Split TX tracing to be per TB. This is needed now that
AMSDUs can be sent and skb can be larger than trace
limit.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we TX AMSDU, we shouldn't pad the packet. In the past,
we were building AMSDU only in transport layer, and gen2
functions are built based on this. However, now that op mode
may build AMSDUs, we need to take care of padding also in
gen2 "non-pcie-amsdu" path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbua+lAAoJEG4XJFUm622bc74H/3CU3nKceottcybfmdNcxbTj
OHQ6ulu2OJvIrTnKOIe9WWcgoGeoEEKUcEvrV2SjopYUvFR+XPdC0TPKCxmzi020
QQyemogR+EyMx4nDqYkMysACQjTgzym8vKYrYZ5JAf0S12nRkeu4Qhvod6a9bHkO
HJWJekhm2+wIXOb02LoLhsdijhUUlYPcROZCAXlsYf7mpRIgf7PJQURI+yjfiGBW
Z8cGOH7QHU/68b5ExQAgD3OVpI7cTQ3JlE/IM1nM7UozDPRm7ZipW+Q5XJCYwjfU
Yexh1wo8CUSoK2FW5mwJJUaDUfWR5PQMDBjmGXuauFrfIrTIltJpWliEAIFV++c=
=gsaN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.
Major changes:
mt76
* more major refactoring to make it easier add new hardware support
* more work on mt76x0e support
* support for getting firmware version via ethtool
* add mt7650 PCI ID
iwlwifi
* HE radiotap cleanup and improvements
* reorder channel optimization for scans
* bump the FW API version
qtnfmac
* fixes for 'iw' output: rates for enabled SGI, 'dump station'
* expose more scan features to host: scan flush and dwell time
* inform cfg80211 when OBSS is not supported by firmware
wlcore
* add support for optional wakeirq
ath10k
* retrieve MAC address from system firmware if provided
* support extended board data download for dual-band QCA9984
* extended per sta tx statistics support via debugfs
* average ack rssi support for data frames
* speed up QCA6174 and QCA9377 firmware download using diag Copy
Engine
* HTT High Latency mode support needed by SDIO and USB support
* get STA power save state via debugfs
ath9k
* add reset functionality for airtime station debugfs file
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.
Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.
The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_txq_build_tfd() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The fall-through to the MVM case is intended as we have to do
*something* to continue, and can't easily clean up. So we'll
just fail in mvm later, if this does happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we use the iwl_pcie_gen2_set_tb() return value for BIT(),
we should validate that it's not going to be negative, so do
the check and bail out if we hit an error. We shouldn't, as
we check if it'll fit beforehand, but better be safe.
Fixes: ab6c644539 ("iwlwifi: pcie: copy TX functions to new transport")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With NICs that don't read the NVM directly and instead rely on getting
the relevant data from the firmware, the number of reserved MAC
addresses was not added to the API. This caused the driver to assume
there is only one address which results in all interfaces getting the
same address. Update the API to fix this.
While at it, fix-up the comments with firmware api names to actually
match what we have in the firmware.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If all free RB queues are empty, the driver will never restock the
free RB queue. That's because the restocking happens in the Rx flow,
and if the free queue is empty there will be no Rx.
Although there's a background worker (a.k.a. allocator) allocating
memory for RBs so that the Rx handler can restock them, the worker may
run only after the free queue has become empty (and then it is too
late for restocking as explained above).
There is a solution for that called 'emergency': If the number of used
RB's reaches half the amount of all RB's, the Rx handler will not wait
for the allocator but immediately allocate memory for the used RB's
and restock the free queue.
But, since the used RB's is per queue, it may happen that the used
RB's are spread between the queues such that the emergency check will
fail for each of the queues
(and still run out of RBs, causing the above symptom).
To fix it, move to emergency mode if the sum of *all* used RBs (for
all Rx queues) reaches half the amount of all RB's
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In mac80211, the default remains for HT, so set the limit to
HE for our driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For SU/SU-ER/MU PPDUs we have spatial reuse.
For those where it's relevant we also know the pre-FEC
padding factor, PE disambiguity bit, beam change bit
and doppler bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add information about the LDCP extra symbol segment to the HE
data when applicable (not for trigger-based PPDUs).
While at it, clean up the code for UL/DL a bit.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This code gets shorter if it doesn't have to check all the
conditions, so move it to an appropriate place that has all
of them validated already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split the code out into a separate routine, and move that to be
called inside the previously introduced iwl_mvm_decode_he_phy_data()
function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull some of the decoding of he_phy_data into a separate function so
we don't need to check over and over again if it's valid.
While at it, fix the UL/DL bit reporting to be for all but trigger-
based frames.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As detected by Luca during code review when I move this in the
next patch, the code here is putting the data into the wrong
field (flags1 instead of flags2). Fix that.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Reported-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove a stray empty line, unbreak some lines that aren't
really that long, and move on variable setting into the
initializer to avoid initializing it twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is equivalent to checking he_phy_data != HE_PHY_DATA_INVAL,
which is already done in a number of places, so remove the extra
'overload' variable entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
queue which means that the worker will not run for now
since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
and that we are now resuming from suspend and cancels
the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
and doesn't really allocate a station ID for the aux
station
17) a new queue is added for the aux station
Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.
Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:
drivers/net/wireless/intel/iwlwifi/pcie/trans.c:2122 iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]()
Timeout waiting for hardware access (CSR_GP_CNTRL 0x080403d8)
Call Trace:
[<ffffffffc03e6ad3>] iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]
[<ffffffffc03e6a13>] iwl_trans_pcie_dump_regs+0x3fd/0x3fd [iwlwifi]
[<ffffffffc03dad42>] iwl_fw_error_dump+0x4f5/0xe8b [iwlwifi]
[<ffffffffc04bd43e>] __iwl_mvm_mac_start+0x5a/0x21a [iwlmvm]
[<ffffffffc04bd6d2>] iwl_mvm_mac_start+0xd4/0x103 [iwlmvm]
[<ffffffffc042d378>] drv_start+0xa1/0xc5 [iwl7000_mac80211]
[<ffffffffc045a339>] ieee80211_reconfig+0x145/0xf50 [mac80211]
[<ffffffffc044788b>] ieee80211_resume+0x62/0x66 [mac80211]
[<ffffffffc0366c5b>] wiphy_resume+0xa9/0xc6 [cfg80211]
The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:
0x00002093 | ADVANCED_SYSASSERT
0x000002F0 | trm_hw_status0
0x00000000 | trm_hw_status1
0x00000B38 | branchlink2
0x0001978C | interruptlink1
0x00000000 | interruptlink2
0xFF080501 | data1
0xDEADBEEF | data2
0xDEADBEEF | data3
Firmware error during reconfiguration - reprobe!
FW error in SYNC CMD SCD_QUEUE_CFG
Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.
Fixes: bf8b286f86 ("iwlwifi: mvm: defer setting IWL_MVM_STATUS_IN_HW_RESTART")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself. Group them in a function to avoid code duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The code that dumps various memory types repeats itself. Move it to a
function to avoid duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow the FW to reorder HB channels and first scan HB channels with
assumed APs, in order to reduce the scan duration.
Currently enable it for all scan requests types.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split iwl_fw_error_dump to two parts. The first part will dump the
actual data, and second will do the file allocations, trans calls and
actual file operations. This is done in order to enable reuse of the
code for the new debug ini infrastructure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a macro to replace all the conditions checking for valid dump
length. In addition, move the fifo len calculation to a helper
function.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The debug variables are bloating the iwl_fw struct. And the fields
are out of order, missing docs and some are redundant.
Clean this up. This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When reading the profiles from the EWRD table in ACPI, we loop over
the data and set it into our internal table. We use the number of
profiles specified in ACPI without checking its validity, so if the
ACPI table is corrupted and the number is larger than our array size,
we will try to make an out-of-bounds access.
Fix this by making sure the value specified in the ACPI table is
valid.
Fixes: 6996490501 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Minor conflict in net/core/rtnetlink.c, David Ahern's bug fix in 'net'
overlapped the renaming of a netlink attribute in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbsgclAAoJEG4XJFUm622bAJ0H/A53eluDpiA6cT2tbThQn/jC
+t9DH6EMR4WpYaBEFZtfbZxgrow2bdbllrfrcq22U8Z9BTg875MunJAureEG8Rkn
mBowkuu/RESOO00JXTuqvGcTP+1oaaETEdyABzQFI3uCDyEF9vGCJwNODtyQ5Rch
JYFVDJhWYm1K84jTCDX1x9izEKxf1PaQobh8JqZnvNG0QOIDpT6y/T5RGhUL9nTr
aRuGDa9ap4RFocq1t0eVqx/NliXOHuEbO58E6rMm9DiSujmf1Wa/tndNXGxGWk/N
X8KCz619Syr3v/lF6gXWwmsHt5TBh+peKajUsVY9wJUYkBFTOzVjy0ucYCr67yA=
=HZJ3
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2018-10-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.19
First, and also hopefully the last, set of fixes for 4.19. All small
but still important fixes
mt76x0
* fix a bug when a virtual interface is removed multiple times
b43
* fix DMA error related regression with proprietary firmware
iwlwifi
* fix an oops which was a regression in v4.19-rc1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbs6LVAAoJEG4XJFUm622b0sAH/1WLU433ZipgULs6PLULDz3/
cFS4CSu9+Hewx9MKvdr+vgMoru70CkiFIZMJeo/oNqAtFb6TQhXPFz2Ci3K4Y6jK
yZKATh9PvzQrOGQ1iy4p8QK6bQ9WRUNY5+elJuNQH62oB/SZ0XqCMU8ujUQRSaTC
xVqfIRnAtKcchAm/nqxx+EwlGCiUmlyt2pw2IUXXABLW7Fkj3Z3ISlOd8xVW6tca
XyWlx9pjZOrFrgOzyORB/B4TNI5q5CdcYPg2DEpqOs6LQeGXEq4BSxfxCe2de4ku
St6417K0OFTbUTZS7kJaxJnQFd1ZWhDtj5cJUzdNsSVzqeYeJoTnR4FBqDWLlec=
=7Nmq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-10-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.20
First set of new features for 4.20. mt76 driver is going through major
refactoring and that's why there are so many mt76 patches. iwlwifi is
also under heavy development and smaller changes to other drivers.
Also wireless-drivers was merged to fix a conflict between the two trees.
Major changes:
ath10k
* limit available channels via DT ieee80211-freq-limit
wil6210
* add 802.11r Fast Roaming support for AP and station modes
* add support for channel 4
iwlwifi
* new FW API handling
* some improvements in the PCI recovery mechanism
* enable a new scanning feature;
* continued work on HE (mostly radiotap)
* TKIP implementation in new devices
* work continues for new 22560 hardware
mt76
* add support for Alfa AWUS036ACM
* lots of refactoring to make it easier to add new hardware support
* prepare for adding mt76x0e (pci-e variant) support
* add CONFIG_MT76x0E kconfig symbol
brcmfmac
* add support CYW89342 mini-PCIe device
* add 4-way handshake offload detection for FT-802.1X
* enable NL80211_EXT_FEATURE_CQM_RSSI_LIST
* fix for proper support of 160MHz bandwidth
rtl8xxxu
* add rtl8188ctv support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
-----BEGIN PGP SIGNATURE-----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=5Y2V
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2018-09-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Second set of iwlwifi patches for 4.20
* TKIP implementation in new devices;
* Fix for the shared antenna setting in 22000 series;
* Report that we set the RU offset in HE code;
* Fix some register addresses in 22000 series;
* Fix one FW feature TLV that had a conflict with another value;
* A couple of fixes for SoftAP mode;
* Work continues for new 22560 hardware;
* Some fixes in the datapath;
* Some debugging and other general fixes;
* Some cleanups, small improvements and other general fixes;
Clang warns when multiple pairs of parentheses are used for a single
conditional statement.
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: warning: equality
comparison with extraneous parentheses [-Wparentheses-equality]
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: remove
extraneous parentheses around the comparison to silence this warning
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
~ ^ ~
drivers/net/wireless/intel/ipw2x00/ipw2200.c:5655:28: note: use '=' to
turn this equality comparison into an assignment
if ((priv->ieee->iw_mode == IW_MODE_ADHOC)) {
^~
=
1 warning generated.
Link: https://github.com/ClangBuiltLinux/linux/issues/134
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Support for setting keys for TKIP cipher suite was mistakenly removed
for AP mode. Fix this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The capability bit was added to the driver and had been negotiated
with the firmware, but then got forgotten in the firmware and later
reused for a different capability. Now the firmware added it in a
new bit.
Fixes: 2eabc84d2f ("iwlwifi: mvm: only send LEDS_CMD when the FW supports it")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As a temporary stage in the 22560 devices bring up, we disabled
power save, to avoid bugs related to that domain.
Now we would like to use power save so enable the balanced mode,
and allow configuring the mode via module parameter.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In future devices we will have more than one debug buffer.
Prepare the infrastructure for allocation and release of
multiple debug buffers by grouping the variables in an array
of structures and moving it to trans section, where they will
be visible to opmode and FW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to be able to build A-MSDUs in higher layers, e.g. by
xmit_more, so support transmitting SKBs with fraglist to use
it for such.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We no longer want to consider the RSSI if the beacon / probe
has been heard on an adjacent channel.
This was based on a firmware capability that is now
unavailable.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires setting the non-shared antenna
for the single_stream_ant_msk field in the TLC command.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When operating as a soft ap with wep security, the key was not
configured to the fw for the stations, based on the fact that the
key will be specified in the tx command.
However, in the new tx api the tx command does not include the key,
which resulted in all data frames going out un-encrypted.
Fix it by configuring the key for all the stations as they are added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current FIFO size calculation is wrong for two reasons:
- We access lmac 0 by default
- We don't take 11ax into consideration.
Fix both.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
RB size can be configured by user to be greater than 4K.
That's needed for monitor to capture big AMSDUs.
The firmware now enables different RB sizes configuration
via context info.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since AMSDUs are not de-aggregated by HW in monitor mode,
we still need the option for setting large RBs (up to 12K).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Today, the length of a debug message in iwl_trans_pcie_reclaim
may pass the MAX_MSG_LEN, which is 110.
An example for this kind of message is:
'iwl_trans_pcie_reclaim: Read index for DMA queue txq id (2),
last_to_free 65535 is out of range [0-65536] 2 2.'
Cut the message a bit so it will fit the allowed MAX_MSG_LEN.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the HW is not responding at probe time, fail immediately complaining
about it. Without this, we see that the kernel spends > 100ms trying to
load firmware (even gives an incorrect impression that it actually
loaded a firmware) and do unnecesary processing before concluding that
the device is not accessible:
INFO kernel: [ 34.092678] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
WARNING kernel: [ 34.093560] iwlwifi 0000:01:00.0: Direct firmware load for iwl-dbg-cfg.ini failed with error -2
INFO kernel: [ 34.111523] iwlwifi 0000:01:00.0: loaded firmware version 17.318154.0 op_mode iwlmvm
INFO kernel: [ 34.173250] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0xFFFFFFFF
ERR kernel: [ 34.198023] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
ERR kernel: [ 34.198044] iwlwifi 0000:01:00.0: iwlwifi device config registers:
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will allow us to reuse the function later for adding fraglist
SKBs to the TFD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When anything fails, we unmap the whole TFD in three different
places scattered throughout the code. Unify this to a single
place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the incoming frame should be an A-MSDU, it may already be one,
for example in the case of NAN multicast being encapsulated in an
A-MSDU. Thus, use the GSO algorithm to build A-MSDU only if the
skb actually contains GSO data.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the skb fragment loop into a helper routine to be able
to reuse it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Annotate the compressed BA notification array sizes and
make both of them 0-length since the length of 1 is just
confusing - it may be different than that and the offset
to the second one needs to be calculated in the C code
anyhow.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make the adjustments for gen2 TX and RX of TKIP packets. Strip MIC on
RX. Don't add IV space and keep the MIC space zeroed on TX.
Devices that support gen2 data path support TKIP only in station mode.
In all other modes, fall back to SW encryption. Do this early in the
set_key() callback so that the key flags would not be incorrectly set.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For newer devices we have higher range of periphery
addresses. Currently it is masked out, so we end up
reading another address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CDB support has nothing to do with non unified image.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The non-shared antenna was wrong for 22000 device series.
Fix it to ANT_B for correct antenna preference by coex in MVM driver.
Fixes: e34d975e40 ("iwlwifi: Add a000 HW family support")
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can dump data from the firmware either when it crashes,
or when the firmware is alive.
Not all the data is available if the firmware is running
(like the Tx / Rx FIFOs which are available only when the
firmware is halted), so we first check that the firmware
is alive to compute the required size for the dump and then
fill the buffer with the data.
When we allocate the buffer, we test the STATUS_FW_ERROR
bit to check if the firmware is alive or not. This bit
can be changed during the course of the dump since it is
modified in the interrupt handler.
We hit a case where we allocate the buffer while the
firmware is sill working, and while we start to fill the
buffer, the firmware crashes. Then we test STATUS_FW_ERROR
again and decide to fill the buffer with data like the
FIFOs even if no room was allocated for this data in the
buffer. This means that we overflow the buffer that was
allocated leading to memory corruption.
To fix this, test the STATUS_FW_ERROR bit only once and
rely on local variables to check if we should dump fifos
or other firmware components.
Fixes: 04fd2c2822 ("iwlwifi: mvm: add rxf and txf to dump data")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.
Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We already report the RU offset, so we'd better also
report that we know the value.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Check the actual bit (mask) in Rx notification rate_n_flags.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cleanup of the debug flow by moving several flows to separate
functions to increase readability. Three functions were created:
1. iwl_fw_get_prph_len - returns the size needed for periphery dump.
2. iwl_fw_dump_mem for - executes the memory dumping flow.
3. iwl_trans_get_fw_monitor_len - returns the size needed for monitor dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no value in having an anonymous struct for holding
a few fields, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The SP length in the ADD_STA command is an actual number of
frames, and not the SP len as it appears in the WME IE.
Fix that comment. The actual code is fine.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
.max_tfd_queue_size was ommited for 1000 card serries leading to oops in
swiotlb.
Fixes: 7b3e42ea2e ("iwlwifi: support multiple tfd queue max sizes for different devices")
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Align to new 11ax draft D3.0. Change/add new MAC and PHY capabilities
and update drivers' 11ax capabilities and mac80211's debugfs
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
-----BEGIN PGP SIGNATURE-----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=lLBA
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-09-03' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Here are quite a large number of fixes, notably:
* various A-MSDU building fixes (currently only affects mt76)
* syzkaller & spectre fixes in hwsim
* TXQ vs. teardown fix that was causing crashes
* embed WMM info in reg rule, bad code here had been causing crashes
* one compilation issue with fix from Arnd (rfkill-gpio includes)
* fixes for a race and bad data during/after channel switch
* nl80211: a validation fix, attribute type & unit fixes
along with other small fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The devices with PCI device ID 0x34F0 are part of the SoC and can be
combined with some different external RF modules. The configuration
for these devices should reflect that, but are currently mixed up. To
avoid confusion with discrete devices, add part of the firmware to be
used and the official name of the device to the cfg structs.
This is least reorganization possible (without messing things even
more) that could be done as a bugfix for this SoC. Further
reorganization of this code will be done separately.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts the addition of memory type in the memory debug TLV
as the firmware never ended up implementing it, and now the PRPH
dump is added as a different TLV.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of fragmented scan on the HB channels, configure EBS to be
fragmented as well.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support more txq_alloc command types by moving the command declaration
to the gen specific area. While at it, move some of the code segments
to a common place for re-use.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Decode the HE TB PPDU data that we get in sniffer mode
and use it to populate the HE radiotap information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add flags to the tlc_cfg_cmd for signaling peer support for receiving
Dual Carrier Modulation at BPSK (MCS 0), and set them according to peer
capabilities.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the HE phy capabilities IE there are 2 bits to signal support for
STBC in bandwidths of 80Mhz or less, and of 160Mhz.
Use these bits to determine STBC support if this IE exists.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make all FW debug data stop recording flows to use
iwl_fw_dbg_stop_recording function instead of writing to FW
registers directly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow access to the memory by the host and the device simultaneously.
This will be needed in some future patches.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As with the non-offloaded rs case, during assoc on the ap side the phy
context is set to 20MHz until authorization of a client that supports
wider channel-widths. Support this by sending the initial
tlc_config_cmd with max supported channel width of 20MHz until
authorization succeeds.
Fixes: 6b7a5aea71 ("iwlwifi: mvm: always init rs with 20mhz bandwidth rates")
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Probe responses were sent to the multicast station while
they should be routed to the broadcast station.
This has no negative effect since the frame was still
routed to the right queue, but it looked very fishy
to send a frame to a (queue, station) tuple where
'queue' is not mapped to 'station'.
Fixes: 7c305de2b9 ("iwlwifi: mvm: Direct multicast frames to the correct station")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the new method of parsing the NVM the disable_11n module parameter
isn't consulted when setting up HT capabilities. Fix this.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the bandwidth is only 20 MHz, then the second channel doesn't
exist, but the hardware reports the CRC was OK. Suppress the data
of the second channel in the HE radiotap in this case, by marking
it as not known.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is the same as for SU PPDUs, so it's easy to do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GI duration depends on the frame type in some cases,
take that into account when decoding for radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
I evidently completely confused "number of LTF symbols" and "LTF size".
Radiotap was reporting the former, while I thought it was the latter,
and we really need both.
Add the LTF symbol size into the newly defined field in radiotap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement the extended HE-MU info type decoding to show the HE-SIG-B
common contents in the HE-MU radiotap field.
The DW4 data is partially overwritten by the hardware in all cases, so
only the higher 16 bits can be used. To be able to use it for the HE
SIG-B common data anyway, move the bits around in the following way:
SIG-B common 0: DW 4 -> DW 7
SIG-B common 1: DW 7 -> DW 8
SIG-B common 2: DW 8 -> DW 4 (upper half)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We offloaded all the RX configuration of init to firmware. However,
the configuration of interrupt coalescing was left hanging - it wasn't
offloaded nor was it written by host.
This write to the CSR is allowed in gen2, so the host can do it.
Without it we have various issues with RX fullness.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The parameter that indicated whether the LQ command should be sent
as sync or async was removed, causing the LQ command to be sent as
sync from interrupt context (e.g. from the RX path). This resulted
in a kernel warning: "scheduling while atomic" and failing to send
the LQ command, which ultimately leads to a queue hang.
Fix it by adding back the required parameter to send the command as
sync only when it is allowed.
Fixes: d94c5a820d ("iwlwifi: mvm: open BA session only when sta is authorized")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we receive TX response, we may release a few packets
due to a hole that was closed in the transmission window.
However, if that frame failed, we will mark all the released
frames as failed and will send multiple BARs.
This affects statistics badly, and cause unnecessary frames
transmission.
Instead, mark all the following packets as success, with the
desired result of sending a bar for the failed frame only.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a bug in FW where the sequence control may be
incorrect, and the driver overrides it with the value
of the ieee80211 header.
However, in BAR there is no sequence control in the header,
which result with arbitrary sequence.
This access to an unknown location is bad and it makes the
logs very confusing - so fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the NIC is disconnected, we just can't do anything
besides seeking for help from the bus driver. Dumping the
device's memory is not necessary and just bloats the logs
with unusable data. Moreover, asking mac80211 to restart
the hardware is also useless. Bypass all this.
Also, use the STATUS_TRANS_DEAD status bit instead of a
bool inside the transport layer. The advantage of this is
that now, the transport and the op_mode can know what is the
situation and bypass the useless recovery steps mentioned
above.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new coex schema requires moving to SISO only when BT AG is 4.
Adjust the SISO criteria according to the coex schema version reported
by firmware.
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the NIC is disconnected from PCI bus, we are not
able to access it anymore. Check the status to avoid
some unnecessary work so can improve the performance.
It will help to make PCI bus rescan to bring back the
device much faster.
The real test is able to improve 7 seconds.
[w/o patch] It takes around 9 seconds
..
2018-04-20T01:22:39.691929-07:00 WARNING kernel:
[ 66.335881] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:22:48.101094-07:00 INFO kernel:
[ 74.747364] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
[w/a patch] It takes about 2 seconds.
..
2018-04-20T01:18:16.454087-07:00 WARNING kernel:
[ 75.966860] Timeout waiting for hardware access (CSR_GP_CNTRL 0xffffffff)
..
2018-04-20T01:18:18.602717-07:00 INFO kernel:
[ 78.116132] iwlwifi 0000:01:00.0: loaded firmware version 29.610311.0 op_mode iwlmvm
..
Fixes: 49564a806f ("iwlwifi: pcie: remove non-responsive device")
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no point in warning here, the user will just get an
error back to the debugfs file write, and warning just makes
it seem like there's an internal consistency problem when in
reality the user just happened to hit this at a bad time.
Remove the warning.
Fixes: f45f979dc2 ("iwlwifi: mvm: disable dbg data collect when fw isn't alive")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Every rx mpdu cmd is built from cmd_hdr | 80211_hdr. The problem is
that the size of cmd_hdr changes with API changes and we don't know
where the 80211_hdr starts.
By adding the size of cmd_hdr dynamically, we can ensure that we always
know how to parse mpdu frames, without dependending on the API changes.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will allow using the same init in future generations.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Store the default rxq number in a variable, so we won't need
to use the actual number in the code.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update reduce tx power command API to be compatible with new FW API.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While associated in low latency mode, or when traffic load is high,
don't enable EBS in scan request if fragmented EBS is not supported
by the FW.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation's address shouldn't be in the license
notice anymore, and some of our check scripts complain about it
(via checkpatch.pl). Remove the address to silence it.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is used only within PCIe, and there's no reason to go through
the transport methods for a function call within PCIe itself.
Remove the dump_regs() method and call the function directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow other device generations to use the utilities that
are used to send and reclaim host commands and to allocate
rx, by making it non-static.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We would like to allow using tx init code for other queues but
the command queue - for newer devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We need to drop packets with errors (such as replay,
MIC, ICV, conversion, duplicate and so on).
Drop invalid packets, put the status bits in the metadata and
move the enum definition to the correct place (FW API header).
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The user can validate what was written to the file by reading it,
and check what is the default value before changing it.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The HE code is bloating the RX handling, and makes it too big.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Current implementation turns this bit on only for HE MU.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some variables are used in iwl-fh.h, but their type's definition
isn't included. This may break compilation when using the file
without including the necessary dependencies first.
Add the required include to iwl-fh.h.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A probe response built by a P2P GO should contain:
1. CSA/eCSA IE when relevant
2. If the corresponding probe request had P2P IE, then
need to add P2P IE with NOA attributes.
However, the NOA attributes and the updated channel switch
counter are known only to the FW. The solution is that FW
will send a notification with the relevant probe response
data and the driver will save it and update the probe
response accordingly.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A new FW API has been added for WOWLAN_GET_STATUSES to support
multiple GTK keys and IGTK keys. Check the respective TLV and use the
new API when it is set.
Let most of the code use the new version (v7) and convert the old
version (v6) to the new one when needed.
Also refactor some functions a bit so that they can be reused more
easily. Particularly the part that calls WOWLAN_GET_STATUSES which is
reused in D3 and D0i3.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Runtime PM can only be used if CONFIG_PM is set. Move all the d0i3
code (which is essentially runtime PM) behind the CONFIG_PM flag.
This prevents undefined usage of some functions when CONFIG_PM is not
defined.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We repeated the same if twice in a row. Remove the second one and
move the code block into the previous one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During d3, the firmware records debug data into internal buffer
if debug data collection occurs, collect the data that was written to the
buffer
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The tid for Non-QOS frames is set to IWL_MAX_TID_COUNT. This value
is also used for configuring the queue for non-QOS data. However, this
tid is used by the FW for management queues. As a result, the FW
does not encrypt non-QOS data frames.
Fix this by setting the tid for non-QOS data frames to zero, which
is a valid value for data frames in the FW.
This also fixes a bug in sending multicast frames, where the queues
are allocated with tid == 0, but are sent with tid == 8, which may
lead to unexpected behavior.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Upon first calling read() on a debugfs file, invoke
iwl_dbgfs_##name##_read and store the response buffer on the heap, so
subsequent read() calls don't need to invoke said function again.
This is done because cat etc will call read() repeatedly until EOF is
reached (or read() returns 0), which in the current implementation will
cause said function to be invoked multiple times.
With the current implementation this can also cause buggy behavior in
some weird edge cases where the first invocation returns a string of
length n, and the second of length m>n: The last m-n characters of
the second invocation will be printed to screen.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_dhc_tlc_cmd struct is not used, so remove it, including the
iwl_tcl_debug_flags enumeration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Don't enable debugging timestamps by default, so we save power by not
waking up the FW with timestamp commands.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make wmm_rule be part of the reg_rule structure. This simplifies the
code a lot at the cost of having bigger memory usage. However in most
cases we have only few reg_rule's and when we do have many like in
iwlwifi we do not save memory as it allocates a separate wmm_rule for
each channel anyway.
This also fixes a bug reported in various places where somewhere the
pointers were corrupted and we ended up doing a null-dereference.
Fixes: 230ebaa189 ("cfg80211: read wmm rules from regulatory database")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
[rephrase commit message slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----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=2Dmn
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
- Decode AER errors with names similar to "lspci" (Tyler Baicar)
- Expose AER statistics in sysfs (Rajat Jain)
- Clear AER status bits selectively based on the type of recovery (Oza
Pawandeep)
- Honor "pcie_ports=native" even if HEST sets FIRMWARE_FIRST (Alexandru
Gagniuc)
- Don't clear AER status bits if we're using the "Firmware-First"
strategy where firmware owns the registers (Alexandru Gagniuc)
- Use sysfs_match_string() to simplify ASPM sysfs parsing (Andy
Shevchenko)
- Remove unnecessary includes of <linux/pci-aspm.h> (Bjorn Helgaas)
- Defer DPC event handling to work queue (Keith Busch)
- Use threaded IRQ for DPC bottom half (Keith Busch)
- Print AER status while handling DPC events (Keith Busch)
- Work around IDT switch ACS Source Validation erratum (James
Puthukattukaran)
- Emit diagnostics for all cases of PCIe Link downtraining (Links
operating slower than they're capable of) (Alexandru Gagniuc)
- Skip VFs when configuring Max Payload Size (Myron Stowe)
- Reduce Root Port Max Payload Size if necessary when hot-adding a
device below it (Myron Stowe)
- Simplify SHPC existence/permission checks (Bjorn Helgaas)
- Remove hotplug sample skeleton driver (Lukas Wunner)
- Convert pciehp to threaded IRQ handling (Lukas Wunner)
- Improve pciehp tolerance of missed events and initially unstable
links (Lukas Wunner)
- Clear spurious pciehp events on resume (Lukas Wunner)
- Add pciehp runtime PM support, including for Thunderbolt controllers
(Lukas Wunner)
- Support interrupts from pciehp bridges in D3hot (Lukas Wunner)
- Mark fall-through switch cases before enabling -Wimplicit-fallthrough
(Gustavo A. R. Silva)
- Move DMA-debug PCI init from arch code to PCI core (Christoph
Hellwig)
- Fix pci_request_irq() usage of IRQF_ONESHOT when no handler is
supplied (Heiner Kallweit)
- Unify PCI and DMA direction #defines (Shunyong Yang)
- Add PCI_DEVICE_DATA() macro (Andy Shevchenko)
- Check for VPD completion before checking for timeout (Bert Kenward)
- Limit Netronome NFP5000 config space size to work around erratum
(Jakub Kicinski)
- Set IRQCHIP_ONESHOT_SAFE for PCI MSI irqchips (Heiner Kallweit)
- Document ACPI description of PCI host bridges (Bjorn Helgaas)
- Add "pci=disable_acs_redir=" parameter to disable ACS redirection for
peer-to-peer DMA support (we don't have the peer-to-peer support yet;
this is just one piece) (Logan Gunthorpe)
- Clean up devm_of_pci_get_host_bridge_resources() resource allocation
(Jan Kiszka)
- Fixup resizable BARs after suspend/resume (Christian König)
- Make "pci=earlydump" generic (Sinan Kaya)
- Fix ROM BAR access routines to stay in bounds and check for signature
correctly (Rex Zhu)
- Add DMA alias quirk for Microsemi Switchtec NTB (Doug Meyer)
- Expand documentation for pci_add_dma_alias() (Logan Gunthorpe)
- To avoid bus errors, enable PASID only if entire path supports
End-End TLP prefixes (Sinan Kaya)
- Unify slot and bus reset functions and remove hotplug knowledge from
callers (Sinan Kaya)
- Add Function-Level Reset quirks for Intel and Samsung NVMe devices to
fix guest reboot issues (Alex Williamson)
- Add function 1 DMA alias quirk for Marvell 88SS9183 PCIe SSD
Controller (Bjorn Helgaas)
- Remove Xilinx AXI-PCIe host bridge arch dependency (Palmer Dabbelt)
- Remove Aardvark outbound window configuration (Evan Wang)
- Fix Aardvark bridge window sizing issue (Zachary Zhang)
- Convert Aardvark to use pci_host_probe() to reduce code duplication
(Thomas Petazzoni)
- Correct the Cadence cdns_pcie_writel() signature (Alan Douglas)
- Add Cadence support for optional generic PHYs (Alan Douglas)
- Add Cadence power management ops (Alan Douglas)
- Remove redundant variable from Cadence driver (Colin Ian King)
- Add Kirin MSI support (Xiaowei Song)
- Drop unnecessary root_bus_nr setting from exynos, imx6, keystone,
armada8k, artpec6, designware-plat, histb, qcom, spear13xx (Shawn
Guo)
- Move link notification settings from DesignWare core to individual
drivers (Gustavo Pimentel)
- Add endpoint library MSI-X interfaces (Gustavo Pimentel)
- Correct signature of endpoint library IRQ interfaces (Gustavo
Pimentel)
- Add DesignWare endpoint library MSI-X callbacks (Gustavo Pimentel)
- Add endpoint library MSI-X test support (Gustavo Pimentel)
- Remove unnecessary GFP_ATOMIC from Hyper-V "new child" allocation
(Jia-Ju Bai)
- Add more devices to Broadcom PAXC quirk (Ray Jui)
- Work around corrupted Broadcom PAXC config space to enable SMMU and
GICv3 ITS (Ray Jui)
- Disable MSI parsing to work around broken Broadcom PAXC logic in some
devices (Ray Jui)
- Hide unconfigured functions to work around a Broadcom PAXC defect
(Ray Jui)
- Lower iproc log level to reduce console output during boot (Ray Jui)
- Fix mobiveil iomem/phys_addr_t type usage (Lorenzo Pieralisi)
- Fix mobiveil missing include file (Lorenzo Pieralisi)
- Add mobiveil Kconfig/Makefile support (Lorenzo Pieralisi)
- Fix mvebu I/O space remapping issues (Thomas Petazzoni)
- Use generic pci_host_bridge in mvebu instead of ARM-specific API
(Thomas Petazzoni)
- Whitelist VMD devices with fast interrupt handlers to avoid sharing
vectors with slow handlers (Keith Busch)
* tag 'pci-v4.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (153 commits)
PCI/AER: Don't clear AER bits if error handling is Firmware-First
PCI: Limit config space size for Netronome NFP5000
PCI/MSI: Set IRQCHIP_ONESHOT_SAFE for PCI-MSI irqchips
PCI/VPD: Check for VPD access completion before checking for timeout
PCI: Add PCI_DEVICE_DATA() macro to fully describe device ID entry
PCI: Match Root Port's MPS to endpoint's MPSS as necessary
PCI: Skip MPS logic for Virtual Functions (VFs)
PCI: Add function 1 DMA alias quirk for Marvell 88SS9183
PCI: Check for PCIe Link downtraining
PCI: Add ACS Redirect disable quirk for Intel Sunrise Point
PCI: Add device-specific ACS Redirect disable infrastructure
PCI: Convert device-specific ACS quirks from NULL termination to ARRAY_SIZE
PCI: Add "pci=disable_acs_redir=" parameter for peer-to-peer support
PCI: Allow specifying devices using a base bus and path of devfns
PCI: Make specifying PCI devices in kernel parameters reusable
PCI: Hide ACS quirk declarations inside PCI core
PCI: Delay after FLR of Intel DC P3700 NVMe
PCI: Disable Samsung SM961/PM961 NVMe before FLR
PCI: Export pcie_has_flr()
PCI: mvebu: Drop bogus comment above mvebu_pcie_map_registers()
...
fix spelling mistake in rx stats text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This part of the iwlwifi driver doesn't need anything provided by
pci-aspm.h, so remove the unnecessary include of it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbZyxDAAoJEG4XJFUm622bq2AH/2yJAeOKb7Z25ezsvldaEDd3
cYS4TjLevXacDU5NdINtm1IRMct1ZldwUjrjgR2I/eLaSHhxyIdV4hb05etSN8qZ
yo86aa1gs+8rSEn/GVO8UjX8Bh4NM/tff+yzMKWiWJGe9DtBvswSUPxBOU91vS8K
WcCpvWh9SpmAPyZEDWsZnTK7AUc+X2T+Soit+pJmLm9P3RxkvMqQxG82eMGVnooO
5aNe0T9zYLB4aB8unCJqPSYSLVDJ55vnC8tFIjcEhNCF/745gyMD/CrcQ4zCxdN/
KF6WEDc/XePF5qrHvkzWA7HiR0Xs9pDt3KugkU0enZV+cba0kKaBq230sZ++1KM=
=BwxN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-08-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.19
This time a bigger pull request as we have two new Mediatek drivers
MT76x2u (CONFIG_MT76x2U) and MT76x0U (CONFIG_MT76x0U). Also iwlwifi got
support for the new IEEE 802.11ax standard, the successor for
802.11ac. And naturally smaller new features and bugfixes all over.
Major changes:
wcn36xx
* fix WEP in client mode
wil6210
* add support for Talyn-MB (Talyn ver 2.0) device
* add support for enhanced DMA firmware feature
iwlwifi
* implement 802.11ax D2.0
* support for the new 22560 device family
* new PCI IDs for 22000 and 22560
qtnfmac
* implement cfg80211 power management callback
* enable multiple SSIDs scan support
* qtnfmac: implement basic WoWLAN support
mt7601u
* fall back to software encryption for hw unsupported ciphers
* enable 802.11 Management Frame Protection (MFP)
mt76
* support setting RTS threshold
* add USB support
* add support for MT76x2u devices
* add support for MT76x0U devices
mwifiex
* allow user space to set all other IEs except WMM IE
rsi
* add firmware support for AP+BT dual mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is different enough to justify a split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We would like to allow other utlities to init msix and rx.
Put their declarations in a place accessible to other utilities.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If CONFIG_IPV6 is not enabled in the kernel, tcp.h is not included
implicitly from other header files, causing compilation errors. To
solve that, explicitly include it in tx-gen2.c.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There was a bunch of code to support gscan which has never been used.
Remove it all to cleanup and get rid of a lot of dead code.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Balanced power save mode isn't supported in the fw for 22560 devices
yet. Configure the power save mode to CAM until it gets implemented.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This reverts commit f2e66c8df0.
The firmware never implemented this, and they do not plan to.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The periphery can't be accessed before we set the
INIT_DONE bit which initializes the device.
A previous patch added a reconfiguration of the MSI-X
tables upon resume, but at that point in the flow,
INIT_DONE wasn't set. Since the reconfiguration of the
MSI-X tables require periphery access, it failed.
The difference between WoWLAN and without WoWLAN is that
in WoWLAN, iwl_trans_pcie_d3_suspend clears the INIT_DONE
without clearing the STATUS_DEVICE_ENABLED bit in the
software status. Because of that, the resume code thinks
that the device is enabled, but the INIT_DONE bit has been
cleared.
To fix this, don't reconfigure the MSI-X tables in case
WoWLAN is enabled. It will be done in
iwl_trans_pcie_d3_resume anyway.
Fixes: 52848a79b9 ("iwlwifi: pcie: reconfigure MSI-X HW on resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently multi-queue is disabled for 22000 devices.
This was since driver isn't supposed to write to prph
registers anymore, and FW needs to configure the RFH.
Now that FW added support for the API - use it and remove
the 22000 multi RX queue disablement.
Bump min API version to avoid compatibility issues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the firmware does not stop recording debugging data when
entering D3 and this causes trouble (e.g. sporadic wake ups).
Fix that by stopping dbg recording when suspending.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Reading and dumping memory areas takes time, and sometimes
dumping all of the areas isn't necessary.
Allow choosing the memory areas which should be dumped.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Op mode will need this data in order to feed FW with it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes code less indented and more readable.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This allows less "dummy" declarations and casting.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices use a new rx_mpdu_desc api.
Update the code to use the new api.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The rfh for 22560 devices has changed so it supports now
the same arch of using used and free lists, but different
structures to support the last.
Use the new structures, hw dependent, to manage the lists.
bd, the free list, uses the iwl_rx_transfer_desc,
in which the vid is stored in the structs' rbid
field, and the page address in the addr field.
used_bd, the used list, uses the iwl_rx_completion_desc
struct, in which the vid is stored in the structs' rbid
field.
rb_stts, the hw "write" pointer of rx is stored in a
__le16 array, in which each entry represents the write
pointer per queue.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
