The XP-PEN Deco 01 V2 is a UGEE v2 device with a frame with 8 buttons.
Its pen has 2 buttons, supports tilt and pressure.
Add its ID in order to support the device.
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/839
Tested-by: Mark Waddoups <mwaddoups@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This partially reverts commit f6d910a89a ("HID: usbhid: Add ALWAYS_POLL quirk
for some mice"), as it turns out to break reboot on some platforms for reason
yet to be understood.
Fixes: f6d910a89a ("HID: usbhid: Add ALWAYS_POLL quirk for some mice")
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
I no longer work for Plantronics (aka Poly, aka HP) and do not have
access to the headsets in order to test. However, as noted by Maxim,
the other 32xx models that share the same base code set as the 3220
would need the same quirk. This patch adds the PIDs for the rest of
the Blackwire 32XX product family that require the quirk.
Plantronics Blackwire 3210 Series (047f:c055)
Plantronics Blackwire 3215 Series (047f:c057)
Plantronics Blackwire 3225 Series (047f:c058)
Quote from previous patch by Maxim Mikityanskiy
Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.
The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.
End quote
Signed-off-by: Terry Junge <linuxhid@cosmicgizmosystems.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery status is reported for the HP Envy x360 eu0009nv stylus even
though it does not have battery.
Prevent it from always reporting the battery as low (1%).
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/823
Reported-by: Ioannis Iliopoulos <jxftw2424@gmail.com>
Tested-by: Ioannis Iliopoulos <jxftw2424@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some additional USB mouse devices are needing ALWAYS_POLL quirk without
which they disconnect and reconnect every 60s.
Add below devices to the known quirk list.
CHERRY VID 0x046a, PID 0x000c
MICROSOFT VID 0x045e, PID 0x0783
PRIMAX VID 0x0461, PID 0x4e2a
Signed-off-by: Ankit Patel <anpatel@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Acer Aspire Switch V 10 (SW5-017)'s keyboard-dock uses the same
ITE controller setup as other Acer Switch 2-in-1's.
This needs special handling for the wifi on/off toggle hotkey as well as
to properly report touchpad on/off keypresses.
Add the USB-ids for the SW5-017's keyboard-dock with a quirk setting of
QUIRK_TOUCHPAD_ON_OFF_REPORT to fix both issues.
Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The MadCatz variant of the MMO7 mouse has the ID 0738:1713 and the same
quirks as the Saitek variant.
Signed-off-by: Samuel Bailey <samuel.bailey1@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Provide initial support for the DualSense Edge controller. The brings
support up to the level of the original DualSense, but won't yet provide
support for new features (e.g. reprogrammable buttons).
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
CC: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20221010212313.78275-3-roderick.colenbrander@sony.com
The Topre REALFORCE R2 firmware incorrectly reports that interface
descriptor number 1, input report descriptor 2's events are array events
rather than variable events. That particular report descriptor is used
to report keypresses when there are more than 6 keys held at a time.
This bug prevents events from this interface from being registered
properly, so only 6 keypresses (from a different interface) can be
registered at once, rather than full n-key rollover.
This commit fixes the bug by setting the correct value in a report_fixup
function.
The original bug report can be found here:
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/804
Thanks to Benjamin Tissoires for diagnosing the issue with the report
descriptor.
Signed-off-by: Harry Stern <harry@harrystern.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20220911003614.297613-1-harry@harrystern.net
The touchbar on Apple T2 Macs has 2 modes, one that shows the function
keys and other that shows the media controls. The user can use the fn
key on his keyboard to switch between the 2 modes.
On Linux, if people were using an external keyboard or mouse, the
touchbar failed to change modes on pressing the fn key with the following
in dmesg :-
[ 10.661445] apple-ib-als 0003:05AC:8262.0001: : USB HID v1.01 Device [Apple Inc. Ambient Light Sensor] on usb-bce-vhci-3/input0
[ 11.830992] apple-ib-touchbar 0003:05AC:8302.0007: input: USB HID v1.01 Keyboard [Apple Inc. Touch Bar Display] on usb-bce-vhci-6/input0
[ 12.139407] apple-ib-touchbar 0003:05AC:8102.0008: : USB HID v1.01 Device [Apple Inc. Touch Bar Backlight] on usb-bce-vhci-7/input0
[ 12.211824] apple-ib-touchbar 0003:05AC:8102.0009: : USB HID v1.01 Device [Apple Inc. Touch Bar Backlight] on usb-bce-vhci-7/input1
[ 14.219759] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 24.395670] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 34.635791] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 2 (-110)
[ 269.579233] apple-ib-touchbar 0003:05AC:8302.0007: tb: Failed to set touch bar mode to 1 (-110)
Add the USB IDs of the touchbar found in T2 Macs to HID have special
driver list to fix the issue.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to the Surface Go devices, the Elantech touchscreen/digitizer in
the Lenovo Yoga C630 mistakenly reports the battery of the stylus, and
always reports an empty battery.
Apply the HID_BATTERY_QUIRK_IGNORE quirk to ignore this battery and
prevent the erroneous low battery warnings.
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Parblo A610 PRO is a UGEE v2 device with a frame with 9 buttons
and a bitmap dial. Its pen has 2 buttons, supports tilt and pressure.
Add its ID in order to support the device.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco Pro S is a UGEE v2 device with a frame with 8 buttons,
a bitmap dial and a mouse. Its pen has 2 buttons, supports tilt and
pressure.
All the pieces to support it are already in place. Add its ID in order
to support the device.
The required Wireshark traces were captured by Jouke Witteveen.
For more information check [1].
Link: https://gitlab.freedesktop.org/libinput/libinput/-/issues/738 [1]
Tested-by: Jouke Witteveen <j.witteveen@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The XP-PEN Deco L (UGEE) needs to be initialized by sending a buffer of
magic data, discovered by sniffing the Windows driver traffic.
In order to differentiate UGEE tablets that need this kind of
initialization from the previous ones, name them v2 internally and
create an entry point for them.
After initialization, the template report descriptors can be discovered
by parsing a string descriptor, similar to the one exposed by HUION v1
devices.
Add all the required elements to support the device.
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to the Surface Go (1), the (Elantech) touchscreen/digitizer in
the Surface Go 2 mistakenly reports the battery of the stylus. Instead
of over the touchscreen device, battery information is provided via
bluetooth and the touchscreen device reports an empty battery.
Apply the HID_BATTERY_QUIRK_IGNORE quirk to ignore this battery and
prevent the erroneous low battery warnings.
Cc: stable@vger.kernel.org
Signed-off-by: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Similar to other UGEE pens, but the IDs were missing.
Signed-off-by: Roman Romanenko <romu4444@gmail.com>
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for one of the several Mega World USB game
controller with integrated force feedback. It is a HID based
memory-less game controller, with a weak motor on the left, and a
strong one on the right.
Signed-off-by: frank zago <frank@zago.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This keyboard has two modes: regular HID and a native mode, which is used
in Windows driver. Native mode disables (poor) middle mouse button
scrolling emulation and reports middle button and scrolling events with a
custom report ID, which could be better handled in the driver.
This commit adds functional button mapping and native scrolling support.
HID collection in Bluetooth mode for custom report ID=5 is broken and
is patched upon connection. The collection initially contains incorrect
Usage Minimum/Usage Maximum numbers and, more importantly, marks Input
as Variable, not Array, while reporting values as in Array.
The keyboard is very similar to Compact USB/Bluetooth Keyboard with
TrackPoint, that's why this patch reuses all of cptkbd functions, except
for input mapping.
Signed-off-by: Florian Klink <flokli@flokli.de>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a driver to enable the macro keys (M1 - M5) by default, these are
mapped to XF86Tools and XF86Launch5 - XF86Launch8. The driver remaps
them by default to macro keys with an option to retain the old mapping
which users most likely already use as there are many scripts to enable
the macro keys available on Github and other websites.
Signed-off-by: Jelle van der Waa <jvanderwaa@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds the necessary IDs and configuration for Macs with
the T2 Security chip.
Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net>
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since the 006d Huion PID is used by multiple tablets (at least HS64 and
HS610), rename its constant to a more general
"USB_DEVICE_ID_HUION_TABLET2".
Signed-off-by: Nikolai Kondrashov <spbnick@gmail.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the UGTABLET WP5540 digitizer tablet
devices. Without it, the pen moves the cursor, but neither the
buttons nor the tap sensor in the tip do work.
Signed-off-by: Sergio Costas <rastersoft@gmail.com>
Link: https://lore.kernel.org/r/63dece1d-91ca-1b1b-d90d-335be66896be@gmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Fix for SiGma Micro-based keyboards where all the modifier keys mapped
to Shift_L.
Co-developed-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: Desmond Lim <peckishrine@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery status on Elan tablet driver is reported for the HP ENVY x360
15t-dr100. There is no separate battery for the Elan controller resulting in a
battery level report of 0% or 1% depending on whether a stylus has interacted
with the screen. These low battery level reports causes a variety of bad
behavior in desktop environments. This patch adds the appropriate quirk to
indicate that the batery status is unused for this target.
Cc: stable@vger.kernel.org
Signed-off-by: Karl Kurbjun <kkurbjun@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a new driver for the LetSketch / VSON WP9620N drawing tablet. This
drawing tablet is also sold under other brand names such as Case U,
presumably this driver will work for all of them. But it has only been
tested with a LetSketch WP9620N model.
These tablets also work without a special HID driver, but then only
part of the active area works and both the pad and stylus buttons are
hardwired to special key-combos. E.g. the 2 stylus buttons send right
mouse clicks / resp. "e" key presses.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2005575
BugLink: https://github.com/DIGImend/digimend-kernel-drivers/issues/528
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery status is reported for the Asus UX550VE touchscreen even though
it does not have a battery. Prevent it from always reporting the
battery as low.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1897823
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add a HID_QUIRK_NO_INIT_REPORTS quirk for the
Microsoft Surface 3 (non pro) type-cover.
Trying to init the reports seems to confuse the type-cover and
causes 2 issues:
1. Despite hid-multitouch sending the command to switch the
touchpad to multitouch mode, it keeps sending events on the
mouse emulation interface.
2. The touchpad completely stops sending events after a reboot.
Adding the HID_QUIRK_NO_INIT_REPORTS quirk fixes both issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery status is reported for the HP Envy X360 Convertible 15-eu0xxx
even if it does not have a battery. Prevent it from always reporting the
battery as low.
Signed-off-by: Trevor Davenport <trevor.davenport@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
NitroKey produced a clone of U2F Zero with a different firmware,
which moved extra commands into the vendor range.
Disambiguate hardware revisions and select the correct configuration in
u2fzero_probe.
Link: https://github.com/Nitrokey/nitrokey-fido-u2f-firmware/commit/a93c16b41f
Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds support for the joy-con charging grip. The peripheral
essentially behaves the same as a pro controller, but with two joy-cons
attached to the grip. However the grip exposes the two joy-cons as
separate hid devices, so extra handling is required. The joy-con is
queried to check if it is a right or left joy-con (since the product ID
is identical between left/right when using the grip).
Since controller model detection is now more complicated, the various
checks for hid product values have been replaced with helper macros to
reduce code duplication.
Signed-off-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The hid-nintendo driver supports the Nintendo Switch Pro Controllers and
the Joy-Cons. The Pro Controllers can be used over USB or Bluetooth.
The Joy-Cons each create their own, independent input devices, so it is
up to userspace to combine them if desired.
Signed-off-by: Daniel J. Ogorchock <djogorchock@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ANSI, ISO, and JIS variants of this keyboard all have the same
product ID.
Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When a finger is on the screen, the UPERFECT Y portable touchscreen
monitor reports a contact in the first place. However, after this
initial report, contacts are not reported at the refresh rate of the
screen as required by the Windows 8 specs.
This behaviour triggers the release_timer, removing the fingers even
though they are still present.
To avoid it, add a new class, similar to MT_CLS_WIN_8 but without the
MT_QUIRK_STICKY_FINGERS quirk for this device.
Suggested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: José Expósito <jose.exposito89@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch enables side-buttons of Xiaomi Bluetooth mouse (specifically Xiaomi
Mi Dual Mode Wireless Mouse Silent Edition).
The mouse sends invalid button count in its HID Report Descriptor and this
patch just replaces its descriptor with corrected one. With this driver side
buttons work as expected acting like Back/Forward buttons.
Signed-off-by: Ilya Skriblovsky <ilyaskriblovsky@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This commit adds support for the Guitar Hero Live PS4 dongles.
These dongles require a "magic" USB control message to be sent
every 8 seconds otherwise the dongle will not report events where
the strumbar is hit while a fret is being held.
Note that the GHL_GUITAR_POKE_INTERVAL is reduced to 8 seconds in order
to support PS3, Wii U, and PS4 GHL dongles.
Also note that the constant for vendor id 0x1430 has been renamed from
Activision to RedOctane as self-declared by the device.
Co-developed-by: Pascal Giard <pascal.giard@etsmtl.ca>
Signed-off-by: Pascal Giard <pascal.giard@etsmtl.ca>
Signed-off-by: Daniel Nguyen <daniel.nguyen.1@ens.etsmtl.ca>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Prevent the ASUS Claymore keyboard from sending a suspend event
when the device sleeps itself. The suspend event causes a system
suspend if uncaught.
Signed off by: Luke D Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These chips report mute button events in bit 4 of their report without it
being part of the report descriptor.
Use a custom descriptor that maps this bit.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- support for LCD menu keys + LCD brightness control on the Logitech Z-10
speakers (with LCD) which use the same protocol as the G15 keyboards
from Hans de Goede
The Elantech touchscreen/digitizer in the Surface Go mistakenly reports
having a battery. This results in a low battery message every time you
try to use the pen.
This patch adds a quirk to ignore the non-existent battery and
gets rid of the false low battery messages.
Signed-off-by: Zoltan Tamas Vajda <zoltan.tamas.vajda@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
USB_VENDOR_ID_CORSAIR is defined twice in the same file with the same
value.
Signed-off-by: Hamza Mahfooz <someguy@effective-light.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Lenovo optical mouse with vendor id of 0x17ef and product id of
0x600e experiences disconnecting issues every 55 seconds:
[38565.706242] usb 1-1.4: Product: Lenovo Optical Mouse
[38565.728603] input: Lenovo Optical Mouse as /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.4/1-1.4:1.0/0003:17EF:600E.029A/input/input665
[38565.755949] hid-generic 0003:17EF:600E.029A: input,hidraw1: USB HID v1.11 Mouse [Lenovo Optical Mouse] on usb-0000:01:00.0-1.4/input0
[38619.360692] usb 1-1.4: USB disconnect, device number 48
[38620.864990] usb 1-1.4: new low-speed USB device number 49 using xhci_hcd
[38620.984011] usb 1-1.4: New USB device found, idVendor=17ef,idProduct=600e, bcdDevice= 1.00
[38620.998117] usb 1-1.4: New USB device strings: Mfr=0, Product=2,SerialNumber=0
This adds HID_QUIRK_ALWAYS_POLL for this device in order to work properly.
Signed-off-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add support to hid-lg-g15 for the Logitech Z-10 speakers. This adds
support for the LCD menu keys found on these speakers, as well as
support for controlling the LCD's brightness through a LED classdev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This mouse has a horizontal wheel that requires special handling.
Without this patch, the horizontal wheel acts like a vertical wheel.
In the output of `hidrd-convert` for this mouse, there is a
`Usage (B8h)` field. It corresponds to a byte in packets sent by the
device that specifies which wheel generated an input event.
The name "A4TECH" is spelled in all capitals on the company website.
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Just like the K12A the Dell K15A keyboard-dock has problems with
get_feature requests. This sometimes leads to several
"failed to fetch feature 8" messages getting logged, after which the
touchpad may or may not work.
Just like the K15A these errors are triggered by undocking and docking
the tablet.
There also seem to be other problems when undocking and then docking again
in quick succession. It seems that in this case the keyboard-controller
still retains some power from capacitors and does not go through a
power-on-reset leaving it in a confuses state, symptoms of this are:
1. The USB-ids changing to 048d:8910
2. Failure to read the HID descriptors on the second (mouse) USB intf.
3. The touchpad freezing after a while
These problems can all be cleared by undocking the keyboard and waiting
a full minute before redocking it. Unfortunately there is nothing we can
do about this in the kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Saitek X65 joystick has a pair of axes that were used as mouse
pointer controls by the Windows driver. The corresponding usage page is
the Game Controls page, which is not recognized by the generic HID
driver, and therefore, both axes get mapped to ABS_MISC. The quirk makes
the second axis get mapped to ABS_MISC+1, and therefore made available
separately.
Signed-off-by: Nirenjan Krishnan <nirenjan@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
A number of USB keyboards, using the Semitek firmware, are capable of
handling arbitrary N-key rollover, but due to a buggy report
descriptor, keys beyond the sixth cannot be detected by the generic
HID driver.
There are numerous hardware variants sold by several vendors, mostly
using generic names like "GK61" for the 61-key version. These
keyboards are sometimes known collectively as the "GK6X" series.
The keyboard has three USB interfaces. Interface 0 uses the standard
HID boot protocol, limited to eight modifier keys and six normal keys;
interface 2 uses a custom report format that permits any number of
keys. If more than six keys are pressed simultaneously, the first six
are reported via interface 0 while subsequent keys are reported via
interface 2.
(Interface 1 uses a custom protocol for reprogramming the keyboard;
this can be controlled through userspace tools and is not of concern
for the present driver.)
The report descriptor for interface 2, however, is incorrect (for
report ID 0x04, the input field is marked as "array" rather than
"variable".) The descriptor appears to be correct in other respects,
so we simply replace the incorrect byte before parsing the descriptor.
Signed-off-by: Benjamin Moody <bmoody@member.fsf.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The FTDI FT260 chip implements USB to I2C/UART bridges through two
USB HID class interfaces. The first - for I2C, and the second for UART.
Each interface is independent, and the kernel detects it as a separate
USB hidraw device.
This commit adds I2C host adapter support.
Signed-off-by: Michael Zaidman <michael.zaidman@gmail.com>
Tested-by: Aaron Jones (FTDI-UK) <aaron.jones@ftdichip.com
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some new 2021 version of ASUS gamer laptops are using an updated
N-Key keyboard with the PID of 0x19b6. This version is using the
same init sequence and brightness control as the 0x1866 keyboard.
Signed-off-by: Luke D Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Plantronics Blackwire 3220 Series (047f:c056) sends HID reports twice
for each volume key press. This patch adds a quirk to hid-plantronics
for this product ID, which will ignore the second volume key press if
it happens within 5 ms from the last one that was handled.
The patch was tested on the mentioned model only, it shouldn't affect
other models, however, this quirk might be needed for them too.
Auto-repeat (when a key is held pressed) is not affected, because the
rate is about 3 times per second, which is far less frequent than once
in 5 ms.
Fixes: 81bb773fae ("HID: plantronics: Update to map volume up/down controls")
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Dinovo Edge and Dinovo Mini keyboards with builtin touchpad come with
a different version of the quad/bt2.0 combo receivers shipped with the
MX5000 and MX5500 keyboards. These receivers are compatible with one
another, e.g. the Dinovo Edge keyboard can be paired with the MX5000
receiver.
Like the MX5x00 receivers in HID proxy mode these receivers present
themselves as a hub with multiple USB-HID devices, one for the keyboard
and one for the mouse.
Where they differ is that the mouse USB-device has 2 input reports for
reporting mice events. It has the exact same INPUT(2) report as the
MX5x00 receivers, but it also has a second INPUT(5) mouse report which
is different; and when the Dinovo receivers are paired with the Dinovo
keyboards the second INPUT(5) mouse report is actually used for events
on the builtin touchpad.
Add support for handling the Dinovo quad/bluetooth-2.0 combo receivers
in HID proxy mode to logitech-dj, like we already do for the similar
MX5000 and MX5500 receivers.
This adds battery monitoring functionality (through logitech-hidpp) and
fixes the Phone (Fn + F1) and "[A]" - "[D]" (Fn + F9 - F12) hotkeys not
working on the Dinovo Edge.
Note these receivers present themselves as a hub with 2 separate USB
devices for the keyboard and mouse; and the logitech-dj code needs to
bind to both devices (just as with the MX5x00 receivers).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The logitech-dj code already uses hid-ids.h defines for almost all devices
it supports. Lets be consistent: add and use hid-ids.h defines for the
G700, MX5000 and MX5500 receivers too.
Also add / update some comments to make the comment style in the
hid_device_id table consistent too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Implement support for PlayStation DualSense gamepad in USB mode.
Support features include buttons and sticks, which adhere to the
Linux gamepad spec.
Signed-off-by: Roderick Colenbrander <roderick.colenbrander@sony.com>
Reviewed-by: Barnabás Pőcze <pobrn@protonmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Battery status is reported for the HP Spectre X360 Convertible 15-df0xxx
even if it does not have a battery. Prevent it to always report the
battery as low.
Signed-off-by: Elia Devito <eliadevito@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ITE8568 EC on the Voyo Winpad A15 presents itself as an I2C-HID
attached keyboard and mouse (which seems to never send any events).
This needs the I2C_HID_QUIRK_NO_IRQ_AFTER_RESET quirk, otherwise we get
the following errors:
[ 3688.770850] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3694.915865] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3701.059717] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3707.205944] i2c_hid i2c-ITE8568:00: failed to reset device.
[ 3708.227940] i2c_hid i2c-ITE8568:00: can't add hid device: -61
[ 3708.236518] i2c_hid: probe of i2c-ITE8568:00 failed with error -61
Which leads to a significant boot delay.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This commit adds support for tilt on Standard Guitar Hero PS3 Guitars, and GH3
PC Guitars, mapping it to ABS_RY.
Note that GH3 PC Guitars are identical, only they use different VID and PIDs.
Also note that vendor id 0x12ba is used by a variety of different rhythm
controllers on the ps3.
Signed-off-by: Sanjay Govind <sanjay.govind9@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some Chicony's keyboards support airplane mode hotkey (Fn+F2) with
"Wireless Radio Control" feature. For example, the wireless keyboard
[04f2:1236] shipped with ASUS all-in-one desktop.
After consulting Chicony for this hotkey, learned the device will send
with 0x11 as the report ID and 0x1 as the value when the key is pressed
down.
This patch maps the event as KEY_RFKILL.
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Battery status is being reported for the Elan touchscreen on ASUS
UX550 laptops despite not having a batter. It always shows either 0 or
1%.
Signed-off-by: Seth Miller <miller.seth@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make the hid-ite driver handle the Acer S1002 keyboard-dock, this
leads to 2 improvements:
1. The non working wifi-toggle hotkey now works.
2. Toggling the touchpad on of with the hotkey will no show OSD
notifications in e.g. GNOME3. The actual toggling is handled inside
the keyboard, this adds support for notifying evdev listeners about this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This commit adds support for the Guitar Hero Live PS3 and Wii U dongles.
These dongles require a "magic" USB control message [1] to be sent
approximately every 10 seconds otherwise the dongle will not report
events where the strumbar is hit while a fret is being held.
Also, inspired by a patch sent on linux-input by Sanjay Govind [2], the
accelerometer is mapped to ABS_RY for tilt.
Interestingly, the Wii U and PS3 dongles share the same VID and PID.
[1] https://github.com/ghlre/GHLtarUtility/
[2] https://marc.info/?l=linux-input&m=157242835928542&w=2
Signed-off-by: Pascal Giard <pascal.giard@etsmtl.ca>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Mayflash/Dragonrise seems to have yet another device ID for one of their
Gamecube controller adapters. Previous to this commit, the adapter
registered only one /dev/input/js* device, and all controller inputs (from
any controller) were mapped to this device. This patch defines the 1846
USB device ID and enables the HID_QUIRK_MULTI_INPUT quirk for it, which
fixes that (with the patch, four /dev/input/js* devices are created, one
for each of the four controller ports).
Signed-off-by: Ethan Warth <redyoshi49q@gmail.com>
Tested-by: Wladimir J. van der Laan <laanwj@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Enables three buttons (Fn1, Fn2, and Fn3) on the ELECOM M-XGL20DLBK
wireless mouse.
While this mouse is EX-G brand, report descriptor is a bit different
from EX-G trackball mouse. To enable extra buttons, report should be
rewritten in a similar way to trackballs, but with different position
parameters.
Signed-off-by: YOSHIOKA Takuma <lo48576@hard-wi.red>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The battery status is also being reported by the logitech-hidpp driver,
so ignore the standard HID battery status to avoid reporting the same
info twice.
Note the logitech-hidpp battery driver provides more info, such as properly
differentiating between charging and discharging. Also the standard HID
battery info seems to be wrong, reporting a capacity of just 26% after
fully charging the device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Kernel 5.4 introduces HID_QUIRK_INCREMENT_USAGE_ON_DUPLICATE, devices need to
be set explicitly with this flag.
Signed-off-by: Chris Ye <lzye@google.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ASUS N-Key keyboard uses the productId of 0x1866 and is used in
almost all modern ASUS gaming laptops with slight changes to the
firmware. This patch enables: Fn+key hotkeys, keyboard backlight
brightness control.
Additionally this keyboard requires the LED interface to be
initialized before such things as keyboard backlight control work.
Signed-off-by: Luke D Jones <luke@ljones.dev>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device needs HID_QUIRK_MULTI_INPUT in order to be presented to userspace
in a consistent way.
Reported-and-tested-by: David Gámiz Jiménez <david.gamiz@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
