The regulator setup was likely copied from other SoCs by mistake. Just
like SM6125 the DSI PHY on this platform is not getting power from a
regulator but from the MX power domain.
Fixes: 572e9fd6d1 ("drm/msm/dsi: Add phy configuration for QCM2290")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/544536/
Link: https://lore.kernel.org/r/20230627-sm6125-dpu-v2-1-03e430a2078c@somainline.org
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Currently, slice_count is being used to calculate word count and
pkt_per_line. Instead, these values should be calculated using slice per
packet, which is not the same as slice_count.
Slice count represents the number of slices per interface, and its value
will not always match that of slice per packet. For example, it is possible
to have cases where there are multiple slices per interface but the panel
specifies only one slice per packet.
Thus, use the default value of one slice per packet and remove slice_count
from the aforementioned calculations.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Fixes: bc6b6ff813 ("drm/msm/dsi: Use DSC slice(s) packet size to compute word count")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541965/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-5-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, when compression is enabled, hdisplay is reduced via integer
division. This causes issues for modes where the original hdisplay is
not a multiple of 3.
To fix this, use DIV_ROUND_UP to divide hdisplay.
Suggested-by: Marijn Suijten <marijn.suijten@somainline.org>
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541970/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-1-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, hdisplay is being divided by 3 for DSC. However, this
calculation only works for cases where BPP = 8.
Update hdisplay calculation to be bytes_per_line / 3, so that it
accounts for cases where BPP != 8.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539271/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-9-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Use new DRM DSC helpers to setup DSI DSC configuration. The
initial_scale_value needs to be adjusted according to the standard, but
this is a separate change.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/539276/
Link: https://lore.kernel.org/r/20230329-rfc-msm-dsc-helper-v14-4-bafc7be95691@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
MSM8226 uses a modified PLL lock sequence compared to MSM8974, which is
based on the function dsi_pll_enable_seq_m in the msm-3.10 kernel.
Worth noting that the msm-3.10 downstream kernel also will try other
sequences in case this one doesn't work, but during testing it has shown
that the _m sequence succeeds first time also:
.pll_enable_seqs[0] = dsi_pll_enable_seq_m,
.pll_enable_seqs[1] = dsi_pll_enable_seq_m,
.pll_enable_seqs[2] = dsi_pll_enable_seq_d,
.pll_enable_seqs[3] = dsi_pll_enable_seq_d,
.pll_enable_seqs[4] = dsi_pll_enable_seq_f1,
.pll_enable_seqs[5] = dsi_pll_enable_seq_c,
.pll_enable_seqs[6] = dsi_pll_enable_seq_e,
We may need to expand this in the future.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/540618/
Link: https://lore.kernel.org/r/20230308-msm8226-mdp-v3-6-b6284145d67a@z3ntu.xyz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Add the config for the v1.0.2 DSI found on MSM8226. We can reuse
existing bits from other revisions that are identical for v1.0.2.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Patchwork: https://patchwork.freedesktop.org/patch/540616/
Link: https://lore.kernel.org/r/20230308-msm8226-mdp-v3-5-b6284145d67a@z3ntu.xyz
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In dsi_calc_clk_rate_v2() there is no need to call dsi_get_pclk_rate().
This function has just been called (from dsi_calc_pclk()) and its
result is stored at msm_host->pixel_clk_rate. Use this variable
directly.
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/538272/
Link: https://lore.kernel.org/r/20230520200103.4019607-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
If the dispcc uses CLK_OPS_PARENT_ENABLE (e.g. on QCM2290), CCF can try
enabling VCO before the rate has been programmed. This can cause clock
lockups and/or other boot issues. Program the VCO to the minimal PLL
rate if the read rate is 0 Hz.
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reported-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Fixes: f079f6d999 ("drm/msm/dsi: Add PHY/PLL for 8x96")
Patchwork: https://patchwork.freedesktop.org/patch/534813/
Link: https://lore.kernel.org/r/20230501011257.3460103-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In commit 7d8e9a9050 ("drm/msm/dsi: move DSI host powerup to modeset
time") the error handling with regards to dsi_mgr_bridge_power_on()
got a bit worse. Specifically if we failed to power the bridge on then
nothing would really notice. The modeset function couldn't return an
error and thus we'd blindly go forward and try to do the pre-enable.
In commit ec7981e6c6 ("drm/msm/dsi: don't powerup at modeset time
for parade-ps8640") we added a special case to move the powerup back
to pre-enable time for ps8640. When we did that, we didn't try to
recover the old/better error handling just for ps8640.
In the patch ("drm/msm/dsi: Stop unconditionally powering up DSI hosts
at modeset") we've now moved the powering up back to exclusively being
during pre-enable. That means we can add the better error handling
back in, so let's do it. To do so we'll add a new function
dsi_mgr_bridge_power_off() that's matches how errors were handled
prior to commit 7d8e9a9050 ("drm/msm/dsi: move DSI host powerup to
modeset time").
NOTE: Now that we have dsi_mgr_bridge_power_off(), it feels as if we
should be calling it in dsi_mgr_bridge_post_disable(). That would make
some sense, but doing so would change the current behavior and thus
should be a separate patch. Specifically:
* dsi_mgr_bridge_post_disable() always calls dsi_mgr_phy_disable()
even in the slave-DSI case of bonded DSI. We'd need to add special
handling for this if it's truly needed.
* dsi_mgr_bridge_post_disable() calls msm_dsi_phy_pll_save_state()
midway through the poweroff.
* dsi_mgr_bridge_post_disable() has a different order of some of the
poweroffs / IRQ disables.
For now we'll leave dsi_mgr_bridge_post_disable() alone.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/521059/
Link: https://lore.kernel.org/r/20230131141756.RFT.v2.3.I3c87b53c4ab61a7d5e05f601a4eb44c7e3809a01@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In commit 7d8e9a9050 ("drm/msm/dsi: move DSI host powerup to modeset
time"), we moved powering up DSI hosts to modeset time. This wasn't
because it was an elegant design, but there were no better options.
That commit actually ended up breaking ps8640, and thus was born
commit ec7981e6c6 ("drm/msm/dsi: don't powerup at modeset time for
parade-ps8640") as a temporary hack to un-break ps8640 by moving it to
the old way of doing things. It turns out that ps8640 _really_ doesn't
like its pre_enable() function to be called after
dsi_mgr_bridge_power_on(). Specifically (from experimentation, not
because I have any inside knowledge), it looks like the assertion of
"RST#" in the ps8640 runtime resume handler seems like it's not
allowed to happen after dsi_mgr_bridge_power_on()
Recently, Dave Stevenson's series landed allowing bridges some control
over pre_enable ordering. The meaty commit for our purposes is
commit 4fb912e5e1 ("drm/bridge: Introduce pre_enable_prev_first to
alter bridge init order"). As documented by that series, if a bridge
doesn't set "pre_enable_prev_first" then we should use the old ordering.
Now that we have the commit ("drm/bridge: tc358762: Set
pre_enable_prev_first") we can go back to the old ordering, which also
allows us to remove the ps8640 special case.
One last note is that even without reverting commit 7d8e9a9050
("drm/msm/dsi: move DSI host powerup to modeset time"), if you _just_
revert the ps8640 special case and try it out then it doesn't seem to
fail anymore. I spent time bisecting / debugging this and it turns out
to be mostly luck, so we still want this patch to make sure it's
solid. Specifically the reason it sorta works these days is because
we implemented wait_hpd_asserted() in ps8640 now, plus the magic of
"pm_runtime" autosuspend. The fact that we have wait_hpd_asserted()
implemented means that we actually power the bridge chip up just a wee
bit earlier and then the bridge happens to stay on because of
autosuspend and thus ends up powered before dsi_mgr_bridge_power_on().
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/521058/
Link: https://lore.kernel.org/r/20230131141756.RFT.v2.2.I4cfeab9d0e07e98ead23dd0736ab4461e6c69002@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Now that the only user is handled by common code, remove the option to
specify custom handlers through match data.
This is effectively a revert of commit:
5ae15e76271 ("drm/msm/dsi: Allow to specify dsi config as pdata")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527662/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-7-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Now that the logic can handle multiple sets of registers, move
the QCM2290 to the common logic and mark it deprecated. This allows us
to remove a couple of structs, saving some memory.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527656/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-6-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The configs are identical, other than the number of *maximum* DSI
hosts allowed. This isn't an issue, unless somebody deliberately
tries to access the inexistent host by adding a dt node for it.
Remove the SC7180 struct and point the hw revision match to the
SDM845's one. On a note, this could have been done back when
7180 support was introduced.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527654/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-5-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, we allow for MAX_DSI entries in io_start to facilitate for
MAX_DSI number of DSI hosts at different addresses. The configuration
is matched against the DSI CTRL hardware revision read back from the
component. We need a way to resolve situations where multiple SoCs
with different register maps may use the same version of DSI CTRL. In
preparation to do so, make msm_dsi_config a 2d array where each entry
represents a set of configurations adequate for a given SoC.
This is totally fine to do, as the only differentiating factors
between same-version-different-SoCs configurations are the number of
DSI hosts (1 or 2, at least as of today) and the set of base registers.
The regulator setup is the same, because the DSI hardware is the same,
regardless of the SoC it was implemented in.
In addition to that, update the matching logic such that it will loop
over VARIANTS_MAX variants, making sure they are all taken into account.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527652/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-3-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In preparation for supporting multiple sets of possible base registers,
remove the num_dsi variable. We're comparing the io_start array contents
with the reg value from the DTS, so it will either match one of the
expected values or don't match against a zero (which we get from partial
array initialization).
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527658/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-2-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
It was left unnoticed during the review that even if there is no OPP
table in device tree, one will be created by a call to the function
devm_pm_opp_set_clkname(). This leads to dsi_mgr_bridge_mode_valid()
rejecting all modes if DT contains no OPP table for the DSI host.
Rework dsi_mgr_bridge_mode_valid() to handle this case by actually
checking that the table is populated with frequency entries before
returning an error.
Fixes: 8328041b8c ("drm/msm/dsi: implement opp table based check for dsi_mgr_bridge_mode_valid()")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520076/
Link: https://lore.kernel.org/r/20230124203600.3488766-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU, DSI, MDSS:
- Support for SM8350, SM8450 SM8550 and SC8280XP platform
Core:
- Added bindings for SM8150 (driver support already present)
DPU:
- Partial support for DSC on SM8150 and SM8250
- Fixed color transformation matrix being lost on suspend/resume
DP:
- Support for DP on SDM845 and SC8280XP platforms
- HPD fixes
- Support for limiting DP link rate via DT property, this enables
support for HBR3 rates.
DSI:
- Validate display modes according to the DSI OPP table
- DSI PHY support for the SM6375 platform
- Fixed byte intf clock selection for 14nm PHYs
MDP5:
- Schema conversion to YAML
Misc fixes as usual
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
v2.5.0 support was originally added for SC7280, but this hw is also
present on SM8350, which has one more DSI host. Bump up the dsi count
and fill in the register of the secondary host to allow it to probe.
This should not have any adverse effects on SC7280, as the secondary
CTRL will only be touched if it's defined, anyway.
Fixes: 65c391b319 ("drm/msm/dsi: Add DSI support for SC7280")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519513/
Link: https://lore.kernel.org/r/20230120210101.2146852-1-konrad.dybcio@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to the vendor kernel, byte intf clock rate should be a half of
the byte clock only when DSI PHY version is above 2.0 (in other words,
10nm PHYs and later) and only if PHY is used in D-PHY mode. Currently
MSM DSI code handles only the second part of the clause (C-PHY vs
D-PHY), skipping DSI PHY version check, which causes issues on some of
14nm DSI PHY platforms (e.g. qcm2290).
Move divisor selection to DSI PHY code, pass selected divisor through
shared timings and set byte intf clock rate accordingly.
Cc: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Konrad Dybcio <konrad.dybcio@linaro.org> # SM6115P J606F
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/519006/
Link: https://lore.kernel.org/r/20230118130027.2345719-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently there is no protection against a user trying to set
an unsupported mode on DSI. Implement a check based on the opp
table whether the byte clock for the mode can be supported by
validating whether an opp table entry exists.
For devices which have not added opp table support yet, skip
this check otherwise it will break bootup on those devices.
changes in v3:
- make the comment shorter
- handle all errors except ENODEV
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/15
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518008/
Link: https://lore.kernel.org/r/20230112001600.12791-2-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Re-arrange the dsi_calc_pclk method to two helpers, one to
compute the DSI byte clk and the other to compute the pclk.
This makes the separation of the two clean and also allows
clients to compute and use the dsi byte clk separately.
changes in v2:
- move the assignments to definition lines
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518005/
Link: https://lore.kernel.org/r/20230112001600.12791-1-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to downstream /and the comment copied from it/ this comparison
should be the other way around. In other words, when the panel driver
requests to use more slices per packet than what could be sent over this
interface, it is bumped down to only use a single slice per packet (and
strangely not the number of slices that could fit on the interface).
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515686/
Link: https://lore.kernel.org/r/20221221231943.1961117-4-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to downstream the value to use for WORD_COUNT is
bytes_per_pkt, which denotes the number of bytes in a packet based on
how many slices have been configured by the panel driver times the
width of a slice times the number of bytes per pixel.
The DSC panels seen thus far use one byte per pixel, only one slice
per packet, and a slice width of half the panel width leading to the
desired bytes_per_pkt+1 value to be equal to hdisplay/2+1. This however
isn't the case anymore for panels that configure two slices per packet,
where the value should now be hdisplay+1.
Note that the aforementioned panel (on a Sony Xperia XZ3, sdm845) with
slice_count=1 has also been tested to successfully accept slice_count=2,
which would have shown corrupted output previously.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515694/
Link: https://lore.kernel.org/r/20221221231943.1961117-3-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
In preparation to adding the sm8350 and sm8450 PHYs support, rearrange
register values calculations in dsi_7nm_phy_enable(). This change bears
no functional changes itself, it is merely a preparation for the next
patch.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/514232/
Link: https://lore.kernel.org/r/20221207012231.112059-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The bpg_offset array contains negative BPG offsets which fill the full 8
bits of a char thanks to two's complement: this however results in those
bits bleeding into the next field when the value is packed into DSC PPS
by the drm_dsc_helper function, which only expects range_bpg_offset to
contain 6-bit wide values. As a consequence random slices appear
corrupted on-screen (tested on a Sony Tama Akatsuki device with sdm845).
Use AND operators to limit these two's complement values to 6 bits,
similar to the AMD and i915 drivers.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508941/
Link: https://lore.kernel.org/r/20221026182824.876933-11-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
drm_dsc_config's bits_per_pixel field holds a fractional value with 4
bits, which all panel drivers should adhere to for
drm_dsc_pps_payload_pack() to generate a valid payload. All code in the
DSI driver here seems to assume that this field doesn't contain any
fractional bits, hence resulting in the wrong values being computed.
Since none of the calculations leave any room for fractional bits or
seem to indicate any possible area of support, disallow such values
altogether. calculate_rc_params() in intel_vdsc.c performs an identical
bitshift to get at this integer value.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508938/
Link: https://lore.kernel.org/r/20221026182824.876933-8-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
As per the FIXME this code is entirely duplicate with what is already
provided inside drm_dsc_compute_rc_parameters(), supposedly because that
function was yielding "incorrect" results while in reality the panel
driver(s?) used for testing were providing incorrect parameters.
For example, this code from downstream assumed dsc->bits_per_pixel to
contain an integer value, whereas the upstream drm_dsc_config struct
stores it with 4 fractional bits. drm_dsc_compute_rc_parameters()
already accounts for this feat while the panel driver used for testing
[1] wasn't, hence making drm_dsc_compute_rc_parameters() seem like it
was returning an incorrect result.
Other users of dsc->bits_per_pixel inside dsi_populate_dsc_params() also
treat it in the same erroneous way, and will be addressed in a separate
patch.
In the end, using drm_dsc_compute_rc_parameters() spares both a lot of
duplicate code and erratic behaviour.
[1]: https://git.linaro.org/people/vinod.koul/kernel.git/commit/?h=topic/pixel3_5.18-rc1&id=1d7d98ad564f1ec69e7525e07418918d90f247a1
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508939/
Link: https://lore.kernel.org/r/20221026182824.876933-7-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This field is currently unread but will come into effect when duplicated
code below is migrated to call drm_dsc_compute_rc_parameters(), which
uses the bpc-dependent value of the local variable mux_words_size in
much the same way.
The hardcoded constant seems to be a remnant from the `/* bpc 8 */`
comment right above, indicating that this group of field assignments is
applicable to bpc = 8 exclusively and should probably bail out on
different bpc values, until constants for other bpc values are added (or
the current ones are confirmed to be correct across multiple bpc's).
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508943/
Link: https://lore.kernel.org/r/20221026182824.876933-6-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
dsi_populate_dsc_params() is called prior to dsi_update_dsc_timing() and
already computes a value for slice_chunk_size, whose value doesn't need
to be recomputed and re-set here.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508934/
Link: https://lore.kernel.org/r/20221026182824.876933-5-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This exact same math is used to compute bytes_in_slice above in
dsi_update_dsc_timing(), also used to fill slice_chunk_size.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508935/
Link: https://lore.kernel.org/r/20221026182824.876933-4-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Multiplying a value by 2 and adding 1 to it always results in a value
that is uneven, and that 1 gets truncated immediately when performing
integer division by 2 again. There is no "rounding" possible here.
After that target_bpp_x16 is used to store a multiplication of
bits_per_pixel by 16 which is only ever read to immediately be divided
by 16 again, and is elided in much the same way.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508932/
Link: https://lore.kernel.org/r/20221026182824.876933-2-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The QCM2290 SoC a the 14nm (V2.0) single DSI phy. The platform is not
fully compatible with the standard 14nm PHY, so it requires a separate
compatible and config entry.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
[DB: rebased and updated commit msg]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/504578/
Link: https://lore.kernel.org/r/20220924121900.222711-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Drop the overly defensive modeset sanity checks of function parameters
which have already been checked or used by the callers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/502678/
Link: https://lore.kernel.org/r/20220913085320.8577-11-johan+linaro@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
