[WHY]
Programming DPPCLK to the same value currently set may cause
underflow while playing video in certain conditions.
[HOW]
Only program DPPCLK if clock is not the same as the
previous value programmed.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the case where we do have these passed in then we should be using
these instead of the registers - those are only programmed when booting
the adapter as primary.
[How]
Check if fb_base/fb_offset are non-zero. The value of 0 is invalid
for fb_base but is valid for fb_offset on dGPU.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver needs to know PSR state.
[How]
Use GPINT to call to firmware and get psr state.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN hardware sequencer we do actually call ATOM_INIT correctly per
pipe. The workaround is not necessary for command table offloading.
[How]
Drop the workaround since it's not needed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
customer issue: found that for their specific panel, EDID register space
being overwritten during SCDC read write
[how]
customer accepted HDMI 2 features not working - disabled SCDC read/write
as well as HDMI 2 in general based on monitor patch
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently odm scaling calculations are only done when adding initial
odm pipe. Any scaling re-calculations will mess up odm because of this.
This change resolves the problem by updating scaling split logic to
handle odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In the struct dc_panel_patch, we have a field named
manage_secondary_link which is not used by any part of the code. This
commit drops the unused field.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some register defines are redundant or updated
[How]
Update register defines
Remove some redundant defines
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wyatt Wood <Wyatt.Wood@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Sun peng Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
in dcn10_apply_ctx_for_surface(), if we hit !top_pipe_to_program,
pipe_ctx->update_flags could not get cleared.
[How]
Moved clearing pipe_ctx->update_flags logic before if
(!top_pipe_to_program) to gurantee pipe_ctx->update_flags get cleared.
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Several modern displays support HDR/OLED panel, and one of the
interesting changes provided by this technology is the new approach for
handling backlight. More precisely, in the traditional way, we use PWM
to manage display backlight; however, with HDR/OLED we begin to use DP
Aux channel for adjusting the backlight.
This patch, enable the backlight control in HDR/OLED display via DP Aux.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set version is currently not called.
[How]
Add call to set version from copy settings. This
should be the only time this is called as the eDP
caps should never change.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Vendor dongle requires propietary OUI and handshake sequence.
[HOW]
Add a new structure to dc_init_data, to allow creator to pass
an override vendor_oui. This value will be written to DP_SOURCE_OUI
instead of AMD signature, when dpcd_set_source_specific_data is
called.
Signed-off-by: Calvin Hou <Calvin.Hou@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With the fallback case in place for command table offloading via DMCUB
it's no longer an error for the command table to be missing specific
entries.
[How]
Drop the BREAK_TO_DEBUGGER();
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
before we exit early in edp_reciever_ready if we detect that panel
is not edp or below rev 1.2. This will skip the backlight/t7 delay panel
patch.
[how]
edit logic to ensure panel patch is applied regardless of edp rev.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix warning during switching to dpg pause mode for
VCN firmware Version ENC: 1.1 DEC: 1 VEP: 0 Revision: 16
Signed-off-by: James Zhu <James.Zhu@amd.com>
Acked-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GDS clear workaround will cause gfx failure in suspend/resume case.
[ 98.679559] [drm:amdgpu_device_ip_late_init [amdgpu]] *ERROR* late_init of IP block <gfx_v9_0> failed -110
[ 98.679561] PM: dpm_run_callback(): pci_pm_resume+0x0/0xa0 returns -110
[ 98.679562] PM: Device 0000:03:00.0 failed to resume async: error -110
As this workaround is specific to the HW bug of GDS's ECC error
existing in cold boot up, so bypass this workaround in suspend/
resume case after booting up.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With the recent patch to unify VRAM address for driver
table(a83f82e). VF cannot dump table info any more because
SMU_MSG_SetDriverDramAddrHigh/Low were deleted in the
function of smu_update_table.
Therefore, VF also needs to set driver_table address
in smu_hw_init to fix this regression issue.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make use of the better performance here as well.
This patch is only compile tested!
v2: fix calculation bug pointed out by Felix
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Jonathan Kim <Jonathan.Kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This speeds up the access quite a bit from 2.2 MB/s to
2.9 MB/s on 32bit and 12,8 MB/s on 64bit.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Jonathan Kim <Jonathan.Kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should speed up debugging VRAM access a lot.
v2: add HDP flush/invalidate
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Jonathan Kim <Jonathan.Kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only write the _HI register when necessary.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Acked-by: Jonathan Kim <Jonathan.Kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
hwc->conf was designated specifically for AMD APU IOMMU purposes. This
could cause problems in performance and/or function since APU IOMMU
implementation is elsewhere. Also hwc->conf and hwc->config are
different members of an anonymous union so hwc->conf aliases as
hw->last_tag.
Signed-off-by: Jonathan Kim <Jonathan.Kim@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On PowerPC, the compiler will tag object files with whether they
use hard or soft float FP ABI and whether they use 64 or 128-bit
long double ABI. On systems with 64-bit long double ABI, a tag
will get emitted whenever a double is used, as on those systems
a long double is the same as a double. This will prevent linkage
as other files are being compiled with hard-float.
On ppc64, this code will never actually get used for the time
being, as the only currently existing hardware using it are the
Renoir APUs. Therefore, until this is testable and can be fixed
properly, at least make sure the build will not fail.
Signed-off-by: Daniel Kolesa <daniel@octaforge.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Support pause_state for multiple instance, and it will fix vcn2.5 DPG mode
power off issue on instance 1.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU FW will handle the features disablement for baco reset
on Arcturus.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For sriov and pp_onevf_mode, do not send message to set smu
status, because smu doesn't support these messages under VF.
Besides, it should skip smu_suspend when pp_onevf_mode is disabled.
Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently, gcc spews a warning as:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hubbub.c: In function ‘hubbub1_verify_allow_pstate_change_high’:
./include/drm/drm_print.h:316:2: warning: ‘debug_data’ may be used uninitialized in this function [-Wmaybe-uninitialized]
This is because the code checks against a static value although it's
basically a constant and guaranteed to be set.
This patch changes the type prefix from static to const for addressing
the compile warning above and also for letting the compiler optimize
better.
Fixes: 62d591a8e0 ("drm/amd/display: create new files for hubbub functions")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Provide compute queues information in sysfs under /sys/class/kfd/kfd/proc.
The format is /sys/class/kfd/kfd/proc/<pid>/queues/<queue id>/XX where
XX are size, type, and gpuid three files to represent queue size, queue
type, and the GPU this queue uses. <queue id> folder and files underneath
are generated when a queue is created. They are removed when the queue is
destroyed.
Signed-off-by: Amber Lin <Amber.Lin@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
not turning off the mst hub before detection on reboot
causes us to not be able to light up displays with mst hook
[how]
on hw init, see if any displays are lit up. if so, turn them off
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from 14nm, the PLL is built into the PHY and the PLL is mapped
to PHY on 1 to 1 basis. In the code, the DP port is mapped to a PLL that was not
initialized. This causes DP to HDMI dongle to not light up the display.
[How]
Initializations added for PLL2 when creating resources.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
these registers should have been double buffered. SW workaround we will have SW program the more aggressive (lower) values
whenever we are upating this register, so we will not have underflow at expense of less optimzal request pattern.
[How]
there is a driver bug where we don't check for 0, which is uninitialzed HW default. since 0 is smaller than any value we need to program,
driver end up with not programming these registers
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] old panel has been enabled for window driver but not linux.
[How] enable oled panel support for linux. this patch is dc part.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DMUB tracebuffer is useful for understanding DMCUB execution state.
[How]
Add a "show" attribute debugfs so we can loop through the buffer
and print the entries.
The structs for the entry format are defined in the debugfs since
the tracebuffer header no longer exists in the DMUB service.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow is observed when plug in a 4K@60 monitor with
1366x768 eDP due to DPPCLK is too low.
[How]
Limit minimum DPPCLK to 100MHz.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
enum dc_log_type has more than 32 entries. User cannot set larger entries,
like LOG_DSC. Logs from LOG_GAMMA_DEBUG where being printed even though
flag was not enabled, because dal_logger_should_log check erroneously
passed.
[HOW]
Change struct dal_logger.mask and struct dc_init_data.mask to uint64_t.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Having watermark ranges saved inside clk_mgr to be
available for debug at all times would be useful.
Add it to the clk_mgr_internal struct for reference.
Only populated for Renoir, unused for other asics.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
hyperV flag should be passed from dm to DC, and override the
nv12 flip workaround flag.
[How]
Add flag to phy address config struct and pass the value in dm.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous logic is only good for 15W parts. Other configuration
need a smarter logic to match clk levels with pp table in the fuse.
[How]
Cache all 8 DPM level's clock data, find lvl that match each pstate
in the pp table and build input into DML base on that
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
hwss should not guess what type of pipe lock is needed.
The caller of the lock function should know
the right type of pipe lock.
Decouple the setup of global lock outside of pipe control lock
logic.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Engine can be NULL in some cases, so we must not acquire it.
[How]
Check for NULL engine before acquiring.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Previously drain clk was unconstrained and fill clk was constrained on fclk.
We want to change it to fill clk unconstrained and drain clock constrained
to dcfclk.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
new HW engine mapping requirment use in PSP
[how]
report stream_enc_inst
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The break in apply_ctx_interdependent_lock() may potentially
lead to early break from the loop leaving update plane unlocked
[How]
Remove break
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
int i can go out of boundary which will cause crash
[How]
Fixed the maximum value of i to avoid i going out of boundary
Signed-off-by: Peikang Zhang <peikang.zhang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
After locking refactor GSL is not acquired properly
resulting in immediate flip issues.
[How]
Do not copy old GSL state anymore since GSL is acquired
earlier now.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Screen flickering when HDR switches between FP16 and ARGB2101010
[How]
Moved pipe_control_lock so stream update and plane update occur atomically
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Lucy Li <lucy.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DMCUB may be currently executing commands when the reset is
triggered.
Before issuing a reset we should first wait for the DMCUB to finish
its work.
[How]
Send the GPINT command for halting the firmware before reset.
Get the ack for the command then wait for the scratch register to
become the correct value.
We want this to take under ~40us or so at most before we force reset
to cover PHY delay sequence max time.
Each register read will be at least ~1-3us so don't bother using udelay.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The General Purpose Interrupt is used on the DMCUB to pass lightweight
commands via a register to the DMCUB.
This is limited to 32-bit command and 32-bit response.
This will be used for shutting down the firmware in a clean manner.
[How]
Add the command IDs and the data register to correctly format
the commands.
Add the interface functions to dmub_srv for sending and receiving the
commands.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Diagnostics team reported various issues found when enabling warnings as errors
[How]
Fix implicit conversions
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC updates only set type to FULL UPDATE, but doesn't
flag the change
[How]
Add DSC flag update flag
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Eventually want to lock at a higher level in stack.
To do this, we need to be able to isolate the parts that need to be done
after pipe unlock.
[How]
Split out programming that is done post unlock.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The optimized_require flag is needed to set watermarks and clocks lower
in certain conditions. This flag is set to true and then set to false
while programming front end in dcn20.
[HOW]
Do not set the flag to false while disabling plane.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver crash with psr feature enabled due to divide-by-zero error.
This is a regression after rework to calculate static screen frame
number entry time.
[How]
Correct order of operations to avoid divide-by-zero.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why/how]
We found out that the register we read actually gets reset by SMU
after we loose power, meaning this always returns true
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The call to dp_enable_link_phy are using default/invalid values for clock id
and link settings.
[How]
Move workaround code to after its parameter variables are determined.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Must know psr version during runtime.
[How]
Add set psr version message structures.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For sriov, psp ip block has to be initialized before
ih block for the dynamic register programming interface
that needed for vf ih ring buffer. On the other hand,
current psp ip block hw_init function will initialize
xgmi session which actaully depends on interrupt to
return session context. This results an empty xgmi ta
session id and later failures on all the xgmi ta cmd
invoked from vf. xgmi ta session initialization has to
be done after ih ip block hw_init call.
to unify xgmi session init/fini for both bare-metal
sriov virtualization use scenario, move xgmi ta init
to xgmi_add_device call, and accordingly terminate xgmi
ta session in xgmi_remove_device call.
The existing suspend/resume sequence will not be changed.
v2: squash in return fix from Nirmoy
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Frank Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Call the cmd ids for set/get srm according to the sysfs call
v2: Use define for the magic number
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
we need to load SRM before we start HDCP. Because for S3 case the sysfs call will be
after we have already enabled HDCP, so we might not be using the latest SRM
[How]
Set srm before starting HDCP.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSP doesn't have the ability to store SRM in a non-volatile memory. And since
the kernel cannot write to the storage directly, we need usermode to facilitate
this
As per spec the SRM needs to be persistent so this interface is to be
called by the usermode anytime the system goes down/powers on
*boot/resume: load from storage
*shutdown/suspend: save to storage
[How]
Provide a sysfs interface so that the usermode can set/get srm at the right times
save to storage: call "cat /sys/class/drm/card0/device/hdcp_srm > file" after boot and resume
-driver calls psp_get_srm() to get the stored srm and outputs it
load from storage: call "cat file > /sys/class/drm/card0/device/hdcp_srm" before shutdown and suspend
-driver reads the file from sysfs and calls psp_set_srm() to send the SRM to PSP
v2:
-update commit description
-add comment about sysfs file handling in the code
v3:
- squash in use after free fix (Dan Carpenter)
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to support SRM(System Renewability Message)
As per hdcp spec (5.Renewability) SRM needs to be storage in a non-volatile
memory.
PSP owns the checking of SRM but doesn't have the ability to store it in a
non-volatile memory. So we need the kernel driver to facilitate it using the
interface provided by PSP
[How]
Add the interface to the header file, so the driver can use them
v2: update commit description
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need this to create sysfs (followup patch)
[How]
Change the parameter
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If provided we only sync to the BOs reservation
object and no longer to the root PD.
v2: update comment, cleanup amdgpu_bo_sync_wait_resv
v3: use correct reservation object while clearing
v4: fix typo in amdgpu_bo_sync_wait_resv
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No matter what we always need to sync to moves.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow partial invalidation on unallocated PDs. This is useful when we
need to silence faults to stop interrupt floods on Vega.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That we can't find a PD above the root is expected can only happen if
we try to update a larger range than actually managed by the VM.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For the root PD mask can be 0xffffffff as well which would
overrun to 0 if we don't cast it before we add one.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure that we never allocate a page table for an invalidation operation.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The root PD can also contain huge PDEs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to update page tables without any lock held.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For unlocked page table updates we need to be able
to sync to fences of a specific VM.
v2: use SYNC_ALWAYS in the UVD code
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For HMM we need to rework how VM synchronization works, so instead of the filp use VM as job owner.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Explicitly sync VM updates to the moving fence in PDs and PTs.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It needed to be updated as well so it will show the proper values
if you reset to the defaults.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cull out 0 clocks to avoid a warning in DC.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only send non-0 clocks to DC for validation. This mirrors
what the windows driver does.
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We might get different numbers of clocks from powerplay depending
on what the OEM has populated.
v2: add assert for at least one level
Bug: https://gitlab.freedesktop.org/drm/amd/issues/963
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Ask the SMU for the default VDDC curve voltage values. This
properly reports the VDDC values in the OD interface.
v2: only update if the original values are 0
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x
Previously, the syfs functionality for restoring the default powerplay
table was sourcing it's information from the currently-staged powerplay
table.
This patch adds a step to cache the first overdrive table that we see on
boot, so that it can be used later to "restore" the powerplay table
v2: sqaush my original with Matt's fix
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1020
Signed-off-by: Matt Coffin <mcoffin13@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.5.x
[Why]
When we disable a connector we don't explicitly remove it from the module so the
display is still cached(SW) in the hdcp_module.
SST: no issues because we can only have 1 display per link
MST: We have x displays per link, now if we disable 1 we don't remove it from the
module so the module has x display cached(SW).
If we try to enable HDCP, psp verification will fail because we are reporting x
displays while the HW only has x-1 display enabled
[How]
Check the callback for when we disable stream and call remove display.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Remove a backslash symbol accidentally left in increase bpp function
when computing mst dsc configuration.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This workaround is needed only for Navi10 12 Gbps SKUs.
V2: added SMU firmware version guard
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The sdma_queue_count increment should be done before
execute_queues_cpsch(), which calls pm_calc_rlib_size() where
sdma_queue_count is used to calculate whether over_subscription is
triggered.
With the previous code, when a SDMA queue is created,
compute_queue_count in pm_calc_rlib_size() is one more than the
actual compute queue number, because the queue_count has been
incremented while sdma_queue_count has not. This patch fixes that.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In current code we're essentially drawing the cursor on every pipe
that contains it. This only works when the planes have the same
scaling for src to dest rect, otherwise we'll get "double cursor" where
one cursor is incorrectly filtered and offset from the real position.
[How]
Without dedicated cursor planes on DCN we require at least one pipe
that matches the scaling of the current timing.
This is an optimization and workaround for the most common case where
the top-most plane is not scaled but the bottom-most plane is scaled.
Whenever a pipe has a parent pipe in the blending tree whose recout
fully contains the current pipe we can disable the pipe.
This only applies when the pipe is actually visible of course.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Doesn't seem to be used, but add it just in case.
Reviewed-by: Matt Coffin <mcoffin13@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
../drivers/gpu/drm/amd/amdgpu/gfx_v9_4.c:967:35: warning: implicit
conversion from enumeration type 'enum amdgpu_ras_block' to different
enumeration type 'enum ta_ras_block' [-Wenum-conversion]
block_info.block_id = info->head.block;
~ ~~~~~~~~~~~^~~~~
1 warning generated.
Use the function added in commit 828cfa2909 ("drm/amdgpu: Fix amdgpu
ras to ta enums conversion") that handles this conversion explicitly.
Fixes: 4c461d89db ("drm/amdgpu: add RAS support for the gfx block of Arcturus")
Link: https://github.com/ClangBuiltLinux/linux/issues/849
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to do atomic check first, then validate global state.
If not, when connecting both MST and HDMI displays and
set a bad mode via xrandr, system will hang.
[How]
Move drm_dp_mst_atomic_check() to the front of
dc_validate_global_state().
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake on the struct field name link_integiry_check,
fix this by renaming it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
