drivers/net/ethernet/freescale/fec.h
7d650df99d ("net: fec: add pm_qos support on imx6q platform")
40c79ce13b ("net: fec: add stop mode support for imx8 platform")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
According to the KSZ9477S datasheet, there is no global register
at 0x033C and 0x033D addresses.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9896 supports both SPI (already in) and I2C.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the KSZ9896 6-port Gigabit Ethernet Switch to the
ksz9477 driver.
Although the KSZ9896 is already listed in the device tree binding
documentation since a1c0ed24fe (dt-bindings: net: dsa: document
additional Microchip KSZ9477 family switches) the chip id
(0x00989600) is not recognized by ksz_switch_detect() and rejected
by the driver.
The KSZ9896 is similar to KSZ9897 but has only one configurable
MII/RMII/RGMII/GMII cpu port.
Signed-off-by: Romain Naour <romain.naour@skf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the interrupts for internal phy link detection for
LAN937x. The interrupt enable bits are active low. There is global
interrupt mask for each port. And each port has the individual interrupt
mask for TAS. QCI, SGMII, PTP, PHY and ACL.
The first level of interrupt domain is registered for global port
interrupt and second level of interrupt domain for the individual port
interrupts. The phy interrupt is enabled in the lan937x_mdio_register
function. Interrupt from which port is raised will be detected based on
the interrupt host data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the lan937x_reset_switch(), it masks all the switch and port
registers. In the Global_Int_status register, POR ready bit is write 1
to clear bit and all other bits are read only. So, this patch clear the
por_ready_int status bit by writing 1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct ksz_port doesn't have reference to ksz_device as of now. In order
to find out from which port interrupt has triggered, we need to pass the
struct ksz_port as a host data. When the interrupt is triggered, we can
get the port from which interrupt triggered, but to identify it is phy
interrupt we have to read status register. The regmap structure for
accessing the device register is present in the ksz_device struct. To
access the ksz_device from the ksz_port, the reference is added to it
with port number as well.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After driver refactoring we was running ksz9477 specific CPU port
configuration on ksz8 family which ended with kernel oops. So, make sure
we run this code only on ksz9477 compatible devices.
Tested on KSZ8873 and KSZ9477.
Fixes: da8cd08520 ("net: dsa: microchip: add support for common phylink mac link up")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use chip_id as other places of this code do it
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used. So, remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is not used on ksz9477 side. Remove it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This variable is unused. So, drop it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With code refactoring was introduced new variable internal_phy. Let's
use it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ9477
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason why PHYlib may access MII_CTRL1000 on the chip without GBit
support is only if chip provides wrong information about extended caps
register. This issue is now handled by ksz9477_r_phy_quirks()
With proper regmap_ranges provided for all chips we will be able to
catch this kind of bugs any way. So, remove this sanity check.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add register validation for KSZ8563.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is complex driver with support for different chips with different
layouts. To detect at least some bugs earlier, we should validate register
accesses by using regmap_access_table support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding regmap register access validation.
KSZ9893 compatible chips do not have "Output Clock Control Register
0x0103". So, avoid writing to it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now ksz_pread/ksz_pwrite can return error value. So, make use of it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz_read*/ksz_write* are able to return errors, so forward it.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY access may end with errors on different levels. So, allow to forward
return values where possible.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This issue was detected after adding support of regmap_ranges for KSZ8563R
chip. This chip is reporting extended registers support without having
actual extended registers. This made PHYlib request not existing
registers.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
KSZ8563 has two 100Mbit PHYs and CPU port with RGMII support. Since
1000Mbit configuration for the RGMII capable MAC is present, we should
use per port validation.
As main part of migration to per-port validation we need to rework
ksz9477_switch_init() function. Which is using undocumented
REG_GLOBAL_OPTIONS register to detect per-chip Gbit support. So, it is
related to some sort of risk for regressions.
To reduce this risk I compared the code with publicly available
documentations. This function will executed on following currently
supported chips:
struct ksz_chip_data OF compatible
KSZ9477 KSZ9477
KSZ9897 KSZ9897
KSZ9893 KSZ9893, KSZ9563
KSZ8563 KSZ8563
KSZ9567 KSZ9567
Only KSZ9893, KSZ9563, KSZ8563 document existence of 0xf ==
REG_GLOBAL_OPTIONS register with bit field description "SKU ID":
KSZ9893 0x0C
KSZ9563 0x1C
KSZ8563 0x3C
The existence of hidden flags is not documented.
KSZ9477, KSZ9897, KSZ9567 do not document this register at all.
Only KSZ8563 is documented as non Gbit chip: 100Mbit PHYs and RGMII CPU
port. So, this change should not introduce a regression for
configurations with properly used OF compatibles.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add separate entry for the KSZ8563 chip. According to the documentation
it can support Gbit only on RGMII port. So, we will need to be able to
describe in the followup patch.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().
Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.
This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/
Reported-by: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DSA has multiple ways of specifying a MAC connection to an internal PHY.
One requires a DT description like this:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
phy-mode = "internal";
};
(which is IMO the recommended approach, as it is the clearest
description)
but it is also possible to leave the specification as just:
port@0 {
reg = <0>;
}
and if the driver implements ds->ops->phy_read and ds->ops->phy_write,
the DSA framework "knows" it should create a ds->slave_mii_bus, and it
should connect to a non-OF-based internal PHY on this MDIO bus, at an
MDIO address equal to the port address.
There is also an intermediary way of describing things:
port@0 {
reg = <0>;
phy-handle = <&internal_phy>;
};
In case 2, DSA calls phylink_connect_phy() and in case 3, it calls
phylink_of_phy_connect(). In both cases, phylink_create() has been
called with a phy_interface_t of PHY_INTERFACE_MODE_NA, and in both
cases, PHY_INTERFACE_MODE_NA is translated into phy->interface.
It is important to note that phy_device_create() initializes
dev->interface = PHY_INTERFACE_MODE_GMII, and so, when we use
phylink_create(PHY_INTERFACE_MODE_NA), no one will override this, and we
will end up with a PHY_INTERFACE_MODE_GMII interface inherited from the
PHY.
All this means that in order to maintain compatibility with device tree
blobs where the phy-mode property is missing, we need to allow the
"gmii" phy-mode and treat it as "internal".
Fixes: 2c709e0bda ("net: dsa: microchip: ksz8795: add phylink support")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216320
Reported-by: Craig McQueen <craig@mcqueen.id.au>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Tested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Link: https://lore.kernel.org/r/20220818143250.2797111-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the ksz9477_fdb_dump function it reads the ALU control register and
exit from the timeout loop if there is valid entry or search is
complete. After exiting the loop, it reads the alu entry and report to
the user space irrespective of entry is valid. It works till the valid
entry. If the loop exited when search is complete, it reads the alu
table. The table returns all ones and it is reported to user space. So
bridge fdb show gives ff:ff:ff:ff:ff:ff as last entry for every port.
To fix it, after exiting the loop the entry is reported only if it is
valid one.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220816105516.18350-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the ksz8795 cpu configuration to use the ksz common
xmii set functions.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port. It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the refactoring for the ksz8_dev_ops from ksz8795.c to
ksz_common.c, the ksz8_r_mib_cnt has been missed. So this patch adds the
missing one.
Fixes: 6ec23aaaac ("net: dsa: microchip: move ksz_dev_ops to ksz_common.c")
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220718061803.4939-1-arun.ramadoss@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch removes the of_match_ptr() pointer when dereferencing the
ksz_dt_ids which produce the unused variable warning.
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ksz_switch_register(), we should call of_node_put() for the
reference returned by of_get_child_by_name() which has increased
the refcount.
Fixes: 912aae27c6 ("net: dsa: microchip: really look for phy-mode in port nodes")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220714153138.375919-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch add the LAN937x part support in the existing ksz_spi_probe.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal phy of the LAN937x are capable of 100Mbps Full duplex. The
xMII port of switch is capable of 10Mbps Full & Half Duplex, 100Mbps
Full & Half Duplex and 1000Mbps Half duplex. xMII port also supports Tx
and Rx Flow control.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for port_max_mtu, port_change_mtu and
port_fast_age dsa functionality.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch register mdio-bus for the lan937x series switch. mdio read
and write uses the vphy for accessing the phy register.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for the writing and reading of the phy registers.
LAN937x uses the Vphy indirect addressing method for accessing the phys.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic DSA driver support for lan937x and the device will be
configured through SPI interface.
It adds the lan937x_dev_ops in ksz_common.c file and tries to reuse the
functionality of ksz9477 series switch.
drivers/net/dsa/microchip/ path is already part of MAINTAINERS &
the new files come under this path. Hence no update needed to the
MAINTAINERS
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This switch is calculating tx/rx_bytes for all packets including pause.
So, include rx/tx_pause counter to rx/tx_packets to make tx/rx_bytes fit
to rx/tx_packets.
Link: https://lore.kernel.org/all/20220624220317.ckhx6z7cmzegvoqi@skbuf/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for pause specific stats.
Tested on ksz9477.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register size for the ksz8 switches is u8 and for ksz9477 series is
u16. To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the struct ksz8 from ksz8.h which is no longer
needed. The platform bus specific details are now deferenced through
dev->priv.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, there are two spi probes, one ksz8795_spi.c and other
ksz9477_spi.c. This patch combines two files into single ksz_spi.c. The
difference between the two are regmap config and struct ksz8. The regmap
config is assigned based on the platform data. And struct ksz8 is left
untouched, as it is used only ksz8795.c. It can be used for all
other switches also in future.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch delete the ksz8_switch_register and ksz9477_switch_register
since both are calling the ksz_switch_register function. Instead the
ksz_switch_register is called from the probe function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the ksz_dev_ops from individual files to ksz_common.c.
And the dev_ops is assigned to ksz_device based on the switch detect.
This reduces the redundant function and allows to reuse the
functionality for LAN937x which has similar register set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the two different menuconfig for ksz9477 and ksz8795
to single ksz_common. so that it can be extended for the other switch
like lan937x. And removes the export_symbols for the extern functions in
the ksz_common.h.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 'commit 3506b2f42d ("net: dsa: microchip: call
phy_remove_link_mode during probe")' phy_remove_link_mode is added in
the switch_register function after dsa_switch_register. In order to have
the common switch register function, moving this phylink validation to
phylink_get_caps validation hook.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present, ksz8795.c and ksz9477.c have separate dsa_switch_ops
structure initialization. This patch modifies the files such a way that
ksz switches has common dsa_switch_ops in the ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the setting the start bit from the individual switch
configuration to ksz_setup
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the enabling the multicast storm protection from
individual setup function to ksz_setup function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the 10% broadcast protection from the individual setup
to ksz_setup. In the ksz9477, broadcast protection is updated in reset
function.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch move the common initialization of switches to ksz_setup and
perform the switch specific initialization using the ksz_dev_ops
function pointer.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to transmit the STP BPDU packet to the CPU port, the STP
address 01-80-c2-00-00-00 has to be added to static alu table for
ksz8795 series switch. For the ksz9477 switch, there is reserved
multicast table which handles forwarding the particular set of
multicast address to cpu port. So enabling the multicast reserved table
and updated the cpu port index. The stp addr is enabled during the setup
phase using the enable_stp_addr pointer in struct ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To have the common set of initialization in ksz_setup, introduced the
new config_cpu_port member to ksz_dev_ops. Since both the ksz8795.c and
ksz9477.c configuring the cpu port in the setup function, introduced the
member.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames the shutdown to reset in ksz_dev_ops in order to use
the reset dev_ops in the ksz_setup.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch assigns the get_phy_flags & mtu hook of ksz8795 and ksz9477
in dsa_switch_ops to ksz_common. For get_phy_flags hooks,checks whether
the chip is ksz8863/kss8793 then it returns error for port1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch makes the dsa_switch_hook for fdbs to use ksz_common.c file.
And from ksz_common, individual switches fdb functions are called using
the dev->dev_ops. And removed the r_dyn_mac_table, r_sta_mac_table and
w_sta_mac_table from ksz_dev_ops as it is used only in ksz8795.c
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz_mdb_add/del in ksz_common.c is specific for the ksz8795.c file. The
ksz9477 has its separate ksz9477_port_mdb_add/del functions. This patch
moves the ksz8795 specific mdb functionality from ksz_common to ksz8795.
And this dsa_switch_ops hooks for ksz8795/ksz9477 are invoked through
the ksz_port_mdb_add/del.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch assigns the phylink_get_caps in ksz8795 and ksz9477 to
ksz_phylink_get_caps. And update their mac_capabilities in the
respective ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
At present, P_STP_CTRL register value is passed as parameter to
ksz_port_stp_state from the individual dsa_switch_ops hooks. This patch
update the function to retrieve the register value through the
ksz_chip_data member.
And add the static to ksz_update_port_member since it is not called
outside the ksz_common.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch updates the common port mirror add/del dsa_switch_ops in
ksz_common.c. The individual switches implementation is executed based
on the ksz_dev_ops function pointers.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch moves the vlan dsa_switch_ops such as vlan_add, vlan_del and
vlan_filtering from the individual files ksz8795.c, ksz9477.c to
ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
ksz8795 and ksz9477 implementation on phy read/write hooks are
different. This patch modifies the ksz9477 implementation same as
ksz8795 by updating the ksz9477_dev_ops structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This patch move the dsa hook get_tag_protocol to ksz_common file. And
the tag_protocol is returned based on the dev->chip_id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KSZ87xx and KSZ88xx have chip_id representation at reg location 0. And
KSZ9477 compatible switch and LAN937x switch have same chip_id detection
at location 0x01 and 0x02. To have the common switch detect
functionality for ksz switches, ksz_switch_detect function is
introduced.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ksz9477_switch_detect performs the detecting the chip id from the
location 0x00 and also check gigabit compatibility check & number of
ports based on the register global_options0. To prepare the common ksz
switch detect function, routine other than chip id read is moved to
ksz9477_switch_init.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The name, regs_size and overrides members in struct ksz_device are
unused. Hence remove it.
And host_mask is used in only place of ksz8795.c file, which can be
replaced by dev->info->cpu_ports
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add the support for phylink_get_caps for ksz8795 and ksz9477
series switch. It updates the struct ksz_switch_chip with the details of
the internal phys and xmii interface. Then during the get_caps based on
the bits set in the structure, corresponding phy mode is set.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mib->cnt_ptr resetting is handled in multiple places as part of
port_init_cnt(). Hence moved mib->cnt_ptr code to ksz common layer
and removed from individual product files.
Signed-off-by: Prasanna Vengateshan <prasanna.vengateshan@microchip.com>
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 uses the same algorithm for copying the ethtool
strings. Hence moved to ksz_common to remove the redundant code.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ksz8795 and ksz9477 init function initializes the memory to dev->ports,
mib counters and assigns the ds real number of ports. Since both the
routines are same, moved the allocation of port memory to
ksz_switch_register after init.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ksz88xx family has one set of mib_names. The ksz87xx, ksz9477,
LAN937x based switches has one set of mib_names. In order to remove
redundant declaration, moved the struct mib_names to ksz_chip_data
structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch perform the compatibility check for the device after the chip
detect is done. It is to prevent the mismatch between the device
compatible specified in the device tree and actual device found during
the detect. The ksz9477 device doesn't use any .data in the
of_device_id. But the ksz8795_spi uses .data for assigning the regmap
between 8830 family and 87xx family switch. Changed the regmap
assignment based on the chip_id from the .data.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the ksz_chip_data in ksz8795 and ksz9477 to ksz_common.
At present, the dev->chip_id is iterated with the ksz_chip_data and then
copy its value to the ksz_dev structure. These values are declared as
constant.
Instead of copying the values and referencing it, this patch update the
dev->info to the ksz_chip_data based on the chip_id in the init
function. And also update the ksz_chip_data values for the LAN937x based
switches.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port_cnt value in the structure is not used in the switch_init.
Instead it uses the fls(chip->cpu_port), this is due to one of port in
the ksz8794 unavailable. The cpu_port for the 8794 is 0x10, fls(0x10) =
5, hence updating it directly in the ksz_chip_data structure in order to
same with all the other switches in ksz8795.c and ksz9477.c files.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mib counters for the ksz9477 is same for the ksz9477 switch and
LAN937x switch. Hence moving it to ksz_common.c file in order to have it
generic function. The DSA hook get_stats64 now can call ksz_get_stats64.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220426091048.9311-1-arun.ramadoss@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
