VF to VF traffic shouldn't go outside. To enforce it, set only the loopback
enable bit in case of all ingress type rules added via the tc tool.
Fixes: 0d08a441fb ("ice: ndo_setup_tc implementation for PF")
Reported-by: Sujai Buvaneswaran <Sujai.Buvaneswaran@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
igc_configure_rx_ring() function will be called as part of XDP program
setup. If Rx hardware timestamp is enabled prio to XDP program setup,
this timestamp enablement will be overwritten when buffer size is
written into SRRCTL register.
Thus, this commit read the register value before write to SRRCTL
register. This commit is tested by using xdp_hw_metadata bpf selftest
tool. The tool enables Rx hardware timestamp and then attach XDP program
to igc driver. It will display hardware timestamp of UDP packet with
port number 9092. Below are detail of test steps and results.
Command on DUT:
sudo ./xdp_hw_metadata <interface name>
Command on Link Partner:
echo -n skb | nc -u -q1 <destination IPv4 addr> 9092
Result before this patch:
skb hwtstamp is not found!
Result after this patch:
found skb hwtstamp = 1677800973.642836757
Optionally, read PHC to confirm the values obtained are almost the same:
Command:
sudo ./testptp -d /dev/ptp0 -g
Result:
clock time: 1677800973.913598978 or Fri Mar 3 07:49:33 2023
Fixes: fc9df2a0b5 ("igc: Enable RX via AF_XDP zero-copy")
Cc: <stable@vger.kernel.org> # 5.14+
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4fe815850b ("ixgbe: let the xdpdrv work with more than 64 cpus")
adds support to allow XDP programs to run on systems with more than
64 CPUs by locking the XDP TX rings and indexing them using cpu % 64
(IXGBE_MAX_XDP_QS).
Upon trying this out patch on a system with more than 64 cores,
the kernel paniced with an array-index-out-of-bounds at the return in
ixgbe_determine_xdp_ring in ixgbe.h, which means ixgbe_determine_xdp_q_idx
was just returning the cpu instead of cpu % IXGBE_MAX_XDP_QS. An example
splat:
==========================================================================
UBSAN: array-index-out-of-bounds in
/var/lib/dkms/ixgbe/5.18.6+focal-1/build/src/ixgbe.h:1147:26
index 65 is out of range for type 'ixgbe_ring *[64]'
==========================================================================
BUG: kernel NULL pointer dereference, address: 0000000000000058
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP NOPTI
CPU: 65 PID: 408 Comm: ksoftirqd/65
Tainted: G IOE 5.15.0-48-generic #54~20.04.1-Ubuntu
Hardware name: Dell Inc. PowerEdge R640/0W23H8, BIOS 2.5.4 01/13/2020
RIP: 0010:ixgbe_xmit_xdp_ring+0x1b/0x1c0 [ixgbe]
Code: 3b 52 d4 cf e9 42 f2 ff ff 66 0f 1f 44 00 00 0f 1f 44 00 00 55 b9
00 00 00 00 48 89 e5 41 57 41 56 41 55 41 54 53 48 83 ec 08 <44> 0f b7
47 58 0f b7 47 5a 0f b7 57 54 44 0f b7 76 08 66 41 39 c0
RSP: 0018:ffffbc3fcd88fcb0 EFLAGS: 00010282
RAX: ffff92a253260980 RBX: ffffbc3fe68b00a0 RCX: 0000000000000000
RDX: ffff928b5f659000 RSI: ffff928b5f659000 RDI: 0000000000000000
RBP: ffffbc3fcd88fce0 R08: ffff92b9dfc20580 R09: 0000000000000001
R10: 3d3d3d3d3d3d3d3d R11: 3d3d3d3d3d3d3d3d R12: 0000000000000000
R13: ffff928b2f0fa8c0 R14: ffff928b9be20050 R15: 000000000000003c
FS: 0000000000000000(0000) GS:ffff92b9dfc00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000058 CR3: 000000011dd6a002 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
ixgbe_poll+0x103e/0x1280 [ixgbe]
? sched_clock_cpu+0x12/0xe0
__napi_poll+0x30/0x160
net_rx_action+0x11c/0x270
__do_softirq+0xda/0x2ee
run_ksoftirqd+0x2f/0x50
smpboot_thread_fn+0xb7/0x150
? sort_range+0x30/0x30
kthread+0x127/0x150
? set_kthread_struct+0x50/0x50
ret_from_fork+0x1f/0x30
</TASK>
I think this is how it happens:
Upon loading the first XDP program on a system with more than 64 CPUs,
ixgbe_xdp_locking_key is incremented in ixgbe_xdp_setup. However,
immediately after this, the rings are reconfigured by ixgbe_setup_tc.
ixgbe_setup_tc calls ixgbe_clear_interrupt_scheme which calls
ixgbe_free_q_vectors which calls ixgbe_free_q_vector in a loop.
ixgbe_free_q_vector decrements ixgbe_xdp_locking_key once per call if
it is non-zero. Commenting out the decrement in ixgbe_free_q_vector
stopped my system from panicing.
I suspect to make the original patch work, I would need to load an XDP
program and then replace it in order to get ixgbe_xdp_locking_key back
above 0 since ixgbe_setup_tc is only called when transitioning between
XDP and non-XDP ring configurations, while ixgbe_xdp_locking_key is
incremented every time ixgbe_xdp_setup is called.
Also, ixgbe_setup_tc can be called via ethtool --set-channels, so this
becomes another path to decrement ixgbe_xdp_locking_key to 0 on systems
with more than 64 CPUs.
Since ixgbe_xdp_locking_key only protects the XDP_TX path and is tied
to the number of CPUs present, there is no reason to disable it upon
unloading an XDP program. To avoid confusion, I have moved enabling
ixgbe_xdp_locking_key into ixgbe_sw_init, which is part of the probe path.
Fixes: 4fe815850b ("ixgbe: let the xdpdrv work with more than 64 cpus")
Signed-off-by: John Hickey <jjh@daedalian.us>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230425170308.2522429-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Similar to skb_eth_hdr() introduced in commit 96cc4b6958 ("macvlan: do
not assume mac_header is set in macvlan_broadcast()"), let's introduce a
skb_vlan_eth_hdr() helper which can be used in TX-only code paths to get
to the VLAN header based on skb->data rather than based on the
skb_mac_header(skb).
We also consolidate the drivers that dereference skb->data to go through
this helper.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
This series lowers the CPU usage of the ice driver when using its
provided /dev/gnss*.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
10 ms is a lot of time to spend busy-waiting. Sleeping is clearly
allowed here, because we have just returned from ice_sq_send_cmd(),
which takes a mutex.
On kernels with HZ=100, this msleep may be twice as long, but I don't
think it matters.
I did not actually observe any retries happening here.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The 'buf_cpy'-related code in ice_sq_send_cmd_retry() looks broken.
'buf' is nowhere copied into 'buf_cpy'.
The reason this does not cause problems is that all commands for which
'is_cmd_for_retry' is true go with a NULL buf.
Let's remove 'buf_cpy'. Add a WARN_ON in case the assumption no longer
holds in the future.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver polls for ice_sq_done() with a 100 µs period for up to 1 s
and it uses udelay to do that.
Let's use usleep_range instead. We know sleeping is allowed here,
because we're holding a mutex (cq->sq_lock). To preserve the total
max waiting time, measure the timeout in jiffies.
ICE_CTL_Q_SQ_CMD_TIMEOUT is used also in ice_release_res(), but there
the polling period is 1 ms (i.e. 10 times longer). Since the timeout was
expressed in terms of the number of loops, the total timeout in this
function is 10 s. I do not know if this is intentional. This patch keeps
it.
The patch lowers the CPU usage of the ice-gnss-<dev_name> kernel thread
on my system from ~8 % to less than 1 %.
I received a report of high CPU usage with ptp4l where the busy-waiting
in ice_sq_send_cmd dominated the profile. This patch has been tested in
that usecase too and it made a huge improvement there.
Tested-by: Brent Rowsell <browsell@redhat.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
sq_cmd_timeout is initialized to ICE_CTL_Q_SQ_CMD_TIMEOUT and never
changed, so just use the constant directly.
Suggested-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Double the GNSS data polling interval from 10 ms to 20 ms.
According to Karol Kolacinski from the Intel team, they have been
planning to make this change.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice-gnss-<dev_name> kernel thread, which reads data from the u-blox
GNSS module, keep a CPU core almost 100% busy. The main reason is that
it busy-waits for data to become available.
A simple improvement would be to replace the "mdelay(10);" in
ice_gnss_read() with sleeping. A better fix is to not do any waiting
directly in the function and just requeue this delayed work as needed.
The advantage is that canceling the work from ice_gnss_exit() becomes
immediate, rather than taking up to ~2.5 seconds (ICE_MAX_UBX_READ_TRIES
* 10 ms).
This lowers the CPU usage of the ice-gnss-<dev_name> thread on my system
from ~90 % to ~8 %.
I am not sure if the larger 0.1 s pause after inserting data into the
gnss subsystem is really necessary, but I'm keeping that as it was.
Of course, ideally the driver would not have to poll at all, but I don't
know if the E810 can watch for GNSS data availability over the i2c bus
by itself and notify the driver.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ethtool uses `ETHTOOL_GRXRINGS` to compute how many queues are supported
by RSS. The driver should return the smaller of either:
- The maximum number of RSS queues the device supports, OR
- The number of RX queues configured
Prior to this change, running `ethtool -X $iface default` fails if the
number of queues configured is larger than the number supported by RSS,
even though changing the queue count correctly resets the flowhash to
use all supported queues.
Other drivers (for example, i40e) will succeed but the flow hash will
reset to support the maximum number of queues supported by RSS, even if
that amount is smaller than the configured amount.
Prior to this change:
$ sudo ethtool -L eth1 combined 20
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 20 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
24: 8 9 10 11 12 13 14 15
32: 0 1 2 3 4 5 6 7
...
You can see that the flowhash was correctly set to use the maximum
number of queues supported by the driver (16).
However, asking the NIC to reset to "default" fails:
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this change, the flowhash can be reset to default which will use
all of the available RSS queues (16) or the configured queue count,
whichever is smaller.
Starting with eth1 which has 10 queues and a flowhash distributing to
all 10 queues:
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
...
Increasing the queue count to 48 resets the flowhash to distribute to 16
queues, as it did before this patch:
$ sudo ethtool -L eth1 combined 48
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Due to the other bugfix in this series, the flowhash can be set to use
queues 0-5:
$ sudo ethtool -X eth1 equal 5
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 0 1 2
8: 3 4 0 1 2 3 4 0
16: 1 2 3 4 0 1 2 3
...
Due to this bugfix, the flowhash can be reset to default and use 16
queues:
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 16 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 10 11 12 13 14 15
16: 0 1 2 3 4 5 6 7
...
Fixes: 91cd94bfe4 ("ixgbe: add basic support for setting and getting nfc controls")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
ixgbe currently returns `EINVAL` whenever the flowhash it set by ethtool
because the ethtool code in the kernel passes a non-zero value for hfunc
that ixgbe should allow.
When ethtool is called with `ETHTOOL_SRXFHINDIR`,
`ethtool_set_rxfh_indir` will call ixgbe's set_rxfh function
with `ETH_RSS_HASH_NO_CHANGE`. This value should be accepted.
When ethtool is called with `ETHTOOL_SRSSH`, `ethtool_set_rxfh` will
call ixgbe's set_rxfh function with `rxfh.hfunc`, which appears to be
hardcoded in ixgbe to always be `ETH_RSS_HASH_TOP`. This value should
also be accepted.
Before this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
Cannot set RX flow hash configuration: Invalid argument
After this patch:
$ sudo ethtool -L eth1 combined 10
$ sudo ethtool -X eth1 default
$ sudo ethtool -x eth1
RX flow hash indirection table for eth1 with 10 RX ring(s):
0: 0 1 2 3 4 5 6 7
8: 8 9 0 1 2 3 4 5
16: 6 7 8 9 0 1 2 3
24: 4 5 6 7 8 9 0 1
...
Fixes: 1c7cf0784e ("ixgbe: support for ethtool set_rxfh")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-04-17 (i40e)
This series contains updates to i40e only.
Alex moves setting of active filters to occur under lock and checks/takes
error path in rebuild if re-initializing the misc interrupt vector
failed.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: fix i40e_setup_misc_vector() error handling
i40e: fix accessing vsi->active_filters without holding lock
====================
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230417205245.1030733-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
While using i219-LM card currently it was only possible to achieve
about 60% of maximum speed due to regression introduced in Linux 5.8.
This was caused by TSO not being disabled by default despite commit
f29801030a ("e1000e: Disable TSO for buffer overrun workaround").
Fix that by disabling TSO during driver probe.
Fixes: f29801030a ("e1000e: Disable TSO for buffer overrun workaround")
Signed-off-by: Sebastian Basierski <sebastianx.basierski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230417205345.1030801-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add error handling of i40e_setup_misc_vector() in i40e_rebuild().
In case interrupt vectors setup fails do not re-open vsi-s and
do not bring up vf-s, we have no interrupts to serve a traffic
anyway.
Fixes: 41c445ff0f ("i40e: main driver core")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix accessing vsi->active_filters without holding the mac_filter_hash_lock.
Move vsi->active_filters = 0 inside critical section and
move clear_bit(__I40E_VSI_OVERFLOW_PROMISC, vsi->state) after the critical
section to ensure the new filters from other threads can be added only after
filters cleaning in the critical section is finished.
Fixes: 278e7d0b9d ("i40e: store MAC/VLAN filters in a hash with the MAC Address as key")
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Drivers call netdev_tx_completed_queue() right before
netif_txq_maybe_wake(). If BQL is enabled netdev_tx_completed_queue()
should issue a memory barrier, so we can depend on that separating
the stop check from the consumer index update, instead of adding
another barrier in netif_txq_maybe_wake().
This matters more than the barriers on the xmit path, because
the wake condition is almost always true. So we issue the
consumer side barrier often.
Wrap netdev_tx_completed_queue() in a local helper to issue
the barrier even if BQL is disabled. Keep the same semantics
as netdev_tx_completed_queue() (barrier only if bytes != 0)
to make it clear that the barrier is conditional.
Plus since macro gets pkt/byte counts as arguments now -
we can skip waking if there were no packets completed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Convert ixgbe to use the new macros, I think a lot of people
copy the ixgbe code. The only functional change is that the
unlikely() in ixgbe_clean_tx_irq() turns into a likely()
inside the new macro and no longer includes
total_packets && netif_carrier_ok(tx_ring->netdev)
which is probably for the best, anyway.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The VLAN filters info is currently being held in a list and 2 bitmaps
(active_cvlans and active_svlans). We are experiencing some racing where
data is not in sync in the list and bitmaps. For example, the VLAN is
initially added to the list but only when the PF replies, it is added to
the bitmap. If a user adds many V2 VLANS before the PF responds:
while [ $((i++)) ]
ip l add l eth0 name eth0.$i type vlan id $i
we might end up with more VLAN list entries than the designated limit.
Also, The "ip link show" will show more links added than the PF limit.
On the other and, the bitmaps are only used to check the number of VLAN
filters and to re-enable the filters when the interface goes from DOWN to
UP.
This patch gets rid of the bitmaps and uses the list only. To do that,
the states of the VLAN filter are modified:
1 - IAVF_VLAN_REMOVE: the entry needs to be totally removed after informing
the PF. This is the "ip link del eth0.$i" path.
2 - IAVF_VLAN_DISABLE: (new) the netdev went down. The filter needs to be
removed from the PF and then marked INACTIVE.
3 - IAVF_VLAN_INACTIVE: (new) no PF filter exists, but the user did not
delete the VLAN.
Fixes: 48ccc43ecf ("iavf: Add support VIRTCHNL_VF_OFFLOAD_VLAN_V2 during netdev config")
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The VLAN filter states are currently being saved as individual bits.
This is error prone as multiple bits might be mistakenly set.
Fix by replacing the bits with a single state enum. Also, add an
"ACTIVE" state for filters that are accepted by the PF.
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reset the FDIR counters when FDIR inits. Without this patch,
when VF initializes or resets, all the FDIR counters are not
cleaned, which may cause unexpected behaviors for future FDIR
rule create (e.g., rule conflict).
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Signed-off-by: Lingyu Liu <lingyu.liu@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When adding a FDIR filter, if ice_vc_fdir_set_irq_ctx returns failure,
the inserted fdir entry will not be removed and if ice_vc_fdir_write_fltr
returns failure, the fdir context info for irq handler will not be cleared
which may lead to inconsistent or memory leak issue. This patch refines
failure cases to resolve this issue.
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Simei Su <simei.su@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently in the i40e driver there is no implementation of different
MAC address handling depending on whether it is a legacy or primary.
Introduce new checks for VF to be able to specify its primary MAC
address based on the VIRTCHNL_ETHER_ADDR_PRIMARY type.
Primary MAC address are treated differently compared to legacy
ones in a scenario where:
1. If a unicast MAC is being added and it's specified as
VIRTCHNL_ETHER_ADDR_PRIMARY, then replace the current
default_lan_addr.addr.
2. If a unicast MAC is being deleted and it's type
is specified as VIRTCHNL_ETHER_ADDR_PRIMARY, then zero the
hw_lan_addr.addr.
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-30 (documentation, ice)
This series contains updates to driver documentation and the ice driver.
Tony removes links and addresses related to the out-of-tree driver from the
Intel ethernet driver documentation.
Jake removes a comment that is no longer valid to the ice driver.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: remove comment about not supporting driver reinit
Documentation/eth/intel: Remove references to SourceForge
Documentation/eth/intel: Update address for driver support
====================
Link: https://lore.kernel.org/r/20230330165935.2503604-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conflicts:
drivers/net/ethernet/mediatek/mtk_ppe.c
3fbe4d8c0e ("net: ethernet: mtk_eth_soc: ppe: add support for flow accounting")
924531326e ("net: ethernet: mtk_eth_soc: add missing ppe cache flush when deleting a flow")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 31c8db2c4f ("ice: implement devlink reinit action"), the ice
driver does support driver re-initialization via devlink reload. Remove the
stale comment indicating that the driver lacks this support from the
ice_devlink_ops structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix invalid registers dump from ethtool -d ethX after adapter self test
by ethtool -t ethY. It causes invalid data display.
The problem was caused by overwriting i40e_reg_list[].elements
which is common for ethtool self test and dump.
Fixes: 22dd9ae8af ("i40e: Rework register diagnostic")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230328172659.3906413-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The code implicitly assumes that the list iterator finds a correct
handle. If 'vsi_handle' is not found the 'old_agg_vsi_info' was
pointing to an bogus memory location. For safety a separate list
iterator variable should be used to make the != NULL check on
'old_agg_vsi_info' correct under any circumstances.
Additionally Linus proposed to avoid any use of the list iterator
variable after the loop, in the attempt to move the list iterator
variable declaration into the macro to avoid any potential misuse after
the loop. Using it in a pointer comparison after the loop is undefined
behavior and should be omitted if possible [1].
Fixes: 37c592062b ("ice: remove the VSI info from previous agg")
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/ [1]
Signed-off-by: Jakob Koschel <jkl820.git@gmail.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add profile conflict check while adding some FDIR rules to avoid
unexpected flow behavior, rules may have conflict including:
IPv4 <---> {IPv4_UDP, IPv4_TCP, IPv4_SCTP}
IPv6 <---> {IPv6_UDP, IPv6_TCP, IPv6_SCTP}
For example, when we create an FDIR rule for IPv4, this rule will work
on packets including IPv4, IPv4_UDP, IPv4_TCP and IPv4_SCTP. But if we
then create an FDIR rule for IPv4_UDP and then destroy it, the first
FDIR rule for IPv4 cannot work on pkt IPv4_UDP then.
To prevent this unexpected behavior, we add restriction in software
when creating FDIR rules by adding necessary profile conflict check.
Fixes: 1f7ea1cd6a ("ice: Enable FDIR Configure for AVF")
Signed-off-by: Junfeng Guo <junfeng.guo@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The current implementation causes ice_vsi_update() to update all VSI
fields based on the cached VSI context. This also assumes that the
ICE_AQ_VSI_PROP_Q_OPT_VALID bit is set. This can cause problems if the
VSI context is not correctly synced by the driver. Fix this by only
updating the fields that correspond to ICE_AQ_VSI_PROP_Q_OPT_VALID.
Also, make sure to save the updated result in the cached VSI context
on success.
Fixes: 348048e724 ("ice: Implement iidc operations")
Co-developed-by: Robert Malz <robertx.malz@intel.com>
Signed-off-by: Robert Malz <robertx.malz@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Tested-by: Jakub Andrysiak <jakub.andrysiak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
make modules W=1 returns:
.../ice/ice_txrx_lib.c:448: warning: Function parameter or member 'first_idx' not described in 'ice_finalize_xdp_rx'
.../ice/ice_txrx.c:948: warning: Function parameter or member 'ntc' not described in 'ice_get_rx_buf'
.../ice/ice_txrx.c:1038: warning: Excess function parameter 'rx_buf' description in 'ice_construct_skb'
Fix these warnings by adding and deleting the deviant arguments.
Fixes: 2fba7dc515 ("ice: Add support for XDP multi-buffer on Rx side")
Fixes: d7956d81f1 ("ice: Pull out next_to_clean bump out of ice_put_rx_buf()")
CC: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-21 (ice)
This series contains updates to ice driver only.
Piotr sets first_desc field for proper handling of Flow Director
packets.
Michal moves error checking for VF earlier in function to properly return
error before other checks/reporting; he also corrects VSI filter removal to
be done during VSI removal and not rebuild.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: remove filters only if VSI is deleted
ice: check if VF exists before mode check
ice: fix rx buffers handling for flow director packets
====================
Link: https://lore.kernel.org/r/20230321183641.2849726-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DMA coalescing is not applicable for i225 parts. This patch comes to tidy
up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There was a problem with resuming ping after conducting a PCI reset.
This commit adds two functions, igbvf_io_prepare and igbvf_io_done,
which, after being added to the pci_error_handlers struct,
will prepare the drivers for a PCI reset and then bring the interface up
and reset it after. This will prevent the driver from ending up in
incorrect state. Test_and_set_bit is highly reliable in this context,
so we are not including a timeout in this commit
This introduces 900ms - 1100ms of overhead to this operation but it's in
non-time-critical flow. And also allows the driver to continue
functioning after the reset.
Functionality documented in ethernet-controller-i350-datasheet 4.2.1.3
https://www.intel.com/content/www/us/en/products/details/ethernet/gigabit-controllers/i350-controllers/docs.html
Signed-off-by: Dawid Wesierski <dawidx.wesierski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Driver's .adjfine interface functions use adjust_by_scaled_ppm and
diff_by_scaled_ppm introduced in commit 1060707e38
("ptp: introduce helpers to adjust by scaled parts per million")
to calculate the required adjustment in a concise manner,
but not igb_ptp_adjfine_82580.
Fix it by introducing IGB_82580_BASE_PERIOD and changing function logic
to use diff_by_scaled_ppm.
Signed-off-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Initialize to zero structures to build a valid
Tx Packet used for the filter programming.
Fixes: a9219b332f ("i40e: VLAN field for flow director")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When a system with E810 with existing VFs gets rebooted the following
hang may be observed.
Pid 1 is hung in iavf_remove(), part of a network driver:
PID: 1 TASK: ffff965400e5a340 CPU: 24 COMMAND: "systemd-shutdow"
#0 [ffffaad04005fa50] __schedule at ffffffff8b3239cb
#1 [ffffaad04005fae8] schedule at ffffffff8b323e2d
#2 [ffffaad04005fb00] schedule_hrtimeout_range_clock at ffffffff8b32cebc
#3 [ffffaad04005fb80] usleep_range_state at ffffffff8b32c930
#4 [ffffaad04005fbb0] iavf_remove at ffffffffc12b9b4c [iavf]
#5 [ffffaad04005fbf0] pci_device_remove at ffffffff8add7513
#6 [ffffaad04005fc10] device_release_driver_internal at ffffffff8af08baa
#7 [ffffaad04005fc40] pci_stop_bus_device at ffffffff8adcc5fc
#8 [ffffaad04005fc60] pci_stop_and_remove_bus_device at ffffffff8adcc81e
#9 [ffffaad04005fc70] pci_iov_remove_virtfn at ffffffff8adf9429
#10 [ffffaad04005fca8] sriov_disable at ffffffff8adf98e4
#11 [ffffaad04005fcc8] ice_free_vfs at ffffffffc04bb2c8 [ice]
#12 [ffffaad04005fd10] ice_remove at ffffffffc04778fe [ice]
#13 [ffffaad04005fd38] ice_shutdown at ffffffffc0477946 [ice]
#14 [ffffaad04005fd50] pci_device_shutdown at ffffffff8add58f1
#15 [ffffaad04005fd70] device_shutdown at ffffffff8af05386
#16 [ffffaad04005fd98] kernel_restart at ffffffff8a92a870
#17 [ffffaad04005fda8] __do_sys_reboot at ffffffff8a92abd6
#18 [ffffaad04005fee0] do_syscall_64 at ffffffff8b317159
#19 [ffffaad04005ff08] __context_tracking_enter at ffffffff8b31b6fc
#20 [ffffaad04005ff18] syscall_exit_to_user_mode at ffffffff8b31b50d
#21 [ffffaad04005ff28] do_syscall_64 at ffffffff8b317169
#22 [ffffaad04005ff50] entry_SYSCALL_64_after_hwframe at ffffffff8b40009b
RIP: 00007f1baa5c13d7 RSP: 00007fffbcc55a98 RFLAGS: 00000202
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007f1baa5c13d7
RDX: 0000000001234567 RSI: 0000000028121969 RDI: 00000000fee1dead
RBP: 00007fffbcc55ca0 R8: 0000000000000000 R9: 00007fffbcc54e90
R10: 00007fffbcc55050 R11: 0000000000000202 R12: 0000000000000005
R13: 0000000000000000 R14: 00007fffbcc55af0 R15: 0000000000000000
ORIG_RAX: 00000000000000a9 CS: 0033 SS: 002b
During reboot all drivers PM shutdown callbacks are invoked.
In iavf_shutdown() the adapter state is changed to __IAVF_REMOVE.
In ice_shutdown() the call chain above is executed, which at some point
calls iavf_remove(). However iavf_remove() expects the VF to be in one
of the states __IAVF_RUNNING, __IAVF_DOWN or __IAVF_INIT_FAILED. If
that's not the case it sleeps forever.
So if iavf_shutdown() gets invoked before iavf_remove() the system will
hang indefinitely because the adapter is already in state __IAVF_REMOVE.
Fix this by returning from iavf_remove() if the state is __IAVF_REMOVE,
as we already went through iavf_shutdown().
Fixes: 974578017f ("iavf: Add waiting so the port is initialized in remove")
Fixes: a8417330f8 ("iavf: Fix race condition between iavf_shutdown and iavf_remove")
Reported-by: Marius Cornea <mcornea@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Filters shouldn't be removed in VSI rebuild path. Removing them on PF
VSI results in no rule for PF MAC after changing for example queues
amount.
Remove all filters only in the VSI remove flow. As unload should also
cause the filter to be removed introduce, a new function ice_stop_eth().
It will unroll ice_start_eth(), so remove filters and close VSI.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Setting trust on VF should return EINVAL when there is no VF. Move
checking for switchdev mode after checking if VF exists.
Fixes: c54d209c78 ("ice: Wait for VF to be reset/ready before configuration")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Kalyan Kodamagula <kalyan.kodamagula@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
There are likely no users of this driver as the hardware has been
discontinued since 2010. Remove the driver and all references to it
in documentation.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-16 (igb, igbvf, igc)
This series contains updates to igb, igbvf, and igc drivers.
Lin Ma removes rtnl_lock() when disabling SRIOV on remove which was
causing deadlock on igb.
Akihiko Odaki delays enabling of SRIOV on igb to prevent early messages
that could get ignored and clears MAC address when PF returns nack on
reset; indicating no MAC address was assigned for igbvf.
Gaosheng Cui frees IRQs in error path for igbvf.
Akashi Takahiro fixes logic on checking TAPRIO gate support for igc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2023-03-16 (iavf)
This series contains updates to iavf driver only.
Alex fixes incorrect check against Rx hash feature and corrects payload
value for IPv6 UDP packet.
Ahmed removes bookkeeping of VLAN 0 filter as it always exists and can
cause a false max filter error message.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
iavf: do not track VLAN 0 filters
iavf: fix non-tunneled IPv6 UDP packet type and hashing
iavf: fix inverted Rx hash condition leading to disabled hash
====================
Link: https://lore.kernel.org/r/20230316155316.1554931-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
