Record SCU wakeup interrupt in /sys/power/pm_wakeup_irq
The user can further identify the exact wakeup source by using the
following interface:
cat /sys/firmware/scu_wakeup_source/wakeup_src
The above will print the wake groups and the irqs that could have
contributed to waking up the kernel. For example if ON/OFF button was the
wakeup source:
cat /sys/firmware/scu_wakeup_source/wakeup_src
Wakeup source group = 3, irq = 0x1
The user can refer to the SCFW API documentation to identify all the
wake groups and irqs.
Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Extract the scu irq get status code from imx_scu_irq_work_handler and
make into a new function imx_scu_irq_get_status which could be used
by others, such as SECO.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use blocking_notifier_chain instead of atomic_notifier_chain, otherwise
there will be RCU complaint, because unregister/register_virtio_device()
will issue mbox message.
mbox_send_message() is blocking again after received M4 partition reset.
Actually, no need atomic notifier for scu irq notification since this
notifier is called in worker instead of interrupt handler.
[ 389.706645] i2c-rpmsg virtio0.rpmsg-i2c-channel.-1.2: i2c rpmsg driver is removed
[ 389.767362] Wait for remote ready timeout, use first_notify.
[ 389.774084] ------------[ cut here ]------------
[ 389.778729] WARNING: CPU: 0 PID: 397 at kernel/rcu/tree_plugin.h:293 rcu_note_context_switch+0x34/0x338
[ 389.788131] Modules linked in:
[ 389.791195] CPU: 0 PID: 397 Comm: kworker/0:13 Not tainted 5.4.0-rc5-02977-g08f78722f07b #26
[ 389.799633] Hardware name: Freescale i.MX8DXL MEK (DT)
[ 389.805481] Workqueue: events imx_scu_irq_work_handler
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IRQF_NO_SUSPEND flag is set for MU IRQ of IPC work, but with this
flag set, IRQD_WAKEUP_ARMED flag will NOT be set during
suspend_device_irq() phase, then when MU IRQ arrives, it will NOT
wake up system from suspend.
To fix this issue, pm_system_wakeup() is called in general MU IRQ
handler to make sure system can be waked up when MU IRQ arrives.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Include <linux/firmware/imx/sci.h> for the declarations of the
functions exported from this driver. This fixes the following
sparse warnings:
drivers/firmware/imx/imx-scu-irq.c:45:5: warning: symbol 'imx_scu_irq_register_notifier' was not declared. Should it be static?
drivers/firmware/imx/imx-scu-irq.c:52:5: warning: symbol 'imx_scu_irq_unregister_notifier' was not declared. Should it be static?
drivers/firmware/imx/imx-scu-irq.c:97:5: warning: symbol 'imx_scu_irq_group_enable' was not declared. Should it be static?
drivers/firmware/imx/imx-scu-irq.c:130:5: warning: symbol 'imx_scu_enable_general_irq_channel' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The System Controller Firmware (SCFW) controls RTC, thermal
and WDOG etc., these resources' interrupt function are managed
by SCU. When any IRQ pending, SCU will notify Linux via MU general
interrupt channel #3, and Linux kernel needs to call SCU APIs
to get IRQ status and notify each module to handle the interrupt.
Since there is no data transmission for SCU IRQ notification, so
doorbell mode is used for this MU channel, and SCU driver will
use notifier mechanism to broadcast to every module which registers
the SCU block notifier.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
