The tps65982 feeds the bq25895 charge controller on the Librem 5.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With the pmic driver fixed we can now shut off the regulator in the gpc.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is consistent with other IRQs and makes keeps currents low.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
"make dtbs_check" fails with:
arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dt.yaml: eeprom@50: compatible: 'oneOf' conditional failed, one must be fixed:
'microchip,at24c64' does not match '^(atmel|catalyst|microchip|nxp|ramtron|renesas|rohm|st),(24(c|cs|lc|mac)[0-9]+|spd)$'
Fix this by dropping the bogus "at" prefix.
Fixes: a1d8a344f1 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210128110136.2293490-1-geert+renesas@glider.be
Increase the SmartEEE Tw parameter for Atheros PHYs to stop gigabit
links from sporadically dropping. Testing on this platform shows that
a value of 24 results in a stable link, whereas 23 or below has the
occasional drop.
Tested with a Netgear GS116 unmanaged switch link partner with Cat 5e
cabling.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We are using Jailhouse Hypervsior which has virtual pci node that
use dt domains. so also use dt domains for pci node, this will avoid
conflict with Jailhouse Hypervisor to trigger the following error:
pr_err("Inconsistent \"linux,pci-domain\" property in DT\n");
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MT8183 display PWM device will not work until the associated
power-domain is enabled. Add the power-domain reference to the node
allows the display PWM driver to operate and the backlight turn on.
Fixes: f15722c0fe ("arm64: dts: mt8183: Add pwm and backlight node")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20210113215723.71966-1-enric.balletbo@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add support for the variant of the Jetson Xavier NX Developer Kit that
has a system-on-module which includes an eMMC.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
There are two versions of the Jetson Xavier NX system-on-module; one
with a micro SD-card slot and one with an eMMC. Currently, only the
system-on-module with the micro SD-card slot is supported. Before adding
support for the eMMC variant, move the common device-tree parts of the
existing Jetson Xavier NX system-on-module board (p3668-0000) and
reference carrier board (p3509-0000) into include files that can be used
by both Jetson Xavier NX variants.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
property name must include only lowercase and '-'
Fixes: 91f9c963ce ("arm64: dts: mt8183: Add display nodes for MT8183")
Signed-off-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/20210128112314.1304160-2-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
We can use CPU specific pmu configuration to expose the appropriate
CPU specific events rather than just the basic generic pmuv3 perf
events.
Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Tero Kristo <kristo@kernel.org>
Link: https://lore.kernel.org/r/20210120195145.32259-1-nm@ti.com
wrongly used dt properties and parts that shouldn't be enabled.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAmAQV9MQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgRTWCACsJ1R9z6KJRKiFayLykyw4a3/wTGUQyBHV
7jyF9FmkDo1wzNFpR3uQw124NwdXWUzUZGwyL1qgxk5RCBiN0E9I1xQZ819rMx/a
Q9rZj9b0r39fh4giON7yc7U8UQroToChIfr1NieQZL6QuolCULibMQBg4LGAx8NB
FM+ThGmw55yRphiUwjPJoi/PUWhrt69E2bf8u44CFi6x6YLz0QnTN0yJ4A8R6ps5
bfxaHGEX1wYlYYiWbNNsPIZVT/1gfjsAJydsDwwLwuO24Rdx8IjYTr9gRE86k1t5
H+nCd92p7WVTkCyEVGoq5hlYvbb0IzPTaqi2XLxNw9Qn/KgEaXBc
=95NW
-----END PGP SIGNATURE-----
Merge tag 'v5.11-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/fixes
Wrong irq number on px30 and cleanups of stuff on rk3399 regarding
wrongly used dt properties and parts that shouldn't be enabled.
* tag 'v5.11-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Disable display for NanoPi R2S
arm64: dts: rockchip: remove interrupt-names property from rk3399 vdec node
arm64: dts: rockchip: Fix PCIe DT properties on rk3399
arm64: dts: rockchip: Use only supported PCIe link speed on Pinebook Pro
arm64: dts: rockchip: fix vopl iommu irq on px30
Link: https://lore.kernel.org/r/5429065.DvuYhMxLoT@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For the proper reboot Odroid-C4 board requires to switch TFLASH_VDD_EN
pin to the high impedance mode, otherwise the board is stuck in the
middle of loading early stages of the bootloader from SD card.
This can be achieved by using the OPEN_DRAIN flag instead of the
ACTIVE_HIGH, what will leave the pin in input mode to achieve high state
(pin has the pull-up) and solve the issue.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: 326e57518b ("arm64: dts: meson-sm1: add support for Hardkernel ODROID-C4")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20210122055218.27241-1-m.szyprowski@samsung.com
Remove SATA from Stingray as it is unsupported.
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4908 has internal switch with 5 GPHYs. Ports 0 - 3 are always
connected to the internal PHYs. Remaining ports depend on device setup.
Asus GT-AC5300 has an extra switch with its PHYs accessible using the
internal MDIO.
CPU port and Ethernet interface remain to be documented.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable support for audio-graph based sound card on Jetson-Nano and
Jetson-TX1. Depending on the platform, required I/O interfaces are
enabled.
* Jetson-Nano: Enable I2S3, I2S4, DMIC1 and DMIC2.
* Jetson-TX1: Enable all I2S and DMIC interfaces.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Expose a header which describes DT bindings required to use audio-graph
based sound card. All Tegra210 based platforms can include this header
and add platform specific information. Currently, from SoC point of view,
all links are exposed for ADMAIF, AHUB, I2S and DMIC components.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Device tree nodes are ordered by unit-address and alphabetically by name
if a node doesn't have a unit-address. The thermal sensor and timer
nodes were not sorted in the correct order, so do that now.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit enables USB host mode at J512 type-C port of Jetson-Xavier.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PMC driver provides USB sleepwalk registers access to XUSB PADCTL
driver. This commit adds a "nvidia,pmc" property which points to
PMC node to XUSB PADCTL device node.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
HDA initialization is failing occasionally on Tegra210 and following
print is observed in the boot log. Because of this probe() fails and
no sound card is registered.
[16.800802] tegra-hda 70030000.hda: no codecs found!
Codecs request a state change and enumeration by the controller. In
failure cases this does not seem to happen as STATETS register reads 0.
The problem seems to be related to the HDA codec dependency on SOR
power domain. If it is gated during HDA probe then the failure is
observed. Building Tegra HDA driver into kernel image avoids this
failure but does not completely address the dependency part. Fix this
problem by adding 'power-domains' DT property for Tegra210 HDA. Note
that Tegra186 and Tegra194 HDA do this already.
Fixes: 742af7e7a0 ("arm64: tegra: Add Tegra210 support")
Depends-on: 96d1f078ff ("arm64: tegra: Add SOR power-domain for Tegra210")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This fixes a regression in Lenovo Yoga C630, where the touchpad in some
units stopped working, by re-enabling the "tsc2" device.
It also marks the LPASS related clocks as protected to allow DB845c and
the Lenovo Yoga C630 to boot even if CONFIG_SDM_LPASSCC_845 is enabled.
-----BEGIN PGP SIGNATURE-----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=E0WN
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/fixes
Qualcomm ARM64 fixes for 5.11
This fixes a regression in Lenovo Yoga C630, where the touchpad in some
units stopped working, by re-enabling the "tsc2" device.
It also marks the LPASS related clocks as protected to allow DB845c and
the Lenovo Yoga C630 to boot even if CONFIG_SDM_LPASSCC_845 is enabled.
* tag 'qcom-arm64-fixes-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: dts: qcom: sdm845: Reserve LPASS clocks in gcc
arm64: dts: qcom: c630: keep both touchpad devices enabled
Link: https://lore.kernel.org/r/20210125232039.642565-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It has been reported on IRC and in KernelCI boot tests, this change breaks
internal PHY support on the Amlogic G12A/SM1 Based boards.
We suspect the added signal to reset more than the Ethernet MAC but also
the MDIO/(RG)MII mux used to redirect the MAC signals to the internal PHY.
This reverts commit f3362f0c18 while we find
and acceptable solution to cleanly reset the Ethernet MAC.
Reported-by: Corentin Labbe <clabbe@baylibre.com>
Acked-by: Jérôme Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20210126080951.2383740-1-narmstrong@baylibre.com
NanoPi R2S is headless, so rightly does not enable any of the display
interface hardware, which currently provokes an obnoxious error in the
boot log from the fake DRM device failing to find anything to bind to.
It probably isn't *too* hard to obviate the fake device shenanigans
entirely with a bit of driver reshuffling, but for now let's just
disable it here to shut up the spurious error.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/c4553dfad1ad6792c4f22454c135ff55de77e2d6.1611186099.git.robin.murphy@arm.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The NanoPi M4B is a minor revision of the original M4.
The differences against the original Nanopi M4 that are common with the
other M4V2 revision include:
- microphone header removed
- power button added
- recovery button added
Additional changes specific to the M4B:
- USB 3.0 hub removed; board now has 2x USB 3.0 type-A ports and 2x
USB 2.0 ports
- ADB toggle switch added; this changes the top USB 3.0 host port to
a peripheral port
- Type-C port no longer supports data or PD
- WiFi/Bluetooth combo chip switched to AP6256, which supports BT 5.0
but only 1T1R (down from 2T2R) for WiFi
Add a new dts file for the new board revision that shows the difference
against the original.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210121162321.4538-5-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Only the NanoPC T4 hs the PCIe reset pin routed to the SoC. For the
NanoPi M4 family, no such signal is routed to the expansion header on
the base board.
As the schematics for the expansion board were not released, it is
unclear how this is handled, but the likely answer is that the signal
is always pulled high.
Move the ep-gpios property from the common nanopi4.dtsi file to the
board level nanopc-t4.dts file. This makes the nanopi-m4 lack ep-gpios,
matching the board design.
A companion patch "PCI: rockchip: make ep_gpio optional" for the Linux
driver is required, as the driver currently requires the property to be
present.
Fixes: e7a0959082 ("arm64: dts: rockchip: Add devicetree for NanoPC-T4")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210121162321.4538-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds support for the following Xperias:
* Z3+ [aka Z4 in some regions] (Ivy)
* Z4 Tablet (Karin)
* Z4 Tablet Wi-Fi (Karin_windy) [APQ8094]
* Z5 Compact (Suzuran)
* Z5 Premium (Satsuki)
These devices are very similar in terms of hardware, with main
differences being display panels.
While at it, update comments describing hardware used:
SMB charger seems to not be used after all, PMI8994 charger
is in use instead.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Link: https://lore.kernel.org/r/20210118162432.107275-1-konrad.dybcio@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
SCIF0 has been enabled by the firmware, so it worked already. Still, add
the proper nodes to make it work in any case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121110008.15894-3-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This is the result of multiple patches taken from the BSP, combined,
rebased, and properly sorted. SCIF0 gets DMA properties, other SCIFs are
entirely new.
Signed-off-by: Linh Phung <linh.phung.jy@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121110008.15894-2-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Define the generic parts of Ethernet-AVB device nodes. Only AVB0 was
tested because it was the only port with a PHY on current hardware.
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
[wsa: double checked, rebased, added "internal-delay" properties]
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210121100619.5653-4-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some SDHI instances are solely used for eMMC. Disable SD and SDIO
for faster initialization.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Adam Ford <aford173@gmail.com> (beacon)
Link: https://lore.kernel.org/r/20210119133322.87289-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The thermal devicetree binding requires the "-thermal" suffix for all
thermal zones. Hence, add the missing suffix for PMIC based thermal
zones.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210118051005.55958-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now the dtbs_check produces below warnings
sdhci@4f80000: clock-names:0: 'clk_ahb' was expected
sdhci@4f80000: clock-names:1: 'clk_xin' was expected
$nodename:0: 'sdhci@4f80000' does not match '^mmc(@.*)?$'
Fix above warnings by updating mmc DT definitions to follow
sdhci-am654.yaml bindings:
- rename sdhci dt nodes to 'mmc@'
- swap clk_xin/clk_ahb clocks, the clk_ahb clock expected to be defined
first
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210115193016.5581-1-grygorii.strashko@ti.com
The "modem-remoteproc" property is no longer required for the IPA
driver, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "modem-remoteproc" property is no longer required for the IPA
driver, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the registers and clock for the Inline Crypto Engine (ICE) to the
device tree node for the sdhci-msm host controller on sdm630. This
allows sdhci-msm to support inline encryption on sdm630.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Link: https://lore.kernel.org/r/20210121090140.326380-9-ebiggers@kernel.org
[bjorn: Changed indentation]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Port thermal zones definitions from msm-4.19 tree. Enable and add
channel configuration to PMIC's ADC-TM definitions. Declare thermal
zones and respective trip points.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210119054848.592329-5-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The commit 3eb619b2f7 ("scripts/dtc: Update to upstream version
v1.6.0-11-g9d7888cbf19c") updated dtc version which also contained DTC
commit
"81e0919a3e21 checks: Add interrupt provider test"
where reasons for this checking are mentioned as
"A missing #address-cells property is less critical, but creates
ambiguities when used in interrupt-map properties, so warn about this as
well now."
That's why add address-cells property to gic and gpio nodes to get rid of
this warning.
CC: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/e4f54ddce33b79a783aa7c76e0dc6e9787933610.1606918493.git.michal.simek@xilinx.com
In commit 208921bae6 ("arm64: dts: qcom: pmi8998: Add nodes for
LAB and IBB regulators") bindings for the lab/ibb regulators were
added to the pmi8998 dt, but the original committer has never
specified what the interrupts were for.
LAB and IBB regulators provide two interrupts, SC-ERR (short
circuit error) and VREG-OK but, in that commit, the regulators
were provided with two different types of interrupts;
specifically, IBB had the SC-ERR interrupt, while LAB had the
VREG-OK one, none of which were (luckily) used, since the driver
didn't actually use these at all.
Assuming that the original intention was to have the SC IRQ in
both LAB and IBB, as per the names appearing in documentation,
fix the SCP interrupt.
While at it, also add the OCP interrupt in order to be able to
enable the Over-Current Protection feature, if requested.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210119174421.226541-8-angelogioacchino.delregno@somainline.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The ZTE ZX set-top-box SoC platform was added in 2015 by Jun Nie, with
Baoyou Xie and Shawn Guo subsequently becoming maintainers after the
addition of the 64-bit variant.
However, the only machines that were ever supported upstream are the
reference designs, not actual set-top-box devices that would benefit
from this support. All ZTE set-top-boxes from the past few years seem
to be based on third-party SoCs. While there is very little information
about zx296702 and zx296718 on the web, I found some references to other
chips from the same family, such as zx296716 and zx296719, which were
never submitted for upstream support. Finally, there is no support for
the GPU on either of them, with the lima and panfrost device drivers
having been added after work on the zx platform had stopped.
Shawn confirmed that he has not seen any interest in this platform for
the past four years, and that it can be removed.
Thanks to Jun and Shawn for maintaining this platform over the past
five years.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Switch reset pin of ov8856 node from GPIO_ACTIVE_HIGH to GPIO_ACTIVE_LOW,
this issue prevented the ov8856 from probing properly as it did not respon
to I2C messages.
Fixes: d4919a4456 ("arm64: dts: qcom: sdm845-db845c: Add ov8856 & ov7251
camera nodes")
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://lore.kernel.org/r/20201221100955.148584-1-robert.foss@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A test with the command below gives this error:
/arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: video-codec@ff660000:
'interrupt-names' does not match any of the regexes: 'pinctrl-[0-9]+'
The rkvdec driver gets it irq with help of the platform_get_irq()
function, so remove the interrupt-names property from the rk3399
vdec node.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
media/rockchip,vdec.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210117181653.24886-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC.
As the official wiki page puts it, "E for Ethernets".
It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both
directly served by Ethernet controllers in the SoC, a USB 3.0 host port,
a power-only USB type-C port, a 3.5mm headphone jack for audio output,
two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT
and PoE header.
The board comes in multiple configurations, differing in the amount of
onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac
2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants
can all share the same device tree.
The USB 2.0 OTG controller is available on the 40-pin header. This is
not enabled in the device tree, since it is possible to use it in a
host-only configuration, or in OTG mode with an extra pin from the
header as the ID pin.
The device tree is based on the one of the Rock64, with various parts
modified to match the ROCK Pi E, and some parts updated to newer styles,
such as the gmac2io node's mdio sub-node.
Add a new device tree file for the new board.
The voltages for the adc-keys were selected to have some tolerances for
resistor variances and the ADC itself also causing voltage drops. Since
the recover button is the only button on the adc line, this should not
cause any issues.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210117100710.4857-4-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The gmac2phy is integrated with the PHY within the SoC. Any properties
related to this integration can be included in the .dtsi file, instead
of having board dts files specify them separately.
Add the clock_in_out property to specify the direction of the PHY clock.
This is the minimum required to have gmac2phy working on Linux. Other
examples include assigned-clocks, assigned-clock-rates, and
assigned-clock-parents properties, but the hardware default plus the
implementation requesting the appropriate clock rate also works.
Fixes: 9c4cc910fe ("ARM64: dts: rockchip: Add gmac2phy node support for rk3328")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210117100710.4857-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
/arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml:
thermal-zones: 'cpu', 'gpu' do not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Rename Rockchip rk3399 thermal subnodes so that it ends
with "-thermal"
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
thermal/thermal-zones.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210117150953.16475-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A test with the command below gives for example this error:
/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dt.yaml:
thermal-zones: 'cpu', 'gpu' do not match any of the regexes:
'^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+'
Make the rk3368 thermal subnode names in line with the rest of
the Rockchip dts files. Add a label and rename them so that it ends
with "-thermal"
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
thermal/thermal-zones.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210117150953.16475-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add mac address in efuse, so that FEC driver can parse it from nvmem
cell.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
CLK_ENET_TIMER assigned clocks twice, should be a typo, correct to
CLK_ENET_PHY_REF clock.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pwm-backlight binding requires a power supply. Make sure we provide
one.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210114113538.1233933-7-maxime@cerno.tech
According to the LED bindings, the LED node names are supposed to be led
plus an optional suffix. Let's fix our users to use that new scheme.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20210114113538.1233933-6-maxime@cerno.tech
Add device nodes for the Clock-Synchronized Serial Interface with
FIFO (MSIOF) instances on the Renesas R-Car V3U (r8a779a0) SoC.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210108104345.2026857-1-geert+renesas@glider.be
On i.MX8MP, The GPIO3's secondary gpio-ranges's 'gpio controller offset'
cell value should be 26, so correct it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Fixes: 6d9b8d2043 ("arm64: dts: freescale: Add i.MX8MP dtsi support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have a proper driver for the FlexSPI interface use it. This
will fix SCK frequency switching on Layerscape SoCs.
This was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The H6 SoC contains an undocumented but fully functional RSB controller.
Add support for it. The MMIO register address matches other SoCs of the
same generation, and the IRQ matches a hole in the documented IRQ list.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
[wens@csie.org: Use raw numbers instead of macros for clock/reset index]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
With a newer bootloader SATA might be used in a mPCI slot using a mSATA
card. Enable the SATA controller on the Kontron K-Box LS-230-A which
comes with such a slot.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RTC interrupt is incorrect and prevents the RTC driver
initialising. In any case, the PCF2127 driver wants an active low
interrupt, which neither the GIC nor the GPIO blocks support.
There is an ISPPT block in the LX2160A, but this is not supported
in mainline kernels. So, just delete the interrupt.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the i.MX8MN Beacon SOM, there is an RTC chip which is fed power
from the baseboard during power off. The SNVS RTC integrated into
the SoC is not fed power. Depending on the order the modules are
loaded, this can be a problem if the external RTC isn't rtc0.
Make the alias for rtc0 point to the external RTC all the time and
rtc1 point to the SVNS in order to correctly hold date/time over
a power-cycle.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The WiFi chip is capable of communication at SDR104 speeds.
Enable 100Mhz and 200MHz pinmux to support this.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl/9n4AUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5pmQf+O0hRAVWaMXk4SCs/CsQ4Z6XNPSfz
7DSnkz0Rg53uykv+oe57sryBHGI46vy/hJeD6/OX4XgnlxaKXwmdaE+sek85D01h
C/Gzg7lKDvr8vWKZcOzhTQhs9F+EuHSsS2zW9StUBBSlXx3r2h9f+kJOLihFwvQp
CCWU+eGXgRIqZme5tIX9tFqPP1PmNRfIbZWgLwx9e/foCMl64fJSIe45ik4WePeV
+WCB3xMP38q2bfhZQv164uIw8m5/nEb8dp9O+zNamy/RN1hQqRaq1sPAwrjcqs2z
whaVS3iaGRM/RyAdbxy1JCxM+yDNM0Vnby/txVgsEOE+a9mfl2D2upQ1NA==
=+e1G
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.11:
- Fix backlight pwm on imx6qdl-kontron-samx6i which is lost from
#pwm-cells conversion.
- Fix duplicated bus node name for i.MX8MN SoC.
- Fix reset register offset on LS1028A SoC.
- Rename MMC node aliases for imx6q-tbs2910 to keep the MMC device
index consistent with previous kernel version.
- Selecting ARM_GIC_V3 on non-CP15 processors to fix one build failure
with i.MX8M SoC driver.
- Fix typos with status property on imx6qdl-kontron-samx6i board.
- Fix duplicated regulator-name on imx6qdl-gw52xx board.
* tag 'imx-fixes-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-gw52xx: fix duplicate regulator naming
ARM: dts: imx6qdl-kontron-samx6i: fix i2c_lcd/cam default status
ARM: imx: fix imx8m dependencies
ARM: dts: tbs2910: rename MMC node aliases
arm64: dts: ls1028a: fix the offset of the reset register
arm64: dts: imx8mn: Fix duplicate node name
ARM: dts: imx6qdl-kontron-samx6i: fix pwms for lcd-backlight
Link: https://lore.kernel.org/r/20210112131224.GI28365@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Lower drive strength for microSD data and CMD pins from 16 to 10. This
fixes spurious card removal issues observed on some boards. Also this
change allows us to re-enable 1.8V support, which seems to work with
lowered drive strength.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Veerabhadrarao Badiganti <vbadigan@codeaurora.org>
Fixes: 53a8ccf1c7 ("arm64: dts: qcom: rb5: Add support for uSD card")
Link: https://lore.kernel.org/r/20201217183341.3186402-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add labels to the cpuN-thermal nodes to allow board files to use
a phandle instead replicating the node hierarchy when adjusting
certain properties.
Due to the 'sustainable-power' property CPU thermal zones are
more likely to need property updates than other SC7180 zones,
hence only labels for CPU zones are added for now.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20210108141648.1.Ia8019b8b303ca31a06752ed6ceb5c3ac50bd1d48@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
sm8250 has a big.LITTLE CPU setup with DynamIQ, so all cores are within
the same CPU cluster and LLC (Last-Level Cache) domain. Define this
topology to help the scheduler make decisions.
Signed-off-by: Danny Lin <danny@kdrag0n.dev>
Link: https://lore.kernel.org/r/20210112013255.415253-1-danny@kdrag0n.dev
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When the BMC150 accelerometer/magnetometer was added to the device tree,
the sensors were working without specifying any regulator supplies,
likely because the regulators were on by default and then never turned off.
For some reason, this is no longer the case for pm8916_l17, which prevents
the sensors from working in some cases.
Now that the bmc150_accel/bmc150_magn drivers can enable necessary
regulators, declare the necessary regulator supplies to make the sensors
work again.
Fixes: 079f81acf1 ("arm64: dts: qcom: msm8916-samsung-a2015: Add accelerometer/magnetometer")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210111175358.97171-1-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Running cpufreq-hw driver on Lenovo Yoga C630 laptop, the following
warning messages will be seen.
[ 3.415340] cpu cpu4: Voltage update failed freq=2841600
[ 3.418755] cpu cpu4: failed to update OPP for freq=2841600
[ 3.422949] cpu cpu4: Voltage update failed freq=2956800
[ 3.427086] cpu cpu4: failed to update OPP for freq=2956800
This is because the cpufreq-hw lookup table of SDM850 provides these two
set-points, but they are missing from OPP table in DT. Let's create
sdm850.dtsi to add the OPP for them, so that the warning will be gone.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210112090640.20062-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based
on the sdm845-mtp DT with the following functionality:
* Touch
* Display
* GPU
* Wlan and Bluetooth
* USB peripheral mode
* Remoteproc
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Link: https://lore.kernel.org/r/20210114203057.64541-2-caleb@connolly.tech
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add interconnect ports for lcdif to set bus capabilities.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add #interconnect-cells on main &noc so that it will probe the interconnect
provider.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add initial support for dynamic frequency scaling of the main NOC
on imx8mq.
Make DDRC the parent of the NOC (using passive governor) so that the
main NOC is automatically scaled together with DDRC by default.
Support for proactive scaling via interconnect will come on top.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a new variant 1 of this board available. It features up to four
SerDes lanes for customer use. Add a new device tree which features just
the basic peripherals. A customer will then have to modify or append to
this device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for audio output over the HDMI output using Tertiary I2S
and LT9611UXC DSI-to-HDMI bridge.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210115024713.92574-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable Compute DSP (cdsp) on QRB5165-RB5 platform and provide firmware
filename used to boot the cdsp.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210115024156.92265-1-dmitry.baryshkov@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Two carveout reserved memory nodes each have been added for each of the
R5F remote processor devices within both the MCU and MAIN domains on the
TI J7200 EVM boards. These nodes are assigned to the respective rproc
device nodes as well. The first region will be used as the DMA pool for
the rproc device, and the second region will furnish the static carveout
regions for the firmware memory.
An additional reserved memory node is also added to reserve a portion of
the DDR memory to be used for performing inter-processor communication
between all the remote processors running RTOS. 8 MB of memory is reserved
for this purpose, and this accounts for all the vrings and vring buffers
between all the possible pairs of remote processors.
The current carveout addresses and sizes are defined statically for each
device. The R5F processors do not have an MMU, and as such require the
exact memory used by the firmwares to be set-aside. The firmware images
do not require any RSC_CARVEOUT entries in their resource tables either
to allocate the memory for firmware memory segments.
NOTE:
1. The R5F1 carveouts are needed only if the R5F cluster is running in
Split (non-LockStep) mode. The reserved memory nodes can be disabled
later on if there is no use-case defined to use the corresponding
remote processor.
2. The J7200 SoCs have no DSPs and one less R5F cluster compared to J721E
SoCs. So, while the carveout memories reserved for the R5F clusters
present on the SoC match to those on J721E, the overall memory map
reserved for firmwares is quite different.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210111184554.6748-4-s-anna@ti.com
Add the required 'mboxes' property to all the R5F processors for the
TI J7200 common processor board. The mailboxes and some shared memory
are required for running the Remote Processor Messaging (RPMsg) stack
between the host processor and each of the R5Fs. The nodes are therefore
added in the common k3-j7200-som-p0.dtsi file so that all of these can
be co-located.
The chosen sub-mailboxes match the values used in the current firmware
images. This can be changed, if needed, as per the system integration
needs after making appropriate changes on the firmware side as well.
Note that any R5F Core1 resources are needed and used only when that
R5F cluster is configured for Split-mode.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210111184554.6748-3-s-anna@ti.com
The J7200 SoCs have 2 dual-core Arm Cortex-R5F processor (R5FSS)
subsystems/clusters. One R5F cluster is present within the MCU
domain (MCU_R5FSS0), and the other one is present within the MAIN
domain (MAIN_R5FSS0). Each of these can be configured at boot time
to be either run in a LockStep mode or in an Asymmetric Multi
Processing (AMP) fashion in Split-mode. These subsystems have 64 KB
each Tightly-Coupled Memory (TCM) internal memories for each core
split between two banks - ATCM and BTCM (further interleaved into
two banks). The TCMs of both Cores are combined in LockStep-mode
to provide a larger 128 KB of memory, but otherwise are functionally
similar to those on J721E SoCs.
Add the DT nodes for both the MCU and MAIN domain R5F cluster/subsystems,
the two R5F cores are added as child nodes to each of the R5F cluster
nodes. The clusters are configured to run in LockStep mode by default,
with the ATCMs enabled to allow the R5 cores to execute code from DDR
with boot-strapping code from ATCM. The inter-processor communication
between the main A72 cores and these processors is achieved through
shared memory and Mailboxes.
The following firmware names are used by default for these cores, and
can be overridden in a board dts file if desired:
MCU R5FSS0 Core0: j7200-mcu-r5f0_0-fw (both in LockStep and Split modes)
MCU R5FSS0 Core1: j7200-mcu-r5f0_1-fw (needed only in Split mode)
MAIN R5FSS0 Core0: j7200-main-r5f0_0-fw (both in LockStep & Split modes)
MAIN R5FSS0 Core1: j7200-main-r5f0_1-fw (needed only in Split mode)
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Link: https://lore.kernel.org/r/20210111184554.6748-2-s-anna@ti.com
The eMMC modules offered for the Pine64 boards are capable of the HS200
eMMC speed mode, when observing the frequency limit of 150 MHz.
Enable that in the DT.
This increases the interface speed from ~80 MB/s to ~120 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-9-andre.przywara@arm.com
The eMMC modules offered for the Pine64 boards are capable of the HS200
eMMC speed mode, when observing the frequency limit of 150 MHz.
Enable that in the DT.
This increases the interface speed from ~80 MB/s to ~120 MB/s.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-8-andre.przywara@arm.com
In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.
Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.
Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.
Fixes: 22be992fae ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com
The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).
Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).
Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.
Fixes: 8f54bd1595 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com
The SD card on the SoPine SoM module is somewhat concealed, so was
originally defined as "non-removable".
However there is a working card-detect pin (tested on two different
SoM versions), and in certain SoM base boards it might be actually
accessible at runtime.
Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the
non-removable flag, even though the SD card slot is perfectly accessible
and usable there. (It turns out that just *my* board has a broken card
detect switch, so I originally thought CD wouldn't work on the LTS.)
Drop the "non-removable" flag to describe the SD card slot properly.
Fixes: c3904a2698 ("arm64: allwinner: a64: add DTSI file for SoPine SoM")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-5-andre.przywara@arm.com
The Pine64-LTS board features a blue status LED on pin PL7.
Describe it in the DT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-4-andre.przywara@arm.com
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: eabb3d424b ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: dc03a047df ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com
Add device nodes for the General Purpose Input/Output (GPIO) block on
the Renesas R-Car V3U (r8a779a0) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210114111117.2214281-1-geert+renesas@glider.be
PineH64 model B has wifi+bt combo module. Wifi is already supported, so
lets add also bluetooth node.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210110211606.3733056-1-jernej.skrabec@siol.net
PinePhone volume keys are connected to the LRADC in the A64. Users may
want to use them to wake the device from sleep. Support this by
declaring the LRADC as a wakeup source.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113040542.34247-4-samuel@sholland.org
The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.
This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).
Tested-by: Vinod Koul <vkoul@kernel.org> #on db845c
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201222001103.3112306-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This commit adds support for deep idling of the entire unified DynamIQ
CPU cluster on sm8150. In this idle state, the LLCC (Last-Level Cache
Controller) is powered off and the AOP (Always-On Processor) enters a
low-power sleep state.
I'm not sure what the per-CPU 0x400000f4 idle state previously
contributed by Qualcomm as the "cluster sleep" state is, but the
downstream kernel has no such state. The real deep cluster idle state
is 0x41000c244, composed of:
Cluster idle state: (0xc24) << 4 = 0xc240
Is reset state: 1 << 30 = 0x40000000
Affinity level: 1 << 24 = 0x1000000
CPU idle state: 0x4 (power collapse)
This setup can be replicated with the PSCI power domain cpuidle driver,
which utilizes OSI to enter cluster idle when the last active CPU
enters idle.
The cluster idle state cannot be used as a plain cpuidle state because
it requires that all CPUs in the cluster are idling.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Danny Lin <danny@kdrag0n.dev>
Link: https://lore.kernel.org/r/20210105201000.913183-1-danny@kdrag0n.dev
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
For a bunch of rails we really don't do anything with them in Linux.
These are things like modem voltage rails that the modem manages these
itself and core rails (like IO rails) that are setup to just
automagically do the right thing by the firmware.
Let's stop even listing those rails in our device tree.
The net result of this is that some of these rails might be able to go
down to a lower voltage or perhaps transition to LPM (low power mode)
sometimes.
Here's a list of what we're doing and why:
* L1A - only goes to SoC and doesn't seem associated with any
particular peripheral. Kernel isn't doing anything with
this. Removing from dts. NET IMPACT: rail might drop from 1.2V to
1.178V and switch to LPM in some cases depending on firmware.
* L2A - only goes to SoC and doesn't seem associated with any
particular peripheral. Kernel isn't doing anything with
this. Removing from dts. NET IMPACT: rail might switch to LPM in
some cases depending on firmware.
* L3A - only goes to SoC and doesn't seem associated with any
particular peripheral. Kernel isn't doing anything with
this. Removing from dts. NET IMPACT: rail might switch to LPM in
some cases depending on firmware.
* L5A - seems to be totally unused as far as I can tell and doesn't
even come off QSIP. Removing from dts.
* L6A - only goes to SoC and doesn't seem associated with any
particular peripheral (I think?). Kernel isn't doing anything with
this. Removing from dts. NET IMPACT: rail might switch to LPM in
some cases depending on firmware.
* L16A - Looks like this is only used for internal RF stuff. Removing
from dts. NET IMPACT: rail might switch to LPM in some cases
depending on firmware.
* L1C - Just goes to WiFi / Bluetooth. Trust how IDP has this set and
put this back at 1.616V min.
* L4C - This goes out to the eSIM among other places. This looks like
it's intended to be for SIM card and modem manages. NET IMPACT:
rail might switch to LPM in some cases depending on firmware.
* L5C - This goes to the physical SIM. This looks like it's intended
to be for SIM card and modem manages. NET IMPACT: rail might drop
from 1.8V to 1.648V and switch to LPM in some cases depending on
firmware.
NOTE: in general for anything which is supposed to be managed by Linux
I still left it all forced to HPM since I'm not 100% sure that all the
needed calls to regulator_set_load() are in place and HPM is safer.
Switching more things to LPM can happen in a future patch.
ALSO NOTE: Power measurements showed no measurable difference after
applying this patch, so perhaps it should be viewed more as a cleanup
than any power savings.
Reviewed-by: Alexandru M Stan <amstan@google.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201207143255.1.Ib92ec35163682dec4b2fbb4bde0785cb6e6dde27@changeid
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
x2 lane PCIe slot in the common processor board is enabled and connected to
j7200 SOM. Add PCIe DT node in common processor board to reflect the
same.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210105151421.23237-7-kishon@ti.com
Add sub-nodes to SERDES0 DT node to represent SERDES0 is connected
to PCIe and QSGMII (multi-link SERDES).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210105151421.23237-6-kishon@ti.com
Add PCIe device tree node (both RC and EP) for the single PCIe
instance present in j7200.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210105151421.23237-5-kishon@ti.com
Add dt node for the single instance of WIZ (SERDES wrapper) and
SERDES module shared by PCIe, CPSW (SGMII/QSGMII) and USB.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210105151421.23237-4-kishon@ti.com
Cadence IP in J721E supports a maximum of 32 outbound regions. However
commit 4e5833884f ("arm64: dts: ti: k3-j721e-main: Add PCIe device
tree nodes") incorrectly added this as 16 outbound regions. Now that
"cdns,max-outbound-regions" is an optional property with default value
as 32, remove "cdns,max-outbound-regions" from endpoint DT node.
(Since this doesn't impact existing functionality, it need not be
backported to older kernels).
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210105151421.23237-2-kishon@ti.com
The RZ/G2 series contain the SPI Multi I/O Bus Controller (RPC-IF).
Add the nodes, but make them disabled by default.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20210102115412.3402059-4-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Per the reference manual for the RZ/G Series, 2nd Generation,
the RZ/G2M, RZ/G2N, and RZ/G2H have a bit that can be set to
choose between a crystal oscillator and an external oscillator.
Because only boards that need this should enable it, it's marked
as disabled by default for backwards compatibility with existing
boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201228202221.2327468-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Beacon EmbeddedWorks is introducing a new kit based on the
RZ/G2H SoC from Renesas.
The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1
cellular radio.
The Baseboard has Ethernet, USB, HDMI, stereo audio in and out,
along with a variety of push buttons and LED's, and support for
a parallel RGB and an LVDS display. It uses the same baseboard
and SOM files as the RZ/G2M and RZ/G2N kits.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-8-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Beacon EmbeddedWorks is introducing a new kit based on the
RZ/G2N SoC from Renesas.
The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1
cellular radio.
The Baseboard has Ethernet, USB, HDMI, stereo audio in and out,
along with a variety of push buttons and LED's, and support for
a parallel RGB and an LVDS display. It uses the same baseboard
and SOM as the RZ/G2M.
This SOM has only 2GB of DDR, and beacon-renesom-som.dtsi contains
the base memory node, so an additional memory node isn't necessary.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-7-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
In preparation for adding new dev kits, move anything specific to the
RZ/G2M from the SOM-level and baseboard-levels and move them to the
kit-level. This allows the SOM and baseboard to be reused with
other SoC's.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-6-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The keys on the baseboard are laid out in an diamond pattern, up, down,
left, right and center. Update the descriptions to make it easier to
read.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-4-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
With the newly added configurable clock options, the audio CODEC can
configure the mclk automatically. Add the reference to the versaclock.
Since the devices on I2C5 can communicate at 400KHz, let's also increase
that too
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-3-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The SoC was expecting two clock sources with different frequencies.
One to support 44.1KHz and one to support 48KHz. With the newly added
ability to configure the programmable clock, configure both clocks.
Assign the rcar-sound clocks to reference the versaclock instead of
the fixed clock.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-2-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When the board was added, clock drivers were being updated done at
the same time to allow the versaclock driver to properly configure
the modes. Unfortunately, the updates were not applied to the board
files at the time they should have been, so do it now.
Signed-off-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/20201224170502.2254683-1-aford173@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development
kits consisting of a GW700x SoM and a Baseboard. Future SoM's such
as the GW701x will create additional combinations.
The GW700x SoM contains:
- i.MX 8M Mini SoC
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor)
- GbE PHY connected to the i.MX 8M Mini FEC
- Power Management IC
The GW71xx Baseboard contains:
- 1x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 1x RJ45 GbE (i.MX 8M Mini FEC)
- I/O connector with 1x-SPI/1x-I2C/1x-UART/4x-GPIO signals
- PCIe Clock generator
- GPS and accelerometer
- 1x USB 2.0 Front Panel connector
- wide range power supply
The GW72xx Baseboard contains:
- 2x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x)
- 1x MicroSD connector
- 1x USB 2.0 Front Panel connector
- 1x SPI connector
- 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of:
RS232 w/ flow-control, RS485, RS422
- PCIe Clock generator
- GPS and accelerometer
- Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
- I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C
- wide range power supply
The GW73xx Baseboard contains:
- 3x MiniPCIe Socket with USB2.0, PCIe, and SIM
- 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x)
- 1x MicroSD connector
- 1x USB 2.0 Front Panel connector
- 1x SPI connector
- 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of:
RS232 w/ flow-control, RS485, RS422
- WiFi/BT
- PCIe Clock generator
- GPS and accelerometer
- Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S)
- I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C
- wide range power supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to be able to use NVMEM APIs to read soc unique ID, add the
nvmem data cell and name for nvmem-cells to the "soc" node, and add a
nvmem node which provides soc unique ID to efuse@30350000.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add compatible string to .dtsi files for binding of imx8_soc_info and
device.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is a workaround for a hardware bug in the r3 revision that basically would
stop the system due to traffic on the i2c1 bus. A cpu voltage change would
trigger such traffic and that's what is avoided in order to work around it.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order for the touchscreen interrupt line to work, describe it properly.
Otherwise it can work if defaults are ok, but we cannot be sure.
Fixes: 8f0216b006 ("arm64: dts: Add a device tree for the Librem 5 phone")
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This makes sure the clock tree setup for the dphy is not dependent on
other components.
Without this change bringing up the display can fail like
kernel: phy phy-30a00300.dphy.2: Invalid CM/CN/CO values: 165/217/1
kernel: phy phy-30a00300.dphy.2: for hs_clk/ref_clk=451656000/593999998 ~ 165/217
if LCDIF doesn't set up that part of the clock tree first. This was
noticed when testing the Librem 5 devkit with defconfig. It doesn't
happen when modules are built in.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The wlf,wm8962 driver does not use the clock-names property.
Drop it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board has it's own RTC chip which is backed by the (optional)
battery and hence preserves data/time on poweroff when that is inserted.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
BUCK3 needs a regulator-enable-ramp-delay since otherwise the board
freezes on etnaviv probe. With this pgc_gpu suspends and resumes as
expected. This must have been always broken since gpcv2 support was
enabled.
We also enable all the regulators needed for Deep Sleep Mode (DSM) as
always-on:
- VDD_SOC supplied by BUCK1
- VDDA_1P8 supplied by BUCK7
- VDDA_0P9 supplied by LDO4
- VDDA_DRAM supplied by LDO3
- NVCC_DRAM supplied by BUCK8
- VDD_DRAM supplied by BUCK5
Finally LDO5 and LDO6 provide VDD_PHY_1V8 and VDD_PHY_0V9 used by the
SOCs MIPI, HDMI and USB IP cores. While we would in theory be able to
turn these off (and I've tested that or LDO6 and mipi with USB disabled)
it is of little practical use atm since USB doesn't runtime suspend so
let's revisit this at a later point.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The offset of the reset request register is 0, the absolute address is
0x1e60000. Boards without PSCI support will fail to perform a reset:
[ 26.734700] reboot: Restarting system
[ 27.743259] Unable to restart system
[ 27.746845] Reboot failed -- System halted
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It recently became apparent that the lack of a 'device_type = "pci"'
in the PCIe root complex node for rk3399 is a violation of the PCI
binding, as documented in IEEE Std 1275-1994. Changes to the kernel's
parsing of the DT made such violation fatal, as drivers cannot
probe the controller anymore.
Add the missing property makes the PCIe node compliant. While we
are at it, drop the pointless linux,pci-domain property, which only
makes sense when there are multiple host bridges.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200815125112.462652-3-maz@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds 'disabled' SPDIF sound node and related settings
for rk3399-rockpro64.
There are 2 reasons:
- All RK3399 dma-bus channels have been already used by I2S0/1/2
- RockPro64 does not have SPDIF optical nor coaxial connector,
just have 3pins
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20200810091619.3170534-1-katsuhiro@katsuster.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch enables HDMI sound (I2S0) and Analog sound (I2S1) which
are defined in rk3328.dtsi, and replace SPDIF nodes.
We can use SPDIF pass-through with suitable ALSA settings and on
mpv or other media players.
- Settings: https://github.com/LibreELEC/LibreELEC.tv/blob/master/projects/Rockchip/filesystem/usr/share/alsa/cards/SPDIF.conf
- Ex.: mpv foo.ac3 --audio-spdif=ac3 --audio-device='alsa/SPDIF.pcm.iec958.0:SPDIF'
[Why use simple-audio-card for SPDIF?]
For newly adding nodes, ASoC guys recommend to use audio-graph-card.
But all other sound nodes for rk3328 have already been defined by
simple-audio-card. In this time, I chose for consistent sound nodes.
[DMA allocation problem]
After this patch is applied, UART2 will fail to allocate DMA resources
but UART driver can work fine without DMA.
This error is related to the DMAC of rk3328 (pl330 or compatible).
DMAC connected to 16 DMA sources. Each sources have ID number that is
called 'Req number' in rk3328 TRM. After this patch is applied total 7
of DMA sources will be activated as follows:
| Req number | Source | Required |
| | | channels |
|------------+--------+-----------|
| 8, 9 | SPI0 | 2ch |
| 11, 12 | I2S0 | 2ch |
| 14, 15 | I2S1 | 2ch |
| 10 | SPDIF | 1ch |
|------------+--------+-----------|
| | Total | 7ch |
|------------+--------+-----------|
| 6, 7 | UART2 | 2ch | -> cannot get DMA channels
Due to rk3328 DMAC specification we can use max 8 channels at same
time. If SPI0/I2S0/I2S1/SPDIF will be activated by this patch,
required DMAC channels reach to 7. So the last two channels (for
UART2) cannot get DMA resources.
Virt-dma mechanism for pl0330 DMAC driver is needed to fix this
problem.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20200802154231.2639186-1-katsuhiro@katsuster.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On Pinebook Pro laptops with an NVMe SSD installed, prevent random
crashes in the NVMe driver by not attempting to use a PCIe link speed
higher than that supported by the RK3399 SoC.
See commit 712fa17772 ("arm64: dts: rockchip: add max-link-speed for
rk3399").
Fixes: 5a65505a69 ("arm64: dts: rockchip: Add initial support for Pinebook Pro")
Signed-off-by: Simon South <simon@simonsouth.net>
Link: https://lore.kernel.org/r/20200930185627.5918-1-simon@simonsouth.net
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the conversion of syscon.yaml minItems for compatibles
was set to 2. Current Rockchip dtsi files only use "syscon" for
QoS registers. Add Rockchip QoS compatibles for px30
to reduce notifications produced with:
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201206103711.7465-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
With the conversion of syscon.yaml minItems for compatibles
was set to 2. Current Rockchip dtsi files only use "syscon" for
QoS registers. Add Rockchip QoS compatibles for rk3399
to reduce notifications produced with:
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20201206103711.7465-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The vop-mmu shares the irq with its matched vop but not the vpu.
Fixes: 7053e06b14 ("arm64: dts: rockchip: add core dtsi file for PX30 SoCs")
Signed-off-by: Sandy Huang <hjc@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20210108110627.3231226-1-heiko@sntech.de
These are a small number of bug fixes that all came in before or during
the merge window, most for the omap platform:
- One boot regression fix for Nokia N9 (OMAP3).
- Two small defconfig changes for omap2, to reflect changes in drivers
- Warning fixes for DT issues on omap2, picoxcell and bitmap SoCs.
The picoxcell platform will be removed in v5.12, but fixing it
first makes it easier to backport to the fix to stable kernels
and get a clean build with new dtc versions
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=gv6R
-----END PGP SIGNATURE-----
Merge tag 'arm-fixes-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"These are a small number of bug fixes that all came in before or
during the merge window, most for the omap platform:
- One boot regression fix for Nokia N9 (OMAP3).
- Two small defconfig changes for omap2, to reflect changes in
drivers
- Warning fixes for DT issues on omap2, picoxcell and bitmap SoCs.
The picoxcell platform will be removed in v5.12, but fixing it
first makes it easier to backport to the fix to stable kernels and
get a clean build with new dtc versions"
* tag 'arm-fixes-5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: picoxcell: fix missing interrupt-parent properties
ARM: dts: ux500/golden: Set display max brightness
arm64: dts: bitmain: Use generic "ngpios" rather than "snps,nr-gpios"
ARM: omap2: pmic-cpcap: fix maximum voltage to be consistent with defaults on xt875
ARM: omap2plus_defconfig: enable SPI GPIO
ARM: OMAP2+: omap_device: fix idling of devices during probe
ARM: dts: OMAP3: disable AES on N950/N9
ARM: omap2plus_defconfig: drop unused POWER_AVS option
Unlike most MSM8916 boards, samsung-a5u uses WCN3660B instead of
WCN3620 to support the 5 GHz band additionally.
WCN3660B has similar requirements as WCN3620, but it needs the XO
clock to run at 48 MHz instead of 19.2 MHz. So far it was possible
to describe that configuration using the qcom,wcn3680 compatible.
However, as of commit 8490987bdb ("wcn36xx: Hook and identify RF_IRIS_WCN3680"),
the wcn36xx driver will now use the qcom,wcn3680 compatible
to enable functionality specific to WCN3680. In particular,
WCN3680 supports 802.11ac, which is not available in WCN3660B.
Use the new qcom,wcn3660b compatible to describe the chip properly.
Fixes: 0d70519991 ("arm64: dts: msm8916-samsung-a5u: Override iris compatible")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106102134.59801-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add sound-spdif card nodes which are supported on imx8mn-evk board.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sound-wm8524 card nodes which are supported on imx8mn-evk board.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure clock rate for audio plls. audio pll1 is used
as parent clock for clocks that is multiple of 8kHz.
audio pll2 is used as parent clock for clocks that is
multiple of 11kHz.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Error log:
sysfs: cannot create duplicate filename '/bus/platform/devices/30000000.bus'
The spba bus name is duplicate with aips bus name.
Refine spba bus name to fix this issue.
Fixes: 970406eaef ("arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All revisions of the PinePhone share most of the hardware.
This patch makes it easier to detect PinePhone hardware without
having to check for each possible revision.
Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201230104205.5592-1-me@dylanvanassche.be
As the original PineTab DT (which uses sun50i-a64-pinetab name) is only
for development samples, document this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201224024138.19422-1-icenowy@aosc.io
PineTabs since Early Adopter batch will use a new LCD panel.
Add device tree for PineTab with the new panel.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201224024001.19248-2-icenowy@aosc.io
Like other Qualcomm SoCs, sm8150 exposes CPU and cluster idle states
through PSCI. Define the idle states to save power when the CPU is not
in active use.
These idle states, latency, and residency values match the downstream
4.14 kernel from Qualcomm as of LA.UM.8.1.r1-15600-sm8150.0.
It's worth noting that the CPU has an additional C3 power collapse idle
state between WFI and rail power collapse (with PSCI mode 0x40000003),
but it is not officially used in downstream kernels due to "thermal
throttling issues."
Signed-off-by: Danny Lin <danny@kdrag0n.dev>
Link: https://lore.kernel.org/r/20201221002907.2870059-3-danny@kdrag0n.dev
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
sm8150 has a big.LITTLE CPU setup with DynamIQ, so all cores are within
the same CPU cluster and LLC (Last-Level Cache) domain. Define this
topology to help the scheduler make decisions.
Signed-off-by: Danny Lin <danny@kdrag0n.dev>
Link: https://lore.kernel.org/r/20201221002907.2870059-2-danny@kdrag0n.dev
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The eSDHC driver has converted to use asynchronous probe.
Let's use fixed index mmcN for eSDHC controllers, so that
we can ignore the effect on usage, and avoid problem on
previous use cases with fixed index mmcblkN.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
