If the VIN device is part of a group of VIN devices (all Gen3 boards)
there is no reason to only unregister the group notifier if the VIN that
registers the notifier is removed. The VIN that registers the notifier
is always the last VIN device to be bound, so keeping the notifier
around after any VIN is unbound creates an unbalanced state where no VIN
in the group is operational.
Fix this by unconditionally unregistering the notifier when any VIN
device is unbound. Unregistering the notifier will lead to unbound()
being called and all video devices exposed by any VIN instance to be
removed.
The lock was only needed to protect the check which VIN registers the
notifier and is no longer needed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
On MMP3, the camera block lives on a separate power island. We want to
turn it off if the CCIC is not in use to conserve power.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This simplifies things a bit and makes adding runtime PM a bit more
straightforward.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sole reason for this was so that it would be possible to get a
mmp_camera from a platform_device in suspend/resume/remove hooks, because
drvdata used to be used by the v4l core.
Since commit 95db3a60e0 ("[media] v4l: Add a media_device pointer to the
v4l2_device structure") it is no longer case and thus we can make things
a great deal simpler.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 95db3a60e0 ("[media] v4l: Add a media_device pointer
to the v4l2_device structure") the v4l core doesn't insist on using drvdata
itself. Therefore we can use it ourselves, making things somewhat simpler.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The following W=1 build warning is seen on a m68k:
drivers/media/platform/fsl-viu.c: At top level:
drivers/media/platform/fsl-viu.c:36: warning: "out_be32" redefined
36 | #define out_be32(v, a) iowrite32be(a, (void __iomem *)v)
|
In file included from ./arch/m68k/include/asm/io_mm.h:25,
from ./arch/m68k/include/asm/io.h:8,
from ./include/linux/io.h:13,
from ./include/linux/irq.h:20,
from ./include/asm-generic/hardirq.h:13,
from ./arch/m68k/include/generated/asm/hardirq.h:1,
from ./include/linux/hardirq.h:9,
from ./include/linux/interrupt.h:11,
from drivers/media/platform/fsl-viu.c:17:
./arch/m68k/include/asm/raw_io.h:32: note: this is the location of the previous definition
32 | #define out_be32(addr,l) (void)((*(__force volatile u32 *) (addr)) = (l))
Avoid the out_be32() and in_be32() redefinitions when building for CONFIG_M68K
in the same way we currently do for CONFIG_PPC and CONFIG_MICROBLAZE.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following coccinelle report:
drivers/media/platform/mtk-vcodec/vdec/vdec_vp9_if.c:963:6-31:
WARNING: Comparison to bool
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Fix the following coccinelle reports:
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:197:14-35:
WARNING: Comparison to bool
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:198:7-29:
WARNING: Comparison to bool
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:451:12-19:
WARNING: Comparison to bool
drivers/media/platform/mtk-vcodec/mtk_vcodec_dec.c:1159:6-15:
WARNING: Comparison to bool
By replacing (cond == true) with (cond) and (cond == false) with
(!cond)
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes the following coccinelle report:
drivers/media/platform/sunxi/sun8i-rotate/sun8i_rotate.c:751:2-9:
line 751 is redundant because platform_get_irq() already prints an error
By removing the useless call to dev_err()
Found using - Coccinelle (http://coccinelle.lip6.fr)
Signed-off-by: Daniel W. S. Almeida <dwlsalmeida@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add mtk jpeg encode v4l2 driver based on jpeg decode, because that jpeg
decode and encode have great similarities with function operation.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add varability which would be used between jpeg dec and enc to a match
data structure, it will make the code linear.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename existing functions/defines/variables with a _dec prefix and
without dec_ prefix to prepare for the addition of the jpeg encoder
feature.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename the files which are for decode feature. This is preparing
path since the jpeg enc patch will be added later.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the generic clk_bulk_* helpers to enable and disable clocks.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Call mtk_jpeg_try_fmt_mplane() to replace the original computation of
sizeimage and bytesperline, because that mtk_jpeg_try_fmt_mplane()
already did it.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Jpeg doesn't support colorspace conversion, so it shouldn't accept any
other colorspace in S_FMT.
Change the colorspace of jpeg to the fixed value.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The standard v4l2_pix_format_mplane structure contains width/height/
sizeimage/bytesperline, so use v4l2_pix_format_mplane to replace them.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete the unused ctx parameter.
Using mtk_jpeg_formats and num_formats parameters is more generic,
because that jpeg enc will also use it.
Delete the macro definition of MTK_JPEG_FMT_TYPE_OUTPUT and
MTK_JPEG_FMT_TYPE_CAPTURE, because that MTK_JPEG_FMT_FLAG_DEC_OUTPUT
and MTK_JPEG_FMT_FLAG_DEC_CAPTURE are enough.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The function of mtk_jpeg_adjust_fmt_mplane() equals
mtk_jpeg_g_fmt_vid_mplane(), so use mtk_jpeg_g_fmt_vid_mplane() to
replace it .
Delete the unused ctx parameter.
Using fourcc to distinguish between different formats is more generic,
because that jpeg enc will also use it.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The maximum width and height supported by JPEG dec is 65535, so change
them from 8192 to 65535.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
JPEG dec does't support setting a compose rectangle, so remove
mtk_jpeg_dec_s_selection().
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move MTK_JPEG_COMP_MAX definition to mtk_jpeg_core.h file, because it
is used by mtk_jpeg_core.c file.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use clamp() to replace mtk_jpeg_bound_align_image() and round() to
replace mtk_jpeg_align().
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Change register offset hex numerals from uppercase to lowercase.
Change data type of max/min width/height from integer to unsigned
integer.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete zeroing the reserved fields because that the core already
does it.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is no need to queue an empty buffer for signaling a last frame,
because all frames are separate from each other in JPEG.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There is a delayed work scheduled before starting the hardware and
canceled in the interrupt handler. If the delayed work is executed, it
resets the hardware and reports the failure to V4L2, so that the
execution can continue from next frames.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add v4l2_m2m_suspend() function call in mtk_jpeg_suspend() to make sure
that the current frame is processed completely before suspend.
Add v4l2_m2m_resume() function call in mtk_jpeg_resume() to unblock the
driver from scheduling next frame.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete the resetting hardware flow in suspend and resume function
because that resetting operation will be done in device_run().
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Call pm_runtime_get_sync() before starting a frame and then
pm_runtime_put() after completing it. This can save power for the time
between processing two frames.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver can be instantiated multiple times, e.g. for a decoder and
an encoder. Moreover, other drivers could coexist on the same system.
This makes the static video node number assignment pointless, so switch
to automatic assignment instead.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Delete platform_get_resource operation for irq.
Return actual value rather than EINVAL when fail to get and request
irq.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Let v4l2_ctrl_subscribe_event() do the job for other types except
V4L2_EVENT_SOURCE_CHANGE.
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Xia Jiang <xia.jiang@mediatek.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This is only needed for drivers that do not use vb2_fop_release().
Note that vb2_queue_release() is *not* the counterpart of vb2_queue_init()
as some drivers here seem to think.
Also use vb2_video_unregister_device() to automatically stop streaming
at unregister time for those drivers that set vdev->queue.
Note that sun4i-csi didn't unregister the video device at all. That's
now fixed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use vb2_video_unregister_device() to automatically stop streaming
at unregister time.
This avoids the use of vb2_queue_release() which should not be
called by drivers that set vdev->queue.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The Kconfig help text for VIDEO_MEDIATEK_VCODEC was referring to a
single module named mtk-vcodec, while this driver produces two modules
named mtk-vcodec-dec and mtk-vcodec-enc. Fix that.
Reported-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When compiled on 32-bit ARM, the CAL driver fails with the FIELD_PREP()
macro complaining that the mask is not constant. While all callers of
the inline cal_write_field() function pass a constant mask, the mask
parameter itself is a variable, which likely doesn't please the
compiler.
Fix it by replacing FIELD_PREP() with a manual implementation.
Fixes: 50797fb30b ("media: ti-vpe: cal: Turn reg_(read|write)_field() into inline functions")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reported-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add support to add OPP tables and perf voting on the OPP powerdomain.
This is needed so venus votes on the corresponding performance state
for the OPP powerdomain along with setting the core clock rate.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Post a successful pm_ops->core_get, an error in probe
should exit by doing a pm_ops->core_put which seems
to be missing. So fix it.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced. For other error
paths after this call, things are the same.
Fix this by adding pm_runtime_put_noidle() after 'err_runtime_disable'
label. But in this case, the error path after pm_runtime_put_sync()
will decrease PM usage counter twice. Thus add an extra
pm_runtime_get_noresume() in this path to balance PM counter.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the newly introduced get_mbus_config() subdevice pad operation to
retrieve the remote subdevice MIPI CSI-2 bus configuration and configure
the number of active data lanes accordingly.
In order to be able to call the remote subdevice operation cache the
index of the remote pad connected to the single CSI-2 input port.
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the PXA camera driver to use the new set_mbus_config pad operation.
For this platform the change is not only cosmetic, as the pxa driver is
currently the only driver in mainline to make use of the g_mbus_config
and s_mbus_config video operations.
The existing driver semantic is the following:
- Collect all supported mbus config flags from the remote end
- Match them with the supported PXA mbus configuration flags
- If the remote subdevice allows multiple options for for VSYNC, HSYNC
and PCLK polarity, use platform data requested settings
The semantic of the new get_mbus_config and set_mbus_config differs from
the corresponding video ops, particularly in the fact get_mbus_config
reports the current mbus configuration and not the set of supported
configuration options, with set_mbus_config always reporting the actual
mbus configuration applied to the remote subdevice.
Adapt the driver to perform the following
- Set the remote subdevice mbus configuration according to the PXA
platform data preferences.
- If the applied configuration differs from the requested one (i.e. the
remote subdevice does not allow changing one setting) make sure that
- The remote end does not claim for DATA_ACTIVE_LOW, which seems not
supported by the platform
- The bus mastering roles match
While at there remove a few checks performed on the media bus
configuration at get_format() time as they do not belong there.
Compile-tested only.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Including:
- Removal of the dev->archdata.iommu (or similar) pointers from
most architectures. Only Sparc is left, but this is private to
Sparc as their drivers don't use the IOMMU-API.
- ARM-SMMU Updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell
Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d Updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel
drivers into their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test
coverage)
-----BEGIN PGP SIGNATURE-----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=3O2Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Remove of the dev->archdata.iommu (or similar) pointers from most
architectures. Only Sparc is left, but this is private to Sparc as
their drivers don't use the IOMMU-API.
- ARM-SMMU updates from Will Deacon:
- Support for SMMU-500 implementation in Marvell Armada-AP806 SoC
- Support for SMMU-500 implementation in NVIDIA Tegra194 SoC
- DT compatible string updates
- Remove unused IOMMU_SYS_CACHE_ONLY flag
- Move ARM-SMMU drivers into their own subdirectory
- Intel VT-d updates from Lu Baolu:
- Misc tweaks and fixes for vSVA
- Report/response page request events
- Cleanups
- Move the Kconfig and Makefile bits for the AMD and Intel drivers into
their respective subdirectory.
- MT6779 IOMMU Support
- Support for new chipsets in the Renesas IOMMU driver
- Other misc cleanups and fixes (e.g. to improve compile test coverage)
* tag 'iommu-updates-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (77 commits)
iommu/amd: Move Kconfig and Makefile bits down into amd directory
iommu/vt-d: Move Kconfig and Makefile bits down into intel directory
iommu/arm-smmu: Move Arm SMMU drivers into their own subdirectory
iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu
iommu: Add gfp parameter to io_pgtable_ops->map()
iommu: Mark __iommu_map_sg() as static
iommu/vt-d: Rename intel-pasid.h to pasid.h
iommu/vt-d: Add page response ops support
iommu/vt-d: Report page request faults for guest SVA
iommu/vt-d: Add a helper to get svm and sdev for pasid
iommu/vt-d: Refactor device_to_iommu() helper
iommu/vt-d: Disable multiple GPASID-dev bind
iommu/vt-d: Warn on out-of-range invalidation address
iommu/vt-d: Fix devTLB flush for vSVA
iommu/vt-d: Handle non-page aligned address
iommu/vt-d: Fix PASID devTLB invalidation
iommu/vt-d: Remove global page support in devTLB flush
iommu/vt-d: Enforce PASID devTLB field mask
iommu: Make some functions static
iommu/amd: Remove double zero check
...
-----BEGIN PGP SIGNATURE-----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=SYqr
-----END PGP SIGNATURE-----
Merge tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Legacy soc_camera driver was removed from staging
- New I2C sensor related drivers: dw9768, ch7322, max9271, rdacm20
- TI vpe driver code was re-organized and had new features added
- Added Xilinx MIPI CSI-2 Rx Subsystem driver
- Added support for Infrared Toy and IR Droid devices
- Lots of random driver fixes, new features and cleanups
* tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (318 commits)
media: camss: fix memory leaks on error handling paths in probe
media: davinci: vpif_capture: fix potential double free
media: radio: remove redundant assignment to variable retval
media: allegro: fix potential null dereference on header
media: mtk-mdp: Fix a refcounting bug on error in init
media: allegro: fix an error pointer vs NULL check
media: meye: fix missing pm_mchip_mode field
media: cafe-driver: use generic power management
media: saa7164: use generic power management
media: v4l2-dev/ioctl: Fix document for VIDIOC_QUERYCAP
media: v4l2: Correct kernel-doc inconsistency
media: v4l2: Correct kernel-doc inconsistency
media: dvbdev.h: keep * together with the type
media: v4l2-subdev.h: keep * together with the type
media: videobuf2: Print videobuf2 buffer state by name
media: colorspaces-details.rst: fix V4L2_COLORSPACE_JPEG description
media: tw68: use generic power management
media: meye: use generic power management
media: cx88: use generic power management
media: cx25821: use generic power management
...
camss_probe() does not free camss on error handling paths. The patch
introduces an additional error label for this purpose. Besides, it
removes call of v4l2_async_notifier_cleanup() from
camss_of_parse_ports() since its caller, camss_probe(), cleans up all
its resources itself.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Co-developed-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In case of errors vpif_probe_complete() releases memory for vpif_obj.sd
and unregisters the V4L2 device. But then this is done again by
vpif_probe() itself. The patch removes the cleaning from
vpif_probe_complete().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
We need to call of_node_put(comp->dev_node); on the error paths in this
function.
Fixes: c8eb2d7e82 ("[media] media: Add Mediatek MDP Driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state() and pci_enable/disable_device() to do required
operations. In generic mode, they are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If platform_driver_register() fails within vpss_init() resources are not
cleaned up. The patch fixes this issue by introducing the corresponding
error handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Evgeny Novikov <novikov@ispras.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Implementation of media controller centric device configuration will add
code to the CAMERARX support section, which is already quite big. Move
it to a separate file to make the code more manageable. No functional
change is included.
The cal_camerarx_init_regmap() function is kept in cal.c and renamed to
cal_init_camerarx_regmap() as it's not specific to one CAMERARX
instance, but related to the whole CAL device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for the split of the camerarx code to a separate file, move
the CAL I/O accessors to cal.h. This requires renaming the accessors
with a cal_prefix, as the current names are too generic and prone to
namespace clashes.
The reg_read() and read_write() macros, that cover both CAL and CAMERARX
register access, are split in two groups of inline functions, one for
CAL access and one for CAMERARX access.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for implementation of media controller centric device
configuration, move all the video node handling support to a separate
file.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Specifying 'int' explicitly is generally preferred in the kernel for
unsigned int types. Fix the only wrong occurrence.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The phy->sensor NULL check in cal_camerarx_get_external_rate() is not
needed, as the V4L2 video devices are only registered when the sensor is
bound. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The external pixel rate is retrieved when starting the camerarx and only
used then. There's no need to store it in the cal_camerarx structure, it
can be returned by cal_camerarx_get_external_info() and explicitly
passed to cal_camerarx_config().
While at it, rename cal_camerarx_get_external_info() to
cal_camerarx_get_external_rate() to better reflect the function's
purpose.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Refactor the camerarx start and stop procedure to group all the
corresponding operations in two functions, cal_camerarx_start() and
cal_camerarx_stop() instead of splitting them in multiple steps called
from the vb2 stream start and stop functions. This reduces the coupling
between the camerarx and the contexts, and better models the camerarx
hardware.
The cal_camerarx_start() is a reworked version of cal_camerarx_init()
with the description of the start procedure updated to match the AM65x,
DRA7[124567]x and DRA80xM TRMs. The cal_camerarx_wait_ready() function
is inlined in cal_camerarx_start() to better describe the start
procedure.
No functional change is included in the camerarx start and stop
procedures themselves, but the interleaving of the start steps with the
context configuration has been changed in cal_start_streaming().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for the camerarx refactoring, reorder functions without any
functional change to ease review of the refactoring itself.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_camerarx_max_lanes() function is a one-liner that has a single
caller. It doesn't improve readability. Inline it in its caller.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To avoid making the cal_ctx structure layoug depend on the size of the
cal_formats array, allocate the active_fmt array dynamically. This
prepares for splitting the driver in multiple files.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for splitting the V4L2 API support to a separate file, call
cal_ctx_v4l2_init_formats() from cal_ctx_v4l2_register().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable the media controller API by registering a media device and
initializing the media entities corresponding to the video devices. The
context initialization is slightly refactored as a result. The media
graph will be built in a subsequent change.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_dev structure stores the platform_device pointer, but most
accesses to that field need the device pointer. Store the struct device
pointer directly to simplify the code, and use to_platform_device() in
the two locations that need the platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Print the hardware revision in the X.Y.R format, which is more readable
that the 32-bit hex value. For the hardware info register, only print
its value if it doesn't contain what we expect.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Read the hardware revision and info right after allocating resources, as
there's no need to delay doing so until all initialization is complete.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Create four functions to handle initialization, cleanup, registration
and unregistration of the V4L2 (and soon media controller) objects:
- init() is meant to be called early at probe time to initialize the
objects, before they get used from within the kernel
- cleanup() is the counterpart of init, and is meant to be called at the
end of the remove sequence to free all objects
- register() is meant to be called at the end of the probe sequence, to
register the userspace-facing devices
- unregister() is the counterpart of register, and is meant to be called
at the beginning for the remove sequence, to disallow access from
userspace
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the CAL_NUM_CSI2_PORTS macro instead of the hardcoded numerical
value 2 to iterate over the CSI-2 ports.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The isvcirqset() isn't used. The isportirqset() doesn't increase
readability. Inline the latter and simply drop the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CAL_NUM_CSI2_PORTS macro isn't a register definition. Move it to
cal.c, and fix indentation of the other macros while at it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The driver happens the use the same number of CAMERARX and context, but
coupling their cleanup at remove time is wrong. To prepare for the
introduction of additional contexts, decouple the two.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_quickdump_regs() dumps registers for the two CAMERARX instances.
Retrieve those instances from the cal_dev directly instead of going
through the contexts, and simplify the code by using a loop.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The async notifier is meant to bind to subdevs connected to the CSI-2
ports. Those ports are modelled by the CAMERARX phy instances. To
prepare for additional decoupling of contexts and phys, make the
notifier operate on phys. We still initialize and register the context
V4L2 support in the async notifier complete operation as that's our
signal that the userspace API is ready to be exposed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to create one async notifier per CAL context. Merge them
all in a single notifier, stored in cal_dev.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The subdev notifier handling assumes a 1:1 mapping between CAL contexts
and notifiers. To prepare for merging the multiple notifiers into a
single one, retrieve the CAL context from the async subdev structure
instead of from the notifier.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The initialization of the context based on the connected sensor is split
between the async notifier .bound() and .complete() operations. Move it
all to a separate function and call it from .bound() operation to
prepare for the move of the notifiers from the contexts to the cal_dev.
Only V4L2 registration is kept in the .complete() operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use ARRAY_SIZE(cal->ctx) to iterate over the cal->ctx array instead of
using the numerical value from the CAL_NUM_CONTEXT macro (or, worse,
hardcoding the value 2). This will allow reworking contexts with less
changes in the code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The DT port nodes corresponding to the CSI-2 inputs belong to the
CAMERARX instances. Move parsing of the DT properties to a new
cal_camerarx_parse_dt() function, called by cal_camerarx_create().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_camerarx_create() function allocates resources with devm_*, and
thus doesn't need any manual cleanup. Those won't hold true for long, as
we will need to store resources that have no devm_* allocation variant
in cal_camerarx. Furthermore, devm_kzalloc() is the wrong memory
allocation API for structures that can be accessed from userspace, as
device nodes can be kept open across device removal.
Add a cal_camerarx_destroy() function to destroy a CAMERARX instance
explicitly, and switch to kzalloc() for memory allocation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In cal_remove(), unregister the video devices as the first operation,
before cleaning up the V4L2 objects, to avoid use-after-free. This isn't
a complete solution yet, as video nodes can be kept open across
unregistration.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Create cal_ctx_v4l2_unregister() and cal_ctx_v4l2_cleanup() functions to
unregister and cleanup the V4L2-related objects from the context, and
call them in cal_remove() and in the error path of cal_probe().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There's no need to delay most of the video device initialization until
the sensor subdevs are bound. Split the initialization and registration,
and perform the initialization when creating the context.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_device structure is meant to represent the whole device. In the
CAL case, this corresponds to the CAL, the CAMERARX instances and the
connected sensors. There should thus be a single v4l2_device instance.
Replace the per-context instance with a global instance in the cal_dev
structure.
Don't set the v4l2_device name manually as v4l2_device_register() sets
it to a value that is suitable for the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To prepare for decoupling the v4l2_device from the cal_ctx, don't set
the control handler in the v4l2_device and expect the video node to use
it automatically, but set the video node control handler directly. This
requires adding the sensor subdev controls to the control handler
manually, as that operation was performed on the v4l2_device by
v4l2_device_register_subdev().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Letting the v4l2_fwnode_endpoint_parse() function determine the bus type
automatically is deprecated. Set the bus type to DPHY manually as the TI
CAL only supports DPHY.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace the manual of_get_next_port() and of_get_next_endpoint()
implementations and the corresponding logic in the caller with a call to
of_graph_get_endpoint_by_regs(). This greatly simplifies OF parsing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Using the endpoint reg value to pass the CSI-2 source virtual channel ID
in DT is a hack, isn't documented in the DT bindings, and isn't used in
neither upstream DT nor TI official overlays. Hardcode the virtual
channel to 0 to simplify reworking the code, proper virtual channel
support will be implemented later.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_create_instance() function creates a CAL context. Rename it to
cal_ctx_create() to make its purpose more explicit.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_probe() function is a bit long, add comments to delimitate
sections in order to improve readability. The platform_set_drvdata()
call is moved to a more logical place as a result.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_get_camerarx_regmap() function is called in a single place.
Inline it in its caller, as it results in a clear code flow.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the syscon_regmap_lookup_by_phandle_args() function to replace
manual lookup of the syscon regmap offset. This simplifies the
cal_camerarx_init_regmap() implementation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Simplify the cal_probe() function by splitting the CAMERARX syscon
regmap retrieval to a separate function. A few local variables are
renamed in the process to shorten them (syscon_camerrx_*) or to make
them more accurate (parent isn't the parent OF node but the CAL device's
own OF node).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_dev field of the cal_dev structure is initialized but never
used. Drop it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Replace a manually unrolled loop with an explicit for loop to increase
readability when creating the CAMERARX and context instances. The
explicit NULL initialization of cal->phy[] and cal->ctx[] is removed, as
the cal structure is zeroed when allocated.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the context-specific print macro to replace the last usage of the
v4l2_* print macros.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of retrieving the struct device for the platform device from the
v4l2_device, get it from the platform device directly. This prepares for
cleanups related to v4l2_device handling.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The v4l2_capability bus_info field, filled by the VIDIOC_QUERYCAP ioctl
handler, specifies the location of the device in the system. For
platform devices, V4L2 specifies that the value must be "platform:"
followed by the device name. Fix the cal_querycap() function to set the
right value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The csi2_port field of the cal_ctx structure holds the context index,
and is independent from the CSI-2 port (even if it currently has the
same numerical value). Rename it to index to avoid the ambiguity.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename all functions related to contexts with a cal_ctx_ prefix to
increase readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_data_get_num_csi2_phy() function simply returns
cal->data->num_csi2_phy, and is not consistently used across the driver,
as most accesses to cal->data->num_csi2_phy are open-coded. We could fix
those open-coded accesses to use cal_data_get_num_csi2_phy(), but that
wouldn't bring much in terms of readability, so inline
cal_data_get_num_csi2_phy() in its only caller instead, and drop the
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Group the CAMERARX functions together to make the overall driver
structure easier to navigate. This only moves functions around, no
functional change is included.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Rename all functions related to CAMERARX with a cal_camerarx_ prefix,
and pass them a cal_camerarx pointer. This performs most of the
decoupling of the CAMERARX from the context.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The sensor is connected to the CAMERARX. Store its pointer, as well as
the sensor pixel rate and the endpoint, in the cal_camerarx. This
prepares for decoupling the cal_camerarx and cal_ctx.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Prepare for passing the cal_camerarx pointer instead of the cal_ctx
pointer to CAMERARX-related functions by adding print macros for
cal_camerarx.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Use the dev_* print macros instead of the v4l2_* print macros. This
prepares for a common print infrastructure that will also support the
cal_camerarx instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Store a pointer to the cal_dev and the cal_camerarx instance number in
the cal_camerarx structure. This prepares for passing a cal_camerarx
pointer instead of a cal_ctx pointer to multiple functions that deal
with the CAMERARX.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_camerarx structure describes the PHY, there's no need for an
internal structure named phy. Removed that level of indirection.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Name all variables that point to a cal_camerax instance 'phy' instead of
'cc'. The name 'cc' refers to Camera Core, but is not commonly used in
the driver or in datasheets.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Name all variables pointing to a cal_dev instance 'cal', instead of a
combination of 'caldev' and 'dev'. 'caldev' is only used in a few places
and could have been renamed to 'dev', but 'dev' is confusing as it's
also used for struct device instances. This generates lots of changes,
but increases readability.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_csi2_phy contains platform data for the CAMERARX blocks. Rename
it to cal_camerarx_data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The various data structures that describe the components of the camera
access layer (CAL) are named without much consistency. Start cleaning
this up by renaming the structure that describes the CAMERARX block,
cc_data, to cal_camerarx.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the csi2_phy_config() function to avoid its forward declaration. No
functional change is included.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_dev flags field is a copy of data->flags. Use the latter and
remove the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Remove structure fields that are never set, set and never read, or set
to a fixed value. This allows removal of a global variable and a macro.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The global static const cal_regmap_config template is only used in a
single location, to initialize 3 fields of a local variable. Two of
those fields then get overwritten. Remove the template and set the last
remaining field manually. Simplify the code by hardcoding the field
values instead of calculating them for a variable that always has the
same value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Now that no platform data fields are modified at runtime, make the
corresponding structures const. The const qualifier for integer fields
is removed as it's not required anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Several structure fields declared as int store positive values only.
Make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_csi2_phy structure has lost its 'fields' field that used to
clash with the 'base_fields' field. Rename base_fields to fields.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The PHY regmap fields are created dynamically at runtime. They don't
belong to the platform data that should be constant. Move them to the
cc_data structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In preparation to constify cal_csi2_phy, avoid modifying the base_fields
array at runtime. As the array now only needs to stored two values
instead of a full struct reg_field instance, save memory by using a
custom structure for the base_fields elements.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The base_fields field of cal_csi2_phy points to a fixed-size array of
struct reg_field. This level of indirection isn't needed, embed the
array directly in struct cal_csi2_phy.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Many loop indices only take positive values. Make them unsigned.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The found_port variable contains a boolean value, make it a bool.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
A few local variables are needlessly initialized. Fix them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The static cal_formats array contains const data, make it const. This
requires turning a few cal_fmt pointers into const pointers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Turn the reg_(read|write)_field() macros into inline functions for
additional type safety. Use the FIELD_GET() and FIELD_PREP() macros
internally instead of reinventing the wheel.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CAL_VERSION macro is used once only, in MODULE_VERSION(). This
doesn't improve readability, inline it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The cal_irq() function reads three IRQ status registers and stores their
values in three different variables. As each value is processed right
after reading the corresponding register, a single variable is enough.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The datasheet numbers the IRQ registers starting from 0. Update the
numbering scheme to match the datasheet.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The datasheet numbers the CSI-2 PHYs (external to the CAL) starting from
1, but the PPI inputs to the CAL starting from 0. Update the numbering
scheme for csi2_port to match the datasheet, which also simplifies the
driver by removing the need to constantly subtract 1 from the value.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The CPORT mentioned in the CAL documentation has nothing to do with the
CSI-2 ports. It's a remnant of CSI-3 support (or an attempt to achieve
it), and now only serves as an arbitraty tag value used to associate
data samples with contexts. Add a cport field to the cal_ctx structure
and use it instead of the CSI-2 port number where a CPORT is required by
the hardware. The value of the cport field is currently the same as the
csi2_port field, so there's no functional change, but this will help
reworking CPORT and CSI-2 port handling separately.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Move the cal_complete_ctx() function earlier in the file to avoid a
foward declaration. There is no functional change.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Memory allocated with 'v4l2_m2m_init()' must be freed by a corresponding
call to 'v4l2_m2m_release()'
Also reorder the code at the end of the probe function so that
'video_register_device()' is called last.
Update the error handling path accordingly.
Fixes: 5ce60d790a ("[media] s5p-g2d: Add DT based discovery support")
Fixes: 918847341a ("[media] v4l: add G2D driver for s5p device family")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: checkpatch: align with parenthesis]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
It's all too easy to get confused by the V4L2_TYPE_IS_OUTPUT
macro, when it's used as !V4L2_TYPE_IS_OUTPUT.
Reduce the risk of confusion with macro to explicitly
check for the CAPTURE queue type case.
This change does not affect functionality, and it's
only intended to make the code more readable.
Suggested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: checkpatch: align with parenthesis]
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The component offsets were computed in a negative way: they were
subtracted from the actual color component value.
So, a higher offset was reducing the component value.
This is not really desirable, as the offset is a 2's complements
number with 1 bit for sign and 12 value bits, so we would like to be able
to also add to the component, not only subtract.
The reported number in v4l2 is fine, a range from -4095 to +4095.
However when configuring a negative value for the offset, this would in
fact not function, because with the old code, the number was subtracted
from the max value. By setting something negative, it was overflowing in
fact. Reworked the component offsets by placing the real value as the
v4l2 ctrls.
Now, the values are the real number that is added or subtracted from
the component.
The negative values received from v4l2 are already in 2's complements, so
there is no need for conversion.
This actually simplifies a lot the computation procedure, eliminating the
need for the macros that convert from v4l2 values to ISC values and
viceversa.
Also the ZERO_VAL is eliminated, as 0 is now 0, as it's supposed to be.
Example after this change:
# v4l2-ctl --set-ctrl=red_component_offset=-150 -L
User Controls
brightness 0x00980900 (int) : min=-1024 max=1023 step=1 default=0 value=0 flags=slider
contrast 0x00980901 (int) : min=-2048 max=2047 step=1 default=16 value=20 flags=slider
white_balance_automatic 0x0098090c (bool) : default=1 value=0 flags=update
do_white_balance 0x0098090d (button) : flags=inactive, write-only, execute-on-write
gamma 0x00980910 (int) : min=0 max=3 step=1 default=3 value=3 flags=slider
red_component_gain 0x009819c0 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
blue_component_gain 0x009819c1 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
green_red_component_gain 0x009819c2 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
green_blue_component_gain 0x009819c3 (int) : min=0 max=8191 step=1 default=512 value=512 flags=slider
red_component_offset 0x009819c4 (int) : min=-4095 max=4095 step=1 default=0 value=-150 flags=slider
blue_component_offset 0x009819c5 (int) : min=-4095 max=4095 step=1 default=0 value=0 flags=slider
green_red_component_offset 0x009819c6 (int) : min=-4095 max=4095 step=1 default=0 value=0 flags=slider
green_blue_component_offset 0x009819c7 (int) : min=-4095 max=4095 step=1 default=0 value=0 flags=slider
The auto white balance algorithm is unchanged, but the obtained value to
'subtract' is now converted to negative and saved as a v4l2 control and
displayed properly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
TI DAVINCI SERIES MEDIA DRIVER: Replace HTTP links with HTTPS ones
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver didn't call _vb2_fop_release in the sun4i_csi_release
function. Without that call the vb2 queue is not properly canceled and
buffers may not be freed.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
For no obvious reason VB2_DMABUF was not enabled. Add this.
Also both read and write file ops were set, but this was not enabled
in the vb2 io_modes or in the device_caps capabilities. Drop this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This fixes a v4l2-compliance warning:
Required ioctls:
warn: v4l2-test-media.cpp(52): empty bus_info
test MEDIA_IOC_DEVICE_INFO: OK
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Setting the output CSC mode is required for a YUV output, but must not
be set when the input is also YUV. Doing this (as tested with a YUV420P
to YUV420P conversion) results in wrong colors.
Adapt the logic to only set the output CSC mode when the output is YUV and
the input is RGB. Also add a comment to clarify the rationale.
Fixes: f7e7b48e6d ("[media] rockchip/rga: v4l2 m2m support")
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This introduces two macros: RGA_COLOR_FMT_IS_YUV and RGA_COLOR_FMT_IS_RGB
which allow quick checking of the colorspace familily of a RGA color format.
These macros are then used to refactor the logic for CSC mode selection.
The two nested tests for input colorspace are simplified into a single one,
with a logical and, making the whole more readable.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
fimc_md_get_pinctrl() misses a check for pinctrl_lookup_state().
Add the missed check to fix it.
Fixes: 4163851f7b ("[media] s5p-fimc: Use pinctrl API for camera ports configuration]")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
