID which was previously
configured before configuring guest VLAN.
o Display guest VLAN when it is configured
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Operation type and command type is not set correct in back channel
response.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work function needs to be initialized before we participate in
inter device communication (IDC).
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ebe7fdbaf3.
This change is not correct. GFP_DMA is not necessary for
this device.
There is some other problem causing this bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
atl1c uses netdev_alloc_skb to refill its rx dma ring, but that call makes no
guarantees about the suitability of the memory for use in DMA. As a result
we've gotten reports of atl1c drivers occasionally hanging and needing to be
reset:
https://bugzilla.kernel.org/show_bug.cgi?id=54021
Fix this by modifying the call to use the internal version __netdev_alloc_skb,
where you can set the gfp_mask explicitly to include GFP_DMA.
Tested by two reporters in the above bug, who have the hardware to validate it.
Both report immediate cessation of the problem with this patch
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: stable@vger.kernel.org
Tested-by: Luis Henriques <luis.henriques@canonical.com>
Tested-by: Vincent Alquier <vincent.alquier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While EEH error happens, we might not have network device instance
(struct net_device) yet. So we can't access the instance safely and
check its link state, which causes kernel crash. The patch fixes it.
EEH: Frozen PE#2 on PHB#3 detected
EEH: This PCI device has failed 1 times in the last hour
EEH: Notify device drivers to shutdown
(NULL net_device): PCI I/O error detected
Unable to handle kernel paging request for data at address 0x00000048
Faulting instruction address: 0xd00000001c9387a8
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=1024 NUMA PowerNV
:
NIP [d00000001c9387a8] .tg3_io_error_detected+0x78/0x2a0 [tg3]
LR [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
Call Trace:
[c000003f93a0f960] [d00000001c9387a4] .tg3_io_error_detected+0x74/0x2a0 [tg3]
[c000003f93a0fa30] [c00000000003844c] .eeh_report_error+0xac/0x120
[c000003f93a0fac0] [c0000000000371bc] .eeh_pe_dev_traverse+0x8c/0x150
[c000003f93a0fb60] [c000000000038858] .eeh_handle_normal_event+0x128/0x3d0
[c000003f93a0fbf0] [c000000000038db8] .eeh_handle_event+0x2b8/0x2c0
[c000003f93a0fc90] [c000000000038e80] .eeh_event_handler+0xc0/0x170
[c000003f93a0fd30] [c0000000000cc000] .kthread+0xf0/0x100
[c000003f93a0fe30] [c00000000000a0dc] .ret_from_kernel_thread+0x5c/0x80
Reported-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Acked-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAC driver can't work without its associated PHY driver. Reflect
this in the Kconfig options by selecting it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MinnowBoard uses an AR803x PHY with the PCH GBE which requires
special handling. Use the MinnowBoard PCI Subsystem ID to detect this
and add a pci_device_id.driver_data structure and functions to handle
platform setup.
The AR803x does not implement the RGMII 2ns TX clock delay in the trace
routing nor via strapping. Add a detection method for the board and the
PHY and enable the TX clock delay via the registers.
This PHY will hibernate without link for 10 seconds. Ensure the PHY is
awake for probe and then disable hibernation. A future improvement would
be to convert pch_gbe to using PHYLIB and making sure we can wake the
PHY at the necessary times rather than permanently disabling it.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Joe Perches <joe@perches.com>
Cc: netdev@vger.kernel.org
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using magic numbers when we have perfectly good defines just lying
around.
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Waskiewicz <peter.p.waskiewicz.jr@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: netdev@vger.kernel.org
Add support to show CPSW hardware statistics to user via ethtool
so user can find if there were any error reported by hardware or
the system is over loaded duing high data rate transfer.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves all enic ethtool hooks from enic_main.c to a new file
enic_ethtool.c
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't dereference "ent" after passing it to free_cmd().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The work queue is initialised in rtl_open (when the interface goes up),
but canceled in rtl_remove_one (when the PCI device gets removed). If
the network interface is not brought up, then the work queue struct is
not initialised. When the device is removed, the attempt to cancel the
uninitialised work queue causes a lockdep warning.
This patch fixes the issue by moving cancel_work_sync to rtl_close (to
match rtl_open). (Note that rtl_close is also called via
unregister_netdev in rtl_remove_one.)
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the UC-list is being deleted from the HW MAC table, but the primary
MAC is not.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SH-R and Lancer-R, GET_MAC_LIST cmd is better supported
(instead of NTWK_MAC_QUERY cmd) to query provisioned MAC addresses.
Similiarly, (on SH-R and Lancer-R) SET_MAC_LIST must be used by the PF to
provision a permanent MAC addresses to the VF.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to configure the permanent MAC in be_setup() has become quite
complicated, with different FW cmds being used for BEx, SH-R and Lancer.
Simplify the logic by moving some of this complexity to be_cmds.c. This
makes the code in be_setup() a little more readable.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For BE3 VFs, the permanent MAC is added by its PF. The VF can retrieve its
pmac_id only via the IFACE_CREATE cmd. This is not true for Lancer and SH-R
VFs which get the pmac_id by issuing a ADD_IFACE_MAC cmd. So, use this
hack only for BE3 VFs.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current design VFs were not allowed to program MAC/VLAN filters.
Only the PF driver was allowed to configure/provision MAC and transparent
VLANs to a VF. Change this to support MAC/VLAN filtering on a VF by a VM.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the VFs by default don't have the privilege to modify MAC address.
This will change in a subsequent fix wherein VFs will have the ability to
modify MAC/VLAN filters.
Fix be_mac_addr_set() logic to support MAC address modification on a
privileged VF too.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a copy of support for r8a7778/9 with the .rmiimode mode bit
of struct sh_eth_cpu_data set.
Also update R8A7779 to R8A777x.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is prsent on the r8a7790 SoC.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac uses bcm47xx_nvram.h which is only available when BCM47XX was
selected. Earlier BCMA_HOST_SOC depended on BCM47XX so this was not
build on any other archs, but that changed. We should modify this
driver to get access to the nvram or the variables through platform
data.
This fixes a build problem in linux-next reported by Stephen Rothwell:
drivers/net/ethernet/broadcom/bgmac.c:19:27: fatal error: bcm47xx_nvram.h: No such file or directory
#include <bcm47xx_nvram.h>
^
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add MODULE_ALIAS, so that auto module loading can work.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Received packets are only scattered if this is enabled in both the
matching filter and the receiving queue. This was not being done for
filters inserted for RFS, so any packet requiring more than a single
descriptor was dropped.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using devm_request_irq() can make the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As devm_ioremap_resource() is used, there is no need to explicitely check the
return value from platform_get_resource(), as this is something that
devm_ioremap_resource() takes care by itself.
Also, place platform_get_resource() prior to devm_ioremap_resource() for
better code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_ptp should also be enabled in fec_resume() and disabled in fec_suspend().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On fec_probe the clocks are enabled in the following order:
clk_ahb -> clk_ipg -> clk_enet_out -> clk_ptp
, so in the error and remove paths we should disabled them in the opposite
order.
Also fix the order in the suspend/resume functions.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_enet_out and clk_ptp are optional clocks, so we should not enable/disable
them unconditionally.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4bb1667255 (build some drivers only
when compile-testing), PTP_1588_CLOCK_PCH depends on (X86 ||
COMPILE_TEST). But PCH_GBE selects PTP_1588_CLOCK_PCH without
depending on x86. Fix this by adding the same dependency here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: <fengguang.wu@intel.com> [intel's build test robot]
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: kbuild-all@01.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Add poll controller function for velocity nic.
Signed-off-by: Amit Uttamchandani <auttamchandani@logicube.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Clear cached vport vlan variable(vp->vlan) in PF on PCI FLR and
back-channel termination which will allow to configure guest VLAN
on VF after force off/shut down the guest VM.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was using wrong mask for template version.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Commit b938662d88
("qlcnic: Fix ethtool supported port status for 83xx")
introduced regression for display of link status for 83xx
adapter while refactoring port status display. This patch
is to fix the link status display for 83xx adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o "qlcnic_sriov" structure pointer should be accessed only
when SR-IOV is enabled. Access this pointer after SR-IOV
PF check.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Multicast MAC was not getting programmed due to which multicast
packets were being dropped by FW.
This patch fixes commit 168e4fb54c11865668ad50eff81b5f2729e0e0f4
("qlcnic: Secondary unicast MAC address support.") which introduced
bug in handling multicast packets.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Check for non-NULL set_mac_filter_count function pointer
before calling it fixes the panic.
This patch fixes regression introduced by patch
"qlcnic: Secondary unicast MAC address support." with
commit id 168e4fb54c11865668ad50eff81b5f2729e0e0f4.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI poll function does not re-enable the interrupt, if __QLCNIC_DEV_UP is not set
in adapter state. This was preventing driver from receiving any packet.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx adapter specific code was accessing 82xx register which
resulted in invalid register offset. This patch uses proper
register access method.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware workaround requesting hardware to skip vlan insertion is necessary
only when umc or qnq is enabled. Enabling this workaround in other scenarios
could cause controller to stall.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bgmac is using functions from phylib, add the dependency.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings pointed out that my recent update to atl1e
in commit 352900b583
("atl1e: fix dma mapping warnings") was missing a bit of code.
Specifically it reset the hardware tx ring to its origional state when
we hit a dma error, but didn't unmap any exiting mappings from the
operation. This patch fixes that up. It also remembers to free the
skb in the event that an error occurs, so we don't leak. Untested, as
I don't have hardware. I think its pretty straightforward, but please
review closely.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Ben Hutchings <bhutchings@solarflare.com>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Just a bunch of small fixes and tidy ups:
1) Finish the "busy_poll" renames, from Eliezer Tamir.
2) Fix RCU stalls in IFB driver, from Ding Tianhong.
3) Linearize buffers properly in tun/macvtap zerocopy code.
4) Don't crash on rmmod in vxlan, from Pravin B Shelar.
5) Spinlock used before init in alx driver, from Maarten Lankhorst.
6) A sparse warning fix in bnx2x broke TSO checksums, fix from Dmitry
Kravkov.
7) Dummy and ifb driver load failure paths can oops, fixes from Tan
Xiaojun and Ding Tianhong.
8) Correct MTU calculations in IP tunnels, from Alexander Duyck.
9) Account all TCP retransmits in SNMP stats properly, from Yuchung
Cheng.
10) atl1e and via-rhine do not handle DMA mapping failures properly,
from Neil Horman.
11) Various equal-cost multipath route fixes in ipv6 from Hannes
Frederic Sowa"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (36 commits)
ipv6: only static routes qualify for equal cost multipathing
via-rhine: fix dma mapping errors
atl1e: fix dma mapping warnings
tcp: account all retransmit failures
usb/net/r815x: fix cast to restricted __le32
usb/net/r8152: fix integer overflow in expression
net: access page->private by using page_private
net: strict_strtoul is obsolete, use kstrtoul instead
drivers/net/ieee802154: don't use devm_pinctrl_get_select_default() in probe
drivers/net/ethernet/cadence: don't use devm_pinctrl_get_select_default() in probe
drivers/net/can/c_can: don't use devm_pinctrl_get_select_default() in probe
net/usb: add relative mii functions for r815x
net/tipc: use %*phC to dump small buffers in hex form
qlcnic: Adding Maintainers.
gre: Fix MTU sizing check for gretap tunnels
pkt_sched: sch_qfq: remove forward declaration of qfq_update_agg_ts
pkt_sched: sch_qfq: improve efficiency of make_eligible
gso: Update tunnel segmentation to support Tx checksum offload
inet: fix spacing in assignment
ifb: fix oops when loading the ifb failed
...
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
- AF_IB (native IB addressing) for CMA from Sean Hefty
- New mlx5 driver for Mellanox Connect-IB adapters (including post merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- Resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- Other small changes and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nZh8
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- AF_IB (native IB addressing) for CMA from Sean Hefty
- new mlx5 driver for Mellanox Connect-IB adapters (including post
merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- other small changes and fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
mlx5: Return -EFAULT instead of -EPERM
IB/qib: Log all SDMA errors unconditionally
IB/qib: Fix module-level leak
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
IB/uverbs: Use get_unused_fd_flags(O_CLOEXEC) instead of get_unused_fd()
mlx5_core: Fixes for sparse warnings
IB/mlx5: Make profile[] static in main.c
mlx5: Fix parameter type of health_handler_t
mlx5: Add driver for Mellanox Connect-IB adapters
IB/core: Add reserved values to enums for low-level driver use
IB/srp: Bump driver version and release date
IB/srp: Make HCA completion vector configurable
IB/srp: Maintain a single connection per I_T nexus
IB/srp: Fail I/O fast if target offline
IB/srp: Skip host settle delay
IB/srp: Avoid skipping srp_reset_host() after a transport error
IB/srp: Fix remove_one crash due to resource exhaustion
IB/qib: New transmitter tunning settings for Dell 1.1 backplane
IB/core: Fix error return code in add_port()
...
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For copy_to/from_user() failure, the correct error code is -EFAULT not
-EPERM.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Sparse reported an endianness bug in the assignment to hca_cap.uar_page_sz.
Fix the declaration of this field to be __be16 (which is what is in
the firmware spec), renaming the field to log_uar_pg_size to conform
to the spec, which fixes the endianness bug reported by sparse.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Since commit c957d09ffd
"bnx2x: Remove sparse and coccinelle warnings"
driver provided wrong partial csum for HW in tunneing
scenarios.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Pravin Shelar <pshelar@nicira.com>
CC: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Tested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move spin_lock_init to be called before the spinlocks are used, preventing a lockdep splat.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `sh_eth_free_dma_buffer':
drivers/net/ethernet/renesas/sh_eth.c:1103: undefined reference to `dma_free_coherent'
drivers/net/ethernet/renesas/sh_eth.c:1110: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `sh_eth_ring_init':
drivers/net/ethernet/renesas/sh_eth.c:1065: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/renesas/sh_eth.c:1086: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `sh_eth_ring_format':
drivers/net/ethernet/renesas/sh_eth.c:988: undefined reference to `dma_map_single'
drivers/built-in.o: In function `sh_eth_txfree':
drivers/net/ethernet/renesas/sh_eth.c:1220: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_eth_rx':
drivers/net/ethernet/renesas/sh_eth.c:1323: undefined reference to `dma_map_single'
drivers/built-in.o: In function `sh_eth_start_xmit':
drivers/net/ethernet/renesas/sh_eth.c:1954: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename ndo_ll_poll to ndo_busy_poll.
Rename sk_mark_ll to sk_mark_napi_id.
Rename skb_mark_ll to skb_mark_napi_id.
Correct all useres of these functions.
Update comments and defines in include/net/busy_poll.h
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the file and correct all the places where it is included.
Signed-off-by: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The missing call to unregister_netdev() leaves the interface active
after the driver is unloaded by rmmod.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"This is a re-do of the net-next pull request for the current merge
window. The only difference from the one I made the other day is that
this has Eliezer's interface renames and the timeout handling changes
made based upon your feedback, as well as a few bug fixes that have
trickeled in.
Highlights:
1) Low latency device polling, eliminating the cost of interrupt
handling and context switches. Allows direct polling of a network
device from socket operations, such as recvmsg() and poll().
Currently ixgbe, mlx4, and bnx2x support this feature.
Full high level description, performance numbers, and design in
commit 0a4db187a9 ("Merge branch 'll_poll'")
From Eliezer Tamir.
2) With the routing cache removed, ip_check_mc_rcu() gets exercised
more than ever before in the case where we have lots of multicast
addresses. Use a hash table instead of a simple linked list, from
Eric Dumazet.
3) Add driver for Atheros CQA98xx 802.11ac wireless devices, from
Bartosz Markowski, Janusz Dziedzic, Kalle Valo, Marek Kwaczynski,
Marek Puzyniak, Michal Kazior, and Sujith Manoharan.
4) Support reporting the TUN device persist flag to userspace, from
Pavel Emelyanov.
5) Allow controlling network device VF link state using netlink, from
Rony Efraim.
6) Support GRE tunneling in openvswitch, from Pravin B Shelar.
7) Adjust SOCK_MIN_RCVBUF and SOCK_MIN_SNDBUF for modern times, from
Daniel Borkmann and Eric Dumazet.
8) Allow controlling of TCP quickack behavior on a per-route basis,
from Cong Wang.
9) Several bug fixes and improvements to vxlan from Stephen
Hemminger, Pravin B Shelar, and Mike Rapoport. In particular,
support receiving on multiple UDP ports.
10) Major cleanups, particular in the area of debugging and cookie
lifetime handline, to the SCTP protocol code. From Daniel
Borkmann.
11) Allow packets to cross network namespaces when traversing tunnel
devices. From Nicolas Dichtel.
12) Allow monitoring netlink traffic via AF_PACKET sockets, in a
manner akin to how we monitor real network traffic via ptype_all.
From Daniel Borkmann.
13) Several bug fixes and improvements for the new alx device driver,
from Johannes Berg.
14) Fix scalability issues in the netem packet scheduler's time queue,
by using an rbtree. From Eric Dumazet.
15) Several bug fixes in TCP loss recovery handling, from Yuchung
Cheng.
16) Add support for GSO segmentation of MPLS packets, from Simon
Horman.
17) Make network notifiers have a real data type for the opaque
pointer that's passed into them. Use this to properly handle
network device flag changes in arp_netdev_event(). From Jiri
Pirko and Timo Teräs.
18) Convert several drivers over to module_pci_driver(), from Peter
Huewe.
19) tcp_fixup_rcvbuf() can loop 500 times over loopback, just use a
O(1) calculation instead. From Eric Dumazet.
20) Support setting of explicit tunnel peer addresses in ipv6, just
like ipv4. From Nicolas Dichtel.
21) Protect x86 BPF JIT against spraying attacks, from Eric Dumazet.
22) Prevent a single high rate flow from overruning an individual cpu
during RX packet processing via selective flow shedding. From
Willem de Bruijn.
23) Don't use spinlocks in TCP md5 signing fast paths, from Eric
Dumazet.
24) Don't just drop GSO packets which are above the TBF scheduler's
burst limit, chop them up so they are in-bounds instead. Also
from Eric Dumazet.
25) VLAN offloads are missed when configured on top of a bridge, fix
from Vlad Yasevich.
26) Support IPV6 in ping sockets. From Lorenzo Colitti.
27) Receive flow steering targets should be updated at poll() time
too, from David Majnemer.
28) Fix several corner case regressions in PMTU/redirect handling due
to the routing cache removal, from Timo Teräs.
29) We have to be mindful of ipv4 mapped ipv6 sockets in
upd_v6_push_pending_frames(). From Hannes Frederic Sowa.
30) Fix L2TP sequence number handling bugs, from James Chapman."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1214 commits)
drivers/net: caif: fix wrong rtnl_is_locked() usage
drivers/net: enic: release rtnl_lock on error-path
vhost-net: fix use-after-free in vhost_net_flush
net: mv643xx_eth: do not use port number as platform device id
net: sctp: confirm route during forward progress
virtio_net: fix race in RX VQ processing
virtio: support unlocked queue poll
net/cadence/macb: fix bug/typo in extracting gem_irq_read_clear bit
Documentation: Fix references to defunct linux-net@vger.kernel.org
net/fs: change busy poll time accounting
net: rename low latency sockets functions to busy poll
bridge: fix some kernel warning in multicast timer
sfc: Fix memory leak when discarding scattered packets
sit: fix tunnel update via netlink
dt:net:stmmac: Add dt specific phy reset callback support.
dt:net:stmmac: Add support to dwmac version 3.610 and 3.710
dt:net:stmmac: Allocate platform data only if its NULL.
net:stmmac: fix memleak in the open method
ipv6: rt6_check_neigh should successfully verify neigh if no NUD information are available
net: ipv6: fix wrong ping_v6_sendmsg return value
...
enic_change_mtu_work() must call rtnl_unlock() on all exiting paths.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Christian Benvenuti <benve@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Cc: Neel Patel <neepatel@cisco.com>
Cc: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port number is only local to the ethernet block, not global, so
there can be two ethernet blocks both using the same port, like
kirkwood with both using port 0.
Fix this by using the array index offset for the allocated platform
devices as the id.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use be32_to_cpu() instead of cpu_to_be32() where appropriate.
- use proper accessors for pointers marked __iomem.
Signed-off-by: Roland Dreier <roland@purestorage.com>
The driver is comprised of two kernel modules: mlx5_ib and mlx5_core.
This partitioning resembles what we have for mlx4, except that mlx5_ib
is the pci device driver and not mlx5_core.
mlx5_core is essentially a library that provides general functionality
that is intended to be used by other Mellanox devices that will be
introduced in the future. mlx5_ib has a similar role as any hardware
device under drivers/infiniband/hw.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
[ Merge in coccinelle fixes from Fengguang Wu <fengguang.wu@intel.com>.
- Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit 2768935a46 ('sfc: reuse pages to avoid DMA mapping/unmapping
costs') did not fully take account of DMA scattering which was
introduced immediately before. If a received packet is invalid and
must be discarded, we only drop a reference to the first buffer's
page, but we need to drop a reference for each buffer the packet
used.
I think this bug was missed partly because efx_recycle_rx_buffers()
was not renamed and so no longer does what its name says. It does not
change the state of buffers, but only prepares the underlying pages
for recycling. Rename it accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some during
this cycle, but even going though my tree isn't a great fit. Ian
Campbell has prototyped splitting the bindings and .dtb files into a
separate repository. The plan is to migrate to using that sometime in
the next few kernel releases which should get rid of a lot of the churn
on binding docs and .dts files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=CndB
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree updates from Grant Likely:
"This branch contains the following changes:
- Removal of CONFIG_OF_DEVICE, it is always enabled by CONFIG_OF
- Remove #ifdef from linux/of_platform.h to increase compiler syntax
coverage
- Bug fix for address decoding on Bimini and js2x powerpc platforms.
- miscellaneous binding changes
One note on the above. The binding changes going in from all kinds of
different trees has gotten rather out of hand. I picked up some
during this cycle, but even going though my tree isn't a great fit.
Ian Campbell has prototyped splitting the bindings and .dtb files into
a separate repository. The plan is to migrate to using that sometime
in the next few kernel releases which should get rid of a lot of the
churn on binding docs and .dts files"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of: Fix address decoding on Bimini and js2x machines
of: remove CONFIG_OF_DEVICE
usb: chipidea: depend on CONFIG_OF instead of CONFIG_OF_DEVICE
of: remove of_platform_driver
ibmebus: convert of_platform_driver to platform_driver
driver core: move to_platform_driver to platform_device.h
mfd: DT bindings for the palmas family MFD
ARM: dts: omap3-devkit8000: fix NAND memory binding
of/base: fix typos
of: remove #ifdef from linux/of_platform.h
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds dt support to dwmac version 3.610 and 3.710 these
versions are integrated in STiH415 and STiH416 ARM A9 SOCs.
To support these IP version, some of the device tree properties are
extended.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some DT use-cases platform data might be already allocated and passed
via AUXDATA. These are the cases where machine level code populates few
callbacks in the platform data.
This patch adds check and reuses platform_data if its valid, before
allocating a new one.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a memory leak in the open method, it reviews error
conditions freeing the resources previously allocated and not freed in
cased of DMA failure.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
"work" needs to be freed before returning on this error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables the driver to take advantage of the FEC VLAN
indicator to improve performance.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, WoL is broken and the system will immediately
resume after suspending, and I can't seem to figure out why.
Remove WoL support until the issue can be found.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
- A large slew of improvements of the Genric pin configuration
support, and deployment in four different platforms:
Rockchip, Super-H PFC, ABx500 and TZ1090. Support BIAS_BUS_HOLD,
get device tree parsing and debugfs support into shape.
- We also have device tree support with generic naming conventions
for the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now
handled in the device core: "sleep" and "idle", removing a lot
of boilerplate code in drivers. We do not yet know if this is
the final word for pin PM, but it already make things a lot
easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where
several pins are managed by a single register, and augment it to
handle sleep modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=EbAf
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control changes from Linus Walleij:
- A large slew of improvements of the Genric pin configuration support,
and deployment in four different platforms: Rockchip, Super-H PFC,
ABx500 and TZ1090. Support BIAS_BUS_HOLD, get device tree parsing
and debugfs support into shape.
- We also have device tree support with generic naming conventions for
the generic pin configuration.
- Delete the unused and confusing direct pinconf API. Now state
transitions is *the* way to control pins and multiplexing.
- New drivers for Rockchip, TZ1090, and TZ1090 PDC.
- Two pin control states related to power management are now handled in
the device core: "sleep" and "idle", removing a lot of boilerplate
code in drivers. We do not yet know if this is the final word for
pin PM, but it already make things a lot easier to handle.
- Handle sparse GPIO ranges passing a list of disparate pins, and
utilize these in the new BayTrail (x86 Atom SoC) driver.
- Make the sunxi (AllWinner) driver handle external interrupts.
- Make it possible for pinctrl-single to handle the case where several
pins are managed by a single register, and augment it to handle sleep
modes.
- Cleanups and improvements for the abx500 drivers.
- Move Sirf pin control drivers to their own directory, support
save/restore of context and add support for the SiRFatlas6 SoC.
- PMU muxing for the Dove pinctrl driver.
- Finalization and support for VF610 in the i.MX6 pinctrl driver.
- Smoothen out various Exynos rough edges.
- Generic cleanups of various kinds.
* tag 'pinctrl-for-v3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: vt8500: wmt: remove redundant dev_err call in wmt_pinctrl_probe()
pinctrl: remove bindings for pinconf options needing more thought
pinctrl: remove slew-rate parameter from tz1090
pinctrl: set unit for debounce time pinconfig to usec
pinctrl: more clarifications for generic pull configs
pinctrl: rip out the direct pinconf API
pinctrl-tz1090-pdc: add TZ1090 PDC pinctrl driver
pinctrl-tz1090: add TZ1090 pinctrl driver
pinctrl: samsung: Staticize drvdata_list
pinctrl: rockchip: Add missing irq_gc_unlock() call before return error
pinctrl: abx500: rework error path
pinctrl: abx500: suppress hardcoded value
pinctrl: abx500: factorize code
pinctrl: abx500: fix abx500_gpio_get()
pinctrl: abx500: fix abx500_pin_config_set()
pinctrl: abx500: Add device tree support
sh-pfc: Guard DT parsing with #ifdef CONFIG_OF
pinctrl: add Intel BayTrail GPIO/pinctrl support
pinctrl: fix pinconf_ops::pin_config_dbg_parse_modify kerneldoc
pinctrl: Staticize local symbols
...
Conflicts:
drivers/net/ethernet/ti/davinci_mdio.c
drivers/pinctrl/Makefile
Pull second set of VFS changes from Al Viro:
"Assorted f_pos race fixes, making do_splice_direct() safe to call with
i_mutex on parent, O_TMPFILE support, Jeff's locks.c series,
->d_hash/->d_compare calling conventions changes from Linus, misc
stuff all over the place."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
Document ->tmpfile()
ext4: ->tmpfile() support
vfs: export lseek_execute() to modules
lseek_execute() doesn't need an inode passed to it
block_dev: switch to fixed_size_llseek()
cpqphp_sysfs: switch to fixed_size_llseek()
tile-srom: switch to fixed_size_llseek()
proc_powerpc: switch to fixed_size_llseek()
ubi/cdev: switch to fixed_size_llseek()
pci/proc: switch to fixed_size_llseek()
isapnp: switch to fixed_size_llseek()
lpfc: switch to fixed_size_llseek()
locks: give the blocked_hash its own spinlock
locks: add a new "lm_owner_key" lock operation
locks: turn the blocked_list into a hashtable
locks: convert fl_link to a hlist_node
locks: avoid taking global lock if possible when waking up blocked waiters
locks: protect most of the file_lock handling with i_lock
locks: encapsulate the fl_link list handling
locks: make "added" in __posix_lock_file a bool
...
Prior this patch, the internal debugging was based on ifdef
and also some printk were useless because many info are exposed
via ethtool.
This patch remove all the ifdef defines and now we only use
netif_msg_XXX levels.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 38ae92d "fec: Add support for reading
RMON registers" causes the imx6Q to crash.
This fixes it by only enabling the RMON registers, the
registers are already cleared by the MAC being reset.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_bytes field was not being updated so the
network card statistics showed 0.0B transmitted.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x did not set dump->version in its .get_dump_flag() method.
Let's set it to BNX2X_DUMP_VERSION. It's not a particularly nice
number (0x50acff01 currently), but at least it's something
deterministic.
dump->flag should report the value previously set using ethtool -W.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x interprets the dump flag as an index of a register preset.
It is important to validate the index to avoid out of bounds
memory accesses.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to initialize the dump data with zeros.
data is allocated with vzalloc, so it's already zero-filled.
More importantly, the memset is harmful, because dump->len (the length
requested by userspace) can be bigger than the allocated buffer (whose
size is determined by asking the driver's .get_dump_flag method).
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware patch for the Saturn PHY fixes a bug, but is not absolutely
essential. And its licence is unclear, so it is not included in all
distributions. Just log an error message and continue if it is missing
or invalid.
References: http://bugs.debian.org/712674
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Jose Andres Arias Velichko <Andres.Arias@PaisLinux.net> (against 3.2)
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed that enh_desc value is always zero.
Due to calling order of stmmac_selec_desc_mode(), enh_desc value is always zero.
Even though mac is set to use enhanced dma descriptor, if enh_desc is zero,
functions related dma descriptor are not working correctly.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed operator typo from & to ==.
Due to incorrect operator, the result is incorrect.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setup the multicast list of the net_device instead of
clearing it blindly. This restores the multicast groups
in case of a link down/up event or when resuming from
suspend.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of places treated features wrongly, listing not-supported
features instead of supported ones. Also, the get_drvinfo ethtool
callback isn't needed, and alx_get_pauseparam can be simplified.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In two places, parts of MAC addresses are used as u32/u16
values. This can cause alignment problems, use put_unaligned
and get_unaligned to fix this.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by Ben Hutchings, use separate fields to track
current link speed and duplex setting.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ring sizes should be unsigned, pointed out by Ben Hutchings.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
That select doesn't make any sense, remove it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
100mbit half duplex is ADVERTISED_100baseT_Half, not
ADVERTISED_10baseT_Half.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even when alx_setup_speed_duplex() is called, we still
need to call alx_cfg_mac_flowcontrol() and set hw->flowctrl
if flow control changed.
This was a bug I accidentally introduced while simplifying
the original driver.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware supports the UPDATE_QP command, if the VF link is disabled,
block all QPs opened by the VF, by programming the UPDATE_QP command to drop
all RX & TX traffic to/from these QPs. Operates only in VST mode.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Within VST mode, enable modifying the vlan and/or qos
for a VF without requiring unbind/rebind.
This requires firmware which supports the UPDATE_QP command.
(If the command is not available, we fall back to requiring
unbind/bind to activate these changes).
To avoid race conditions with modify-qp on QPs that are affected
by update-qp, this operation is performed on the comm_wq.
If the update operation succeeds for all the necessary QPs, a
vlan_unregister is performed for the abandoned vlan id.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to add a newline after logging the device's MACID.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
