Previously, the ACPI_COMPANION() of a pci_dev was usually set by
acpi_bind_one() in this path:
pci_device_add
pci_configure_device
pci_init_capabilities
device_add
device_platform_notify
acpi_platform_notify
acpi_device_notify # KOBJ_ADD
acpi_bind_one
ACPI_COMPANION_SET
However, things like pci_configure_device() and pci_init_capabilities()
that run before device_add() need the ACPI_COMPANION, e.g.,
acpi_pci_bridge_d3() uses a _DSD method to learn about D3 support. These
places had special-case code to manually look up the ACPI_COMPANION.
Set the ACPI_COMPANION earlier, in pci_setup_device(), so it will be
available while configuring the device. This covers both paths to creating
pci_dev objects:
pci_scan_single_device # for normal non-SR-IOV devices
pci_scan_device
pci_setup_device
pci_set_acpi_fwnode
pci_device_add
pci_iov_add_virtfn # for SR-IOV virtual functions
pci_setup_device
pci_set_acpi_fwnode
Also move the OF fwnode setup to the same spot.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210817180500.1253-8-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
"reset_fn" indicates whether the device supports any reset mechanism.
Remove the use of reset_fn in favor of the reset_methods array that tracks
supported reset mechanisms of a device and their ordering.
The octeon driver incorrectly used reset_fn to detect whether the device
supports FLR or not. Use pcie_reset_flr() to probe whether it supports FLR.
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-5-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Add reset_methods[] in struct pci_dev to keep track of reset mechanisms
supported by the device and their ordering.
Refactor probing and reset functions to take advantage of calling
convention of reset functions.
Co-developed-by: Alex Williamson <alex.williamson@redhat.com>
Link: https://lore.kernel.org/r/20210817180500.1253-4-ameynarkhede03@gmail.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Add a new member called devcap in struct pci_dev for caching the PCIe
Device Capabilities register to avoid reading PCI_EXP_DEVCAP multiple
times.
Refactor pcie_has_flr() to use cached device capabilities.
Link: https://lore.kernel.org/r/20210817180500.1253-2-ameynarkhede03@gmail.com
Signed-off-by: Amey Narkhede <ameynarkhede03@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Now that struct pci_vpd is really small, simplify the code by embedding
struct pci_vpd directly in struct pci_dev instead of dynamically allocating
it.
Link: https://lore.kernel.org/r/d898489e-22ba-71f1-2f31-f1a78dc15849@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Coalesce host bridge apertures so we can allocate large BARs that cross
contiguous apertures (Kai-Heng Feng)
* pci/resource:
PCI: Coalesce host bridge contiguous apertures
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into usb-next
We want the usb fixes in here as well, and this resolves some merge
issues with:
drivers/usb/dwc3/debugfs.c
drivers/usb/dwc3/gadget.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6279504141 ("PCI: enhance physical slot debug information") added
a debug print on releasing the PCI slot and another message on destroying
it. There is however no debug print on releasing the PCI device structure
itself and even with closely looking at the kernel log during hotplug
testing, I overlooked several missing pci_dev_put() calls for way too long.
Add a debug print in pci_release_dev() making it much easier to spot when
the PCI device structure is not released when it is supposed to be.
Link: https://lore.kernel.org/r/20210311132312.2882425-1-schnelle@linux.ibm.com
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
A PCI device is "external_facing" if it's a Root Port with the ACPI
"ExternalFacingPort" property or if it has the DT "external-facing"
property. We consider everything downstream from such a device to
be removable by user.
We're mainly concerned with consumer platforms with user accessible
Thunderbolt ports that are vulnerable to DMA attacks, and we expect those
ports to be identified by firmware as "ExternalFacingPort". Devices in
traditional hotplug slots can technically be removed, but the expectation
is that unless the port is marked with "ExternalFacingPort", such devices
are less accessible to user / may not be removed by end user, and thus not
exposed as "removable" to userspace.
This can be used to implement userspace policies tailored for
user removable devices. Eg usage:
https://chromium-review.googlesource.com/c/chromiumos/platform2/+/2591812https://chromium-review.googlesource.com/c/chromiumos/platform2/+/2795038
(code uses such an attribute to remove external PCI devices or disable
features on them as needed by the policy desired)
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Link: https://lore.kernel.org/r/20210524171812.18095-2-rajatja@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 9ec37efb87 ("PCI/MSI: Make pci_host_common_probe() declare
its reliance on MSI domains"), platforms that rely on the "msi-map"
device-tree property don't get MSIs anymore.
On the Arm Fast Model for example [1], the host bridge doesn't have a
"msi-parent" property since it doesn't itself generate MSIs, and so doesn't
get a MSI domain. It has an "msi-map" property instead to describe MSI
controllers of child devices. As a result, due to the new msi_domain check
in pci_register_host_bridge(), the whole bus gets PCI_BUS_FLAGS_NO_MSI.
Check whether the root complex has an "msi-map" property before giving
up on MSIs.
[1] arch/arm64/boot/dts/arm/fvp-base-revc.dts
Fixes: 9ec37efb87 ("PCI/MSI: Make pci_host_common_probe() declare its reliance on MSI domains")
Link: https://lore.kernel.org/r/20210510173129.750496-1-jean-philippe@linaro.org
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
- Convert tegra to MSI domains (Marc Zyngier)
- Use rcar controller address as MSI doorbell instead of allocating a page
(Marc Zyngier)
- Convert rcar to MSI domains (Marc Zyngier)
- Use xilinx port structure as MSI doorbell instead of allocating a page
(Marc Zyngier)
- Convert xilinx to MSI domains (Marc Zyngier)
- Remove unused Hyper-V msi_controller structure (Marc Zyngier)
- Remove unused PCI core msi_controller support (Marc Zyngier)
- Remove struct msi_controller (Marc Zyngier)
- Remove unused default_teardown_msi_irqs() (Marc Zyngier)
- Let host bridges declare their reliance on MSI domains (Marc Zyngier)
- Make pci_host_common_probe() declare its reliance on MSI domains (Marc
Zyngier)
- Advertise mediatek lack of built-in MSI handling (Thomas Gleixner)
- Document ways of ending up with NO_MSI (Marc Zyngier)
- Refactor HT advertising of NO_MSI flag (Marc Zyngier)
* remotes/lorenzo/pci/msi:
PCI: Refactor HT advertising of NO_MSI flag
PCI/MSI: Document the various ways of ending up with NO_MSI
PCI: mediatek: Advertise lack of built-in MSI handling
PCI/MSI: Make pci_host_common_probe() declare its reliance on MSI domains
PCI/MSI: Let PCI host bridges declare their reliance on MSI domains
PCI/MSI: Kill default_teardown_msi_irqs()
PCI/MSI: Kill msi_controller structure
PCI/MSI: Drop use of msi_controller from core code
PCI: hv: Drop msi_controller structure
PCI: xilinx: Convert to MSI domains
PCI: xilinx: Don't allocate extra memory for the MSI capture address
PCI: rcar: Convert to MSI domains
PCI: rcar: Don't allocate extra memory for the MSI capture address
PCI: tegra: Convert to MSI domains
There is a whole class of host bridges that cannot know whether
MSIs will be provided or not, as they rely on other blocks
to provide the MSI functionnality, using MSI domains. This is
the case for example on systems that use the ARM GIC architecture.
Introduce a new attribute ('msi_domain') indicating that implicit
dependency, and use this property to set the NO_MSI flag when
no MSI domain is found at probe time.
Link: https://lore.kernel.org/r/20210330151145.997953-11-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
As there is no driver using msi_controller, we can now safely
remove its use from the PCI probe code.
Link: https://lore.kernel.org/r/20210330151145.997953-8-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
In pci_scan_device(), if pci_setup_device() fails for any reason, the code
will not release device's of_node by calling pci_release_of_node(). Fix
that by calling the release function.
Fixes: 98d9f30c82 ("pci/of: Match PCI devices to OF nodes dynamically")
Link: https://lore.kernel.org/r/20210124232826.1879-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
- Disable MSI for broken Pericom PCIe-USB adapter (Andy Shevchenko)
- Move MSI/MSI-X init to msi.c (Bjorn Helgaas)
- Move MSI/MSI-X flags updaters to msi.c (Bjorn Helgaas)
- Warn if we assign 64-bit MSI address to device that only supports 32-bit
MSI (Vidya Sagar)
* pci/msi:
PCI/MSI: Set device flag indicating only 32-bit MSI support
PCI/MSI: Move MSI/MSI-X flags updaters to msi.c
PCI/MSI: Move MSI/MSI-X init to msi.c
PCI: Use predefined Pericom Vendor ID
PCI: Disable MSI for Pericom PCIe-USB adapter
- Stop writing AER Capability when we don't own it (Sean V Kelley)
- Bind RCEC devices to the Port driver (Qiuxu Zhuo)
- Cache the RCEC RA Capability offset (Sean V Kelley)
- Add pci_walk_bridge() (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs with RCECs (Sean V Kelley)
- Recover from RCiEP AER errors (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() for RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
* pci/err:
PCI/AER: Add RCEC AER error injection support
PCI/PME: Add pcie_walk_rcec() to RCEC PME handling
PCI/AER: Add pcie_walk_rcec() to RCEC AER handling
PCI/ERR: Recover from RCiEP AER errors
PCI/ERR: Add pcie_link_rcec() to associate RCiEPs
PCI/ERR: Recover from RCEC AER errors
PCI/ERR: Clear AER status only when we control AER
PCI/ERR: Add pci_walk_bridge() to pcie_do_recovery()
PCI/ERR: Avoid negated conditional for clarity
PCI/ERR: Use "bridge" for clarity in pcie_do_recovery()
PCI/ERR: Simplify by computing pci_pcie_type() once
PCI/ERR: Simplify by using pci_upstream_bridge()
PCI/ERR: Rename reset_link() to reset_subordinates()
PCI/ERR: Cache RCEC EA Capability offset in pci_init_capabilities()
PCI/ERR: Bind RCEC devices to the Root Port driver
PCI/AER: Write AER Capability only when we control it
Move pci_msi_setup_pci_dev(), which disables MSI and MSI-X interrupts, from
probe.c to msi.c so it's with all the other MSI code and more consistent
with other capability initialization. This means we must compile msi.c
always, even without CONFIG_PCI_MSI, so wrap the rest of msi.c in an #ifdef
and adjust the Makefile accordingly. No functional change intended.
Link: https://lore.kernel.org/r/20201203185110.1583077-2-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Extend support for Root Complex Event Collectors by decoding and caching
the RCEC Endpoint Association Extended Capabilities when enumerating. Use
that cached information for later error source reporting. See PCIe r5.0,
sec 7.9.10.
Co-developed-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-4-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
PCIe r6.0, sec 7.5.3.18, defines a new 64.0 GT/s bit in the Supported Link
Speeds Vector of Link Capabilities 2.
This patch does not affect the speed of the link, which should be
negotiated automatically by the hardware; it only adds decoding when
showing the speed to the user.
Decode this new speed. Previously, reading the speed of a link operating
at this speed showed "Unknown speed" instead of "64.0 GT/s".
Link: https://lore.kernel.org/r/aaaab33fe18975e123a84aebce2adb85f44e2bbe.1605739760.git.gustavo.pimentel@synopsys.com
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
- Fix designware-ep Header Type check (Hou Zhiqiang)
- Use DBI accessors instead of own config accessors (Rob Herring)
- Allow overriding bridge pci_ops (Rob Herring)
- Allow root and child buses to have different pci_ops (Rob Herring)
- Add default dwc pci_ops.map_bus (Rob Herring)
- Use pci_ops for root config space accessors in al, exynos, histb,
keystone, kirin, meson, tegra (Rob Herring)
- Remove dwc own/other config accessor ops (Rob Herring)
- Use generic config accessors in dwc (Rob Herring)
- Also call .add_bus() callback for root bus (Rob Herring)
- Convert keystone .scan_bus() callback to use pci_ops.add_bus (Rob
Herring)
- Convert dwc to use pci_host_probe() (Rob Herring)
- Remove dwc root_bus pointer (Rob Herring)
- Remove storing of PCI resources in dwc-specific structs (Rob Herring)
- Simplify config space handling (Rob Herring)
- Drop keystone duplicated DT num-viewport handling (Rob Herring)
- Check CONFIG_PCI_MSI in dw_pcie_msi_init() instead of duplicating it in
all the drivers (Rob Herring)
- Remove imx6 duplicate PCIE_LINK_WIDTH_SPEED_CONTROL definition (Rob
Herring)
- Add dwc num_lanes for use when it's lacking from DT (Rob Herring)
- Ensure "Fast Link Mode" simulation environment setting is cleared (Rob
Herring)
- Drop meson duplicate number of lanes setup (Rob Herring)
- Drop meson unnecessary RC config space init (Rob Herring)
- Rework meson config and dwc port logic register accesses (Rob Herring)
- Use common PCI register definitions in imx6 and qcom (Rob Herring)
- Search for DesignWare PCIe Capability instead of hard-coding its location
(Rob Herring)
- Use common DesignWare register definitions in tegra (Rob Herring)
- Drop keystone unused DBI2 code (Rob Herring)
- Make dwc ATU accessors private (Rob Herring)
- Centralize link gen setting in dwc (Rob Herring)
- Set PORT_LINK_DLL_LINK_EN in common dwc setup code (Rob Herring)
- Drop intel-gw unnecessary DT 'device_type' checking (Rob Herring)
- Move intel-gw PCI_CAP_ID_EXP discovery to the single place it's used (Rob
Herring)
- Drop intel-gw unused max_width (Rob Herring)
- Move N_FTS (fast training sequence) setup to common dwc setup (Rob
Herring)
- Convert spear13xx, tegra194 to use DBI accessors (Rob Herring)
- Add multiple PFs support for DWC (Xiaowei Bao)
- Add MSI-X doorbell mode for endpoint mode (Xiaowei Bao)
- Update MSI/MSI-X capability management for endpoints (Xiaowei Bao)
- Add layerscape ls1088a and ls2088a compatible strings (Xiaowei Bao)
- Update layerscape MSI/MSI-X management (Xiaowei Bao)
- Use doorbell to support MSI-X on layerscape (Xiaowei Bao)
- Add layerscape endpoint mode support for ls1088a and ls2088a (Xiaowei
Bao)
- Add layerscape ls1088a node to DT (Xiaowei Bao)
- Add Freescale/Layerscape ls1088a to endpoint test (Xiaowei Bao)
- Add endpoint test driver data for Layerscape PCIe controllers (Hou
Zhiqiang)
- Fix 'cast truncates bits from constant value' warning (Gustavo Pimentel)
- Add uniphier iATU register description (Kunihiko Hayashi)
- Add common iATU register support (Kunihiko Hayashi)
- Remove keystone iATU register mapping in favor of generic dwc support
(Kunihiko Hayashi)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Fix MSI page leakage in suspend/resume (Jisheng Zhang)
- Check whether link is up before attempting config access (best-effort fix
even though it's racy) (Hou Zhiqiang)
* remotes/lorenzo/pci/dwc:
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI: dwc: Fix MSI page leakage in suspend/resume
PCI: dwc: Skip PCIE_MSI_INTR0* programming if MSI is disabled
PCI: keystone: Remove iATU register mapping
PCI: dwc: Add common iATU register support
dt-bindings: PCI: uniphier-ep: Add iATU register description
dt-bindings: PCI: uniphier: Add iATU register description
PCI: dwc: Fix 'cast truncates bits from constant value'
misc: pci_endpoint_test: Add driver data for Layerscape PCIe controllers
misc: pci_endpoint_test: Add LS1088a in pci_device_id table
PCI: layerscape: Add EP mode support for ls1088a and ls2088a
PCI: layerscape: Modify the MSIX to the doorbell mode
PCI: layerscape: Modify the way of getting capability with different PEX
PCI: layerscape: Fix some format issue of the code
dt-bindings: pci: layerscape-pci: Add compatible strings for ls1088a and ls2088a
PCI: designware-ep: Modify MSI and MSIX CAP way of finding
PCI: designware-ep: Move the function of getting MSI capability forward
PCI: designware-ep: Add the doorbell mode of MSI-X in EP mode
PCI: designware-ep: Add multiple PFs support for DWC
PCI: dwc: Use DBI accessors
PCI: dwc: Move N_FTS setup to common setup
PCI: dwc/intel-gw: Drop unused max_width
PCI: dwc/intel-gw: Move getting PCI_CAP_ID_EXP offset to intel_pcie_link_setup()
PCI: dwc/intel-gw: Drop unnecessary checking of DT 'device_type' property
PCI: dwc: Set PORT_LINK_DLL_LINK_EN in common setup code
PCI: dwc: Centralize link gen setting
PCI: dwc: Make ATU accessors private
PCI: dwc: Remove read_dbi2 code
PCI: dwc/tegra: Use common Designware port logic register definitions
PCI: dwc: Remove hardcoded PCI_CAP_ID_EXP offset
PCI: dwc/qcom: Use common PCI register definitions
PCI: dwc/imx6: Use common PCI register definitions
PCI: dwc/meson: Rework PCI config and DW port logic register accesses
PCI: dwc/meson: Drop unnecessary RC config space initialization
PCI: dwc/meson: Drop the duplicate number of lanes setup
PCI: dwc: Ensure FAST_LINK_MODE is cleared
PCI: dwc: Add a 'num_lanes' field to struct dw_pcie
PCI: dwc/imx6: Remove duplicate define PCIE_LINK_WIDTH_SPEED_CONTROL
PCI: dwc: Check CONFIG_PCI_MSI inside dw_pcie_msi_init()
PCI: dwc/keystone: Drop duplicated 'num-viewport'
PCI: dwc: Simplify config space handling
PCI: dwc: Remove storing of PCI resources
PCI: dwc: Remove root_bus pointer
PCI: dwc: Convert to use pci_host_probe()
PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus
PCI: Also call .add_bus() callback for root bus
PCI: dwc: Use generic config accessors
PCI: dwc: Remove dwc specific config accessor ops
PCI: dwc: histb: Use pci_ops for root config space accessors
PCI: dwc: exynos: Use pci_ops for root config space accessors
PCI: dwc: kirin: Use pci_ops for root config space accessors
PCI: dwc: meson: Use pci_ops for root config space accessors
PCI: dwc: tegra: Use pci_ops for root config space accessors
PCI: dwc: keystone: Use pci_ops for config space accessors
PCI: dwc: al: Use pci_ops for child config space accessors
PCI: dwc: Add a default pci_ops.map_bus for root port
PCI: dwc: Allow overriding bridge pci_ops
PCI: dwc: Use DBI accessors instead of own config accessors
PCI: Allow root and child buses to have different pci_ops
PCI: designware-ep: Fix the Header Type check
Save the L1 Substates Capability pointer in struct pci_dev. Then we don't
have to keep track of it in the struct aspm_register_info and struct
pcie_link_state, which makes the code easier to read. No functional change
intended.
[bhelgaas: split to a separate patch]
Link: https://lore.kernel.org/r/20201015193039.12585-8-helgaas@kernel.org
Signed-off-by: Saheed O. Bolarinwa <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Similar to pcibios_add_bus(), call pci_ops.add_bus() when the root bus
is added. This allows host bridge drivers to do any setup requiring a
bus pointer.
There are currently no .add_bus() callbacks, so this is safe to do.
Link: https://lore.kernel.org/r/20200821035420.380495-15-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PCI host bridges often have different ways to access the root and child
bus config spaces. The host bridge drivers have invented their own
abstractions to handle this. Let's support having different root and
child bus pci_ops so these per driver abstractions can be removed.
Link: https://lore.kernel.org/r/20200821035420.380495-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
- Use pci_host_bridge.windows list directly instead of splicing in a
temporary list for cadence, mvebu, host-common (Rob Herring)
- Use pci_host_probe() instead of open-coding all the pieces for altera,
brcmstb, iproc, mobiveil, rcar, rockchip, tegra, v3, versatile, xgene,
xilinx, xilinx-nwl (Rob Herring)
- Convert to devm_platform_ioremap_resource_byname() instead of open-coding
platform_get_resource_byname() and devm_ioremap_resource() for altera,
cadence, mediatek, rockchip, tegra, xgene (Dejin Zheng)
- Convert to devm_platform_ioremap_resource() instead of open-coding
platform_get_resource() and devm_ioremap_resource() for aardvark,
brcmstb, exynos, ftpci100, versatile (Dejin Zheng)
- Remove redundant error messages from devm_pci_remap_cfg_resource()
callers (Dejin Zheng)
- Drop useless PCI_ENABLE_PROC_DOMAINS from versatile driver (Rob Herring)
- Default host bridge parent device to the platform device (Rob Herring)
- Drop unnecessary zeroing of host bridge fields (Rob Herring)
- Use pci_is_root_bus() instead of tracking root bus number separately in
aardvark, designware (imx6, keystone, designware-host), mobiveil,
xilinx-nwl, xilinx, rockchip, rcar (Rob Herring)
- Set host bridge bus number in pci_scan_root_bus_bridge() instead of each
driver for aardvark, designware-host, host-common, mediatek, rcar, tegra,
v3-semi (Rob Herring)
- Use bridge resources instead of parsing DT 'ranges' again for cadence
(Rob Herring)
- Remove private bus number and range from cadence (Rob Herring)
- Use devm_pci_alloc_host_bridge() to simplify rcar (Rob Herring)
- Use struct pci_host_bridge.windows list directly rather than a temporary
(Rob Herring)
- Reduce OF "missing non-prefetchable window" from error to warning message
(Rob Herring)
- Convert rcar-gen2 from old Arm-specific pci_common_init_dev() to new
arch-independent interfaces (Rob Herring)
- Move DT resource setup into devm_pci_alloc_host_bridge() (Rob Herring)
- Set bridge map_irq and swizzle_irq to default functions; drivers that
don't support legacy IRQs (iproc) need to undo this (Rob Herring)
* pci/host-probe-refactor:
PCI: Set bridge map_irq and swizzle_irq to default functions
PCI: Move DT resource setup into devm_pci_alloc_host_bridge()
PCI: rcar-gen2: Convert to use modern host bridge probe functions
PCI: of: Reduce missing non-prefetchable memory region to a warning
PCI: rcar: Use struct pci_host_bridge.windows list directly
PCI: rcar: Use devm_pci_alloc_host_bridge()
PCI: cadence: Remove private bus number and range storage
PCI: cadence: Use bridge resources for outbound window setup
PCI: Move setting pci_host_bridge.busnr out of host drivers
PCI: rcar: Use pci_is_root_bus() to check if bus is root bus
PCI: rockchip: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx: Use pci_is_root_bus() to check if bus is root bus
PCI: xilinx-nwl: Use pci_is_root_bus() to check if bus is root bus
PCI: mobiveil: Use pci_is_root_bus() to check if bus is root bus
PCI: designware: Use pci_is_root_bus() to check if bus is root bus
PCI: aardvark: Use pci_is_root_bus() to check if bus is root bus
PCI: Drop unnecessary zeroing of bridge fields
PCI: Set default bridge parent device
PCI: versatile: Drop flag PCI_ENABLE_PROC_DOMAINS
PCI: controller: Remove duplicate error message
PCI: controller: Convert to devm_platform_ioremap_resource()
PCI: controller: Convert to devm_platform_ioremap_resource_byname()
PCI: xilinx: Use pci_host_probe() to register host
PCI: xilinx-nwl: Use pci_host_probe() to register host
PCI: rockchip: Use pci_host_probe() to register host
PCI: rcar: Use pci_host_probe() to register host
PCI: iproc: Use pci_host_probe() to register host
PCI: altera: Use pci_host_probe() to register host
PCI: xgene: Use pci_host_probe() to register host
PCI: versatile: Use pci_host_probe() to register host
PCI: v3: Use pci_host_probe() to register host
PCI: tegra: Use pci_host_probe() to register host
PCI: mobiveil: Use pci_host_probe() to register host
PCI: brcmstb: Use pci_host_probe() to register host
PCI: host-common: Use struct pci_host_bridge.windows list directly
PCI: mvebu: Use struct pci_host_bridge.windows list directly
PCI: cadence: Use struct pci_host_bridge.windows list directly
# Conflicts:
# drivers/pci/controller/cadence/pcie-cadence-host.c
Now that pci_parse_request_of_pci_ranges() callers just setup
pci_host_bridge.windows and dma_ranges directly and don't need the bus
range returned, we can just initialize them when allocating the
pci_host_bridge struct.
With this, pci_parse_request_of_pci_ranges() becomes a static function.
Link: https://lore.kernel.org/r/20200722022514.1283916-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Announce the device, e.g.,
pci 0000:00:00.0: [8086:5910] type 00 class 0x060000
after running early fixups, so the log message reflects any device type or
class code fixups.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1595833615-8049-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Most host drivers only parse the DT bus range to set the root bus number
in pci_host_bridge.busnr. The ones that don't set busnr are buggy in
that they ignore what's in DT. Let's set busnr in pci_scan_root_bus_bridge()
where we already check for the bus resource and remove setting it in
host drivers.
Link: https://lore.kernel.org/r/20200722022514.1283916-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-tegra@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
The host bridge's parent device is always the platform device. As we
already have a pointer to it in the devres functions, let's initialize
the parent device. Drivers can still override the parent if desired.
Link: https://lore.kernel.org/r/20200722022514.1283916-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Currently the ACS capability is being looked up at a number of places. Read
and store it once at enumeration so that it can be used by all later. No
functional change intended.
Link: https://lore.kernel.org/r/20200707224604.3737893-2-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Clarify that platform_get_irq() should never return 0 (Bjorn Helgaas)
- Check for platform_get_irq() failure consistently (Bjorn Helgaas)
- Replace zero-length array with flexible-array (Gustavo A. R. Silva)
- Unify pcie_find_root_port() and pci_find_pcie_root_port() (Yicong Yang)
- Quirk Intel C620 MROMs, which have non-BARs in BAR locations (Xiaochun
Lee)
- Fix pcie_pme_resume() and pcie_pme_remove() kernel-doc (Jay Fang)
- Rename _DSM constants to align with spec (Krzysztof Wilczyński)
* pci/misc:
PCI: Rename _DSM constants to align with spec
PCI/PME: Fix kernel-doc of pcie_pme_resume() and pcie_pme_remove()
x86/PCI: Mark Intel C620 MROMs as having non-compliant BARs
PCI: Unify pcie_find_root_port() and pci_find_pcie_root_port()
PCI: Replace zero-length array with flexible-array
PCI: Check for platform_get_irq() failure consistently
driver core: platform: Clarify that IRQ 0 is invalid
Don't disable MEM/IO decoding when a device have both non_compliant_bars
and mmio_always_on.
That would allow us quirk devices with junk in BARs but can't disable
their decoding.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Root Complex Integrated Endpoints (RCiEPs) do not have an upstream bridge,
so pci_configure_mps() previously ignored them, which may result in reduced
performance.
Instead, program the Max_Payload_Size of RCiEPs to the maximum supported
value (unless it is limited for the PCIE_BUS_PEER2PEER case). This also
affects the subsequent programming of Max_Read_Request_Size because Linux
programs MRRS based on the MPS value.
Fixes: 9dae3a9729 ("PCI: Move MPS configuration check to pci_configure_device()")
Link: https://lore.kernel.org/r/1585343775-4019-1-git-send-email-ashok.raj@intel.com
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
The PCI code has several paths where the struct pci_host_bridge is freed
directly. This is wrong because it contains a struct device which is
refcounted and should be freed using put_device(). This can result in
use-after-free errors. I think this problem has existed since 2012 with
commit 7b54366358 ("PCI: add generic device into pci_host_bridge
struct"). It generally hasn't mattered as most host bridge drivers are
still built-in and can't unbind.
The problem is a struct device should never be freed directly once
device_initialize() is called and a ref is held, but that doesn't happen
until pci_register_host_bridge(). There's then a window between allocating
the host bridge and pci_register_host_bridge() where kfree should be used.
This is fragile and requires callers to do the right thing. To fix this, we
need to split device_register() into device_initialize() and device_add()
calls, so that the host bridge struct is always freed by using a
put_device().
devm_pci_alloc_host_bridge() is using devm_kzalloc() to allocate struct
pci_host_bridge which will be freed directly. Instead, we can use a custom
devres action to call put_device().
Link: https://lore.kernel.org/r/20200513223859.11295-2-robh@kernel.org
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
If device_register() has an error, we should bail out of
pci_register_host_bridge() rather than continuing on.
Fixes: 37d6a0a6f4 ("PCI: Add pci_register_host_bridge() interface")
Link: https://lore.kernel.org/r/20200513223859.11295-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Previously we used pcie_find_root_port() to find a Root Port from a PCIe
device and pci_find_pcie_root_port() to find a Root Port from a
Conventional PCI device.
Unify the two functions and use pcie_find_root_port() to find a Root Port
from either a Conventional PCI device or a PCIe device. Then there is no
need to distinguish the type of the device.
Link: https://lore.kernel.org/r/1589019568-5216-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # thunderbolt
Error Disconnect Recover (EDR) is a feature that allows ACPI firmware to
notify OSPM that a device has been disconnected due to an error condition
(ACPI v6.3, sec 5.6.6). OSPM advertises its support for EDR on PCI devices
via _OSC (see [1], sec 4.5.1, table 4-4). The OSPM EDR notify handler
should invalidate software state associated with disconnected devices and
may attempt to recover them. OSPM communicates the status of recovery to
the firmware via _OST (sec 6.3.5.2).
For PCIe, firmware may use Downstream Port Containment (DPC) to support
EDR. Per [1], sec 4.5.1, table 4-6, even if firmware has retained control
of DPC, OSPM may read/write DPC control and status registers during the EDR
notification processing window, i.e., from the time it receives an EDR
notification until it clears the DPC Trigger Status.
Note that per [1], sec 4.5.1 and 4.5.2.4,
1. If the OS supports EDR, it should advertise that to firmware by
setting OSC_PCI_EDR_SUPPORT in _OSC Support.
2. If the OS sets OSC_PCI_EXPRESS_DPC_CONTROL in _OSC Control to request
control of the DPC capability, it must also set OSC_PCI_EDR_SUPPORT in
_OSC Support.
Add an EDR notify handler to attempt recovery.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
[bhelgaas: squash add/enable patches into one]
Link: https://lore.kernel.org/r/90f91fe6d25c13f9d2255d2ce97ca15be307e1bb.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Add pci_speed_string() to return a text description of the supplied bus or
link speed. The slot code previously used the private
pci_bus_speed_strings[] array for this purpose, but adding this interface
will enable us to consolidate similar code elsewhere.
Export pcie_link_speed[] and pci_speed_string() so they can be used by
modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the VFs,
but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and associated
VFs can be enabled independently (Kuppuswamy Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn Helgaas)
- Hide PRI and PASID state restoration functions used only inside the PCI
core (Bjorn Helgaas)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George Cherian)
- Unify ACS quirk implementations (Bjorn Helgaas)
* pci/virtualization:
PCI: Unify ACS quirk desired vs provided checking
PCI: Make ACS quirk implementations more uniform
PCI: Apply Cavium ACS quirk to ThunderX2 and ThunderX3
PCI/IOV: Serialize sysfs sriov_numvfs reads vs writes
PCI: Add DMA alias quirk for Intel VCA NTB
PCI: Fix Intel ACS quirk UPDCR register address
PCI/ATS: Make pci_restore_pri_state(), pci_restore_pasid_state() private
PCI/ATS: Remove unnecessary EXPORT_SYMBOL_GPL()
PCI/ATS: Remove unused PRI and PASID stubs
PCI/ATS: Consolidate ATS declarations in linux/pci-ats.h
PCI/ATS: Cache PRI PRG Response PASID Required bit
PCI/ATS: Cache PASID Capability offset
PCI/ATS: Cache PRI Capability offset
PCI/ATS: Disable PF/VF ATS service independently
PCI/ATS: Handle sharing of PF PASID Capability with all VFs
PCI/ATS: Handle sharing of PF PRI Capability with all VFs
PCI/ATS: Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI
iommu/vt-d: Select PCI_PRI for INTEL_IOMMU_SVM
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis Efremov)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control the
MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA devices
downstream (Subbaraya Sundeep)
* pci/resource:
PCI: Do not use bus number zero from EA capability
PCI: Avoid double hpmemsize MMIO window assignment
PCI: Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters
PCI: Add PCI_STD_NUM_BARS for the number of standard BARs
PCI: Fix missing bridge dma_ranges resource list cleanup
PCI: Protect pci_reassign_bridge_resources() against concurrent addition/removal
Remove <linux/pci.h> and <linux/msi.h> from being included directly as part
of the include/linux/of_pci.h, and remove superfluous declaration of struct
of_phandle_args.
Move users of include <linux/of_pci.h> to include <linux/pci.h> and
<linux/msi.h> directly rather than rely on both being included transitively
through <linux/of_pci.h>.
Link: https://lore.kernel.org/r/20190903113059.2901-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
As per PCIe r5.0, sec 7.8.5.2, fixed bus numbers of a bridge must be zero
when no function that uses EA is located behind it. Hence, if EA supplies
bus numbers of zero, assign bus numbers normally. A secondary bus can
never have a bus number of zero, so setting a bridge's Secondary Bus Number
to zero makes downstream devices unreachable.
[bhelgaas: retain bool return value so "zero is invalid" logic is local]
Fixes: 2dbce59011 ("PCI: Assign bus numbers present in EA capability for bridges")
Link: https://lore.kernel.org/r/1572850664-9861-1-git-send-email-sundeep.lkml@gmail.com
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.2+
In pci_call_probe(), we try to run driver probe functions on the node where
the device is attached. If we don't know which node the device is attached
to, the driver will likely run on the wrong node. This will still work,
but performance will not be as good as it could be.
On NUMA systems, warn if we don't know which node a PCI host bridge is
attached to. This is likely an indication that ACPI didn't supply a _PXM
method or the DT didn't supply a "numa-node-id" property.
[bhelgaas: commit log, check bus node]
Link: https://lore.kernel.org/r/1571467543-26125-1-git-send-email-linyunsheng@huawei.com
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit e80a91ad30 ("PCI: Add dma_ranges window list") added a
dma_ranges resource list, but failed to correctly free the list when
devm_pci_alloc_host_bridge() is used.
Only the iproc host bridge driver is using the dma_ranges list.
Fixes: e80a91ad30 ("PCI: Add dma_ranges window list")
Link: https://lore.kernel.org/r/20191008012325.25700-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
In some systems, the Device/Port Type in the PCI Express Capabilities
register incorrectly identifies upstream ports as downstream ports.
d0751b98df ("PCI: Add dev->has_secondary_link to track downstream PCIe
links") addressed this by adding pci_dev.has_secondary_link, which is set
for downstream ports. But this is confusing because pci_pcie_type()
sometimes gives the wrong answer, and it's not obvious that we should use
pci_dev.has_secondary_link instead.
Reduce the confusion by correcting the type of the port itself so that
pci_pcie_type() returns the actual type regardless of what the Device/Port
Type register claims it is. Update the users to call pci_pcie_type() and
pcie_downstream_port() accordingly, and remove pci_dev.has_secondary_link
completely.
Link: https://lore.kernel.org/linux-pci/20190703133953.GK128603@google.com/
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20190822085553.62697-2-mika.westerberg@linux.intel.com
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Move the ACPI-specific structs hpx_type0, hpx_type1, hpx_type2 and
hpx_type3 to drivers/pci/pci-acpi.c as they are not used anywhere else.
Then remove the struct hotplug_program_ops that has been shared between
drivers/pci/probe.c and drivers/pci/pci-acpi.c from drivers/pci/pci.h as it
is no longer needed.
The struct hotplug_program_ops was added by 87fcf12e84 ("PCI/ACPI: Remove
the need for 'struct hotplug_params'") and replaced previously used struct
hotplug_params enabling the support for the _HPX Type 3 Setting Record that
was added by f873c51a15 ("PCI/ACPI: Implement _HPX Type 3 Setting
Record").
The new struct allowed for the static functions such program_hpx_type0(),
program_hpx_type1(), etc., from the drivers/pci/probe.c to be called from
the function pci_acpi_program_hp_params() in the drivers/pci/pci-acpi.c.
Previously a programming of _HPX Type 0 was as follows:
drivers/pci/probe.c:
program_hpx_type0()
...
pci_configure_device()
hp_ops = {
.program_type0 = program_hpx_type0,
...
}
pci_acpi_program_hp_params(&hp_ops)
drivers/pci/pci-acpi.c:
pci_acpi_program_hp_params(&hp_ops)
acpi_run_hpx(hp_ops)
decode_type0_hpx_record()
hp_ops->program_type0 # program_hpx_type0() called via hp_ops
After the ACPI-specific functions, structs, enums, etc., have been moved to
drivers/pci/pci-acpi.c there is no need for the hotplug_program_ops as all
of the _HPX Type 0, 1, 2 and 3 are directly accessible.
Link: https://lore.kernel.org/r/20190827094951.10613-4-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move program_hpx_type0(), program_hpx_type1(), etc., and enums
hpx_type3_dev_type, hpx_type3_fn_type and hpx_type3_cfg_loc to
drivers/pci/pci-acpi.c as these functions and enums are ACPI-specific.
Move structs hpx_type0, hpx_type1, hpx_type2 and hpx_type3 to
drivers/pci/pci.h as these are shared between drivers/pci/pci-acpi.c and
drivers/pci/probe.c.
Link: https://lore.kernel.org/r/20190827094951.10613-3-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The names of the hpp_type0, hpp_type1 and hpp_type2 structs suggest that
they're related to _HPP, when in fact they're related to _HPX.
The struct hpp_type0 denotes an _HPX Type 0 setting record that supersedes
the _HPP setting record, and it has been used interchangeably for _HPP as
per the ACPI specification (see version 6.3, section 6.2.9.1) which states
that it should be applied to PCI, PCI-X and PCI Express devices, with
settings being ignored if they are not applicable.
Rename them to hpx_type0, hpx_type1 and hpx_type2 to reflect their relation
to _HPX rather than _HPP.
Link: https://lore.kernel.org/r/20190827094951.10613-2-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a generic helper to match any/all devices. Using this
introduce new wrappers {bus/driver/class}_find_next_device().
Cc: Elie Morisse <syniurge@gmail.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Nehal Shah <nehal-bakulchandra.shah@amd.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Shyam Sundar S K <shyam-sundar.s-k@amd.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # PCI
Link: https://lore.kernel.org/r/20190723221838.12024-7-suzuki.poulose@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix problem with caching VF config space size (Alex Williamson)
* pci/virtualization:
PCI/IOV: Assume SR-IOV VFs support extended config space.
Revert "PCI/IOV: Use VF0 cached config space size for other VFs"
The SR-IOV specification requires both PFs and VFs to implement a PCIe
capability. Generally this is sufficient to assume extended config space
is present, but we generally also perform additional tests to make sure the
extended config space is reachable and not simply an alias of standard
config space. For a VF to exist extended config space must be accessible
on the PF, therefore we can also assume it to be accessible on the VF.
This enables a micro performance optimization previously implemented in
commit 975bb8b4dc ("PCI/IOV: Use VF0 cached config space size for other
VFs") to speed up probing of VFs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Hao Zheng <yinhe@linux.alibaba.com>
Revert 975bb8b4dc ("PCI/IOV: Use VF0 cached config space size for other
VFs"), which attempted to cache the config space size from the first VF to
re-use for subsequent VFs.
The cached value was determined prior to discovering the PCIe capability on
the VF, which resulted in the first VF reporting the correct config space
size (4K), as it has a special case through pci_cfg_space_size(), while all
the other VFs only reported 256 bytes. As this was only a performance
optimization, we're better off without it.
Fixes: 975bb8b4dc ("PCI/IOV: Use VF0 cached config space size for other VFs")
Link: https://lore.kernel.org/r/156046663197.29869.3633634445109057665.stgit@gimli.home
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: KarimAllah Ahmed <karahmed@amazon.de>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Hao Zheng <yinhe@linux.alibaba.com>
There is an arbitrary difference between the prototypes of
bus_find_device() and class_find_device() preventing their callers
from passing the same pair of data and match() arguments to both of
them, which is the const qualifier used in the prototype of
class_find_device(). If that qualifier is also used in the
bus_find_device() prototype, it will be possible to pass the same
match() callback function to both bus_find_device() and
class_find_device(), which will allow some optimizations to be made in
order to avoid code duplication going forward. Also with that, constify
the "data" parameter as it is passed as a const to the match function.
For this reason, change the prototype of bus_find_device() to match
the prototype of class_find_device() and adjust its callers to use the
const qualifier in accordance with the new prototype of it.
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andreas Noever <andreas.noever@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Kershner <david.kershner@unisys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: David Airlie <airlied@linux.ie>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Harald Freudenberger <freude@linux.ibm.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michael Jamet <michael.jamet@intel.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Oberparleiter <oberpar@linux.ibm.com>
Cc: Sebastian Ott <sebott@linux.ibm.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Yehezkel Bernat <YehezkelShB@gmail.com>
Cc: rafael@kernel.org
Acked-by: Corey Minyard <minyard@acm.org>
Acked-by: David Kershner <david.kershner@unisys.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for the I2C parts
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCIe r5.0, sec 7.5.3.18, defines a new 32.0 GT/s bit in the Supported Link
Speeds Vector of Link Capabilities 2. Decode this new speed. This does
not affect the speed of the link, which should be negotiated automatically
by the hardware; it only adds decoding when showing the speed to the user.
Previously, reading the speed of a link operating at this speed showed
"Unknown speed" instead of "32.0 GT/s".
Link: https://lore.kernel.org/lkml/92365e3caf0fc559f9ab14bcd053bfc92d4f661c.1559664969.git.gustavo.pimentel@synopsys.com
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/printk:
PCI: Replace dev_printk(KERN_DEBUG) with dev_info(), etc
PCI: Replace printk(KERN_INFO) with pr_info(), etc
PCI: Use dev_printk() when possible
- Fix RPA and RPA DLPAR refcount issues (Tyrel Datwyler)
- Stop exporting pci_get_hp_params() (Alexandru Gagniuc)
- Simplify _HPP, _HPX parsing (Alexandru Gagniuc)
- Add support for _HPX Type 3 settings (Alexandru Gagniuc)
- Tell firmware we support _HPX Type 3 via _OSC (Alexandru Gagniuc)
* pci/hotplug:
PCI/ACPI: Advertise _HPX Type 3 support via _OSC
PCI/ACPI: Implement _HPX Type 3 Setting Record
PCI/ACPI: Remove the need for 'struct hotplug_params'
PCI/ACPI: Do not export pci_get_hp_params()
PCI: rpaphp: Get/put device node reference during slot alloc/dealloc
PCI: rpadlpar: Fix leaked device_node references in add/remove paths
Replace dev_printk(KERN_DEBUG) with dev_info(), etc to be more consistent
with other logging and avoid checkpatch warnings.
The KERN_DEBUG messages could be converted to dev_dbg(), but that depends
on CONFIG_DYNAMIC_DEBUG and DEBUG, and we want most of these messages to
*always* be in the dmesg log.
Link: https://lore.kernel.org/lkml/1555733240-19875-1-git-send-email-mohankumar718@gmail.com
Signed-off-by: Mohan Kumar <mohankumar718@gmail.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a dma_ranges field in PCI host bridge structure to hold resource
entries list of memory regions in sorted order representing memory ranges
that can be accessed through DMA transactions.
Based-on-a-patch-by: Oza Pawandeep <oza.oza@broadcom.com>
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Oza Pawandeep <poza@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The _HPX Type 3 Setting Record is intended to be more generic and allow
configuration of settings not possible with Type 2 records. For example,
firmware could ensure that the completion timeout value is set accordingly
throughout the PCI tree.
Implement support for _HPX Type 3 Setting Records, which were added in the
ACPI 6.3 spec.
Link: https://lore.kernel.org/lkml/20190208162414.3996-4-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We used to first parse all the _HPP and _HPX tables before using the
information to program registers of PCIe devices. Up through HPX Type 2,
there was only one structure of each type, so we could cheat and store it
on the stack.
With HPX Type 3 we get an arbitrary number of entries, so the above model
doesn't scale that well. Instead of parsing all tables at once, parse and
program each entry separately. For _HPP and _HPX Types 0 through 2, this
is functionally equivalent. The change enables the upcoming _HPX Type 3 to
integrate more easily.
Link: https://lore.kernel.org/lkml/20190208162414.3996-3-mr.nuke.me@gmail.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[bhelgaas: fix build errors]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The "Enhanced Allocation (EA) for Memory and I/O Resources" ECN, approved
23 October 2014, sec 6.9.1.2, specifies a second DW in the capability for
type 1 (bridge) functions to describe fixed secondary and subordinate bus
numbers. This ECN was included in the PCIe r4.0 spec, but sec 6.9.1.2 was
omitted, presumably by mistake.
Read fixed bus numbers from the EA capability for bridges.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
[bhelgaas: add pci_ea_fixed_busnrs() return value]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Two functions allocate a host bridge: devm_pci_alloc_host_bridge() and
pci_alloc_host_bridge(). At the moment, only the unmanaged one initializes
the PCIe feature bits, which prevents from using features such as hotplug
or AER on some systems, when booting with device tree. Make the
initialization code common.
Fixes: 02bfeb4842 ("PCI/portdrv: Simplify PCIe feature permission checking")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.17+
If a multi-function device's bandwidth is already limited when it is
enumerated, a message is logged only for function 0. By contrast, when
downtraining occurs after enumeration, a message is logged for all
functions. That's because the former uses pcie_report_downtraining(),
whereas the latter uses __pcie_print_link_status() (which doesn't filter
functions != 0). I am seeing this happen on a MacBookPro9,1 with a GPU
(function 0) and an integrated HDA controller (function 1).
Avoid this incongruence by calling pcie_report_downtraining() in both
cases.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alexandru Gagniuc <alex.gagniuc@dellteam.com>
- Probe bridge window attributes only once at enumeration-time to fix
device accesses during rescan (Bjorn Helgaas)
- Return BAR size (not "size -1 ") from pci_size() to simplify code (Du
Changbin)
- Use config header type (not class code) identify bridges more reliably
(Honghui Zhang)
- Work around Intel Denverton incorrect Trace Hub BAR size reporting
(Alexander Shishkin)
* pci/enumeration:
x86/PCI: Fixup RTIT_BAR of Intel Denverton Trace Hub
PCI: Rely on config space header type, not class code
PCI: Make pci_size() return real BAR size
PCI: Probe bridge window attributes once at enumeration-time
- Use Latency Tolerance Reporting if already enabled by platform (Bjorn
Helgaas)
- Save/restore LTR info for suspend/resume (Bjorn Helgaas)
* pci/aspm:
PCI/ASPM: Save LTR Capability for suspend/resume
PCI/ASPM: Use LTR if already enabled by platform
RussianNeuroMancer reported that the Intel 7265 wifi on a Dell Venue 11 Pro
7140 table stopped working after wakeup from suspend and bisected the
problem to 9ab105deb6 ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't
have LTR"). David Ward reported the same problem on a Dell Latitude 7350.
After af8bb9f898 ("PCI/ACPI: Request LTR control from platform before
using it"), we don't enable LTR unless the platform has granted LTR control
to us. In addition, we don't notice if the platform had already enabled
LTR itself.
After 9ab105deb6 ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't have
LTR"), we avoid using LTR if we don't think the path to the device has LTR
enabled.
The combination means that if the platform itself enables LTR but declines
to give the OS control over LTR, we unnecessarily avoided using ASPM L1.2.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201469
Fixes: 9ab105deb6 ("PCI/ASPM: Disable ASPM L1.2 Substate if we don't have LTR")
Fixes: af8bb9f898 ("PCI/ACPI: Request LTR control from platform before using it")
Reported-by: RussianNeuroMancer <russianneuromancer@ya.ru>
Reported-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.18+
As per Figure 6-3 in PCIe r4.0, sec 6.2.6, ERR_ messages will be forwarded
from the secondary interface to the primary interface, if the SERR# Enable
bit in the Bridge Control register is set.
It seems clear that an ACPI hotplug parameter method (_HPP or _HPX) that
tells us to "enable SERR in the command register" (ACPI v6.2, sec 6.2.8,
6.2.9.1) refers to PCI_COMMAND_SERR, which enables reporting of errors by
the function itself.
For bridges, we also interpreted that to mean we should enable
PCI_BRIDGE_CTL_SERR, which enables *forwarding* of errors by the bridge.
But we didn't enable PCI_BRIDGE_CTL_SERR anywhere else, which means we
never enabled it for non-ACPI systems or ACPI systems that didn't supply
hotplug parameters.
That means errors reported below bridges were often never forwarded up to a
Root Port where they could be signaled via AER.
Enable PCI_BRIDGE_CTL_SERR for all bridges so we can get better error
reporting for downstream devices.
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI configuration space header type tells us whether the device is a
bridge, a CardBus bridge, or a normal device, and defines the layout of the
rest of the header (PCI r3.0 sec 6.1, PCIe r4.0 sec 7.5.1.1.9).
When we rely on the header format, e.g., when we're dealing with bridge
windows, we should check the header type, not the class code. The class
code is loosely related to the header type, but is often incorrect and the
spec doesn't actually require it to be related to the header format.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
[bhelgaas: changelog, keep the PCI_CLASS_BRIDGE_HOST check]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently, the pci_size() function actually returns 'size-1'. Make it
return real size to avoid confusion.
Signed-off-by: Du Changbin <changbin.du@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_bridge_check_ranges() determines whether a bridge supports the optional
I/O and prefetchable memory windows and sets the flag bits in the bridge
resources. This *could* be done once during enumeration except that the
resource allocation code completely clears the flag bits, e.g., in the
pci_assign_unassigned_bridge_resources() path.
The problem with pci_bridge_check_ranges() in the resource allocation path
is that we may allocate resources after devices have been claimed by
drivers, and pci_bridge_check_ranges() *changes* the window registers to
determine whether they're writable. This may break concurrent accesses to
devices behind the bridge.
Add a new pci_read_bridge_windows() to determine whether a bridge supports
the optional windows, call it once during enumeration, remember the
results, and change pci_bridge_check_ranges() so it doesn't touch the
bridge windows but sets the flag bits based on those remembered results.
Link: https://lore.kernel.org/linux-pci/1506151482-113560-1-git-send-email-wangzhou1@hisilicon.com
Link: https://lists.gnu.org/archive/html/qemu-devel/2018-12/msg02082.html
Reported-by: Yandong Xu <xuyandong2@huawei.com>
Tested-by: Yandong Xu <xuyandong2@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Ofer Hayut <ofer@lightbitslabs.com>
Cc: Roy Shterman <roys@lightbitslabs.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
A malicious PCI device may use DMA to attack the system. An external
Thunderbolt port is a convenient point to attach such a device. The OS
may use IOMMU to defend against DMA attacks.
Some BIOSes mark these externally facing root ports with this
ACPI _DSD [1]:
Name (_DSD, Package () {
ToUUID ("efcc06cc-73ac-4bc3-bff0-76143807c389"),
Package () {
Package () {"ExternalFacingPort", 1},
Package () {"UID", 0 }
}
})
If we find such a root port, mark it and all its children as untrusted.
The rest of the OS may use this information to enable DMA protection
against malicious devices. For instance the device may be put behind an
IOMMU to keep it from accessing memory outside of what the driver has
allocated for it.
While at it, add a comment on top of prp_guids array explaining the
possible caveat resulting when these GUIDs are treated equivalent.
[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/pci/dsd-for-pcie-root-ports#identifying-externally-exposed-pcie-root-ports
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
* pci/virtualization:
PCI/IOV: Remove unnecessary include of <linux/pci-ats.h>
PCI/IOV: Use VF0 cached config space size for other VFs
Cache the config space size from VF0 and use it for all other VFs instead
of reading it from the config space of each VF. We assume that it will be
the same across all associated VFs.
This is an optimization when enabling SR-IOV on a device with many VFs.
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
[bhelgaas: use CONFIG_PCI_IOV (not CONFIG_PCI_ATS)]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The few callers can just use dma_set_max_seg_size ()directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The two callers can just use dma_set_seg_boundary() directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The spec has timing requirements when waiting for a link to become active
after a conventional reset. Implement those hard delays when waiting for
an active link so pciehp and dpc drivers don't need to duplicate this.
For devices that don't support data link layer active reporting, wait the
fixed time recommended by the PCIe spec.
Signed-off-by: Keith Busch <keith.busch@intel.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Switch to bitmap_zalloc() to show clearly what we are allocating. Besides
that it returns pointer of bitmap type ("unsigned long *") instead of the
opaque "void *".
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Set the eetlp_prefix_path on PCIE_EXP_TYPE_RC_END devices to allow PASID
to be enabled on them. This fixes IOMMUv2 initialization on AMD Carrizo
APUs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201079
Fixes: 7ce3f912ae ("PCI: Enable PASID only if entire path supports End-End TLP prefixes")
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
- To avoid bus errors, enable PASID only if entire path supports End-End
TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD Controller
(Bjorn Helgaas)
* pci/virtualization:
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: Rename pci_try_reset_bus() to pci_reset_bus()
PCI: Deprecate pci_reset_bus() and pci_reset_slot() functions
PCI: Unify try slot and bus reset API
PCI: Hide pci_reset_bridge_secondary_bus() from drivers
IB/hfi1: Use pci_try_reset_bus() for initiating PCI Secondary Bus Reset
PCI: Handle error return from pci_reset_bridge_secondary_bus()
PCI/IOV: Tidy pci_sriov_set_totalvfs()
PCI: Enable PASID only if entire path supports End-End TLP prefixes
# Conflicts:
# drivers/pci/hotplug/pciehp_hpc.c
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
* pci/resource:
PCI: Make pci_get_rom_size() static
PCI: Add check code for last image indicator not set
PCI: Avoid accessing memory outside the ROM BAR
PCI: Make early dump functionality generic
PCI: Cleanup PCI_REBAR_CTRL_BAR_SHIFT handling
PCI: Restore resized BAR state on resume
PCI: Clean up resource allocation in devm_of_pci_get_host_bridge_resources()
# Conflicts:
# Documentation/admin-guide/kernel-parameters.txt
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a device
below it (Myron Stowe)
* pci/enumeration:
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Check for PCIe Link downtraining
PCI: Workaround IDT switch ACS Source Validation erratum
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
* pci/aspm:
PCI: Remove unnecessary include of <linux/pci-aspm.h>
iwlwifi: Remove unnecessary include of <linux/pci-aspm.h>
ath9k: Remove unnecessary include of <linux/pci-aspm.h>
igb: Remove unnecessary include of <linux/pci-aspm.h>
PCI/ASPM: Convert to use sysfs_match_string() helper
