This patch built on top of Commit 299603e837
("net-gro: Prepare GRO stack for the upcoming tunneling support") to add
the support of the standard GRE (RFC1701/RFC2784/RFC2890) to the GRO
stack. It also serves as an example for supporting other encapsulation
protocols in the GRO stack in the future.
The patch supports version 0 and all the flags (key, csum, seq#) but
will flush any pkt with the S (seq#) flag. This is because the S flag
is not support by GSO, and a GRO pkt may end up in the forwarding path,
thus requiring GSO support to break it up correctly.
Currently the "packet_offload" structure only contains L3 (ETH_P_IP/
ETH_P_IPV6) GRO offload support so the encapped pkts are limited to
IP pkts (i.e., w/o L2 hdr). But support for other protocol type can
be easily added, so is the support for GRE variations like NVGRE.
The patch also support csum offload. Specifically if the csum flag is on
and the h/w is capable of checksumming the payload (CHECKSUM_COMPLETE),
the code will take advantage of the csum computed by the h/w when
validating the GRE csum.
Note that commit 60769a5dcd "ipv4: gre:
add GRO capability" already introduces GRO capability to IPv4 GRE
tunnels, using the gro_cells infrastructure. But GRO is done after
GRE hdr has been removed (i.e., decapped). The following patch applies
GRO when pkts first come in (before hitting the GRE tunnel code). There
is some performance advantage for applying GRO as early as possible.
Also this approach is transparent to other subsystem like Open vSwitch
where GRE decap is handled outside of the IP stack hence making it
harder for the gro_cells stuff to apply. On the other hand, some NICs
are still not capable of hashing on the inner hdr of a GRE pkt (RSS).
In that case the GRO processing of pkts from the same remote host will
all happen on the same CPU and the performance may be suboptimal.
I'm including some rough preliminary performance numbers below. Note
that the performance will be highly dependent on traffic load, mix as
usual. Moreover it also depends on NIC offload features hence the
following is by no means a comprehesive study. Local testing and tuning
will be needed to decide the best setting.
All tests spawned 50 copies of netperf TCP_STREAM and ran for 30 secs.
(super_netperf 50 -H 192.168.1.18 -l 30)
An IP GRE tunnel with only the key flag on (e.g., ip tunnel add gre1
mode gre local 10.246.17.18 remote 10.246.17.17 ttl 255 key 123)
is configured.
The GRO support for pkts AFTER decap are controlled through the device
feature of the GRE device (e.g., ethtool -K gre1 gro on/off).
1.1 ethtool -K gre1 gro off; ethtool -K eth0 gro off
thruput: 9.16Gbps
CPU utilization: 19%
1.2 ethtool -K gre1 gro on; ethtool -K eth0 gro off
thruput: 5.9Gbps
CPU utilization: 15%
1.3 ethtool -K gre1 gro off; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 12-13%
1.4 ethtool -K gre1 gro on; ethtool -K eth0 gro on
thruput: 9.26Gbps
CPU utilization: 10%
The following tests were performed on a different NIC that is capable of
csum offload. I.e., the h/w is capable of computing IP payload csum
(CHECKSUM_COMPLETE).
2.1 ethtool -K gre1 gro on (hence will use gro_cells)
2.1.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 8.53Gbps
CPU utilization: 9%
2.1.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 8.97Gbps
CPU utilization: 7-8%
2.1.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 8.83Gbps
CPU utilization: 5-6%
2.1.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.98Gbps
CPU utilization: 5%
2.2 ethtool -K gre1 gro off
2.2.1 ethtool -K eth0 gro off; csum offload disabled
thruput: 5.93Gbps
CPU utilization: 9%
2.2.2 ethtool -K eth0 gro off; csum offload enabled
thruput: 5.62Gbps
CPU utilization: 8%
2.2.3 ethtool -K eth0 gro on; csum offload disabled
thruput: 7.69Gbps
CPU utilization: 8%
2.2.4 ethtool -K eth0 gro on; csum offload enabled
thruput: 8.96Gbps
CPU utilization: 5-6%
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently Intel interrupt remapping drivers uses the "present" flag bit
in remapping entry to track whether an entry is allocated or not.
It works as follow:
1) allocate a remapping entry and set its "present" flag bit to 1
2) compose other fields for the entry
3) update the remapping entry with the composed value
The remapping hardware may access the entry between step 1 and step 3,
which then observers an entry with the "present" flag set but random
values in all other fields.
This patch introduces a dedicated bitmap to track remapping entry
allocation status instead of sharing the "present" flag with hardware,
thus eliminate the race window. It also simplifies the implementation.
Tested-and-reviewed-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
domain_has_cap is a misnomer bc the func name should be
the same for CONFIG_IOMMU_API and !CONFIG_IOMMU_API.
Signed-off-by: Upinder Malhi <umalhi@cisco.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the "recent" changes, am335x_tsc_se_update() has no longer any
users outside of this file so make it local.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Improve readability by creating a define for each microphone detection
level.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Jesse Gross says:
====================
[GIT net-next] Open vSwitch
Open vSwitch changes for net-next/3.14. Highlights are:
* Performance improvements in the mechanism to get packets to userspace
using memory mapped netlink and skb zero copy where appropriate.
* Per-cpu flow stats in situations where flows are likely to be shared
across CPUs. Standard flow stats are used in other situations to save
memory and allocation time.
* A handful of code cleanups and rationalization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the skb zerocopy logic written for nfnetlink queue available for
use by other modules.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP out_of_order_queue lock is not used, as queue manipulation
happens with socket lock held and we therefore use the lockless
skb queue routines (as __skb_queue_head())
We can use __skb_queue_head_init() instead of skb_queue_head_init()
to make this more consistent.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SDIO identifier for Broadcom WLAN devices were defined in the
brcmfmac SDIO driver. Moving the definitions in MMC header file
seems common sense.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SD0 may operate in low-voltage mode, with a minimum of 0.41V
and a maximum of 1.5V. This is indicated by bit 4 of FUSE7.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
broonie.e6264@m.evernote.com
Signed-off-by: Mark Brown <broonie@linaro.org>
This replaces the static initialization of a tpm_vendor_specific
structure in the drivers with the standard Linux idiom of providing
a const structure of function pointers.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe: did apply manually due to commit
191ffc6bde3 tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in freq-table. This also makes cpufreq stats
inconsistent as cpufreq-stats would fail to register because current frequency
of CPU isn't found in freq-table.
Because we don't want this change to affect boot process badly, we go for the
next freq which is >= policy->cur ('cur' must be set by now, otherwise we will
end up setting freq to lowest of the table as 'cur' is initialized to zero).
In case current frequency doesn't match any frequency from freq-table, we throw
warnings to user, so that user can get this fixed in their bootloaders or
freq-tables.
Reported-by: Carlos Hernandez <ceh@ti.com>
Reported-and-tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes boot loaders set CPU frequency to a value outside of frequency table
present with cpufreq core. In such cases CPU might be unstable if it has to run
on that frequency for long duration of time and so its better to set it to a
frequency which is specified in frequency table.
On some systems we can't really say what frequency we're running at the moment
and so for these we shouldn't check if we are running at a frequency present in
frequency table. And so we really can't force this for all the cpufreq drivers.
Hence we are created another flag here: CPUFREQ_NEED_INITIAL_FREQ_CHECK that
will be marked by platforms which want to go for this check at boot time.
Initially this is done for all ARM platforms but others may follow if required.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The comment about return value of acpi_table_parse() is incorrect.
This patch fix it.
Since all callers only check if the function succeeded or not, this
patch simplifies the semantics by returning -errno for all failure
cases. This will also simply the comment.
As suggested by Toshi Kani <toshi.kani@hp.com>, also change the stub
in linux/acpi.h to return -ENODEV.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch adds a inline_data recovery routine with the following policy.
[prev.] [next] of inline_data flag
o o -> recover inline_data
o x -> remove inline_data, and then recover data blocks
x o -> remove inline_data, and then recover inline_data
x x -> recover data blocks
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
macvlan needs vlan_pcpu_stats so make it visible even if compiling
without VLAN_8021Q support. Otherwise a very long compiler error happens.
Fixes: cdf3e274cf ("macvlan: unify macvlan_pcpu_stats and vlan_pcpu_stats")
Cc: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-By: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
* Add full port randomization support. Some crazy researchers found a way
to reconstruct the secure ephemeral ports that are allocated in random mode
by sending off-path bursts of UDP packets to overrun the socket buffer of
the DNS resolver to trigger retransmissions, then if the timing for the
DNS resolution done by a client is larger than usual, then they conclude
that the port that received the burst of UDP packets is the one that was
opened. It seems a bit aggressive method to me but it seems to work for
them. As a result, Daniel Borkmann and Hannes Frederic Sowa came up with a
new NAT mode to fully randomize ports using prandom.
* Add a new classifier to x_tables based on the socket net_cls set via
cgroups. These includes two patches to prepare the field as requested by
Zefan Li. Also from Daniel Borkmann.
* Use prandom instead of get_random_bytes in several locations of the
netfilter code, from Florian Westphal.
* Allow to use the CTA_MARK_MASK in ctnetlink when mangling the conntrack
mark, also from Florian Westphal.
* Fix compilation warning due to unused variable in IPVS, from Geert
Uytterhoeven.
* Add support for UID/GID via nfnetlink_queue, from Valentina Giusti.
* Add IPComp extension to x_tables, from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new routine cpufreq_notify_post_transition() which
can be used to send POSTCHANGE notification for new freq with or
without both {PRE|POST}CHANGE notifications for last freq. This is
useful at multiple places, especially for sending transition failure
notifications.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit eee0316497.
Jeff writes:
I have no objections to reverting it. There were concerns from
Al Viro that it'd be tough to get right by callers and I had
assumed it got dropped after that. I had planned on using it in
my btrfs sysfs exports patchset but came up with a better way.
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function is used to get a specific core when there is more than
one core of that specific type. This is used in bgmac to reset all GMAC
cores.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are same, so unify them as one; since macvlan is a kind of vlan,
vlan_pcpu_stats should be a proper name for vlan and macvlan.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are same, so unify them as one, pcpu_sw_netstats.
Define pcpu_sw_netstat in netdevice.h, remove pcpu_tstats
from if_tunnel and remove br_cpu_netstats from br_private.h
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_scan_fixups() isn't and shouldn't be called by the drivers directly, so
unexport it. And since Florian Fainelli's recent patches, the function is only
called locally, so we can make it static as well.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove adjust_state() callback from 'struct phy_device' since it seems to have
never been really used from the inception: phy_start_machine() has been always
called with 2nd argument equal to NULL.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Running 'checkpatch.pl' gives some errors and warnings:
- no spaces around =;
- * separated by space from the function name;
- { in function definition not on a separate line;
- line over 80 characters.
While fixing these, also fix the following style issues:
- file name in the heading comment;
- alignment not matching open paren.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Namespace related cleaning
* make cred_to_ucred static
* remove unused sock_rmalloc function
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds pci_enable_msi_range(), which supersedes the pci_enable_msi()
and pci_enable_msi_block() MSI interfaces.
It also adds pci_enable_msix_range(), which supersedes the
pci_enable_msix() MSI-X interface.
The old interfaces have three categories of return values:
negative: failure; caller should not retry
positive: failure; value indicates number of interrupts that *could*
have been allocated, and caller may retry with a smaller request
zero: success; at least as many interrupts allocated as requested
It is error-prone to handle these three cases correctly in drivers.
The new functions return either a negative error code or a number of
successfully allocated MSI/MSI-X interrupts, which is expected to lead to
clearer device driver code.
pci_enable_msi(), pci_enable_msi_block() and pci_enable_msix() still exist
unchanged, but are deprecated and may be removed after callers are updated.
[bhelgaas: tweak changelog]
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
This creates an MSI-X counterpart for pci_msi_vec_count(). Device drivers
can use this function to obtain maximum number of MSI-X interrupts the
device supports and use that number in a subsequent call to
pci_enable_msix().
pci_msix_vec_count() supersedes pci_msix_table_size() and returns a
negative errno if device does not support MSI-X interrupts. After this
update, callers must always check the returned value.
The only user of pci_msix_table_size() was the PCI-Express port driver,
which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.
Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().
pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Device drivers can use this interface to obtain the maximum number of MSI
interrupts the device supports and use that number, e.g., in a subsequent
call to pci_enable_msi_block().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
NFSv4 clients can contact port 2049 directly instead of needing the
portmapper.
Therefore a failure to register to the portmapper when starting an
NFSv4-only server isn't really a problem.
But Gareth Williams reports that an attempt to start an NFSv4-only
server without starting portmap fails:
#rpc.nfsd -N 2 -N 3
rpc.nfsd: writing fd to kernel failed: errno 111 (Connection refused)
rpc.nfsd: unable to set any sockets for nfsd
Add a flag to svc_version to tell the rpc layer it can safely ignore an
rpcbind failure in the NFSv4-only case.
Reported-by: Gareth Williams <gareth@garethwilliams.me.uk>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Kinglong Mee <kinglongmee@gmail.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
While we're at it and introduced CGROUP_NET_CLASSID, lets also make
NETPRIO_CGROUP more consistent with the rest of cgroups and rename it
into CONFIG_CGROUP_NET_PRIO so that for networking, we now have
CONFIG_CGROUP_NET_{PRIO,CLASSID}. This not only makes the CONFIG
option consistent among networking cgroups, but also among cgroups
CONFIG conventions in general as the vast majority has a prefix of
CONFIG_CGROUP_<SUBSYS>.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Zefan Li requested [1] to perform the following cleanup/refactoring:
- Split cgroupfs classid handling into net core to better express a
possible more generic use.
- Disable module support for cgroupfs bits as the majority of other
cgroupfs subsystems do not have that, and seems to be not wished
from cgroup side. Zefan probably might want to follow-up for netprio
later on.
- By this, code can be further reduced which previously took care of
functionality built when compiled as module.
cgroupfs bits are being placed under net/core/netclassid_cgroup.c, so
that we are consistent with {netclassid,netprio}_cgroup naming that is
under net/core/ as suggested by Zefan.
No change in functionality, but only code refactoring that is being
done here.
[1] http://patchwork.ozlabs.org/patch/304825/
Suggested-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Zefan Li <lizefan@huawei.com>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Function never used in current upstream code.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit c02cecb92e ("ARM: orion: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=N4//
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
register_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
deregister_mtd_parser never fails; hence make it return void.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
It seems the include guard was copied from of_net.h.
Signed-off-by: Philipp Rosenberger <philipp.rosenberger@xse.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
VM to VM GSO traffic is broken if it goes through VXLAN or GRE
tunnel and the physical NIC on the host supports hardware VXLAN/GRE
GSO offload (e.g. bnx2x and next-gen mlx4).
Two issues -
(VXLAN) VM traffic has SKB_GSO_DODGY and SKB_GSO_UDP_TUNNEL with
SKB_GSO_TCP/UDP set depending on the inner protocol. GSO header
integrity check fails in udp4_ufo_fragment if inner protocol is
TCP. Also gso_segs is calculated incorrectly using skb->len that
includes tunnel header. Fix: robust check should only be applied
to the inner packet.
(VXLAN & GRE) Once GSO header integrity check passes, NULL segs
is returned and the original skb is sent to hardware. However the
tunnel header is already pulled. Fix: tunnel header needs to be
restored so that hardware can perform GSO properly on the original
packet.
Signed-off-by: Wei-Chun Chao <weichunc@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trace event triggers added a lseek that uses the ftrace_filter_lseek()
function. Unfortunately, when function tracing is not configured in
that function is not defined and the kernel fails to build.
This is the second time that function was added to a file ops and
it broke the build due to requiring special config dependencies.
Make a generic tracing_lseek() that all the tracing utilities may
use.
Also, modify the old ftrace_filter_lseek() to return 0 instead of
1 on WRONLY. Not sure why it was a 1 as that does not make sense.
This also changes the old tracing_seek() to modify the file pos
pointer on WRONLY as well.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=IZCI
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Third Round of Renesas SH SCI Updates for v3.14
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
* tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
Signed-off-by: Olof Johansson <olof@lixom.net>
* Global
- Don't set plat_sci_port scbrr_algo_id field
- Declare SCIF register base and IRQ as resources
- Don't define SCIF platform data in an array
- Use macros to declare SCIF devices
* r7s72100 SoC (RZ/A1H)
- Add i2c clocks
* r8a7778 (R-Car M1)
- Add sound SCU clock support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=7k3L
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
From Simon Horman:
Third Round of Renesas ARM Based SoC Updates for v3.14
* Global
- Don't set plat_sci_port scbrr_algo_id field
- Declare SCIF register base and IRQ as resources
- Don't define SCIF platform data in an array
- Use macros to declare SCIF devices
* r7s72100 SoC (RZ/A1H)
- Add i2c clocks
* r8a7778 (R-Car M1)
- Add sound SCU clock support
* tag 'renesas-soc3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (43 commits)
arm: shmobile: r7s72100: add i2c clocks
ARM: shmobile: r8a7791: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7779: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7790: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7740: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a73a4: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7778: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r7s72100: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: sh73a0: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7790: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7791: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7778: Declare SCIF register base and IRQ as resources
ARM: shmobile: sh7372: Don't set plat_sci_port scbrr_algo_id field
ARM: shmobile: r8a7779: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7740: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a73a4: Declare SCIF register base and IRQ as resources
ARM: shmobile: r7s72100: Declare SCIF register base and IRQ as resources
ARM: shmobile: sh73a0: Declare SCIF register base and IRQ as resources
ARM: shmobile: sh7372: Declare SCIF register base and IRQ as resources
ARM: shmobile: r8a7790: Don't define SCIF platform data in an array
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSuX4DAAoJENfPZGlqN0++gP8QAJpeD1IWEevMeaz4Vbzbrqfw
LLPNcfoTqvfZgArcxY8iY0JEVDSVKzAKNlRpvUOGHKaD9wZxYlg/QkTj0BTdKohC
TVqxU8/JDs5PcCZ+auiOtS10/CcXz0yCuAYC2MMyeF7dLjTlm0VMQw9aLwVVIQrm
ol66AxE+aDzBLex874g4iylv2tJjhxYgP1CZHIigraXSGB0IioU6ahj99tvuiGnY
zhmOxXrfjGd4KIw0gr+VHh80TfoWbb9GSD0u0nguGMDp7XiiwBjufeQqnIUygEgz
uWZpYmWDq98ZZalBV2MiLIiCO4bjTnesLloG7ThZ/kZcjouqyLf2QuyRfJ7LoAsh
kH+iMW53DCg4qvjS9dmhptans4C6z2AhQx6FZqwcrZYeyimBX9G9IlBBttih4YEc
Em0+Zr6bBVfVXp0jUDgsv7R5KNEvFzzoKBlV4KoPhLKEBstbepkx9++K2gx6KJGf
u2Uy2Kyk4zEbDJauanJWQN7jczBpWjXlhrZeJMjXnwVLibk+1wlECfZTlGq/znhF
v7qVomsxgbElzBw+JI8FRein9R/SwDlGySjSrNsmZmDsX4+13QnI+x4t6ztyD/f0
ZG2ihbj0rpyGQxj9zZCS61wdOBhIMQS+dFXTd5CXmnYFGfscaDOS+zzKOHPg384G
mgUQmw7gJSUWBQ1u+Olk
=BQSn
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
From Simon Horman:
Second Round of Renesas SH SCI updates for v3.14
* Rework baud rate calculation
* Compute overrun_bit without using baud rate algo
* Remove unused GPIO request code
* Move overrun_bit and error_mask fields out of pdata
* Support resources passed through platform resources
* Don't check IRQ in verify port operation
* Set the UPF_FIXED_PORT flag
* Remove duplicate interrupt check in verify port op
* Simplify baud rate calculation algorithms
* Remove baud rate calculation algorithm 5
* Sort headers alphabetically
* tag 'renesas-sh-sci2-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit da660b4a3b ("arm: Move sp810.h to include/linux/amba/")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Commit 2960ed3468 ("ARM: netx: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following functions are not used outside of net/core/dev.c
and should be declared static.
call_netdevice_notifiers_info
__dev_remove_offload
netdev_has_any_upper_dev
__netdev_adjacent_dev_remove
__netdev_adjacent_dev_link_lists
__netdev_adjacent_dev_unlink_lists
__netdev_adjacent_dev_unlink
__netdev_adjacent_dev_link_neighbour
__netdev_adjacent_dev_unlink_neighbour
And the following are never used and should be deleted
netdev_lower_dev_get_private_rcu
__netdev_find_adj_rcu
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanups in netlink_tap code
* remove unused function netlink_clear_multicast_users
* make local function static
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.
This is done through the following elements:
- read tunneling device caps in QUERY_DEV_CAP
- add helper function to do SET_PORT for tunneling
- add DMFS VXLAN steering rule definitions
- add CQE and WQE checksum offload field definitions
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp has several points in its setsockopt path in which it issues deprecation
warnings. It seems like it might be handy to macrotize such a warning so other
subsystems can use it easily
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Add CRUSH_V2 feature (new indep mode and SET_* steps) to a set of
features supported by default.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
This allows all of the tunables to be overridden by a specific rule.
Reflects ceph.git commits d129e09e57fbc61cfd4f492e3ee77d0750c9d292,
0497db49e5973b50df26251ed0e3f4ac7578e66e.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
This aligns the internal identifier names with the user-visible names in
the decompiled crush map language.
Reflects ceph.git commit caa0e22e15e4226c3671318ba1f61314bf6da2a6.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Since we can specify the recursive retries in a rule, we may as well also
specify the non-recursive tries too for completeness.
Reflects ceph.git commit d1b97462cffccc871914859eaee562f2786abfd1.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Parameterize the attempts for the _firstn choose method, and apply the
rule-specified tries count to firstn mode as well. Note that we have
slightly different behavior here than with indep:
If the firstn value is not specified for firstn, we pass through the
normal attempt count. This maintains compatibility with legacy behavior.
Note that this is usually *not* actually N^2 work, though, because of the
descend_once tunable. However, descend_once is unfortunately *not* the
same thing as 1 chooseleaf try because it is only checked on a reject but
not on a collision. Sigh.
In contrast, for indep, if tries is not specified we default to 1
recursive attempt, because that is simply more sane, and we have the
option to do so. The descend_once tunable has no effect for indep.
Reflects ceph.git commit 64aeded50d80942d66a5ec7b604ff2fcbf5d7b63.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Explicitly control the number of sample attempts, and allow the number of
tries in the recursive call to be explicitly controlled via the rule. This
is important because the amount of time we want to spend looking for a
solution may be rule dependent (e.g., higher for the wide indep pool than
the rep pools).
(We should do the same for the other tunables, by the way!)
Reflects ceph.git commit c43c893be872f709c787bc57f46c0e97876ff681.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
For firstn mode, if we fail to make a valid placement choice, we just
continue and return a short result to the caller. For indep mode, however,
we need to make the position stable, and return an undefined value on
failed placements to avoid shifting later results to the left.
Reflects ceph.git commit b1d4dd4eb044875874a1d01c01c7d766db5d0a80.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
This is only present to size the temporary scratch arrays that we put on
the stack. Let the caller allocate them as they wish and remove the
limitation.
Reflects ceph.git commit 1cfe140bf2dab99517589a82a916f4c75b9492d1.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Pass the size of the weight vector into crush_do_rule() to ensure that we
don't access values past the end. This can happen if the caller misbehaves
and passes a weight vector that is smaller than max_devices.
Currently the monitor tries to prevent that from happening, but this will
gracefully tolerate previous bad osdmaps that got into this state. It's
also a bit more defensive.
Reflects ceph.git commit 5922e2c2b8335b5e46c9504349c3a55b7434c01a.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
This updates ceph_features.h so that it has all feature bits defined in
ceph.git. In the interim since the last update, ceph.git crossed the
"32 feature bits" point, and, the addition of the 33rd bit wasn't
handled correctly. The work-around is squashed into this commit and
reflects ceph.git commit 053659d05e0349053ef703b414f44965f368b9f0.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In preparation for ceph_features.h update, change all features fields
from unsigned int/u32 to u64. (ceph.git has ~40 feature bits at this
point.)
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
blk_mq_free_queue() is called from release handler of
queue kobject, so it needn't be called from drivers.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
Almost every function in include/linux/iommu.h has an empty stub
but the iommu_group_get_by_id() did not get one by mistake.
This adds an empty stub for iommu_group_get_by_id() for IOMMU_API
disabled config.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Commit 54ecf4f056 ("ARM: w90x900: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 2203747c97 ("ARM: omap: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
BBCH_BBCHEN_MASK is equivalent to TPS65910_SUPPLY_STATE_ENABLED.
So all regulators have the same enable_mask setting.
BBCH_BBCHEN_MASK and BBCH_BBCHEN_SHIFT are not used now, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove leftover code that is not used anywhere in current tree.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ACPI container devices require special hotplug handling, at least
on some systems, since generally user space needs to carry out
system-specific cleanup before it makes sense to offline devices in
the container. However, the current ACPI hotplug code for containers
first attempts to offline devices in the container and only then it
notifies user space of the container offline.
Moreover, after commit 202317a573 (ACPI / scan: Add acpi_device
objects for all device nodes in the namespace), ACPI device objects
representing containers are present as long as the ACPI namespace
nodes corresponding to them are present, which may be forever, even
if the container devices are physically detached from the system (the
return values of the corresponding _STA methods change in those
cases, but generally the namespace nodes themselves are still there).
Thus it is useful to introduce entities representing containers that
will go away during container hot-unplug.
The goal of this change is to address both the above issues.
The idea is to create a "companion" container system device for each
of the ACPI container device objects during the initial namespace
scan or on a hotplug event making the container present. That system
device will be unregistered on container removal. A new bus type
for container devices is added for this purpose, because device
offline and online operations need to be defined for them. The
online operation is a trivial function that is always successful
and the offline uses a callback pointed to by the container device's
offline member.
For ACPI containers that callback simply walks the list of ACPI
device objects right below the container object (its children) and
checks if all of their physical companion devices are offline. If
that's not the case, it returns -EBUSY and the container system
devivce cannot be put offline. Consequently, to put the container
system device offline, it is necessary to put all of the physical
devices depending on its ACPI companion object offline beforehand.
Container system devices created for ACPI container objects are
initially online. They are created by the container ACPI scan
handler whose hotplug.demand_offline flag is set. That causes
acpi_scan_hot_remove() to check if the companion container system
device is offline before attempting to remove an ACPI container or
any devices below it. If the check fails, a KOBJ_CHANGE uevent is
emitted for the container system device in question and user space
is expected to offline all devices below the container and the
container itself in response to it. Then, user space can finalize
the removal of the container with the help of its ACPI device
object's eject attribute in sysfs.
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only used in one file, no need to expose
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate ${DEBUGS_MOUNT_POINT}/clk if CONFIG_DEBUG_FS is set. This
eliminates the extra (annoying) step of enabling the config option
manually.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Commit 2203747c97 ("ARM: omap: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit a3b2924547 ("ARM: ep93xx: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We've seen so many instances of people invoking skb_tx_timestamp()
after the device already has been given the packet, that it's worth
being a little bit more verbose and explicit in this comment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This branch includes all the changes to Tegra's powergate driver for 3.14.
These are separate out, since the Tegra DRM changes for 3.14 rely on the
new APIs introduced here.
A few cleanups and fixes are included, plus additions of Tegra124 SoC
support, and a new API for manipulating Tegra's IO rail deep power down
states.
This branch is based on tag tegra-for-3.14-dmas-resets-rework, in order
to avoid conflicts with the addition of common reset controller support
to the powergate driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jJOV
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-powergate' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
From Stephen Warren:
ARM: tegra: powergate driver changes
This branch includes all the changes to Tegra's powergate driver for 3.14.
These are separate out, since the Tegra DRM changes for 3.14 rely on the
new APIs introduced here.
A few cleanups and fixes are included, plus additions of Tegra124 SoC
support, and a new API for manipulating Tegra's IO rail deep power down
states.
This branch is based on tag tegra-for-3.14-dmas-resets-rework, in order
to avoid conflicts with the addition of common reset controller support
to the powergate driver.
* tag 'tegra-for-3.14-powergate' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add IO rail support
ARM: tegra: Special-case the 3D clamps on Tegra124
ARM: tegra: Add Tegra124 powergate support
ARM: tegra: Export tegra_powergate_remove_clamping()
ARM: tegra: Export tegra_powergate_power_off()
ARM: tegra: Rename cpu0 powergate to crail
ARM: tegra: Fix some whitespace oddities
Signed-off-by: Olof Johansson <olof@lixom.net>
Bringing in the tegra dma/reset rework as a base for new SoC branches.
* tegra/dma-reset-rework: (81 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
As the davinci-gpio driver is migrated to use irqdomain
there is no need to pass the irq base for the gpio driver.
This patch removes this variable from davinci_gpio_platform_data
and also the refrences from the machine file.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Convert the davinci gpio driver to use irqdomain support.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[grygorii.strashko@ti.com:
- switch to use one irq-domain per all GPIO banks
- keep irq_create_mapping() call in gpio_to_irq_banked() as it
simply transformed to irq_find_mapping() if IRQ mapping exist
already]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Whfv
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO drivers, features and cleanups for the 3.14 cycle.
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
Pull percpu fix from Tejun Heo:
"A single commit to fix a spurious sparse warning coming from
DEFINE_PER_CPU()'s hack to support the use of weak symbols. Shouldn't
cause observable behavior change"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: fix spurious sparse warnings from DEFINE_PER_CPU()
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
The fields are not used anymore by board files, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field isn't set by any board, remote it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch introduces device tree support to the isp1704 charger driver.
Adding support involved moving the handling of the enable GPIO from board
code into the driver.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add method to get power supply by device tree phandle.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Computing the baud rate register value requires knowledge of the
hardware sampling rate. This information is currently encoded in a baud
rate calculation algorithm ID passed through platform data. However, it
can be derived from the port type directly in most cases.
Compute the sampling rate internally in the driver if the baud rate
calculation algorithm ID isn't specified, and allow platforms to
override the sampling rate through platform data in special cases (this
is only required for SCIFA ports on sh7723 and sh7724, the reason needs
to be investigated).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver requests at initialization time GPIOs passed through platform
data. No platform makes use of this feature, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
None of the fields is ever set by board code, and both of them are set
in the driver at probe time. Move them out of struct plat_sci_port to
struct sci_port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Memory and IRQ resources are currently passed to the driver through
platform data. Support passing them through the standard platform
resources mechanism instead. This deprecates platform data resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rewrite the baud rate register value calculations in easier to read
forms. The computed value isn't modified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch removing set_mode_hook function from board data and replacing
it with new string variable of notifier power supply device. After this
change it is possible to add DT support because driver does not need
specific board function anymore. Only static data and name of power supply
device is required.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager can parse charger_desc data from devicetree which is used
to register charger manager.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager driver used to check battery temperature through the
callback function passed by platform data. Unfortunatley, without that
pre-defined callback function, charger-manager can't get battery's
temperature at all. Also passing callback function through platform data
ruins DT support for charger-manager.
This patch mondifies charger-manager driver to get temperature of battery
without pre-defined callback function. Now, charger-manager can use either
of battery thermometer in fuel-gauge and ouside of battery. It uses
thermal framework interface for outer thermometer if thermal fw is
enabled. Otherwise, it tries to use fuel-gauge's through the power supply
interface.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This adds a pair of APIs that allows the generic PHY subsystem to
provide information on the PHY bus width. The PHY provider driver may
use phy_set_bus_width() to set the bus width that the PHY supports.
The controller driver may then use phy_get_bus_width() to fetch the
PHY bus width in order to properly configure the controller.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next
Linux 3.13-rc5
* tag 'v3.13-rc5': (231 commits)
Linux 3.13-rc5
aio: clean up and fix aio_setup_ring page mapping
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Don't set the INITRD_COMPRESS environment variable automatically
mm: fix build of split ptlock code
pstore: Don't allow high traffic options on fragile devices
mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
mm: page_alloc: revert NUMA aspect of fair allocation policy
Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
mm/hugetlb: check for pte NULL pointer in __page_check_address()
fix build with make 3.80
...
Conflicts:
drivers/usb/phy/Kconfig
This patch adds support for accuracy retrieval on fixed clocks.
It also adds a new dt property called 'clock-accuracy' to define the clock
accuracy.
This can be usefull for oscillator (RC, crystal, ...) definitions which are
always given an accuracy characteristic.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock accuracy is expressed in ppb (parts per billion) and represents
the possible clock drift.
Say you have a clock (e.g. an oscillator) which provides a fixed clock of
20MHz with an accuracy of +- 20Hz. This accuracy expressed in ppb is
20Hz/20MHz = 1000 ppb (or 1 ppm).
Clock users may need the clock accuracy information in order to choose
the best clock (the one with the best accuracy) across several available
clocks.
This patch adds clk accuracy retrieval support for common clk framework by
means of a new function called clk_get_accuracy.
This function returns the given clock accuracy expressed in ppb.
In order to get the clock accuracy, this implementation adds one callback
called recalc_accuracy to the clk_ops structure.
This callback is given the parent clock accuracy (if the clock is not a
root clock) and should recalculate the given clock accuracy.
This callback is optional and may be implemented if the clock is not
a perfect clock (accuracy != 0 ppb).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add new inode flags F2FS_INLINE_DATA and FI_INLINE_DATA to indicate
whether the inode has inline data.
Inline data makes use of inode block's data indices region to save small
file. Currently there are 923 data indices in an inode block. Since
inline xattr has made use of the last 50 indices to save its data, there
are 873 indices left which can be used for inline data. When
FI_INLINE_DATA is set, the layout of inode block's indices region is
like below:
+-----------------+
| | Reserved. reserve_new_block() will make use of
| i_addr[0] | i_addr[0] when we need to reserve a new data block
| | to convert inline data into regular one's.
|-----------------|
| | Used by inline data. A file whose size is less than
| i_addr[1~872] | 3488 bytes(~3.4k) and doesn't reserve extra
| | blocks by fallocate() can be saved here.
|-----------------|
| |
| i_addr[873~922] | Reserved for inline xattr
| |
+-----------------+
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
Signed-off-by: Huajun Li <huajun.li@intel.com>
Signed-off-by: Weihong Xu <weihong.xu@intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=lQsh
-----END PGP SIGNATURE-----
Merge tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux into drm-next
drm/tegra: Changes for v3.14-rc1
This series of changes brings DRM panel support as well as initial code
to register DSI hosts and peripherals and bind them to DSI drivers. The
panel and DSI code are both used by the simple panel driver.
The Tegra-specific changes build on top of this work to add support for
various panels found on Tegra boards. New drivers enable the DSI host
found on Tegra114 and a special hardware block that calibrates the pads
used for DSI and CSI. The host1x and the display controller drivers gain
basic Tegra124 support. To round of the new features, the DRM driver now
sports a very simple PRIME implementation.
In addition there are various improvements such as the host1x API being
exported so that client drivers (like the Tegra DRM driver) can be built
as modules. HDMI now does better power management and legacy FBDEV can
now be disabled via Kconfig (though it's still enabled by default). A
few sparse warnings have been squashed and various parts of the code
have become more robust.
* tag 'drm/for-3.14-rc1' of git://anongit.freedesktop.org/tegra/linux: (121 commits)
drm/tegra: fix compile w/ CONFIG_DYNAMIC_DEBUG
drm/tegra: Add PRIME support
drm/tegra: Relocate some output-specific code
drm/tegra: Add Tegra124 DC support
drm/tegra: Fix small leak on error in tegra_fb_alloc()
drm/tegra: Make legacy fbdev support optional
drm/tegra: Sort reverse-dependencies alphabetically
drm/tegra: Fix return value check
drm/tegra: Add DSI support
drm/tegra: Disable outputs for power-saving
drm/tegra: Track HDMI enable state
drm/tegra: Fix HDMI audio frequency typo
drm/tegra: Do not export tegra_bo_ops
drm/tegra: Remove spurious blank line
drm/tegra: Increase compile test coverage
drm/tegra: Allow the driver to be built as a module
gpu: host1x: Add Tegra124 support
gpu: host1x: clk_round_rate() can return a zero upon error
gpu: host1x: Fix build warnings
gpu: host1x: Increase compile test coverage
...
Add a generic event_command.set_trigger_filter() op implementation and
have the current set of trigger commands use it - this essentially
gives them all support for filters.
Syntactically, filters are supported by adding 'if <filter>' just
after the command, in which case only events matching the filter will
invoke the trigger. For example, to add a filter to an
enable/disable_event command:
echo 'enable_event:system:event if common_pid == 999' > \
.../othersys/otherevent/trigger
The above command will only enable the system:event event if the
common_pid field in the othersys:otherevent event is 999.
As another example, to add a filter to a stacktrace command:
echo 'stacktrace if common_pid == 999' > \
.../somesys/someevent/trigger
The above command will only trigger a stacktrace if the common_pid
field in the event is 999.
The filter syntax is the same as that described in the 'Event
filtering' section of Documentation/trace/events.txt.
Because triggers can now use filters, the trigger-invoking logic needs
to be moved in those cases - e.g. for ftrace_raw_event_calls, if a
trigger has a filter associated with it, the trigger invocation now
needs to happen after the { assign; } part of the call, in order for
the trigger condition to be tested.
There's still a SOFT_DISABLED-only check at the top of e.g. the
ftrace_raw_events function, so when an event is soft disabled but not
because of the presence of a trigger, the original SOFT_DISABLED
behavior remains unchanged.
There's also a bit of trickiness in that some triggers need to avoid
being invoked while an event is currently in the process of being
logged, since the trigger may itself log data into the trace buffer.
Thus we make sure the current event is committed before invoking those
triggers. To do that, we split the trigger invocation in two - the
first part (event_triggers_call()) checks the filter using the current
trace record; if a command has the post_trigger flag set, it sets a
bit for itself in the return value, otherwise it directly invoks the
trigger. Once all commands have been either invoked or set their
return flag, event_triggers_call() returns. The current record is
then either committed or discarded; if any commands have deferred
their triggers, those commands are finally invoked following the close
of the current event by event_triggers_post_call().
To simplify the above and make it more efficient, the TRIGGER_COND bit
is introduced, which is set only if a soft-disabled trigger needs to
use the log record for filter testing or needs to wait until the
current log record is closed.
The syscall event invocation code is also changed in analogous ways.
Because event triggers need to be able to create and free filters,
this also adds a couple external wrappers for the existing
create_filter and free_filter functions, which are too generic to be
made extern functions themselves.
Link: http://lkml.kernel.org/r/7164930759d8719ef460357f143d995406e4eead.1382622043.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add 'enable_event' and 'disable_event' event_command commands.
enable_event and disable_event event triggers are added by the user
via these commands in a similar way and using practically the same
syntax as the analagous 'enable_event' and 'disable_event' ftrace
function commands, but instead of writing to the set_ftrace_filter
file, the enable_event and disable_event triggers are written to the
per-event 'trigger' files:
echo 'enable_event:system:event' > .../othersys/otherevent/trigger
echo 'disable_event:system:event' > .../othersys/otherevent/trigger
The above commands will enable or disable the 'system:event' trace
events whenever the othersys:otherevent events are hit.
This also adds a 'count' version that limits the number of times the
command will be invoked:
echo 'enable_event:system:event:N' > .../othersys/otherevent/trigger
echo 'disable_event:system:event:N' > .../othersys/otherevent/trigger
Where N is the number of times the command will be invoked.
The above commands will will enable or disable the 'system:event'
trace events whenever the othersys:otherevent events are hit, but only
N times.
This also makes the find_event_file() helper function extern, since
it's useful to use from other places, such as the event triggers code,
so make it accessible.
Link: http://lkml.kernel.org/r/f825f3048c3f6b026ee37ae5825f9fc373451828.1382622043.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add 'stacktrace' event_command. stacktrace event triggers are added
by the user via this command in a similar way and using practically
the same syntax as the analogous 'stacktrace' ftrace function command,
but instead of writing to the set_ftrace_filter file, the stacktrace
event trigger is written to the per-event 'trigger' files:
echo 'stacktrace' > .../tracing/events/somesys/someevent/trigger
The above command will turn on stacktraces for someevent i.e. whenever
someevent is hit, a stacktrace will be logged.
This also adds a 'count' version that limits the number of times the
command will be invoked:
echo 'stacktrace:N' > .../tracing/events/somesys/someevent/trigger
Where N is the number of times the command will be invoked.
The above command will log N stacktraces for someevent i.e. whenever
someevent is hit N times, a stacktrace will be logged.
Link: http://lkml.kernel.org/r/0c30c008a0828c660aa0e1bbd3255cf179ed5c30.1382622043.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add 'snapshot' event_command. snapshot event triggers are added by
the user via this command in a similar way and using practically the
same syntax as the analogous 'snapshot' ftrace function command, but
instead of writing to the set_ftrace_filter file, the snapshot event
trigger is written to the per-event 'trigger' files:
echo 'snapshot' > .../somesys/someevent/trigger
The above command will turn on snapshots for someevent i.e. whenever
someevent is hit, a snapshot will be done.
This also adds a 'count' version that limits the number of times the
command will be invoked:
echo 'snapshot:N' > .../somesys/someevent/trigger
Where N is the number of times the command will be invoked.
The above command will snapshot N times for someevent i.e. whenever
someevent is hit N times, a snapshot will be done.
Also adds a new tracing_alloc_snapshot() function - the existing
tracing_snapshot_alloc() function is a special version of
tracing_snapshot() that also does the snapshot allocation - the
snapshot triggers would like to be able to do just the allocation but
not take a snapshot; the existing tracing_snapshot_alloc() in turn now
also calls tracing_alloc_snapshot() underneath to do that allocation.
Link: http://lkml.kernel.org/r/c9524dd07ce01f9dcbd59011290e0a8d5b47d7ad.1382622043.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
[ fix up from kbuild test robot <fengguang.wu@intel.com report ]
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The pm_generic_runtime_suspend|resume functions were implemented within
CONFIG_PM_RUNTIME.
As we also may use runtime PM callbacks during system suspend, to put
devices into low power state, we need to move the implementation of
pm_generic_runtime_suspend|resume to CONFIG_PM.
This change gives a power domain provision to invoke a platform
driver's runtime PM callback from a power domain's system PM callback.
This were earlier prevented by the platform bus, since it uses the
pm_generic_runtime_suspend|resume functions as runtime PM callbacks.
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
By having the runtime PM callbacks implemented for CONFIG_PM, these
becomes available in all combinations of CONFIG_PM_SLEEP and
CONFIG_PM_RUNTIME.
The benefit using this, is that we don't need to implement the wrapper
functions which handles runtime PM resourses, typically called from
both runtime PM and system PM callbacks. Instead the runtime PM
callbacks can be invoked directly from system PM callbacks, which is
useful for some drivers, subsystems and power domains.
Use the new macro SET_PM_RUNTIME_PM_OPS in cases were the above makes
sense. Make sure the callbacks are encapsulated within CONFIG_PM
instead of CONFIG_PM_RUNTIME.
Do note that the old macro SET_RUNTIME_PM_OPS, which is being quite
widely used right now, requires the callbacks to be defined for
CONFIG_PM_RUNTIME. In many cases it will certainly be convenient to
convert to the new macro above, but that will have to be distinguished
in case by case.
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We use the same approach as for the existing SET_SYSTEM_SLEEP_PM_OPS,
but for the late and early callbacks instead.
The new SET_LATE_SYSTEM_SLEEP_PM_OPS, defined for CONFIG_PM_SLEEP, will
point ->suspend_late, ->freeze_late and ->poweroff_late to the same
function. Vice verse happens for ->resume_early, ->thaw_early and
->restore_early.
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The arbitrary restriction on page counts offered by the core
migrate_page_move_mapping() code results in rather suspicious looking
fiddling with page reference counts in the aio_migratepage() operation.
To fix this, make migrate_page_move_mapping() take an extra_count parameter
that allows aio to tell the code about its own reference count on the page
being migrated.
While cleaning up aio_migratepage(), make it validate that the old page
being passed in is actually what aio_migratepage() expects to prevent
misbehaviour in the case of races.
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Define CPU interface offsets for the GICC_ABPR, GICC_APR, and GICC_IIDR
registers. Define distributor registers for the GICD_SPENDSGIR and the
GICD_CPENDSGIR. KVM/ARM needs to know about these definitions to fully
support save/restore of the VGIC.
Also define some masks and shifts for the various GICH_VMCR fields.
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Support creating the ARM VGIC device through the KVM_CREATE_DEVICE
ioctl, which can then later be leveraged to use the
KVM_{GET/SET}_DEVICE_ATTR, which is useful both for setting addresses in
a more generic API than the ARM-specific one and is useful for
save/restore of VGIC state.
Adds KVM_CAP_DEVICE_CTRL to ARM capabilities.
Note that we change the check for creating a VGIC from bailing out if
any VCPUs were created, to bailing out if any VCPUs were ever run. This
is an important distinction that shouldn't break anything, but allows
creating the VGIC after the VCPUs have been created.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
We store BAR information as a struct resource, which contains the CPU
address, not the bus address. Drivers often need the bus address, and
there's currently no convenient way to get it, so they often read the
BAR directly, or use the resource address (which doesn't work if there's
any translation between CPU and bus addresses).
Add pci_bus_address() to make this convenient.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
These interfaces:
pcibios_resource_to_bus(struct pci_dev *dev, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_dev *dev, *resource, *bus_region)
took a pci_dev, but they really depend only on the pci_bus. And we want to
use them in resource allocation paths where we have the bus but not a
device, so this patch converts them to take the pci_bus instead of the
pci_dev:
pcibios_resource_to_bus(struct pci_bus *bus, *bus_region, *resource)
pcibios_bus_to_resource(struct pci_bus *bus, *resource, *bus_region)
In fact, with standard PCI-PCI bridges, they only depend on the host
bridge, because that's the only place address translation occurs, but
we aren't going that far yet.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
kexec kernel will need exactly same mapping for EFI runtime memory
ranges. Thus here export the runtime ranges mapping to sysfs,
kexec-tools will assemble them and pass to 2nd kernel via setup_data.
Introducing a new directory /sys/firmware/efi/runtime-map just like
/sys/firmware/memmap. Containing below attribute in each file of that
directory:
attribute num_pages phys_addr type virt_addr
Signed-off-by: Dave Young <dyoung@redhat.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Export fw_vendor, runtime and config table physical addresses to
/sys/firmware/efi/{fw_vendor,runtime,config_table} because kexec kernels
need them.
From EFI spec these 3 variables will be updated to virtual address after
entering virtual mode. But kernel startup code will need the physical
address.
Signed-off-by: Dave Young <dyoung@redhat.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
tps65910 has a backup battery charger with a configurable voltage. This
patch adds a regulator for the backup battery.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add 'traceon' and 'traceoff' event_command commands. traceon and
traceoff event triggers are added by the user via these commands in a
similar way and using practically the same syntax as the analagous
'traceon' and 'traceoff' ftrace function commands, but instead of
writing to the set_ftrace_filter file, the traceon and traceoff
triggers are written to the per-event 'trigger' files:
echo 'traceon' > .../tracing/events/somesys/someevent/trigger
echo 'traceoff' > .../tracing/events/somesys/someevent/trigger
The above command will turn tracing on or off whenever someevent is
hit.
This also adds a 'count' version that limits the number of times the
command will be invoked:
echo 'traceon:N' > .../tracing/events/somesys/someevent/trigger
echo 'traceoff:N' > .../tracing/events/somesys/someevent/trigger
Where N is the number of times the command will be invoked.
The above commands will will turn tracing on or off whenever someevent
is hit, but only N times.
Some common register/unregister_trigger() implementations of the
event_command reg()/unreg() callbacks are also provided, which add and
remove trigger instances to the per-event list of triggers, and
arm/disarm them as appropriate. event_trigger_callback() is a
general-purpose event_command func() implementation that orchestrates
command parsing and registration for most normal commands.
Most event commands will use these, but some will override and
possibly reuse them.
The event_trigger_init(), event_trigger_free(), and
event_trigger_print() functions are meant to be common implementations
of the event_trigger_ops init(), free(), and print() ops,
respectively.
Most trigger_ops implementations will use these, but some will
override and possibly reuse them.
Link: http://lkml.kernel.org/r/00a52816703b98d2072947478dd6e2d70cde5197.1382622043.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Add a 'trigger' file for each trace event, enabling 'trace event
triggers' to be set for trace events.
'trace event triggers' are patterned after the existing 'ftrace
function triggers' implementation except that triggers are written to
per-event 'trigger' files instead of to a single file such as the
'set_ftrace_filter' used for ftrace function triggers.
The implementation is meant to be entirely separate from ftrace
function triggers, in order to keep the respective implementations
relatively simple and to allow them to diverge.
The event trigger functionality is built on top of SOFT_DISABLE
functionality. It adds a TRIGGER_MODE bit to the ftrace_event_file
flags which is checked when any trace event fires. Triggers set for a
particular event need to be checked regardless of whether that event
is actually enabled or not - getting an event to fire even if it's not
enabled is what's already implemented by SOFT_DISABLE mode, so trigger
mode directly reuses that. Event trigger essentially inherit the soft
disable logic in __ftrace_event_enable_disable() while adding a bit of
logic and trigger reference counting via tm_ref on top of that in a
new trace_event_trigger_enable_disable() function. Because the base
__ftrace_event_enable_disable() code now needs to be invoked from
outside trace_events.c, a wrapper is also added for those usages.
The triggers for an event are actually invoked via a new function,
event_triggers_call(), and code is also added to invoke them for
ftrace_raw_event calls as well as syscall events.
The main part of the patch creates a new trace_events_trigger.c file
to contain the trace event triggers implementation.
The standard open, read, and release file operations are implemented
here.
The open() implementation sets up for the various open modes of the
'trigger' file. It creates and attaches the trigger iterator and sets
up the command parser. If opened for reading set up the trigger
seq_ops.
The read() implementation parses the event trigger written to the
'trigger' file, looks up the trigger command, and passes it along to
that event_command's func() implementation for command-specific
processing.
The release() implementation does whatever cleanup is needed to
release the 'trigger' file, like releasing the parser and trigger
iterator, etc.
A couple of functions for event command registration and
unregistration are added, along with a list to add them to and a mutex
to protect them, as well as an (initially empty) registration function
to add the set of commands that will be added by future commits, and
call to it from the trace event initialization code.
also added are a couple trigger-specific data structures needed for
these implementations such as a trigger iterator and a struct for
trigger-specific data.
A couple structs consisting mostly of function meant to be implemented
in command-specific ways, event_command and event_trigger_ops, are
used by the generic event trigger command implementations. They're
being put into trace.h alongside the other trace_event data structures
and functions, in the expectation that they'll be needed in several
trace_event-related files such as trace_events_trigger.c and
trace_events.c.
The event_command.func() function is meant to be called by the trigger
parsing code in order to add a trigger instance to the corresponding
event. It essentially coordinates adding a live trigger instance to
the event, and arming the triggering the event.
Every event_command func() implementation essentially does the
same thing for any command:
- choose ops - use the value of param to choose either a number or
count version of event_trigger_ops specific to the command
- do the register or unregister of those ops
- associate a filter, if specified, with the triggering event
The reg() and unreg() ops allow command-specific implementations for
event_trigger_op registration and unregistration, and the
get_trigger_ops() op allows command-specific event_trigger_ops
selection to be parameterized. When a trigger instance is added, the
reg() op essentially adds that trigger to the triggering event and
arms it, while unreg() does the opposite. The set_filter() function
is used to associate a filter with the trigger - if the command
doesn't specify a set_filter() implementation, the command will ignore
filters.
Each command has an associated trigger_type, which serves double duty,
both as a unique identifier for the command as well as a value that
can be used for setting a trigger mode bit during trigger invocation.
The signature of func() adds a pointer to the event_command struct,
used to invoke those functions, along with a command_data param that
can be passed to the reg/unreg functions. This allows func()
implementations to use command-specific blobs and supports code
re-use.
The event_trigger_ops.func() command corrsponds to the trigger 'probe'
function that gets called when the triggering event is actually
invoked. The other functions are used to list the trigger when
needed, along with a couple mundane book-keeping functions.
This also moves event_file_data() into trace.h so it can be used
outside of trace_events.c.
Link: http://lkml.kernel.org/r/316d95061accdee070aac8e5750afba0192fa5b9.1382622043.git.tom.zanussi@linux.intel.com
Signed-off-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Idea-by: Steve Rostedt <rostedt@goodmis.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Some pstore backing devices use on board flash as persistent
storage. These have limited numbers of write cycles so it
is a poor idea to use them from high frequency operations.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In struct page we have enough space to fit long-size page->ptl there,
but we use dynamically-allocated page->ptl if size(spinlock_t) is larger
than sizeof(int).
It hurts 64-bit architectures with CONFIG_GENERIC_LOCKBREAK, where
sizeof(spinlock_t) == 8, but it easily fits into struct page.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add prototype declaration of function memory_block_size_bytes() to
the header file include/linux/memory.h.
This eliminates the following warning in memory.c:
drivers/base/memory.c:87:1: warning: no previous prototype for ‘memory_block_size_bytes’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pci/msi:
PCI/MSI: Make pci_enable_msi/msix() 'nvec' argument type as int
PCI/MSI: Return -ENOSYS for unimplemented interfaces, not -1
PCI/MSI: Return msix_capability_init() failure if populate_msi_sysfs() fails
s390/PCI: Remove superfluous check of MSI type
s390/PCI: Fix single MSI only check
PCI/MSI: Export MSI mode using attributes, not kobjects
This isolates the custom S3C64xx GPIO definition table to
<linux/platform_data/gpio-samsung-s3x64xx.h> as this is
used in a few different places in the kernel, removing the
need to depend on the implicit inclusion of <mach/gpio.h>
from <linux/gpio.h> and thus getting rid of a few nasty
cross-dependencies.
Also delete the CONFIG_SAMSUNG_GPIO_EXTRA stuff. Instead
roof the number of GPIOs for this platform:
First sum up all the GPIO banks from A to Q: 187 GPIOs.
Add the 16 "board GPIOs" and the roof for SAMSUNG_GPIO_EXTRA,
128, so in total maximum 187+16+128 = 331 GPIOs, so let's
take the same roof as for S3C24XX: 512. This way we can do
away with the GPIO calculation macros for GPIO_BOARD_START,
BOARD_NR_GPIOS and the definition of ARCH_NR_GPIOS.
Cc: Mark Brown <broonie@kernel.org>
[on Mini6410 board]
Tested-by: Tomasz Figa <t.figa@samsung.com>
[for changes in mach-s3c64xx]
Acked-by: Tomasz Figa <t.figa@samsung.com>
Tested-by: Mark Brown <broonie@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This isolates the custom S3C24xx GPIO definition table to
<linux/platform_data/gpio-samsung-s3x24xx.h> as this is
used in a few different places in the kernel, removing the
need to depend on the implicit inclusion of <mach/gpio.h>
from <linux/gpio.h> and thus getting rid of a few nasty
cross-dependencies.
We also delete the nifty CONFIG_S3C24XX_GPIO_EXTRA stuff.
The biggest this can ever be for the S3C24XX is
CONFIG_S3C24XX_GPIO_EXTRA = 128, and then for CPU_S3C2443 or
CPU_S3C2416 32*12 GPIOs are added, so 32*12+128 = 512
is the absolute roof value on this platform. So we set
the size of ARCH_NR_GPIO to this and the GPIOs array will
fit any S3C24XX platform, as per pattern from other archs.
ChangeLog v2->v3:
- Move the movement of the S3C64XX gpio.h file out of
this patch and into the follow-up patch where it belongs.
ChangeLog v1->v2:
- Added an #ifdef ARCH_S3C24XX around the header inclusion
in drivers/gpio/gpio-samsung.c as we would otherwise
have colliding definitions when compiling S3C64XX.
- Rename inclusion guard in the header file.
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make pci_enable_msi_block(), pci_enable_msi_block_auto() and
pci_enable_msix() consistent with regard to the type of 'nvec' argument.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to net, ixgbe and e1000e.
David provides compiler fixes for e1000e.
Don provides a fix for ixgbe to resolve a compile warning.
John provides a fix to net where it is useful to be able to walk all
upper devices when bringing a device online where the RTNL lock is held.
In this case, it is safe to walk the all_adj_list because the RTNL lock is
used to protect the write side as well. This patch adds a check to see
if the RTNL lock is held before throwing a warning in
netdev_all_upper_get_next_dev_rcu().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the platform code to pass PHY's IRQ to the driver. Print this IRQ along
with the other PHY datails in sh_eth_phy_init().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI MSI sysfs code is a mess with kobjects for things that don't really
need to be kobjects. This patch creates attributes dynamically for the MSI
interrupts instead of using kobjects.
Note, this removes a directory from sysfs. Old MSI kobjects:
pci_device
└── msi_irqs
└── 40
└── mode
New MSI attributes:
pci_device
└── msi_irqs
└── 40
As there was only one file "mode" with the kobject model, the interrupt
number is now a file that returns the "mode" of the interrupt (msi vs.
msix).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
It can be a bit confusing when looking for checksumming flags that
the actual comment for this resides elsewhere further below in the
header file.
Thus, bring the documentation where we define these flags, and
slightly improve the doc text to make it a bit more clear/readable.
Also, whitespace-align values of the define while at it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an accessor function for IRQ_PER_CPU flag.
The accessor function is useful to determine whether an IRQ is percpu or not.
This patch is based on an older patch posted by Chris Smith here [1].
There is a minor change w.r.t. Chris's original patch: The accessor function
is renamed as 'irq_is_percpu' instead of 'irq_is_per_cpu'.
[1]: http://lkml.indiana.edu/hypermail/linux/kernel/1207.3/02955.html
Signed-off-by: Chris Smith <chris.smith@st.com>
Signed-off-by: Vinayak Kale <vkale@apm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
VFIO currently allocates it's own dynamic chardev range, reserving the
first minor for the control part of the interface (/dev/vfio/vfio) and
the remainder for VFIO groups (/dev/vfio/$GROUP). This works, but it
doesn't support auto loading. For instance when libvirt checks for
VFIO support it looks for /dev/vfio/vfio, which currently doesn't
exist unless the vfio module is loaded. By converting the control
device to a misc driver and reserving a static minor, we can enable
auto loading.
Reserving the minor is a prerequist to that conversion. Minor 196
is unused by anything currently in the kernel.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds omap control module support for USBSS in AM437x SoC.
Update DT binding information to reflect these changes.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Linux 3.13-rc4
* tag 'v3.13-rc4': (1001 commits)
Linux 3.13-rc4
null_blk: mem garbage on NUMA systems during init
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Revert "selinux: consider filesystem subtype in policies"
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
ARM: fix asm/memory.h build error
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
...
Signed-off-by: Felipe Balbi <balbi@ti.com>
Certain use-cases require the DRE to be disabled so expose registers
necessary to control the DRE enables.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to documentation on barriers, stores issued before a LOCK can
complete after the lock implying that it's possible tlb_flush_pending
can be visible after a page table update. As per revised documentation,
this patch adds a smp_mb__before_spinlock to guarantee the correct
ordering.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a few subtle races, between change_protection_range (used by
mprotect and change_prot_numa) on one side, and NUMA page migration and
compaction on the other side.
The basic race is that there is a time window between when the PTE gets
made non-present (PROT_NONE or NUMA), and the TLB is flushed.
During that time, a CPU may continue writing to the page.
This is fine most of the time, however compaction or the NUMA migration
code may come in, and migrate the page away.
When that happens, the CPU may continue writing, through the cached
translation, to what is no longer the current memory location of the
process.
This only affects x86, which has a somewhat optimistic pte_accessible.
All other architectures appear to be safe, and will either always flush,
or flush whenever there is a valid mapping, even with no permissions
(SPARC).
The basic race looks like this:
CPU A CPU B CPU C
load TLB entry
make entry PTE/PMD_NUMA
fault on entry
read/write old page
start migrating page
change PTE/PMD to new page
read/write old page [*]
flush TLB
reload TLB from new entry
read/write new page
lose data
[*] the old page may belong to a new user at this point!
The obvious fix is to flush remote TLB entries, by making sure that
pte_accessible aware of the fact that PROT_NONE and PROT_NUMA memory may
still be accessible if there is a TLB flush pending for the mm.
This should fix both NUMA migration and compaction.
[mgorman@suse.de: fix build]
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
do_huge_pmd_numa_page() handles the case where there is parallel THP
migration. However, by the time it is checked the NUMA hinting
information has already been disrupted. This patch adds an earlier
check with some helpers.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1b3a5d02ee ("reboot: move arch/x86 reboot= handling to generic
kernel") moved reboot= handling to generic code. In the process it also
removed the code in native_machine_shutdown() which are moving reboot
process to reboot_cpu/cpu0.
I guess that thought must have been that all reboot paths are calling
migrate_to_reboot_cpu(), so we don't need this special handling. But
kexec reboot path (kernel_kexec()) is not calling
migrate_to_reboot_cpu() so above change broke kexec. Now reboot can
happen on non-boot cpu and when INIT is sent in second kerneo to bring
up BP, it brings down the machine.
So start calling migrate_to_reboot_cpu() in kexec reboot path to avoid
this problem.
Bisected by WANG Chao.
Reported-by: Matthew Whitehead <mwhitehe@redhat.com>
Reported-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Tested-by: Baoquan He <bhe@redhat.com>
Tested-by: WANG Chao <chaowang@redhat.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function tty_vhangup_locked() was deprecated, removed it
from the tty.h also.
Signed-off-by: Liu, Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipgre_header_parse() needs to parse the tunnel's ip header and it
uses mac_header to locate the iphdr. This got broken when gre tunneling
was refactored as mac_header is no longer updated to point to iphdr.
Introduce skb_pop_mac_header() helper to do the mac_header assignment
and use it in ipgre_rcv() to fix msg_name parsing.
Bug introduced in commit c544193214 (GRE: Refactor GRE tunneling code.)
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPV6_PMTU_INTERFACE is the same as IPV6_PMTU_PROBE for ipv6. Add it
nontheless for symmetry with IPv4 sockets. Also drop incoming MTU
information if this mode is enabled.
The additional bit in ipv6_pinfo just eats in the padding behind the
bitfield. There are no changes to the layout of the struct at all.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
* pci/vc:
PCI: Rename PCI_VC_PORT_REG1/2 to PCI_VC_PORT_CAP1/2
PCI: Add Virtual Channel to save/restore support
PCI: Add support for save/restore of extended capabilities
PCI: Add pci_wait_for_pending() (refactor pci_wait_for_pending_transaction())
Remove sec_reg* helpers as they are not used anymore. These helpers were
error-prone as they mixed u8 with unsigned int and they changed order of
some of parameters (val and mask in sec_reg_update()).
Also the helpers didn't give any way of useful abstraction as they just
called corresponding regmap function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=t/v5
-----END PGP SIGNATURE-----
Merge tag 's2mps11-build' into regulator-s5m8767 since a following patch
depend on it.
regulator/clk: Fix s2mps11 build
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
The 'direction' member of 'struct dma_slave_config' is of data
type 'enum dma_transfer_direction', so update the kernel-doc comment
for 'struct dma_slave_config' to refer to appropriate values.
Signed-off-by: Alexander Popov <a13xp0p0v88@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add symbols for hard-coded values of BUCK_RAMP field in DVS_RAMP
register. This simplifies a little the code as register update is called
only once.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix kernel-doc warning for duplicate definition of 'kmalloc':
Documentation/DocBook/kernel-api.xml:9483: element refentry: validity error : ID API-kmalloc already defined
<refentry id="API-kmalloc">
Also combine the kernel-doc info from the 2 kmalloc definitions into one
block and remove the "see kcalloc" comment since kmalloc now contains the
@flags info.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
It is useful to be able to walk all upper devices when bringing
a device online where the RTNL lock is held. In this case it
is safe to walk the all_adj_list because the RTNL lock is used
to protect the write side as well.
This patch adds a check to see if the rtnl lock is held before
throwing a warning in netdev_all_upper_get_next_dev_rcu().
Also because we now have a call site for lockdep_rtnl_is_held()
outside COFIG_LOCK_PROVING an inline definition returning 1 is
needed. Similar to the rcu_read_lock_is_held().
Fixes: 2a47fa45d4 ("ixgbe: enable l2 forwarding acceleration for macvlans")
CC: Veaceslav Falico <vfalico@redhat.com>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we fail to remove a conflicting fb driver, we need to abort the
loading of the second driver to avoid likely kernel panics.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While we don't really have any infrastructure for making use of VC
support, the system BIOS can configure the topology to non-default
VC values prior to boot. This may be due to silicon bugs, desire to
reserve traffic classes, or perhaps just BIOS bugs. When we reset
devices, the VC configuration may return to default values, which can
be incompatible with devices upstream. For instance, Nvidia GRID
cards provide a PCIe switch and some number of GPUs, all supporting
VC. The power-on default for VC is to support TC0-7 across VC0,
however some platforms will only enable TC0/VC0 mapping across the
topology. When we do a secondary bus reset on the downstream switch
port, the GPU is reset to a TC0-7/VC0 mapping while the opposite end
of the link only enables TC0/VC0. If the GPU attempts to use TC1-7,
it fails.
This patch attempts to provide complete support for VC save/restore,
even beyond the minimally required use case above. This includes
save/restore and reload of the arbitration table, save/restore and
reload of the port arbitration tables, and re-enabling of the
channels for VC, VC9, and MFVC capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Current save/restore is specific to standard capabilities.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We currently have two instance of this loop which waits for a pending bit
to clear in a status dword. Generalize the function for future users.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Adds skb_copy_hash to copy rxhash and l4_rxhash from one skb to another.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function skb_set_rxash was added for drivers to call to set
the rxhash in an skb. The type of hash is also specified as
a parameter (L2, L3, L4, or unknown type).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several places 'skb->rxhash = 0' is being done to clear the
rxhash value in an skb. This does not clear l4_rxhash which could
still be set so that the rxhash wouldn't be recalculated on subsequent
call to skb_get_rxhash. This patch adds an explict function to clear
all the rxhash related information in the skb properly.
skb_clear_hash_if_not_l4 clears the rxhash only if it is not marked as
l4_rxhash.
Fixed up places where 'skb->rxhash = 0' was being called.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing name of function as part of making the hash in skbuff to be
generic property, not just for receive path.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fixes from Ingo Molnar:
"Three fixes for scheduler crashes, each triggers in relatively rare,
hardware environment dependent situations"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Rework sched_fair time accounting
math64: Add mul_u64_u32_shr()
sched: Remove PREEMPT_NEED_RESCHED from generic code
sched: Initialize power_orig for overlapping groups
These function to manipulate multiple addresses are not used anywhere
in current net-next tree. Some out of tree code maybe using these but
too bad; they should submit their code upstream..
Also, make __hw_addr_flush local since only used by dev_addr_lists.c
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of updates for the 3.14 stream...
For the Bluetooth bits, Gustavo says:
"This is the first batch of patches intended for 3.14. There is
nothing big here. Most of the code are refactors, clean up, small
fixes, plus some new device id support."
And...
"More patches to 3.14. Here we have the support for Low Energy
Connection Oriented Channels (LE CoC). Basically, as the name says,
this adds supports for connection oriented channels in the same way
we already have them for BR/EDR connections so profiles/protocols
that work on top of BR/EDR can now work on LE plus a plenty of new
possibilities for LE."
For the ath10k bits, Kalle says:
"Janusz and Marek implemented DFS support to ath10k, but the code is
not enabled yet due to missing cfg80211/mac80211 patches (it will be
enabled in the next pull request). Michal did some device reset fixes
and made it possible for ath10k to share an interrupt with another
device. And lots of smaller fixes from different people."
For the iwlwifi bits, Emmanuel says:
"I have here a big rework of the rate control by Eyal. This is obviously
the biggest part of this batch.
I also have enhancement of protection flags by Avri and a few bits for
WoWLAN by Eliad and Luca. Johannes cleans up the debugfs plus a few
fixes. I provided a few things for Bluetooth coexistence.
Besides this we have an implementation for low priority scan."
Along with all that, there are big batches of updates to mwifiex and
ath9k, Jeff Kirsher's FSF address fix patches, and a handful of other
bits here and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds helper functions to resume and suspend a given phy_device
by calling the corresponding driver callbacks if available.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We introduce a new hashing library that is meant to be used in
the contexts where speed is more important than uniformity of the
hashed values. The hash library leverages architecture specific
implementation to achieve high performance and fall backs to
jhash() for the generic case.
On Intel-based x86 architectures, the library can exploit the crc32l
instruction, part of the Intel SSE4.2 instruction set, if the
instruction is supported by the processor. This implementation
is twice as fast as the jhash() implementation on an i7 processor.
Additional architectures, such as Arm64 provide instructions for
accelerating the computation of CRC, so they could be added as well
in follow-up work.
Signed-off-by: Francesco Fusco <ffusco@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Thomas Graf <tgraf@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.
For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().
Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.
This patch modifies UDC drivers by adding support for maxpacket_limit.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 17438217a6 on request
of Linus Walleij:
Greg can you please drop or revert
commit 17438217a6
"serial: pl011: use DMA RX polling by default"
from the TTY tree until this has been sorted out?
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This branch includes all the changes to Tegra's powergate driver for 3.14.
These are separate out, since the Tegra DRM changes for 3.14 rely on the
new APIs introduced here.
A few cleanups and fixes are included, plus additions of Tegra124 SoC
support, and a new API for manipulating Tegra's IO rail deep power down
states.
This branch is based on tag tegra-for-3.14-dmas-resets-rework, in order
to avoid conflicts with the addition of common reset controller support
to the powergate driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=jJOV
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-powergate' into drm/for-next
ARM: tegra: powergate driver changes
This branch includes all the changes to Tegra's powergate driver for 3.14.
These are separate out, since the Tegra DRM changes for 3.14 rely on the
new APIs introduced here.
A few cleanups and fixes are included, plus additions of Tegra124 SoC
support, and a new API for manipulating Tegra's IO rail deep power down
states.
This branch is based on tag tegra-for-3.14-dmas-resets-rework, in order
to avoid conflicts with the addition of common reset controller support
to the powergate driver.
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' into drm/for-next
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
Add support for mkdir(2), rmdir(2) and rename(2) syscalls. This is
implemented through optional kernfs_dir_ops callback table which can
be specified on kernfs_create_root(). An implemented callback is
invoked when the matching syscall is invoked.
As kernfs keep dcache syncs with internal representation and
revalidates dentries on each access, the implementation of these
methods is extremely simple. Each just discovers the relevant
kernfs_node(s) and invokes the requested callback which is allowed to
do any kernfs operations and the end result doesn't necessarily have
to match the expected semantics of the syscall.
This will be used to convert cgroup to use kernfs instead of its own
filesystem implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because sysfs used struct attribute which are supposed to stay
constant, sysfs didn't copy names when creating regular files. The
specified string for name was supposed to stay constant. Such
distinction isn't inherent for kernfs. kernfs_create_file[_ns]()
should be able to take the same @name as kernfs_create_dir[_ns]()
As there can be huge number of sysfs attributes, we still want to be
able to use static names for sysfs attributes. This patch renames
kernfs_create_file_ns_key() to __kernfs_create_file() and adds
@name_is_static parameter so that the caller can explicitly indicate
that @name can be used without copying. kernfs is updated to use
KERNFS_STATIC_NAME to distinguish static and copied names.
This patch doesn't introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysfs assumed 0755 for all newly created directories and kernfs
inherited it. This assumption is unnecessarily restrictive and
inconsistent with kernfs_create_file[_ns](). This patch adds @mode
parameter to kernfs_create_dir[_ns]() and update uses in sysfs
accordingly. Among others, this will be useful for implementations of
the planned ->mkdir() method.
This patch doesn't introduce any behavior differences.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into core/locking
Merge Linux 3.13-rc4, to refresh this rather old tree with the latest fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
commit 887c290e (sched/numa: Decide whether to favour task or group weights
based on swap candidate relationships) drop the check against
sysctl_numa_balancing_settle_count, this patch remove the sysctl.
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Link: http://lkml.kernel.org/r/1386833006-6600-1-git-send-email-liwanp@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Certain drives cannot handle queued TRIM commands properly, even
though support is indicated in the IDENTIFY DEVICE buffer. This patch
allows for disabling the commands for the affected drives and apply it
to the Micron/Crucial M500 SSDs which exhibit incorrect protocol
behavior when issued queued TRIM commands, which could lead to silent
data corruption.
tj: Merged two unnecessarily split patches and made minor edits
including shortening horkage name.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/g/1387246554-7311-1-git-send-email-marc.ceeeee@gmail.com
Cc: stable@vger.kernel.org # 3.12+
Now that spi_device->mode is a u16, the chip_select, bits_per_mode,
and mode fields pack poorly, taking 8 bytes: four data and four
padding. By moving (u8)bits_per_word up one position, to after
(u8)chip_select, they pack better and only use 4 bytes.
Signed-off-by: Trent Piepho <tpiepho@gmail.com>
Reviewed-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>g
Signed-off-by: Mark Brown <broonie@linaro.org>
Add tegra_io_rail_power_off() and tegra_io_rail_power_on() functions to
put IO rails into or out of deep powerdown mode, respectively.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Three new gates have been added for Tegra124: SOR, VIC and IRAM. In
addition, PCIe and SATA gates are again supported, like on Tegra20 and
Tegra30.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Adds controller error handling on resume power management. If the device
fails to initialize, the device is queued for a reset. If the reset fails,
a thread is spawned to remove the pci device.
If the device resumes as "busy", the device is responding to admin
commands but will not create IO queues. In this case, we need to remove
the gendisks and free the IO queues since they can't be used and may be
holding bios in their lists.
From testing, the dma pools require a pci device so this had to change
the pci driver 'remove' to release the dma resources in line with that
call instead of after all references to the device are released.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
In some cases, clear interrupt register may be at address 0.
This patch allows to use such configurations by adding additional
configuration bit to indicate this.
[With doc fix from Levente Kurusa <levex@linux.com> -- broonie]
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
For 32-bit versions of sg3-utils running on a 64-bit system. This is
mostly a copy from the relevent portions of fs/compat_ioctl.c, with
slight modifications for going through block_device_operations.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@linux.intel.com>
[fixed up CONFIG_COMPAT=n build problems]
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Whilst most IOMMU mappings should probably be non-executable, there
may be cases (HSA?) where executable mappings are required.
This patch introduces a new mapping flag, IOMMU_EXEC, to indicate that
the mapping should be mapped as executable.
Signed-off-by: Will Deacon <will.deacon@arm.com>
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=r//I
-----END PGP SIGNATURE-----
Merge tag 'ras_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/ras
Pull RAS updates from Borislav Petkov:
* Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Linux kernel has traditionally required that an UNLOCK+LOCK
pair act as a full memory barrier when either (1) that
UNLOCK+LOCK pair was executed by the same CPU or task, or (2)
the same lock variable was used for the UNLOCK and LOCK. It now
seems likely that very few places in the kernel rely on this
full-memory-barrier semantic, and with the advent of queued
locks, providing this semantic either requires complex
reasoning, or for some architectures, added overhead.
This commit therefore adds a smp_mb__after_unlock_lock(), which
may be placed after a LOCK primitive to restore the
full-memory-barrier semantic. All definitions are currently
no-ops, but will be upgraded for some architectures when queued
locks arrive.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1386799151-2219-5-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Synchronize with mainline to bring in the new keycode definitions and
new hwmon API.
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new DMA_TYPE for SSI dual FIFO script, included
in SDMA firmware version 2. This script would allow SSI use dual
fifo mode to transimit/receive data without occasional hardware
underrun/overrun.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
On i.MX5/6 series, SDMA is using new version firmware to support SSI
dual FIFO feature and HDMI Audio (i.MX6Q/DL only). Thus add it.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Pull x86 fixes from Peter Anvin:
"This is a pretty small batch:
The biggest single change is to stop using EFI time services on 32-bit
platforms. This matches our current behavior on 64-bit platforms as
we already had ruled them out there as being too unreliable. Turns
out that affects 32-bit platforms, too.
One NULL pointer fix for SGI UV.
Two minor build fixes, one of which only affects icc and the other
which affects icc and future versions or nonstandard default settings
of gcc"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Don't use (U)EFI time services on 32 bit
x86, build, icc: Remove uninitialized_var() from compiler-intel.h
x86/UV: Fix NULL pointer dereference in uv_flush_tlb_others() if the 'nobau' boot option is used
x86, build: Pass in additional -mno-mmx, -mno-sse options
The bond_first_slave_rcu() will be used to instead of bond_first_slave()
in rcu_read_lock().
According to the Jay Vosburgh's suggestion, the struct netdev_adjacent
should hide from users who wanted to use it directly. so I package a
new function to get the first slave of the bond.
Suggested-by: Nikolay Aleksandrov <nikolay@redhat.com>
Suggested-by: Jay Vosburgh <fubar@us.ibm.com>
Suggested-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer use of the direct definition of struct pci_device_id instead of
indirection via macro DEFINE_PCI_DEVICE_TABLE.
Update the PCI documentation to deprecate DEFINE_PCI_DEVICE_TABLE. Update
checkpatch adding --fix option.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
* pci/misc:
PCI: Stop clearing bridge Secondary Status when setting up I/O aperture
PCI: Prevent bus conflicts while checking for bridge apertures
PCI: Drop "irq" param from *_restore_msi_irqs()
PCI/portdrv: Remove superfluous name cast
PCI: Clear NumVFs when disabling SR-IOV in sriov_init()
The PAUSEWR and PAUSERD flags are meant to stop the cluster from
processing writes and reads, respectively. The FULL flag is set when
the cluster determines that it is out of space, and will no longer
process writes. PAUSEWR and PAUSERD are purely client-side settings
already implemented in userspace clients. The osd does nothing special
with these flags.
When the FULL flag is set, however, the osd responds to all writes
with -ENOSPC. For cephfs, this makes sense, but for rbd the block
layer translates this into EIO. If a cluster goes from full to
non-full quickly, a filesystem on top of rbd will not behave well,
since some writes succeed while others get EIO.
Fix this by blocking any writes when the FULL flag is set in the osd
client. This is the same strategy used by userspace, so apply it by
default. A follow-on patch makes this configurable.
__map_request() is called to re-target osd requests in case the
available osds changed. Add a paused field to a ceph_osd_request, and
set it whenever an appropriate osd map flag is set. Avoid queueing
paused requests in __map_request(), but force them to be resent if
they become unpaused.
Also subscribe to the next osd map from the monitor if any of these
flags are set, so paused requests can be unblocked as soon as
possible.
Fixes: http://tracker.ceph.com/issues/6079
Reviewed-by: Sage Weil <sage@inktank.com>
Signed-off-by: Josh Durgin <josh.durgin@inktank.com>
Change x86_msi.restore_msi_irqs(struct pci_dev *dev, int irq) to
x86_msi.restore_msi_irqs(struct pci_dev *dev).
restore_msi_irqs() restores multiple MSI-X IRQs, so param 'int irq' is
unneeded. This makes code more consistent between vm and bare metal.
Dom0 MSI-X restore code can also be optimized as XEN only has a hypercall
to restore all MSI-X vectors at one time.
Tested-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Since the commit 15ad7146 ("KVM: Use the scheduler preemption notifiers
to make kvm preemptible"), the remaining stuff in this function is a
simple cond_resched() call with an extra need_resched() check which was
there to avoid dropping VCPUs unnecessarily. Now it is meaningless.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:
- Fixed rate clocks with multiplier and divisor set according to boot
mode configuration
- Custom divider clocks with SoC-specific divider values
This driver supports both.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The machine cannot fault if !MUU, so make might_fault() a nop for !MMU.
This fixes below build error if
!CONFIG_MMU && (CONFIG_PROVE_LOCKING=y || CONFIG_DEBUG_ATOMIC_SLEEP=y):
arch/arm/kernel/built-in.o: In function `arch_ptrace':
arch/arm/kernel/ptrace.c:852: undefined reference to `might_fault'
arch/arm/kernel/built-in.o: In function `restore_sigframe':
arch/arm/kernel/signal.c:173: undefined reference to `might_fault'
...
arch/arm/kernel/built-in.o:arch/arm/kernel/signal.c:177: more undefined references to `might_fault' follow
make: *** [vmlinux] Error 1
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
doc.2013.12.03a: Topic branch for documentation changes.
fixes.2013.12.12a: Topic branch for miscellaneous fixes.
rcutorture.2013.12.03a: Topic branch for new rcutorture/KVM scripting.
sparse.2013.12.12a: Topic branch for sparse-RCU changes.
neigh_priv_len is defined as u8. With all debug enabled struct
ipoib_neigh has 200 bytes. The largest part is sk_buff_head with 96
bytes and here the spinlock with 72 bytes.
The size value still fits in this u8 leaving some room for more.
On -RT struct ipoib_neigh put on weight and has 392 bytes. The main
reason is sk_buff_head with 288 and the fatty here is spinlock with 192
bytes. This does no longer fit into into neigh_priv_len and gcc
complains.
This patch changes neigh_priv_len from being 8bit to 16bit. Since the
following element (dev_id) is 16bit followed by a spinlock which is
aligned, the struct remains with a total size of 3200 (allmodconfig) /
2048 (with as much debug off as possible) bytes on x86-64.
On x86-32 the struct is 1856 (allmodconfig) / 1216 (with as much debug
off as possible) bytes long. The numbers were gained with and without
the patch to prove that this change does not increase the size of the
struct.
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function prototypes don't need to have the "extern" keyword since this
is the default behavior. Its explicit use is redundant. This commit
therefore removes them.
Signed-off-by: Teodora Baluta <teobaluta@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
There is currently no way to initialize a global RCU-protected pointer
without either putting up with sparse complaints or open-coding an
obscure cast. This commit therefore creates RCU_INITIALIZER(), which
is intended to be used as follows:
struct foo __rcu *p = RCU_INITIALIZER(&my_rcu_structure);
This commit also applies RCU_INITIALIZER() to eliminate repeated
open-coded obscure casts in __rcu_assign_pointer(), RCU_INIT_POINTER(),
and RCU_POINTER_INITIALIZER(). This commit also inlines
__rcu_assign_pointer() into its only caller, rcu_assign_pointer().
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu_assign_pointer() primitive needs to use ACCESS_ONCE to make
the assignment to the destination pointer volatile, to protect against
compilers too clever for their own good.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The rcu_assign_pointer() macro, as with most cpp macros, must not evaluate
its argument more than once. And it in fact does not. But this might
not be obvious to the casual observer, because one of the arguments
appears no less than three times. However, but one expansion is only
visible to sparse (__CHECKER__), and one lives inside a typeof (where
it will never be evaluated), so this is in fact safe.
This commit therefore adds a comment making this explicit.
Reported-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
There are no old function interface users left, so the old interface can
be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is required in order to integrate configfs support.
f_fs needs to be a separately compiled module and so it needs to use the new
interface.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will be required in order to use the new function interface
(usb_get_function_instance/usb_put_function_instance)
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyunmgin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB function's configfs config group is created in a generic way in
usb/gadget/configfs.c:function_make(), which in turn delegates actual
allocation and setup of the USB function instance to a particular
implementation, e.g. in f_acm.c. The said implementation does its job
in a parameter-less function e.g. acm_alloc_instance(), which results
in creating an unnamed config group, whose name is set later in
function_make(). function_make() creates the name by parsing a string
of the form:
<function name>.<instance name>
which comes from userspace as a parameter to mkdir invocation.
Up to now only <function name> has been used, while <instance name>
has been ignored. This patch adds a set_inst_name() operation to
struct usb_function_instance which allows passing the <instance name>
from function_make() so that it is not ignored. It is entirely up to the
implementor of set_inst_name() what to do with the <instance name>.
In a typical case, the struct usb_function_instance is embedded in a
larger struct which is retrieved in set_inst_name() with container_of(),
and the larger struct contains a field to store the <instance name>.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch modifies the GRO stack to avoid the use of "network_header"
and associated macros like ip_hdr() and ipv6_hdr() in order to allow
an arbitary number of IP hdrs (v4 or v6) to be used in the
encapsulation chain. This lays the foundation for various IP
tunneling support (IP-in-IP, GRE, VXLAN, SIT,...) to be added later.
With this patch, the GRO stack traversing now is mostly based on
skb_gro_offset rather than special hdr offsets saved in skb (e.g.,
skb->network_header). As a result all but the top layer (i.e., the
the transport layer) must have hdrs of the same length in order for
a pkt to be considered for aggregation. Therefore when adding a new
encap layer (e.g., for tunneling), one must check and skip flows
(e.g., by setting NAPI_GRO_CB(p)->same_flow to 0) that have a
different hdr length.
Note that unlike the network header, the transport header can and
will continue to be set by the GRO code since there will be at
most one "transport layer" in the encap chain.
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When explicitly hashing the end of a string with the word-at-a-time
interface, we have to be careful which end of the word we pick up.
On big-endian CPUs, the upper-bits will contain the data we're after, so
ensure we generate our masks accordingly (and avoid hashing whatever
random junk may have been sitting after the string).
This patch adds a new dcache helper, bytemask_from_count, which creates
a mask appropriate for the CPU endianness.
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since now macvlan and macvtap use the same receive and
forward handlers, we can remove them completely and use
netif_rx and dev_forward_skb() directly.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIVAwUAUqdgihOxKuMESys7AQIishAAjGG3LnEp12fd7oay5//4SEg31ybPqGj7
Xotk9mblBW7cWPbLqk7xyIhxpIj2zM14XatEV2TfBNZV0Lcrzr1M5s87ZRUX0ui+
FHbtfn/M3Or8AvX7W1HZgG2Se7M0Ba6Y2RRXNsEdgqk6KMQuHhPEZ2FZ5vCx6BAD
vXzxWIKVNeqMXR7z6xkyqmpztnVQs+ZgzE9+c96QKyhBdtBy4spDmfgJS90m0pjN
HhgONpdfgosknj8yu43rWIQvd3UUO5BVntCeic94Fbgh77ZAEi0dD7ifLz/ebcja
pfJfPXxYzkCfIrSdAzQF8iYnQ+5rRomvGsMcvtq6mBooah/YmEkmKpKJDTp47wyN
IEUeJaxM2Qp2jcUSjEd7lY9o1AK4sj+90cKeVRUd5kzZP1iolkQHR+dGiAwqbn6w
MJBn9fCamvhpsZDhl2G/DICprFDvErd9zAlNubivggJmITnPXNWx+K1RDL4fO4qc
zLHTGHkxYyACM/7oJfwbH/NyZ1yu53OlE3R2h6TA6ISc7nAed7qzGAZyrSV92Quc
pItGaQ/zNa0sbe+nufCx9FOWu8sA3x7qnazLxhVtlPde9nlxcpGo5cagqcyc4hyp
/IGK2JoGkgHvehECY8miJlsu7UqmThIhmy6o4T4X6ErX1M9ifR92WGeXkAi/2mh/
WciVpPvTrqM=
=/AdA
-----END PGP SIGNATURE-----
Merge tag 'keys-devel-20131210' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull misc keyrings fixes from David Howells:
"These break down into five sets:
- A patch to error handling in the big_key type for huge payloads.
If the payload is larger than the "low limit" and the backing store
allocation fails, then big_key_instantiate() doesn't clear the
payload pointers in the key, assuming them to have been previously
cleared - but only one of them is.
Unfortunately, the garbage collector still calls big_key_destroy()
when sees one of the pointers with a weird value in it (and not
NULL) which it then tries to clean up.
- Three patches to fix the keyring type:
* A patch to fix the hash function to correctly divide keyrings off
from keys in the topology of the tree inside the associative
array. This is only a problem if searching through nested
keyrings - and only if the hash function incorrectly puts the a
keyring outside of the 0 branch of the root node.
* A patch to fix keyrings' use of the associative array. The
__key_link_begin() function initially passes a NULL key pointer
to assoc_array_insert() on the basis that it's holding a place in
the tree whilst it does more allocation and stuff.
This is only a problem when a node contains 16 keys that match at
that level and we want to add an also matching 17th. This should
easily be manufactured with a keyring full of keyrings (without
chucking any other sort of key into the mix) - except for (a)
above which makes it on average adding the 65th keyring.
* A patch to fix searching down through nested keyrings, where any
keyring in the set has more than 16 keyrings and none of the
first keyrings we look through has a match (before the tree
iteration needs to step to a more distal node).
Test in keyutils test suite:
http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=8b4ae963ed92523aea18dfbb8cab3f4979e13bd1
- A patch to fix the big_key type's use of a shmem file as its
backing store causing audit messages and LSM check failures. This
is done by setting S_PRIVATE on the file to avoid LSM checks on the
file (access to the shmem file goes through the keyctl() interface
and so is gated by the LSM that way).
This isn't normally a problem if a key is used by the context that
generated it - and it's currently only used by libkrb5.
Test in keyutils test suite:
http://git.kernel.org/cgit/linux/kernel/git/dhowells/keyutils.git/commit/?id=d9a53cbab42c293962f2f78f7190253fc73bd32e
- A patch to add a generated file to .gitignore.
- A patch to fix the alignment of the system certificate data such
that it it works on s390. As I understand it, on the S390 arch,
symbols must be 2-byte aligned because loading the address discards
the least-significant bit"
* tag 'keys-devel-20131210' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
KEYS: correct alignment of system_certificate_list content in assembly file
Ignore generated file kernel/x509_certificate_list
security: shmem: implement kernel private shmem inodes
KEYS: Fix searching of nested keyrings
KEYS: Fix multiple key add into associative array
KEYS: Fix the keyring hash function
KEYS: Pre-clear struct key on allocation
Commit 20bc4d5d56
(gpio: 74x164: Add support for the daisy-chaining) introduce check
for DT for the driver, so driver cannot be used without DT.
There are no in-tree users of this driver, so remove non-DT support
completely.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/SYSFS_DIR/KERNFS_DIR/
* s/SYSFS_KOBJ_ATTR/KERNFS_FILE/
* s/SYSFS_KOBJ_LINK/KERNFS_LINK/
* s/SYSFS_{TYPE_FLAGS}/KERNFS_{TYPE_FLAGS}/
* s/SYSFS_FLAG_{FLAG}/KERNFS_{FLAG}/
* s/sysfs_type()/kernfs_type()/
* s/SD_DEACTIVATED_BIAS/KN_DEACTIVATED_BIAS/
This patch is strictly rename only and doesn't introduce any
functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/sysfs_open_dirent/kernfs_open_node/
* s/sysfs_open_file/kernfs_open_file/
* s/sysfs_inode_attrs/kernfs_iattrs/
* s/sysfs_addrm_cxt/kernfs_addrm_cxt/
* s/sysfs_super_info/kernfs_super_info/
* s/sysfs_info()/kernfs_info()/
* s/sysfs_open_dirent_lock/kernfs_open_node_lock/
* s/sysfs_open_file_mutex/kernfs_open_file_mutex/
* s/sysfs_of()/kernfs_of()/
This patch is strictly rename only and doesn't introduce any
functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that no code uses the custom Tegra module reset API, we can remove
its implementation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-By: Peter De Schrijver <pdeschrijver@nvidia.com>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
s_ prefix for kernfs members is used inconsistently and a misnomer
now. It's not like kernfs_node is used widely across the kernel
making the ability to grep for the members particularly useful. Let's
just drop the prefix.
This patch is strictly rename only and doesn't introduce any
functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
kernfs has just been separated out from sysfs and we're already in
full conflict mode. Nothing can make the situation any worse. Let's
take the chance to name things properly.
This patch performs the following renames.
* s/sysfs_elem_dir/kernfs_elem_dir/
* s/sysfs_elem_symlink/kernfs_elem_symlink/
* s/sysfs_elem_attr/kernfs_elem_file/
* s/sysfs_dirent/kernfs_node/
* s/sd/kn/ in kernfs proper
* s/parent_sd/parent/
* s/target_sd/target/
* s/dir_sd/parent/
* s/to_sysfs_dirent()/rb_to_kn()/
* misc renames of local vars when they conflict with the above
Because md, mic and gpio dig into sysfs details, this patch ends up
modifying them. All are sysfs_dirent renames and trivial. While we
can avoid these by introducing a dummy wrapping struct sysfs_dirent
around kernfs_node, given the limited usage outside kernfs and sysfs
proper, I don't think such workaround is called for.
This patch is strictly rename only and doesn't introduce any
functional difference.
- mic / gpio renames were missing. Spotted by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace hard-coded value for mask used in BUCKX_CTRL registers (for
BUCKX_EN field) with a symbol. This also removes two local variables.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Help of this function says: "in_dev: only on this interface, 0=any interface",
but since commit 39a6d06300 ("[NETNS]: Process inet_confirm_addr in the
correct namespace."), the code supposes that it will never be NULL. This
function is never called with in_dev == NULL, but it's exported and may be used
by an external module.
Because this patch restore the ability to call inet_confirm_addr() with in_dev
== NULL, I partially revert the above commit, as suggested by Julian.
CC: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas R-Car development boards use KSZ8041RNLI PHY which for some reason has
ID of 0x00221537 that is not documented for KSZ8041-family PHYs and does not
match the documented ID of 0x0022151x (where 'x' is the revision). We have
to add the new #define PHY_ID_* and new ksphy_driver[] entry, almost the same
as KSZ8041 one, differing only in the 'phy_id' and 'name' fields.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new parameter is used to control how to report HW error reporting,
especially for newer Intel platform, like Ivybridge-EX, which contains
an enhanced error decoding functionality in the firmware, i.e. eMCA.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1386310630-12529-2-git-send-email-gong.chen@linux.intel.com
[ Boris: massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: linux-wireless@vger.kernel.org
CC: Lauro Ramos Venancio <lauro.venancio@openbossa.org>
CC: Aloisio Almeida Jr <aloisio.almeida@openbossa.org>
CC: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Christian suffers from a bad BIOS that wrecks his i5's TSC sync. This
results in him occasionally seeing time going backwards - which
crashes the scheduler ...
Most of our time accounting can actually handle that except the most
common one; the tick time update of sched_fair.
There is a further problem with that code; previously we assumed that
because we get a tick every TICK_NSEC our time delta could never
exceed 32bits and math was simpler.
However, ever since Frederic managed to get NO_HZ_FULL merged; this is
no longer the case since now a task can run for a long time indeed
without getting a tick. It only takes about ~4.2 seconds to overflow
our u32 in nanoseconds.
This means we not only need to better deal with time going backwards;
but also means we need to be able to deal with large deltas.
This patch reworks the entire code and uses mul_u64_u32_shr() as
proposed by Andy a long while ago.
We express our virtual time scale factor in a u32 multiplier and shift
right and the 32bit mul_u64_u32_shr() implementation reduces to a
single 32x32->64 multiply if the time delta is still short (common
case).
For 64bit a 64x64->128 multiply can be used if ARCH_SUPPORTS_INT128.
Reported-and-Tested-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
Cc: Paul Turner <pjt@google.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131118172706.GI3866@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Introduce mul_u64_u32_shr() as proposed by Andy a while back; it
allows using 64x64->128 muls on 64bit archs and recent GCC
which defines __SIZEOF_INT128__ and __int128.
(This new method will be used by the scheduler.)
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: fweisbec@gmail.com
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-hxjoeuzmrcaumR0uZwjpe2pv@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
While hunting a preemption issue with Alexander, Ben noticed that the
currently generic PREEMPT_NEED_RESCHED stuff is horribly broken for
load-store architectures.
We currently rely on the IPI to fold TIF_NEED_RESCHED into
PREEMPT_NEED_RESCHED, but when this IPI lands while we already have
a load for the preempt-count but before the store, the store will erase
the PREEMPT_NEED_RESCHED change.
The current preempt-count only works on load-store archs because
interrupts are assumed to be completely balanced wrt their preempt_count
fiddling; the previous preempt_count load will match the preempt_count
state after the interrupt and therefore nothing gets lost.
This patch removes the PREEMPT_NEED_RESCHED usage from generic code and
pushes it into x86 arch code; the generic code goes back to relying on
TIF_NEED_RESCHED.
Boot tested on x86_64 and compile tested on ppc64.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-and-Tested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131128132641.GP10022@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Look-Up Table looks up values in 8-bit indexed tables separately for
each color component.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Super Resolution Unit performs super resolution processing with
optional upscaling by a factor of two.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add missing initcall variants when building for loadable modules.
This fixes this build error on powerpc allmodconfig:
drivers/tty/ehv_bytechan.c: error: type defaults to 'int' in declaration of 'console_initcall' [-Werror=implicit-int]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIPC is currently using the field 'af_packet_priv' in struct net_device
as a handle to find the bearer instance associated to the given network
device. But, by doing so it is blocking other networking cleanups, such
as the one discussed here:
http://patchwork.ozlabs.org/patch/178044/
This commit removes this usage from TIPC. Instead, we introduce a new
field, 'tipc_ptr', to the net_device structure, to serve this purpose.
When TIPC bearer is enabled, the bearer object is associated to
'tipc_ptr'. When a TIPC packet arrives in the recv_msg() upcall
from a networking device, the bearer object can now be obtained from
'tipc_ptr'. When a bearer is disabled, the bearer object is detached
from its underlying network device by setting 'tipc_ptr' to NULL.
Additionally, an RCU lock is used to protect the new pointer.
Henceforth, the existing tipc_net_lock is used in write mode to
serialize write accesses to this pointer, while the new RCU lock is
applied on the read side to ensure that the pointer is 100% valid
within its wrapped area for all readers.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
unix_dgram_recvmsg() will hold the readlock of the socket until recv
is complete.
In the same time, we may try to setsockopt(SO_PEEK_OFF) which will hang until
unix_dgram_recvmsg() will complete (which can take a while) without allowing
us to break out of it, triggering a hung task spew.
Instead, allow set_peek_off to fail, this way userspace will not hang.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compiling with icc, <linux/compiler-gcc.h> ends up included
because the icc environment defines __GNUC__. Thus, we neither need
nor want to have this macro defined in both compiler-gcc.h and
compiler-intel.h, and the fact that they are inconsistent just makes
the compiler spew warnings.
Reported-by: Sunil K. Pandey <sunil.k.pandey@intel.com>
Cc: Kevin B. Smith <kevin.b.smith@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/n/tip-0mbwou1zt7pafij09b897lg3@git.kernel.org
Cc: <stable@vger.kernel.org>
Change the default enumeration scheme for xhci attached non-SuperSpeed
devices from:
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(8)
GetDescriptor(18)
...to:
Reset
[xhci address-device BSR = 1]
GetDescriptor(64)
Reset
SetAddress [xhci address-device BSR = 0]
GetDescriptor(18)
...as some devices misbehave when encountering a SetAddress command
prior to GetDescriptor. There are known legacy devices that require
this scheme, but testing has found at least one USB3 device that fails
enumeration when presented with this ordering. For now, follow the ehci
case and enable 'new scheme' by default for non-SuperSpeed devices.
To support this enumeration scheme on xhci the AddressDevice operation
needs to be performed twice. The first instance of the command enables
the HC's device and slot context info for the device, but omits sending
the device a SetAddress command (BSR == block set address request).
Then, after GetDescriptor completes, follow up with the full
AddressDevice+SetAddress operation.
As mentioned before, this ordering of events with USB3 devices causes an
extra state transition to be exposed to xhci. Previously USB3 devices
would transition directly from 'enabled' to 'addressed' and never need
to underrun responses to 'get descriptor'. We do see the 64-byte
descriptor fetch the correct data, but the following 18-byte descriptor
read after the reset gets:
bLength = 0
bDescriptorType = 0
bcdUSB = 0
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
instead of:
bLength = 12
bDescriptorType = 1
bcdUSB = 300
bDeviceClass = 0
bDeviceSubClass = 0
bDeviceProtocol = 0
bMaxPacketSize0 = 9
which results in the discovery process looping until falling back to
'old scheme' enumeration.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: David Moore <david.moore@gmail.com>
Suggested-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
a8b1474442 ("sysfs: give different locking key to regular and bin
files") in driver-core-linus modifies sysfs_open_file() so that it
gives out different locking classes to sysfs_open_files depending on
whether the file is bin or not. Due to the massive kernfs
reorganization in driver-core-next, this naturally causes merge
conflict in fs/sysfs/file.c.
Due to the way things are split between kernfs and sysfs in
driver-core-next, the same fix can't easily be applied to
driver-core-next. This merge simply ignores the offending commit. A
following patch will implement a separate fix for the issue.
Signed-off-by: Tejun Heo <tj@kernel.org>
mmp_pdma.c implements a custom of_xlate() function that is 95% identical
to what Tegra will need. Create a function to implement the common part,
so everyone doesn't just cut/paste the implementation.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
dma_request_slave_channel() simply returns NULL whenever DMA channel
lookup fails. Lookup could fail for two distinct reasons:
a) No DMA specification exists for the channel name.
This includes situations where no DMA specifications exist at all, or
other general lookup problems.
b) A DMA specification does exist, yet the driver for that channel is not
yet registered.
Case (b) should trigger deferred probe in client drivers. However, since
they have no way to differentiate the two situations, it cannot.
Implement new function dma_request_slave_channel_reason(), which performs
identically to dma_request_slave_channel(), except that it returns an
error-pointer rather than NULL, which allows callers to detect when
deferred probe should occur.
Eventually, all drivers should be converted to this new API, the old API
removed, and the new API renamed to the more desirable name. This patch
doesn't convert the existing API and all drivers in one go, since some
drivers call dma_request_slave_channel() then dma_request_channel() if
that fails. That would require either modifying dma_request_channel() in
the same way, or adding extra error-handling code to all affected
drivers, and there are close to 100 drivers using the other API, rather
than just the 15-20 or so that use dma_request_slave_channel(), which
might be tenable in a single patch.
acpi_dma_request_slave_chan_by_name() doesn't currently implement
deferred probe. It should, but this will be addressed later.
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
The IP in DRA7xx is similar to the IP found in TI81xxAM3xxx/AM4xxx type of
SoCs but it is is integrated with sDMA instead of eDMA. The suitable pcm
driver for DRA7xx is the omap-pcm driver which is using dmaengine.
In the driver we can configure both dma related structures used for eDMA and
sDMA. The only thing we need to make sure that we set the correct dma_data
at startup with snd_soc_dai_set_dma_data()
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Due to USB controllers may have different restrictions, usb gadget layer
needs to provide a generic way to inform gadget functions to complain
with non-standard requirements.
This patch adds 'quirk_ep_out_aligned_size' field to struct usb_gadget
to inform when controller's epout requires buffer size to be aligned to
MaxPacketSize. A helper is also provided to align buffer size when
necessary.
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves all bitflags to the end of usb_gadget struct in order
to improve readability.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
tclass information in now already stored in rcv_flowinfo
We do not need to store the same information twice.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current implementation of IPV6_FLOWINFO only gives a
result if pktoptions is available (thanks to the
ip6_datagram_recv_ctl function).
It gives inconsistent results to user space, sometimes
there is a result for getsockopt(IPV6_FLOWINFO), sometimes
not.
This patch add rcv_flowinfo to store it, and return it to
the userspace in the same way than other pkt_options.
Signed-off-by: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set,
several is_<foo>_ether_addr functions can be slightly
improved by using u32 dereferences.
I believe all current uses of is_zero_ether_addr and
is_broadcast_ether_addr are u16 aligned, so always use
u16 references to improve those functions performance.
Document the u16 alignment requirements.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a generic routine to test if possibly unaligned
to u16 Ethernet addresses are equal.
If CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is set,
this uses the slightly faster generic routine
ether_addr_equal, otherwise this uses memcmp.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously inet devices were only constructed when addresses are added.
Therefore the default neigh parms values they get are the ones at the
time of these operations.
Now that we're creating inet devices earlier, this changes the behaviour
of default neigh parms values in an incompatible way (see bug #8519).
This patch creates a compromise by setting the default values at the
same point as before but only for those that have not been explicitly
set by the user since the inet device's creation.
Introduced by:
commit 8030f54499
Author: Herbert Xu <herbert@gondor.apana.org.au>
Date: Thu Feb 22 01:53:47 2007 +0900
[IPV4] devinet: Register inetdev earlier.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library already reads the MII_STAT1000 and MII_LPA registers in
genphy_read_status(), so extend it to also populate the PHY device link
partner advertised features such that we can feed this back into ethtool
when asked for it in phy_ethtool_gset().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we need it elsewhere, move the inline helper function of
skb_needs_linearize() over to skbuff.h include file. While
at it, also convert the return to 'bool' instead of 'int'
and add a proper kernel doc.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge 'net' into 'net-next' to get the AF_PACKET bug fix that
Daniel's direct transmit changes depend upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently blocking in an RCU callback function will result in
"scheduling while atomic", which could be triggered for any number
of reasons. To aid debugging, this patch introduces a rcu_callback_map
that is used to tie the inappropriate voluntary context switch back
to the fact that the function is being invoked from within a callback.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
The Buffalo device WZR-HP-G450H uses the index 3 for TX gain,
which is set to the high_power table currently. Later variants
of the router use the same index, but instead refer to the
low_ob_db gain table. This is not handled in the driver since
there is no way to distinguish board revisions and the high_power
table is used (incorrectly) for the newer variants.
By default, devices based on AR9300 using the TX gain index 3 have
to use the high_power table. To make sure that WZR-HP-G450H is not
broken when the high_power table is updated, use a separate array
based on information obtained from the platform data.
The current situation where only the original variant of WZR-HP-G450H
works properly stays unchanged.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tty flip buffers use GFP_ATOMIC allocations for received data
which is to be processed by the line discipline. For each byte
received, an extra byte is used to indicate the error status of
that byte.
Instead, if the received data is error-free, encode the entire
buffer without status bytes.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts two cpufreq commits that fixed issues for some people,
but broke things for others, so revert them and we'll need to fix the
original problems differently.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=OpKD
-----END PGP SIGNATURE-----
Merge tag 'pm-3.13-rc3-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixup from Rafael Wysocki:
"This reverts two cpufreq commits that fixed issues for some people,
but broke things for others, so revert them and we'll need to fix the
original problems differently"
* tag 'pm-3.13-rc3-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Revert "cpufreq: fix garbage kobjects on errors during suspend/resume"
Revert "cpufreq: suspend governors on system suspend/hibernate"
The patch moves description of the fields to the top of struct definition and
converts them to the kernel-doc format.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change the format of the platform GPIO lookup tables to make them less
confusing and improve lookup efficiency.
The previous format was a single linked-list that required to compare
the device name and function ID of every single GPIO defined for each
lookup. Switch that to a list of per-device tables, so that the lookup
can be done in two steps, omitting the GPIOs that are not relevant for a
particular device.
The matching rules are now defined as follows:
- The device name must match *exactly*, and can be NULL for GPIOs not
assigned to a particular device,
- If the function ID in the lookup table is NULL, the con_id argument of
gpiod_get() will not be used for lookup. However, if it is defined, it
must match exactly.
- The index must always match.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here are some bugfixes for the staging and IIO drivers for 3.13-rc3.
The resolve the vm memory issue in the tidspbridge driver, fix a much-reported
build failure in an ARM driver, and some other IIO bugfixes that have been
reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlKiFYcACgkQMUfUDdst+ykuUgCcCqLrTpaBhOfFaLhSUONJh0Db
BfYAoMFoyviPqclR7NYouZT6mUehiJ7+
=X5WP
-----END PGP SIGNATURE-----
Merge tag 'staging-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are some bugfixes for the staging and IIO drivers for 3.13-rc3.
The resolve the vm memory issue in the tidspbridge driver, fix a
much-reported build failure in an ARM driver, and some other IIO
bugfixes that have been reported"
* tag 'staging-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: TIDSPBRIDGE: Use vm_iomap_memory for mmap-ing instead of remap_pfn_range
Fix build failure for gp2ap020a00f.c
iio: hid-sensors: Fix power and report state
HID: hid-sensor-hub: Add logical min and max
Here are a bunch of USB fixes for 3.13-rc3.
Nothing major, but we seem to have an argument about a XHCI fix, so I'm not
including a revert that Sarah requested, because that breaks a USB network
driver, and I can't revert the USB network driver fix without reintroducing
other bugs that it fixed. So as it is, everything should now be
working. Worse case, I can revert the XHCI fix before 3.13-final is
out, but it seems to work well here with my testing, so all should be
good.
Other than that, some driver updates based on reports.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlKiEuYACgkQMUfUDdst+ymE8ACgnDT8s4FtrYfoyOo5K4TVTRaZ
S2wAn3+Xa2TX1Sym+ltJry7N1jRnY2Qy
=JUaB
-----END PGP SIGNATURE-----
Merge tag 'usb-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a bunch of USB fixes for 3.13-rc3.
Nothing major, but we seem to have an argument about a XHCI fix, so
I'm not including a revert that Sarah requested, because that breaks a
USB network driver, and I can't revert the USB network driver fix
without reintroducing other bugs that it fixed. So as it is,
everything should now be working. Worse case, I can revert the XHCI
fix before 3.13-final is out, but it seems to work well here with my
testing, so all should be good.
Other than that, some driver updates based on reports"
* tag 'usb-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (40 commits)
usb: hub: Use correct reset for wedged USB3 devices that are NOTATTACHED
usb: ohci-pxa27x: include linux/dma-mapping.h
USB: cdc-acm: Added support for the Lenovo RD02-D400 USB Modem
usb: tools: fix a regression issue that gcc can't link to pthread
USB: switch maintainership of chipidea to Peter
USB: pl2303: fixed handling of CS5 setting
USB: ftdi_sio: fixed handling of unsupported CSIZE setting
USB: mos7840: correct handling of CS5 setting
USB: spcp8x5: correct handling of CS5 setting
usb: wusbcore: fix deadlock in wusbhc_gtk_rekey
usb: wusbcore: do device lookup while holding the hc mutex
usb: wusbcore: send keepalives to unauthenticated devices
USB: option: support new huawei devices
USB: serial: option: blacklist interface 1 for Huawei E173s-6
usb: xhci: Link TRB must not occur within a USB payload burst
usb: gadget: f_mass_storage: call try_to_freeze only when its safe
usb: gadget: tcm_usb_gadget: mark bot_cleanup_old_alt static
usb: gadget: ffs: fix sparse warning
usb: gadget: zero: module parameters can be static
usb: gadget: storage: fix sparse warning
...
When CONFIG_FW_LOADER_USER_HELPER is set, request_firmware() falls
back to the usermode helper for loading via udev when the direct
loading fails. But the recent udev takes way too long timeout (60
seconds) for non-existing firmware. This is unacceptable for the
drivers like microcode loader where they load firmwares optionally,
i.e. it's no error even if no requested file exists.
This patch provides a new helper function, request_firmware_direct().
It behaves as same as request_firmware() except for that it doesn't
fall back to usermode helper but returns an error immediately if the
f/w can't be loaded directly in kernel.
Without CONFIG_FW_LOADER_USER_HELPER=y, request_firmware_direct() is
just an alias of request_firmware(), due to obvious reason.
Tested-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use PCI standard marco dev_is_pci() instead of directly compare
pci_bus_type to check whether it is pci device.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds remove_phy flag to the HCD structure. If the flag is
set and if hcd->phy is valid, the phy is shutdown and released
whenever usb_add_hcd fails or usb_hcd_remove is called.
This can be used by the HCD drivers to auto-remove
the external USB phy when it is no longer needed.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sg_copy_buffer() can't meet demand for some drrivers(such usb
mass storage), so we have to use the sg_miter_* APIs to access
sg buffer, then need export sg_miter_skip() for these drivers.
The API is needed for converting to sg_miter_* APIs in USB storage
driver for accessing sg buffer.
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add mx6 hdmi transmitter support.
Original work has been done by Sascha Hauer and Tony Prisk.
Special thanks to Russell King for his carefully review, many bug fixes and
testing of the mx6 HDMI driver.
Tested on the following boards:
- mx6q sabresd
- mx6dl sabresd
- mx6solo wandboard
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Making DMA RX polling optional when DMA is on was just
over-cautious: there is one single system in the kernel tree
using this facility, Ux500 and after some testing I turned
this on also for Ux500, which means it should simply be on
by default if DMA is enabled.
Cc: Jongsung Kim <neidhard.kim@lge.com>
Cc: Chanho Min <chanho.min@lge.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no in-tree user of tty_prepare_flip_string_flags(); remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trim up the memory_used field name to mem_used.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow driver to configure its maximum flip buffer memory
consumption/limit. This is necessary for very-high speed line
rates (in excess of 10MB/sec) because the flip buffers can
be saturated before the line discipline has a chance to
throttle the input.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most line disciplines already handle the undocumented NULL flag
ptr in their .receive_buf method; however, several don't.
Document the NULL flag ptr, and correct handling in the
N_MOUSE, N_GSM0710 and N_R394 line disciplines.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
change_prot_numa should work even if _PAGE_NUMA != _PAGE_PROTNONE.
On archs like ppc64 that don't use _PAGE_PROTNONE and also have
a separate page table outside linux pagetable, we just need to
make sure that when calling change_prot_numa we flush the
hardware page table entry so that next page access result in a numa
fault.
We still need to make sure we use the numa faulting logic only
when CONFIG_NUMA_BALANCING is set. This implies the migrate-on-fault
(Lazy migration) via mbind will only work if CONFIG_NUMA_BALANCING
is set.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Now that all drivers have been converted to the new event config interface we
can remove for the legacy event config interface. Also drop the '_new' suffix
for the event config interface callbacks, since those are the only callbacks
now.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 5a87182aa2 (cpufreq: suspend governors on system
suspend/hibernate) causes hibernation problems to happen on
Bjørn Mork's and Paul Bolle's systems, so revert it.
Fixes: 5a87182aa2 (cpufreq: suspend governors on system suspend/hibernate)
Reported-by: Bjørn Mork <bjorn@mork.no>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a flag to tell the PCI subsystem that kernel is shutting down in
preparation to kexec a kernel. Add code in PCI subsystem to use this flag
to clear Bus Master bit on PCI devices only in case of kexec reboot.
This fixes a power-off problem on Acer Aspire V5-573G and likely other
machines and avoids any other issues caused by clearing Bus Master bit on
PCI devices in normal shutdown path. The problem was introduced by
b566a22c23 ("PCI: disable Bus Master on PCI device shutdown").
This patch is based on discussion at
http://marc.info/?l=linux-pci&m=138425645204355&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63861
Reported-by: Chang Liu <cl91tp@gmail.com>
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: stable@vger.kernel.org # v3.5+
To avoid build problems and breaking dependencies between ACPI header
files, <acpi/acpi.h> should not be included directly by code outside
of the ACPI core subsystem, but this is done by the ACPI iSCSI
Boot Firmware code.
The iBFT specification doesn't mention whether or not it can appear
on a non-ACPI platform, but is says that ACPI 3.0b defines the
mechanism. The current CONFIG_ISCSI_IBFT_FIND code doesn't use the
ACPI tables API to locate the table, so it doesn't rely on CONFIG_ACPI
directly.
However, since iBFT is is an ACPI-based mechanism (please refer to
the documentation link below for more information), it should be
correct to make CONFIG_ISCSI_IBFT_FIND depend on CONFIG_ACPI (even
though the table location can be implemented without using ACPI
tables API).
After that change, include/linux/iscsi_ibft.h can be modified to
include <linux/acpi.h> instead of <acpi/acpi.h> as appropriate.
References: http://www.microsoft.com/whdc/system/platform/firmware/ibft.mspx
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Peter Jones <pjones@redhat.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To avoid build problems and breaking dependencies between ACPI header
files, <acpi/acpi.h> should not be included directly by code outside
of the ACPI core subsystem. However, that is possible if
<linux/acpi_io.h> is included, because that file contains
a direct inclusion of <acpi/acpi.h>.
For this reason, remove the direct <acpi/acpi.h> inclusion from
<linux/acpi_io.h>, move that file from include/linux/ to include/acpi/
and make <linux/acpi.h> include it for CONFIG_ACPI set along with the
other ACPI header files. Accordingly, Remove the inclusions of
<linux/acpi_io.h> from everywhere.
Of course, that causes the contents of the new <acpi/acpi_io.h> file
to be available for CONFIG_ACPI set only, so intel_opregion.o that
depends on it should also depend on CONFIG_ACPI (and it really should
not be compiled for CONFIG_ACPI unset anyway).
References: https://01.org/linuxgraphics/sites/default/files/documentation/acpi_igd_opregion_spec.pdf
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following warnings can be seen in W=1 builds, because the original
sfi_acpi.[ch] header inclusions are incorrect:
include/linux/sfi_acpi.h:72:2: error: implicit declaration of function 'acpi_table_parse' [-Werror=implicit-function-declaration]
drivers/sfi/sfi_acpi.c:154:5: warning: no previous prototype for 'sfi_acpi_table_parse' [-Wmissing-prototypes]
Fix linux/sfi_acpi.h and modify drivers/sfi/sfi_acpi.c accordingly.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[rjw: Subject and changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify acpi_preset_companion() to take a struct acpi_device pointer
instead of an ACPI handle as its second argument and redefine it as
a static inline wrapper around ACPI_COMPANION_SET() passing the
return value of acpi_find_child_device() directly as the second
argument to it. Update its users to pass struct acpi_device
pointers instead of ACPI handles to it.
This allows some unnecessary acpi_bus_get_device() calls to be
avoided.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Aaron Lu <aaron.lu@intel.com> # for ATA binding
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.
First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds. For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.
Second, there are ordering dependencies between those files that always
have to be met. Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there. And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds. That also is taken care of including
<linux/acpi.h> as appropriate.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a new check for CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS to reduce
the number of or's used in the ether_addr_equal comparison to very
slightly improve function performance.
Simplify the ether_addr_equal_64bits implementation.
Integrate and remove the zap_last_2bytes helper as it's now
used only once.
Remove the now unused compare_ether_addr function.
Update the unaligned-memory-access documentation to remove the
compare_ether_addr description and show how unaligned accesses
could occur with ether_addr_equal.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move omap_usb_config to platform data, so that OTG driver can include it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some network drivers use dev_kfree_skb_any() and dev_kfree_skb_irq()
helpers to free skbs, both for dropped packets and TX completed ones.
We need to separate the two causes to get better diagnostics
given by dropwatch or "perf record -e skb:kfree_skb"
This patch provides two new helpers, dev_consume_skb_any() and
dev_consume_skb_irq() to be used for consumed skbs.
__dev_kfree_skb_irq() is slightly optimized to remove one
atomic_dec_and_test() in fast path, and use this_cpu_{r|w} accessors.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous patch which introduced for_each_css(),
for_each_root_subsys() only has two users left. This patch replaces
it with for_each_subsys() + explicit subsys_mask testing and remove
for_each_root_subsys() along with cgroupfs_root->subsys_list handling.
This patch doesn't introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Breakdown the PHY_*_FEATURES into per speed defines such that we can
easily re-use them individually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
Please pull this batch of updates intended for the 3.14 stream...
For the mac80211 bits, Johannes says:
"I have various improvements/cleanups/fixes all over, but the shortlog
shows that Luis's regulatory work and mesh work from the cozybit folks
are the biggest ones, along with the CSA fixes."
Along with that, we have big batches of updates to brcmfmac, rtlwifi,
and ath9k. There are updates to wcn36xx, rt2x00, and a handful of
others as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a more reliable method to tell if gssd is running, we
can replace the sn->gssd_running flag with a function that will query to
see if it's up and running.
There's also no need to attempt an upcall that we know will fail, so
just return -EACCES if gssd isn't running. Finally, fix the warn_gss()
message not to claim that that the upcall timed out since we don't
necesarily perform one now when gssd isn't running, and remove the
extraneous newline from the message.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
rpc.gssd will naturally hold open any pipe named */clnt*/gssd that shows
up under rpc_pipefs. That behavior gives us a reliable mechanism to tell
whether it's actually running or not.
Create a new toplevel "gssd" directory in rpc_pipefs when it's mounted.
Under that directory create another directory called "clntXX", and then
within that a pipe called "gssd".
We'll never send an upcall along that pipe, and any downcall written to
it will just return -EINVAL.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Several files refer to an old address for the Free Software Foundation
in the file header comment. Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- cpufreq regression fix from Bjørn Mork restoring the pre-3.12
behavior of the framework during system suspend/hibernation to
avoid garbage sysfs files from being left behind in case of a
suspend error.
- PNP regression fix to restore the correct states of devices after
resume from hibernation broken in 3.12. From Dmitry Torokhov.
- cpuidle fix to prevent cpuidle device unregistration from crashing
due to a NULL pointer dereference if cpuidle has been disabled
from the kernel command line. From Konrad Rzeszutek Wilk.
- intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
processors from Arne Bockholdt.
- Power capping framework fix to make the energy_uj sysfs attribute
work in accordance with the documentation. From Srinivas Pandruvada.
- epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
been compiled with CONFIG_PM_SLEEP unset (in which case that flag
should not have any effect). From Amit Pundir.
- cpufreq fix to prevent governor sysfs files from being lost over
system suspend/resume in some (arguably unusual) situations. From
Viresh Kumar.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=gHBV
-----END PGP SIGNATURE-----
Merge tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
- cpufreq regression fix from Bjørn Mork restoring the pre-3.12
behavior of the framework during system suspend/hibernation to avoid
garbage sysfs files from being left behind in case of a suspend error
- PNP regression fix to restore the correct states of devices after
resume from hibernation broken in 3.12. From Dmitry Torokhov.
- cpuidle fix to prevent cpuidle device unregistration from crashing
due to a NULL pointer dereference if cpuidle has been disabled from
the kernel command line. From Konrad Rzeszutek Wilk.
- intel_idle fix for the C6 state definition on Intel Avoton/Rangeley
processors from Arne Bockholdt.
- Power capping framework fix to make the energy_uj sysfs attribute
work in accordance with the documentation. From Srinivas Pandruvada.
- epoll fix to make it ignore the EPOLLWAKEUP flag if the kernel has
been compiled with CONFIG_PM_SLEEP unset (in which case that flag
should not have any effect). From Amit Pundir.
- cpufreq fix to prevent governor sysfs files from being lost over
system suspend/resume in some (arguably unusual) situations. From
Viresh Kumar.
* tag 'pm-3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PowerCap: Fix mode for energy counter
PNP: fix restoring devices after hibernation
cpuidle: Check for dev before deregistering it.
epoll: drop EPOLLWAKEUP if PM_SLEEP is disabled
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
intel_idle: Fixed C6 state on Avoton/Rangeley processors
The code to detect fragments in checksum_setup() was missing for IPv4 and
too eager for IPv6. (It transpires that Windows seems to send IPv6 packets
with a fragment header even if they are not a fragment - i.e. offset is zero,
and M bit is not set).
This patch also incorporates a fix to callers of maybe_pull_tail() where
skb->network_header was being erroneously added to the length argument.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: Zoltan Kiss <zoltan.kiss@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
cc: David Miller <davem@davemloft.net>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-cpuidle:
cpuidle: Check for dev before deregistering it.
intel_idle: Fixed C6 state on Avoton/Rangeley processors
* pm-cpufreq:
cpufreq: fix garbage kobjects on errors during suspend/resume
cpufreq: suspend governors on system suspend/hibernate
- Stable fix for a NFSv4.1 delegation and state recovery deadlock
- Stable fix for a loop on irrecoverable errors when returning delegations
- Fix a 3-way deadlock between layoutreturn, open, and state recovery
- Update the MAINTAINERS file with contact information for Trond Myklebust
- Close needs to handle NFS4ERR_ADMIN_REVOKED
- Enabling v4.2 should not recompile nfsd and lockd
- Fix a couple of compile warnings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSoLTpAAoJEGcL54qWCgDy2dgQAIKkKAXccg3OG2b1SxJmiaja
PcrovNmgg3HvYQ7clUMqtrMByiXEpSybl6tAeXYUWE3sS1DISSBVEwO3MoOiASiM
951Ssx+CoyhsHYo5aH83sUIiWFl/YsRhpKmSr2cdQd13DQTFbPq896k64Inf6L2/
9fngoqOD7FunQHn8AiVPoDOQzObB0OuKhYCwuwLt47oPiwgmm12JQNCDxU1i4sxb
lkGUBLkPMs6D5IyI8XHaMyX3+8MvmPiIsjIKaNJRdhkuX/k7ollucTJXyvyEQKK0
PhBIWyUULmKcAXYwCfHf9UoyGZFvmj47YggyKcBd26OZUEFekcWrULfym46F1xak
EcO6D4mlTy5i5W0RBqYCj1oGud57rixZBmhLTbeq6sSJaiqBfGEs225Q17H7rsEB
YIghHiEFNnBmVWELhHxbJHQoY6HOugmZOuc0dxopaikN/7to8gnYoVyTIVlMfe/t
UNXZoer6GOOohJGtZ7s7v4Al7EzvwnVnBCBklEAKFJ7Ca2LEmq+b58oQW3nJ1mPn
y4TnihxYXsSEbqy+Lds9rumRhJLG1oVTpwficAm7N3HdK3abzCIPEt6iOHoCmXQz
J1B4gmwOKsDqVlCSpBsnc3ZiBlSJGOn6MmVQUCNFpzv/DetWn/BxEUPE8cNm8DaI
WioD0grC0/9bR8oD1m+w
=UZ51
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix for a NFSv4.1 delegation and state recovery deadlock
- Stable fix for a loop on irrecoverable errors when returning
delegations
- Fix a 3-way deadlock between layoutreturn, open, and state recovery
- Update the MAINTAINERS file with contact information for Trond
Myklebust
- Close needs to handle NFS4ERR_ADMIN_REVOKED
- Enabling v4.2 should not recompile nfsd and lockd
- Fix a couple of compile warnings
* tag 'nfs-for-3.13-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: fix do_div() warning by instead using sector_div()
MAINTAINERS: Update contact information for Trond Myklebust
NFSv4.1: Prevent a 3-way deadlock between layoutreturn, open and state recovery
SUNRPC: do not fail gss proc NULL calls with EACCES
NFSv4: close needs to handle NFS4ERR_ADMIN_REVOKED
NFSv4: Update list of irrecoverable errors on DELEGRETURN
NFSv4 wait on recovery for async session errors
NFS: Fix a warning in nfs_setsecurity
NFS: Enabling v4.2 should not recompile nfsd and lockd
When CONFIG_DEBUG_FORCE_WEAK_PER_CPU or CONFIG_ARCH_NEEDS_WEAK_PER_CPU
is set, DEFINE_PER_CPU() explodes into cryptic series of definitions
to still allow using "static" for percpu variables while keeping all
per-cpu symbols unique in the kernel image which is required for weak
symbols. This ultimately converts the actual symbol to global whether
DEFINE_PER_CPU() is prefixed with static or not.
Unfortunately, the macro forgot to add explicit extern declartion of
the actual symbol ending up defining global symbol without preceding
declaration for static definitions which naturally don't have matching
DECLARE_PER_CPU(). The only ill effect is triggering of the following
warnings.
fs/inode.c:74:8: warning: symbol 'nr_inodes' was not declared. Should it be static?
fs/inode.c:75:8: warning: symbol 'nr_unused' was not declared. Should it be static?
Fix it by adding extern declaration in the DEFINE_PER_CPU() macro.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
In preparation of conversion to kernfs, cgroup file handling is
updated so that it can be easily mapped to kernfs. With the previous
changes, the difference between pidlist and other files are very
small. Both are served by seq_file in a pretty standard way with the
only difference being !pidlist files use single_open().
This patch adds cftype->seq_start(), ->seq_next and ->seq_stop() and
implements the matching cgroup_seqfile_start/next/stop() which either
emulates single_open() behavior or invokes cftype->seq_*() operations
if specified. This allows using single seq_operations for both
pidlist and other files and makes cgroup_pidlist_operations and
cgorup_pidlist_open() no longer necessary. As cgroup_pidlist_open()
was the only user of cftype->open(), the method is dropped together.
This brings cftype file interface very close to kernfs interface and
mapping shouldn't be too difficult. Once converted to kernfs, most of
the plumbing code including cgroup_seqfile_*() will be removed as
kernfs provides those facilities.
This patch does not introduce any behavior changes.
v2: Refreshed on top of the updated "cgroup: introduce struct
cgroup_pidlist_open_file".
v3: Refreshed on top of the updated "cgroup: attach cgroup_open_file
to all cgroup files".
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
In preparation of conversion to kernfs, cgroup file handling is
updated so that it can be easily mapped to kernfs. This patch
replaces cftype->read_seq_string() with cftype->seq_show() which is
not limited to single_open() operation and will map directcly to
kernfs seq_file interface.
The conversions are mechanical. As ->seq_show() doesn't have @css and
@cft, the functions which make use of them are converted to use
seq_css() and seq_cft() respectively. In several occassions, e.f. if
it has seq_string in its name, the function name is updated to fit the
new method better.
This patch does not introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Aristeu Rozanski <arozansk@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
In preparation of conversion to kernfs, cgroup file handling is
updated so that it can be easily mapped to kernfs. This patch
attaches cgroup_open_file, which used to be attached to pidlist files,
to all cgroup files, introduces seq_css/cft() accessors to determine
the cgroup_subsys_state and cftype associated with a given cgroup
seq_file, exports them as public interface.
This doesn't cause any behavior changes but unifies cgroup file
handling across different file types and will help converting them to
kernfs seq_show() interface.
v2: Li pointed out that the original patch was using
single_open_size() incorrectly assuming that the size param is
private data size. Fix it by allocating @of separately and
passing it to single_open() and explicitly freeing it in the
release path. This isn't the prettiest but this path is gonna be
restructured by the following patches pretty soon.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
In preparation of conversion to kernfs, cgroup file handling is being
consolidated so that it can be easily mapped to the seq_file based
interface of kernfs.
After recent updates, ->read() and ->read_map() don't have any user
left and ->write() never had any user. Remove them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Disabling compiler optimizations can be fragile, since a new
optimization could be added to -O0 or -Os that breaks the assumptions
the code is making.
Instead of disabling compiler optimizations, use a dummy inline assembly
(based on RELOC_HIDE) to block the problematic kinds of optimization,
while still allowing other optimizations to be applied to the code.
The dummy inline assembly is added after every OR, and has the
accumulator variable as its input and output. The compiler is forced to
assume that the dummy inline assembly could both depend on the
accumulator variable and change the accumulator variable, so it is
forced to compute the value correctly before the inline assembly, and
cannot assume anything about its value after the inline assembly.
This change should be enough to make crypto_memneq work correctly (with
data-independent timing) even if it is inlined at its call sites. That
can be done later in a followup patch.
Compile-tested on x86_64.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.eti.br>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These routines provide the device driver support for the AMD
Cryptographic Coprocessor (CCP).
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull x86 and EFI fixes from Peter Anvin:
"Half of these are EFI-related:
The by far biggest change is the change to hold off the deletion of a
sysfs entry while a backend scan is in progress. This is to avoid
calling kmemdup() while under a spinlock.
The other major change is for each entry in the EFI pstore backend to
get a unique identifier, as required by the pstore filesystem proper.
The other changes are:
A fix to the recent consolidation and optimization of using "asm goto"
with read-modify-write operation, which broke the bitops; specifically
in such a way that we could end up generating invalid code.
A build hack to make sure we compile with -mno-sse. icc, and most
likely future versions of gcc, can generate SSE instructions unless we
tell it not to.
A comment-only patch to a change the was due in part to an unpublished
erratum; now when the erratum is published we want to add a comment
explaining why"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic, doc: Justification for disabling IO APIC before Local APIC
x86, bitops: Correct the assembly constraints to testing bitops
x86-64, build: Always pass in -mno-sse
efi-pstore: Make efi-pstore return a unique id
x86/efi: Fix earlyprintk off-by-one bug
efivars, efi-pstore: Hold off deletion of sysfs entry until the scan is completed
This is the first step to move AT91 to the CCF.
- core CCF and drivers for most of the clocks
- use of CCF for sama5d3 (100% DT-based)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSnLhVAAoJEAf03oE53VmQugkH/11ZuSaLsjn31/WvE4WwKdgc
RCIx7r8BCmPLNwDFOgc7tsheH7Jb6I7BNv4MnX8NIPrcAGy6yCEaD8TqhwKGTs9s
2YGoKB48fpwm1udDc6Hfq3/yqkPvM7AnzE1ei1rJNmLt2582tlX1FI+klQG5EoUK
23Pf4yjxtxt31s6xjuvRjEVjEat4PWnuVLs0nZWK6mizApXjA1JPIsKS6NL7q+eG
aBMWDGw0DW4M8VEHAZygxF16PRXnumuB7NAIxKp8SJW5/acSeQntJTNXisMQBem7
DxWfvK7WAFEBGUcRN33a9RpKaHg0Gur1If2sw6CkZ83RnRV9CLqURty1mO4WCUo=
=B+yP
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup' of git://github.com/at91linux/linux-at91 into next/cleanup
From Nicolas Ferre:
AT91: Move to Common Clock Framework and sama5d3 implementation
This is the first step to move AT91 to the CCF.
- core CCF and drivers for most of the clocks
- use of CCF for sama5d3 (100% DT-based)
* tag 'at91-cleanup' of git://github.com/at91linux/linux-at91: (22 commits)
ARM: at91/dt: remove old clk material
ARM: at91: move sama5d3 SoC to common clk
ARM: at91/dt: define sama5d3xek's main clk frequency
ARM: at91/dt: define sama5d3 clocks
ARM: at91: prepare common clk transition for sama5d3 SoC
ARM: at91: prepare sama5 dt boards transition to common clk
ARM: at91: add new compatible strings for pmc driver
ARM: at91: move pit timer to common clk framework
dt: binding: add at91 clks dt bindings documentation
clk: at91: add PMC smd clock
clk: at91: add PMC usb clock
clk: at91: add PMC utmi clock
clk: at91: add PMC programmable clocks
clk: at91: add PMC peripheral clocks
clk: at91: add PMC system clocks
clk: at91: add PMC master clock
clk: at91: add PMC pll clocks
clk: at91: add PMC main clock
clk: at91: add PMC macro file for dt definitions
clk: at91: add PMC base support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix compile warnings.
- Fix overly talkative diagnostic messages from usual use
cases wrt GPIO descriptors.
- Add a documentation 00-INDEX
- Use platform GPIOs as fallback when ACPI or device tree is
used as the primary means to get GPIO lines.
- A bug fix for the MPC8572/MPC8536 fixing erroneous input data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=PJQJ
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here are a few more GPIO patches, we're a bit noisy for being the GPIO
subsystem, mostly due to the new descriptor API, but all is getting
into shape.
- Fix compile warnings
- Fix overly talkative diagnostic messages from usual use cases wrt
GPIO descriptors
- Add a documentation 00-INDEX
- Use platform GPIOs as fallback when ACPI or device tree is used as
the primary means to get GPIO lines
- A bug fix for the MPC8572/MPC8536 fixing erroneous input data"
* tag 'gpio-v3.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: change a warning to debug message when failing to get gpio
powerpc/gpio: Fix the wrong GPIO input data on MPC8572/MPC8536
gpiolib: use platform GPIO mappings as fallback
Documentation: gpiolib: add 00-INDEX file
gpiolib: fix lookup of platform-mapped GPIOs
gpiolib: add missing declarations
clk_unregister() is currently not implemented and it is required when
a clock provider module needs to be unloaded.
Normally the clock supplier module is prevented to be unloaded by
taking reference on the module in clk_get().
For cases when the clock supplier module deinitializes despite the
consumers of its clocks holding a reference on the module, e.g. when
the driver is unbound through "unbind" sysfs attribute, there are
empty clock ops added. These ops are assigned temporarily to struct
clk and used until all consumers release the clock, to avoid invoking
callbacks from the module which just got removed.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds common __clk_get(), __clk_put() clkdev helpers that
replace their platform specific counterparts when the common clock
API is used.
The owner module pointer field is added to struct clk so a reference
to the clock supplier module can be taken by the clock consumers.
The owner module is assigned while the clock is being registered,
in functions _clk_register() and __clk_register().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
This switches the two members of struct gpio_chip that were
defined as unsigned foo:1 to bool, because that is indeed what
they are. Switch all users in the gpio and pinctrl subsystems
to assign these values with true/false instead of 0/1. The
users outside these subsystems will survive since true/false
is 1/0, atleast we set some kind of more strict typing example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch introduces an API to register cpufreq cooling device
based on device tree node.
The registration via device tree node differs from normal
registration due to the fact that it is needed to fill
the device_node structure in order to be able to match
the cooling devices with trip points.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch adds a new API to allow registering cooling devices
in the thermal framework derived from device tree nodes.
This API links the cooling device with the device tree node
so that binding with thermal zones is possible, given
that thermal zones are pointing to cooling device
device tree nodes.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
This patch introduces a device tree bindings for
describing the hardware thermal behavior and limits.
Also a parser to read and interpret the data and feed
it in the thermal framework is presented.
This patch introduces a thermal data parser for device
tree. The parsed data is used to build thermal zones
and thermal binding parameters. The output data
can then be used to deploy thermal policies.
This patch adds also documentation regarding this
API and how to define tree nodes to use
this infrastructure.
Note that, in order to be able to have control
on the sensor registration on the DT thermal zone,
it was required to allow changing the thermal zone
.get_temp callback. For this reason, this patch
also removes the 'const' modifier from the .ops
field of thermal zone devices.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
Pull dynticks updates from Frederic Weisbecker:
* Fix a bug where posix cpu timers requeued due to interval got ignored on full
dynticks CPUs (not a regression though as it only impacts full dynticks and the
bug is there since we merged full dynticks).
* Optimizations and cleanups on the use of per CPU APIs to improve code readability,
performance and debuggability in the nohz subsystem;
* Optimize posix cpu timer by sparing stub workqueue queue with full dynticks off case
* Rename some functions to extend with *_this_cpu() suffix for clarity
* Refine the naming of some context tracking subsystem state accessors
* Trivial spelling fix by Paul Gortmaker
Signed-off-by: Ingo Molnar <mingo@kernel.org>
- Fix up tc3589x bindings so this chip works again.
- Remove SSP platform devices, as we now boot from device tree
exclusively.
- Delete surplus AB8500/DB8500 platform data, not obtained from
the device tree.
- Add DMA config for the MSP devices.
- A series of 21 patches moving pin control config for the
on-chip Nomadik pin controller from the board file
to the device tree, step by step.
- Two patches to the STE DMA40 driver regarding the high-prio
DMA channel so this can be moved to the device tree. Both have
Vinod's ACK.
- Decommission of the non-device tree boot path for the timer
initialization code.
- Deletion of the non-devicetree probe path from the MTU timer
driver, as all platforms using it are now using device tree.
This has Daniel Lezcano's ACK.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSlQIFAAoJEEEQszewGV1zaaoP/iUClda7fps7dhBZMHOaDr48
DAe9yBaUoGBgyjOd0QUUP4/P5PxsXQVCM13gdaITt+R4eg8XYxG3jLNxopMfGKYV
bifbXqEd4wf0t8yUYCzhdfAeWchzSph3W2C7I2hW09b9nhJ+RWgXdzcO061E9Tbj
BbZ4aS7IR3HfXzQ/zdMBtlbNXkWtn++HXCjC5Z0t0FKqSL7X8LKZrr3GEHZ6vfnB
sI5/bTK3AfXt7h2wsu4z/IZK89Ttt9AATNhxajW2Pptkuggc+/KfRRDyYeZFBT70
9KIRsF3NXSsOhOYcRNbWjNU2S8OtC7UyKMB5+y07cYU53ehaiEH8tUMait1cphlc
kFJAqKXY87I85E6WTEgv1s4Q8H3rQzVc/IjT3LODFbuM3MeTrsrnbKDeFCOqqpJC
4Ggq6VBXhn7G2srcM5KBYZcZhmq86qhmo0/vUOqaYcdmgdD7KJyewLNafYf5W+DX
JxVlnzpdWsAhihUV3oBeJybM0YGvE1wa855ZqbsAZ8nrLTBoTD+zi30mIhXrQwQp
v54ywGa0JtjpTLY6EZG2Rptq4qOUVUbkuNSv+3BYgVTqxCcCqXOu+tuzGk2O1jTh
8/2biKCCrdbSWCmbMZDi7jlkO5ywqcn2Brav5KyZ+bCwITRybfoxeOv6f8DCT741
bwx00XNaYVO/H+Vptd+h
=w9pg
-----END PGP SIGNATURE-----
Merge tag 'ux500-devicetree-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
From Linus Walleij:
Ux500 device tree patches for v3.14, take one:
- Fix up tc3589x bindings so this chip works again.
- Remove SSP platform devices, as we now boot from device tree
exclusively.
- Delete surplus AB8500/DB8500 platform data, not obtained from
the device tree.
- Add DMA config for the MSP devices.
- A series of 21 patches moving pin control config for the
on-chip Nomadik pin controller from the board file
to the device tree, step by step.
- Two patches to the STE DMA40 driver regarding the high-prio
DMA channel so this can be moved to the device tree. Both have
Vinod's ACK.
- Decommission of the non-device tree boot path for the timer
initialization code.
- Deletion of the non-devicetree probe path from the MTU timer
driver, as all platforms using it are now using device tree.
This has Daniel Lezcano's ACK.
* tag 'ux500-devicetree-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson: (39 commits)
ARM: ux500: decomission custom SMP TWD timer init
clksrc: delete nomadik MTU non-DT boot path
ARM: ux500: decomission the non-DT MTU init sequence
dma: ste_dma40: Parse flags property for new 'high priority channel' request
dma: ste_dma40: Expand DT binding to accept 'high-priority channel' flag
ARM: ux500: Remove checking for DT during timer init
ARM: ux500: Clean-up legacy extern prototype
ARM: ux500: Remove unused call to register AMBA devices
ARM: ux500: Clean-up non-DT IRQ initialisation
pinctrl: nomadik: decomission non-DT boot path
pinctrl: nomadik: move platform data handling into driver
ARM: ux500: get rid of unused header
ARM: ux500: delete Nomadik pinctrl AUXDATA
ARM: ux500: delete remnant pin config macros
ARM: ux500: move snowball pin configs to device tree
ARM: ux500: move snowball LED pin control to device tree
ARM: ux500: convert Snowball SPI pin reference
ARM: ux500: move snowball ethernet config to device tree
ARM: ux500: move HREFv60plus pin configs to device tree
ARM: ux500: move final HREFv60 LCD pins to device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
2 fixes here.
* The gp2ap020a00f is a simple missing kconfig dependency.
* The hid sensors hub fix is a work around for an issue introduced by hardware
changes due to a certain large software vendor having an 'interesting'
interpretation of the specification and hence indexing some arrays from 1
rather than 0. The fix takes advantage of the logical min and max reading
facilities introduced by the precursor patch to figure out whether we have
a 0 indexed or 1 indexed device and to adjust appropriately. It also
drops a previous kconfig option that allowed this issue to be worked around
at build time.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BgVg
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second round of IIO fixes for the 3.13 cycle.
2 fixes here.
* The gp2ap020a00f is a simple missing kconfig dependency.
* The hid sensors hub fix is a work around for an issue introduced by hardware
changes due to a certain large software vendor having an 'interesting'
interpretation of the specification and hence indexing some arrays from 1
rather than 0. The fix takes advantage of the logical min and max reading
facilities introduced by the precursor patch to figure out whether we have
a 0 indexed or 1 indexed device and to adjust appropriately. It also
drops a previous kconfig option that allowed this issue to be worked around
at build time.
Added usage id processing for Inclinometer 3D. This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There are already humidity sensors in the hwmon subsystem,
so we use their unit (milli percent) here as well.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a new data_available() callback to the iio_buffer_access_funcs
struct. The callback is used to indicate whether data is available in the buffer
for reading. It is meant to replace the stufftoread flag from the iio_buffer
struct. The reasoning for this is that the buffer implementation usually can
determine whether data is available rather easily based on its state, on the
other hand it can be rather tricky to update the stufftoread flag in a race free
way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Traditionally the "get" functions increment the reference count of the
object that is returned, which does not happen with vme_slot_get. The
function vme_slot_get returns the physical VME slot associated with a
particular struct vme_dev. Rename vme_slot_num to avoid any confusion.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The match function for vme_user is completely wrong. It will blindly bind
against the first VME slot on each bus (at this point that would be just the
first bus as the driver can only handle one bus).
The original intention (before some major subsystem changes) was that the
driver bind against the slot to which the bridge was attached in the VME
system and to the bus(es) provided via the "bus" module parameter.
To do this cleanly (i.e. without poking arround in the subsystems internal
stuctures) a functionality has been added to provide access to the bus
enumeration.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add declaration of 'struct of_phandle_args' to avoid the following
warning:
In file included from arch/arm/mach-tegra/board-paz00.c:21:0:
include/linux/gpio/driver.h:102:17: warning: 'struct of_phandle_args' declared inside parameter list
include/linux/gpio/driver.h:102:17: warning: its scope is only this definition or declaration, which is probably not what you want
Also proactively add other definitions/includes that could be missing
in other contexts.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PIN_CONFIG_OUTPUT parameter is really tricky to understand
and needs an explicit pointer to the documentation.
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When multiple wireless USB devices are connected and one of the devices
disconnects, the host will distribute a new group key to the remaining
devicese using wusbhc_gtk_rekey. wusbhc_gtk_rekey takes the
wusbhc->mutex and holds it while it submits a URB to set the new key.
This causes a deadlock in wa_urb_enqueue when it calls a device lookup
helper function that takes the same lock.
This patch changes wusbhc_gtk_rekey to submit a work item to set the GTK
so that the URB is submitted without holding wusbhc->mutex.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 018c5bba05.
It causes regressions for people using chips driven by the sungem
driver. Suspicion is that the skb->csum value isn't being adjusted
properly.
The change also has a bug in that if __pskb_trim() fails, we'll leave
a corruped skb->csum value in there. We would really need to revert
it to it's original value in that case.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original HID sensor hub firmwares all Named array enums were
to 0-based. But the most recent hub implemented as 1-based,
because of the implementation by one of the major OS vendor.
Using logical minimum for the field as the base of enum. So we add
logical minimum to the selector values before setting those fields.
Some sensor hub FWs already changed logical minimum from 0 to 1
to reflect this and hope every other vendor will follow.
There is no easy way to add a common HID quirk for NAry elements,
even if the standard specifies these field as NAry, the collection
used to describe selectors is still just "logical".
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Exporting logical minimum and maximum of HID fields as part of the
hid sensor attribute info. This can be used for range checking and
to calculate enumeration base for NAry fields of HID sensor hub.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Modify tg3_chip_reset() and tg3_close() to check if the PCI network
adapter device is accessible at all in order to skip poking it or
trying to handle a carrier loss in vain when that's not the case.
Introduce a special PCI helper function pci_device_is_present()
for this purpose.
Of course, this uncovers the lack of the appropriate RTNL locking
in tg3_suspend() and tg3_resume(), so add that locking in there
too.
These changes prevent tg3 from burning a CPU at 100% load level for
solid several seconds after the Thunderbolt link is disconnected from
a Matrox DS1 docking station.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB
can only occur at a boundary between underlying USB frames (512 bytes for
high speed devices).
If this isn't done the USB frames aren't formatted correctly and, for example,
the USB3 ethernet ax88179_178a card will stop sending (while still receiving)
when running a netperf tcp transmit test with (say) and 8k buffer.
This should be a candidate for stable, the ax88179_178a driver defaults to
gso and tso enabled so it passes a lot of fragmented skb to the USB stack.
Notes from Sarah:
Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2
This patch fixes a long-standing xHCI driver bug that was revealed by a
change in 3.12 in the usb-net driver. Commit
638c5115a7 "USBNET: support DMA SG" added
support to use bulk endpoint scatter-gather (urb->sg). Only the USB
ethernet drivers trigger this bug, because the mass storage driver sends
sg list entries in page-sized chunks.
This patch only fixes the issue for bulk endpoint scatter-gather. The
problem will still occur for periodic endpoints, because hosts will
interpret no-op transfers as a request to skip a service interval, which
is not what we want.
Luckily, the USB core isn't set up for scatter-gather on isochronous
endpoints, and no USB drivers use scatter-gather for interrupt
endpoints. Document this known limitation so that developers won't try
to use urb->sg for interrupt endpoints until this issue is fixed. The
more comprehensive fix would be to allow link TRBs in the middle of the
endpoint ring and revert this patch, but that fix would touch too much
code to be allowed in for stable.
This patch should be backported to kernels as old as 3.12, that contain
the commit 638c5115a7 "USBNET: support DMA
SG". Without this patch, the USB network device gets wedged, and stops
sending packets. Mark Lord confirms this patch fixes the regression:
http://marc.info/?l=linux-netdev&m=138487107625966&w=2
Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: stable@vger.kernel.org
We currently have a confusing couple of API naming with the existing
context_tracking_active() and context_tracking_is_enabled().
Lets keep the latter one, context_tracking_is_enabled(), for global
context tracking state check and use context_tracking_cpu_is_enabled()
for local state check.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Use a function with a meaningful name to check the global context
tracking state. static_key_false() is a bit confusing for reviewers.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
A few functions use remote per CPU access APIs when they
deal with local values.
Just do the right conversion to improve performance, code
readability and debug checks.
While at it, lets extend some of these function names with *_this_cpu()
suffix in order to display their purpose more clearly.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Pull irq fixes from Thomas Gleixner:
- Correction of fuzzy and fragile IRQ_RETVAL macro
- IRQ related resume fix affecting only XEN
- ARM/GIC fix for chained GIC controllers
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: Gic: fix boot for chained gics
irq: Enable all irqs unconditionally in irq_resume
genirq: Correct fuzzy and fragile IRQ_RETVAL() definition
Pull scheduler fixes from Ingo Molnar:
"Various smaller fixlets, all over the place"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/doc: Fix generation of device-drivers
sched: Expose preempt_schedule_irq()
sched: Fix a trivial typo in comments
sched: Remove unused variable in 'struct sched_domain'
sched: Avoid NULL dereference on sd_busy
sched: Check sched_domain before computing group power
MAINTAINERS: Update file patterns in the lockdep and scheduler entries
Pull perf fixes from Ingo Molnar:
"Misc kernel and tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tools lib traceevent: Fix conversion of pointer to integer of different size
perf/trace: Properly use u64 to hold event_id
perf: Remove fragile swevent hlist optimization
ftrace, perf: Avoid infinite event generation loop
tools lib traceevent: Fix use of multiple options in processing field
perf header: Fix possible memory leaks in process_group_desc()
perf header: Fix bogus group name
perf tools: Tag thread comm as overriden
Binary was written as binay, probably by mistake. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch adds new at91 pll clock implementation using common clk framework.
The pll clock layout describe the PLLX register layout.
There are four pll clock layouts:
- at91rm9200
- at91sam9g20
- at91sam9g45
- sama5d3
PLL clocks are given characteristics:
- min/max clock source rate
- ranges of valid clock output rates
- values to set in out and icpll fields for each supported output range
These characteristics are checked during rate change to avoid
over/underclocking.
These characteristics are described in atmel's SoC datasheet in
"Electrical Characteristics" paragraph.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch moves at91_pmc.h header from machine specific directory
(arch/arm/mach-at91/include/mach/at91_pmc.h) to clk include directory
(include/linux/clk/at91_pmc.h).
We need this to avoid reference to machine specific headers in clk
drivers.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
We have a problem where the big_key key storage implementation uses a
shmem backed inode to hold the key contents. Because of this detail of
implementation LSM checks are being done between processes trying to
read the keys and the tmpfs backed inode. The LSM checks are already
being handled on the key interface level and should not be enforced at
the inode level (since the inode is an implementation detail, not a
part of the security model)
This patch implements a new function shmem_kernel_file_setup() which
returns the equivalent to shmem_file_setup() only the underlying inode
has S_PRIVATE set. This means that all LSM checks for the inode in
question are skipped. It should only be used for kernel internal
operations where the inode is not exposed to userspace without proper
LSM checking. It is possible that some other users of
shmem_file_setup() should use the new interface, but this has not been
explored.
Reproducing this bug is a little bit difficult. The steps I used on
Fedora are:
(1) Turn off selinux enforcing:
setenforce 0
(2) Create a huge key
k=`dd if=/dev/zero bs=8192 count=1 | keyctl padd big_key test-key @s`
(3) Access the key in another context:
runcon system_u:system_r:httpd_t:s0-s0:c0.c1023 keyctl print $k >/dev/null
(4) Examine the audit logs:
ausearch -m AVC -i --subject httpd_t | audit2allow
If the last command's output includes a line that looks like:
allow httpd_t user_tmpfs_t:file { open read };
There was an inode check between httpd and the tmpfs filesystem. With
this patch no such denial will be seen. (NOTE! you should clear your
audit log if you have tested for this previously)
(Please return you box to enforcing)
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Hugh Dickins <hughd@google.com>
cc: linux-mm@kvack.org
If sufficient keys (or keyrings) are added into a keyring such that a node in
the associative array's tree overflows (each node has a capacity N, currently
16) and such that all N+1 keys have the same index key segment for that level
of the tree (the level'th nibble of the index key), then assoc_array_insert()
calls ops->diff_objects() to indicate at which bit position the two index keys
vary.
However, __key_link_begin() passes a NULL object to assoc_array_insert() with
the intention of supplying the correct pointer later before we commit the
change. This means that keyring_diff_objects() is given a NULL pointer as one
of its arguments which it does not expect. This results in an oops like the
attached.
With the previous patch to fix the keyring hash function, this can be forced
much more easily by creating a keyring and only adding keyrings to it. Add any
other sort of key and a different insertion path is taken - all 16+1 objects
must want to cluster in the same node slot.
This can be tested by:
r=`keyctl newring sandbox @s`
for ((i=0; i<=16; i++)); do keyctl newring ring$i $r; done
This should work fine, but oopses when the 17th keyring is added.
Since ops->diff_objects() is always called with the first pointer pointing to
the object to be inserted (ie. the NULL pointer), we can fix the problem by
changing the to-be-inserted object pointer to point to the index key passed
into assoc_array_insert() instead.
Whilst we're at it, we also switch the arguments so that they are the same as
for ->compare_object().
BUG: unable to handle kernel NULL pointer dereference at 0000000000000088
IP: [<ffffffff81191ee4>] hash_key_type_and_desc+0x18/0xb0
...
RIP: 0010:[<ffffffff81191ee4>] hash_key_type_and_desc+0x18/0xb0
...
Call Trace:
[<ffffffff81191f9d>] keyring_diff_objects+0x21/0xd2
[<ffffffff811f09ef>] assoc_array_insert+0x3b6/0x908
[<ffffffff811929a7>] __key_link_begin+0x78/0xe5
[<ffffffff81191a2e>] key_create_or_update+0x17d/0x36a
[<ffffffff81192e0a>] SyS_add_key+0x123/0x183
[<ffffffff81400ddb>] tracesys+0xdd/0xe2
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Stephen Gallagher <sgallagh@redhat.com>
This patch adds a notifier chain to the power_supply, this helps drivers
in other subsystem to listen to changes in power supply subsystem.
This would help to take some actions in those drivers on changing the
power supply properties. One such scenario is to increase/decrease system
performance based on the battery capacity/voltage. Another scenario is to
adjust the h/w peak current detection voltage/current thresholds based on
battery voltage/capacity. The notifier helps drivers to listen to changes
in power_suppy susbystem without polling the power_supply properties
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
fs/sysfs/symlink.c::sysfs_delete_link() tests @sd->s_flags for
SYSFS_FLAG_NS. Let's add kernfs_ns_enabled() so that sysfs doesn't
have to test sysfs_dirent flag directly. This makes things tidier for
kernfs proper too.
This is purely cosmetic.
v2: To avoid possible NULL deref, use noop dummy implementation which
always returns false when !CONFIG_SYSFS.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysfs_dirent includes some information which should be available to
kernfs users - the type, flags, name and parent pointer. This patch
moves sysfs_dirent definition from kernfs/kernfs-internal.h to
include/linux/kernfs.h so that kernfs users can access them.
The type part of flags is exported as enum kernfs_node_type, the flags
kernfs_node_flag, sysfs_type() and kernfs_enable_ns() are moved to
include/linux/kernfs.h and the former is updated to return the enum
type. sysfs_dirent->s_parent and ->s_name are marked explicitly as
public.
This patch doesn't introduce any functional changes.
v2: Flags exported too and kernfs_enable_ns() definition moved.
v3: While moving kernfs_enable_ns() to include/linux/kernfs.h, v1 and
v2 put the definition outside CONFIG_SYSFS replacing the dummy
implementation with the actual implementation too. Unfortunately,
this can lead to oops when !CONFIG_SYSFS because
kernfs_enable_ns() may be called on a NULL @sd and now tries to
dereference @sd instead of not doing anything. This issue was
reported by Yuanhan Liu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're in the process of separating out core sysfs functionality into
kernfs which will deal with sysfs_dirents directly. This patch
rearranges mount path so that the kernfs and sysfs parts are separate.
* As sysfs_super_info won't be visible outside kernfs proper,
kernfs_super_ns() is added to allow kernfs users to access a
super_block's namespace tag.
* Generic mount operation is separated out into kernfs_mount_ns().
sysfs_mount() now just performs sysfs-specific permission check,
acquires namespace tag, and invokes kernfs_mount_ns().
* Generic superblock release is separated out into kernfs_kill_sb()
which can be used directly as file_system_type->kill_sb(). As sysfs
needs to put the namespace tag, sysfs_kill_sb() wraps
kernfs_kill_sb() with ns tag put.
* sysfs_dir_cachep init and sysfs_inode_init() are separated out into
kernfs_init(). kernfs_init() uses only small amount of memory and
trying to handle and propagate kernfs_init() failure doesn't make
much sense. Use SLAB_PANIC for sysfs_dir_cachep and make
sysfs_inode_init() panic on failure.
After this change, kernfs_init() should be called before
sysfs_init(), fs/namespace.c::mnt_init() modified accordingly.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernfs is being updated to allow multiple sysfs_dirent hierarchies so
that it can also be used by other users. Currently, inode number is
allocated using a global ida, sysfs_ino_ida; however, inos for
different hierarchies should be handled separately.
This patch makes ino allocation per kernfs_root. sysfs_ino_ida is
replaced by kernfs_root->ino_ida and sysfs_new_dirent() is updated to
take @root and allocate ino from it. ida_simple_get/remove() are used
instead of sysfs_ino_lock and sysfs_alloc/free_ino().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There currently is single kernfs hierarchy in the whole system which
is used for sysfs. kernfs needs to support multiple hierarchies to
allow other users. This patch introduces struct kernfs_root which
serves as the root of each kernfs hierarchy and implements
kernfs_create/destroy_root().
* Each kernfs_root is associated with a root sd (sysfs_dentry). The
root is freed when the root sd is released and kernfs_destory_root()
simply invokes kernfs_remove() on the root sd. sysfs_remove_one()
is updated to handle release of the root sd. Note that ps_iattr
update in sysfs_remove_one() is trivially updated for readability.
* Root sd's are now dynamically allocated using sysfs_new_dirent().
Update sysfs_alloc_ino() so that it gives out ino from 1 so that the
root sd still gets ino 1.
* While kernfs currently only points to the root sd, it'll soon grow
fields which are specific to each hierarchy. As determining a given
sd's root will be necessary, sd->s_dir.root is added. This backlink
fits better as a separate field in sd; however, sd->s_dir is inside
union with space to spare, so use it to save space and provide
kernfs_root() accessor to determine the root sd.
* As hierarchies may be destroyed now, each mount needs to hold onto
the hierarchy it's attached to. Update sysfs_fill_super() and
sysfs_kill_sb() so that they get and put the kernfs_root
respectively.
* sysfs_root is replaced with kernfs_root which is dynamically created
by invoking kernfs_create_root() from sysfs_init().
This patch doesn't introduce any visible behavior changes.
v2: kernfs_create_root() forgot to set @sd->priv. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce kernfs interface for finding, getting and putting
sysfs_dirents.
* sysfs_find_dirent() is renamed to kernfs_find_ns() and lockdep
assertion for sysfs_mutex is added.
* sysfs_get_dirent_ns() is renamed to kernfs_find_and_get().
* Macro inline dancing around __sysfs_get/put() are removed and
kernfs_get/put() are made proper functions implemented in
fs/sysfs/dir.c.
While the conversions are mostly equivalent, there's one difference -
kernfs_get() doesn't return the input param as its return value. This
change is intentional. While passing through the input increases
writability in some areas, it is unnecessary and has been shown to
cause confusion regarding how the last ref is handled.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, sysfs_dirent active_ref lockdep annotation uses
attribute->[s]key as the lockdep key, which forces
kernfs_create_file_ns() to assume that sysfs_dirent->priv is pointing
to a struct attribute which may not be true for non-sysfs users. This
patch restructures the lockdep annotation such that
* kernfs_ops contains lockdep_key which is used by default for files
created kernfs_create_file_ns().
* kernfs_create_file_ns_key() is introduced which takes an extra @key
argument. The created file will use the specified key for
active_ref lockdep annotation. If NULL is specified, lockdep for
the file is disabled.
* sysfs_add_file_mode_ns() is updated to use
kernfs_create_file_ns_key() with the appropriate key from the
attribute or NULL if ignore_lockdep is set.
This makes the lockdep annotation properly contained in kernfs while
allowing sysfs to cleanly keep its current behavior. This patch
doesn't introduce any behavior differences.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce kernfs interface to wake up poll(2) which takes and returns
sysfs_dirents.
sysfs_notify_dirent() is renamed to kernfs_notify() and sysfs_notify()
is updated so that it doesn't directly grab sysfs_mutex but acquires
the target sysfs_dirents using sysfs_get_dirent().
sysfs_notify_dirent() is reimplemented as a dumb inline wrapper around
kernfs_notify().
This patch doesn't introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernfs_ops currently only supports single_open() behavior which is
pretty restrictive. Add optional callbacks ->seq_{start|next|stop}()
which, when implemented, are invoked for seq_file traversal. This
allows full seq_file functionality for kernfs users. This currently
doesn't have any user and doesn't change any behavior.
v2: Refreshed on top of the updated "sysfs, kernfs: prepare read path
for kernfs".
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce kernfs interface to create a file which takes and returns
sysfs_dirents.
The actual file creation part is separated out from
sysfs_add_file_mode_ns() into kernfs_create_file_ns(). The former now
only decides the kernfs_ops to use and the file's size and invokes the
latter.
This patch doesn't introduce behavior changes.
v2: Dummy implementation for !CONFIG_SYSFS updated to return -ENOSYS.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're in the process of separating out core sysfs functionality into
kernfs which will deal with sysfs_dirents directly. This patch
introduces kernfs_ops which hosts methods kernfs users implement and
updates fs/sysfs/file.c such that sysfs_kf_*() functions populate
kernfs_ops and kernfs_file_*() functions call the matching entries
from kernfs_ops.
kernfs_ops contains the following groups of methods.
* seq_show() - for kernfs files which use seq_file for reads.
* read() - for direct read implementations. Used iff seq_show() is
not implemented.
* write() - for writes.
* mmap() - for mmaps.
Notes:
* sysfs_elem_attr->ops is added so that kernfs_ops can be accessed
from sysfs_dirent. kernfs_ops() helper is added to verify locking
and access the field.
* SYSFS_FLAG_HAS_(SEQ_SHOW|MMAP) added. sd->s_attr->ops is accessible
only while holding active_ref and there are cases where we want to
take different actions depending on which ops are implemented.
These two flags cache whether the two ops are implemented for those.
* kernfs_file_*() no longer test sysfs type but chooses different
behaviors depending on which methods in kernfs_ops are implemented.
The conversions are trivial except for the open path. As
kernfs_file_open() now decides whether to allow read/write accesses
depending on the kernfs_ops implemented, the presence of methods in
kobjs and attribute_bin should be propagated to kernfs_ops.
sysfs_add_file_mode_ns() is updated so that it propagates presence /
absence of the callbacks through _empty, _ro, _wo, _rw kernfs_ops.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sysfs_open_file will be used as the primary handle for kernfs methods.
Move its definition from fs/sysfs/file.c to include/linux/kernfs.h and
mark the public and private fields.
This is pure relocation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce kernfs interface to manipulate a directory which takes and
returns sysfs_dirents.
create_dir() is renamed to kernfs_create_dir_ns() and its argumantes
and return value are updated. create_dir() usages are replaced with
kernfs_create_dir_ns() and sysfs_create_subdir() usages are replaced
with kernfs_create_dir(). Dup warnings are handled explicitly by
sysfs users of the kernfs interface.
sysfs_enable_ns() is renamed to kernfs_enable_ns().
This patch doesn't introduce any behavior changes.
v2: Dummy implementation for !CONFIG_SYSFS updated to return -ENOSYS.
v3: kernfs_enable_ns() added.
v4: Refreshed on top of "sysfs: drop kobj_ns_type handling, take #2"
so that this patch removes sysfs_enable_ns().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, tasks and cgroup.procs guarantee that the result is
sorted. This is the only reason this whole pidlist logic is necessary
instead of just iterating through sorted member tasks. We can't do
anything about the existing interface but at least ensure that such
expectation doesn't exist for the new interface so that pidlist logic
may be removed in the distant future.
This patch scrambles the sort order if sane_behavior so that the
output is usually not sorted in the new interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Now that pidlist files don't use cftype->release(), it doesn't have
any user left. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Currently, when mounting pstore file system, a read callback of
efi_pstore driver runs mutiple times as below.
- In the first read callback, scan efivar_sysfs_list from head and pass
a kmsg buffer of a entry to an upper pstore layer.
- In the second read callback, rescan efivar_sysfs_list from the entry
and pass another kmsg buffer to it.
- Repeat the scan and pass until the end of efivar_sysfs_list.
In this process, an entry is read across the multiple read function
calls. To avoid race between the read and erasion, the whole process
above is protected by a spinlock, holding in open() and releasing in
close().
At the same time, kmemdup() is called to pass the buffer to pstore
filesystem during it. And then, it causes a following lockdep warning.
To make the dynamic memory allocation runnable without taking spinlock,
holding off a deletion of sysfs entry if it happens while scanning it
via efi_pstore, and deleting it after the scan is completed.
To implement it, this patch introduces two flags, scanning and deleting,
to efivar_entry.
On the code basis, it seems that all the scanning and deleting logic is
not needed because __efivars->lock are not dropped when reading from the
EFI variable store.
But, the scanning and deleting logic is still needed because an
efi-pstore and a pstore filesystem works as follows.
In case an entry(A) is found, the pointer is saved to psi->data. And
efi_pstore_read() passes the entry(A) to a pstore filesystem by
releasing __efivars->lock.
And then, the pstore filesystem calls efi_pstore_read() again and the
same entry(A), which is saved to psi->data, is used for resuming to scan
a sysfs-list.
So, to protect the entry(A), the logic is needed.
[ 1.143710] ------------[ cut here ]------------
[ 1.144058] WARNING: CPU: 1 PID: 1 at kernel/lockdep.c:2740 lockdep_trace_alloc+0x104/0x110()
[ 1.144058] DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
[ 1.144058] Modules linked in:
[ 1.144058] CPU: 1 PID: 1 Comm: systemd Not tainted 3.11.0-rc5 #2
[ 1.144058] 0000000000000009 ffff8800797e9ae0 ffffffff816614a5 ffff8800797e9b28
[ 1.144058] ffff8800797e9b18 ffffffff8105510d 0000000000000080 0000000000000046
[ 1.144058] 00000000000000d0 00000000000003af ffffffff81ccd0c0 ffff8800797e9b78
[ 1.144058] Call Trace:
[ 1.144058] [<ffffffff816614a5>] dump_stack+0x54/0x74
[ 1.144058] [<ffffffff8105510d>] warn_slowpath_common+0x7d/0xa0
[ 1.144058] [<ffffffff8105517c>] warn_slowpath_fmt+0x4c/0x50
[ 1.144058] [<ffffffff8131290f>] ? vsscanf+0x57f/0x7b0
[ 1.144058] [<ffffffff810bbd74>] lockdep_trace_alloc+0x104/0x110
[ 1.144058] [<ffffffff81192da0>] __kmalloc_track_caller+0x50/0x280
[ 1.144058] [<ffffffff815147bb>] ? efi_pstore_read_func.part.1+0x12b/0x170
[ 1.144058] [<ffffffff8115b260>] kmemdup+0x20/0x50
[ 1.144058] [<ffffffff815147bb>] efi_pstore_read_func.part.1+0x12b/0x170
[ 1.144058] [<ffffffff81514800>] ? efi_pstore_read_func.part.1+0x170/0x170
[ 1.144058] [<ffffffff815148b4>] efi_pstore_read_func+0xb4/0xe0
[ 1.144058] [<ffffffff81512b7b>] __efivar_entry_iter+0xfb/0x120
[ 1.144058] [<ffffffff8151428f>] efi_pstore_read+0x3f/0x50
[ 1.144058] [<ffffffff8128d7ba>] pstore_get_records+0x9a/0x150
[ 1.158207] [<ffffffff812af25c>] ? selinux_d_instantiate+0x1c/0x20
[ 1.158207] [<ffffffff8128ce30>] ? parse_options+0x80/0x80
[ 1.158207] [<ffffffff8128ced5>] pstore_fill_super+0xa5/0xc0
[ 1.158207] [<ffffffff811ae7d2>] mount_single+0xa2/0xd0
[ 1.158207] [<ffffffff8128ccf8>] pstore_mount+0x18/0x20
[ 1.158207] [<ffffffff811ae8b9>] mount_fs+0x39/0x1b0
[ 1.158207] [<ffffffff81160550>] ? __alloc_percpu+0x10/0x20
[ 1.158207] [<ffffffff811c9493>] vfs_kern_mount+0x63/0xf0
[ 1.158207] [<ffffffff811cbb0e>] do_mount+0x23e/0xa20
[ 1.158207] [<ffffffff8115b51b>] ? strndup_user+0x4b/0xf0
[ 1.158207] [<ffffffff811cc373>] SyS_mount+0x83/0xc0
[ 1.158207] [<ffffffff81673cc2>] system_call_fastpath+0x16/0x1b
[ 1.158207] ---[ end trace 61981bc62de9f6f4 ]---
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Tested-by: Madper Xie <cxie@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
- A big slew of documentation for the gpiod transition that
happened in the merge window, no semantic effect, but we should
provide proper documentation with the new API.
- Fix flags related to the new API.
- Fix to the find_chip_by_name() lookup function related to the
new API.
- Fix of_find_gpio() when not using device tree.
- Bug fix for the TB10x direction setting.
- Error path fixes from Dan Carpenter.
- Nasty IRQdomain bug relating to taking an unitialized spinlock.
- Minor fixes here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSl0gWAAoJEEEQszewGV1zSSAQAJVkZCQPMpj+NYOFs8wxubKl
t0cwISUN8VNrUOkUZbNZNev80FYbBsYGtedLiKSNKPuO/Vu0vBWPlx474XNmk0W+
OEoV9bjTFOvLYjh+JDEm5BSjHhVoHbo5dAE6/mk2GCfAxuky6XJ/U1IelV+pBVsK
+AG5ldGomVj64nd7SVnxHT6pu3IR0QspwIY0skgLzX/gmCZFse3jhdmkfuHL7TTg
94H5/FOLP9zFYhwIhu7jb+ryhvixnnhJ4vbNN16lT2ZrOVy/q1a9YYDY4CNp5Qpz
DdTHVJ2GS6z2WIwWwoz5zbjjAid0fL7I8yZ3YmsB8pCxUmRleuy5ciKqUtzyo075
A549HUxMzYuxYzCmGMI8YomMjfdpmtjGnxPd06gKyGUQmEAseAnB1UeGlK8MUMDR
pXaPTdTi+r7qECKWIk/upkTbJjvp7sW2pKrPiK1CQupgSRDAEGjqYHT4hUglJzoC
RVidfh1fb0BCG07F98LCmLTHubAzVmDVM4RjJuMb9KuCEOWEVtKjF7KII/dEtcPI
oNZBwoez4m6glcCAy194ZNn6xON19QhVK4qBB9pdl/h/cIw8JJ+yPagofzLgr25R
HsH0vSWx6lMVAYiFCRn2WKCsVeUIeZZFO6cswywlH6by8glUZOlzLiMeoO4MsoIu
UasaUADY+GKYQEbHi/GA
=GmyD
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Here us a bunch of patches for the v3.13 series. Most important stuff
is related to fixes and documentation for the new GPIO descriptor API.
If the diffstat is scary you'll notice most of it is to
Documentation/*:
- A big slew of documentation for the gpiod transition that happened
in the merge window, no semantic effect, but we should provide
proper documentation with the new API.
- Fix flags related to the new API.
- Fix to the find_chip_by_name() lookup function related to the new
API.
- Fix of_find_gpio() when not using device tree.
- Bug fix for the TB10x direction setting.
- Error path fixes from Dan Carpenter.
- Nasty IRQdomain bug relating to taking an unitialized spinlock.
- Minor fixes here and there"
* tag 'gpio-v3.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: bcm281xx: Fix return value of bcm_kona_gpio_get()
gpio: pl061: move irqdomain initialization
gpio: ucb1400: Add MODULE_ALIAS
gpiolib: fix of_find_gpio() when OF not defined
gpio: fix memory leak in error path
gpio: rcar: NULL dereference on error in probe()
gpio: msm: make msm_gpio.summary_irq signed for error handling
gpio: mvebu: make mvchip->irqbase signed for error handling
gpiolib: use dedicated flags for GPIO properties
gpiolib: fix find_chip_by_name()
Documentation: gpiolib: document new interface
gpio: tb10x: Set output value before setting direction to output
This patch adds cpufreq suspend/resume calls to dpm_{suspend|resume}_noirq()
for handling suspend/resume of cpufreq governors.
Lan Tianyu (Intel) & Jinhyuk Choi (Broadcom) found anr issue where
tunables configuration for clusters/sockets with non-boot CPUs was
getting lost after suspend/resume, as we were notifying governors
with CPUFREQ_GOV_POLICY_EXIT on removal of the last cpu for that
policy and so deallocating memory for tunables. This is fixed by
this patch as we don't allow any operation on governors after
device suspend and before device resume now.
Reported-and-tested-by: Lan Tianyu <tianyu.lan@intel.com>
Reported-by: Jinhyuk Choi <jinchoi@broadcom.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog, minor cleanups]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here are a number of staging, and IIO driver, fixes for 3.13-rc2 that
resolve issues that have been reported for 3.13-rc1. All of these have
been in linux-next for a bit this week.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlKWdiEACgkQMUfUDdst+ynbywCfaED1OKlzXXx/VbCd5WRlYd2a
2IEAoJ4c6LmgW9Vn6z0M/pRblvmPyYj1
=Tq5a
-----END PGP SIGNATURE-----
Merge tag 'staging-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are a number of staging, and IIO driver, fixes for 3.13-rc2 that
resolve issues that have been reported for 3.13-rc1. All of these
have been in linux-next for a bit this week"
* tag 'staging-3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (25 commits)
Staging: tidspbridge: disable driver
staging: zsmalloc: Ensure handle is never 0 on success
staging/lustre/ptlrpc: fix ptlrpc_stop_pinger logic
staging: r8188eu: Fix AP mode
Staging: btmtk_usb: Add hdev parameter to hdev->send driver callback
Staging: go7007: fix up some remaining go->dev issues
staging: imx-drm: Fix modular build of DRM_IMX_IPUV3
staging: ft1000: fix use of potentially uninitialized variable
Revert "staging:media: Use dev_dbg() instead of pr_debug()"
Staging: zram: Fix memory leak by refcount mismatch
staging: vt6656: [BUG] Fix for TX USB resets from vendors driver.
staging: nvec: potential NULL dereference on error path
Staging: vt6655-6: potential NULL dereference in hostap_disable_hostapd()
staging: comedi: s626: fix value written by s626_set_dac()
Staging: comedi: pcl730: fix some bitwise vs logical AND bugs
staging: comedi: fix potentially uninitialised variable
iio:accel:kxsd9 fix missing mutex unlock
iio: adc: ti_am335x_adc: avoid double free of buffer.
staging:iio: Fix hmc5843 Kconfig dependencies
iio: Fix tcs3472 Kconfig dependencies
...
Introduce kernfs setattr interface - kernfs_setattr().
sysfs_sd_setattr() is renamed to __kernfs_setattr() and
kernfs_setattr() is a simple wrapper around it with sysfs_mutex
locking. sysfs_chmod_file() is updated to get an explicit ref on
kobj->sd and then invoke kernfs_setattr() so that it doesn't have to
use internal interface.
This patch doesn't introduce any behavior differences.
v2: Dummy implementation for !CONFIG_SYSFS updated to return -ENOSYS.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce kernfs rename interface, krenfs_rename[_ns]().
This is just rename of sysfs_rename(). No functional changes.
Function comment is added to kernfs_rename_ns() and @new_parent_sd is
renamed to @new_parent for consistency with other kernfs interfaces.
v2: Dummy implementation for !CONFIG_SYSFS updated to return -ENOSYS.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Separate out kernfs symlink interface - kernfs_create_link() - which
takes and returns sysfs_dirents, from sysfs_do_create_link_sd().
sysfs_do_create_link_sd() now just determines the parent and target
sysfs_dirents and invokes the new interface and handles dup warning.
This patch doesn't introduce behavior changes.
v2: Dummy implementation for !CONFIG_SYSFS updated to return -ENOSYS.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce kernfs removal interfaces - kernfs_remove() and
kernfs_remove_by_name[_ns]().
These are just renames of sysfs_remove() and sysfs_hash_and_remove().
No functional changes.
v2: Dummy kernfs_remove_by_name_ns() for !CONFIG_SYSFS updated to
return -ENOSYS instead of 0.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Core sysfs implementation will be separated into kernfs so that it can
be used by other non-kobject users.
This patch creates fs/kernfs/ directory and makes boilerplate changes.
kernfs interface will be directly based on sysfs_dirent and its
forward declaration is moved to include/linux/kernfs.h which is
included from include/linux/sysfs.h. sysfs core implementation will
be gradually separated out and moved to kernfs.
This patch doesn't introduce any functional changes.
v2: mount.c added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-fsdevel@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The way namespace tags are implemented in sysfs is more complicated
than necessary. As each tag is a pointer value and required to be
non-NULL under a namespace enabled parent, there's no need to record
separately what type each tag is. If multiple namespace types are
needed, which currently aren't, we can simply compare the tag to a set
of allowed tags in the superblock assuming that the tags, being
pointers, won't have the same value across multiple types.
This patch rips out kobj_ns_type handling from sysfs. sysfs now has
an enable switch to turn on namespace under a node. If enabled, all
children are required to have non-NULL namespace tags and filtered
against the super_block's tag.
kobject namespace determination is now performed in
lib/kobject.c::create_dir() making sysfs_read_ns_type() unnecessary.
The sanity checks are also moved. create_dir() is restructured to
ease such addition. This removes most kobject namespace knowledge
from sysfs proper which will enable proper separation and layering of
sysfs.
This is the second try. The first one was cb26a31157 ("sysfs: drop
kobj_ns_type handling") which tried to automatically enable namespace
if there are children with non-NULL namespace tags; however, it was
broken for symlinks as they should inherit the target's tag iff
namespace is enabled in the parent. This led to namespace filtering
enabled incorrectly for wireless net class devices through phy80211
symlinks and thus network configuration failure. a1212d278c
("Revert "sysfs: drop kobj_ns_type handling"") reverted the commit.
This shouldn't introduce any behavior changes, for real.
v2: Dummy implementation of sysfs_enable_ns() for !CONFIG_SYSFS was
missing and caused build failure. Reported by kbuild test robot.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
task_is_dead() has no users since commit 43e13cc107
("cred: remove task_is_dead() from __task_cred() validation"), and
nobody except exit.c should rely on ->exit_state (we still have
the users which should be changed).
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20131113143614.GA10547@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds a new field to the struct perf_event.
It is intended to be used to chain events which are
active (enabled). It helps in the hardware layer
for PMUs which do not have actual counter restrictions, i.e.,
free running read-only counters. Active events are chained
as opposed to being tracked via the counter they use.
To save space we use a union with hlist_entry as both
are mutually exclusive (suggested by Jiri Olsa).
Signed-off-by: Stephane Eranian <eranian@google.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: acme@redhat.com
Cc: jolsa@redhat.com
Cc: zheng.z.yan@intel.com
Cc: bp@alien8.de
Cc: maria.n.dimakopoulou@gmail.com
Link: http://lkml.kernel.org/r/1384275531-10892-2-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Removing UIDGID_STRICT_TYPE_CHECKS simplifies the code and always
generates a compile error if the uids and kuids or gids and kgids are
mixed by accident. Now that the appropriate conversions have been
placed throughout the kernel there is no longer a need for a mode where
we don't detect them as compile errors.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Both platforms using the MTU (Nomadik and Ux500) have now been
converted to use device tree exclusively, thus let us delete
this platform data header and make this driver a fully
self-contained DT-only driver.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Lee Jones <lee.jones@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This decomissions the platform data header (which is no longer
in use after the systems using this driver were switched to
a pure device-tree config path) and merges the result into
the driver file or local driver header.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on OMAP,
finding new breakage of things that don't work quite right yet without
the traditional board files. I expect a bit more of this to come in this
release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec work and
to stop the MCPM core to produce a warning (the warning was new to 3.13-rc1).
- A handful of minor fixes for various platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zdhe
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Mostly bugfixes and a few small code removals. Worth pointing out is:
- A handful of more fixes to get DT enablement working properly on
OMAP, finding new breakage of things that don't work quite right
yet without the traditional board files. I expect a bit more of
this to come in this release as people test on their hardware.
- Implementation of power_down_finish() on vexpress, to make kexec
work and to stop the MCPM core to produce a warning (the warning
was new to 3.13-rc1).
- A handful of minor fixes for various platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: bcm2835: add missing #xxx-cells to I2C nodes
ARM: dts: Add max77686 RTC interrupt to cros5250-common
ARM: vexpress/TC2: Implement MCPM power_down_finish()
ARM: tegra: Provide dummy powergate implementation
ARM: omap: fix warning with LPAE build
ARM: OMAP2+: Remove legacy omap4_twl6030_hsmmc_init
ARM: OMAP2+: Remove legacy mux code for display.c
ARM: OMAP2+: Fix undefined reference to set_cntfreq
gpio: twl4030: Fix passing of pdata in the device tree case
gpio: twl4030: Fix regression for twl gpio output
ARM: OMAP2+: More randconfig fixes for reconfigure_io_chain
ARM: dts: imx6qdl: disable spdif "rxtx5" clock option
ARM: dts: Fix omap2 specific dtsi files by adding the missing entries
ARM: OMAP2+: Fix GPMC and simplify bootloader timings for 8250 and smc91x
i2c: omap: Fix missing device tree flags for omap2
Other USB drivers may want to use OTG final state machine
implementation, so make this header available for them.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dsps platform needs to save save some registers at suspend time and
restore them after resume. This patch adds a struct for these registers,
and also lets the musb core know that the core registers need to be
saved as well.
We also have to explicitly de-assert the port reset upon resume on this
platform, but musb_port_reset() should not be called from glue layers.
Hence, introduce a flag in struct musb_hdrc_config for this.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
groundwork for kexec support on EFI - Borislav Petkov
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=w6ff
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/efi
Pull EFI virtual mapping changes from Matt Fleming:
* New static EFI runtime services virtual mapping layout which is
groundwork for kexec support on EFI. (Borislav Petkov)
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The panic_timeout value can be set via the command line option
'panic=x', or via /proc/sys/kernel/panic, however that is not
sufficient when the panic occurs before we are able to set up
these values. Thus, add a CONFIG_PANIC_TIMEOUT so that we can
set the desired value from the .config.
The default panic_timeout value continues to be 0 - wait
forever. Also adds set_arch_panic_timeout(new_timeout,
arch_default_timeout), which is intended to be used by arches in
arch_setup(). The idea being that the new_timeout is only set if
the user hasn't changed from the arch_default_timeout.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: benh@kernel.crashing.org
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: mpe@ellerman.id.au
Cc: felipe.contreras@gmail.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1a1674daec27c534df409697025ac568ebcee91e.1385418410.git.jbaron@akamai.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Zorro definitions and device IDs are used by bootstraps, hence they
should be exported through UAPI.
Unfortunately zorro.h was never marked for export when headers_install
was introduced, so it was forgotten during the big UAPI disintegration.
In addition, the removal of zorro_ids.h had been sneaked into commit
7e7a43c32a ("PCI: don't export device IDs to
userspace") before, so it was also forgotten.
Split off and export the Zorro definitions used by bootstraps.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Currently the array of Zorro devices is allocated statically, wasting
up to 4.5 KiB when running an Amiga or multi-platform kernel on a machine
with no or a handful of Zorro expansion cards. Convert it to conditional
dynamic memory allocation to fix this.
amiga_parse_bootinfo() still needs to store some information about the
detected Zorro devices, at a time even the bootmem allocator is not yet
available. This is now handled using a much smaller array (typically less
than 0.5 KiB), which is __initdata and thus freed later.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This mostly consists of patches that didn't quite make the last cycle. Lots
of interesting things under review currently.
Core:
- Add devm_iio_device_register/unregister. I took some convincing on whether
there would be many devices that really were simple enough to need no
explicit actions on removal. Turns out there are some.
- Move some stray docs to above the relevant implemenation.
- Drop a redundant repeated check on the fact the trigger has actually changed
when there is a userspace attempt change it.
Drivers:
New drivers
- Freescale MPL3115A2 Pressure / temperature sensor
New functionality
- hid_sensors: add sensitivity support.
DT bindings
- tsl2563
- hmc5843
Cleanups
- Drop unused scan_type from viperboard adc driver.
- devm_iio_device_register used in viperboard, ad5421, ad5755, adis16130,
adxrs450, vcnl4000, adis16220, ad7816, lpc32xx, adt7316, adis16060, isl29018
and ad2s1200. Note that this was proposed in a number of other drivers
and this revealed a number of missorderings in remove functions. Also for
now I have blocked this on any device that any hardware suspend suport on
the basis that we probably want to power down devices if they have no driver
support loaded.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=KZou
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new features, drivers and cleanups for IIO in the 3.14 cycle.
This mostly consists of patches that didn't quite make the last cycle. Lots
of interesting things under review currently.
Core:
- Add devm_iio_device_register/unregister. I took some convincing on whether
there would be many devices that really were simple enough to need no
explicit actions on removal. Turns out there are some.
- Move some stray docs to above the relevant implemenation.
- Drop a redundant repeated check on the fact the trigger has actually changed
when there is a userspace attempt change it.
Drivers:
New drivers
- Freescale MPL3115A2 Pressure / temperature sensor
New functionality
- hid_sensors: add sensitivity support.
DT bindings
- tsl2563
- hmc5843
Cleanups
- Drop unused scan_type from viperboard adc driver.
- devm_iio_device_register used in viperboard, ad5421, ad5755, adis16130,
adxrs450, vcnl4000, adis16220, ad7816, lpc32xx, adt7316, adis16060, isl29018
and ad2s1200. Note that this was proposed in a number of other drivers
and this revealed a number of missorderings in remove functions. Also for
now I have blocked this on any device that any hardware suspend suport on
the basis that we probably want to power down devices if they have no driver
support loaded.
The driver does not use poll_delay parameter, so let's remove it.
Tested-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pasting the verbatim PCI_(VENDOR|DEVICE)_* macros in the __pci_fixup_*
symbol names results in insanely long names such as
__pci_fixup_resumePCI_VENDOR_ID_SERVERWORKSPCI_DEVICE_ID_SERVERWORKS_HT1000SBquirk_disable_broadcom_boot_interrupt
When Link-Time Optimization adds its numeric suffix to such symbol, it
overflows the namebuf[KSYM_NAME_LEN] array in kernel/kallsyms.c. Use the
line number instead to create (nearly) unique symbol names.
Reported-by: Joe Mario <jmario@redhat.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
In order to support increased build test coverage for drivers, implement
dummies for the powergate implementation. This will allow the drivers to
be built without requiring support for Tegra to be selected.
This patch solves the following build errors, which can be triggered in
v3.13-rc1 by selecting DRM_TEGRA without ARCH_TEGRA:
drivers/built-in.o: In function `gr3d_remove':
drivers/gpu/drm/tegra/gr3d.c:321: undefined reference to `tegra_powergate_power_off'
drivers/gpu/drm/tegra/gr3d.c:325: undefined reference to `tegra_powergate_power_off'
drivers/built-in.o: In function `gr3d_probe':
drivers/gpu/drm/tegra/gr3d.c:266: undefined reference to `tegra_powergate_sequence_power_up'
drivers/gpu/drm/tegra/gr3d.c:273: undefined reference to `tegra_powergate_sequence_power_up'
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, updated commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJSk7SvAAoJEFSFNJnE9BaIRNsQAJnM/WiH1ghfA5nuc0V7JrnB
2Z6Qtm3Stoq4Ul5LYiEMxumo6ckL17YFddxejUF9X4Eq5N8YyAxdPd8JdDJgS2OL
yCM2x6izd9drIGA3YUMMOvZ1BScSK1e5DmXJHp4nuF68uHtf2TM4TGF/2zuqt3TN
2bL7blNF3/5O/TiBRB4XjkH4Sy5c4G2kke+0SckRnWohTn8oE7tWihr84nYPciqt
mu11Nrv9S+sr/5GzRwN8d5SU33yU2/ML32QU/4oQzb/XxBW0W759NJflqY5sSZ89
JQnHcCKKZD7IWBFT0VAMiuEjBpSRGc4vxBbYjsVHtEHzW7v3L0fvob5YqfSrzMlD
rVUiTQJm7fC/4hn7iJUPrxkWsSGsjCvVrLZmZFOK3OYONUfd+Cqg0nliihRZo65s
054/yi4v8xd6OUzqSxtWKIK/ZQjDxa5W2BlRoryShCrUAo/e3Djy+jH32v4Mmgfe
D9aEwdUqa8kPlq6pyQC2QRgWWU1K5+RRrzW5nNNLlmjYtVlfF+8OgcQYGHW8iMur
8AaDXNZwQLEYA4409T/Ar9lNg4gDqc0YZsvNibu0q4Kxfp13dJOwra+xmF+ktECr
KcIFxu5v89SgpE1Rra74OXYFWQ1I4Qy+sJxhQKymthPzmw4nuUidK33mxjtcojwz
TvQJu8f3us8Ea5vQLZo0
=cIMc
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of fixes for IIO in the 3.13 cycle.
The usual mixed bag of fixes.
* 3 cases where kconfig dependencies were missing. We need to keep a closer
eye on this in new drivers.
* hid_sensors was abusing the iio_dev->trigger pointer. We had a round
of clearing this out some time ago but this driver clearly slipped through.
* A misuse of the IIO_ST macro, in mcp3422, which we should really make a
concertive effort to finish removing.
* Avoid a double free introduced by recent buffer reference counting in the
one driver that (quite reasonably!) does things differently (am335x)
* A missing mutex_unlock in kxsd9 that means that driver has been non
functional for some time and no one noticed (including me who for once
actually has one of the supported devices).
* An incorrect assumption about the parameters of sign_extend32 in mcp3422.
So nothing controversial. The only substantial patch is the hid_sensors
one and that is actually just adding a new pointer to the devices private
state then moving the code over to it.
Introduce shift and mask defines for beamformee STS cap and number
of sounding dimensions cap as these can take any 3 bit value.
While at it also cleanup an unrequired parenthesis.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
GPIO mapping properties were defined using the GPIOF_* flags, which are
declared in linux/gpio.h. This file is not included when using the
GPIO descriptor interface.
This patch declares the flags that can be used as GPIO mappings
properties in linux/gpio/driver.h, and uses them in gpiolib, so that no
deprecated declarations are used by the GPIO descriptor interface.
This patch also allows GPIO_OPEN_DRAIN and GPIO_OPEN_SOURCE to be
specified as GPIO mapping properties.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Documentation related to function should be placed above
its implementation. Move it accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix kernel-doc warning for duplicate definition of 'kmalloc':
Documentation/DocBook/kernel-api.xml:9483: element refentry: validity error : ID API-kmalloc already defined
<refentry id="API-kmalloc">
Also combine the kernel-doc info from the 2 kmalloc definitions into one
block and remove the "see kcalloc" comment since kmalloc now contains the
@flags info.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new bio_split() can split arbitrary bios - it's not restricted to
single page bios, like the old bio_split() (previously renamed to
bio_pair_split()). It also has different semantics - it doesn't allocate
a struct bio_pair, leaving it up to the caller to handle completions.
Then convert the existing bio_pair_split() users to the new bio_split()
- and also nvme, which was open coding bio splitting.
(We have to take that BUG_ON() out of bio_integrity_trim() because this
bio_split() needs to use it, and there's no reason it has to be used on
bios marked as cloned; BIO_CLONED doesn't seem to have clearly
documented semantics anyways.)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Neil Brown <neilb@suse.de>
This is prep work for introducing a more general bio_split().
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Lars Ellenberg <lars.ellenberg@linbit.com>
Cc: Peter Osterlund <petero2@telia.com>
Cc: Sage Weil <sage@inktank.com>
This adds a generic mechanism for chaining bio completions. This is
going to be used for a bio_split() replacement, and it turns out to be
very useful in a fair amount of driver code - a fair number of drivers
were implementing this in their own roundabout ways, often painfully.
Note that this means it's no longer to call bio_endio() more than once
on the same bio! This can cause problems for drivers that save/restore
bi_end_io. Arguably they shouldn't be saving/restoring bi_end_io at all
- in all but the simplest cases they'd be better off just cloning the
bio, and immutable biovecs is making bio cloning cheaper. But for now,
we add a bio_endio_nodec() for these cases.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
We need to convert the dm code to the new bvec_iter primitives which
respect bi_bvec_done; they also allow us to drastically simplify dm's
bio splitting code.
Also, it's no longer necessary to save/restore the bvec array anymore -
driver conversions for immutable bvecs are done, so drivers should never
be modifying it.
Also kill bio_sector_offset(), dm was the only user and it doesn't make
much sense anymore.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
bio_clone() just got more expensive - however, most users of bio_clone()
don't actually need to modify the biovec. If they aren't modifying the
biovec, and they can guarantee that the original bio isn't freed before
the clone (also true in most cases), we can just point the clone at the
original bio's biovec.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
bio_iovec_idx() and __bio_iovec() don't have any valid uses anymore -
previous users have been converted to bio_iovec_iter() or other methods.
__BVEC_END() has to go too - the bvec array can't be used directly for
the last biovec because we might only be using the first portion of it,
we have to iterate over the bvec array with bio_for_each_segment() which
checks against the current value of bi_iter.bi_size.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Now that we've got a mechanism for immutable biovecs -
bi_iter.bi_bvec_done - we need to convert drivers to use primitives that
respect it instead of using the bvec array directly.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Sage Weil <sage@inktank.com>
Cc: ceph-devel@vger.kernel.org
Now that we've got a mechanism for immutable biovecs -
bi_iter.bi_bvec_done - we need to convert drivers to use primitives that
respect it instead of using the bvec array directly.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
When we start sharing biovecs, keeping bi_vcnt accurate for splits is
going to be error prone - and unnecessary, if we refactor some code.
So bio_segments() has to go - but most of the existing users just needed
to know if the bio had multiple segments, which is easier - add a
bio_multiple_segments() for them.
(Two of the current uses of bio_segments() are going to go away in a
couple patches, but the current implementation of bio_segments() is
unsafe as soon as we start doing driver conversions for immutable
biovecs - so implement a dumb version for bisectability, it'll go away
in a couple patches)
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
The bio integrity is also stored in a bvec array, so if we use the bvec
iter code we just added, the integrity code won't need to implement its
own iteration stuff (bio_integrity_mark_head(), bio_integrity_mark_tail())
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
This adds a mechanism by which we can advance a bio by an arbitrary
number of bytes without modifying the biovec: bio->bi_iter.bi_bvec_done
indicates the number of bytes completed in the current bvec.
Various driver code still needs to be updated to not refer to the bvec
directly before we can use this for interesting things, like efficient
bio splitting.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
More prep work for immutable biovecs - with immutable bvecs drivers
won't be able to use the biovec directly, they'll need to use helpers
that take into account bio->bi_iter.bi_bvec_done.
This updates callers for the new usage without changing the
implementation yet.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Quoc-Son Anh <quoc-sonx.anh@intel.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jan Kara <jack@suse.cz>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
Cc: cbe-oss-dev@lists.ozlabs.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: linux-fsdevel@vger.kernel.org
Cc: cluster-devel@redhat.com
Cc: linux-mm@kvack.org
Acked-by: Geoff Levand <geoff@infradead.org>
For immutable biovecs, we'll be introducing a new bio_iovec() that uses
our new bvec iterator to construct a biovec, taking into account
bvec_iter->bi_bvec_done - this patch updates existing users for the new
usage.
Some of the existing users really do need a pointer into the bvec array
- those uses are all going to be removed, but we'll need the
functionality from immutable to remove them - so for now rename the
existing bio_iovec() -> __bio_iovec(), and it'll be removed in a couple
patches.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Pull crypto update from Herbert Xu:
- Made x86 ablk_helper generic for ARM
- Phase out chainiv in favour of eseqiv (affects IPsec)
- Fixed aes-cbc IV corruption on s390
- Added constant-time crypto_memneq which replaces memcmp
- Fixed aes-ctr in omap-aes
- Added OMAP3 ROM RNG support
- Add PRNG support for MSM SoC's
- Add and use Job Ring API in caam
- Misc fixes
[ NOTE! This pull request was sent within the merge window, but Herbert
has some questionable email sending setup that makes him public enemy
#1 as far as gmail is concerned. So most of his emails seem to be
trapped by gmail as spam, resulting in me not seeing them. - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (49 commits)
crypto: s390 - Fix aes-cbc IV corruption
crypto: omap-aes - Fix CTR mode counter length
crypto: omap-sham - Add missing modalias
padata: make the sequence counter an atomic_t
crypto: caam - Modify the interface layers to use JR API's
crypto: caam - Add API's to allocate/free Job Rings
crypto: caam - Add Platform driver for Job Ring
hwrng: msm - Add PRNG support for MSM SoC's
ARM: DT: msm: Add Qualcomm's PRNG driver binding document
crypto: skcipher - Use eseqiv even on UP machines
crypto: talitos - Simplify key parsing
crypto: picoxcell - Simplify and harden key parsing
crypto: ixp4xx - Simplify and harden key parsing
crypto: authencesn - Simplify key parsing
crypto: authenc - Export key parsing helper function
crypto: mv_cesa: remove deprecated IRQF_DISABLED
hwrng: OMAP3 ROM Random Number Generator support
crypto: sha256_ssse3 - also test for BMI2
crypto: mv_cesa - Remove redundant of_match_ptr
crypto: sahara - Remove redundant of_match_ptr
...
Merge v3.12 based patch series to move cgroup_event implementation to
memcg into for-3.14. The following two commits cause a conflict in
kernel/cgroup.c
2ff2a7d03b ("cgroup: kill css_id")
79bd9814e5 ("cgroup, memcg: move cgroup_event implementation to memcg")
Each patch removes a struct definition from kernel/cgroup.c. As the
two are adjacent, they cause a context conflict. Easily resolved by
removing both structs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Now that cgroup_event is made memcg specific, the temporarily exported
functions are no longer necessary. Unexport cgroup_css() and remove
__file_cft() which doesn't have any user left.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
cgroup_event is now memcg specific. Replace cgroup_event->css with
->memcg and convert [un]register_event() callbacks to take mem_cgroup
pointer instead of cgroup_subsys_state one. This simplifies the code
slightly and makes css_to_vmpressure() unnecessary which is removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
The only use of cgroup_event->cft is distinguishing "usage_in_bytes"
and "memsw.usgae_in_bytes" for mem_cgroup_usage_[un]register_event(),
which can be done by adding an explicit argument to the function and
implementing two wrappers so that the two cases can be distinguished
from the function alone.
Remove cgroup_event->cft and the related code including
[un]register_events() methods.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
cgroup_event is being moved from cgroup core to memcg and the
implementation is already moved by the previous patch. This patch
moves the data fields and callbacks.
* cgroup->event_list[_lock] are moved to mem_cgroup.
* cftype->[un]register_event() are moved to cgroup_event. This makes
it impossible for individual cftype definitions to specify their
event callbacks. This is worked around by simply hard-coding
filename to event callback mapping in cgroup_write_event_control().
This is awkward and inflexible, which is actually desirable given
that we don't want to grow more usages of this feature.
* eventfd_ctx declaration is removed from cgroup.h, which makes
vmpressure.h miss eventfd_ctx declaration. Include eventfd.h from
vmpressure.h.
v2: Use file name from dentry instead of cftype. This will allow
removing all cftype handling in the function.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
cgroup_event is way over-designed and tries to build a generic
flexible event mechanism into cgroup - fully customizable event
specification for each user of the interface. This is utterly
unnecessary and overboard especially in the light of the planned
unified hierarchy as there's gonna be single agent. Simply generating
events at fixed points, or if that's too restrictive, configureable
cadence or single set of configureable points should be enough.
Thankfully, memcg is the only user and gets to keep it. Replacing it
with something simpler on sane_behavior is strongly recommended.
This patch moves cgroup_event and "cgroup.event_control"
implementation to mm/memcontrol.c. Clearing of events on cgroup
destruction is moved from cgroup_destroy_locked() to
mem_cgroup_css_offline(), which shouldn't make any noticeable
difference.
cgroup_css() and __file_cft() are exported to enable the move;
however, this will soon be reverted once the event code is updated to
be memcg specific.
Note that "cgroup.event_control" will now exist only on the hierarchy
with memcg attached to it. While this change is visible to userland,
it is unlikely to be noticeable as the file has never been meaningful
outside memcg.
Aside from the above change, this is pure code relocation.
v2: Per Li Zefan's comments, init/Kconfig updated accordingly and
poll.h inclusion moved from cgroup.c to memcontrol.c.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Balbir Singh <bsingharora@gmail.com>
Pull networking fixes from David Miller:
1) Fix memory leaks and other issues in mwifiex driver, from Amitkumar
Karwar.
2) skb_segment() can choke on packets using frag lists, fix from
Herbert Xu with help from Eric Dumazet and others.
3) IPv4 output cached route instantiation properly handles races
involving two threads trying to install the same route, but we
forgot to propagate this logic to input routes as well. Fix from
Alexei Starovoitov.
4) Put protections in place to make sure that recvmsg() paths never
accidently copy uninitialized memory back into userspace and also
make sure that we never try to use more that sockaddr_storage for
building the on-kernel-stack copy of a sockaddr. Fixes from Hannes
Frederic Sowa.
5) R8152 driver transmit flow bug fixes from Hayes Wang.
6) Fix some minor fallouts from genetlink changes, from Johannes Berg
and Michael Opdenacker.
7) AF_PACKET sendmsg path can race with netdevice unregister notifier,
fix by using RCU to make sure the network device doesn't go away
from under us. Fix from Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
gso: handle new frag_list of frags GRO packets
genetlink: fix genl_set_err() group ID
genetlink: fix genlmsg_multicast() bug
packet: fix use after free race in send path when dev is released
xen-netback: stop the VIF thread before unbinding IRQs
wimax: remove dead code
net/phy: Add the autocross feature for forced links on VSC82x4
net/phy: Add VSC8662 support
net/phy: Add VSC8574 support
net/phy: Add VSC8234 support
net: add BUG_ON if kernel advertises msg_namelen > sizeof(struct sockaddr_storage)
net: rework recvmsg handler msg_name and msg_namelen logic
bridge: flush br's address entry in fdb when remove the
net: core: Always propagate flag changes to interfaces
ipv4: fix race in concurrent ip_route_input_slow()
r8152: fix incorrect type in assignment
r8152: support stopping/waking tx queue
r8152: modify the tx flow
r8152: fix tx/rx memory overflow
netfilter: ebt_ip6: fix source and destination matching
...
Pull SLAB changes from Pekka Enberg:
"The patches from Joonsoo Kim switch mm/slab.c to use 'struct page' for
slab internals similar to mm/slub.c. This reduces memory usage and
improves performance:
https://lkml.org/lkml/2013/10/16/155
Rest of the changes are bug fixes from various people"
* 'slab/next' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: (21 commits)
mm, slub: fix the typo in mm/slub.c
mm, slub: fix the typo in include/linux/slub_def.h
slub: Handle NULL parameter in kmem_cache_flags
slab: replace non-existing 'struct freelist *' with 'void *'
slab: fix to calm down kmemleak warning
slub: proper kmemleak tracking if CONFIG_SLUB_DEBUG disabled
slab: rename slab_bufctl to slab_freelist
slab: remove useless statement for checking pfmemalloc
slab: use struct page for slab management
slab: replace free and inuse in struct slab with newly introduced active
slab: remove SLAB_LIMIT
slab: remove kmem_bufctl_t
slab: change the management method of free objects of the slab
slab: use __GFP_COMP flag for allocating slab pages
slab: use well-defined macro, virt_to_slab()
slab: overloading the RCU head over the LRU for RCU free
slab: remove cachep in struct slab_rcu
slab: remove nodeid in struct slab
slab: remove colouroff in struct slab
slab: change return type of kmem_getpages() to struct page
...
Merge patches from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: place page->pmd_huge_pte to right union
MAINTAINERS: add keyboard driver to Hyper-V file list
x86, mm: do not leak page->ptl for pmd page tables
ipc,shm: correct error return value in shmctl (SHM_UNLOCK)
mm, mempolicy: silence gcc warning
block/partitions/efi.c: fix bound check
ARM: drivers/rtc/rtc-at91rm9200.c: disable interrupts at shutdown
mm: hugetlbfs: fix hugetlbfs optimization
kernel: remove CONFIG_USE_GENERIC_SMP_HELPERS cleanly
ipc,shm: fix shm_file deletion races
mm: thp: give transparent hugepage code a separate copy_page
checkpatch: fix "Use of uninitialized value" warnings
configfs: fix race between dentry put and lookup
Pull security subsystem updates from James Morris:
"In this patchset, we finally get an SELinux update, with Paul Moore
taking over as maintainer of that code.
Also a significant update for the Keys subsystem, as well as
maintenance updates to Smack, IMA, TPM, and Apparmor"
and since I wanted to know more about the updates to key handling,
here's the explanation from David Howells on that:
"Okay. There are a number of separate bits. I'll go over the big bits
and the odd important other bit, most of the smaller bits are just
fixes and cleanups. If you want the small bits accounting for, I can
do that too.
(1) Keyring capacity expansion.
KEYS: Consolidate the concept of an 'index key' for key access
KEYS: Introduce a search context structure
KEYS: Search for auth-key by name rather than target key ID
Add a generic associative array implementation.
KEYS: Expand the capacity of a keyring
Several of the patches are providing an expansion of the capacity of a
keyring. Currently, the maximum size of a keyring payload is one page.
Subtract a small header and then divide up into pointers, that only gives
you ~500 pointers on an x86_64 box. However, since the NFS idmapper uses
a keyring to store ID mapping data, that has proven to be insufficient to
the cause.
Whatever data structure I use to handle the keyring payload, it can only
store pointers to keys, not the keys themselves because several keyrings
may point to a single key. This precludes inserting, say, and rb_node
struct into the key struct for this purpose.
I could make an rbtree of records such that each record has an rb_node
and a key pointer, but that would use four words of space per key stored
in the keyring. It would, however, be able to use much existing code.
I selected instead a non-rebalancing radix-tree type approach as that
could have a better space-used/key-pointer ratio. I could have used the
radix tree implementation that we already have and insert keys into it by
their serial numbers, but that means any sort of search must iterate over
the whole radix tree. Further, its nodes are a bit on the capacious side
for what I want - especially given that key serial numbers are randomly
allocated, thus leaving a lot of empty space in the tree.
So what I have is an associative array that internally is a radix-tree
with 16 pointers per node where the index key is constructed from the key
type pointer and the key description. This means that an exact lookup by
type+description is very fast as this tells us how to navigate directly to
the target key.
I made the data structure general in lib/assoc_array.c as far as it is
concerned, its index key is just a sequence of bits that leads to a
pointer. It's possible that someone else will be able to make use of it
also. FS-Cache might, for example.
(2) Mark keys as 'trusted' and keyrings as 'trusted only'.
KEYS: verify a certificate is signed by a 'trusted' key
KEYS: Make the system 'trusted' keyring viewable by userspace
KEYS: Add a 'trusted' flag and a 'trusted only' flag
KEYS: Separate the kernel signature checking keyring from module signing
These patches allow keys carrying asymmetric public keys to be marked as
being 'trusted' and allow keyrings to be marked as only permitting the
addition or linkage of trusted keys.
Keys loaded from hardware during kernel boot or compiled into the kernel
during build are marked as being trusted automatically. New keys can be
loaded at runtime with add_key(). They are checked against the system
keyring contents and if their signatures can be validated with keys that
are already marked trusted, then they are marked trusted also and can
thus be added into the master keyring.
Patches from Mimi Zohar make this usable with the IMA keyrings also.
(3) Remove the date checks on the key used to validate a module signature.
X.509: Remove certificate date checks
It's not reasonable to reject a signature just because the key that it was
generated with is no longer valid datewise - especially if the kernel
hasn't yet managed to set the system clock when the first module is
loaded - so just remove those checks.
(4) Make it simpler to deal with additional X.509 being loaded into the kernel.
KEYS: Load *.x509 files into kernel keyring
KEYS: Have make canonicalise the paths of the X.509 certs better to deduplicate
The builder of the kernel now just places files with the extension ".x509"
into the kernel source or build trees and they're concatenated by the
kernel build and stuffed into the appropriate section.
(5) Add support for userspace kerberos to use keyrings.
KEYS: Add per-user_namespace registers for persistent per-UID kerberos caches
KEYS: Implement a big key type that can save to tmpfs
Fedora went to, by default, storing kerberos tickets and tokens in tmpfs.
We looked at storing it in keyrings instead as that confers certain
advantages such as tickets being automatically deleted after a certain
amount of time and the ability for the kernel to get at these tokens more
easily.
To make this work, two things were needed:
(a) A way for the tickets to persist beyond the lifetime of all a user's
sessions so that cron-driven processes can still use them.
The problem is that a user's session keyrings are deleted when the
session that spawned them logs out and the user's user keyring is
deleted when the UID is deleted (typically when the last log out
happens), so neither of these places is suitable.
I've added a system keyring into which a 'persistent' keyring is
created for each UID on request. Each time a user requests their
persistent keyring, the expiry time on it is set anew. If the user
doesn't ask for it for, say, three days, the keyring is automatically
expired and garbage collected using the existing gc. All the kerberos
tokens it held are then also gc'd.
(b) A key type that can hold really big tickets (up to 1MB in size).
The problem is that Active Directory can return huge tickets with lots
of auxiliary data attached. We don't, however, want to eat up huge
tracts of unswappable kernel space for this, so if the ticket is
greater than a certain size, we create a swappable shmem file and dump
the contents in there and just live with the fact we then have an
inode and a dentry overhead. If the ticket is smaller than that, we
slap it in a kmalloc()'d buffer"
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (121 commits)
KEYS: Fix keyring content gc scanner
KEYS: Fix error handling in big_key instantiation
KEYS: Fix UID check in keyctl_get_persistent()
KEYS: The RSA public key algorithm needs to select MPILIB
ima: define '_ima' as a builtin 'trusted' keyring
ima: extend the measurement list to include the file signature
kernel/system_certificate.S: use real contents instead of macro GLOBAL()
KEYS: fix error return code in big_key_instantiate()
KEYS: Fix keyring quota misaccounting on key replacement and unlink
KEYS: Fix a race between negating a key and reading the error set
KEYS: Make BIG_KEYS boolean
apparmor: remove the "task" arg from may_change_ptraced_domain()
apparmor: remove parent task info from audit logging
apparmor: remove tsk field from the apparmor_audit_struct
apparmor: fix capability to not use the current task, during reporting
Smack: Ptrace access check mode
ima: provide hash algo info in the xattr
ima: enable support for larger default filedata hash algorithms
ima: define kernel parameter 'ima_template=' to change configured default
ima: add Kconfig default measurement list template
...
Pull audit updates from Eric Paris:
"Nothing amazing. Formatting, small bug fixes, couple of fixes where
we didn't get records due to some old VFS changes, and a change to how
we collect execve info..."
Fixed conflict in fs/exec.c as per Eric and linux-next.
* git://git.infradead.org/users/eparis/audit: (28 commits)
audit: fix type of sessionid in audit_set_loginuid()
audit: call audit_bprm() only once to add AUDIT_EXECVE information
audit: move audit_aux_data_execve contents into audit_context union
audit: remove unused envc member of audit_aux_data_execve
audit: Kill the unused struct audit_aux_data_capset
audit: do not reject all AUDIT_INODE filter types
audit: suppress stock memalloc failure warnings since already managed
audit: log the audit_names record type
audit: add child record before the create to handle case where create fails
audit: use given values in tty_audit enable api
audit: use nlmsg_len() to get message payload length
audit: use memset instead of trying to initialize field by field
audit: fix info leak in AUDIT_GET requests
audit: update AUDIT_INODE filter rule to comparator function
audit: audit feature to set loginuid immutable
audit: audit feature to only allow unsetting the loginuid
audit: allow unsetting the loginuid (with priv)
audit: remove CONFIG_AUDIT_LOGINUID_IMMUTABLE
audit: loginuid functions coding style
selinux: apply selinux checks on new audit message types
...
I don't know what went wrong, mis-merge or something, but ->pmd_huge_pte
placed in wrong union within struct page.
In original patch[1] it's placed to union with ->lru and ->slab, but in
commit e009bb30c8 ("mm: implement split page table lock for PMD
level") it's in union with ->index and ->freelist.
That union seems also unused for pages with table tables and safe to
re-use, but it's not what I've tested.
Let's move it to original place. It fixes indentation at least. :)
[1] https://lkml.org/lkml/2013/10/7/288
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 7cb2ef56e6 ("mm: fix aio performance regression for database
caused by THP") can cause dereference of a dangling pointer if
split_huge_page runs during PageHuge() if there are updates to the
tail_page->private field.
Also it is repeating compound_head twice for hugetlbfs and it is running
compound_head+compound_trans_head for THP when a single one is needed in
both cases.
The new code within the PageSlab() check doesn't need to verify that the
THP page size is never bigger than the smallest hugetlbfs page size, to
avoid memory corruption.
A longstanding theoretical race condition was found while fixing the
above (see the change right after the skip_unlock label, that is
relevant for the compound_lock path too).
By re-establishing the _mapcount tail refcounting for all compound
pages, this also fixes the below problem:
echo 0 >/sys/kernel/mm/hugepages/hugepages-2048kB/nr_hugepages
BUG: Bad page state in process bash pfn:59a01
page:ffffea000139b038 count:0 mapcount:10 mapping: (null) index:0x0
page flags: 0x1c00000000008000(tail)
Modules linked in:
CPU: 6 PID: 2018 Comm: bash Not tainted 3.12.0+ #25
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x55/0x76
bad_page+0xd5/0x130
free_pages_prepare+0x213/0x280
__free_pages+0x36/0x80
update_and_free_page+0xc1/0xd0
free_pool_huge_page+0xc2/0xe0
set_max_huge_pages.part.58+0x14c/0x220
nr_hugepages_store_common.isra.60+0xd0/0xf0
nr_hugepages_store+0x13/0x20
kobj_attr_store+0xf/0x20
sysfs_write_file+0x189/0x1e0
vfs_write+0xc5/0x1f0
SyS_write+0x55/0xb0
system_call_fastpath+0x16/0x1b
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now, the migration code in migrate_page_copy() uses copy_huge_page()
for hugetlbfs and thp pages:
if (PageHuge(page) || PageTransHuge(page))
copy_huge_page(newpage, page);
So, yay for code reuse. But:
void copy_huge_page(struct page *dst, struct page *src)
{
struct hstate *h = page_hstate(src);
and a non-hugetlbfs page has no page_hstate(). This works 99% of the
time because page_hstate() determines the hstate from the page order
alone. Since the page order of a THP page matches the default hugetlbfs
page order, it works.
But, if you change the default huge page size on the boot command-line
(say default_hugepagesz=1G), then we might not even *have* a 2MB hstate
so page_hstate() returns null and copy_huge_page() oopses pretty fast
since copy_huge_page() dereferences the hstate:
void copy_huge_page(struct page *dst, struct page *src)
{
struct hstate *h = page_hstate(src);
if (unlikely(pages_per_huge_page(h) > MAX_ORDER_NR_PAGES)) {
...
Mel noticed that the migration code is really the only user of these
functions. This moves all the copy code over to migrate.c and makes
copy_huge_page() work for THP by checking for it explicitly.
I believe the bug was introduced in commit b32967ff10 ("mm: numa: Add
THP migration for the NUMA working set scanning fault case")
[akpm@linux-foundation.org: fix coding-style and comment text, per Naoya Horiguchi]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSjfuVAAoJEFGvii+H/HdhOYsP/2lrz6GLYBgQFp9H+6t95+8H
KvFmefaM5pjoBdnq6Q7pZBxYO4m15J3TaFNzH+Ib6oWJlg/awpu1Qwu5+Pwwv9RK
6x4mEyy9yDu2CJd+6wpBFxx1Ujj4CdAq5dm/bUMiCr0d4Ez2qZhxdiDPGB02QHv7
J7KkJBnG0PSiV4uoiLh8pOQsCF+v5y1l0rUaI3ZG+7x2QAi9I3liZGBI02BVvXsh
/0aYWc8xQUar1JurPNVN4I6cojyKp5oyq4SHkpdbkk3Yt7ek1aNoPMG6ORqvaEMn
5WF7LISpFF1NrHifW5SUdnbx5dxOnZyKRRgEWcP1TMZEmSJ4mdYFbqgMIJCJuRCN
k23mVQEcQYy+1V8CuymhMuIB4SBiNYLpbJ7bvQ/Q5N34yuVl9eqPxshcVgAUhFkc
8+vZj+/be+lpxw4zhIrAS0IlEVjUvMs8/B/kmCfcKPID5zPLUWPVbxGRSPMDEpzS
liR7uw94/LHUiW3JD7I1x2MchjK7sH55p22hZJFhqUcU0LjcFfY0+3mz0ljAuPZt
BZrt1O3yW987m6WXVZmJDI10h0feh1K8TlpnnL3ppWO4cKsgoB7wruYxQtptVyZR
wzN0rq6UyianNMIGHWYgHQ7ye8wzeazMZWTQLl8AblIJ3xXozsmLScKBHJGXgeKh
jafyhkX8wFiEoEMGWW5G
=IhEz
-----END PGP SIGNATURE-----
Merge tag 'ib-asoc-1' of git://git.linaro.org/people/ljones/mfd into asoc-arizona
Immutable branch for ASoC, as requested by Mark Brown
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add auto-MDI/MDI-X capability for forced (autonegotiation disabled)
10/100 Mbps speeds on Vitesse VSC82x4 PHYs. Exported previously static
function genphy_setup_forced() required by the new config_aneg handler
in the Vitesse PHY module.
Signed-off-by: Madalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: Shruti Kanetkar <Shruti@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch now always passes msg->msg_namelen as 0. recvmsg handlers must
set msg_namelen to the proper size <= sizeof(struct sockaddr_storage)
to return msg_name to the user.
This prevents numerous uninitialized memory leaks we had in the
recvmsg handlers and makes it harder for new code to accidentally leak
uninitialized memory.
Optimize for the case recvfrom is called with NULL as address. We don't
need to copy the address at all, so set it to NULL before invoking the
recvmsg handler. We can do so, because all the recvmsg handlers must
cope with the case a plain read() is called on them. read() also sets
msg_name to NULL.
Also document these changes in include/linux/net.h as suggested by David
Miller.
Changes since RFC:
Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address. It also more naturally reflects the logic by the callers of
verify_iovec.
With this change in place I could remove "
if (!uaddr || msg_sys->msg_namelen == 0)
msg->msg_name = NULL
".
This change does not alter the user visible error logic as we ignore
msg_namelen as long as msg_name is NULL.
Also remove two unnecessary curly brackets in ___sys_recvmsg and change
comments to netdev style.
Cc: David Miller <davem@davemloft.net>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ea1e7ed337.
Al points out that while the commit *does* actually create a separate
slab for the page->ptl allocation, that slab is never actually used, and
the code continues to use kmalloc/kfree.
Damien Wyart points out that the original patch did have the conversion
to use kmem_cache_alloc/free, so it got lost somewhere on its way to me.
Revert the half-arsed attempt that didn't do anything. If we really do
want the special slab (remember: this is all relevant just for debug
builds, so it's not necessarily all that critical) we might as well redo
the patch fully.
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Kirill A Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs bits and pieces from Al Viro:
"Assorted bits that got missed in the first pull request + fixes for a
couple of coredump regressions"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fold try_to_ascend() into the sole remaining caller
dcache.c: get rid of pointless macros
take read_seqbegin_or_lock() and friends to seqlock.h
consolidate simple ->d_delete() instances
gfs2: endianness misannotations
dump_emit(): use __kernel_write(), not vfs_write()
dump_align(): fix the dumb braino
- ACPI-based device hotplug fixes for issues introduced recently and
a fix for an older error code path bug in the ACPI PCI host bridge
driver.
- Fix for recently broken OMAP cpufreq build from Viresh Kumar.
- Fix for a recent hibernation regression related to s2disk.
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar.
- System suspend error code path fix related to runtime PM and
runtime PM documentation update from Ulf Hansson.
- cpufreq's conservative governor fix from Xiaoguang Chen.
- New processor IDs for intel_idle and turbostat and removal of
an obsolete Kconfig option from Len Brown.
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg.
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu.
- Rework of the ACPI companion representation in struct device and
code cleanup related to that change from Rafael J Wysocki,
Lan Tianyu and Jarkko Nikula.
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices
from Jarkko Nikula.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=QMp+
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
- ACPI-based device hotplug fixes for issues introduced recently and a
fix for an older error code path bug in the ACPI PCI host bridge
driver
- Fix for recently broken OMAP cpufreq build from Viresh Kumar
- Fix for a recent hibernation regression related to s2disk
- Fix for a locking-related regression in the ACPI EC driver from
Puneet Kumar
- System suspend error code path fix related to runtime PM and runtime
PM documentation update from Ulf Hansson
- cpufreq's conservative governor fix from Xiaoguang Chen
- New processor IDs for intel_idle and turbostat and removal of an
obsolete Kconfig option from Len Brown
- New device IDs for the ACPI LPSS (Low-Power Subsystem) driver and
ACPI-based PCI hotplug (ACPIPHP) cleanup from Mika Westerberg
- Removal of several ACPI video DMI blacklist entries that are not
necessary any more from Aaron Lu
- Rework of the ACPI companion representation in struct device and code
cleanup related to that change from Rafael J Wysocki, Lan Tianyu and
Jarkko Nikula
- Fixes for assigning names to ACPI-enumerated I2C and SPI devices from
Jarkko Nikula
* tag 'pm+acpi-2-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (24 commits)
PCI / hotplug / ACPI: Drop unused acpiphp_debug declaration
ACPI / scan: Set flags.match_driver in acpi_bus_scan_fixed()
ACPI / PCI root: Clear driver_data before failing enumeration
ACPI / hotplug: Fix PCI host bridge hot removal
ACPI / hotplug: Fix acpi_bus_get_device() return value check
cpufreq: governor: Remove fossil comment in the cpufreq_governor_dbs()
ACPI / video: clean up DMI table for initial black screen problem
ACPI / EC: Ensure lock is acquired before accessing ec struct members
PM / Hibernate: Do not crash kernel in free_basic_memory_bitmaps()
ACPI / AC: Remove struct acpi_device pointer from struct acpi_ac
spi: Use stable dev_name for ACPI enumerated SPI slaves
i2c: Use stable dev_name for ACPI enumerated I2C slaves
ACPI: Provide acpi_dev_name accessor for struct acpi_device device name
ACPI / bind: Use (put|get)_device() on ACPI device objects too
ACPI: Eliminate the DEVICE_ACPI_HANDLE() macro
ACPI / driver core: Store an ACPI device pointer in struct acpi_dev_node
cpufreq: OMAP: Fix compilation error 'r & ret undeclared'
PM / Runtime: Fix error path for prepare
PM / Runtime: Update documentation around probe|remove|suspend
cpufreq: conservative: set requested_freq to policy max when it is over policy max
...
Pull slave-dmaengine changes from Vinod Koul:
"This brings for slave dmaengine:
- Change dma notification flag to DMA_COMPLETE from DMA_SUCCESS as
dmaengine can only transfer and not verify validaty of dma
transfers
- Bunch of fixes across drivers:
- cppi41 driver fixes from Daniel
- 8 channel freescale dma engine support and updated bindings from
Hongbo
- msx-dma fixes and cleanup by Markus
- DMAengine updates from Dan:
- Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
- In the course of testing 1/ a collection of enhancements to
dmatest fell out. Notably basic performance statistics, and
fixed / enhanced test control through new module parameters
'run', 'wait', 'noverify', and 'verbose'. Thanks to Andriy and
Linus [Walleij] for their review.
- Testing the raid related corner cases of 1/ triggered bugs in
the recently added 16-source operation support in the ioatdma
driver.
- Some minor fixes / cleanups to mv_xor and ioatdma"
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (99 commits)
dma: mv_xor: Fix mis-usage of mmio 'base' and 'high_base' registers
dma: mv_xor: Remove unneeded NULL address check
ioat: fix ioat3_irq_reinit
ioat: kill msix_single_vector support
raid6test: add new corner case for ioatdma driver
ioatdma: clean up sed pool kmem_cache
ioatdma: fix selection of 16 vs 8 source path
ioatdma: fix sed pool selection
ioatdma: Fix bug in selftest after removal of DMA_MEMSET.
dmatest: verbose mode
dmatest: convert to dmaengine_unmap_data
dmatest: add a 'wait' parameter
dmatest: add basic performance metrics
dmatest: add support for skipping verification and random data setup
dmatest: use pseudo random numbers
dmatest: support xor-only, or pq-only channels in tests
dmatest: restore ability to start test at module load and init
dmatest: cleanup redundant "dmatest: " prefixes
dmatest: replace stored results mechanism, with uniform messages
Revert "dmatest: append verify result to results"
...
Pull block IO fixes from Jens Axboe:
"Normally I'd defer my initial for-linus pull request until after the
merge window, but a race was uncovered in the virtio-blk conversion to
blk-mq that could cause hangs. So here's a small collection of fixes
for you to pull:
- The fix for the virtio-blk IO hang reported by Dave Chinner, from
Shaohua and myself.
- Add the Insert blktrace event for blk-mq. This makes 'btt' happy
when it is doing it's state transition analysis.
- Ensure that blk-mq has disk/partition stats enabled by default,
instead of making it opt-in.
- A fix for __bio_add_page() and large sector counts"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: add blktrace insert event trace
virtio-blk: virtqueue_kick() must be ordered with other virtqueue operations
blk-mq: ensure that we set REQ_IO_STAT so diskstats work
bio: fix argument of __bio_add_page() for max_sectors > 0xffff
Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io
during resync.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8RCg
-----END PGP SIGNATURE-----
Merge tag 'md/3.13' of git://neil.brown.name/md
Pull md update from Neil Brown:
"Mostly optimisations and obscure bug fixes.
- raid5 gets less lock contention
- raid1 gets less contention between normal-io and resync-io during
resync"
* tag 'md/3.13' of git://neil.brown.name/md:
md/raid5: Use conf->device_lock protect changing of multi-thread resources.
md/raid5: Before freeing old multi-thread worker, it should flush them.
md/raid5: For stripe with R5_ReadNoMerge, we replace REQ_FLUSH with REQ_NOMERGE.
UAPI: include <asm/byteorder.h> in linux/raid/md_p.h
raid1: Rewrite the implementation of iobarrier.
raid1: Add some macros to make code clearly.
raid1: Replace raise_barrier/lower_barrier with freeze_array/unfreeze_array when reconfiguring the array.
raid1: Add a field array_frozen to indicate whether raid in freeze state.
md: Convert use of typedef ctl_table to struct ctl_table
md/raid5: avoid deadlock when raid5 array has unack badblocks during md_stop_writes.
md: use MD_RECOVERY_INTR instead of kthread_should_stop in resync thread.
md: fix some places where mddev_lock return value is not checked.
raid5: Retry R5_ReadNoMerge flag when hit a read error.
raid5: relieve lock contention in get_active_stripe()
raid5: relieve lock contention in get_active_stripe()
wait: add wait_event_cmd()
md/raid5.c: add proper locking to error path of raid5_start_reshape.
md: fix calculation of stacking limits on level change.
raid5: Use slow_path to release stripe when mddev->thread is null
1. Don't include asm/uprobes.h unconditionally, we only need
it if CONFIG_UPROBES.
2. Move the definition of "struct xol_area" into uprobes.c.
Perhaps we should simply kill struct uprobes_state, it buys
nothing.
3. Kill the dummy definition of uprobe_get_swbp_addr(), nobody
except handle_swbp() needs it.
4. Purely cosmetic, but move the decl of uprobe_get_swbp_addr()
up, close to other __weak helpers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
uprobe_task->vaddr is a bit strange. The generic code uses it only
to pass the additional argument to arch_uprobe_pre_xol(), and since
it is always equal to instruction_pointer() this looks even more
strange.
And both utask->vaddr and and utask->autask have the same scope,
they only have the meaning when the task executes the probed insn
out-of-line, so it is safe to reuse both in UTASK_RUNNING state.
This all means that logically ->vaddr belongs to arch_uprobe_task
and we should probably move it there, arch_uprobe_pre_xol() can
record instruction_pointer() itself.
OTOH, it is also used by uprobe_copy_process() and dup_xol_work()
for another purpose, this doesn't look clean and doesn't allow to
move this member into arch_uprobe_task.
This patch adds the union with 2 anonymous structs into uprobe_task.
The first struct is autask + vaddr, this way we "almost" move vaddr
into autask.
The second struct has 2 new members for uprobe_copy_process() paths:
->dup_xol_addr which can be used instead ->vaddr, and ->dup_xol_work
which can be used to avoid kmalloc() and simplify the code.
Note that this union will likely have another member(s), we need
something like "private_data_for_handlers" so that the tracing
handlers could use it to communicate with call_fetch() methods.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: D.J. Barrow <dbarrow@wolfsonmicro.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull networking fixes from David Miller:
"Mostly these are fixes for fallout due to merge window changes, as
well as cures for problems that have been with us for a much longer
period of time"
1) Johannes Berg noticed two major deficiencies in our genetlink
registration. Some genetlink protocols we passing in constant
counts for their ops array rather than something like
ARRAY_SIZE(ops) or similar. Also, some genetlink protocols were
using fixed IDs for their multicast groups.
We have to retain these fixed IDs to keep existing userland tools
working, but reserve them so that other multicast groups used by
other protocols can not possibly conflict.
In dealing with these two problems, we actually now use less state
management for genetlink operations and multicast groups.
2) When configuring interface hardware timestamping, fix several
drivers that simply do not validate that the hwtstamp_config value
is one the driver actually supports. From Ben Hutchings.
3) Invalid memory references in mwifiex driver, from Amitkumar Karwar.
4) In dev_forward_skb(), set the skb->protocol in the right order
relative to skb_scrub_packet(). From Alexei Starovoitov.
5) Bridge erroneously fails to use the proper wrapper functions to make
calls to netdev_ops->ndo_vlan_rx_{add,kill}_vid. Fix from Toshiaki
Makita.
6) When detaching a bridge port, make sure to flush all VLAN IDs to
prevent them from leaking, also from Toshiaki Makita.
7) Put in a compromise for TCP Small Queues so that deep queued devices
that delay TX reclaim non-trivially don't have such a performance
decrease. One particularly problematic area is 802.11 AMPDU in
wireless. From Eric Dumazet.
8) Fix crashes in tcp_fastopen_cache_get(), we can see NULL socket dsts
here. Fix from Eric Dumzaet, reported by Dave Jones.
9) Fix use after free in ipv6 SIT driver, from Willem de Bruijn.
10) When computing mergeable buffer sizes, virtio-net fails to take the
virtio-net header into account. From Michael Dalton.
11) Fix seqlock deadlock in ip4_datagram_connect() wrt. statistic
bumping, this one has been with us for a while. From Eric Dumazet.
12) Fix NULL deref in the new TIPC fragmentation handling, from Erik
Hugne.
13) 6lowpan bit used for traffic classification was wrong, from Jukka
Rissanen.
14) macvlan has the same issue as normal vlans did wrt. propagating LRO
disabling down to the real device, fix it the same way. From Michal
Kubecek.
15) CPSW driver needs to soft reset all slaves during suspend, from
Daniel Mack.
16) Fix small frame pacing in FQ packet scheduler, from Eric Dumazet.
17) The xen-netfront RX buffer refill timer isn't properly scheduled on
partial RX allocation success, from Ma JieYue.
18) When ipv6 ping protocol support was added, the AF_INET6 protocol
initialization cleanup path on failure was borked a little. Fix
from Vlad Yasevich.
19) If a socket disconnects during a read/recvmsg/recvfrom/etc that
blocks we can do the wrong thing with the msg_name we write back to
userspace. From Hannes Frederic Sowa. There is another fix in the
works from Hannes which will prevent future problems of this nature.
20) Fix route leak in VTI tunnel transmit, from Fan Du.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (106 commits)
genetlink: make multicast groups const, prevent abuse
genetlink: pass family to functions using groups
genetlink: add and use genl_set_err()
genetlink: remove family pointer from genl_multicast_group
genetlink: remove genl_unregister_mc_group()
hsr: don't call genl_unregister_mc_group()
quota/genetlink: use proper genetlink multicast APIs
drop_monitor/genetlink: use proper genetlink multicast APIs
genetlink: only pass array to genl_register_family_with_ops()
tcp: don't update snd_nxt, when a socket is switched from repair mode
atm: idt77252: fix dev refcnt leak
xfrm: Release dst if this dst is improper for vti tunnel
netlink: fix documentation typo in netlink_set_err()
be2net: Delete secondary unicast MAC addresses during be_close
be2net: Fix unconditional enabling of Rx interface options
net, virtio_net: replace the magic value
ping: prevent NULL pointer dereference on write to msg_name
bnx2x: Prevent "timeout waiting for state X"
bnx2x: prevent CFC attention
bnx2x: Prevent panic during DMAE timeout
...
Register generic netlink multicast groups as an array with
the family and give them contiguous group IDs. Then instead
of passing the global group ID to the various functions that
send messages, pass the ID relative to the family - for most
families that's just 0 because the only have one group.
This avoids the list_head and ID in each group, adding a new
field for the mcast group ID offset to the family.
At the same time, this allows us to prevent abusing groups
again like the quota and dropmon code did, since we can now
check that a family only uses a group it owns.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This doesn't really change anything, but prepares for the
next patch that will change the APIs to pass the group ID
within the family, rather than the global group ID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As suggested by David Miller, make genl_register_family_with_ops()
a macro and pass only the array, evaluating ARRAY_SIZE() in the
macro, this is a little safer.
The openvswitch has some indirection, assing ops/n_ops directly in
that code. This might ultimately just assign the pointers in the
family initializations, saving the struct genl_family_and_ops and
code (once mcast groups are handled differently.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_NFS_V4_2 is toggled nfsd and lockd will be recompiled,
instead of only the nfs client. This patch moves a small amount of code
into the client directory to avoid unnecessary recompiles.
Signed-off-by: Anna Schumaker <bjschuma@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull irq cleanups from Ingo Molnar:
"This is a multi-arch cleanup series from Thomas Gleixner, which we
kept to near the end of the merge window, to not interfere with
architecture updates.
This series (motivated by the -rt kernel) unifies more aspects of IRQ
handling and generalizes PREEMPT_ACTIVE"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
preempt: Make PREEMPT_ACTIVE generic
sparc: Use preempt_schedule_irq
ia64: Use preempt_schedule_irq
m32r: Use preempt_schedule_irq
hardirq: Make hardirq bits generic
m68k: Simplify low level interrupt handling code
genirq: Prevent spurious detection for unconditionally polled interrupts
commit bedd30d986 ("genirq: make irqreturn_t an enum") blindly replaced
"0" by "IRQ_NONE" in the "IRQ_RETVAL(x)" macro definition.
However, as "x" is a condition, "0" meant "boolean false", not an
irqreturn_t value.
All of this worked, and kept working after the addition of IRQ_WAKE_THREAD,
as
- both "boolean false" and "IRQ_NONE" are "0" (for the comparison),
- "boolean true" and "boolean false" nicely map to the correct values of
"IRQ_HANDLED" and "IRQ_NONE" (for the return value).
Correct the macro definition for clarity and future-proofness.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If disk stats are enabled on the queue, a request needs to
be marked with REQ_IO_STAT for accounting to be active on
that request. This fixes an issue with virtio-blk not
showing up in /proc/diskstats after the conversion to
blk-mq.
Add QUEUE_FLAG_MQ_DEFAULT, setting stats and same cpu-group
completion on by default.
Reported-by: Dave Chinner <david@fromorbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Vince's perf-trinity fuzzer found yet another 'interesting' problem.
When we sample the irq_work_exit tracepoint with period==1 (or
PERF_SAMPLE_PERIOD) and we add an fasync SIGNAL handler we create an
infinite event generation loop:
,-> <IPI>
| irq_work_exit() ->
| trace_irq_work_exit() ->
| ...
| __perf_event_overflow() -> (due to fasync)
| irq_work_queue() -> (irq_work_list must be empty)
'--------- arch_irq_work_raise()
Similar things can happen due to regular poll() wakeups if we exceed
the ring-buffer wakeup watermark, or have an event_limit.
To avoid this, dis-allow sampling this particular tracepoint.
In order to achieve this, create a special perf_perm function pointer
for each event and call this (when set) on trying to create a
tracepoint perf event.
[ roasted: use expr... to allow for ',' in your expression ]
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Tested-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Dave Jones <davej@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/20131114152304.GC5364@laptop.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull i2c changes from Wolfram Sang:
- new drivers for exynos5, bcm kona, and st micro
- bigger overhauls for drivers mxs and rcar
- typical driver bugfixes, cleanups, improvements
- got rid of the superfluous 'driver' member in i2c_client struct This
touches a few drivers in other subsystems. All acked.
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: bcm-kona: fix error return code in bcm_kona_i2c_probe()
i2c: i2c-eg20t: do not print error message in syslog if no ACK received
i2c: bcm-kona: Introduce Broadcom I2C Driver
i2c: cbus-gpio: Fix device tree binding
i2c: wmt: add missing clk_disable_unprepare() on error
i2c: designware: add new ACPI IDs
i2c: i801: Add Device IDs for Intel Wildcat Point-LP PCH
i2c: exynos5: Remove incorrect clk_disable_unprepare
i2c: i2c-st: Add ST I2C controller
i2c: exynos5: add High Speed I2C controller driver
i2c: rcar: fixup rcar type naming
i2c: scmi: remove some bogus NULL checks
i2c: sh_mobile & rcar: Enable the driver on all ARM platforms
i2c: sh_mobile: Convert to clk_prepare/unprepare
i2c: mux: gpio: use reg value for i2c_add_mux_adapter
i2c: mux: gpio: use gpio_set_value_cansleep()
i2c: Include linux/of.h header
i2c: mxs: Fix PIO mode on i.MX23
i2c: mxs: Rework the PIO mode operation
i2c: mxs: distinguish i.MX23 and i.MX28 based I2C controller
...
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxC+
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=rT+j
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13' of git://git.infradead.org/battery-2.6
Pull battery updates from Anton Vorontsov:
"Highlights:
- A new driver for TI BQ24735 Battery Chargers, courtesy of NVidia.
- Device tree bindings for TWL4030 chips.
- Random fixes and cleanups"
* tag 'for-v3.13' of git://git.infradead.org/battery-2.6:
pm2301-charger: Remove unneeded NULL checks
twl4030_charger: Add devicetree support
power_supply: Fix documentation for TEMP_*ALERT* properties
max17042_battery: Support regmap to access device's registers
max17042_battery: Use SIMPLE_DEV_PM_OPS
charger-manager : Replace kzalloc to devm_kzalloc and remove uneccessary code
bq2415x_charger: Fix max battery regulation voltage
tps65090-charger: Use "IS_ENABLED(CONFIG_OF)" for DT code
tps65090-charger: Drop devm_free_irq of devm_ allocated irq
power_supply: Add support for bq24735 charger
pm2301-charger: Staticize pm2xxx_charger_die_therm_mngt
pm2301-charger: Check return value of regulator_enable
ab8500-charger: Remove redundant break
ab8500-charger: Check return value of regulator_enable
isp1704_charger: Fix driver to work with changes introduced in v3.5
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=JDGc
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.13:
Core:
- Improve runtime PM support, remove mmc_{suspend,resume}_host().
- Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're
outside of the resume sequence (in runtime_resume) to decrease
system resume time.
Drivers:
- dw_mmc: Support HS200 mode.
- sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6.
- sdhci-pci: Add support for Intel Clovertrail and Merrifield"
* tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits)
mmc: wbsd: Silence compiler warning
mmc: core: Silence compiler warning in __mmc_switch
mmc: sh_mmcif: Convert to clk_prepare|unprepare
mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops
mmc: dw_mmc: exynos: Revert the sdr_timing assignment
mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq
mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume
mmc: core: Improve runtime PM support during suspend/resume for sd/mmc
mmc: core: Remove redundant mmc_power_up|off at runtime callbacks
mmc: Don't force card to active state when entering suspend/shutdown
MIPS: db1235: Don't use MMC_CLKGATE
mmc: core: Remove deprecated mmc_suspend|resume_host APIs
mmc: mmci: Move away from using deprecated APIs
mmc: via-sdmmc: Move away from using deprecated APIs
mmc: tmio: Move away from using deprecated APIs
mmc: sh_mmcif: Move away from using deprecated APIs
mmc: sdricoh_cs: Move away from using deprecated APIs
mmc: rtsx: Remove redundant suspend and resume callbacks
mmc: wbsd: Move away from using deprecated APIs
mmc: pxamci: Remove redundant suspend and resume callbacks
...
Changes the type of dev->db_stride to unsigned and changes the value
stored there to be 1 << the current value. Then there is less
calculation to be done at completion time.
Signed-off-by: Haiyan Hu <huhaiyan@huawei.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
The only real feature that was added this release is from Namhyung Kim,
who introduced "set_graph_notrace" filter that lets you run the function
graph tracer and not trace particular functions and their call chain.
Tom Zanussi added some updates to the ftrace multibuffer tracing that
made it more consistent with the top level tracing.
One of the fixes for perf function tracing required an API change in
RCU; the addition of "rcu_is_watching()". As Paul McKenney is pushing
that change in this release too, he gave me a branch that included
all the changes to get that working, and I pulled that into my tree
in order to complete the perf function tracing fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSgX5SAAoJEKQekfcNnQGulUAH/jORqJrKaNAulmZ314VsAqfa
zMtF5UAAPf7kqc3AN/jtFrhJUNEfxWOo7A4r0FsM/rKdWJF+98GA6aqYVD+XoWFt
+36fg1enxbXUjixQ96Uh+o1+BJUgYDqljuWzqSu/oiXWfWwl8+WL4kcbhb+V9WcF
SpdzLCWVZRfhyDiN3+0zvyQ8RSG2Pd7CWn9zroI0e4sxGo0Ki6JUnIcXtZGOBDOQ
IIZdjXvGSfpJ+3u3XvRPXJcltRCtOsVWxYzrmvRlmHDW5QMe1+WmmrlojTePrLaJ
xn8+3WINqetAR+ZQnazbpt1XzJzKa8QtFgpiN0kT6qL7cg3N1Owc4vLGohl7wok=
=Nesf
-----END PGP SIGNATURE-----
Merge tag 'trace-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing update from Steven Rostedt:
"This batch of changes is mostly clean ups and small bug fixes. The
only real feature that was added this release is from Namhyung Kim,
who introduced "set_graph_notrace" filter that lets you run the
function graph tracer and not trace particular functions and their
call chain.
Tom Zanussi added some updates to the ftrace multibuffer tracing that
made it more consistent with the top level tracing.
One of the fixes for perf function tracing required an API change in
RCU; the addition of "rcu_is_watching()". As Paul McKenney is pushing
that change in this release too, he gave me a branch that included all
the changes to get that working, and I pulled that into my tree in
order to complete the perf function tracing fix"
* tag 'trace-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Add rcu annotation for syscall trace descriptors
tracing: Do not use signed enums with unsigned long long in fgragh output
tracing: Remove unused function ftrace_off_permanent()
tracing: Do not assign filp->private_data to freed memory
tracing: Add helper function tracing_is_disabled()
tracing: Open tracer when ftrace_dump_on_oops is used
tracing: Add support for SOFT_DISABLE to syscall events
tracing: Make register/unregister_ftrace_command __init
tracing: Update event filters for multibuffer
recordmcount.pl: Add support for __fentry__
ftrace: Have control op function callback only trace when RCU is watching
rcu: Do not trace rcu_is_watching() functions
ftrace/x86: skip over the breakpoint for ftrace caller
trace/trace_stat: use rbtree postorder iteration helper instead of opencoding
ftrace: Add set_graph_notrace filter
ftrace: Narrow down the protected area of graph_lock
ftrace: Introduce struct ftrace_graph_data
ftrace: Get rid of ftrace_graph_filter_enabled
tracing: Fix potential out-of-bounds in trace_get_user()
tracing: Show more exact help information about snapshot
Mostly bug fixes and clean up. There is a new driver, which is actually
moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree support
in the pwm-backlight driver. Backlights can now additionally be powered
using a regulator and enabled using a GPIO in addition to just the PWM
input.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=CB+z
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Mostly bug fixes and clean up. There is a new driver, which is
actually moving a custom PWM driver from drivers/misc.
The majority of the patches are enhancements to the device tree
support in the pwm-backlight driver. Backlights can now additionally
be powered using a regulator and enabled using a GPIO in addition to
just the PWM input"
* tag 'pwm/for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (30 commits)
Documentation/pwm: Update supported SoC name for pwm-samsung
pwm: samsung: Fix kernel warning while unexporting a channel
MAINTAINERS: Move PWM subsystem tree to kernel.org
Documentation/pwm: Fix trivial typos
pwm-backlight: Remove unused variable
pwm_backlight: avoid short blank screen while doing hibernation
pwm-backlight: Fix brightness adjustment
pwm: add ep93xx PWM support
pwm-backlight: Allow for non-increasing brightness levels
pwm-backlight: Add power supply support
pwm-backlight: Use new enable_gpio field
unicore32: Initialize PWM backlight enable_gpio field
ARM: shmobile: Initialize PWM backlight enable_gpio field
ARM: SAMSUNG: Initialize PWM backlight enable_gpio field
ARM: pxa: Initialize PWM backlight enable_gpio field
ARM: OMAP: Initialize PWM backlight enable_gpio field
pwm-backlight: Add optional enable GPIO
pwm-backlight: Track enable state
pwm-backlight: Refactor backlight power on/off
pwm-backlight: Improve readability
...
Pull nfsd changes from Bruce Fields:
"This includes miscellaneous bugfixes and cleanup and a performance fix
for write-heavy NFSv4 workloads.
(The most significant nfsd-relevant change this time is actually in
the delegation patches that went through Viro, fixing a long-standing
bug that can cause NFSv4 clients to miss updates made by non-nfs users
of the filesystem. Those enable some followup nfsd patches which I
have queued locally, but those can wait till 3.14)"
* 'nfsd-next' of git://linux-nfs.org/~bfields/linux: (24 commits)
nfsd: export proper maximum file size to the client
nfsd4: improve write performance with better sendspace reservations
svcrpc: remove an unnecessary assignment
sunrpc: comment typo fix
Revert "nfsd: remove_stid can be incorporated into nfs4_put_delegation"
nfsd4: fix discarded security labels on setattr
NFSD: Add support for NFS v4.2 operation checking
nfsd4: nfsd_shutdown_net needs state lock
NFSD: Combine decode operations for v4 and v4.1
nfsd: -EINVAL on invalid anonuid/gid instead of silent failure
nfsd: return better errors to exportfs
nfsd: fh_update should error out in unexpected cases
nfsd4: need to destroy revoked delegations in destroy_client
nfsd: no need to unhash_stid before free
nfsd: remove_stid can be incorporated into nfs4_put_delegation
nfsd: nfs4_open_delegation needs to remove_stid rather than unhash_stid
nfsd: nfs4_free_stid
nfsd: fix Kconfig syntax
sunrpc: trim off EC bytes in GSSAPI v2 unwrap
gss_krb5: document that we ignore sequence number
...
Pull dmaengine changes from Dan
1/ Bartlomiej and Dan finalized a rework of the dma address unmap
implementation.
2/ In the course of testing 1/ a collection of enhancements to dmatest
fell out. Notably basic performance statistics, and fixed / enhanced
test control through new module parameters 'run', 'wait', 'noverify',
and 'verbose'. Thanks to Andriy and Linus for their review.
3/ Testing the raid related corner cases of 1/ triggered bugs in the
recently added 16-source operation support in the ioatdma driver.
4/ Some minor fixes / cleanups to mv_xor and ioatdma.
Conflicts:
drivers/dma/dmatest.c
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Rename simple_delete_dentry() to always_delete_dentry() and export it.
Export simple_dentry_operations, while we are at it, and get rid of
their duplicates
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently pskb_trim_rcsum() just balks on CHECKSUM_COMPLETE packets
and remarks them as CHECKSUM_NONE, forcing a software checksum
validation later.
We have all of the mechanics available to fixup the skb->csum value,
even for complicated fragmented packets, via the helpers
skb_checksum() and csum_sub().
So just use them.
Based upon a suggestion by Herbert Xu.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. You will get an new drivers for
Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
bunch of driver fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
Revert "Input: ALPS - add support for model found on Dell XT2"
arm: dts: am335x sk: add touchscreen support
Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
Input: tnetv107x-keypad - make irqs signed for error handling
Input: add driver for Neonode zForce based touchscreens
Input: sh_keysc - enable the driver on all ARM platforms
Input: remove a redundant max() call
Input: mousedev - allow disabling even without CONFIG_EXPERT
Input: allow deselecting serio drivers even without CONFIG_EXPERT
Input: i8042 - add PNP modaliases
Input: evdev - fall back to vmalloc for client event buffer
Input: cypress_ps2 - do not consider data bad if palm is detected
Input: cypress_ps2 - remove useless cast
Input: fix PWM-related undefined reference errors
Input: ALPS - change secondary device's name
Input: wacom - not all multi-interface devices support touch
Input: nspire-keypad - add missing clk_disable_unprepare() on error path
...
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver.
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid build
breakage in the future.
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver.
- A small arizona update for new wm5110 DSP registers and a few fixes.
- A small palmas update as well, including an of_device table addition
and a few minor fixes.
- Two small mfd-core changes, one including a memory leak fix for when
mfd_add_device() fails.
- Our usual round of minor cleanups and janitorial fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=nQ/p
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD updates from Samuel Ortiz:
"For the 3.13 merge window we have a couple of new drivers for the AMS
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid
build breakage in the future
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver
- A small arizona update for new wm5110 DSP registers and a few fixes
- A small palmas update as well, including an of_device table
addition and a few minor fixes
- Two small mfd-core changes, one including a memory leak fix for
when mfd_add_device() fails
- Our usual round of minor cleanups and janitorial fixes"
* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
Documentation: mfd: Update s2mps11.txt
mfd: pm8921: Potential NULL dereference in pm8921_remove()
mfd: Fix memory leak in mfd_add_devices()
mfd: Stop setting refcounting pointers in original mfd_cell arrays
mfd: wm5110: Enable micd clamp functionality
mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
mfd: max77693: Fix up bug of wrong interrupt number
mfd: as3722: Don't export the regmap config
mfd: twl6040: Remove obsolete cleanup for i2c clientdata
mfd: tps65910: Remove warning during dt node parsing
mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
mfd: Add support for ams AS3722 PMIC
mfd: max77693: Include linux/of.h header
mfd: tc3589x: Detect the precise version
mfd: omap-usb: prepare/unprepare clock while enable/disable
mfd: max77686: Include linux/of.h header
mfd: max8907: Include linux/of.h header
mfd: max8997: Include linux/of.h header
...
Introduce helper function macvlan_dev_real_dev which returns the
underlying device of a macvlan device, similar to vlan_dev_real_dev()
for 802.1q VLAN devices.
v2: IFF_MACVLAN flag and equivalent of is_macvlan_dev() were
introduced in the meantime
v3: do BUG() if compiled without macvlan support
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull drm updates from Dave Airlie:
"This is a combo of -next and some -fixes that came in in the
intervening time.
Highlights:
New drivers:
ARM Armada driver for Marvell Armada 510 SOCs
Intel:
Broadwell initial support under a default off switch,
Stereo/3D HDMI mode support
Valleyview improvements
Displayport improvements
Haswell fixes
initial mipi dsi panel support
CRC support for debugging
build with CONFIG_FB=n
Radeon:
enable DPM on a number of GPUs by default
secondary GPU powerdown support
enable HDMI audio by default
Hawaii support
Nouveau:
dynamic pm code infrastructure reworked, does nothing major yet
GK208 modesetting support
MSI fixes, on by default again
PMPEG improvements
pageflipping fixes
GMA500:
minnowboard SDVO support
VMware:
misc fixes
MSM:
prime, plane and rendernodes support
Tegra:
rearchitected to put the drm driver into the drm subsystem.
HDMI and gr2d support for tegra 114 SoC
QXL:
oops fix, and multi-head fixes
DRM core:
sysfs lifetime fixes
client capability ioctl
further cleanups to device midlayer
more vblank timestamp fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (789 commits)
drm/nouveau: do not map evicted vram buffers in nouveau_bo_vma_add
drm/nvc0-/gr: shift wrapping bug in nvc0_grctx_generate_r406800
drm/nouveau/pwr: fix missing mutex unlock in a failure path
drm/nv40/therm: fix slowing down fan when pstate undefined
drm/nv11-: synchronise flips to vblank, unless async flip requested
drm/nvc0-: remove nasty fifo swmthd hack for flip completion method
drm/nv10-: we no longer need to create nvsw object on user channels
drm/nouveau: always queue flips relative to kernel channel activity
drm/nouveau: there is no need to reserve/fence the new fb when flipping
drm/nouveau: when bailing out of a pushbuf ioctl, do not remove previous fence
drm/nouveau: allow nouveau_fence_ref() to be a noop
drm/nvc8/mc: msi rearm is via the nvc0 method
drm/ttm: Fix vma page_prot bit manipulation
drm/vmwgfx: Fix a couple of compile / sparse warnings and errors
drm/vmwgfx: Resource evict fixes
drm/edid: compare actual vrefresh for all modes for quirks
drm: shmob_drm: Convert to clk_prepare/unprepare
drm/nouveau: fix 32-bit build
drm/i915/opregion: fix build error on CONFIG_ACPI=n
Revert "drm/radeon/audio: don't set speaker allocation on DCE4+"
...
This time the updates contain:
* Tracepoints for certain IOMMU-API functions to make
their use easier to debug
* A tracepoint for IOMMU page faults to make it easier
to get them in user space
* Updates and fixes for the new ARM SMMU driver after
the first hardware showed up
* Various other fixes and cleanups in other IOMMU drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IWTK
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time the updates contain:
- Tracepoints for certain IOMMU-API functions to make their use
easier to debug
- A tracepoint for IOMMU page faults to make it easier to get them in
user space
- Updates and fixes for the new ARM SMMU driver after the first
hardware showed up
- Various other fixes and cleanups in other IOMMU drivers"
* tag 'iommu-updates-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (26 commits)
iommu/shmobile: Enable the driver on all ARM platforms
iommu/tegra-smmu: Staticize tegra_smmu_pm_ops
iommu/tegra-gart: Staticize tegra_gart_pm_ops
iommu/vt-d: Use list_for_each_entry_safe() for dmar_domain->devices traversal
iommu/vt-d: Use for_each_drhd_unit() instead of list_for_each_entry()
iommu/vt-d: Fixed interaction of VFIO_IOMMU_MAP_DMA with IOMMU address limits
iommu/arm-smmu: Clear global and context bank fault status registers
iommu/arm-smmu: Print context fault information
iommu/arm-smmu: Check for num_context_irqs > 0 to avoid divide by zero exception
iommu/arm-smmu: Refine check for proper size of mapped region
iommu/arm-smmu: Switch to subsys_initcall for driver registration
iommu/arm-smmu: use relaxed accessors where possible
iommu/arm-smmu: replace devm_request_and_ioremap by devm_ioremap_resource
iommu: Remove stack trace from broken irq remapping warning
iommu: Change iommu driver to call io_page_fault trace event
iommu: Add iommu_error class event to iommu trace
iommu/tegra: gart: cleanup devm_* functions usage
iommu/tegra: Print phys_addr_t using %pa
iommu: No need to pass '0x' when '%pa' is used
iommu: Change iommu driver to call unmap trace event
...
side: the HV and emulation flavors can now coexist in a single kernel
is probably the most interesting change from a user point of view.
On the x86 side there are nested virtualization improvements and a
few bugfixes. ARM got transparent huge page support, improved
overcommit, and support for big endian guests.
Finally, there is a new interface to connect KVM with VFIO. This
helps with devices that use NoSnoop PCI transactions, letting the
driver in the guest execute WBINVD instructions. This includes
some nVidia cards on Windows, that fail to start without these
patches and the corresponding userspace changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJShPAhAAoJEBvWZb6bTYbyl48P/297GgmELHAGBgjvb6q7yyGu
L8+eHjKbh4XBAkPwyzbvUjuww5z2hM0N3JQ0BDV9oeXlO+zwwCEns/sg2Q5/NJXq
XxnTeShaKnp9lqVBnE6G9rAOUWKoyLJ2wItlvUL8JlaO9xJ0Vmk0ta4n2Nv5GqDp
db6UD7vju6rHtIAhNpvvAO51kAOwc01xxRixCVb7KUYOnmO9nvpixzoI/S0Rp1gu
w/OWMfCosDzBoT+cOe79Yx1OKcpaVW94X6CH1s+ShCw3wcbCL2f13Ka8/E3FIcuq
vkZaLBxio7vjUAHRjPObw0XBW4InXEbhI1DjzIvm8dmc4VsgmtLQkTCG8fj+jINc
dlHQUq6Do+1F4zy6WMBUj8tNeP1Z9DsABp98rQwR8+BwHoQpGQBpAxW0TE0ZMngC
t1caqyvjZ5pPpFUxSrAV+8Kg4AvobXPYOim0vqV7Qea07KhFcBXLCfF7BWdwq/Jc
0CAOlsLL4mHGIQWZJuVGw0YGP7oATDCyewlBuDObx+szYCoV4fQGZVBEL0KwJx/1
7lrLN7JWzRyw6xTgJ5VVwgYE1tUY4IFQcHu7/5N+dw8/xg9KWA3f4PeMavIKSf+R
qteewbtmQsxUnvuQIBHLs8NRWPnBPy+F3Sc2ckeOLIe4pmfTte6shtTXcLDL+LqH
NTmT/cfmYp2BRkiCfCiS
=rWNf
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM changes from Paolo Bonzini:
"Here are the 3.13 KVM changes. There was a lot of work on the PPC
side: the HV and emulation flavors can now coexist in a single kernel
is probably the most interesting change from a user point of view.
On the x86 side there are nested virtualization improvements and a few
bugfixes.
ARM got transparent huge page support, improved overcommit, and
support for big endian guests.
Finally, there is a new interface to connect KVM with VFIO. This
helps with devices that use NoSnoop PCI transactions, letting the
driver in the guest execute WBINVD instructions. This includes some
nVidia cards on Windows, that fail to start without these patches and
the corresponding userspace changes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (146 commits)
kvm, vmx: Fix lazy FPU on nested guest
arm/arm64: KVM: PSCI: propagate caller endianness to the incoming vcpu
arm/arm64: KVM: MMIO support for BE guest
kvm, cpuid: Fix sparse warning
kvm: Delete prototype for non-existent function kvm_check_iopl
kvm: Delete prototype for non-existent function complete_pio
hung_task: add method to reset detector
pvclock: detect watchdog reset at pvclock read
kvm: optimize out smp_mb after srcu_read_unlock
srcu: API for barrier after srcu read unlock
KVM: remove vm mmap method
KVM: IOMMU: hva align mapping page size
KVM: x86: trace cpuid emulation when called from emulator
KVM: emulator: cleanup decode_register_operand() a bit
KVM: emulator: check rex prefix inside decode_register()
KVM: x86: fix emulation of "movzbl %bpl, %eax"
kvm_host: typo fix
KVM: x86: emulate SAHF instruction
MAINTAINERS: add tree for kvm.git
Documentation/kvm: add a 00-INDEX file
...
some robustness fixes for broken virtio devices, plus minor tweaks.
[vs last pull request: added the virtio-scsi broken vq escape patch, which
I somehow lost.]
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=vY2L
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"Nothing really exciting: some groundwork for changing virtio endian,
and some robustness fixes for broken virtio devices, plus minor
tweaks"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_scsi: verify if queue is broken after virtqueue_get_buf()
x86, asmlinkage, lguest: Pass in globals into assembler statement
virtio: mmio: fix signature checking for BE guests
virtio_ring: adapt to notify() returning bool
virtio_net: verify if queue is broken after virtqueue_get_buf()
virtio_console: verify if queue is broken after virtqueue_get_buf()
virtio_blk: verify if queue is broken after virtqueue_get_buf()
virtio_ring: add new function virtqueue_is_broken()
virtio_test: verify if virtqueue_kick() succeeded
virtio_net: verify if virtqueue_kick() succeeded
virtio_ring: let virtqueue_{kick()/notify()} return a bool
virtio_ring: change host notification API
virtio_config: remove virtio_config_val
virtio: use size-based config accessors.
virtio_config: introduce size-based accessors.
virtio_ring: plug kmemleak false positive.
virtio: pm: use CONFIG_PM_SLEEP instead of CONFIG_PM
Fix following errors:
include/linux/cmdline-parser.h:17:12: error: 'BDEVNAME_SIZE' undeclared here
block/cmdline-parser.c:17:2: error: implicit declaration of function 'kzalloc'
Signed-off-by: Alexander Beregalov <alexander.beregalov@intel.com>
Cc: CaiZhiyong <caizhiyong@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch enhances the type safety for the kfifo API. It is now safe
to put const data into a non const FIFO and the API will now generate a
compiler warning when reading from the fifo where the destination
address is pointing to a const variable.
As a side effect the kfifo_put() does now expect the value of an element
instead a pointer to the element. This was suggested Russell King. It
make the handling of the kfifo_put easier since there is no need to
create a helper variable for getting the address of a pointer or to pass
integers of different sizes.
IMHO the API break is okay, since there are currently only six users of
kfifo_put().
The code is also cleaner by kicking out the "if (0)" expressions.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make this useful helper available for other users.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
x86_64 allnoconfig:
kernel/up.c:25: error: redefinition of '__smp_call_function_single'
include/linux/smp.h:154: note: previous definition of '__smp_call_function_single' was here
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We've switched over every architecture that supports SMP to it, so
remove the new useless config variable.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit was incomplete in that code to remove items from the per-cpu
lists was missing and never acquired a user in the 5 years it has been in
the tree. We're going to implement what it seems to try to archive in a
simpler way, and this code is in the way of doing so.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All users are converted over to reinit_completion(). Remove the old
macro now.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For the casual device driver writer, it is hard to remember when to use
init_completion (to init a completion structure) or INIT_COMPLETION (to
*reinit* a completion structure). Furthermore, while all other
completion functions exepct a pointer as a parameter, INIT_COMPLETION
does not. To make it easier to remember which function to use and to
make code more readable, introduce a new inline function with the proper
name and consistent argument type. Update the kernel-doc for
init_completion while we are here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are several users who want to know bytes written by seq_*() for
alignment purpose. Currently they are using %n format for knowing it
because seq_*() returns 0 on success.
This patch introduces seq_setwidth() and seq_pad() for allowing them to
align without using %n format.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Joe Perches <joe@perches.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid the fragile Kconfig construct guestimating spinlock_t sizes; use a
friendly compile-time test to determine this.
[kirill.shutemov@linux.intel.com: drop CONFIG_CMPXCHG_LOCKREF]
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If DEBUG_SPINLOCK and DEBUG_LOCK_ALLOC are enabled spinlock_t on x86_64
is 72 bytes. For page->ptl they will be allocated from kmalloc-96 slab,
so we loose 24 on each. An average system can easily allocate few tens
thousands of page->ptl and overhead is significant.
Let's create a separate slab for page->ptl allocation to solve this.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kernel/bounds.c to convert build-time spinlock_t size check into a
preprocessor symbol and apply that to properly separate the page::ptl
situation.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If split page table lock is in use, we embed the lock into struct page
of table's page. We have to disable split lock, if spinlock_t is too
big be to be embedded, like when DEBUG_SPINLOCK or DEBUG_LOCK_ALLOC
enabled.
This patch add support for dynamic allocation of split page table lock
if we can't embed it to struct page.
page->ptl is unsigned long now and we use it as spinlock_t if
sizeof(spinlock_t) <= sizeof(long), otherwise it's pointer to spinlock_t.
The spinlock_t allocated in pgtable_page_ctor() for PTE table and in
pgtable_pmd_page_ctor() for PMD table. All other helpers converted to
support dynamically allocated page->ptl.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change pgtable_page_ctor() return type from void to bool. Returns true,
if initialization is successful and false otherwise.
Current implementation never fails, but it will change later.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The basic idea is the same as with PTE level: the lock is embedded into
struct page of table's page.
We can't use mm->pmd_huge_pte to store pgtables for THP, since we don't
take mm->page_table_lock anymore. Let's reuse page->lru of table's page
for that.
pgtable_pmd_page_ctor() returns true, if initialization is successful
and false otherwise. Current implementation never fails, but assumption
that constructor can fail will help to port it to -rt where spinlock_t
is rather huge and cannot be embedded into struct page -- dynamic
allocation is required.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Alex Thorlton <athorlton@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hugh Dickins <hughd@google.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently mm->pmd_huge_pte protected by page table lock. It will not
work with split lock. We have to have per-pmd pmd_huge_pte for proper
access serialization.
For now, let's just introduce wrapper to access mm->pmd_huge_pte.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Alex Thorlton <athorlton@sgi.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With split ptlock it's important to know which lock
pmd_trans_huge_lock() took. This patch adds one more parameter to the
function to return the lock.
In most places migration to new api is trivial. Exception is
move_huge_pmd(): we need to take two locks if pmd tables are different.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Alex Thorlton <athorlton@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Sedat Dilek <sedat.dilek@gmail.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct acpi_device fields are only available when CONFIG_ACPI is set. We may
find use for dev_name(&adev->dev) in generic code that is build also without
CONFIG_ACPI is set but currently this requires #ifdef CONFIG_ACPI churn.
Provide here an accessor that returns dev_name of embedded struct device dev
in struct acpi_device or NULL depending on CONFIG_ACPI setting.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since DEVICE_ACPI_HANDLE() is now literally identical to
ACPI_HANDLE(), replace it with the latter everywhere and drop its
definition from include/acpi.h.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify struct acpi_dev_node to contain a pointer to struct acpi_device
associated with the given device object (that is, its ACPI companion
device) instead of an ACPI handle corresponding to it. Introduce two
new macros for manipulating that pointer in a CONFIG_ACPI-safe way,
ACPI_COMPANION() and ACPI_COMPANION_SET(), and rework the
ACPI_HANDLE() macro to take the above changes into account.
Drop the ACPI_HANDLE_SET() macro entirely and rework its users to
use ACPI_COMPANION_SET() instead. For some of them who used to
pass the result of acpi_get_child() directly to ACPI_HANDLE_SET()
introduce a helper routine acpi_preset_companion() doing an
equivalent thing.
The main motivation for doing this is that there are things
represented by struct acpi_device objects that don't have valid
ACPI handles (so called fixed ACPI hardware features, such as
power and sleep buttons) and we would like to create platform
device objects for them and "glue" them to their ACPI companions
in the usual way (which currently is impossible due to the
lack of valid ACPI handles). However, there are more reasons
why it may be useful.
First, struct acpi_device pointers allow of much better type checking
than void pointers which are ACPI handles, so it should be more
difficult to write buggy code using modified struct acpi_dev_node
and the new macros. Second, the change should help to reduce (over
time) the number of places in which the result of ACPI_HANDLE() is
passed to acpi_bus_get_device() in order to obtain a pointer to the
struct acpi_device associated with the given "physical" device,
because now that pointer is returned by ACPI_COMPANION() directly.
Finally, the change should make it easier to write generic code that
will build both for CONFIG_ACPI set and unset without adding explicit
compiler directives to it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> # on Haswell
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com> # for ATA and SDIO part
Fix whitespace, capitalization, and spelling errors. No functional change.
I know "busses" is not an error, but "buses" was more common, so I used it
consistently.
Signed-off-by: Marta Rybczynska <rybczynska@gmail.com> (pci_reset_bridge_secondary_bus())
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull core locking changes from Ingo Molnar:
"The biggest changes:
- add lockdep support for seqcount/seqlocks structures, this
unearthed both bugs and required extra annotation.
- move the various kernel locking primitives to the new
kernel/locking/ directory"
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (21 commits)
block: Use u64_stats_init() to initialize seqcounts
locking/lockdep: Mark __lockdep_count_forward_deps() as static
lockdep/proc: Fix lock-time avg computation
locking/doc: Update references to kernel/mutex.c
ipv6: Fix possible ipv6 seqlock deadlock
cpuset: Fix potential deadlock w/ set_mems_allowed
seqcount: Add lockdep functionality to seqcount/seqlock structures
net: Explicitly initialize u64_stats_sync structures for lockdep
locking: Move the percpu-rwsem code to kernel/locking/
locking: Move the lglocks code to kernel/locking/
locking: Move the rwsem code to kernel/locking/
locking: Move the rtmutex code to kernel/locking/
locking: Move the semaphore core to kernel/locking/
locking: Move the spinlock code to kernel/locking/
locking: Move the lockdep code to kernel/locking/
locking: Move the mutex code to kernel/locking/
hung_task debugging: Add tracepoint to report the hang
x86/locking/kconfig: Update paravirt spinlock Kconfig description
lockstat: Report avg wait and hold times
lockdep, x86/alternatives: Drop ancient lockdep fixup message
...
Nothing particularly stands out in this pull request. The biggest part of the
changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix potential
dead lock" which hopefully fixes the fb locking issues reported by multiple
persons.
There are also a few commits that have changes to arch/arm/mach-at91 and
arch/avr32, which have been acked by the maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=59+j
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Nothing particularly stands out in this pull request. The biggest
part of the changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix
potential dead lock" which hopefully fixes the fb locking issues
reported by multiple persons.
There are also a few commits that have changes to arch/arm/mach-at91
and arch/avr32, which have been acked by the maintainers"
* tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (143 commits)
fb: reorder the lock sequence to fix potential dead lock
fbdev: shmobile-lcdcfb: Convert to clk_prepare/unprepare
fbdev: shmobile-hdmi: Convert to clk_prepare/unprepare
omapdss: Add new panel driver for Topolly td028ttec1 LCD.
video: exynos_mipi_dsi: Unlock the mutex before returning
video: da8xx-fb: remove unwanted define
video: Remove unnecessary semicolons
simplefb: use write-combined remapping
simplefb: fix unmapping fb during destruction
OMAPDSS: connector-dvi: fix releasing i2c_adapter
OMAPDSS: DSI: fix perf measuring ifdefs
framebuffer: Use fb_<level>
framebuffer: Add fb_<level> convenience logging macros
efifb: prevent null-deref when iterating dmi_list
fbdev: fix error return code in metronomefb_probe()
video: xilinxfb: Fix for "Use standard variable name convention"
OMAPDSS: Fix de_level in videomode_to_omap_video_timings()
video: xilinxfb: Simplify error path
video: xilinxfb: Use devm_kzalloc instead of kzalloc
video: xilinxfb: Use standard variable name convention
...
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
Add a new API wait_event_cmd(). It's a variant of wait_even() with two
commands executed. One is executed before sleep, another after sleep.
Modified to match use wait.h approach based on suggestion by
Peter Zijlstra <peterz@infradead.org> - neilb
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
* Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
* Other general cleanups (removing unused functions, options, variables,
fields; use correct interfaces)
* Fix BUG() for new odd-sized NAND, which report non-power-of-2 dimensions via
ONFI
* Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
* Improve differentiation between SLC and MLC NAND -- this clarifies an ABI
issue regarding the MTD "type" (in sysfs and in ioctl(MEMGETINFO)), where
the MTD_MLCNANDFLASH type was present but inconsistently used
* Extend GPMI NAND to support multi-chip-select NAND for some platforms
* Many improvements to the OMAP2/3 NAND driver, including an expanded DT
binding to bring us closer to mainline support for some OMAP systems
* Fix a deadlock in the error path of the Atmel NAND driver probe
* Correct the error codes from MTD mmap() to conform to POSIX and the Linux
Programmer's Manual. This is an acknowledged change in the MTD ABI, but I
can't imagine somebody relying on the non-standard -ENOSYS error code
specifically. Am I just being unimaginative? :)
* Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
* More? Read the log!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=z5qO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
Pull block IO core updates from Jens Axboe:
"This is the pull request for the core changes in the block layer for
3.13. It contains:
- The new blk-mq request interface.
This is a new and more scalable queueing model that marries the
best part of the request based interface we currently have (which
is fully featured, but scales poorly) and the bio based "interface"
which the new drivers for high IOPS devices end up using because
it's much faster than the request based one.
The bio interface has no block layer support, since it taps into
the stack much earlier. This means that drivers end up having to
implement a lot of functionality on their own, like tagging,
timeout handling, requeue, etc. The blk-mq interface provides all
these. Some drivers even provide a switch to select bio or rq and
has code to handle both, since things like merging only works in
the rq model and hence is faster for some workloads. This is a
huge mess. Conversion of these drivers nets us a substantial code
reduction. Initial results on converting SCSI to this model even
shows an 8x improvement on single queue devices. So while the
model was intended to work on the newer multiqueue devices, it has
substantial improvements for "classic" hardware as well. This code
has gone through extensive testing and development, it's now ready
to go. A pull request is coming to convert virtio-blk to this
model will be will be coming as well, with more drivers scheduled
for 3.14 conversion.
- Two blktrace fixes from Jan and Chen Gang.
- A plug merge fix from Alireza Haghdoost.
- Conversion of __get_cpu_var() from Christoph Lameter.
- Fix for sector_div() with 64-bit divider from Geert Uytterhoeven.
- A fix for a race between request completion and the timeout
handling from Jeff Moyer. This is what caused the merge conflict
with blk-mq/core, in case you are looking at that.
- A dm stacking fix from Mike Snitzer.
- A code consolidation fix and duplicated code removal from Kent
Overstreet.
- A handful of block bug fixes from Mikulas Patocka, fixing a loop
crash and memory corruption on blk cg.
- Elevator switch bug fix from Tomoki Sekiyama.
A heads-up that I had to rebase this branch. Initially the immutable
bio_vecs had been queued up for inclusion, but a week later, it became
clear that it wasn't fully cooked yet. So the decision was made to
pull this out and postpone it until 3.14. It was a straight forward
rebase, just pruning out the immutable series and the later fixes of
problems with it. The rest of the patches applied directly and no
further changes were made"
* 'for-3.13/core' of git://git.kernel.dk/linux-block: (31 commits)
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
block: Do not call sector_div() with a 64-bit divisor
kernel: trace: blktrace: remove redundent memcpy() in compat_blk_trace_setup()
block: Consolidate duplicated bio_trim() implementations
block: Use rw_copy_check_uvector()
block: Enable sysfs nomerge control for I/O requests in the plug list
block: properly stack underlying max_segment_size to DM device
elevator: acquire q->sysfs_lock in elevator_change()
elevator: Fix a race in elevator switching and md device initialization
block: Replace __get_cpu_var uses
bdi: test bdi_init failure
block: fix a probe argument to blk_register_region
loop: fix crash if blk_alloc_queue fails
blk-core: Fix memory corruption if blkcg_init_queue fails
block: fix race between request completion and timeout handling
blktrace: Send BLK_TN_PROCESS events to all running traces
blk-mq: don't disallow request merges for req->special being set
blk-mq: mq plug list breakage
blk-mq: fix for flush deadlock
...
Hang a common 'unmap' object off of dma descriptors for the purpose of
providing a unified unmapping interface. The lifetime of a mapping may
span multiple descriptors, so these unmap objects are reference counted
by related descriptor.
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
[bzolnier: fix IS_ENABLED() check]
[bzolnier: fix release ordering in dmaengine_destroy_unmap_pool()]
[bzolnier: fix check for success in dmaengine_init_unmap_pool()]
[bzolnier: use mempool_free() instead of kmem_cache_free()]
[bzolnier: add missing unmap->len initializations]
[bzolnier: add __init tag to dmaengine_init_unmap_pool()]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[djbw: move DMAENGINE=n support to this patch for async_tx]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Add a hook for a common dma unmap implementation to enable removal of
the per driver custom unmap code. (A reworked version of Bartlomiej
Zolnierkiewicz's patches to remove the custom callbacks and the size
increase of dma_async_tx_descriptor for drivers that don't care about
raid).
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: Dave Jiang <dave.jiang@intel.com>
[bzolnier: prepare pl330 driver for adding missing unmap while at it]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull ARM updates from Russell King:
"Included in this series are:
1. BE8 (modern big endian) changes for ARM from Ben Dooks
2. big.Little support from Nicolas Pitre and Dave Martin
3. support for LPAE systems with all system memory above 4GB
4. Perf updates from Will Deacon
5. Additional prefetching and other performance improvements from Will.
6. Neon-optimised AES implementation fro Ard.
7. A number of smaller fixes scattered around the place.
There is a rather horrid merge conflict in tools/perf - I was never
notified of the conflict because it originally occurred between Will's
tree and other stuff. Consequently I have a resolution which Will
forwarded me, which I'll forward on immediately after sending this
mail.
The other notable thing is I'm expecting some build breakage in the
crypto stuff on ARM only with Ard's AES patches. These were merged
into a stable git branch which others had already pulled, so there's
little I can do about this. The problem is caused because these
patches have a dependency on some code in the crypto git tree - I
tried requesting a branch I can pull to resolve these, and all I got
each time from the crypto people was "we'll revert our patches then"
which would only make things worse since I still don't have the
dependent patches. I've no idea what's going on there or how to
resolve that, and since I can't split these patches from the rest of
this pull request, I'm rather stuck with pushing this as-is or
reverting Ard's patches.
Since it should "come out in the wash" I've left them in - the only
build problems they seem to cause at the moment are with randconfigs,
and since it's a new feature anyway. However, if by -rc1 the
dependencies aren't in, I think it'd be best to revert Ard's patches"
I resolved the perf conflict roughly as per the patch sent by Russell,
but there may be some differences. Any errors are likely mine. Let's
see how the crypto issues work out..
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (110 commits)
ARM: 7868/1: arm/arm64: remove atomic_clear_mask() in "include/asm/atomic.h"
ARM: 7867/1: include: asm: use 'int' instead of 'unsigned long' for 'oldval' in atomic_cmpxchg().
ARM: 7866/1: include: asm: use 'long long' instead of 'u64' within atomic.h
ARM: 7871/1: amba: Extend number of IRQS
ARM: 7887/1: Don't smp_cross_call() on UP devices in arch_irq_work_raise()
ARM: 7872/1: Support arch_irq_work_raise() via self IPIs
ARM: 7880/1: Clear the IT state independent of the Thumb-2 mode
ARM: 7878/1: nommu: Implement dummy early_paging_init()
ARM: 7876/1: clear Thumb-2 IT state on exception handling
ARM: 7874/2: bL_switcher: Remove cpu_hotplug_driver_{lock,unlock}()
ARM: footbridge: fix build warnings for netwinder
ARM: 7873/1: vfp: clear vfp_current_hw_state for dying cpu
ARM: fix misplaced arch_virt_to_idmap()
ARM: 7848/1: mcpm: Implement cpu_kill() to synchronise on powerdown
ARM: 7847/1: mcpm: Factor out logical-to-physical CPU translation
ARM: 7869/1: remove unused XSCALE_PMU Kconfig param
ARM: 7864/1: Handle 64-bit memory in case of 32-bit phys_addr_t
ARM: 7863/1: Let arm_add_memory() always use 64-bit arguments
ARM: 7862/1: pcpu: replace __get_cpu_var_uses
ARM: 7861/1: cacheflush: consolidate single-CPU ARMv7 cache disabling code
...
Pull DMA mask updates from Russell King:
"This series cleans up the handling of DMA masks in a lot of drivers,
fixing some bugs as we go.
Some of the more serious errors include:
- drivers which only set their coherent DMA mask if the attempt to
set the streaming mask fails.
- drivers which test for a NULL dma mask pointer, and then set the
dma mask pointer to a location in their module .data section -
which will cause problems if the module is reloaded.
To counter these, I have introduced two helper functions:
- dma_set_mask_and_coherent() takes care of setting both the
streaming and coherent masks at the same time, with the correct
error handling as specified by the API.
- dma_coerce_mask_and_coherent() which resolves the problem of
drivers forcefully setting DMA masks. This is more a marker for
future work to further clean these locations up - the code which
creates the devices really should be initialising these, but to fix
that in one go along with this change could potentially be very
disruptive.
The last thing this series does is prise away some of Linux's addition
to "DMA addresses are physical addresses and RAM always starts at
zero". We have ARM LPAE systems where all system memory is above 4GB
physical, hence having DMA masks interpreted by (eg) the block layers
as describing physical addresses in the range 0..DMAMASK fails on
these platforms. Santosh Shilimkar addresses this in this series; the
patches were copied to the appropriate people multiple times but were
ignored.
Fixing this also gets rid of some ARM weirdness in the setup of the
max*pfn variables, and brings ARM into line with every other Linux
architecture as far as those go"
* 'for-linus-dma-masks' of git://git.linaro.org/people/rmk/linux-arm: (52 commits)
ARM: 7805/1: mm: change max*pfn to include the physical offset of memory
ARM: 7797/1: mmc: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7796/1: scsi: Use dma_max_pfn(dev) helper for bounce_limit calculations
ARM: 7795/1: mm: dma-mapping: Add dma_max_pfn(dev) helper function
ARM: 7794/1: block: Rename parameter dma_mask to max_addr for blk_queue_bounce_limit()
ARM: DMA-API: better handing of DMA masks for coherent allocations
ARM: 7857/1: dma: imx-sdma: setup dma mask
DMA-API: firmware/google/gsmi.c: avoid direct access to DMA masks
DMA-API: dcdbas: update DMA mask handing
DMA-API: dma: edma.c: no need to explicitly initialize DMA masks
DMA-API: usb: musb: use platform_device_register_full() to avoid directly messing with dma masks
DMA-API: crypto: remove last references to 'static struct device *dev'
DMA-API: crypto: fix ixp4xx crypto platform device support
DMA-API: others: use dma_set_coherent_mask()
DMA-API: staging: use dma_set_coherent_mask()
DMA-API: usb: use new dma_coerce_mask_and_coherent()
DMA-API: usb: use dma_set_coherent_mask()
DMA-API: parport: parport_pc.c: use dma_coerce_mask_and_coherent()
DMA-API: net: octeon: use dma_coerce_mask_and_coherent()
DMA-API: net: nxp/lpc_eth: use dma_coerce_mask_and_coherent()
...
On a 68k platform a couple of interrupts are demultiplexed and
"polled" from a top level interrupt. Unfortunately there is no way to
determine which of the sub interrupts raised the top level interrupt,
so all of the demultiplexed interrupt handlers need to be
invoked. Given a high enough frequency this can trigger the spurious
interrupt detection mechanism, if one of the demultiplex interrupts
returns IRQ_NONE continuously. But this is a false positive as the
polling causes this behaviour and not buggy hardware/software.
Introduce IRQ_POLLED which can be set at interrupt chip setup time via
irq_set_status_flags(). The flag excludes the interrupt from the
spurious detector and from all core polling activities.
Reported-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@vger.kernel.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.02.1311061149250.23353@ionos.tec.linutronix.de
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
Merge first patch-bomb from Andrew Morton:
"Quite a lot of other stuff is banked up awaiting further
next->mainline merging, but this batch contains:
- Lots of random misc patches
- OCFS2
- Most of MM
- backlight updates
- lib/ updates
- printk updates
- checkpatch updates
- epoll tweaking
- rtc updates
- hfs
- hfsplus
- documentation
- procfs
- update gcov to gcc-4.7 format
- IPC"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (269 commits)
ipc, msg: fix message length check for negative values
ipc/util.c: remove unnecessary work pending test
devpts: plug the memory leak in kill_sb
./Makefile: export initial ramdisk compression config option
init/Kconfig: add option to disable kernel compression
drivers: w1: make w1_slave::flags long to avoid memory corruption
drivers/w1/masters/ds1wm.cuse dev_get_platdata()
drivers/memstick/core/ms_block.c: fix unreachable state in h_msb_read_page()
drivers/memstick/core/mspro_block.c: fix attributes array allocation
drivers/pps/clients/pps-gpio.c: remove redundant of_match_ptr
kernel/panic.c: reduce 1 byte usage for print tainted buffer
gcov: reuse kbasename helper
kernel/gcov/fs.c: use pr_warn()
kernel/module.c: use pr_foo()
gcov: compile specific gcov implementation based on gcc version
gcov: add support for gcc 4.7 gcov format
gcov: move gcov structs definitions to a gcc version specific file
kernel/taskstats.c: return -ENOMEM when alloc memory fails in add_del_listener()
kernel/taskstats.c: add nla_nest_cancel() for failure processing between nla_nest_start() and nla_nest_end()
kernel/sysctl_binary.c: use scnprintf() instead of snprintf()
...
Pull vfs updates from Al Viro:
"All kinds of stuff this time around; some more notable parts:
- RCU'd vfsmounts handling
- new primitives for coredump handling
- files_lock is gone
- Bruce's delegations handling series
- exportfs fixes
plus misc stuff all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (101 commits)
ecryptfs: ->f_op is never NULL
locks: break delegations on any attribute modification
locks: break delegations on link
locks: break delegations on rename
locks: helper functions for delegation breaking
locks: break delegations on unlink
namei: minor vfs_unlink cleanup
locks: implement delegations
locks: introduce new FL_DELEG lock flag
vfs: take i_mutex on renamed file
vfs: rename I_MUTEX_QUOTA now that it's not used for quotas
vfs: don't use PARENT/CHILD lock classes for non-directories
vfs: pull ext4's double-i_mutex-locking into common code
exportfs: fix quadratic behavior in filehandle lookup
exportfs: better variable name
exportfs: move most of reconnect_path to helper function
exportfs: eliminate unused "noprogress" counter
exportfs: stop retrying once we race with rename/remove
exportfs: clear DISCONNECTED on all parents sooner
exportfs: more detailed comment for path_reconnect
...
Pull fuse updates from Miklos Szeredi:
"This adds a ->writepage() implementation to fuse, improving mmaped
writeout and paving the way for buffered writeback.
And there's a patch to add a fix minor number for /dev/cuse, similarly
to /dev/fuse"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: writepages: protect secondary requests from fuse file release
fuse: writepages: update bdi writeout when deleting secondary request
fuse: writepages: crop secondary requests
fuse: writepages: roll back changes if request not found
cuse: add fix minor number to /dev/cuse
fuse: writepage: skip already in flight
fuse: writepages: handle same page rewrites
fuse: writepages: fix aggregation
fuse: fix race in fuse_writepages()
fuse: Implement writepages callback
fuse: don't BUG on no write file
fuse: lock page in mkwrite
fuse: Prepare to handle multiple pages in writeback
fuse: Getting file for writeback helper
Pull cgroup changes from Tejun Heo:
"Not too much activity this time around. css_id is finally killed and
a minor update to device_cgroup"
* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
device_cgroup: remove can_attach
cgroup: kill css_id
memcg: stop using css id
memcg: fail to create cgroup if the cgroup id is too big
memcg: convert to use cgroup id
memcg: convert to use cgroup_is_descendant()
Pull libata changes from Tejun Heo:
"Nothing too interesting. Only two minor fixes in libata core. Most
changes are specific to hardware which isn't too common"
* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device IDs for Intel Wildcat Point-LP
sata_rcar: Convert to clk_prepare/unprepare
drivers/libata: Set max sector to 65535 for Slimtype DVD A DS8A9SH drive
libata: Add some missing command descriptions
sata_highbank: clear whole array in highbank_initialize_phys()
ahci: disabled FBS prior to issuing software reset
libata: Fix display of sata speed
ahci: imx: setup power saving methods
ata_piix: minor typo and a printk fix
ahci: Changing two module params with static and __read_mostly
Pull percpu changes from Tejun Heo:
"Two smallish changes for percpu. Two patches to remove unused
this_cpu_xor() and one to fix a bug in percpu init failure path so
that it can reach the proper BUG() instead of oopsing earlier"
* 'for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
x86: remove this_cpu_xor() implementation
percpu: remove this_cpu_xor() implementation
percpu: fix bootmem error handling in pcpu_page_first_chunk()
On 64 bit systems the test for negative message sizes is bogus as the
size, which may be positive when evaluated as a long, will get truncated
to an int when passed to load_msg(). So a long might very well contain a
positive value but when truncated to an int it would become negative.
That in combination with a small negative value of msg_ctlmax (which will
be promoted to an unsigned type for the comparison against msgsz, making
it a big positive value and therefore make it pass the check) will lead to
two problems: 1/ The kmalloc() call in alloc_msg() will allocate a too
small buffer as the addition of alen is effectively a subtraction. 2/ The
copy_from_user() call in load_msg() will first overflow the buffer with
userland data and then, when the userland access generates an access
violation, the fixup handler copy_user_handle_tail() will try to fill the
remainder with zeros -- roughly 4GB. That almost instantly results in a
system crash or reset.
,-[ Reproducer (needs to be run as root) ]--
| #include <sys/stat.h>
| #include <sys/msg.h>
| #include <unistd.h>
| #include <fcntl.h>
|
| int main(void) {
| long msg = 1;
| int fd;
|
| fd = open("/proc/sys/kernel/msgmax", O_WRONLY);
| write(fd, "-1", 2);
| close(fd);
|
| msgsnd(0, &msg, 0xfffffff0, IPC_NOWAIT);
|
| return 0;
| }
'---
Fix the issue by preventing msgsz from getting truncated by consistently
using size_t for the message length. This way the size checks in
do_msgsnd() could still be passed with a negative value for msg_ctlmax but
we would fail on the buffer allocation in that case and error out.
Also change the type of m_ts from int to size_t to avoid similar nastiness
in other code paths -- it is used in similar constructs, i.e. signed vs.
unsigned checks. It should never become negative under normal
circumstances, though.
Setting msg_ctlmax to a negative value is an odd configuration and should
be prevented. As that might break existing userland, it will be handled
in a separate commit so it could easily be reverted and reworked without
reintroducing the above described bug.
Hardening mechanisms for user copy operations would have catched that bug
early -- e.g. checking slab object sizes on user copy operations as the
usercopy feature of the PaX patch does. Or, for that matter, detect the
long vs. int sign change due to truncation, as the size overflow plugin
of the very same patch does.
[akpm@linux-foundation.org: fix i386 min() warnings]
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Cc: Pax Team <pageexec@freemail.hu>
Cc: Davidlohr Bueso <davidlohr@hp.com>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org> [ v2.3.27+ -- yes, that old ;) ]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The iterator rbtree_postorder_for_each_entry_safe() relies on pointer
underflow behavior when testing for loop termination. In particular it
expects that
&rb_entry(NULL, type, field)->field
is NULL. But the result of this expression is not defined by a C standard
and some gcc versions (e.g. 4.3.4) assume the above expression can never
be equal to NULL. The net result is an oops because the iteration is not
properly terminated.
Fix the problem by modifying the iterator to avoid pointer underflows.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: <stable@vger.kernel.org> [3.12.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The get_dumpable() return value is not boolean. Most users of the
function actually want to be testing for non-SUID_DUMP_USER(1) rather than
SUID_DUMP_DISABLE(0). The SUID_DUMP_ROOT(2) is also considered a
protected state. Almost all places did this correctly, excepting the two
places fixed in this patch.
Wrong logic:
if (dumpable == SUID_DUMP_DISABLE) { /* be protective */ }
or
if (dumpable == 0) { /* be protective */ }
or
if (!dumpable) { /* be protective */ }
Correct logic:
if (dumpable != SUID_DUMP_USER) { /* be protective */ }
or
if (dumpable != 1) { /* be protective */ }
Without this patch, if the system had set the sysctl fs/suid_dumpable=2, a
user was able to ptrace attach to processes that had dropped privileges to
that user. (This may have been partially mitigated if Yama was enabled.)
The macros have been moved into the file that declares get/set_dumpable(),
which means things like the ia64 code can see them too.
CVE-2013-2929
Reported-by: Vasily Kulikov <segoon@openwall.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Initdata can be const since more than 5 years, using the __initconst
keyword.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We already have list_first_entry(), it makes sense to also add
list_last_entry() for consistency. And we use both helpers in
list_for_each_*().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that we have list_{next,prev}_entry() we can change
list_for_each_entry*() and list_safe_reset_next() to use the new helpers
to improve the readability.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add two trivial helpers list_next_entry() and list_prev_entry(), they
can have a lot of users including list.h itself. In fact the 1st one is
already defined in events/core.c and bnx2x_sp.c, so the patch simply
moves the definition to list.h.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using pool space for DMA buffer, there might be duplicated calling of
gen_pool_alloc() and gen_pool_virt_to_phys() in each implementation.
Thus it's better to add a simple helper function, a compatible one to the
common dma_alloc_coherent(), to save some code.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The LM3630 chip was revised by TI and chip name was also changed to
LM3630A. And register map, default values and initial sequences are
changed. The files, lm3630_bl.{c,h} are replaced by lm3630a_bl.{c,h} You
can find more information about LM3630A(datasheet, evm etc) at
http://www.ti.com/product/lm3630a
Signed-off-by: Daniel Jeong <gshark.jeong@gmail.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LP8555 is one of the LP855x family devices.
This device needs pre_init_device() and post_init_device() driver
structure. It's same as LP8557, so the device configuration code is
shared with LP8557. Backlight outputs are generated from dual DC-DC boost
converters. It's configurable EPROM settings which are defined in the
platform data.
Driver documentation and device tree bindings are updated.
Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fpu_counter in task_struct was used only by sh/x86. Both of these now
carry it in ARCH specific thread_struct, hence this can now be removed
from generic task_struct, shrinking it slightly for other arches.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul Mundt <paul.mundt@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use standard gcc __attribute__((alias(foo))) to define the syscall aliases
instead of custom assembler macros.
This is far cleaner, and also fixes my LTO kernel build.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0255d49184 ("mm: Account for a THP NUMA hinting update as one
PTE update") was added to account for the number of PTE updates when
marking pages prot_numa. task_numa_work was using the old return value
to track how much address space had been updated. Altering the return
value causes the scanner to do more work than it is configured or
documented to in a single unit of work.
This patch reverts that commit and accounts for the number of THP
updates separately in vmstat. It is up to the administrator to
interpret the pair of values correctly. This is a straight-forward
operation and likely to only be of interest when actively debugging NUMA
balancing problems.
The impact of this patch is that the NUMA PTE scanner will scan slower
when THP is enabled and workloads may converge slower as a result. On
the flip size system CPU usage should be lower than recent tests
reported. This is an illustrative example of a short single JVM specjbb
test
specjbb
3.12.0 3.12.0
vanilla acctupdates
TPut 1 26143.00 ( 0.00%) 25747.00 ( -1.51%)
TPut 7 185257.00 ( 0.00%) 183202.00 ( -1.11%)
TPut 13 329760.00 ( 0.00%) 346577.00 ( 5.10%)
TPut 19 442502.00 ( 0.00%) 460146.00 ( 3.99%)
TPut 25 540634.00 ( 0.00%) 549053.00 ( 1.56%)
TPut 31 512098.00 ( 0.00%) 519611.00 ( 1.47%)
TPut 37 461276.00 ( 0.00%) 474973.00 ( 2.97%)
TPut 43 403089.00 ( 0.00%) 414172.00 ( 2.75%)
3.12.0 3.12.0
vanillaacctupdates
User 5169.64 5184.14
System 100.45 80.02
Elapsed 252.75 251.85
Performance is similar but note the reduction in system CPU time. While
this showed a performance gain, it will not be universal but at least
it'll be behaving as documented. The vmstats are obviously different but
here is an obvious interpretation of them from mmtests.
3.12.0 3.12.0
vanillaacctupdates
NUMA page range updates 1408326 11043064
NUMA huge PMD updates 0 21040
NUMA PTE updates 1408326 291624
"NUMA page range updates" == nr_pte_updates and is the value returned to
the NUMA pte scanner. NUMA huge PMD updates were the number of THP
updates which in combination can be used to calculate how many ptes were
updated from userspace.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reported-by: Alex Thorlton <athorlton@sgi.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The same calculation is currently done in three differents places.
Factor that code so future changes has to be made at only one place.
[akpm@linux-foundation.org: uninline vm_commit_limit()]
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The Linux kernel cannot migrate pages used by the kernel. As a result,
kernel pages cannot be hot-removed. So we cannot allocate hotpluggable
memory for the kernel.
ACPI SRAT (System Resource Affinity Table) contains the memory hotplug
info. But before SRAT is parsed, memblock has already started to allocate
memory for the kernel. So we need to prevent memblock from doing this.
In a memory hotplug system, any numa node the kernel resides in should be
unhotpluggable. And for a modern server, each node could have at least
16GB memory. So memory around the kernel image is highly likely
unhotpluggable.
So the basic idea is: Allocate memory from the end of the kernel image and
to the higher memory. Since memory allocation before SRAT is parsed won't
be too much, it could highly likely be in the same node with kernel image.
The current memblock can only allocate memory top-down. So this patch
introduces a new bottom-up allocation mode to allocate memory bottom-up.
And later when we use this allocation direction to allocate memory, we
will limit the start address above the kernel.
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Kamezawa Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When there are processes heavily creating small files while sync(2) is
running, it can easily happen that quite some new files are created
between WB_SYNC_NONE and WB_SYNC_ALL pass of sync(2). That can happen
especially if there are several busy filesystems (remember that sync
traverses filesystems sequentially and waits in WB_SYNC_ALL phase on one
fs before starting it on another fs). Because WB_SYNC_ALL pass is slow
(e.g. causes a transaction commit and cache flush for each inode in
ext3), resulting sync(2) times are rather large.
The following script reproduces the problem:
function run_writers
{
for (( i = 0; i < 10; i++ )); do
mkdir $1/dir$i
for (( j = 0; j < 40000; j++ )); do
dd if=/dev/zero of=$1/dir$i/$j bs=4k count=4 &>/dev/null
done &
done
}
for dir in "$@"; do
run_writers $dir
done
sleep 40
time sync
Fix the problem by disregarding inodes dirtied after sync(2) was called
in the WB_SYNC_ALL pass. To allow for this, sync_inodes_sb() now takes
a time stamp when sync has started which is used for setting up work for
flusher threads.
To give some numbers, when above script is run on two ext4 filesystems
on simple SATA drive, the average sync time from 10 runs is 267.549
seconds with standard deviation 104.799426. With the patched kernel,
the average sync time from 10 runs is 2.995 seconds with standard
deviation 0.096.
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Soft dirty bit allows us to track which pages are written since the last
clear_ref (by "echo 4 > /proc/pid/clear_refs".) This is useful for
userspace applications to know their memory footprints.
Note that the kernel exposes this flag via bit[55] of /proc/pid/pagemap,
and the semantics is not a default one (scheduled to be the default in the
near future.) However, it shifts to the new semantics at the first
clear_ref, and the users of soft dirty bit always do it before utilizing
the bit, so that's not a big deal. Users must avoid relying on the bit in
page-types before the first clear_ref.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For below functions,
- sparse_add_one_section()
- kmalloc_section_memmap()
- __kmalloc_section_memmap()
- __kfree_section_memmap()
they are always invoked to operate on one memory section, so it is
redundant to always pass a nr_pages parameter, which is the page numbers
in one section. So we can directly use predefined macro PAGES_PER_SECTION
instead of passing the parameter.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mpol_to_str() should not fail. Currently, it either fails because the
string buffer is too small or because a string hasn't been defined for a
mempolicy mode.
If a new mempolicy mode is introduced and no string is defined for it,
just warn and return "unknown".
If the buffer is too small, just truncate the string and return, the
same behavior as snprintf().
This also fixes a bug where there was no NULL-byte termination when doing
*p++ = '=' and *p++ ':' and maxlen has been reached.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Chen Gang <gang.chen@asianux.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cpu_up() has #ifdef CONFIG_MEMORY_HOTPLUG code blocks, which call
mem_online_node() to put its node online if offlined and then call
build_all_zonelists() to initialize the zone list.
These steps are specific to memory hotplug, and should be managed in
mm/memory_hotplug.c. lock_memory_hotplug() should also be held for the
whole steps.
For this reason, this patch replaces mem_online_node() with
try_online_node(), which performs the whole steps with
lock_memory_hotplug() held. try_online_node() is named after
try_offline_node() as they have similar purpose.
There is no functional change in this patch.
Signed-off-by: Toshi Kani <toshi.kani@hp.com>
Reviewed-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use helper function to check if we need to deal with oom condition.
Signed-off-by: Qiang Huang <h.huangqiang@huawei.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Pull LED subsystem changes from Bryan Wu:
"LED subsystem updates for 3.13 are basically cleanup and also add a
new driver for PCA9685"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: lp55xx: handle enable pin in driver
leds-gpio: of: led should not be created if its status is disabled
of: introduce of_get_available_child_count
leds: Added driver for the NXP PCA9685 I2C chip
leds: pwm: Remove redundant of_match_ptr
leds: Include linux/of.h header
leds: dac124s085: Remove redundant spi_set_drvdata
leds: lp55xx: enable setting default trigger
leds: blinkm: Remove redundant break
