From now on only accepting complete software nodes.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old device property API is going to be removed and
replaced with the newer software node API. This prepares MFD
subsystem for the transition.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
By default the PMIC DA9063 2-wire interface is SMBus compliant. This
means the PMIC will automatically reset the interface when the clock
signal ceases for more than the SMBus timeout of 35 ms.
If the I2C driver / device is not capable of creating atomic I2C
transactions, a context change can cause a ceasing of the clock signal.
This can happen if for example a real-time thread is scheduled. Then
the DA9063 in SMBus mode will reset the 2-wire interface. Subsequently
a write message could end up in the wrong register. This could cause
unpredictable system behavior.
The DA9063 PMIC also supports an I2C compliant mode for the 2-wire
interface. This mode does not reset the interface when the clock
signal ceases. Thus the problem depicted above does not occur.
This patch tests for the bus functionality "I2C_FUNC_I2C". It can
reasonably be assumed that the bus cannot obey SMBus timings if
this functionality is set. SMBus commands most probably are emulated
in this case which is prone to the latency issue described above.
This patch enables the I2C bus mode if I2C_FUNC_I2C is set or
otherwise keeps the default SMBus mode.
Signed-off-by: Hubert Streidl <hubert.streidl@de.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch adds access tables to the MAX 10 BMC regmap. This prevents
the host from accessing the unwanted I/O space. It also filters out the
invalid outputs when reading the regmap debugfs interface.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The version register is the only one in the legacy I/O space to be
accessed, so it is not necessary to define the legacy base & version
register offset. A direct definition of the legacy version register
address would be fine.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fixes the max register address of MAX 10 BMC. The range
0x20000000 ~ 0x200000fc are for control registers of the QSPI flash
controller, which are not accessible to host.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ST-Ericsson U300 platform has been removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This define appears incorrect, but it is completely unused so it can be
removed.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix the following coccicheck warning:
./include/linux/mfd/db8500-prcmu.h:723:8-9: WARNING: return of 0/1 in
function 'db8500_prcmu_is_ac_wake_requested' with return type bool.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
-----BEGIN PGP SIGNATURE-----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=7O9a
-----END PGP SIGNATURE-----
mergetag object a908a71669
type commit
tag ib-mfd-extcon-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1616067995 +0000
Immutable branch between MFD and Extcon due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=3CZN
-----END PGP SIGNATURE-----
mergetag object eac013a0b7
type commit
tag ib-mfd-input-v5.13-1
tagger Lee Jones <lee.jones@linaro.org> 1615374673 +0000
Immutable branch between MFD and Input due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=NF6J
-----END PGP SIGNATURE-----
mergetag object aa47ad3f85
type commit
tag ib-mfd-platform-x86-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1615373744 +0000
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=340a
-----END PGP SIGNATURE-----
mergetag object ee0975c308
type commit
tag ib-mfd-power-v5.13
tagger Lee Jones <lee.jones@linaro.org> 1616489771 +0000
Immutable branch between MFD and Power due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=+5eM
-----END PGP SIGNATURE-----
mergetag object edbda8f787
type commit
tag ib-mfd-pwm-rtc-v5.13-1
tagger Lee Jones <lee.jones@linaro.org> 1615374433 +0000
Immutable branch between MFD, PWM and RTC due for the v5.13 merge window
-----BEGIN PGP SIGNATURE-----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=DySP
-----END PGP SIGNATURE-----
Merge tags 'ib-mfd-clk-gpio-regulator-rtc-v5.13', 'ib-mfd-extcon-v5.13', 'ib-mfd-input-v5.13-1', 'ib-mfd-platform-x86-v5.13', 'ib-mfd-power-v5.13', 'ib-mfd-pwm-rtc-v5.13-1' and 'ib-regulator-list-ramp-helpers-v5.13' into ibs-for-mfd-merged
Immutable branch between MFD, Clock, GPIO, Regulator and RTC due for the v5.13 merge window
Immutable branch between MFD and Extcon due for the v5.13 merge window
Immutable branch between MFD and Input due for the v5.13 merge window
Immutable branch between MFD and Platform/x86 due for the v5.13 merge window
Immutable branch between MFD and Power due for the v5.13 merge window
Immutable branch between MFD, PWM and RTC due for the v5.13 merge window
The ROHM BD71815 supports setting voltage levels/regulator status
for HW-states "RUN", "SUSPEND", "LPSR" and "SNVS". Add DT parsing
helper also for SNVS state.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add core support for ROHM BD71815 Power Management IC.
The IC integrates regulators, a battery charger with a coulomb counter,
a real-time clock (RTC), clock gate and general-purpose outputs (GPO).
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Sort the ID list so it is easier to see which ICs are present.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add chip ID for ROHM BD71815 and PMIC so that drivers can identify
this IC.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Most ROHM PMIC sub-devices only use the regmap pointer from
parent device. They can obtain this by dev_get_regamap so in
most cases the MFD device does not need to allocate and populate
the driver data. Simplify drivers by removing this.
The BD70528 still needs the access to watchdog mutex so keep
rohm_regmap_dev in use on BD70528 RTC and WDG drivers for now.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a slew of defines, structs and enums and even a
function call only relevant for the charging code that
still lives in <linux/mfd/abx500.h>. Push it down to the
"ab8500-bm.h" header in the power supply subsystem where
it is actually used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The charging algorithm header is only used locally in the
power supply subsystem so push this down into
drivers/power/supply and rename from the confusing
"ux500_chargalg.h" to "ab8500-chargalg.h" for clarity:
it is only used with the AB8500.
This is another remnant of non-DT code needing to pass
data from boardfiles, which we don't do anymore.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The global definition of platform data for the battery
management code has no utility after the OF conversion,
move the <linux/mfd/abx500/ab8500-bm.h> to be a local
file in drivers/power/supply and stop defining the
platform data in drivers/power/supply/ab8500_bmdata.c
and broadcast to the kernel only to have it assigned
as platform data to the MFD cells and then picked back
into the same subsystem that defined it in the first
place. This kills off a layer of indirection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add initial support for the Actions Semi ATC260x PMICs which integrates
Audio Codec, Power management, Clock generation and GPIO controller
blocks.
For the moment this driver only supports Regulator, Poweroff and Onkey
functionalities for the ATC2603C and ATC2609A chip variants.
Since the PMICs can be accessed using both I2C and SPI buses, the
following driver structure has been adopted:
-----> atc260x-core.c (Implements core functionalities)
/
ATC260x --------> atc260x-i2c.c (Implements I2C interface)
\
-----> atc260x-spi.c (Implements SPI interface - TODO)
Co-developed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Netronix embedded controller is a microcontroller found in some
e-book readers designed by the original design manufacturer Netronix,
Inc. It contains RTC, battery monitoring, system power management, and
PWM functionality.
This driver implements register access and version detection.
Third-party hardware documentation is available at:
https://github.com/neuschaefer/linux/wiki/Netronix-MSP430-embedded-controller
The EC supports interrupts, but the driver doesn't make use of them so
far.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
ROHM BD9576 contains safety features like over/under voltage detection,
over curren detection and over temperature detection. Add the
configuration register information.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
BD9573 and BD9576 support set of "protection" interrupts for "fatal"
issues. Those lead to SOC reset as PMIC shuts the power outputs. Thus
there is no relevant IRQ handling for them.
Few "detection" interrupts were added to the BD9576 with the idea that
SOC could take some recovery-action before error gets unrecoverable.
Unfortunately the BD9576 interrupt logic was not re-evaluated. IRQs
are not designed to be properly acknowleged - and IRQ line is kept
active for whole duration of error condition (in comparison to
informing only about state change).
For above reason, do not consider missing IRQ as error.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add core support for ROHM BD9576MUF and BD9573MUF PMICs which are
mainly used to power the R-Car series processors.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In order to group x86 related platform data move intel-spi.h to x86 folder.
While at it, remove duplicate inclusion in C file.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ta: s/x85/x86]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210304140820.56692-1-andriy.shevchenko@linux.intel.com
Drop support for depercated platforms using SFI, drop the entire
support for SFI that has been long deprecated too and make some
janitorial changes on top of that (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAmA2ZukSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxKcAP/RAkbRVFndhQIZYTCu74O64v86FjTBcS
3vvcKevVkBJiPJL1l10Yo3UMEYAbJIRZY00jkUjX7pq4eurELu6LwdMtJlHwh0p5
ZP5QeSdq1xN+9UGwBGXlnka2ypmD8fjbQyxHKErYgvmOl4ltFm40PyUC9GCVFLnW
/1o83t/dcmTtaOGPYWTW3HuCsbYqANG/x8PYAFeAk5dBxoSaNV69gAEuCYr1JC5N
Nie4x2m2I5v9egJFhy6rmRrpHPBvocCho+FipJFagSKWHPCI2rBSKESVOj23zWt2
eIWhK5T/ZR3OqQb9tZN6uAPJmBAerc3l7ZHZ1oFBP68MjUJJJhduQ+hNxljOyLLw
CVx0UhuancIWZdyJon5f7E9S9STZLIZ/3usx3K+7AZK+PSmH8d/UEIeXfkC0FcAr
eO3gwalB9KuhhXbVvihW79RkfkV5pTaMvVS7l1BffN4WE1dB9PKtJ8/MKFbGaTUF
4Rev6BdAEDqJrw6OIARvNcI6TAEhbKe5yIghzhQWn+fZ7oEm6f6fvFObBzD0KvQP
4RwYJhXU0gtK5yo/Ib1sUqjVQn8Jgqb7Xq46WZsP07Yc6O2Ws/86qCpX1GSCv5FU
1CZEJLGLGTbjDYOyMaUDfO/tI5kXG11e0Ss7Q+snWH4Iyhg0aNEYChKjOAFIxIxg
JJYOH8O5p2IP
=jlPz
-----END PGP SIGNATURE-----
Merge tag 'sfi-removal-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull Simple Firmware Interface (SFI) support removal from Rafael Wysocki:
"Drop support for depercated platforms using SFI, drop the entire
support for SFI that has been long deprecated too and make some
janitorial changes on top of that (Andy Shevchenko)"
* tag 'sfi-removal-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/platform/intel-mid: Update Copyright year and drop file names
x86/platform/intel-mid: Remove unused header inclusion in intel-mid.h
x86/platform/intel-mid: Drop unused __intel_mid_cpu_chip and Co.
x86/platform/intel-mid: Get rid of intel_scu_ipc_legacy.h
x86/PCI: Describe @reg for type1_access_ok()
x86/PCI: Get rid of custom x86 model comparison
sfi: Remove framework for deprecated firmware
cpufreq: sfi-cpufreq: Remove driver for deprecated firmware
media: atomisp: Remove unused header
mfd: intel_msic: Remove driver for deprecated platform
x86/apb_timer: Remove driver for deprecated platform
x86/platform/intel-mid: Remove unused leftovers (vRTC)
x86/platform/intel-mid: Remove unused leftovers (msic)
x86/platform/intel-mid: Remove unused leftovers (msic_thermal)
x86/platform/intel-mid: Remove unused leftovers (msic_power_btn)
x86/platform/intel-mid: Remove unused leftovers (msic_gpio)
x86/platform/intel-mid: Remove unused leftovers (msic_battery)
x86/platform/intel-mid: Remove unused leftovers (msic_ocd)
x86/platform/intel-mid: Remove unused leftovers (msic_audio)
platform/x86: intel_scu_wdt: Drop mistakenly added const
- Standardise MFD_CELL_* helpers
- New Drivers
- Add support for Acer Iconia Tab A500 Embedded Controller
- New Device Support
- Add support for ROHM BD9574MWF to BD9571MWV
- Add support for Intel Alder Lake PCH-P PCI to LPSS
- Add support for Intel Alder Lake PCH-S PCI to LPSS
- New Functionality
- Support ACPI enumeration; arizona
- Fix-ups
- Managed resources; bd9571mwv
- DT additions/fix-ups; bd9571mwv, iqs62x, max8997, gateworks-gsc, ene-kb930
- Convert to SPDX; bd9571mw
- Fix return values/error handling; sunxi
- Provide SOFTDEP; arizona
- Make use of DIV_ROUND_UP; mcp-sa11x0
- Use generic APIs; arizona
- Add MAC address sysfs entries; intel-m10-bmc
- Trivial: Coding-style fix-ups; iqs62x
- Trivial: Remove superflouous code; iqs62x
- Clear-up naming conventions; iqs62x
- Bug Fixes
- Fix 'pointer from integer' error; altera-sysmgr
- Convert SGI_MFD_IOC3 from tristate to bool; Kconfig
- Fix interrupt handling; gateworks-gsc
- Extend required delay; iqs62x
- Do not use I2C polling during calibration; iqs62x
- Do no adjust clock frequency during calibration; iqs62x
- Fix use-after-free; wm831x-auxad
-----BEGIN PGP SIGNATURE-----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=ieAS
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Standardise MFD_CELL_* helpers
New Drivers:
- Add support for Acer Iconia Tab A500 Embedded Controller
New Device Support:
- Add support for ROHM BD9574MWF to BD9571MWV
- Add support for Intel Alder Lake PCH-P PCI to LPSS
- Add support for Intel Alder Lake PCH-S PCI to LPSS
New Functionality:
- Support ACPI enumeration; arizona
Fix-ups:
- Managed resources; bd9571mwv
- DT additions/fix-ups; bd9571mwv, iqs62x, max8997, gateworks-gsc, ene-kb930
- Convert to SPDX; bd9571mw
- Fix return values/error handling; sunxi
- Provide SOFTDEP; arizona
- Make use of DIV_ROUND_UP; mcp-sa11x0
- Use generic APIs; arizona
- Add MAC address sysfs entries; intel-m10-bmc
- Trivial: Coding-style fix-ups; iqs62x
- Trivial: Remove superflouous code; iqs62x
- Clear-up naming conventions; iqs62x
Bug Fixes:
- Fix 'pointer from integer' error; altera-sysmgr
- Convert SGI_MFD_IOC3 from tristate to bool; Kconfig
- Fix interrupt handling; gateworks-gsc
- Extend required delay; iqs62x
- Do not use I2C polling during calibration; iqs62x
- Do no adjust clock frequency during calibration; iqs62x
- Fix use-after-free; wm831x-auxad"
* tag 'mfd-next-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (32 commits)
mfd: wm831x-auxadc: Prevent use after free in wm831x_auxadc_read_irq()
mfd: iqs62x: Do not change clock frequency during ATI
mfd: iqs62x: Do not poll during ATI
mfd: iqs62x: Increase interrupt handler return delay
mfd: iqs62x: Rename regmap_config struct
mfd: iqs62x: Remove unused bit mask
mfd: iqs62x: Remove superfluous whitespace above fallthroughs
mfd: intel-lpss: Add Intel Alder Lake PCH-S PCI IDs
mfd: intel-m10-bmc: Expose MAC address and count
mfd: Add driver for Embedded Controller found on Acer Iconia Tab A500
dt-bindings: mfd: Add ENE KB930 Embedded Controller binding
dt-bindings: mfd: gateworks-gsc: Add fan-tach mode
mfd: intel-lpss: Add Intel Alder Lake PCH-P PCI IDs
mfd: gateworks-gsc: Fix interrupt type
mfd: Standardise MFD_CELL_* helper names
mfd: mcp-sa11x0: Use DIV_ROUND_UP to calculate rw_timeout
mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell
dt-bindings: mfd: Correct the node name of the panel LED
mfd: sgi-ioc3: Turn Kconfig option into a bool
mfd: altera-sysmgr: Fix physical address storing more
...
Quite an active release for driver specific updates but very little
going on at the subsystem level this time for the regulator API.
- Overhaul of the Qualcomm LABIBB driver.
- Allow use of regulator_sync_voltage() on coupled regulators.
- Support for Action ATC260x, Mediatek DVSRC and MT6315, Qualcomm
PCM8180/c and PM8009-1 and Richtek RT4831
- Removal of the AB3100 driver.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAq2owACgkQJNaLcl1U
h9B1LQf/ShkuoDrWxPXNBkcxTd7F2SleqLw4c6rKo6ghNmyHzORnr/uDG1UKDJE9
DIkmmXJWPcqAzFeKfTCpmSuadbTgFbbjfdvWFEhS4a6xoRQ+Zk2cnsrx5JA+98Jy
kmHI7ACgzJUMCzXoPwPHUDg2iLSAuc+L5GcERIJDMqgszfCmCRWpvstH+XzmoJyP
gLfacrgrvFn/HtHR8xiMH4ueZxIgZqcDB4PVUDhgFQyMZt95+XwV43e9yyuvMcNh
Rxo+tjaYg5O7I9Lrmnt54PFJHmC4/ZmEF8RzjY8B9lRnhkpFt/JG61hfKp84Z0+E
OLqCU6b50Kd9aTd6Ep/etaDzNOSTuA==
=6tOD
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"Quite an active release for driver specific updates but very little
going on at the subsystem level this time for the regulator API.
Summary:
- Overhaul of the Qualcomm LABIBB driver.
- Allow use of regulator_sync_voltage() on coupled regulators.
- Support for Action ATC260x, Mediatek DVSRC and MT6315, Qualcomm
PCM8180/c and PM8009-1 and Richtek RT4831
- Removal of the AB3100 driver"
* tag 'regulator-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (49 commits)
regulator: bd718x7, bd71828, Fix dvs voltage levels
regulator: pca9450: Add sd-vsel GPIO
regulator: pca9450: Enable system reset on WDOG_B assertion
regulator: pca9450: Add SD_VSEL GPIO for LDO5
regulator: qcom-rpmh: fix pm8009 ldo7
regulator: mt6315: Add support for MT6315 regulator
regulator: document binding for MT6315 regulator
regulator: dt-bindings: Document charger-supply for max8997
regulator: qcom-labibb: Use disable_irq_nosync from isr
regulator: pf8x00: Fix typo for PF8200 chip name
regulator: pf8x00: set ramp_delay for bucks
regulator: core: Avoid debugfs: Directory ... already present! error
regulator: pf8x00: Add suspend support
regulator: Make regulator_sync_voltage() usable by coupled regulators
regulator: s5m8767: Drop regulators OF node reference
regulator: qcom-rpmh: Add pmc8180 and pmc8180c
regulator: qcom-rpmh: Add pmc8180 and pmc8180c
regulator: s5m8767: Fix reference count leak
regulator: remove ab3100 driver
regulator: axp20x: Fix reference cout leak
...
Here is the "big" set of staging and IIO driver patches for 5.12-rc1.
Nothing really huge in here, the number of staging tree patches has gone
down for a bit, maybe there's only so much churn to happen in here at
the moment.
The IIO changes are:
- new drivers
- new DT bindings
- new iio driver features
with full details in the shortlog.
The staging driver patches are just a lot of tiny coding style cleanups,
along with some semi-larger hikey driver cleanups as those are _almost_
good enough to get out of the staging tree, but will probably have to
wait until 5.13 to have happen.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYCqelQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymIDQCguWtPGy6U1sgaL3GAK/ROt2aet3wAn3TP1WgB
GeKAKKPshu3cskYQzlou
=UPZR
-----END PGP SIGNATURE-----
Merge tag 'staging-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver updates from Greg KH:
"Here is the "big" set of staging and IIO driver patches for 5.12-rc1.
Nothing really huge in here, the number of staging tree patches has
gone down for a bit, maybe there's only so much churn to happen in
here at the moment.
The IIO changes are:
- new drivers
- new DT bindings
- new iio driver features
with full details in the shortlog.
The staging driver patches are just a lot of tiny coding style
cleanups, along with some semi-larger hikey driver cleanups as those
are _almost_ good enough to get out of the staging tree, but will
probably have to wait until 5.13 to have happen.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (189 commits)
staging: hikey9xx: Fix alignment of function parameters
staging: greybus: Fixed a misspelling in hid.c
staging: wimax/i2400m: fix some byte order issues found by sparse
staging: wimax: i2400m: fix some incorrect type warnings
staging: greybus: minor code style fix
staging:wlan-ng: use memdup_user instead of kmalloc/copy_from_user
staging:r8188eu: use IEEE80211_FCTL_* kernel definitions
staging: rtl8192e: remove multiple blank lines
staging: greybus: Fixed alignment issue in hid.c
staging: wfx: remove unused included header files
staging: nvec: minor coding style fix
staging: wimax: Fix some coding style problem
staging: fbtft: add tearing signal detect
staging: vt6656: Fixed issue with alignment in rf.c
staging: qlge: Remove duplicate word in comment
staging: rtl8723bs: remove obsolete commented out code
staging: rtl8723bs: fix function comments to follow kernel-doc
staging: wfx: avoid defining array of flexible struct
staging: rtl8723bs: Replace one-element array with flexible-array member in struct ndis_80211_var_ie
staging: Replace lkml.org links with lore
...
The ROHM BD718x7 and BD71828 drivers support setting HW state
specific voltages from device-tree. This is used also by various
in-tree DTS files.
These drivers do incorrectly try to compose bit-map using enum
values. By a chance this works for first two valid levels having
values 1 and 2 - but setting values for the rest of the levels
do indicate capability of setting values for first levels as
well. Luckily the regulators which support setting values for
SUSPEND/LPSR do usually also support setting values for RUN
and IDLE too - thus this has not been such a fatal issue.
Fix this by defining the old enum values as bits and fixing the
parsing code. This allows keeping existing IC specific drivers
intact and only slightly changing the rohm-regulator.c
Fixes: 21b72156ed ("regulator: bd718x7: Split driver to common and bd718x7 specific parts")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210212080023.GA880728@localhost.localdomain
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. Commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") is also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers,
remove the support for outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After loading firmware, the driver triggers ATI (calibration) with
the newly loaded register configuration in place. Next, the driver
polls a register field to ensure ATI completed in a timely fashion
and that the device is ready to sense.
However, communicating with the device over I2C while ATI is under-
way may induce noise in the device and cause ATI to fail. As such,
the vendor recommends not to poll the device during ATI.
To solve this problem, let the device naturally signal to the host
that ATI is complete by way of an interrupt. A completion prevents
the sub-devices from being registered until this happens.
The former logic that scaled ATI timeout and filter settling delay
is not carried forward with the new implementation, as it produces
overly conservative delays at lower clock rates. Instead, a single
pair of delays that covers all cases is used.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Create two sysfs entries for exposing the MAC address and count
from the MAX10 BMC register space. The MAC address is the first
in a sequential block of MAC addresses reserved for the FPGA card.
The MAC count is the number of MAC addresses in the reserved block.
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Start all helpers with "MFD_CELL_".
Cc: Gene Chen <gene_chen@richtek.com>
Cc: linux-mediatek@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the IRQ list from the header, as this is used only
inside the driver itself. Also, get rid of two unused
defines.
The net result is that only struct hi6421_spmi_pmic remains
on it, as this is used by the regulator driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/138c3a11e4de0ebabdf27932957852136c2f7510.1611949675.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original driver, which can be seen at
commit 42f24d9d44 ("staging: regulator: add a regulator driver for HiSilicon 6421v600 SPMI PMIC")
had a complex logic to ensure that there won't be multiple power
enable/disable commands running at the same time. At the original
logic, it were ensured that:
- a next power up/down would wait for at least the on/off period;
- an extra delay would be granted. It turns that such extra delay
has a value of zero, but it was relying on gettimeofday()
call, which can take some time.
This was later simplified, but there are still some possible
issues. In order to avoid that, let's simply add a delay
to wait for the power up line to stabilize after powering up
a device.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/6733dac9813ba6688def404142cb7b964accf758.1611212783.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sunxi_rsb_driver::remove
return void, too. All users already unconditionally return 0, this
commit makes this obvious and ensures future users don't behave
differently. To simplify even further, make axp20x_device_remove()
return void instead of returning 0 unconditionally, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The new PMIC BD9574MWF inherits features from BD9571MWV.
Add the support of new PMIC to existing bd9571mwv driver.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the driver supports BD9571MWV PMIC only, this patch makes
the functions and data structure become more generic so that
it can support other PMIC variants as well. Also remove printing
part name which Lee Jones suggested.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@renesas.com>
Co-developed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the SPDX license identifier instead of a local description.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add chip IDs for BD9571MWV and BD9574MWF.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The struct ab8500_regulator_platform_data was a leftover
since the days before we probed all regulators from the
device tree. The ab8500-ext regulator was the only used,
defining platform data and register intialization that
was never used for anything, a copy of a boardfile no
longer in use.
Delete the ab8500_regulator_platform_data and make the
ab8500-ext regulator reference the regulator init data
in the local file directly. We are 100% device tree
these days.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201205004057.1712753-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- Add support for Intel's Platform Monitoring Technology (PMT)
- New Device Support
- Add support for PM660/PM660L to QCom SPMI PMIC
- Add support for lots of new devices to Kontron Core
- New Functionality
- Provide syscon_regmap_lookup_by_phandle_optional() to SysCon API
- Fix-ups
- Constify; da9xxx-core; intel_*, tps65xxx, wm8xxx-core, lp8788,
stmpe, sun4i-gpadc, 88pm800, hi655x-pmic, ioc3, etc
- Remove superfluous code; madera, tps65910
- Use raw APIs (rid abstractions); tps65911-comparator, tps65910
- Whitespace/formatting fix-ups; tps65910
- Device Tree changes/updates; bd71837-pmic, syscon
- Use helpers/APIs (no hand rolling); altera-sysmgr
- Mark of_match tables as __maybe_unused; twl6030-irq
- Fix spelling; si476x-core
- Bug Fixes
- Reset on resume to ensure known state; madera-core
- Correct ordering issues; madera-core, tps65910, kempld-core
- Remove erroneous passing of of_compatible strings; at91-usart
- Fix potential I2C adaptor leak; htc-i2cpld
- Correct errorneous defines; rt5033-private
- Resolve Kconfig issues; MFD_SL28CPLD, MFD_OMAP_USB_HOST
- Fix dev_err_probe() handling; stmfx
- Repair interrupt regression; motorola-cpcap
- Allow ACPI matching of DT tables; bcm590xx, da9xx, ene-kb3930,
fsl-imx25-tsadc, max77650,
mt6397-core, rt5033, stmfx,
max77686, sun4i-gpadc,
wm8994-core, axp20x-i2c
-----BEGIN PGP SIGNATURE-----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=Qp9q
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- Add support for Intel's Platform Monitoring Technology (PMT)
New Device Support:
- Add support for PM660/PM660L to QCom SPMI PMIC
- Add support for lots of new devices to Kontron Core
New Functionality:
- Provide syscon_regmap_lookup_by_phandle_optional() to SysCon API
Fix-ups:
- Constify; da9xxx-core; intel_*, tps65xxx, wm8xxx-core, lp8788,
stmpe, sun4i-gpadc, 88pm800, hi655x-pmic, ioc3, etc
- Remove superfluous code; madera, tps65910
- Use raw APIs (rid abstractions); tps65911-comparator, tps65910
- Whitespace/formatting fix-ups; tps65910
- Device Tree changes/updates; bd71837-pmic, syscon
- Use helpers/APIs (no hand rolling); altera-sysmgr
- Mark of_match tables as __maybe_unused; twl6030-irq
- Fix spelling; si476x-core
Bug Fixes:
- Reset on resume to ensure known state; madera-core
- Correct ordering issues; madera-core, tps65910, kempld-core
- Remove erroneous passing of of_compatible strings; at91-usart
- Fix potential I2C adaptor leak; htc-i2cpld
- Correct errorneous defines; rt5033-private
- Resolve Kconfig issues; MFD_SL28CPLD, MFD_OMAP_USB_HOST
- Fix dev_err_probe() handling; stmfx
- Repair interrupt regression; motorola-cpcap
- Allow ACPI matching of DT tables; bcm590xx, da9xx, ene-kb3930,
fsl-imx25-tsadc, max77650, mt6397-core, rt5033, stmfx, max77686,
sun4i-gpadc, wm8994-core, axp20x-i2c"
[ The PMT updates already came in through the x86 platform tree ]
* tag 'mfd-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (48 commits)
mfd: kempld-core: Add support for additional devices
mfd: si476x-core.h: Fix "regulator" spelling in comment
mfd: twl6030: Mark of_device_id table as maybe unused
mfd: axp20x: Skip of_device_id table when !CONFIG_OF
mfd: wm8994: Drop of_match_ptr from of_device_id table
mfd: sun4i: Drop of_match_ptr from of_device_id table
mfd: max77686: Drop of_match_ptr from of_device_id table
mfd: stmfx: Drop of_match_ptr from of_device_id table
mfd: rt5033: Drop of_match_ptr from of_device_id table
mfd: mt6397: Drop of_match_ptr from of_device_id table
mfd: max77650: Drop of_match_ptr from of_device_id table
mfd: fsl-imx25: Drop of_match_ptr from of_device_id table
mfd: ene-kb3930: Drop of_match_ptr from of_device_id table
mfd: da9150: Drop of_match_ptr from of_device_id table
mfd: da9063: Drop of_match_ptr from of_device_id table
mfd: da9062: Drop of_match_ptr from of_device_id table
mfd: da9055: Drop of_match_ptr from of_device_id table
mfd: bcm590xx: Drop of_match_ptr from of_device_id table
mfd: omap-usb: Depend on COMMON_CLK to fix compile tests
mfd: kempld-core: Check for DMI definition before ACPI
...
The H.264/H.265 Video Codec Unit v1.2 documentation describes this
register as follows:
Number of encoders core used for the provided configuration
This is required for configuring the VCU encoder buffer.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Link: https://lore.kernel.org/r/20201109134818.4159342-5-m.tretter@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Switch the "logicoreip" registers to the new xlnx,vcu-settings binding
to be able to read the settings if the settings are specified in a
separate device tree node that is shared with other drivers.
If the driver is not able to find a node with the new binding, fall back
to check for the logicore register bank to be backwards compatible.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Hyun Kwon <hyun.kwon@xilinx.com>
Link: https://lore.kernel.org/r/20201109134818.4159342-4-m.tretter@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set max_busy_timeouts for variants known to support the TOPxx bits in
the SD_OPTION register. The timeout mechanism was running in the
background but not yet properly handled in the driver. So, let the MMC
core know when to not use R1B to avoid unhandled timeouts.
My datasheets for older variants (tmio_mmc.c) suggest that they support
it, too. However, actual bit descriptions are lacking, so I chose an
opt-in approach.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201125213001.15003-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix regulators on rt5033 by converting some values to bitmasks which were
errorneously not defined as such in the header file.
Cc: Beomho Seo <beomho.seo@samsung.com>
Fixes: 0b27125854 ("mfd: rt5033: Add Richtek RT5033 driver core.")
Signed-off-by: Michael Srba <Michael.Srba@seznam.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An errata exists for cs47l15 where the reset must be handled
differently and removed before DCVDD is applied. A soft reset is used
for situations where a reset is required to reset state. This does
however, make this part unsuitable for DCVDD supplies with a rise time
greater than 2mS.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Client pointers in tps65910 data are not used in the drivers.
Remove those fields.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove wrappers around regmap calls to remove now-useless indirection.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The register field xxx_WIDTH defines are not used in current code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds syscon_regmap_lookup_by_phandle_optional() function to get an
optional regmap.
It behaves the same as syscon_regmap_lookup_by_phandle() except where
there is no regmap phandle. In this case, instead of returning -ENODEV,
the function returns NULL. This makes error checking simpler when the
regmap phandle is optional.
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Subsystem:
- new generic DT properties: aux-voltage-chargeable, trickle-voltage-millivolt
New driver:
- Microcrystal RV-3032
Drivers:
- ds1307: use aux-voltage-chargeable
- r9701, rx8010: modernization of the driver
- rv3028: fix clock output, trickle resistor values, RAM configuration
registers
-----BEGIN PGP SIGNATURE-----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=o9I0
-----END PGP SIGNATURE-----
Merge tag 'rtc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"A new driver this cycle is making the bulk of the changes and the
rx8010 driver has been rework to use the modern APIs.
Summary:
Subsystem:
- new generic DT properties: aux-voltage-chargeable,
trickle-voltage-millivolt
New driver:
- Microcrystal RV-3032
Drivers:
- ds1307: use aux-voltage-chargeable
- r9701, rx8010: modernization of the driver
- rv3028: fix clock output, trickle resistor values, RAM
configuration registers"
* tag 'rtc-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (50 commits)
rtc: r9701: set range
rtc: r9701: convert to devm_rtc_allocate_device
rtc: r9701: stop setting RWKCNT
rtc: r9701: remove useless memset
rtc: r9701: stop setting a default time
rtc: r9701: remove leftover comment
rtc: rv3032: Add a driver for Microcrystal RV-3032
dt-bindings: rtc: rv3032: add RV-3032 bindings
dt-bindings: rtc: add trickle-voltage-millivolt
rtc: rv3028: ensure ram configuration registers are saved
rtc: rv3028: factorize EERD bit handling
rtc: rv3028: fix trickle resistor values
rtc: rv3028: fix clock output support
rtc: mt6397: Remove unused member dev
rtc: rv8803: simplify the return expression of rv8803_nvram_write
rtc: meson: simplify the return expression of meson_vrtc_probe
rtc: rx8010: rename rx8010_init_client() to rx8010_init()
rtc: ds1307: enable rx8130's backup battery, make it chargeable optionally
rtc: ds1307: consider aux-voltage-chargeable
rtc: ds1307: store previous charge default per chip
...
Here is the large set of staging and IIO driver updates for 5.10-rc1.
Included in here are:
- new IIO drivers
- new IIO driver frameworks
- various IIO driver fixes and updates
- IIO device tree conversions to yaml
- so many minor staging driver coding style cleanups
- most cdev driver moved out of staging
- no new drivers added or removed
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX4g+oQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymAyQCghI58tN/Np3itPlZuc+HYFN7OHH8An1TKzCm1
bwkfw5qAcHab+R7KQZOA
=BaXS
-----END PGP SIGNATURE-----
Merge tag 'staging-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the large set of staging and IIO driver updates for 5.10-rc1.
Included in here are:
- new IIO drivers
- new IIO driver frameworks
- various IIO driver fixes and updates
- IIO device tree conversions to yaml
- so many minor staging driver coding style cleanups
- most cdev driver moved out of staging
- no staging drivers added or removed
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (476 commits)
staging: comedi: check validity of wMaxPacketSize of usb endpoints found
staging: wfx: improve robustness of wfx_get_hw_rate()
staging: wfx: drop unicode characters from strings
staging: wfx: gpiod_get_value() can return an error
staging: wfx: increase robustness of hif_generic_confirm()
staging: wfx: wfx_init_common() returns NULL on error
staging: wfx: standardize the error when vif does not exist
staging: wfx: check memory allocation
staging: wfx: improve error handling of hif_join()
staging: dpaa2-switch: add a dpaa2_switch prefix to all functions in ethsw.c
staging: dpaa2-switch: add a dpaa2_switch_ prefix to all functions in ethsw-ethtool.c
staging: rtl8188eu: Fix long lines
dt-bindings: staging: wfx: silabs,wfx yaml conversion
staging: wfx: update copyrights dates
staging: wfx: fix QoS priority for slow buses
staging: wfx: fix BA sessions for older firmwares
staging: wfx: remove remaining code of 'secure link' feature
staging: wfx: fix handling of MMIC error
staging: vchiq: Fix list_for_each exit tests
staging: greybus: use __force when assigning __u8 value to snd_ctl_elem_type_t
...
Removing the struct member "dev" in mt6397 RTC driver because it's not
initialized and the only usage is for one debugging message.
Also fixed a typo in the error message.
Signed-off-by: Fei Shao <fshao@chromium.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20201008093414.1911699-1-fshao@chromium.org
This patch implements the basic functions of the BMC chip for some Intel
FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the
Intel MAX 10 CPLD.
This BMC chip is connected to the FPGA by a SPI bus. To provide direct
register access from the FPGA, the "SPI slave to Avalon Master Bridge"
(spi-avmm) IP is integrated in the chip. It converts encoded streams of
bytes from the host to the internal register read/write on the Avalon
bus. So This driver uses the regmap-spi-avmm for register accessing.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the LP87524B/J/P-Q1 Four 4-MHz Buck Converter. This is a
variant of the LP87565 having 4 single-phase outputs and up to 10 A of
total output current.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On tc35894, have to disable direct keypad interrupts to make
it as general purpose interrupts functionality work.
if not, after chip reset, IRQST(0x91) will always 0x20,
IRQN always low level, can't be clear.
Configure DIRECTx to enable general purpose gpio mode,
else read GPIOMISx register always zero in irq routine.
verified on tc35894, need more test on other tc3589x.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Both irqnum and irqarray properties reflect the same thing:
the number of bits and bytes for interrupts at this
chipset. E. g.:
irqnum = 8 x irqarray
This can be seen by the way pending interrupts are handled:
/* During probe time */
pmic->irqs = devm_kzalloc(dev, pmic->irqnum * sizeof(int), GFP_KERNEL);
/* While handling IRQs */
for (i = 0; i < pmic->irqarray; i++) {
pending = hi6421_spmi_pmic_read(pmic, (i + pmic->irq_addr));
pending &= 0xff;
for_each_set_bit(offset, &pending, 8)
generic_handle_irq(pmic->irqs[offset + i * 8]);
}
Going further, there are some logic at the driver which assumes
that irqarray is 2:
/* solve powerkey order */
if ((i == HISI_IRQ_KEY_NUM) &&
((pending & HISI_IRQ_KEY_VALUE) == HISI_IRQ_KEY_VALUE)) {
generic_handle_irq(pmic->irqs[HISI_IRQ_KEY_DOWN]);
generic_handle_irq(pmic->irqs[HISI_IRQ_KEY_UP]);
pending &= (~HISI_IRQ_KEY_VALUE);
}
As HISI_IRQ_KEY_DOWN and HISI_IRQ_KEY_UP are fixed values
and don't depend on irqnum/irqarray.
The IRQ addr and mask addr seem to be also fixed, based on some
comments at the OF parsing code. So, get rid of them too,
removing the of parsing function completely.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/e231244e42cb5b56240705cac2f987e11a078038.1597762400.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several OF properties that aren't used by Hikey 970,
and some are not even used inside the driver.
So, drop them, as as this makes easier to document what's
actually used.
If latter needed, those could be re-added later.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/332f96c178b81bf1e9908a1da2127f043909ae0c.1597647359.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are some checks there which could make sense for
downstream builds, but doesn't make much sense for
upstream ones. They came from the official Hikey970 tree
from Linaro, but even there, the commented-out code is not
set via other Kconfig vars.
So, let's just get rid of that. If needed later, this
patch can be (partially?) reversed.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/ecbef801f6c32ba0850ad9e5c534a4304807df3b.1597647359.git.mchehab+huawei@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
- New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
- Driver Removal
- Remove unused driver for TI's SMSC ECE1099
- New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
- New Functionality
- Add support for AXP803 to be probed by I2C
- Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes; stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller
- Enabled Regmap 'fast I/O'; stm32-lptimer
- Change BUG_ON to WARN_ON; arizona-core
- Remove superfluous code/initialisation; madera, max14577
- Trivial formatting/spelling issues; madera-core, madera-i2c, da9055, max77693-private
- Switch to of_platform_populate(); sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros; lm3533-ctrlbank
- Disable IRQs on suspend; motorola-cpcap
- Clean-up error handling; intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices; madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique; syscon
- Bug Fixes
- Properly 'put' clock on unbind and error; arizona-core
- Fix revision handling; da9063
- Fix 'assignment of read-only location' error; kempld-core
- Avoid using the Regmap API when atomic; rn5t618
- Redefine volatile register description; rn5t618
- Use locking to protect event handler; dln2
-----BEGIN PGP SIGNATURE-----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=X/Zn
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
Driver Removal
- Remove unused driver for TI's SMSC ECE1099
New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
New Functionality
- Add support for AXP803 to be probed by I2C
Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes (stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller)
- Enabled Regmap 'fast I/O' in stm32-lptimer
- Change BUG_ON to WARN_ON in arizona-core
- Remove superfluous code/initialisation (madera, max14577)
- Trivial formatting/spelling issues (madera-core, madera-i2c, da9055, max77693-private)
- Switch to of_platform_populate() in sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros in lm3533-ctrlbank
- Disable IRQs on suspend in motorola-cpcap
- Clean-up error handling in intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices in madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique in syscon
Bug Fixes
- Properly 'put' clock on unbind and error in arizona-core
- Fix revision handling in da9063
- Fix 'assignment of read-only location' error in kempld-core
- Avoid using the Regmap API when atomic in rn5t618
- Redefine volatile register description in rn5t618
- Use locking to protect event handler in dln2"
* tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: syscon: Use a unique name with regmap_config
mfd: Replace HTTP links with HTTPS ones
mfd: dln2: Run event handler loop under spinlock
mfd: madera: Improve handling of regulator unbinding
mfd: mfd-core: Add mechanism for removal of a subset of children
mfd: intel_soc_pmic_mrfld: Simplify the return expression of intel_scu_ipc_dev_iowrite8()
mfd: max14577: Remove redundant initialization of variable current_bits
mfd: rn5t618: Fix caching of battery related registers
mfd: max77693-private: Drop a duplicated word
mfd: da9055: pdata.h: Drop a duplicated word
mfd: rn5t618: Make restart handler atomic safe
mfd: kempld-core: Fix 'assignment of read-only location' error
mfd: axp20x: Allow the AXP803 to be probed by I2C
mfd: da9063: Add support for latest DA silicon revision
mfd: da9063: Fix revision handling to correctly select reg tables
dt-bindings: mfd: st,stmfx: Remove I2C unit name
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
mfd: motorola-cpcap: Disable interrupt for suspend
mfd: smsc-ece1099: Remove driver
mfd: core: Add OF_MFD_CELL_REG() helper
...
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, the only way to remove MFD children is with a call to
mfd_remove_devices, which will remove all the children. Under
some circumstances it is useful to remove only a subset of the
child devices. For example if some additional clean up is required
between removal of certain child devices.
To accomplish this a level field is added to mfd_cell, the normal
mfd_remove_devices is modified to not remove devices that are set
to a higher level and a corresponding mfd_remove_devices_late
function is added to remove those children.
See further discussion at:
https://lore.kernel.org/lkml/20200616075834.GF2608702@dell/
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Drop the repeated word "that" in a comment.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This update adds new regmap tables to support the latest DA silicon
which will automatically be selected based on the chip and variant
information read from the device.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The current implementation performs checking in the i2c_probe()
function of the variant_code but does this immediately after the
containing struct has been initialised as all zero. This means the
check for variant code will always default to using the BB tables
and will never select AD. The variant code is subsequently set
by device_init() and later used by the RTC so really it's a little
fortunate this mismatch works.
This update adds raw I2C read access functionality to read the chip
and variant/revision information (common to all revisions) so that
it can subsequently correctly choose the proper regmap tables for
real initialisation.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This MFD driver has no user. The keypad driver of this device never made
it into the kernel. Therefore, this driver is useless. Remove it.
Signed-off-by: Michael Walle <michael@walle.cc>
Cc: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Extend current list of helpers to provide support for parent drivers
wishing to match specific child devices to particular OF nodes.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove unnecessary '\'s and leading tabs.
This will help to clean-up future diffs when subsequent changes are
made.
Hint: The aforementioned changes follow this patch.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, when a child platform device (sometimes referred to as a
sub-device) is registered via the Multi-Functional Device (MFD) API,
the framework attempts to match the newly registered platform device
with its associated Device Tree (OF) node. Until now, the device has
been allocated the first node found with an identical OF compatible
string. Unfortunately, if there are, say for example '3' devices
which are to be handled by the same driver and therefore have the same
compatible string, each of them will be allocated a pointer to the
*first* node.
An example Device Tree entry might look like this:
mfd_of_test {
compatible = "mfd,of-test-parent";
#address-cells = <0x02>;
#size-cells = <0x02>;
child@aaaaaaaaaaaaaaaa {
compatible = "mfd,of-test-child";
reg = <0xaaaaaaaa 0xaaaaaaaa 0 0x11>,
<0xbbbbbbbb 0xbbbbbbbb 0 0x22>;
};
child@cccccccc {
compatible = "mfd,of-test-child";
reg = <0x00000000 0xcccccccc 0 0x33>;
};
child@dddddddd00000000 {
compatible = "mfd,of-test-child";
reg = <0xdddddddd 0x00000000 0 0x44>;
};
};
When used with example sub-device registration like this:
static const struct mfd_cell mfd_of_test_cell[] = {
OF_MFD_CELL("mfd-of-test-child", NULL, NULL, 0, 0, "mfd,of-test-child"),
OF_MFD_CELL("mfd-of-test-child", NULL, NULL, 0, 1, "mfd,of-test-child"),
OF_MFD_CELL("mfd-of-test-child", NULL, NULL, 0, 2, "mfd,of-test-child")
};
... the current implementation will result in all devices being allocated
the first OF node found containing a matching compatible string:
[0.712511] mfd-of-test-child mfd-of-test-child.0: Probing platform device: 0
[0.712710] mfd-of-test-child mfd-of-test-child.0: Using OF node: child@aaaaaaaaaaaaaaaa
[0.713033] mfd-of-test-child mfd-of-test-child.1: Probing platform device: 1
[0.713381] mfd-of-test-child mfd-of-test-child.1: Using OF node: child@aaaaaaaaaaaaaaaa
[0.713691] mfd-of-test-child mfd-of-test-child.2: Probing platform device: 2
[0.713889] mfd-of-test-child mfd-of-test-child.2: Using OF node: child@aaaaaaaaaaaaaaaa
After this patch each device will be allocated a unique OF node:
[0.712511] mfd-of-test-child mfd-of-test-child.0: Probing platform device: 0
[0.712710] mfd-of-test-child mfd-of-test-child.0: Using OF node: child@aaaaaaaaaaaaaaaa
[0.713033] mfd-of-test-child mfd-of-test-child.1: Probing platform device: 1
[0.713381] mfd-of-test-child mfd-of-test-child.1: Using OF node: child@cccccccc
[0.713691] mfd-of-test-child mfd-of-test-child.2: Probing platform device: 2
[0.713889] mfd-of-test-child mfd-of-test-child.2: Using OF node: child@dddddddd00000000
Which is fine if all OF nodes are identical. However if we wish to
apply an attribute to particular device, we really need to ensure the
correct OF node will be associated with the device containing the
correct address. We accomplish this by matching the device's address
expressed in DT with one provided during sub-device registration.
Like this:
static const struct mfd_cell mfd_of_test_cell[] = {
OF_MFD_CELL_REG("mfd-of-test-child", NULL, NULL, 0, 1, "mfd,of-test-child", 0xdddddddd00000000),
OF_MFD_CELL_REG("mfd-of-test-child", NULL, NULL, 0, 2, "mfd,of-test-child", 0xaaaaaaaaaaaaaaaa),
OF_MFD_CELL_REG("mfd-of-test-child", NULL, NULL, 0, 3, "mfd,of-test-child", 0x00000000cccccccc)
};
This will ensure a specific device (designated here using the
platform_ids; 1, 2 and 3) is matched with a particular OF node:
[0.712511] mfd-of-test-child mfd-of-test-child.0: Probing platform device: 0
[0.712710] mfd-of-test-child mfd-of-test-child.0: Using OF node: child@dddddddd00000000
[0.713033] mfd-of-test-child mfd-of-test-child.1: Probing platform device: 1
[0.713381] mfd-of-test-child mfd-of-test-child.1: Using OF node: child@aaaaaaaaaaaaaaaa
[0.713691] mfd-of-test-child mfd-of-test-child.2: Probing platform device: 2
[0.713889] mfd-of-test-child mfd-of-test-child.2: Using OF node: child@cccccccc
This implementation is still not infallible, hence the mention of
"best effort" in the commit subject. Since we have not *insisted* on
the existence of 'reg' properties (in some scenarios they just do not
make sense) and no device currently uses the new 'of_reg' attribute,
we have to make an on-the-fly judgement call whether to associate the
OF node anyway. Which we do in cases where parent drivers haven't
specified a particular OF node to match to. So there is a *slight*
possibility of the following result (note: the implementation here is
convoluted, but it shows you one means by which this process can
still break):
/*
* First entry will match to the first OF node with matching compatible
* Second will fail, since the first took its OF node and is no longer available
* Third will succeed
*/
static const struct mfd_cell mfd_of_test_cell[] = {
OF_MFD_CELL("mfd-of-test-child", NULL, NULL, 0, 1, "mfd,of-test-child"),
OF_MFD_CELL_REG("mfd-of-test-child", NULL, NULL, 0, 2, "mfd,of-test-child", 0xaaaaaaaaaaaaaaaa),
OF_MFD_CELL_REG("mfd-of-test-child", NULL, NULL, 0, 3, "mfd,of-test-child", 0x00000000cccccccc)
};
The result:
[0.753869] mfd-of-test-parent mfd_of_test: Registering 3 devices
[0.756597] mfd-of-test-child: Failed to locate of_node [id: 2]
[0.759999] mfd-of-test-child mfd-of-test-child.1: Probing platform device: 1
[0.760314] mfd-of-test-child mfd-of-test-child.1: Using OF node: child@aaaaaaaaaaaaaaaa
[0.760908] mfd-of-test-child mfd-of-test-child.2: Probing platform device: 2
[0.761183] mfd-of-test-child mfd-of-test-child.2: No OF node associated with this device
[0.761621] mfd-of-test-child mfd-of-test-child.3: Probing platform device: 3
[0.761899] mfd-of-test-child mfd-of-test-child.3: Using OF node: child@cccccccc
We could code around this with some pre-parsing semantics, but the
added complexity required to cover each and every corner-case is not
justified. Merely patching the current failing (via this patch) is
already working with some pretty small corner-cases. Other issues
should be patched in the parent drivers which can be achieved simply
by implementing OF_MFD_CELL_REG().
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The only way the platform data for the SKY81452 ever gets populated
is through the device tree.
The MFD device is bothered with this for no reason at all. Just
allocate the platform data in the driver and be happy.
Cc: Gyungoh Yoo <jack.yoo@skyworksinc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This Microcontroller is present on the Khadas VIM1, VIM2, VIM3 and Edge
boards.
It has multiple boot control features like password check, power-on
options, power-off control and system FAN control on recent boards.
This implements a very basic MFD driver with the fan control and User
NVMEM cells.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This forward declaration is redundant since the header including the
full data structure is included.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add defines to be able to enable/clear irq and configure one shot mode.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Convert various DT (non-binding) doc files to ReST
- Various improvements to device link code
- Fix __of_attach_node_sysfs refcounting bug
- Add support for 'memory-region-names' with reserved-memory binding
- Vendor prefixes for Protonic Holland, BeagleBoard.org, Alps, Check
Point, Würth Elektronik, U-Boot, Vaisala, Baikal Electronics, Shanghai
Awinic Technology Co., MikroTik, Silex Insight
- A bunch more binding conversions to DT schema. Only 3K to go.
- Add a minimum version check for schema tools
- Treewide dropping of 'allOf' usage with schema references. Not needed
in new json-schema spec.
- Some formatting clean-ups of schemas
-----BEGIN PGP SIGNATURE-----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=/MDi
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Convert various DT (non-binding) doc files to ReST
- Various improvements to device link code
- Fix __of_attach_node_sysfs refcounting bug
- Add support for 'memory-region-names' with reserved-memory binding
- Vendor prefixes for Protonic Holland, BeagleBoard.org, Alps, Check
Point, Würth Elektronik, U-Boot, Vaisala, Baikal Electronics,
Shanghai Awinic Technology Co., MikroTik, Silex Insight
- A bunch more binding conversions to DT schema. Only 3K to go.
- Add a minimum version check for schema tools
- Treewide dropping of 'allOf' usage with schema references. Not needed
in new json-schema spec.
- Some formatting clean-ups of schemas
* tag 'devicetree-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (194 commits)
dt-bindings: clock: Add documentation for X1830 bindings.
dt-bindings: mailbox: Convert imx mu to json-schema
dt-bindings: power: Convert imx gpcv2 to json-schema
dt-bindings: power: Convert imx gpc to json-schema
dt-bindings: Merge gpio-usb-b-connector with usb-connector
dt-bindings: timer: renesas: cmt: Convert to json-schema
dt-bindings: clock: Convert i.MX8QXP LPCG to json-schema
dt-bindings: timer: Convert i.MX GPT to json-schema
dt-bindings: thermal: rcar-thermal: Add device tree support for r8a7742
dt-bindings: serial: Add binding for UART pin swap
dt-bindings: geni-se: Add interconnect binding for GENI QUP
dt-bindings: geni-se: Convert QUP geni-se bindings to YAML
dt-bindings: vendor-prefixes: Add Silex Insight vendor prefix
dt-bindings: input: touchscreen: edt-ft5x06: change reg property
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
dt-bindings: timer: renesas: mtu2: Convert to json-schema
of/fdt: Remove redundant kbasename function call
dt-bindings: clock: Convert i.MX1 clock to json-schema
dt-bindings: clock: Convert i.MX21 clock to json-schema
dt-bindings: clock: Convert i.MX25 clock to json-schema
...
- Constify 'properties' attribute in core header file
- New Drivers
- Add support for Gateworks System Controller
- Add support for MediaTek MT6358 PMIC
- Add support for Mediatek MT6360 PMIC
- Add support for Monolithic Power Systems MP2629 ADC and Battery charger
- Rework Intel's SCU IPC collection
- Eliminate near duplicate IPC functionality
- Split out MFD related activities into a dedicated MFD driver
- Fix-ups
- Use new I2C API; htc-i2cpld
- Remove superfluous code; sprd-sc27xx-spi
- Improve error handling; stm32-timers
- Device Tree additions/fixes; mt6397
- Defer probe betterment; wm8994-core
- Improve module handling; wm8994-core
- Staticify; stpmic1
- Trivial (spelling, formatting); tqmx86
- Bug Fixes
- Fix incorrect register/PCI IDs; intel-lpss-pci
- Fix unbalanced Regulator API calls; wm8994-core
- Fix double free(); wcd934x
- Remove IRQ domain on failure; stmfx
- Reset chip on resume; stmfx
- Disable/enable IRQs on suspend/resume; stmfx
- Do not use bulk writes on H/W which does not support them; max77620
-----BEGIN PGP SIGNATURE-----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=746a
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks:
- Constify 'properties' attribute in core header file
New Drivers:
- Add support for Gateworks System Controller
- Add support for MediaTek MT6358 PMIC
- Add support for Mediatek MT6360 PMIC
- Add support for Monolithic Power Systems MP2629 ADC and Battery charger
Fix-ups:
- Use new I2C API in htc-i2cpld
- Remove superfluous code in sprd-sc27xx-spi
- Improve error handling in stm32-timers
- Device Tree additions/fixes in mt6397
- Defer probe betterment in wm8994-core
- Improve module handling in wm8994-core
- Staticify in stpmic1
- Trivial (spelling, formatting) in tqmx86
Bug Fixes:
- Fix incorrect register/PCI IDs in intel-lpss-pci
- Fix unbalanced Regulator API calls in wm8994-core
- Fix double free() in wcd934x
- Remove IRQ domain on failure in stmfx
- Reset chip on resume in stmfx
- Disable/enable IRQs on suspend/resume in stmfx
- Do not use bulk writes on H/W which does not support them in max77620"
* tag 'mfd-next-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (29 commits)
mfd: mt6360: Remove duplicate REGMAP_IRQ_REG_LINE() entry
mfd: Add support for PMIC MT6360
mfd: max77620: Use single-byte writes on MAX77620
mfd: wcd934x: Drop kfree for memory allocated with devm_kzalloc
mfd: stmfx: Disable IRQ in suspend to avoid spurious interrupt
mfd: stmfx: Fix stmfx_irq_init error path
mfd: stmfx: Reset chip on resume as supply was disabled
mfd: wm8994: Silence warning about supplies during deferred probe
mfd: wm8994: Fix unbalanced calls to regulator_bulk_disable()
mfd: wm8994: Fix driver operation if loaded as modules
dt-bindings: mfd: mediatek: Add MT6397 Pin Controller
mfd: Constify properties in mfd_cell
mfd: stm32-timers: Use dma_request_chan() instead dma_request_slave_channel()
mfd: sprd: Remove unnecessary spi_bus_type setting
mfd: intel-lpss: Update LPSS UART #2 PCI ID for Jasper Lake
mfd: tqmx86: Fix a typo in MODULE_DESCRIPTION
mfd: stpmic1: Make stpmic1_regmap_config static
mfd: htc-i2cpld: Convert to use i2c_new_client_device()
MAINTAINERS: Add entry for mp2629 Battery Charger driver
power: supply: mp2629: Add impedance compensation config
...
* Add a support of the media keys on the ASUS laptop UX325JA/UX425JA
* ASUS WMI driver can now handle 2-in-1 models T100TA, T100CHI, T100HA, T200TA
* Big refactoring of Intel SCU driver with Elkhart Lake support has been added
* Slim Bootloarder firmware update signaling WMI driver has been added
* Thinkpad ACPI driver can handle dual fan configuration on new P and X models
* Touchscreen DMI driver has been extended to support
- MP-man MPWIN895CL tablet
- ONDA V891 v5 tablet
- techBite Arc 11.6
- Trekstor Twin 10.1
- Trekstor Yourbook C11B
- Vinga J116
* Virtual Button driver got a few fixes to detect mode of 2-in-1 tablet models
* Intel Speed Select tools update
* Plenty of small cleanups here and there
The following is an automated git shortlog grouped by driver:
acerhdf:
- replace space by * in modalias
New drivers:
- Add Elkhart Lake SCU/PMC support
- Add Slim Bootloader firmware update signaling driver
asus-laptop:
- Drop duplicate check for led_classdev_unregister()
asus-nb-wmi:
- Revert "Do not load on Asus T100TA and T200TA"
- Do not load on Asus T100TA and T200TA
asus-wmi:
- Ignore WMI events with code 0x79
- Add support for SW_TABLET_MODE
- Move asus_wmi_input_init and _exit lower in the file
- Drop duplicate check for led_classdev_unregister()
- Reserve more space for struct bias_args
- remove redundant initialization of variable status
dcdbas:
- Check SMBIOS for protected buffer address
dell-laptop:
- don't register micmute LED if there is no token
dell-wmi:
- Ignore keyboard attached / detached events
device property:
- export set_secondary_fwnode() to modules
eeepc-laptop:
- Drop duplicate check for led_classdev_unregister()
hp-wmi:
- Introduce HPWMI_POWER_FW_OR_HW as convenient shortcut
- Convert simple_strtoul() to kstrtou32()
- Refactor postcode_store() to follow standard patterns
intel_cht_int33fe:
- Fix spelling issues
- Switch to use acpi_dev_hid_uid_match()
- Convert to use set_secondary_fwnode()
- Convert software node array to group
intel-hid:
- Add a quirk to support HP Spectre X2 (2015)
intel_mid_powerbtn:
- Convert to use new SCU IPC API
intel_pmc_core:
- avoid unused-function warnings
- Change Jasper Lake S0ix debug reg map back to ICL
intel_pmc_ipc:
- Convert to MFD
- Move PCI IDs to intel_scu_pcidrv.c
- Drop intel_pmc_ipc_command()
- Start using SCU IPC
intel_scu_ipc:
- Add managed function to register SCU IPC
- Introduce new SCU IPC API
- Move legacy SCU IPC API to a separate header
- Log more information if SCU IPC command fails
- Split out SCU IPC functionality from the SCU driver
intel_scu_ipcutil:
- Convert to use new SCU IPC API
intel-speed-select:
- Fix speed-select-base-freq-properties output on CLX-N
intel_telemetry:
- Add telemetry_get_pltdata()
- Convert to use new SCU IPC API
intel-vbtn:
- Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type
- Detect switch position before registering the input-device
- Move detect_tablet_mode() to higher in the file
- Fix probe failure on devices with only switches
- Also handle tablet-mode switch on "Detachable" and "Portable" chassis-types
- Do not advertise switches to userspace if they are not there
- Split keymap into buttons and switches parts
- Use acpi_evaluate_integer()
ISST:
- Increase timeout
lg-laptop:
- Drop duplicate check for led_classdev_unregister()
MAINTAINERS:
- Add me as maintainer of Intel SCU drivers
- Update entry for Intel Broxton PMC driver
Merges of immutable branches:
- Merge branch 'for-next'
- Merge branch 'ib-mfd-x86-usb-watchdog-v5.7'
- Merge branch 'ib-pdx86-properties'
mfd:
- intel_soc_pmic_mrfld: Convert to use new SCU IPC API
- intel_soc_pmic_bxtwc: Convert to use new SCU IPC API
- intel_soc_pmic: Add SCU IPC member to struct intel_soc_pmic
samsung-laptop:
- Drop duplicate check for led_classdev_unregister()
software node:
- Allow register and unregister software node groups
sony-laptop:
- Make resuming thermal profile safer
- SNC calls should handle BUFFER types
thinkpad_acpi:
- Replace custom approach by kstrtoint()
- Use strndup_user() in dispatch_proc_write()
- Replace next_cmd(&buf) with strsep(&buf, ",")
- Drop duplicate check for led_classdev_unregister()
- Remove always false 'value < 0' statement
- Add support for dual fan control
tools/power/x86/intel-speed-select:
- Fix invalid core mask
- Increase CPU count
- Fix json perf-profile output output
- Update version
- Enable clos for turbo-freq enable
- Fix CLX-N package information output
- Check support status before enable
- Change debug to error
toshiba_acpi:
- Drop duplicate check for led_classdev_unregister()
touchscreen_dmi:
- Update Trekstor Twin 10.1 entry
- Add info for the Trekstor Yourbook C11B
- Drop comma in terminator line
- add Vinga J116 touchscreen
- Add info for the ONDA V891 v5 tablet
- Add touchscreen info for techBite Arc 11.6.
- Add info for the MP-man MPWIN895CL tablet
usb:
- typec: mux: Convert the Intel PMC Mux driver to use new SCU IPC API
watchdog:
- iTCO: fix link error
- intel-mid_wdt: Convert to use new SCU IPC API
wmi:
- Describe function parameters
- Fix indentation in some cases
- Replace UUID redefinitions by their originals
x86/platform/intel-mid:
- Add empty stubs for intel_scu_devices_[create|destroy]()
-----BEGIN PGP SIGNATURE-----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=pprB
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.8-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- Add a support of the media keys on the ASUS laptop UX325JA/UX425JA
- ASUS WMI driver can now handle 2-in-1 models T100TA, T100CHI, T100HA,
T200TA
- Big refactoring of Intel SCU driver with Elkhart Lake support has
been added
- Slim Bootloarder firmware update signaling WMI driver has been added
- Thinkpad ACPI driver can handle dual fan configuration on new P and X
models
- Touchscreen DMI driver has been extended to support
- MP-man MPWIN895CL tablet
- ONDA V891 v5 tablet
- techBite Arc 11.6
- Trekstor Twin 10.1
- Trekstor Yourbook C11B
- Vinga J116
- Virtual Button driver got a few fixes to detect mode of 2-in-1 tablet
models
- Intel Speed Select tools update
- Plenty of small cleanups here and there
* tag 'platform-drivers-x86-v5.8-1' of git://git.infradead.org/linux-platform-drivers-x86: (89 commits)
platform/x86: dcdbas: Check SMBIOS for protected buffer address
platform/x86: asus_wmi: Reserve more space for struct bias_args
platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type
platform/x86: intel-hid: Add a quirk to support HP Spectre X2 (2015)
platform/x86: touchscreen_dmi: Update Trekstor Twin 10.1 entry
platform/x86: touchscreen_dmi: Add info for the Trekstor Yourbook C11B
platform/x86: hp-wmi: Introduce HPWMI_POWER_FW_OR_HW as convenient shortcut
platform/x86: hp-wmi: Convert simple_strtoul() to kstrtou32()
platform/x86: hp-wmi: Refactor postcode_store() to follow standard patterns
platform/x86: acerhdf: replace space by * in modalias
platform/x86: ISST: Increase timeout
tools/power/x86/intel-speed-select: Fix invalid core mask
tools/power/x86/intel-speed-select: Increase CPU count
tools/power/x86/intel-speed-select: Fix json perf-profile output output
platform/x86: dell-wmi: Ignore keyboard attached / detached events
platform/x86: dell-laptop: don't register micmute LED if there is no token
platform/x86: thinkpad_acpi: Replace custom approach by kstrtoint()
platform/x86: thinkpad_acpi: Use strndup_user() in dispatch_proc_write()
platform/x86: thinkpad_acpi: Replace next_cmd(&buf) with strsep(&buf, ",")
platform/x86: intel-vbtn: Detect switch position before registering the input-device
...
The big change in this release is that Matti Vaittinen has factored out
the linear ranges support into a separate library in lib/ since it is
also useful for at least the power subsystem (and most likely others
too), it helps subsystems which need to map register values into more
useful real world values do so with minimal per-driver code.
- Factoring out of the linear ranges support into a library in lib/
from Matti Vaittinen.
- Trace points for bypass mode.
- Use the consumer name in debugfs to make it easier to understand.
- New drivers for Maxim MAX77826 and MAX8998.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl7U8oETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Fi+B/47cqB4/3uchKAXCHn4WE0hDANfeK4k
SkyBl9OH/UC0I/+V/nFrl1CfZgPMm18MuXG+D6fO+qqd1Df7EIgtehxh3MOjD15m
ZFFGybKBG2xg5G/dULE58/N5ZNTd03x8kgYePFmJEFe+m4qUvuICDEoOTHq+tvOO
sgeZPKYuipmGNrUAV4l49SSPuTFBhvAIg5VoR+K9TxxWAacMu7JM7GuGUMij8XwR
i1AryKGvDuCa7hfdWGVwbE+W/XmXiAWsmyz04YDXsYLTk9TjqviCJgf1Bst5EphP
ACr+KMDUIl+Y06wd7DE1UYnXtIxQg/MQ6wlJxG+wtIiZUt2vZcP2pbT6
=w291
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The big change in this release is that Matti Vaittinen has factored
out the linear ranges support into a separate library in lib/ since it
is also useful for at least the power subsystem (and most likely
others too), it helps subsystems which need to map register values
into more useful real world values do so with minimal per-driver code.
- Factoring out of the linear ranges support into a library in lib/
from Matti Vaittinen.
- Trace points for bypass mode.
- Use the consumer name in debugfs to make it easier to understand.
- New drivers for Maxim MAX77826 and MAX8998"
* tag 'regulator-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (23 commits)
regulator: max8998: max8998_set_current_limit() can be static
dt-bindings: regulator: Convert anatop regulator to json-schema
regulator: core: Add regulator bypass trace points
regulator: extract voltage balancing code to the separate function
regulator/mfd: max8998: Document charger regulator
regulator: max8998: Add charger regulator
MAINTAINERS: Add maintainer entry for linear ranges helper
regulator: bd718x7: remove voltage change restriction from BD71847 LDOs
lib: linear_ranges: Add missing MODULE_LICENSE()
regulator: use linear_ranges helper
power: supply: bd70528: rename linear_range to avoid collision
lib/test_linear_ranges: add a test for the 'linear_ranges'
lib: add linear ranges helpers
regulator: db8500-prcmu: Use true,false for bool variable
regulator: bd718x7: remove voltage change restriction from BD71847
regulator: max77826: Remove erroneous additionalProperties
regulator: qcom-rpmh: Fix typos in pm8150 and pm8150l
regulator: Document bindings for max77826
regulator: max77826: Add max77826 regulator driver
regulator: tps80031: remove redundant assignment to variables ret and val
...
Add MFD driver for mt6360 pmic chip include Battery Charger/
USB_PD/Flash, LED/RGB and LED/LDO/Buck
Signed-off-by: Gene Chen <gene_chen@richtek.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
When STMFX supply is stopped, spurious interrupt can occur. To avoid that,
disable the interrupt in suspend before disabling the regulator and
re-enable it at the end of resume.
Fixes: 06252ade91 ("mfd: Add ST Multi-Function eXpander (STMFX) core driver")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify 'struct property_entry *properties' in mfd_cell.
It is always passed around as a pointer const struct.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for 8-bit resolution ADC readings for input power
supply and battery charging measurement. Provides voltage, current
readings to mp2629 power supply driver.
Signed-off-by: Saravanan Sekar <sravanhome@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
