vfe-170 and vfe-175 can be supported in the same file with some minimal
indirection to differentiate between the silicon versions.
sdm845 uses vfe-170, sc8280xp uses vfe-175-200. Lets rename the file to
capture its wider scope than vfe-170 only.
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add in functional logic throughout the code to support the sc8280xp.
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
This commit describes the hardware layout for the sc8280xp for the
following hardware blocks:
- 4 x VFE, 4 RDI per VFE
- 4 x VFE Lite, 4 RDI per VFE
- 4 x CSID
- 4 x CSID Lite
- 4 x CSI PHY
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Adds a CAMSS SoC identifier for the SC8280XP.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Add a PHY configuration sequence for the sc8280xp which uses a Qualcomm
Gen 2 version 1.1 CSI-2 PHY.
The PHY can be configured as two phase or three phase in C-PHY or D-PHY
mode. This configuration supports two-phase D-PHY mode.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
-----BEGIN PGP SIGNATURE-----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=YxyV
-----END PGP SIGNATURE-----
Merge tag 'media/v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- DVB budget legacy API was finally documented. It took only 20+ years
to get some documentation about it...
- hantro driver has gained support for STM32MP25 VDEC/VENC
- rkisp1 has gained support for i.MX8MP
- atomisp got rid of two items from its todo list. Still 5 items
pending for moving it out of staging
- lots of driver fixes, cleanups and improvements
* tag 'media/v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (252 commits)
media: rcar-isp: Disallow unbind of devices
media: usbtv: Remove useless locks in usbtv_video_free()
media: mediatek: vcodec: avoid -Wcast-function-type-strict warning
media: ttpci: fix two memleaks in budget_av_attach
media: go7007: fix a memleak in go7007_load_encoder
media: dvb-frontends: avoid stack overflow warnings with clang
media: pvrusb2: fix uaf in pvr2_context_set_notify
media: usb: s2255: Refactor s2255_get_fx2fw
media: ti: j721e-csi2rx: Convert to platform remove callback returning void
media: stm32-dcmipp: Convert to platform remove callback returning void
media: nxp: imx8-isi: Convert to platform remove callback returning void
media: nuvoton: Convert to platform remove callback returning void
media: chips-media: wave5: Convert to platform remove callback returning void
media: chips-media: wave5: Remove unnecessary semicolons
media: i2c: imx290: Fix IMX920 typo
media: platform: replace of_graph_get_next_endpoint()
media: i2c: replace of_graph_get_next_endpoint()
media: ivsc: csi: Make use of sub-device state
media: ivsc: csi: Swap SINK and SOURCE pads
media: ipu-bridge: Serialise calls to IPU bridge init
...
Rename min_buffers_needed into min_queued_buffers and update
the documentation about it.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil: Drop the change where min_queued_buffers + 1 buffers would be]
[hverkuil: allocated. Now this patch only renames this field instead of making]
[hverkuil: a functional change as well.]
[hverkuil: Renamed 3 remaining min_buffers_needed occurrences.]
Not all SC7280 devices ship with ChromeOS firmware. Other devices need
PAS for image authentication. That requires the predefined virtual
address ranges to be passed via scm calls. Define them to enable Venus
on non-CrOS SC7280 devices.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Luca Weiss <luca.weiss@fairphone.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Declare power-domain names "top", "ife0" and "ife1" eponymously for the
power-domains TITAN_TOP_GDSC, IFE_0_GDSC and IFE_1_GDSC respectively.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some platforms such as SC7280 have 3 CSIDs and 2 CSID-lites but current
code has hardcoded 2 as the maximum number of CSIDs. Remove the hardcoded
maximum number of VFEs to handle all possible combinations of CSIDs and
CSID-lites.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some platforms such as SC7280 have three VFEs and two VFE-lites. Current
code has hard-coded two as the maximum number of VFEs. Remove the
hard-coded maximum number of VFEs to handle all possible combinations of
VFEs and VFE-lites.
Signed-off-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202311200405.h6G4L9oe-lkp@intel.com
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Right now we use fixed indexes to assign power-domains, with a
requirement for the TOP GDSC to come last in the list.
Adding support for named power-domains means the declaration in the dtsi
can come in any order.
After this change we continue to support the old indexing - if a SoC
resource declaration or the in-use dtb doesn't declare power-domain names
we fall back to the default legacy indexing.
From this point on though new SoC additions should contain named
power-domains, eventually we will drop support for legacy indexing.
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Moving the location of the hooks to VFE power domains has several
advantages.
1. Separation of concerns and functional decomposition.
vfe.c should be responsible for and know best how manage
power-domains for a VFE, excising from camss.c follows this
principle.
2. Embedding a pointer to genpd in struct camss_vfe{} meas that we can
dispense with a bunch of kmalloc array inside of camss.c.
3. Splitting up titan top gdsc from vfe/ife gdsc provides a base for
breaking up magic indexes in dtsi.
Suggested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
For the various versions of VFE we have a boiler-plate
pm_domain_on/pm_domain_off callback pair of the general form.
- Error check.
Not always done but applicable to all.
- device_link_add (DL_FLAG_STATELESS | DL_FLAG_PM_RUNTIME |
DL_FLAG_RPM_ACTIVE);
- Error check returning -EINVAL on error.
- Return 0
Reduce the pattern down to a common callback. VFE 4.1 is a special case
which to me also indicates that it is worthwhile maintaining an indirection
for the vfe_pm_domain_{on|off} for now.
Otherwise lets chuck out a bunch of needlessly replicated code.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Suggested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Right now we use the top-level camss structure to provide pointers via
VFE id index back to genpd linkages.
In effect this hard-codes VFE indexes to power-domain indexes in the
dtsi and mandates a very particular ordering of power domains in the
dtsi, which bears no relationship to a real hardware dependency.
As a first step to rationalising the VFE power-domain code and breaking
the magic indexing in dtsi use per-VFE pointers to genpd linkages.
The top-level index in msm_vfe_subdev_init is still used to attain the
initial so no functional or logical change arises from this change.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
At the moment we have some complex code for determining if a VFE requires a
power-domain attachment. Particularly discordant in this scheme is the
subtle reliance on VFE and VFE Lite declaration ordering in our resources.
VFE id is used to determine if a VFE is lite or not and consequently if a
VFE requires power-domain attachment. VFE Lite though is not a correct
delineation between power-domain and non power-domain state since early
SoCs have neither VFE Lite nor power-domains attached to VFEs.
Introduce has_pd to the VFE resource structure to allow the CAMSS code to
understand if it needs to try to attach a power-domain for a given VFE.
As a side-effect from this we no longer need to care about VFE Lite or
non-Lite or the id number associated with either and which order the
VFE/VFE Lite was declared in.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Matti Lehtimäki <matti.lehtimaki@gmail.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
V4L2 subdev operations have moved from operating on a
v4l2_subdev_pad_config to a v4l2_subdev_state a long time ago. Fix
remaining incorrect references to pad config in comments.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Imagine that "->vfe_num" is zero, then the subtraction will underflow to
UINT_MAX. Plus it's just cleaner to use >= instead.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The firmware path for some of the resources is still the old format. This
fixes the path to address the firmware correctly using the new .mbn
format.
Signed-off-by: Patrick Whewell <patrick.whewell@sightlineapplications.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Array `data` in `struct hfi_sfr` is being used as a fake flexible array
at run-time:
drivers/media/platform/qcom/venus/hfi_venus.c:
1033 p = memchr(sfr->data, '\0', sfr->buf_size);
1034 /*
1035 * SFR isn't guaranteed to be NULL terminated since SYS_ERROR indicates
1036 * that Venus is in the process of crashing.
1037 */
1038 if (!p)
1039 sfr->data[sfr->buf_size - 1] = '\0';
1040
1041 dev_err_ratelimited(dev, "SFR message from FW: %s\n", sfr->data);
Fake flexible arrays are deprecated, and should be replaced by
flexible-array members. So, replace one-element array with a
flexible-array member in `struct hfi_sfr`.
While there, also annotate array `data` with __counted_by() to prepare
for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time via CONFIG_UBSAN_BOUNDS (for
array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
This results in no differences in binary output.
This issue was found with the help of Coccinelle, and audited and fixed
manually.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Supported codec bitmask is populated from the payload from venus firmware.
There is a possible case when all the bits in the codec bitmask is set. In
such case, core cap for decoder is filled and MAX_CODEC_NUM is utilized.
Now while filling the caps for encoder, it can lead to access the caps
array beyong 32 index. Hence leading to OOB write.
The fix counts the supported encoder and decoder. If the count is more than
max, then it skips accessing the caps.
Cc: stable@vger.kernel.org
Fixes: 1a73374a04 ("media: venus: hfi_parser: add common capability parser")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The hfi parser, parses the capabilities received from venus firmware and
copies them to core capabilities. Consider below api, for example,
fill_caps - In this api, caps in core structure gets updated with the
number of capabilities received in firmware data payload. If the same api
is called multiple times, there is a possibility of copying beyond the max
allocated size in core caps.
Similar possibilities in fill_raw_fmts and fill_profile_level functions.
Cc: stable@vger.kernel.org
Fixes: 1a73374a04 ("media: venus: hfi_parser: add common capability parser")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Buffer requirement, for different buffer type, comes from video firmware.
While copying these requirements, there is an OOB possibility when the
payload from firmware is more than expected size. Fix the check to avoid
the OOB possibility.
Cc: stable@vger.kernel.org
Fixes: 09c2845e8f ("[media] media: venus: hfi: add Host Firmware Interface (HFI)")
Reviewed-by: Nathan Hebert <nhebert@chromium.org>
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Read and write pointers are used to track the packet index in the memory
shared between video driver and firmware. There is a possibility of OOB
access if the read or write pointer goes beyond the queue memory size.
Add checks for the read and write pointer to avoid OOB access.
Cc: stable@vger.kernel.org
Fixes: d96d3f30c0 ("[media] media: venus: hfi: add Venus HFI files")
Signed-off-by: Vikash Garodia <quic_vgarodia@quicinc.com>
Signed-off-by: Stanimir Varbanov <stanimir.k.varbanov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
'pd' can be NULL, and in that case it shouldn't be passed to
PTR_ERR. Fixes a smatch warning:
drivers/media/platform/qcom/venus/pm_helpers.c:873 vcodec_domains_get() warn: passing zero to 'PTR_ERR'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Digging into the documentation we find that the DT_ID bitfield is used to
map the six bit DT to a two bit ID code. This value is concatenated to the
VC bitfield to create a CID value. DT_ID is the two least significant bits
of CID and VC the most significant bits.
Originally we set dt_id = vc * 4 in and then subsequently set dt_id = vc.
commit 3c4ed72a16 ("media: camss: sm8250: Virtual channels for CSID")
silently fixed the multiplication by four which would give a better
value for the generated CID without mentioning what was being done or why.
Next up I haplessly changed the value back to "dt_id = vc * 4" since there
didn't appear to be any logic behind it.
Hans asked what the change was for and I honestly couldn't remember the
provenance of it, so I dug in.
Link: https://lore.kernel.org/linux-arm-msm/edd4bf9b-0e1b-883c-1a4d-50f4102c3924@xs4all.nl/
Add a comment so the next hapless programmer doesn't make this same
mistake.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
A previous patch I had removed the returns from vfe_disable() since we
didn't trap any meaningful errors. Konrad pointed out vfe_reset() could
return an error, which is true.
Trap the vfe_reset() error code and throw it up the callstack.
Suggested-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We can move vfe_disable() into a common routine in the core VFE file
provided we make wm_stop() a VFE specific callback.
The callback is required to capture the case where VFE 17x currently isn't
VC enabled where as VFE 480 is.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Some VFEs have four RDIs apiece. Right now the ISR code has a hard-coded
value which tops-out at RDI2 meaning only three RDIs can be utilised in
practice.
Extend out the various routines in camss-vfe-17x.c to support the higher
RDI count.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Several of our upstream and soon-to-be upstream SoC CAMSS dtsi declare
csiphyX as opposed to the older clock name csiX_phy.
Right now the CAMSS code will fail to set the csiphyX clock even if we have
declared it in our list of clocks. For sdm845 and sm8250 we appear to "get
away" with this error, however on sc8280xp we don't.
The right approach here is to set the clock when it is declared. If a SoC
doesn't require or a SoC driver implementer doesn't think we need, then the
clock ought to simply be omitted from the clock list.
Include csiphyX in the set of permissible strings which will subsequently
lead to the csiphyX clock being set during csiphy_set_clock_rates() phase.
sdm845 and sm8250 will work with the code as-is so I've omitted this from a
suggested Fixes list.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The csiphyX_timer and csiX_phy values need not be hard-coded. We can
functionally decompose the string matching inside of a loop.
Static string values are brittle, difficult to extend and not required
anyway since the camss->res->csiphy_num value informs us of the number
of CSIPHYs and hence the set of potential clocks for a given CSIPHY.
In simple terms if we have five CSIPHYs we can have no more and no less
than five csiphy_timer clocks. Similarly csi_phy core clocks have a 1:1
relationship with the PHY they clock.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The number of Video Front End - VFE or Image Front End - IFE supported
with new SoCs can vary both for the full and lite cases.
For example sdm845 has one vfe_lite and two vfe interfaces with the vfe
clock called simply "vfe_lite" with no integer postfix. sc8280xp has four
vfe and four vfe lite blocks.
At the moment we declare vfe_lite0 and vfe_lite1 for sm8250 but never set
those clocks because we don't match the strings.
We need to support the following clock name formats
- vfeN
- vfe_liteN
- vfe_lite
with N being any reasonably sized integer.
There are two sites in this code which need to do the same thing,
constructing and matching strings with the pattern above, so encapsulate
the logic in one function.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
We have a very convoluted if/else legacy here which needs to be
rationalised to make it more sustainable.
Adding in another Soc or two will make some of these if statements into
increasingly large multi-clause behemoths.
Introduce switches in the obvious places to despaghetiify.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
From sdm845 onwards we need to ensure the VFE is powered on prior to
switching on the CSID.
Currently the code tests for sdm845, sm8250 and then does get/set. This is
not extensible and it turns out is not necessary either since vfe_get and
vfe_set reference count.
Remove the over-conservative SoC version check.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> # rb3 # db410c
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Each Video Front End - VFE - has a variable number of Raw Data Interfaces -
RDIs associated with it.
The CAMSS code started from a naive implementation where a fixed define was
used as a control in a for(){} loop iterating through RDIs.
That model scales badly. An attempt was made with VFE_LINE_NUM_GEN2 and
VFE_LINE_NUM_GEN1 to differentiate between SoCs but, the problem with that
is "gen1" and "gen2" have no meaning in the silicon. There is no fixed
constraint in the silicon between VFE and RDI, it is entirely up to the SoC
designers how many VFEs are populated and how many RDIs to associate with
each VFE.
As an example sdm845 has VFE version 175 and sm8250 VFE version 480.
sdm845 has 2 VFEs with 4 RDIs and 1 VFE Lite with 4 RDIs.
sm8250 has 2 VFEs with 3 RDIs and 2 VFE Lite with 4 RDIs.
Clearly then we need a more granular model to capture the necessary data.
The defines have gone away to be replaced with per-SoC data but, we haven't
populated the parameter data with the real values.
Let's call those values out now
msm8916:
1 x VFE
3 x RDI per VFE (not 4)
msm8996:
2 x VFE
3 x RDI per VFE (not 4)
sdm660:
2 x VFE
3 x RDI per VFE (not 4)
sdm845:
2 x VFE
4 x RDI per VFE (not 3)
1 x VFE Lite
4 x RDI per VFE Lite (not 3)
sm8250:
2 x VFE
3 x RDI per VFE (not 4)
2 x VFE Lite
4 x RDI per VFE Lite
This more complex and correct mapping was not possible prior to passing
values via driver data. Now that we have that change in place we can
correctly map VFEs to RDIs for each VFE.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
It is possible to pass all of the CAMSS subdevice internal operations
pointers from the controlling resources structure with an additional
pointer added to the resources structure.
This allows for the removal of most of the probe-time control structures.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
line_num indicates the number of RDI - raw data interface channels which
are associated with a given IFE/VFE - image/video front end.
On several SoCs the RDI number is not static for each VFE - for example
on sm8250 VFE Lite has four RDIs where regular VFE has three.
Assigning line_num statically in the subdev_init() phase initialises
each VFE to the lower number, meaning in practical terms that we are
lobbing off one RDI on some VFEs.
Interrupt handling uses static for (i = RDI0; i < RDI2; i++) {} in some
of our VFE blocks but this can't work for situations where we have a
mixture of VFE @ 3 RDI and VFE-lite @ 4 RDI blocks.
First step to remediate is to pass line_num from a compat string
controlled data-structure and do so on a per-VFE basis.
Later patches will assign the correct number of RDI blocks per VFE.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
The following variables are being assigned statically based on
compatible strings in the probe path.
* enum camss_version version;
* unsigned int csiphy_num;
* unsigned int csid_num;
* unsigned int vfe_num;
* unsigned int vfe_lite_num;
* unsigned int vfe_total_num;
Migrate those variables to resource parameters passed in on platform
probe arguments. The one caveat is for VFE it has been necessary to
intoduce a new variable vfe_total_num to capture the aggregate value of
vfe_num + vfe_lite_num.
All the rest of the changes are rote camss->variable to
camss->res->variable with the parameter tables now populating the listed
variables.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Pass the bandwidth table as a platform parameter not if/else derived
pointer to the static table.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is a lot of unnecessary if/elsing in this code that arguably
should never have made it upstream when adding a second let alone
subsequent SoC.
I'm guilty of not fixing the mess myself when adding in the sm8250.
Before adding in any new SoCs or resources lets take the time to cleanup
the resource passing.
First step is to pass the generic struct camss_resources as a parameter
per the compatible list.
Subsequent patches will address the other somewhat disparate strutures
which we are also doing if/else on and assigning statically.
Squashed down a commit to drop useless NULL assignment for ispif resources.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Rename non-specific struct resources {} to struct camss_subdev_resources {}
Each logical block in CAMSS has a number of regulators, clocks and resets
associated with it. We represent these blocks as v4l subdevices.
The name "struct camss_subdev_resources" is a more descriptive and accurate
name.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
There is no good reason to differentiate the two resource structures
here. As part of a general tidyup of the declaration and passing of
resources within in the CAMSS driver it will be advantageous to have
one unified resource structure.
The two structures are very similar anyway thus leading more credence
still to the argument there should be only one.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Platforms with qcom-camss use CSI-2, which means 1X16 is more correct
than 2X8. The fact that qcom-camss supported only 2X8 meant it was
incompatible with camera sensors it should have been compatible with.
For example, the ov5645 driver (correctly) reports that its format is
UYVY8_1X16 (after ba449bb562).
Since qcom-camss only supports 2X8, the qcom-camss system is
incompatible with the ov5645 driver, even though they should be
compatible.
This patch replaces all uses of UYVY8_2X8/VYUY8_2X8/YUYV8_2X8/YVYU8_2X8
with the equivalent 1X16 formats.
Signed-off-by: Martin Dørum <dorum@noisolation.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).
Tested with:
RAW10P format, VC0:
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
RAW10P format, VC1:
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
RAW8 format, VC0:
media-ctl --reset
media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
VC_MODE = 0 implies a two bit VC address.
VC_MODE = 1 is required for VCs with a larger address than two bits.
Fixes: eebe6d00e9 ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
define CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE BIT(7)
disjunction for gen2 ? BIT(7) : is a nop we are setting the same bit
either way.
Fixes: 4abb21309f ("media: camss: csiphy: Move to hardcode CSI Clock Lane number")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
check_clock doesn't account for vfe_lite which means that vfe_lite will
never get validated by this routine. Add the clock name to the expected set
to remediate.
Fixes: 7319cdf189 ("media: camss: Add support for VFE hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
