The patch adds driver support for reading the config id attributes from NVM
flash partition.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver interface for reading the config attributes from user
provided buffer, and updates these values on nvm config flash partition.
This is basically an expansion of our existing ethtool -f implementation.
The management FW has exposed an additional method of configuring some of
the nvram options, and this makes use of that. This implementation will
come into use when newer FW files which contain configuration directives
employing this API will be provided to ethtool -f.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supported ports in ethtool <eth1> are displayed based on media type.
For media type fibre and twinaxial, port type is "FIBRE". Media type
Base-T is "TP" and media KR is "Backplane".
V1->V2:
Corrected the subject.
Signed-off-by: Rahul Verma <rahulv@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several casts were required around dpi_addr parameter in qed_rdma_if.h
This is an address on the doorbell bar and should therefore be marked with
__iomem.
Link: https://lore.kernel.org/r/20190709141735.19193-5-michal.kalderon@marvell.com
Reported-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Based on 1 normalized pattern(s):
this software is available under the terms of the gnu general public
license gpl version 2 available from the file copying in the main
directory of this source tree
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 35 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190115.411886531@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add iWARP engine affinity setting for supporting iWARP over 100g.
iWARP cannot be distinguished by the LLH from L2, hence the
engine division will affect L2 as well. For this reason we add
a parameter to devlink to determine the engine division.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing status blocks use the affined hwfn
instead of the leading one for RDMA / Storage
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The patch adds driver interface to read the SmartAN capability from
management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Michal Kalderon <mkalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PBL chains with non power of 2 page count, the producer is not at the
beginning of the chain when index is 0 after a wrap. Therefore, after the
producer index wrap around, page index should be calculated more carefully.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the doorbelling entities are outside of the core module.
L2 queues, Roce queues, iscsi and fcoe all need to register.
Make the APIs available for these drivers.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the database used to register doorbelling entities, and APIs for adding
and deleting entries, and logic for traversing the database and doorbelling
once on behalf of all entities.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been a smaller cycle with many of the commits being smallish code
fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full packet
mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user API, and
provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute groups
and cdev properly for uverbs, and clean up some of the core code's device list
management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and rework
how RDMA holds poitners to mm_struct for get_user_pages cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices
-----BEGIN PGP SIGNATURE-----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=pacJ
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a smaller cycle with many of the commits being smallish
code fixes and improvements across the drivers.
- Driver updates for bnxt_re, cxgb4, hfi1, hns, mlx5, nes, qedr, and
rxe
- Memory window support in hns
- mlx5 user API 'flow mutate/steering' allows accessing the full
packet mangling and matching machinery from user space
- Support inter-working with verbs API calls in the 'devx' mlx5 user
API, and provide options to use devx with less privilege
- Modernize the use of syfs and the device interface to use attribute
groups and cdev properly for uverbs, and clean up some of the core
code's device list management
- More progress on net namespaces for RDMA devices
- Consolidate driver BAR mmapping support into core code helpers and
rework how RDMA holds poitners to mm_struct for get_user_pages
cases
- First pass to use 'dev_name' instead of ib_device->name
- Device renaming for RDMA devices"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (242 commits)
IB/mlx5: Add support for extended atomic operations
RDMA/core: Fix comment for hw stats init for port == 0
RDMA/core: Refactor ib_register_device() function
RDMA/core: Fix unwinding flow in case of error to register device
ib_srp: Remove WARN_ON in srp_terminate_io()
IB/mlx5: Allow scatter to CQE without global signaled WRs
IB/mlx5: Verify that driver supports user flags
IB/mlx5: Support scatter to CQE for DC transport type
RDMA/drivers: Use core provided API for registering device attributes
RDMA/core: Allow existing drivers to set one sysfs group per device
IB/rxe: Remove unnecessary enum values
RDMA/umad: Use kernel API to allocate umad indexes
RDMA/uverbs: Use kernel API to allocate uverbs indexes
RDMA/core: Increase total number of RDMA ports across all devices
IB/mlx4: Add port and TID to MAD debug print
IB/mlx4: Enable debug print of SMPs
RDMA/core: Rename ports_parent to ports_kobj
RDMA/core: Do not expose unsupported counters
IB/mlx4: Refer to the device kobject instead of ports_parent
RDMA/nldev: Allow IB device rename through RDMA netlink
...
Added transceiver type, speed capability and board types
in HSI, are utilizing to display the accurate link
information in ethtool.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver support for configuring/reading the 20G link speed.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clang warns when one enumerated type is explicitly converted to another.
drivers/infiniband/hw/qedr/qedr_roce_cm.c:198:28: warning: implicit
conversion from enumeration type 'enum qed_roce_ll2_tx_dest' to
different enumeration type 'enum qed_ll2_tx_dest' [-Wenum-conversion]
ll2_tx_pkt.tx_dest = pkt->tx_dest;
~ ~~~~~^~~~~~~
1 warning generated.
Turns out that QED_ROCE_LL2_TX_DEST_NW and QED_ROCE_LL2_TX_DEST_LB are
only used once in the whole tree and QED_ROCE_LL2_TX_DEST_MAX is used
nowhere. Remove them and use the equivalent values from qed_ll2_tx_dest
in their place.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Acked-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for tc mqprio offload,
using this different traffic classes on the adapter
can be utilized based on configured priority to tc map.
For example -
tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3
This will cause SKBs with priority 0,1,2,3 to transmit
over tc 0,1,2,3 hardware queues respectively.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds qed APIs for reading the PHY module.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features.
RDMA
- Several modifications and fixes for Memory Windows
- drop vlan and tcp timestamp from mss calculation in driver for
this FW
- Fix SQ completion flow when local ack timeout is infinite
- Modifications in t10dif support
ETH
- Fix aRFS for tunneled traffic without inner IP.
- Fix chip configuration which may fail under heavy traffic conditions.
- Support receiving any-VNI in VXLAN and GENEVE RX classification.
iSCSI / FcoE
- Fix iSCSI recovery flow
- Drop vlan and tcp timestamp from mss calc for fw 8.37.2.0
Misc
- Several registers (split registers) won't read correctly with
ethtool -d
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring SRQ and provides the necessary
APIs for rdma upper layer driver (qedr) to enable the SRQ feature.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Yuval Bason <yuval.bason@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for capturing the link change count in
ethtool statistics display.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.
For example -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver supports flow classification to PF
receive queues based on TCP/UDP 4 tuples [src_ip, dst_ip,
src_port, dst_port] only.
This patch enables to configure different flow profiles
[For example - only UDP dest port or src_ip based] on the
adapter so that classification can be done according to
just those fields as well. Although, at a time just one
type of flow configuration is supported due to limited
number of flow profiles available on the device.
For example -
ethtool -N enp7s0f0 flow-type udp4 dst-port 45762 action 2
ethtool -N enp7s0f0 flow-type tcp4 src-ip 192.16.4.10 action 1
ethtool -N enp7s0f0 flow-type udp6 dst-port 45762 action 3
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data member 'is_mf_default' is not used by the qed/qede drivers,
removing the same.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration information is added to the debug data collection, in
addition to register dump.
Added qed_dbg_nvm_image() that receives an image type, allocates a
buffer and reads the image. The images are saved in the buffers and the
dump size is updated.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the required driver support for updating the flash or
non volatile memory of the adapter. At highlevel, flash upgrade comprises
of reading the flash images from the input file, validating the images and
writing them to the respective paritions.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features
RDMA Features
- SRQ support
- XRC support
- Memory window support
- RDMA low latency queue support
- RDMA bonding support
RDMA bug fixes
- RDMA remote invalidate during retransmit fix
- iWARP MPA connect interop issue with RTR fix
- iWARP Legacy DPM support
- Fix MPA reject flow
- iWARP error handling
- RQ WQE validation checks
MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
for LB packets
ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering
iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration
DEBUG
- Update debug utilities
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Acked-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Advance the qed* drivers to use firmware 8.33.1.0:
Modify core driver (qed) to utilize the new FW and initialize the device
with it. This is the lion's share of the patch, and includes changes to FW
interface files, device initialization flows, FW interaction flows, and
debug collection flows.
Modify Ethernet driver (qede) to make use of new FW in fastpath.
Modify RoCE/iWARP driver (qedr) to make use of new FW in fastpath.
Modify FCoE driver (qedf) to make use of new FW in fastpath.
Modify iSCSI driver (qedi) to make use of new FW in fastpath.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Bason <Yuval.Bason@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Chopra <Manish.Chopra@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames defines and structures in the FW HSI files to allow a
distinction between different types of HW.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors and reorders the FW API files in preparation of
upgrading the code to support new FW.
- Make use of the BIT macro in appropriate places.
- Whitespace changes to align values and code blocks.
- Comments are updated (spelling mistakes, removed if not clear).
- Group together code blocks which are related or deal with similar
matters.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For iWARP unaligned MPA flow, a slowpath event of flushing an
MPA connection that entered an unaligned state is required.
The flush ramrod is received on the ll2 queue, and a pre-registered
callback function is called to handle the flush event.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The option of sending a packet on the ll2 and dropping it exists in
hardware and was not used until now, thus not exposed.
The iWARP unaligned MPA flow requires this functionality for
flushing the tx queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When more than one ll2 queue is opened ( that is not an OOO queue )
ll2 code does not have enough information to determine whether
the queue is the main one or not, so a new field is added to the
acquire input data to expose the control of determining whether
the queue is the main queue or a secondary queue.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A SYN packet which arrives with errors from FW should be dropped.
This required adding an additional field to the ll2
rx completion data.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maximum coalesce per Rx/Tx queue is extended from
255 to 511.
Signed-off-by: Rahul Verma <rahul.verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retrieve the actual coalesce value from hardware for every Rx/Tx
queue, instead of Rx/Tx coalesce value cached during set coalesce.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the ethtool support to set RX/Tx coalesce
value to the VF associated Rx/Tx queues.
Signed-off-by: Rahul Verma <Rahul.Verma@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required driver support for reading/configuring the
Energy Efficient Ethernet (EEE) parameters.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces error handling for errors that occurred during
connection establishment.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.
Error handling is not part of this patch.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new connection type for iWARP ll2 connections for setting
correct ll2 filters and connection type to FW.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make some names more generic as they will be used by iWARP too.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds iWARP support for flows that have common code
between RoCE and iWARP, such as initialization, teardown and
qp setup verbs: create, destroy, modify, query.
It introduces the iWARP specific files qed_iwarp.[ch] and
iwarp_common.h
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP personality introduced the need for differentiating in several
places in the code whether we are RoCE, iWARP or either. This
leads to introducing new macros for querying the personality.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the qed_roce_if file to qed_rdma_if as it
represents a common interface for RoCE and iWARP.
this commit affects RDMA/qedr as well.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_QED_RDMA isn't defined, we'd hit the following:
/include/linux/qed/qede_rdma.h:84:19:
warning: ‘qede_rdma_dev_add’ used but never defined [enabled by default]
static inline int qede_rdma_dev_add(struct qede_dev *dev);
Fixes: bbfcd1e8e1 ("qed*: Set rdma generic functions prefix")
Signed-off-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the functions common to both iWARP and RoCE to have a prefix of
_rdma_ instead of _roce_.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we have iWARP support, the qede portion of the qedr<->qede would
serve all the RDMA protocols - so rename the file to be appropriate
to its function.
While we're at it, we're also moving a couple of inclusions to it into
.h files and adding includes to make sure it contains all type
definitions it requires.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iWARP would require the chains to allocate/free their PBL memory
independently, so add the infrastructure to provide it externally.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LL2 today is interrupt driven - when tx/rx completion arrives [or any
other indication], qed needs to operate on the connection and pass
the information to the protocol-driver [or internal qed consumer].
Since we have several flavors of ll2 employeed by the driver,
each handler needs to do an if-else to determine the right functionality
to use based on the connection type.
In order to make things more scalable [given that we're going to add
additional types of ll2 flavors] move the infrastrucutre into using
a callback-based approach - the callbacks would be provided as part
of the connection's initialization parameters.
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A LL2 connection [qed_ll2_info] has a sub-structure of type qed_ll2_conn
that contain various inputs for ll2 acquisition, but the connection also
utilizes a couple of other inputs.
Restructure the input structure to include all the inputs and refactor
the code necessary to populate those.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces qed_ll2_comp_rx_data as a public struct
and moves handling of Rx packets in LL2 into using it.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step in revising the LL2 interface, this declares
qed_ll2_tx_pkt_info as part of the ll2 interface, and uses it for
transmission instead of receiving lots of parameters.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The final addition on the qed front -
- VFs would now require their PFs to provide multiple CIDs
- Based on the availability of connections from PF, determine whether
XDP is feasible and share it with qede via dev_info.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the infrastructure for supporting VFs that want to open
multiple transmission queues on the same queue-zone.
At this point, there are no VFs that actually request this functionality,
but later patches would remedy that.
a. VF and PF would communicate the capability during ACQUIRE;
Legacy VFs would continue on behaving as they do today
b. PF would communicate number of supported CIDs to the VF
and would enforce said limitation
c. Whenever VF passes a request for a given queue configuration
it would also pass an associated index within said queue-zone
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of an effort of a cleaner seperation between qed and the protocol
drivers, the L2 interface is to use the SB structure for initialization
purposes opaquely.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhance API between qedi and qed, allowing qedi to inform device's
firmware when the iSCSI mac is to be changed.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storage drivers require images from the nvram in boot-from-SAN
scenarios. This provides the necessary API between qed and the
protocol drivers to perform such reads.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Share several new tidbits with qedf:
- wwpn & wwnn
- Absolute pf-id [this one is actually meant for qedi as well]
- Number of available CQs
While we're at it, now that qedf will be aware of the available CQs
we can add some validation on the inputs it provides.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already have an API struct that contains interrupt-related
numbers. Use it to encapsulate all information relating to the
status of SBs as (used|free).
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current API between qed and protocol modules allows passing an
additional private string - but it doesn't get utilized by qed
anywhere.
Clarify the API by removing it and renaming it 'set_name'.
CC: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass additional information about package installed on persistent memory
so that protocol drivers would be able to log it.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pushes qed [and as result, all qed* drivers] into using 8.20.0.0
firmware. The changes are mostly contained in qed with minor changes
to qedi due to some HSI changes.
Content-wise, the firmware contains fixes to various issues exposed
since the release of the previous firmware, including:
- Corrects iSCSI fast retransmit when data digest is enabled.
- Stop draining packets when receiving several consecutive PFCs.
- Prevent possible assertion when consecutively opening/closing
many connections.
- Prevent possible assertion due to too long BDQ fetch time.
In addition, the new firmware would allow us to later add iWARP support
in qed and qedr.
Changes from previous version
-----------------------------
- V2: Fix warning in qed_debug.c
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value for status block id could be more than 256 in 100G mode, need to
update its data type from u8 to u16.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP hardware filter configuration performed by the driver for a given
user requested config is not correct for some of the PTP modes.
Following changes are needed for PTP config-filter implementation.
1. NIG_REG_TX_PTP_EN register - Bits 0/1/2 respectively enables
TimeSync/"V1 frame format support"/"V2 frame format support" on
the TX side. Set the associated bits based on the user request.
2. ptp4l application fails to operate in Peer Delay mode. Following
changes are needed to fix this,
a. Driver should enable (set to 0) DA #1-related bits for IPv4,
IPv6 and MAC destination addresses in these registers:
NIG_REG_TX_LLH_PTP_RULE_MASK
NIG_REG_LLH_PTP_RULE_MASK
b. NIG_REG_LLH_PTP_PARAM_MASK/NIG_REG_TX_LLH_PTP_PARAM_MASK should
be set to 0x0 in all modes.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output to the RDMA driver whether DPM mode is enabled or disabled in
the HW and if so what is the number of WIDs it supports
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for UDP ports in bulletin board
to notify UDP ports change to the VFs
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables tunnel feature offloads based on hw configuration
at initialization time instead of enabling them always.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for static/local dcbx mode. In this mode
adapter brings up the dcbx link with locally configured parameters
instead of performing the dcbx negotiation with the peer. The feature
is useful when peer device/switch doesn't support dcbx.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds necessary APIs to interface with
qede aRFS support in successive patch.
It also reserves separate PTT entry for aRFS,
[as being in fastpath flow] for hardware access instead of
trying to acquire it at run time from the ptt pool.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that management firmware is capable of telling us the number of CQs
available for a given PF, qed needs to communicate the number to qedi
so it would know have many to use.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's possible some configurations would prevent driver from utilizing
all the Memory Regions due to a lack of ILT lines.
In such a case, calculate how many memory regions would have to be
dropped due to limit, and manage without those.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the necessary infrastructure changes for initializing
and working with the new series of QL41xxx adapaters.
It also adds 2 new PCI device-IDs to qede:
- 0x8070 for QL41xxx PFs
- 0x8090 for VFs spawning from QL41xxx PFs
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch advances the qed* drivers into using the newer firmware -
This solves several firmware bugs, mostly related [but not limited to]
various init/deinit issues in various offloaded protocols.
It also introduces a major 4-Cached SGE change in firmware, which can be
seen in the storage drivers' changes.
In addition, this firmware is required for supporting the new QL41xxx
series of adapters; While this patch doesn't add the actual support,
the firmware contains the necessary initialization & firmware logic to
operate such adapters [actual support would be added later on].
Changes from Previous versions:
-------------------------------
- V2 - fix kbuild-test robot warnings
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Signed-off-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Chad Dupuis <Chad.Dupuis@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the FCoE driver (qedf) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds the required qed interfaces for configuring/reading
the PTP clock on the adapter.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trusted VFs would be allowed to receive promiscuous and
multicast promiscuous data.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A step toward having qede agnostic to the queue configurations
in firmware/hardware - let the RSS indirections use queue handles
instead of actual queue indices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the submission of the qedr driver, there's inconsistency
in the licensing of the various qed/qede files - some are GPLv2
and some are dual-license.
Since qedr requires dual-license and it's dependent on both,
we're updating the licensing of all qed/qede source files.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the backbone required for the various HW initalizations
which are necessary for the iSCSI driver (qedi) for QLogic FastLinQ
4xxxx line of adapters - FW notification, resource initializations, etc.
Signed-off-by: Arun Easi <arun.easi@cavium.com>
Signed-off-by: Yuval Mintz <yuval.mintz@cavium.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to maintain several FW/HW-indices for each one of
its queues. Currently, that mapping is done by the QED where it uses
an rx/tx array of so-called hw-cids, populating them whenever a new
queue is opened and clearing them upon destruction of said queues.
This maintenance is far from ideal - there's no real reason why
QED needs to maintain such a data-structure. It becomes even worse
when considering the fact that the PF's queues and its child VFs' queues
are all mapped into the same data-structure.
As a by-product, the set of parameters an interface needs to supply for
queue APIs is non-trivial, and some of the variables in the API
structures have different meaning depending on their exact place
in the configuration flow.
This patch re-organizes the way L2 queues are configured and maintained.
In short:
- Required parameters for queue init are now well-defined.
- Qed would allocate a queue-cid based on parameters.
Upon initialization success, it would return a handle to caller.
- Queue-handle would be maintained by entity requesting queue-init,
not necessarily qed.
- All further queue-APIs [update, destroy] would use the opaque
handle as reference for the queue instead of various indices.
The possible owners of such handles:
- PF queues [qede] - complete handles based on provided configuration.
- VF queues [qede] - fw-context-less handles, containing only relative
information; Only the PF-side would need the absolute indices
for configuration, so they're omitted here.
- VF queues [qed, PF-side] - complete handles based on VF initialization.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chain structure and functions are widely used by the qed* modules,
both for configuration and datapath.
E.g., qede's Tx has one such chain and its Rx has two.
Currently, the strucutre's fields which are required for datapath
related functions [produce/consume] are intertwined with fields which
are required only for configuration purposes [init/destroy/etc.].
This patch re-arranges the chain structure so that all the fields which
are required for datapath usage could reside in a single cacheline instead
of the two which are required today.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
