In HTB offload mode, qdiscs of leaf classes are grafted to netdev
queues. sch_htb expects the dev_queue field of these qdiscs to point to
the corresponding queues. However, qdisc creation may fail, and in that
case noop_qdisc is used instead. Its dev_queue doesn't point to the
right queue, so sch_htb can lose track of used netdev queues, which will
cause internal inconsistencies.
This commit fixes this bug by keeping track of the netdev queue inside
struct htb_class. All reads of cl->leaf.q->dev_queue are replaced by the
new field, the two values are synced on writes, and WARNs are added to
assert equality of the two values.
The driver API has changed: when TC_HTB_LEAF_DEL needs to move a queue,
the driver used to pass the old and new queue IDs to sch_htb. Now that
there is a new field (offload_queue) in struct htb_class that needs to
be updated on this operation, the driver will pass the old class ID to
sch_htb instead (it already knows the new class ID).
Fixes: d03b195b5a ("sch_htb: Hierarchical QoS hardware offload")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210826115425.1744053-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
From Maor Gottlieb
====================
Fix the use of nents and orig_nents in the sg table append helpers. The
nents should be used by the DMA layer to store the number of DMA mapped
sges, the orig_nents is the number of CPU sges.
Since the sg append logic doesn't always create a SGL with exactly
orig_nents entries store a total_nents as well to allow the table to be
properly free'd and reorganize the freeing logic to share across all the
use cases.
====================
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
* 'sg_nents':
RDMA: Use the sg_table directly and remove the opencoded version from umem
lib/scatterlist: Fix wrong update of orig_nents
lib/scatterlist: Provide a dedicated function to support table append
This adds device tree probing support for the PTP module
adjacent to the ethernet module. It is pretty straight
forward, all resources are in the device tree as they
come to the platform device.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is being passed interrupts, then looking up the
same interrupts as GPIOs a second time to convert them into
interrupts and set properties on them.
This is pointless: the GPIO and irqchip APIs of a GPIO chip
are orthogonal. Just request the interrupts and be done
with it, drop reliance on any GPIO functions or definitions.
Use devres-managed functions and add a small devress quirk
to unregister the clock as well and we can rely on devres
to handle all the resources and cut down a bunch of
boilerplate in the process.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the driver to use portable integer types to avoid warnings
during compile testing, including:
drivers/net/ethernet/xscale/ixp4xx_eth.c:721:21: error: cast to 'u32 *' (aka 'unsigned int *') from smaller integer type 'int' [-Werror,-Wint-to-pointer-cast]
memcpy_swab32(mem, (u32 *)((int)skb->data & ~3), bytes / 4);
^
drivers/net/ethernet/xscale/ixp4xx_eth.c:963:12: error: incompatible pointer types passing 'u32 *' (aka 'unsigned int *') to parameter of type 'dma_addr_t *' (aka 'unsigned long long *') [-Werror,-Wincompatible-pointer-types]
&port->desc_tab_phys)))
^~~~~~~~~~~~~~~~~~~~
include/linux/dmapool.h:27:20: note: passing argument to parameter 'handle' here
dma_addr_t *handle);
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the recent ixp4xx cleanups, the ptp driver has gained a
build failure in some configurations:
drivers/net/ethernet/xscale/ptp_ixp46x.c: In function 'ptp_ixp_init':
drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: error: 'IXP4XX_TIMESYNC_BASE_VIRT' undeclared (first use in this function)
Avoid the last bit of hardcoded constants from platform headers
by turning the ptp driver bit into a platform driver and passing
the IRQ and MMIO address as resources.
This is a bit tricky:
- The interface between the two drivers is now the new
ixp46x_ptp_find() function, replacing the global
ixp46x_phc_index variable. The call is done as late
as possible, in hwtstamp_set(), to ensure that the
ptp device is fully probed.
- As the ptp driver is now called by the network driver, the
link dependency is reversed, which in turn requires a small
Makefile hack
- The GPIO number is still left hardcoded. This is clearly not
great, but it can be addressed later. Note that commit 98ac0cc270
("ARM: ixp4xx: Convert to MULTI_IRQ_HANDLER") changed the
IRQ number to something meaningless. Passing the correct IRQ
in a resource fixes this.
- When the PTP driver is disabled, ethtool .get_ts_info()
now correctly lists only software timestamping regardless
of the hardware.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fix a missing include]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter name of hclge_ptp_clean_tx_hwts() in declaration is "dev",
but the definition of this function is used the common name "hdev" as
other functions, so modify it.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the "? :" statement wich max() to simplify code.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of tqp_vector->vector_irq is int, so modify its print format
to "%d".
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve flexibility, simplicity and maintainability to dump info of
every element of tm priority, add a struct hclge_dbg_item array of tm
priority and fill string of every data according to this array.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reconstructs function hclge_ets_validate() to reduce the code
cycle complexity and make code more concise.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reconstructs function hns3_self_test to reduce the code
cycle complexity and make code more concise.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make the format of each member initialization of structure array
clearer, initialize each member on a separate line.
Signed-off-by: Jiaran Zhang <zhangjiaran@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add infrastructure to maintain a pending list of HWRM commands awaiting
completion and reduce the scope of the hwrm_cmd_lock mutex so that it
protects only the request mailbox. The mailbox is free to use for one
or more concurrent commands after receiving deferred response events.
For uniformity and completeness, use the same pending list for
collecting completions for commands that respond via a completion ring.
These commands are only used for freeing rings and for IRQ test and
we only support one such command in flight.
Note deferred responses are also only supported on the main channel.
The secondary channel (KONG) does not support deferred responses.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no longer any callers relying on the old API.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conversion follows this general pattern for most of the calls:
1. The input message is changed from a stack variable initialized
using bnxt_hwrm_cmd_hdr_init() to a pointer allocated and intialized
using hwrm_req_init().
2. If we don't need to read the firmware response, the hwrm_send_message()
call is replaced with hwrm_req_send().
3. If we need to read the firmware response, the mutex lock is replaced
by hwrm_req_hold() to hold the response. When the response is read, the
mutex unlock is replaced by hwrm_req_drop().
If additional DMA buffers are needed for firmware response data, the
hwrm_req_dma_slice() is used instead of calling dma_alloc_coherent().
Some minor refactoring is also done while doing these conversions.
v2: Fix unintialized variable warnings in __bnxt_hwrm_get_tx_rings()
and bnxt_approve_mac()
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use the hwrm_cmd_lock to serialize the update of the
firmware's link status response data and the copying of link status data
to the VF. This won't work when we update the firmware message APIs, so
we use the link_lock mutex instead. All link_info data should be
updated under the link_lock mutex. Also add link_lock to functions that
touch link_info in __bnxt_open_nic() and bnxt_probe_phy(). The locking
is probably not strictly necessary during probe, but it's more consistent.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slices are a mechanism for suballocating DMA mapped regions from the
request buffer. Such regions can be used for indirect command data
instead of creating new mappings with dma_alloc_coherent().
The advantage of using a slice is that the lifetime of the slice is
bound to the request and will be automatically unmapped when the
request is consumed.
A single external region is also supported. This allows for regions
that will not fit inside the spare request buffer space such that
the same API can be used consistently even for larger mappings.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hwrm_req_replace() provides an assignment like operation to replace a
managed HWRM request object with data from a pre-built source. This is
useful for handling request data provided by higher layer HWRM clients.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During firmware crash recovery, it is possible for firmware to respond
to stale HWRM commands that have already timed out. Because response
buffers may be reused, any out of sequence responses need to be ignored
and only the matching seq_id should be accepted.
Also, READ_ONCE should be used for the reads from the DMA buffer to
ensure that the necessary loads are scheduled.
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change constitutes a major step towards supporting multiple
firmware commands in flight by maintaining a separate response buffer
for the duration of each request. These firmware commands are also
known as Hardware Resource Manager (HWRM) commands. Using separate
response buffers requires an API change in order for callers to be
able to free the buffer when done.
It is impossible to keep the existing APIs unchanged. The existing
usage for a simple HWRM message request such as the following:
struct input req = {0};
bnxt_hwrm_cmd_hdr_init(bp, &req, REQ_TYPE, -1, -1);
rc = hwrm_send_message(bp, &req, sizeof(req), HWRM_CMD_TIMEOUT);
if (rc)
/* error */
changes to:
struct input *req;
rc = hwrm_req_init(bp, req, REQ_TYPE);
if (rc)
/* error */
rc = hwrm_req_send(bp, req); /* consumes req */
if (rc)
/* error */
The key changes are:
1. The req is no longer allocated on the stack.
2. The caller must call hwrm_req_init() to allocate a req buffer and
check for a valid buffer.
3. The req buffer is automatically released when hwrm_req_send() returns.
4. If the caller wants to check the firmware response, the caller must
call hwrm_req_hold() to take ownership of the response buffer and
release it afterwards using hwrm_req_drop(). The caller is no longer
required to explicitly hold the hwrm_cmd_lock mutex to read the
response.
5. Because the firmware commands and responses all have different sizes,
some safeguards are added to the code.
This patch maintains legacy API compatibiltiy, implementing the old
API in terms of the new. The follow-on patches will convert all
callers to use the new APIs.
v2: Fix redefined writeq with parisc .config
Fix "cast from pointer to integer of different size" warning in
hwrm_calc_sentinel()
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all firmware messaging functions and definitions to new
bnxt_hwrm.[ch]. The follow-on patches will make major modifications
to these APIs.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code so that __bnxt_hwrm_ver_get() does not call
bnxt_hwrm_do_send_msg() directly. The new APIs will not expose this
internal call. Add a new bnxt_hwrm_poll() to poll the HWRM_VER_GET
firmware call silently. The other bnxt_hwrm_ver_get() function will
send the HWRM_VER_GET message directly with error logs enabled.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The additional response buffer serves no useful purpose. There can
be only one firmware command in flight due to the hwrm_cmd_lock mutex,
which is taken for the entire duration of any command completion,
KONG or otherwise. It is thus safe to share a single DMA buffer.
Removing the code associated with the additional mapping will simplify
matters in the next patch, which allocates response buffers from DMA
pools on a per request basis.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The caller of this function (parisc_driver_remove() in
arch/parisc/kernel/drivers.c) ignores the return value, so better don't
return any value at all to not wake wrong expectations in driver authors.
The only function that could return a non-zero value before was
ipmi_parisc_remove() which returns the return value of
ipmi_si_remove_by_dev(). Make this function return void, too, as for all
other callers the value is ignored, too.
Also fold in a small checkpatch fix for:
WARNING: Unnecessary space before function pointer arguments
+ void (*remove) (struct parisc_device *dev);
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> (for drivers/input)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.
Some reasons why this API should be removed have been given by Julia
Lawall in [2].
A coccinelle script has been used to perform the needed transformation
Only relevant parts are given below.
It has been hand modified to use 'dma_set_mask_and_coherent()' instead of
'pci_set_dma_mask()/pci_set_consistent_dma_mask()' when applicable.
This is less verbose.
Finally, the now useless 'dma_mask' variable has been removed.
It has been compile tested.
@@
expression e1, e2;
@@
- pci_set_dma_mask(e1, e2)
+ dma_set_mask(&e1->dev, e2)
@@
expression e1, e2;
@@
- pci_set_consistent_dma_mask(e1, e2)
+ dma_set_coherent_mask(&e1->dev, e2)
[1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.
Some reasons why this API should be removed have been given by Julia
Lawall in [2].
A coccinelle script has been used to perform the needed transformation
Only relevant parts are given below.
@@ @@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@ @@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@ @@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@
expression e1, e2, e3, e4;
@@
- pci_map_single(e1, e2, e3, e4)
+ dma_map_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2, e3, e4;
@@
- pci_unmap_single(e1, e2, e3, e4)
+ dma_unmap_single(&e1->dev, e2, e3, e4)
@@
expression e1, e2;
@@
- pci_dma_mapping_error(e1, e2)
+ dma_mapping_error(&e1->dev, e2)
[1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
NPC extraction profile marks layer types
NPC_LT_LB_CTAG for CTAG and NPC_LT_LB_STAG_QINQ for
STAG after parsing input packet. Those layer types
can be used to install ntuple filters using
vlan-etype option. Below are the commands and
corresponding behavior with this patch in place.
> alias nt "ethtool -U eth0 flow-type ether"
> nt vlan 5 m 0xf000 action 0
Input packets with outer VLAN id as 5 i.e,
stag packets with VLAN id 5 and ctag packets with
VLAN id as 5 are hit.
> nt vlan-etype 0x8100 action 0
All input ctag packets with any VLAN id are hit.
> nt vlan-etype 0x88A8 action 0
All input stag packets with any VLAN id are hit.
> nt vlan-etype 0x8100 vlan 5 m 0xf000 action 0
All input ctag packets with VLAN id 5 are hit.
> nt vlan-etype 0x88A8 vlan 5 m 0xf000 action 0
All input stag packets with VLAN id 5 are hit.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver crashes when restoring from the Hibernate. In the resume flow,
driver need to clean up the older nic/vec objects and re-initialize them.
Fixes: 8aaa112a57 ("net: atlantic: refactoring pm logic")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the netdev
drivers.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
queue
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2021-08-27
ravindhan Gunasekaran says:
This adds support for Credit-based shaper qdisc offload from
Traffic Control system. It enables traffic prioritization and
bandwidth reservation via the Credit-Based Shaper which is
implemented in hardware by i225 controller.
Patch 1/3 adds a default cycle-time for TSN mode to be configured.
Patch 2/3 helps to separate TSN mode programming on the fly and
during reset sequence. It also simplifies handling features flags
for various TSN modes supported by i225 in the driver.
Patch 3/3 adds support for IEEE802.1Qav(CBS) standard
implemented in i225 HW. Two sets of CBS HW shapers are present
in i225 and driver enables them in the two high priority queues.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The queues can be freed in ionic_close(). They need to be recreated
after ionic_open(). It doesn't need to replay the whole config. It
only needs to create the timestamping queues again.
Signed-off-by: Allen Hubbe <allenbh@pensando.io>
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the hwstamp configuration use of queue_lock up
a level to simplify use and error handling.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the queue configuration lock to ionic_open() and
ionic_stop() so that they don't collide with other in parallel
queue configuration actions such as MTU changes as can be
demonstrated with a tight loop of ifup/change-mtu/ifdown.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the ctx struct has the new mac address before
any save operations happen.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the heartbeat check will already have complained about
the firmware status, don't bother complaining about the
DEVCMD failing. We'll keep the print message but demote it
to a debug messages so that we normally no longer see it.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases of fw_down it was called because there was a
fw_generation change, and the firmware is already back up.
In order to keep the down time to a minimum, don't wait for
the next watchdog polling cycle, fire another watchdog off
as soon as we can - an out-of-cycle check won't hurt, and
may well speed up the recovery.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some required spaces in comment for cleanup.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some local variable declarations are no need to add "static", so remove it.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hclge_tm_dwrr_cfg() will be called twice in function
hclge_ieee_setets() when map_changed is true, the calling flow is
hclge_ieee_setets()
hclge_map_update()
| hclge_tm_schd_setup_hw()
| hclge_tm_dwrr_cfg()
hclge_notify_init_up()
hclge_tm_dwrr_cfg()
It is no need to call hclge_tm_dwrr_cfg() twice actually, so just
return after calling hclge_notify_init_up().
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, function hclge_check_port_speed() uses switch/case statement
to get speed bit according to speed. To reuse this part of code and
improve code readability and maintainability, add a new function
hclge_get_speed_bit() to get speed bit according to map relationship
of speed and speed bit defined in array speed_bit_map.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hclgevf_parse_capability() will add more if statement in the
future, to improve code readability, maintainability and simplicity,
refactor this function by using a bit mapping array of IMP capabilities
and driver capabilities.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hclge_parse_capability() uses too many if statement, and
it may add more in the future. To improve code readability, maintainability
and simplicity, refactor this function by using a bit mapping array of IMP
capabilities and driver capabilities.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a trace to get the info of pf responds to the mailbox message of vf.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Count packets dropped due to buffer or skb allocation errors.
Report as part of rx_dropped.
v2: drop the ethtool -S entry [Vladimir]
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
bnxt may discard packets if Rx completions are consumed
in an attempt to let netpoll make progress. It should be
extremely rare in practice but nonetheless such events
should be counted.
Since completion ring memory is allocated dynamically use
a similar scheme to what is done for HW stats to save them.
Report the stats in rx_dropped and per-netdev ethtool
counter. Chances that users care which ring dropped are
very low.
v3: only save the stat to rx_dropped on reset,
rx_total_netpoll_discards will now only show drops since
last reset, similar to other "total_discard" counters.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When we enabled auxiliary input/output support for the E810 device, we
forgot to add logic to restart the output when we change time. This is
important as the periodic output will be incorrect after a time change
otherwise.
This unfortunately includes the adjust time function, even though it
uses an atomic hardware interface. The atomic adjustment can still cause
the pin output to stall permanently, so we need to stop and restart it.
Introduce wrapper functions to temporarily disable and then re-enable
the clock outputs.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sunitha D Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement support for Credit-based shaper(CBS) Qdisc hardware
offload mode in the driver. There are two sets of IEEE802.1Qav
(CBS) HW logic in i225 controller and this patch supports
enabling them in the top two priority TX queues.
Driver implemented as recommended by Foxville External
Architecture Specification v0.993. Idleslope and Hi-credit are
the CBS tunable parameters for i225 NIC, programmed in TQAVCC
and TQAVHC registers respectively.
In-order for IEEE802.1Qav (CBS) algorithm to work as intended
and provide BW reservation CBS should be enabled in highest
priority queue first. If we enable CBS on any of low priority
queues, the traffic in high priority queue does not allow low
priority queue to be selected for transmission and bandwidth
reservation is not guaranteed.
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Separates the procedure done during reset from applying a
configuration, knowing when the code is executing allow us to
separate the better what changes the hardware state from what
changes only the driver state.
Introduces a flag for bookkeeping the driver state of TSN
features. When Qav and frame-preemption is also implemented
this flag makes it easier to keep track on whether a TSN feature
driver state is enabled or not though controller state changes,
say, during a reset.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Sets default values for each queue cycle start and cycle end.
This allows some simplification in the handling of these
configurations as most TSN features in i225 require a cycle
to be configured.
In i225, cycle start and end time is required to be programmed
for CBS to work properly.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Aravindhan Gunasekaran <aravindhan.gunasekaran@intel.com>
Signed-off-by: Mallikarjuna Chilakala <mallikarjuna.chilakala@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver didn't take the lock while flushing the Tx tracker, which
could cause a race where one thread is trying to read timestamps out
while another thread is trying to read the tracker to check the
timestamps.
Avoid this by ensuring that flushing is locked against read accesses.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
We have code in the ice driver which allocates the pin_config structure
if n_pins is > 0, but we never set n_pins to be greater than zero.
There's no reason to keep this code until we actually have pin_config
support. Remove this. We can re-add it properly when we implement
support for pin_config for E810-T devices.
Fixes: 172db5f91d ("ice: add support for auxiliary input/output pins")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver accidentally copied the ice_for_each_rxq iterator when
implementing enablement of the ptp_tx bit for the Tx rings. We still
load the Tx rings and set the ptp_tx field, but we iterate over the
count of the num_rxq.
If the number of Tx and Rx queues differ, this could either cause
a buffer overrun when accessing the tx_rings list if num_txq is greater
than num_rxq, or it could cause us to fail to enable Tx timestamps for
some rings.
This was not noticed originally as we generally have the same number of
Tx and Rx queues.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enhancing the mailbox scope to support important configurations
like enabling scheduled LMTST, disable LMTLINE prefetch, disable
early completion for ordered LMTST, as per request from the
application. On FLR these configurations will be reset to default.
This patch also adds the 95XXO silicon version to octeontx2 silicon
list.
Signed-off-by: Harman Kalra <hkalra@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The parameter cmd in function definition of hns3_dbg_bd_file_init and
hns3_dbg_common_file_init is used type u32, this patch uniforms them
in function declaration to type u32 too.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some repetitive macros have same meaning and value, this patch
merges them to make code clean.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch packages two new function to simplify the function
hclgevf_mbx_handler, and it can reduce the code cycle complexity
and make code more concise.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The param msg_q is redundant, copy &req->msg to
hdev->arq.msg_q[hdev->arq.tail] directly makes code clean.
So removes the redundant param msg_q.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use memcpy to copy req->msg.resp_data to resp->additional_info,
to simplify the code and improve a little efficiency.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the redundant param mbx_event_pending.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve the readability and maintainability, add hns3_state_init() to
initialize the state, and this new function will be used to add more state
initialization in the future.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To improve code readability, replace digital numbers of mac speeds
defined by firmware command with macros.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch series contains various fixes, additions and improvements to
mlx5 software steering.
Patch 1:
adds support for REMOVE_HEADER packet reformat - a new reformat type
that is supported starting with ConnectX-6 DX, and allows removing an
arbitrary size packet segment at a selected position.
Patches 2 and 3:
add support for VLAN pop on TX and VLAN push on RX flows.
Patch 4:
enables retransmission mechanism for the SW Steering RC QP.
Patch 5:
does some improvements to error flow in building STE array and adds
a more informative printout of an invalid actions sequence.
Patch 6:
improves error flow on SW Steering QP error.
Patch 7:
reduces the log level of a message that is printed when a table is
connected to a lower/same level destination table, as this case proves to
be not as rare as it was in the past.
Patch 8:
adds missing support for matching on IPv6 flow label for devices
older than ConnectX-6 DX.
Patch 9:
replaces uintN_t types with kernel-style types.
Patch 10:
allows for using the right API for updating flow tables - if it is
a FW-owned table, then FW API will be used.
Patch 11:
adds support for 'ignore_flow_level' on multi-destination flow
tables that are created by SW Steering.
Patch 12:
optimizes FDB RX steering rule by skipping matching on source port,
as the source port for all incoming packets equals to wire.
Patch 13:
is a small code refactoring - it merges several DR_STE_SIZE enums
into a single enum.
Patch 14:
does some additional refactoring and removes HW-specific STE type
from NIC domain.
Patch 15:
removes rehash ctrl struct from dr_htbl struct and saves some memory.
Patch 16:
does a more significant improvement in terms of memory consumption
and was able to save about 1.6 Gb for 8M rules.
Patch 17:
adds support for update FTE, which is needed for cases where there
are multiple rules with the same match.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAmEoF8wACgkQSD+KveBX
+j7+oAgAvNXfSvagaGpqIqSKY39u4YGoaJzMga80Lj6AtnY3PBTUQUY3B7fReiqg
8ZwYU9fCEVk4TFRTRvZOTph/lRw87SEAtFUXNLYlYrckDehQN2Jxw25uPLgy5cws
pYkuBiljpMUf/Fqtk2x9i2gaV3eMjA9Hr8beP4OUWAfoFM/BOIBByK4hcb5qRjBf
UUOOLCRS7QIktusnlc0jMlNJx0J2v5rNHH3aNKzsyqXknB9yhy49CUsQ5Y85bB7N
tb41eFeV4VniDXU5MAuildgCv/KZ3FZUyPuOh5qwO7T8K+eUm1laCC0/sojWRAy9
25BuhdpMn/OhCpyNGbn6Frs7C7+fmA==
=Fzxb
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2021-08-26' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
This patch series contains various fixes, additions and improvements to
mlx5 software steering.
Patch 1:
adds support for REMOVE_HEADER packet reformat - a new reformat type
that is supported starting with ConnectX-6 DX, and allows removing an
arbitrary size packet segment at a selected position.
Patches 2 and 3:
add support for VLAN pop on TX and VLAN push on RX flows.
Patch 4:
enables retransmission mechanism for the SW Steering RC QP.
Patch 5:
does some improvements to error flow in building STE array and adds
a more informative printout of an invalid actions sequence.
Patch 6:
improves error flow on SW Steering QP error.
Patch 7:
reduces the log level of a message that is printed when a table is
connected to a lower/same level destination table, as this case proves to
be not as rare as it was in the past.
Patch 8:
adds missing support for matching on IPv6 flow label for devices
older than ConnectX-6 DX.
Patch 9:
replaces uintN_t types with kernel-style types.
Patch 10:
allows for using the right API for updating flow tables - if it is
a FW-owned table, then FW API will be used.
Patch 11:
adds support for 'ignore_flow_level' on multi-destination flow
tables that are created by SW Steering.
Patch 12:
optimizes FDB RX steering rule by skipping matching on source port,
as the source port for all incoming packets equals to wire.
Patch 13:
is a small code refactoring - it merges several DR_STE_SIZE enums
into a single enum.
Patch 14:
does some additional refactoring and removes HW-specific STE type
from NIC domain.
Patch 15:
removes rehash ctrl struct from dr_htbl struct and saves some memory.
Patch 16:
does a more significant improvement in terms of memory consumption
and was able to save about 1.6 Gb for 8M rules.
Patch 17:
adds support for update FTE, which is needed for cases where there
are multiple rules with the same match.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support for update FTE, which is needed for cases where there are
multiple rules with the same match. In such case fs_core will merge the
actions and call update FTE to update current FTE. Since we don't want to
disrupt the traffic, we will add the new duplicate rule, and only then
remove the old duplicate rule.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
To track each STE of the rule a rule member was allocated, each
member would point to one STE. This means that we would allocate
40B (rule member) * number of STEs per rule.
To reduce this per rule allocation we use the STE tree pointers
for next_htbl and pointing STE to navigate the tree, this allows
us to keep only the pointer to the last STE of rule (always unique).
From the last rule STE we are able to traverse and rebuild all of
the STEs that construct the rule.
In our testing with 8M rules, each consisting of 7 STES, we were able
to reduce 1.6GB of memory.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The calculations to decide for the maximum allowed collision threshold
are simple and there is no reason to save them on the htbl struct.
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Instead of using the HW specific STEv0 type, it is better to use
an enum to indicate if this is an RX or TX nic domain.
This means that now we will need to convert the nic domain type
to the corresponding STE type.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Merge DR_STE_SIZE enums - no need for a separate enum for reduced STE size.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The FDB RX pipe is connected to the wire and the source port for all
incoming packets equals to wire, single uplink port per PF, this means
there is no point of matching on the source port in such case.
Once we recognize such case, we will optimize the RX steering rule.
Note that in such case we clean both source_eswitch_owner_vhca_id and
source_port.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When creating an FTE, we might need to create multi-destination flow table,
which is eventually created by FW. In such case, this FW table should
include all the FTE properties as requested by the upper layer, including
the ability to point to another flow table with level lower or equal to
the current table - indicated by the "ignore_flow_level" property.
Signed-off-by: Chris Mi <cmi@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Need to call the DR API only when it is DR table.
To update FW-owned table the driver should call the FW API.
Signed-off-by: Erez Shitrit <erezsh@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add missing support for matching on IPv6 flow label for STEv0.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
There are usecases with Connection Tracking that have such connection
as default, printing this warning in dmesg confuses the user.
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In the event of SW steering QP entering error state, SW steering
cannot insert more rules, and will silently ignore the insertion
after issuing a warning.
Signed-off-by: Yuval Avnery <yuvalav@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Under high stress, SW steering might get stuck on polling for completion
that never comes.
For such cases QP needs to have protocol retransmission mechanism enabled.
Currently the retransmission timeout is defined as 0 (unlimited). Fix this
by defining a real timeout.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Enable pop VLAN action in TX and push VLAN in RX.
These actions are supported only on STEv1.
On TX: when a host sends a packet, VLAN is popped at the beginning.
On RX: just before passing the packet to the host the VLAN is pushed.
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Split modify vlan state in the actions state machine to pop vlan
and push vlan states. This enables using of pop/push vlan without
restrictions (e.g. pop vlan on TX in STEv1).
Signed-off-by: Muhammad Sammar <muhammads@nvidia.com>
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
ConnectX supports offloading of various encapsulations and decapsulations
(e.g. VXLAN), which are performed by 'Packet Reformat' action. Starting
with ConnectX-6 DX, a new reformat type is supported - REMOVE_HEADER, which
allows deleting an arbitrary size chunk at the selected position in the packet.
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In line 849 (#1), "mlx5dr_htbl_put(cur_htbl);" drops the reference to
cur_htbl and may cause cur_htbl to be freed.
However, cur_htbl is subsequently used in the next line, which may result
in an use-after-free bug.
Fix this by calling mlx5dr_err() before the cur_htbl is put.
Signed-off-by: Wentao_Liang <Wentao_Liang_g@163.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If link aggregation is used within stack devices driver rejects encap
rules if PF of the VF tunnel device is down. This happens because route
resolved for other PF and its eswitch instance is used to determine
correct vport.
To fix that use devcom feature to retrieve other eswitch instance if
failed to find vport for the 1st eswitch and LAG is active.
Fixes: 10742efc20 ("net/mlx5e: VF tunnel TX traffic offloading")
Signed-off-by: Dmytro Linkin <dlinkin@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When indirect forward group is created, flow is added with vhca id but
without setting vhca id valid flag which violates the PRM.
Fix by setting the missing flag, vhca id valid.
Fixes: 34ca65352d ("net/mlx5: E-Switch, Indirect table infrastructure")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
After neigh-update-add failure we are still with a slow path rule but
the driver always assume the rule is an fdb rule.
Fix neigh-update-del by checking slow path tc flag on the flow.
Also fix neigh-update-add for when neigh-update-del fails the same.
Fixes: 5dbe906ff1 ("net/mlx5e: Use a slow path rule instead if vxlan neighbour isn't available")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The call to mlx5_unregister_device() means that mlx5_core driver is
removed. In such scenario, we need to disregard all other flags like
attach/detach and forcibly remove all auxiliary devices.
Fixes: a5ae8fc905 ("net/mlx5e: Don't create devices during unload flow")
Tested-and-Reported-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When handling FIB_EVENT_ENTRY_REPLACE event for a new multipath route,
lag activation can be missed if a stale (struct lag_mp)->mfi pointer
exists, which was associated with an older multipath route that had been
removed.
Normally, when a route is removed, it triggers mlx5_lag_fib_event(),
which handles FIB_EVENT_ENTRY_DEL and clears mfi pointer. But, if
mlx5_lag_check_prereq() condition isn't met, for example when eswitch is
in legacy mode, the fib event is skipped and mfi pointer becomes stale.
Fix by resetting mfi pointer to NULL in mlx5_deactivate_lag().
Fixes: 8a66e45859 ("net/mlx5: Change ownership model for lag")
Signed-off-by: Dima Chumak <dchumak@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The GRO configuration is enabled by default after reset. This
is incorrect and should be restored to the user-configured value.
So this restoration is added during reset initialization.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, the cmd index is obtained in debugfs by comparing file names.
However, this method may cause errors when processing more complex file
names. So, change this method by saving cmd in private data and comparing
it when getting cmd index in debugfs for optimization.
Fixes: 5e69ea7ee2 ("net: hns3: refactor the debugfs process")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
Fixes: c6075b1934 ("net: hns3: Record VF vlan tables")
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.
The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fc ("net: hns3: uninitialize command queue while unloading PF driver")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LiteX is a soft system-on-chip that targets FPGAs. LiteETH is a basic
network device that is commonly used in LiteX designs.
The driver was first written in 2017 and has been maintained by the
LiteX community in various trees. Thank you to all who have contributed.
Co-developed-by: Gabriel Somlo <gsomlo@gmail.com>
Co-developed-by: David Shah <dave@ds0.me>
Co-developed-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Gabriel Somlo <gsomlo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a function for what has been magic register writes so far.
It's based on recent changes to vendor drivers r8101, r8168, r8125,
and deals with events that trigger an early ASPM L1 exit.
Description of the bits has been kindly provided by Realtek.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If otx2_mbox_get_rsp() fails, otx2_set_flowkey_cfg() need return an
error code.
Fixes: e793836545 ("octeontx2-pf: Fix algorithm index in MCAM rules with RSS action")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f ("cxgb4: Add debugfs facility to inject FL starvation")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
