"compatible", "#address-cells" and "#size-cells" for USB PHY are
already described in the SOM DTS. Remove these duplicate entries.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add support for the PCI express bus available on MX6 SabreSDP.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
It is not a good approach to have the USB PHY nodes inside imx27.dtsi since
the USB PHYs on mx27 are not internal to the SoC.
Place the USB PHY nodes in the board dts files instead.
Also, each board may have a different clock source for the USB PHY, so do not
hardcode it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
USB Host1, Host2 and OTG are gated via 'usb_ipg_gate' clock, so fix it in order
to avoid the following kernel oops:
usbcore: registered new interface driver usb-storage
10024000.usb supply vbus not found, using dummy regulator
Unhandled fault: external abort on non-linefetch (0x808) at 0xf4424184
Internal error: : 808 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc1-26325-g971f9fd-dirty #64
task: c7829aa0 ti: c7836000 task.ti: c7836000
PC is at ci_hdrc_probe+0x3a4/0x634
LR is at ci_hdrc_probe+0x100/0x634
pc : [<c036cc78>] lr : [<c036c9d4>] psr: 60000013
sp : c7837d48 ip : 00000001 fp : 00000000
r10: 00000000 r9 : 00000000 r8 : c791b6c0
r7 : c7945000 r6 : f4424000 r5 : c7945010 r4 : c794e010
r3 : f4424184 r2 : 00000000 r1 : 8c000004 r0 : 0c000004
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0005317f Table: a0004000 DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc78361c0)
Stack: (0xc7837d48 to 0xc7838000)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The hardware is better described if we place the PMIC IRQ GPIO into its own
pingroup.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
imx27-pdk has a MC13783 PMIC connected to CSPI2 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds devicetree node and pinctrl group for I2C1.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch sorts nodes by name and moves "iomux" configuration at
the bottom of file.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds a regulator node and pinctrl group for USB OTG.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Move "hog" pins into corresponded pin groups for eSDHC1, eSDHC2,
eCSPI1, gpio-keys, regulator-fixed and codec clock.
Additionally, this patch fixes GPIO active level definition for
USB regulator.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch allow to define partitions onto NFC in user defined
devicetrees.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch enables UART1 on the phyFLEX connector (i.MX6 uart3).
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The pins labeled UART1 on the module connector are wired to i.MX6 uart3.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds the TLV320, STMPE811, RTC8564, and MX1037 ICs to the I2C2 bus.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Note that the fec driver code currently hard-codes an active-low
reset, regardless of the flags in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch enables the red and green GPIO LEDs on Phytec phyFLEX i.MX6 modules.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The PBA-B-01 carrier board can be equipped with either Quad or DualLite/Solo
phyFLEX i.MX6 modules (PFL-A-02).
This moves all common devices into imx6qdl-phytec-pbab01.dtsi. The SoC specific
device trees then just include the pfla01 and pbab01 dtsi files corresponding
to the SoC variant.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Provide an entry for the UART1 pin muxing.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds support for Digi ConnectCore® i.MX51/Wi-i.MX51 SOM
and basic support for the ConnectCore for i.MX51 JumpStart Kit.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch converts all i.MX WEIM users to use single naming style
for devices.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add initial Toradex Colibri VF61 board support. Ethernet, UART
and SDHC cards are working. Cache latencies need to be a bit
higher than vf610.dtsi suggests. Those values are validated
by running multiple memory tests.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
imx27-pdk has 128 MB of DRAM. Pass the memory range in dt.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds display control signal definitions.
These fields are not used in the driver yet, but will be used for
reference to indicate the polarity of the signals.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Use GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW instead of 0 and 1.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fix a copy & paste error: on duckbills the GPIO used for resetting
the ethernet phy differs from FSL's MX28EVK board.
Reported-by: Stefan Wahren <info@lategoodbye.de>
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
I2SE's duckbills are only equipped with a micro SD card slot and
thus only provide a 4-bit interface.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested by pinging from the host PC to the imx51-babbage via a g_ether
connection.
Signed-off by: Dave Ebright <dave.ebright@parsons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This adds devicetree node for VF610, and there are 8 channels
supported.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This IP module is always present and has no external connections.
There is no reason to disable it in the device tree.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
mx25pdk has a sgtl5000 codec connected to the I2C1 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Set 'ti,set-rate-parent' property for the dpll4_m5x2_mul_ck clock, which
is used for the ISP functional clock. This fixes the OMAP3 ISP driver's
clock rate configuration, which needs the rate to be propagated properly
to the divider node (dpll4_m5_ck).
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
We need to use set-rate-parent for dpll4_m5 clock path, so use the
ti,fixed-factor-clock version which supports set-rate-parent property.
The set-rate-parent flag itself is set in the following patch, this one
just changes the clock driver to ti,fixed-factor-clock without any other
changes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Use the ti,fixed-factor-clock version so that autoidle for
dpll_per_clkdcoldo is properly controlled after power management code
is introduced. Without this the clock may be held active even when
it is gated.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
To silence the warning
cpufreq_cpu0: failed to get cpu0 regulator: -19
from the cpufreq driver regarding a missing regulator,
add a fixed regulator to the DT.
Zynq does not support voltage scaling and the CPU rail should always be
supplied with 1 V, hence it is added in the SOC-level dtsi.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Marvell Armada 375 SoCs contains two EHCI controllers. This commit
adds the Device Tree description of these interfaces at the SoC level,
and also enables the USB2 port on the Armada 375 DB platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1400149062-32661-18-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 375 SoCs contain a xHCI controller. This commit
adds the Device Tree description of this interfaces at the SoC level,
and also enables the USB3 port on the Armada 375 DB platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1400149062-32661-17-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 38x SoCs contains one EHCI controller. This commit
adds the Device Tree description of this interface at the SoC level,
and also enables the USB2 port on the Armada 385 DB platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1400149062-32661-16-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Marvell Armada 38x SoCs contains two xHCI controllers. This commit
adds the Device Tree description of those interfaces at the SoC level,
and also enables the two USB3 ports on the Armada 385 DB platform and
one USB3 port on the Armada 385 RD platform.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Link: https://lkml.kernel.org/r/1400149062-32661-15-git-send-email-gregory.clement@free-electrons.com
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Create DTS files to describe the Marvell OpenRD boards.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1399836639-1918-1-git-send-email-andrew@lunn.ch
Tested-by: Francois Lorrain <francois.lorrain@gmail.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Added TPS65090 regulator related nodes to Snow board.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the device tree to support Toradex Colibri T30, a
computer on module which can be used on different carrier boards.
The module consists of a Tegra 30 SoC, two PMIC, DDR3L RAM, eMMC,
a LM95245 temperature sensor and an AX88772B USB Ethernet
Controller. Furthermore, there is a STMPE811 and SGTL5000 audio
codec which are not yet supported. Anything that is not self
contained on the module is disabled by default.
The device tree for the Evaluation Board includes the modules
device tree and enables the supported pheripherials of the carrier
board (the Evaluation Board supports almost all of them).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The A31 SoC has a different pin controller for PL and PM banks.
Define this new controller in the device tree.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add DT definitions for PRCM (Power/Reset/Clock Management) clock and reset
controller subdevices.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux for hdq/1wire on
am43x epos evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB pinmux information and USB modes
for the USB controllers.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for the Super Speed USB controllers, omap-control-usb,
USB2 PHY and USB3 PHY devices.
Remove ocp2scp1 address space from hwmod data as it is
now provided via device tree.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This clock gate description is missing in the older Reference manuals.
It is present on the SoC to provide 960MHz reference clock to the
internal USB PHYs.
Reference: DRA75x_DRA74x_ES1.1_NDA_TRM_vO.pdf, pg. 900,
Table 3-812. CM_COREAON_L3INIT_60M_GFCLK_CLKCTRL
Use l3init_960m_gfclk as parent of usb_otg_ss1_refclk960m and
usb_otg_ss2_refclk960m.
CC: Benoît Cousson <bcousson@baylibre.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The USB2 PHY driver expects named clocks for wakeup clock
and reference clock. Provide this information for USB2 PHY
nodes in OMAP4 and OMAP5 SoC DTS.
CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for OCP2SCP3 bus, SATA controller and SATA PHY.
[Roger Q] Clean up. Updated IRQ for interrupt crossbar.
CC: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for sata.
[Roger Q] Clean up.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
G2D power domain also controls the CMU block of G2D. Since
clock registers can be accessed anytime for viewing
clk_summary, it can cause a system crash if g2d power domain
is disabled.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
MAU powerdomain provides clocks for Audio sub-system block.
This block comprises of the I2S audio controller, audio DMA
blocks and Audio sub-system clock registers.
Right now, there is no way to hook up power-domains with
clock providers. During late boot when this power-domain
gets disabled, we get following external abort.
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This change places MDMA1 in disabled node for Exynos5420.
If MDMA1 region is configured with secure mode, it makes
the boot failure with the following on smdk5420 board.
("Unhandled fault: imprecise external abort (0x1406) at 0x00000000")
Thus, arndale-octa board don't need to do the same thing anymore.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Javi Merino <javi.merino@arm.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Instead of hardcoding the SYSRAM details for each SoC,
pass this information through device tree (DT) and make
the code SoC agnostic. Generic DT SRAM bindings are
used for achieving this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The APP4 EVB1 development boards embeds an A31, together with some NAND, one SD
card slot, and one SDIO + UART WiFi and Bluetooth chip, a few I2C buses, USB,
and a LCD display.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The A31 has two ECHI/OHCI controllers, and one OHCI-only phy-less controller.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The USB clocks of the A31 seems to be parented to the 24MHz oscillator, and
handle the clocks for the USB phys and OHCI devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
In the comments, LCD pins 16-23 were numbered in the wrong order.
Fix this and use proper pinmux constants for all entries while we
are at it.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Cc: Benoit Parrot <bparrot@ti.com>
Tested-by: Darren Etheridge <detheridge@ti.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change makes the DTS consistent with the platform data
that exists in board-marzen.c.
Empirically it does not appear to be necessary.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There's no need to duplicate the interrupt-parent property in all DT
nodes as the kernel automatically walks parent nodes to find the
property. Specify it once in the root node only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
NVIDIA SHIELD is a portable Android console containing a Tegra 4 SoC with
2GB RAM and a 720p panel.
The following hardware is enabled by this device tree: UART, eMMC, USB
(needs external power), PMIC, backlight, joystick, SD card, GPIO keys.
DSI panel, HDMI output, charger, self-powered USB, audio, wifi bluetooth
are not supported yet but might be by future patches (likely in that
order).
Touch panel and sensors will probably never be supported.
Initrd addresses are hardcoded to match the static values used by the
bootloader, since it won't add them for us. All the same, a kernel
command-line is provided to replace the one passed by the
bootloader which is filled with garbage.
NVIDIA SHIELD is typically booted with an appended DTB to avoid
modifications made by the bootloader.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[swarren, fixed gpio-keys child node sort order, patch description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The R7 tv-dongle is an A10s based hdmi tv dongle, with 1G RAM, 4G nand flash,
and rtl8189es sdio wifi. It has a standard male hdmi connector, an USB host
port using an USB-A receptacle and a micro-usb receptacle for both power
and USB OTG.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As there are no pull-up resistors on the board itself it can be useful to
use the SoC pad pull-up to be able to easily connect usual i2c devices.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Argument 3 (OUT) and 4 (ICPLL) of the atmel,pll-clk-output-ranges were missing.
Also, the at91sam9rl doesn't really have a by 3 divisor.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add ssc2 support, ssc2 pinctrl and clocks for the three SSCs.
Also add support for the programmable clocks.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Argument 3 (OUT) and 4 (ICPLL) of the atmel,pll-clk-output-ranges were missing.
Also, the at91sam9261 doesn't really have a by 3 divisor.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define the Henninger board dependent part of the MSIOF0 device node.
Add device node for Renesas R2A11302FT PMIC for which no bindings exist yet.
Based on the Koelsch MSIOF device tree patch by Geert Uytterhoeven.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the SDHI0/2 device nodes along with
the necessary voltage regulators (note that the Vcc regulators are dummy -- they
are required but don't actually exist on the board). Also, GPIOs have to be used
for the CD and WP signals due to the SDHI driver constraints...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Introduce the grf syscon and convert the pinctrl drivers for rk3066 and rk3188
to use it, instead of mapping the grf registers themselfs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Max Schwarz <max.schwarz@online.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add the missing 'compatible' property to device tree root node of
- rk3066a-bqcurie2.dts
- rk3188-radxarock.dts
and document the new values.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Adds the google peach-pit board dts file which uses
exynos5420 SoC.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adding labels to nodes which do not have it yet in exynos5420.
This is done so as to use reference based node updation in board
files.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Adds the PWM nodes to 5420 pinctrl dtsi file.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables the rear facing camera (s5c73m3) on TRATS2 board
by adding the I2C0 bus controller, s5c73m3 sensor, MIPI CSI-2 receiver
and the sensor's voltage regulator supply nodes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Remove unused /camera/clock-controller node and add required clock
properties to the camera node. This is required for a clock provider
that will be referenced by image sensor devices.
Also add required clock related changes to s5k6a3 device node and
afvdd regulator supply.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The i2c_ak8975 controller uses label i2c8.
This alias is already used for I2C controller 8 defined
in file arch/arm/boot/dts/exynos4.dtsi.
This patch renames a label for i2c_ak8975 to i2c9.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds missing pinctrls for I2C controllers 2-7.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Keystone supports dma-coherent on USB master and also needs
dma-ranges to specify the hardware alias memory range in which DMA
can be operational.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The dma-ranges property has to be specified per bus and has format:
< DMA addr > - Base DMA address for Bus (Bus format 32-bits)
< CPU addr > - Corresponding base CPU address (CPU format 64-bits)
< DMA range size > - Size of supported DMA range
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
SPI nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding any child
nodes to the SPI bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/spi@21000400/n25q128a11@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/spi@21000400/n25q128a11@0
Hence, ensure that all SPIx nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
I2C devices are not the part of Keystone SoC and have to be
defined in board DTS files.
Hence, move i2c0 EEPROM device node from Keystone SoC to
k2hk, k2e, k2l EVM files as they all have similar EEPROM SoCs
installed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
I2C nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding child
nodes to the I2C bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/i2c@2530800/pca@20
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/i2c@2530800/pca@20
Hence, ensure that all i2cX nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
this patch fills the resets properity for dspif, gps and dsp nodes.
these nodes belong to GPS related modules.
Signed-off-by: Tao Huang <Tao.Huang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
add cortex-a9-pmu node to make the performance monitor unit work on atlas6.
Signed-off-by: Ye He <Ye.He@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
in drivers/spi/spi-sirf.c, we have moved to use generic dma dt-binding.
here the dts should be changed too.
Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
The tsadcc node is useless as it doesn't refer to anything and the touchscreen
is handled by the adc0 node.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Move at91sam9rl SoC to the new main/slow clock model.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define crystal properties of sama5d3 xplained board.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define crystal frequencies of sama5d3xcm boards.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Replace the old main and clk definitions (fixed rate clk) by the new main and
slow clk subtree definition (ck = mux(rc_osc, osc)).
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
add pin groups for USP0 only holding one of TX and RX frame sync. this patch
matches with the change in drivers/pinctrl/sirf.
commit 73f68c01f4 did this for prima2, but missed prima2. this patch fixes
the problem.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Use MATRIX_KEY macro from dt-bindings/input/input.h
to make the keyboard matrix human readable.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These add device tree entry for qspi controller driver on dra7-evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VTT regulator for DDR3 termination on the am335x-evmsk is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The VTT regulator for DDR3 termination on the am437x-gp-evm is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add touchscreen support for AM437x GP EVM using pixcir
touchscreen controller.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixup Y resolution and add default pin state. Also update
the compatible id.
CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA722 is part of DRA72x family which are single core cortex A15 devices
with most infrastructure IPs otherwise same as whats on the DRA74x family.
So move the cpu nodes into dra74x.dtsi and dra72x.dtsi respectively.
Also add a minimal dra72-evm dts file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: linux-doc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: Tony Lindgren <tony@atomide.com>
"ti,dra752" is neither documented nor correct, since the device is actually a
dra742 device as rightly documented in dt bindings.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support of AW-NH387 (mwifiex) WiFi/BT chip connected to MMC3.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for CM-T54 CoM and SBC-T54 board:
http://compulab.co.il/products/computer-on-modules/cm-t54/http://compulab.co.il/products/sbcs/sbc-t54/
SBC-T54 is a single board computer based on OMAP5432 CPU.
It is implemented with a CM-T54 CoM providing most of the functions,
and SB-T54 carrier board providing connectors and several additional
functions.
Added basic support for:
* PMIC
* LED
* MMC/SD
* eMMC
* USB
* I2C1/4
* SB-T54 and CM-T54 EEPROMs
* RTC
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Expose the PMU on OMAP5.
Tested with perf on OMAP5 uEVM.
Signed-off-by: Nathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The N950/N9 uses two additional regulators from the twl 4030 for CSI-2
receiver (vaux2) and cameras (vaux3).
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for the Nokia N900's sound
system.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add madc node to twl4030, so that board DTS
files can simply reference the A/D converter.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree support for the wireless chip
built into the Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable
- USB PHY
- USB
for am43x-epos-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable
- USB PHY
- USB
for am437x-gp-evm
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add nodes for 2 instances each of
- ocp2scp
- USB PHY control module
- USB PHY
- dwc3_omap
- USB
for AM43xx.
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add USB and USB PHY reference clock data
Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: tabified]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Venice2 can detect write-protect on the SD card. Add the required
DT entries to allow this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[swarren: fixed GPIO polarity per Thierry's testing]
Tested-by: Thierry Reding <treding@nvidia.com>
With ARCH_OMAP2PLUS being separated out into OMAP2/3/4/5 etc all the TI device
tree blobs are built no matter the combination of SoCs that are enabled. This
often causes a bunch of irrelevant .dts to be built on a multi platform kernel,
this enables the building of just the ones relevant to the SoCs that are
actually enabled. It also orders the dts file alphabetically.
This also helps to avoid trivial merge conflicts when adding support
for new boards.
[tony@atomide.com: updated the order for am335x and am43x, moved am3517 to omap3]
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Use generic node names
- Fix up some weird formatting and white spaces
- Update copyright info
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
The mpu_clk, main_clk, and dbg_base_clk outputs from the main PLL go through a
pre-divider. Update socfpga.dtsi to represent those dividers for these
clocks.
Re-use the "div-reg" property that was used for the socfpga-gate-clock as this
is the same thing. Also update the documentation.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Add the necessary #reset-cells property to the rst-mgr node and
provide a header-file with all possible resets specified.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The timers and uart can get their clock frequencies using the common clock
driver.
Reviewed-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The Altera Cyclone5 and Arria5 devkit has an EEPROM and a RTC on the
board. This patch adds support for them.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
---
v2: Remove LCD as the driver has not been upstreamed.
Convert all socfpga DT files to the dtc preprocessor include syntax.
This allows to include header files in the devicetrees like other
SoC-types already do.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The SOCrates has an M41T82M RTC on i2c0. Add it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The SOCrates is a SOCFpga-Cyclone5 based board from EBV.
Add support for it.
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Add both can controllers to the dtsi.
Reviewed-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The first interrupt is not at 180 but 104. Fix it.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
The CubieTruck has an AMPAK AP6210 WiFi+Bluetooth module. The WiFi
part is a BCM43362 IC connected to MMC3 in the A20 SoC via SDIO.
The IC also takes a power enable signal via GPIO.
The WiFi module supports out-of-band interrupt signaling via GPIO,
but this is not supported in this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- more support for at91sam9rl and its associated EK board
- some improvements to at91sam9g45 (ADC, TS, PWM leds)
- addition of some missing pieces for describing audio
of SAMA5D3-EK in DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTUaATAAoJEAf03oE53VmQ48oH/3T2Uj8MY6J3gtFkBgys1IrQ
ZfOMEscf4wDoyoYKTyifu1iRr0KLCxdaS1BUtimzgOkDPZj3aHoK97uoIn+NWUZt
hJTSGPDh3neMAMT8W5/dqIXY5Fwt9qWjJygWCtzh+TLGDZPdnkdLMblRCX8w6Y/T
dZDEtbfcpGD+N4BqOrbEO49wKHdUAtetvF3FTxu5+2GcbO/n1Hn3K28F4m+7mmBe
9NFw1Su5xHXEIjCaKJUO4BZDS7QQXjR2afbYSr/JAZ/x1ij8Rz3OZ+RWrE7JqvPf
+VidFo6oLnOgp9FbkDxAbPbC6mWiFz1PGDsrFjR8GlvJpEzgBpme4WcN4o6bXko=
=3kLo
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
Merge "at91: DT for 3.16 #1" from Nicolas Ferre:
3.16: first DT series:
- more support for at91sam9rl and its associated EK board
- some improvements to at91sam9g45 (ADC, TS, PWM leds)
- addition of some missing pieces for describing audio
of SAMA5D3-EK in DT
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: sama5d3: clock for ssc from rk pin
ARM: at91: sama5d3: add the missing property
ARM: at91: sama5d3: correct the sound compatible string
ARM: at91: sama5d3: disable sound by default
ARM: at91: sama5d3: add DMA property for SSC devices
ARM: at91/dt: at91sam9m10g45ek PWM leds polarity is inversed
ARM: at91/dt: at91sam9m10g45ek: add ADC and touchscreen support
ARM: at91/dt: sam9g45: improve ADC/touchscreen support
ARM: at91/dt: add peripherals to the at91sam9rlek board
ARM: at91/dt: sam9rl: add lcd, adc, usb gadget and pwm support
Signed-off-by: Olof Johansson <olof@lixom.net>
The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add nodes for the 4 mmc controllers found on A20 SoCs to
arch/arm/boot/dts/sun7i-a20.dtsi.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a new sun6i-a31-m9 dts file for the Mele M9 / Mele A1000G Quad. These
HTPCs use the same board in a different case, for more details see:
http://linux-sunxi.org/Mele_M9
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add nodes for the 4 mmc controllers found on A31 SoCs to
arch/arm/boot/dts/sun6i-a31.dtsi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cd pin settings have been taken from the original firmware fex files,
and have been confirmed to work on the actual boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add nodes for the 3 mmc controllers found on A10s SoCs and for the 2 mmc
controllers found on A13 SoCs.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested on a subset of these boards, for the others boards the settings match
the ones of the tested boards according to the original firmware fex files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc0 is the only controller actually being used on boards, so limit the
pin-muxing options to that.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add nodes for the 4 mmc controllers found on A10 SoCs to
arch/arm/boot/dts/sun4i-a10.dtsi.
Signed-off-by: David Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sound node is missing a #sound-dai-cells property. Add it, so that
the sounds node can be used in combination with the simple-audio-card
binding.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1399141819-23924-5-git-send-email-andrew@lunn.ch
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ethernet PHYs found on Globalscale Guruplug are connected by RGMII-ID.
Set the corresponding phy-connection-type property accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-16-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Ethernet PHY compatible shall be "ethernet-phy-ieee802.3-c22" and
"ethernet-phy-idAAAA.BBBB" if PHY OUI id is known. We know it for
the PHY found on Guruplug, so set it accordingly.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-15-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently, the only 6282-based Kirkwood boards that use I2C1 are Openblocks
A6/A7. Both use the same default I2C1 pinctrl setting from kirkwood-6282.dtsi.
Move the pinctrl setting to the I2C1 node directly and put a note in front of
the corresponding pinctrl node to overwrite the setting on board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-14-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is only one valid pinctrl setting for I2C0 on Kirkwood. Now that we
have the setting in the common SoC pinctrl, move it to the I2C0 controller
node directly and remove it from the individual boards.
While at it, also fix up status = "okay" to "ok" on one board's I2C0 node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-13-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
There is only one valid pinctrl setting for NAND on Kirkwood. Now that we
have the setting in the common SoC pinctrl, move it to the NAND controller
node directly and remove it from the individual boards.
While at it, also fix up status = "okay" to "ok" on one board's NAND node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-12-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most Kirkwood boards use the default SPI0 pinctrl setting anyway. Add a
default pinctrl setting to the toplevel SoC SPI0 node and put a note
in front of the corresponding pinctrl node to overwrite the setting
on board level.
Currently, only T5325 is using a different setting and already
overwrites the corresponding pinctrl node.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-11-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most boards use the default UART0/1 pinctrl setting without RTS/CTS.
Add the pinctrl setting to the toplevel SoC UART nodes and put a note
in front of the corresponding pinctrl node to overwrite the setting
on board level. Currently, both boards using a different UART pinctrl
setting (Openblocks A6, A7) already overwrite the pinctrl node.
While at it, also fix up some status = "ok" to "okay" and again
whitespace issues on mplcec4 uart nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-10-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
On Kirkwood, there is only one valid pinctrl setting for GBE1. With
a common SoC pinctrl node, we can now set it in the node instead of
in each board file.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-9-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
All SoCs have the same pinctrl setting for NAND, UART0/1, SPI, TWSI0,
and GBE1. Move it to the common pinctrl node that we now have.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-8-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
All Kirkwood SoCs have their pinctrl registers at the same address.
Instead of replaying the same reg property on each SoC, have the
reg property set in the common SoC file already. This also allows
us to move common pinctrl settings to this node later on.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-7-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
To prepare pin-controller consolidation, first rename all pinctrl nodes
to a more appropriate name regarding ePAPR recommended names.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-6-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
UART devices found on Kirkwood SoCs derive their baudrate from TCLK.
With proper clocks property in the SoCs serial node, boards do not
need to overwrite it anymore.
Remove the remaining clock-frequency property from all Kirkwood boards.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-5-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
ePAPR allows to reference the device used for console output by
stdout-path property. With node labels for Kirkwood UART0, now
reference it on all Kirkwood boards that already have ttyS0 in
their bootargs property.
While at it, fix some whitespace issues on mplcec4's chosen node
(there are more, but we only fix the chosen node now)
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-4-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This adds missing node labels to Kirkwood common and SoC specific nodes
to allow to reference them more easily.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lkml.kernel.org/r/1398862602-29595-3-git-send-email-sebastian.hesselbarth@gmail.com
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Tegra Note 7 is a consumer tablet embedding a Tegra 4 SoC with 1GB RAM
and a 720p panel.
The following hardware is enabled by this device tree: UART, eMMC, USB
(needs external power), PMIC, backlight, DSI panel, keys.
SD card, HDMI, charger, self-powered USB, audio, wifi, bluetooth are not
yet supported but might be by future patches (likely in that order).
Touch panel, sensors & cameras will probably never be supported.
Pinctrl is not set yet, as the bootloader-provided values allow us to
use the currently supported hardware.
Initrd addresses are hardcoded to match the static values used by the
bootloader, since it won't add them for us. All the same, a kernel
command-line is provided to replace the one passed by the bootloader
which is filled with garbage.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
[treding@nvidia.com: DT fixes, DSI panel support]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
When creating the initial device tree for the Henninger board, I've overlooked
that EXTAL frequency needs to be overridden there. The 'sh-sci' driver managed
to work somehow but the SDHI driver that I've tried to enable just hanged with
the default EXTAL frequency of 0...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Like other imx SoCs only one USB clock is needed on mx35.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Like other imx SoCs only one USB clock is needed on mx25.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The kernel was not able to boot from SD card because sdhc support
was not present into the dts.
A new entry for sdhc1 was added for vf610-twr board based on the
compatible entry present on imx53.
After applying these changes, the kernel is able to boot successfully
from SD card.
Signed-off-by: Cosmin Stoica <cosminstefan.stoica@freescale.com>
Signed-off-by: Chircu Bogdan <Bogdan.Chircu@freescale.com>
Signed-off-by: Eddy Petrisor <eddy.petrisor@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO4_8 is connected to the Ethernet PHY reset line, so populate the
'phy-reset-gpios' property accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO2_3 controls the power to the Ethernet PHY, so provide a regulator node
for this.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Instead of relying on the bootloader for configuring the FEC pins, pass the
FEC pin configuration via device tree instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
UART1 is the console port on mx25pdk board.
Add the pin configuration for UART1 port and also pass 'fsl,uart-has-rtscts'
to indicate that the port has RTS and CTS pins.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Make the red gpio led available to the user.
This can be toggled with the sysfs for example, or used as a heartbeat or mmc
activity light by changing the trigger.
Signed-off-by: Vincent Stehlé <vincent.stehle@freescale.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds pin group for Synchronous Serial Interface 1 (SSI1)
for PCM-038 module and enables this interface. This change do nothing
at the current stage but helps to continue develop sound support.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add alias for FEC ethernet on i.MX to allow bootloaders (like U-Boot)
patch-in the MAC address for FEC using this alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Jetson TK1 can detect write-protect on the SD card. Add the required
DT entries to allow this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
This branch contains a pair of important bug fixes for the DT code:
- Fix some incorrect binding property names before they enter common usage
- Fix bug where some platform devices will be unable to get their
interrupt number when they depend on an interrupt controller that is
not available at device creation time. This is a problem causing
mainline to fail on a number of ARM platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTXr8WAAoJEMWQL496c2LNhzgP/RhhIS9ySzJkdPEMksnBaQbN
JKG+wBwlzvtJSPw2xX5EpWweOd1PDqHxLjjWu7q5WIrQQyOGRAELkYg1H+5ksFo1
obCAFOjTC7VXPGc+BX0dLN6Eq4UHP8k3Ui8zlMSZQNt+gBvYo1gX2ulR8sQgS8rF
xw+8iNDA2GIFusQbci35yOAhp6yo/ble3KIeR5dFKeMpiVSh9rqdLS+H9HgnG5Sw
G2LUrAeRY2yQbow3c1001HiKrJieZZSTCq8oiZDgJZY5+Qk8zamyj2xxgMoJUA8Q
2Kcb3379vNvDgjYX61NiwyrhIbJEiao8IXq6WMDNbmH3+FUwogrnh/A/g5POtX0N
JV5tGkc/2lfm5oBCFSzcw661XjLysPsm3nPLhnxRL/dlBVkl0IZzTVYPTqUtoKlK
NfwKFUDgg+QVmhFQT0BDCyOGAcRsz4rNEPPB6M12OmEKgxGpetfUaFdBcJqSNaxf
Ac6AAZCXrkLlRNOVhK333ILPxv1JRC++JAeRKNwHr9e6j2aJjUgilSuzpHJ5Lkyo
sj6kp+n1n+giYlgc9GjM7b33tm8XEd4rbcgwCWwaypEsl4FIwPs9xMys7md8SOCE
AAnVPVUvLGC9O2GhldeQlOgtGWzILW3zJXb2mrMIIGyLBGBx1qr3VJIZpxoddTc0
UtIJn0X37mKY/R4/hWs4
=B2JT
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree bug fixes from Grant Likely:
"These are some important bug fixes that need to get into v3.15.
This branch contains a pair of important bug fixes for the DT code:
- Fix some incorrect binding property names before they enter common
usage
- Fix bug where some platform devices will be unable to get their
interrupt number when they depend on an interrupt controller that
is not available at device creation time. This is a problem
causing mainline to fail on a number of ARM platforms"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
of/irq: do irq resolution in platform_get_irq
of: selftest: add deferred probe interrupt test
dt: Fix binding typos in clock-names and interrupt-names
This adds pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds pin-muxing info for the mmc controller / port combinations which
are known to be used on actual boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the PWM for both PWM channels on the cubietruck. They can be found on
connector CN8.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the PWM bindings for the Allwinner A20.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the PWM bindings for the Allwinner A10.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the pinctrl descriptions for both PWM channels of the Allwinner A20.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the pinctrl descriptions for both PWM channels of the Allwinner A10.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the performance monitoring unit found in the A31 SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Enable the performance monitoring unit found in the A20 SoCs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Jetson TK1 contains an RT5639 not an RT5640. While the two are extremely
similar and mostly compatible, we should still use the correct device
name in the device tree. I had meant to fix this before applying the
initial DT, but this issue slipped my mind.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The 1.2V supply for CSI and DSI was previously marked always-on. This is
suboptimal because it prevents the supply from being disabled when there
is no activity in the display or capture paths that it powers.
Hook up the regulator to the DSI output and mark it as not always-on, so
that it will only be enabled when DSI actually needs it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
