Some ASICs do not have GOP driver to copy vbios image into
VFCT table. And it will go to next check.
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It was leftover from radeon where it was required for some
specific old hardware. It hasn't been required for ages
and the driver already falls back to MMIO when legacy IO
is not available. Legacy IO also seems to be problematic on
on some thunderbolt devices. Drop it.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Interrupts on are non-reentrant on linux. This is just an ancient
leftover from radeon where irq processing was kicked of from different
places.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
memalloc_nofs_save/restore are no longer sufficient to prevent recursive
lock warnings when holding locks that can be taken in MMU notifiers. Use
memalloc_noreclaim_save/restore instead.
Fixes: f920e413ff ("mm: track mmu notifiers in fs_reclaim_acquire/release")
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
cause:
It is necessary to send ras disable command to ras-ta during gfx
block ras later init, because the ras capability is disable read
from vbios for vega20 gaming, but the ras context is released
during ras init process, this will cause send ras disable command
to ras-to failed.
how:
Delay releasing ras context, the ras context
will be released after gfx block later init done.
Changed from V1:
move release_ras_context into ras_resume
Changed from V2:
check BIT(UMC) is more reasonable before access eeprom table
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
arcturus and sienna_cichlid share the same version
of umc_info interface (umc_info v33). arcturus uses
umc_config to indicate ECC capability, while
sienna_cichlid uses umc_config1 to indicate ECC
capability. driver needs to check either umc_config
or umc_config1 to decide ECC capability for ASICs
that use umc_info v33 interface.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the drm_mm_node walking from the actual handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the drm_mm_node walking from the actual handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the drm_mm_node walking from the actual handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the drm_mm_node walking from the actual handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the drm_mm_node walking from the actual handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the drm_mm_node walking from the actual handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate the drm_mm_node walking from the actual handling.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allows to walk over the drm_mm nodes in a TTM resource object.
v2: squash in fix from Felix
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Oak Zeng <Oak.Zeng@amd.com>
Tested-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Arunpravin <Arunpravin.PaneerSelvam@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cleanup pdb0 bo before bo_fini gets called
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. make function mmhub_v1_7_setup_vm_pt_regs static
2. indent a if statement
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ioremap_cache is not supported on some architecture
such as s390. Put the codes into a #ifdef to fix
some compile error reported by test robot.
v2: squash in non-x86 fix
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reported-by: Kernel test robot <lkp@intel.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 73bf5cad26.
Fixed in newer firmware
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gfx_v8_0_parse_sq_irq() is using in_task() to distinguish if it is
invoked from a workqueue worker or directly from the interrupt handler.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
gfx_v8_0_parse_sq_irq() is invoked directly either from a worker or from
the interrupt service routine. The worker is only bypassed if the worker
is already busy.
Add an argument `from_wq' to gfx_v8_0_parse_sq_irq() which is true if
invoked from the worker.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
gfx_v9_0_get_gpu_clock_counter() acquires a mutex_t lock and is the only
caller of gfx_v9_0_kiq_read_clock().
If it safe to acquire a mutex_t then gfx_v9_0_get_gpu_clock_counter() is
always invoked from preemptible context.
Remove in_interrupt() because it superfluous as it will always return
false.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The usage of in_interrupt() in gmc_v*_process_interrupt() is intended to
use a different code path if invoked from the interrupt handler vs
invoked from the workqueue.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be separated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
gmc_v*_process_interrupt() is invoked via the ->process() callback
from amdgpu_ih_process() which in turn is invoked either from
amdgpu_irq_handler() (the interrupt handler) or from
amdgpu_irq_handle_*() which is a workqueue.
amdgpu_irq::ih is always processed from the interrupt handler, the other
three struct amdgpu_ih_ring members are processed from a workqueue.
Replace the in_interrupt() check with a comparison against adev->irq.ih.
A similar check is already done to check if the ih pointer is from
ih_soft.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a drm debug message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In gpu reset, XGMI TA unload will cause gpu hang.
Skip it on A+A aldebaran.
Signed-off-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU introduce the new interface to enable light Secondary Bus Reset mode, driver
enable it on passthrough + XGMI configuration
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Read eeprom through SMU doesn't works stable on XGMI reset during test.
skip it for now
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This recent change introduce SDMA interrupt info printing with irq->process function.
These functions do not require a set function to enable/disable the irq
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add IH function to allow caller to wait until ring entries are processed
until the checkpoint write pointer.
This will be primarily used by HMM to drain pending page fault interrupts
before memory unmap to prevent HMM from handling stale interrupts.
Suggested-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jonathan Kim <jonathan.kim@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FB BO should not be ttm_bo_type_kernel type and
amdgpufb_create_pinned_object() pins the FB BO anyway.
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In passthrough configuration, hypervisior will trigger the SBR(Secondary bus reset) to the devices
without sync to each other. This could cause device hang since for XGMI configuration, all the devices
within the hive need to be reset at a limit time slot. This serial of patches try to solve this issue
by co-operate with new SMU which will only do minimum house keeping to response the SBR request but don't
do the real reset job and leave it to driver. Driver need to do the whole sw init and minimum HW init
to bring up the SMU and trigger the reset(possibly BACO) on all the ASICs at the same time
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Andrey Grodzovsky andrey.grodzovsky@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The gmc.xgmi.head list originally is designed for device list in the XGMI hive. Mix use it
for reset purpose will prevent the reset function to adjust XGMI device list which is required
in next change
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Andrey Grodzovsky andrey.grodzovsky@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The MQD might not be initialized duirng first init period if the device need to be reset
druing probe. Driver need to proper init them in gpu recovery period
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu driver may be in reset state during init which will not initialize the kfd,
driver need to initialize the KFD after reset by check the flag
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit d86fd724e5.
Disable PSP RAP L0 self test until to RAP feature ready.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To initialize the framebuffer, call drm_gem_fb_init_with_funcs which
verifies that the BO size can fit the FB size by calculating the minimum
expected size of each plane.
The bug was caught using igt-gpu-tools test: kms_addfb_basic.too-high
and kms_addfb_basic.bo-too-small
Tested on ChromeOS Zork by turning on the display and running a YT
video.
=== Changes from v1 ===
1. Added new line under declarations.
2. Use C style comment.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Mark Yacoub <markyacoub@chromium.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some configurations don't have FB BAR enabled. Avoid reading ROM image
from FB BAR region in such cases.
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch sets 'AMDGPU_GEM_CREATE_CPU_GTT_USWC' as input
parameter flag, during object creation of an imported DMA
buffer.
In absence of this flag:
1. Function amdgpu_display_supported_domains() doesn't add
AMDGPU_GEM_DOMAIN_GTT as supported domain.
2. Due to which, Function amdgpu_display_user_framebuffer_create()
refuses to create framebuffer for imported DMA buffers.
3. Due to which, AddFB() IOCTL fails.
4. Due to which, amdgpu_present_check_flip() check fails in DDX
5. Due to which DDX driver doesn't allow flips (goes to blitting)
6. Due to which setting Freesync/VRR property fails for PRIME buffers.
So, this patch finally enables Freesync with PRIME buffer offloading.
v2 (chk): instead of just checking the flag we copy it over if the
exporter is an amdgpu device as well.
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Variable 'bp' seems to be unused residue from previous
logic, and is not required anymore.
Cc: Koenig Christian <christian.koenig@amd.com>
Cc: Deucher Alexander <alexander.deucher@amd.com>
Signed-off-by: Shashank Sharma <shashank.sharma@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This temporarily reverts freesync video patches since it causes regression with
eDP displays. This patch is a squashed revert of the following patches:
6f59f229f8 ("drm/amd/display: Skip modeset for front porch change")
d10cd527f5 ("drm/amd/display: Add freesync video modes based on preferred modes")
0eb1af2e82 ("drm/amd/display: Add module parameter for freesync video mode")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Anson Jacob <anson.jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Aldebaran uses more than 4M runtime TMR. The current
hard coded 4M TMR is not big enough for Aldebaran.
Increase it to 8M.
v2: Only do 8M size for ALDEBARAN (Hawking)
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The flag is only applied on fine-grained memory.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Oak Zeng <Oak.Zeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Page tables in vram mapping to cpu is changed from uncached to
cached in A+A, the snoop bit in VM_CONTEXTx_PAGE_TABLE_BASE_ADDR/
PDE0s/PDE1s/PDE2s/PTE.TFs has to be set so gpuvm walker snoop
page table data out of CPU cache.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New A+A HW supports cached vram mapped to cpu.
Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When connected to a host via xGMI, system fatal errors may trigger
warm reset, driver has no change to query edc status before reset.
Therefore in this case, driver should harvest previous error loging
registers during boot, instead of only resetting them.
v2:
1. IP's ras_manager object is created when its ras feature is enabled,
so change to query edc status after amdgpu_ras_late_init called
2. change to enable watchdog timer after finishing gfx edc init
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Reivewed-by: Hawking Zhang <hawking.zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is needed for best machine learning performance. XNACK can still
be enabled per-process if needed.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Tested-by: Alex Sierra <alex.sierra@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add PSP RAP L0 check when RAP TA is loaded.
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RAP TA is an optional firmware. if it doesn’t exist,
the driver should bypass psp_rap_invoke() function.
1. bypass psp_rap_invoke() when RAP TA is not loaded.
2. add new parameter (status) to query RAP TA status.
(the status value is different with psp_ta_invoke(),
3. fix the 'rap_status' MThread critical problem.
(used without lock)
Signed-off-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
