In order to reach the frequencies needed to output at 594MHz, the
firmware needs to be configured with the appropriate parameters in the
config.txt file (enable_hdmi_4kp60 and force_turbo).
Let's detect it at bind time, warn the user if we can't, and filter out
the relevant modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-10-maxime@cerno.tech
The BVB clock rate computation doesn't take into account a mode clock of
594MHz that we're going to need to support 4k60.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-9-maxime@cerno.tech
We'll need to have the HVS binding before the HDMI controllers so that
we can check whether the firmware allows to run in 4kp60. Reorder a bit
the component list, and document the current constraints we're aware of.
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-8-maxime@cerno.tech
Since we fixed the hooks to disable the encoder at boot, we now have an
unbalanced clk_disable call at boot since we never enabled them in the
first place.
Let's mimic the state of the hardware and enable the clocks at boot if
the controller is enabled to get the use-count right.
Cc: <stable@vger.kernel.org> # v5.10+
Fixes: 09c438139b ("drm/vc4: hdmi: Implement finer-grained hooks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-7-maxime@cerno.tech
At boot, we can't rely on the vc4_get_crtc_encoder since we don't have a
state yet and thus will not be able to figure out which connector is
attached to our CRTC.
However, we have a muxing bit in the CRTC register we can use to get the
encoder currently connected to the pixelvalve. We can thus read that
register, lookup the associated register through the vc4_pv_data
structure, and then pass it to vc4_crtc_disable so that we can perform
the proper operations.
Fixes: 875a4d5368 ("drm/vc4: drv: Disable the CRTC at boot time")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-6-maxime@cerno.tech
The vc4_get_crtc_encoder function currently only works when the
connector->state->crtc pointer is set, which is only true when the
connector is currently enabled.
However, we use it as part of the disable path as well, and our lookup
will fail in that case, resulting in it returning a null pointer we
can't act on.
We can access the connector that used to be connected to that crtc
though using the old connector state in the disable path.
Since we want to support both the enable and disable path, we can
support it by passing the state accessor variant as a function pointer,
together with the atomic state.
Fixes: 792c3132bc ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-5-maxime@cerno.tech
The vc4_crtc_config_pv will need to access the drm_atomic_state
structure and its only parent function, vc4_crtc_atomic_enable already
has access to it. Let's pass it as a parameter.
Fixes: 792c3132bc ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-4-maxime@cerno.tech
The vc4_set_crtc_possible_masks is meant to run over all the encoders
and then set their possible_crtcs mask to their associated pixelvalve.
However, since the commit 39fcb28083 ("drm/vc4: txp: Turn the TXP into
a CRTC of its own"), the TXP has been turned to a CRTC and encoder of
its own, and while it does indeed register an encoder, it no longer has
an associated pixelvalve. The code will thus run over the TXP encoder
and set a bogus possible_crtcs mask, overriding the one set in the TXP
bind function.
In order to fix this, let's skip any virtual encoder.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb28083 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-3-maxime@cerno.tech
The current code does a binary OR on the possible_crtcs variable of the
TXP encoder, while we want to set it to that value instead.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb28083 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-2-maxime@cerno.tech
The VEC's DAC on BCM2711 is slightly different compared to the one on
BCM283x and needs different configuration. In particular, bit 3
(mask 0x8) switches the BCM2711 DAC input to "self-test input data",
which makes the output unusable. Separating two compatible variants in
devicetrees and the DRM driver was therefore necessary.
The configurations used for both variants have been borrowed from
Raspberry Pi (model 3B for BCM283x, 4B for BCM2711) firmware defaults.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520150344.273900-4-maxime@cerno.tech
On the BCM2711 (Raspberry Pi 4), the VEC is actually connected to
output 2 of pixelvalve3.
NOTE: This contradicts the Broadcom docs, but has been empirically
tested and confirmed by Raspberry Pi firmware devs.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520150344.273900-2-maxime@cerno.tech
UAPI Changes:
* drm: Disable connector force-probing for non-master clients
* drm: Enforce consistency between IN_FORMATS property and cap + related
driver cleanups
* drm/amdgpu: Track devices, process info and fence info via
/proc/<pid>/fdinfo
* drm/ioctl: Mark AGP-related ioctls as legacy
* drm/ttm: Provide tt_shrink file to trigger shrinker via debugfs;
Cross-subsystem Changes:
* fbdev/efifb: Special handling of non-PCI devices
* fbdev/imxfb: Fix error message
Core Changes:
* drm: Add connector helper to attach HDR-metadata property and convert
drivers
* drm: Add connector helper to compare HDR-metadata and convert drivers
* drm: Add conenctor helper to attach colorspace property
* drm: Signal colorimetry in HDMI infoframe
* drm: Support pitch for destination buffers; Add blitter function
with generic format conversion
* drm: Remove struct drm_device.pdev and update legacy drivers
* drm: Remove obsolete DRM_KMS_FB_HELPER config option in core and drivers
* drm: Remove obsolete drm_pci_alloc/drm_pci_free
* drm/aperture: Add helpers for aperture ownership and convert drivers, replaces rsp fbdev helpers
* drm/agp: Mark DRM AGP code as legacy and convert legacy drivers
* drm/atomic-helpers: Cleanups
* drm/dp: Handle downstream port counts of 0 correctly; AUX channel fixes; Use
drm_err_*/drm_dbg_*(); Cleanups
* drm/dp_dual_mode: Use drm_err_*/drm_dbg_*()
* drm/dp_mst: Use drm_err_*/drm_dbg_*(); Use Extended Base Receiver Capability DPCD space
* drm/gem-ttm-helper: Provide helper for dumb_map_offset and convert drivers
* drm/panel: Use sysfs_emit; panel-simple: Use runtime PM, Power up panel
when reading EDID, Cache EDID, Cleanups;
Lms397KF04: DT bindings
* drm/pci: Mark AGP helpers as legacy
* drm/print: Handle NULL for DRM devices gracefully
* drm/scheduler: Change scheduled fence track
* drm/ttm: Don't count SG BOs against pages_limit; Warn about freeing pinned
BOs; Fix error handling if no BO can be swapped out; Move special
handling of non-GEM drivers into vmwgfx; Move page_alignment into
the BO; Set drm-misc as TTM tree in MAINTAINERS; Cleanup
ttm_agp_backend; Add ttm_sys_manager for system domain; Cleanups
Driver Changes:
* drm: Don't set allow_fb_modifiers explictly in drivers
* drm/amdgpu: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages
* drm/ast: Use managed pcim_iomap(); Fix EDID retrieval with DP501
* drm/bridge: MHDP8546: HDCP support + DT bindings, Register DP AUX channel
with userspace; Sil8620: Fix module dependencies; dw-hdmi: Add option to
not load CEC driver; Fix stopping in drm_bridge_chain_pre_enable();
Ti-sn65dsi86: Fix refclk handling, Break GPIO and MIPI-to-eDP into
subdrivers, Use pm_runtime autosuspend, cleanups; It66121: Add
driver + DT bindings; Adv7511: Support I2S IEC958 encoding; Anx7625: fix
power-on delay; Nwi-dsi: Modesetting fixes; Cleanups
* drm/bochs: Support screen blanking
* drm/gma500: Cleanups
* drm/gud: Cleanups
* drm/i915: Use correct max source link rate for MST
* drm/kmb: Cleanups
* drm/meson: Disable dw-hdmi CEC driver
* drm/nouveau: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages; Register AUX adapters after their connectors
* drm/qxl: Fix shadow BO unpin
* drm/radeon: Duplicate some DRM AGP code to uncouple from legacy drivers
* drm/simpledrm: Add a generic DRM driver for simple-framebuffer devices
* drm/tiny: Fix log spam if probe function gets deferred
* drm/vc4: Add support for HDR-metadata property; Cleanups
* drm/virtio: Create dumb BOs as guest blobs;
* drm/vkms: Use managed drmm_universal_plane_alloc(); Add XRGB plane
composition; Add overlay support
* drm/vmwgfx: Enable console with DRM_FBDEV_EMULATION; Fix CPU updates
of coherent multisample surfaces; Remove reservation semaphore; Add
initial SVGA3 support; Support amd64; Use 1-based IDR; Use min_t();
Cleanups
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAmCb4QsACgkQaA3BHVML
eiPwUgf/eTodvGQyB0cjv1vyHlttLo2t9k4QBO0pzVH0DJokl/pMpY0CuS8A/afW
RmKLYod3TQb2QeEqWjocPxcYrh5WCbjdDZlmSb+pF+qau4b4s09SzIogK3lO1Nve
9N1WVa7C3JC3k3XYexpeZ78RtoNN0UboMKDfbZODnn1PtjVtOp7Nbb92trRuB7y+
B72A8RQMYB5IywVln9+lzLYcrmpHZbk/sLmC5pIGBPcTyhn0TFinUYlg9iq1PvNM
fIqvPvXwxDVRO6hgnxZWKrdvQKCOcl5KFnk4E6H+ZkgWJ+yuAWI9r2N9TeelcW+M
jlCHreWEHhuTPkr/ypnVmO8kuEgSFA==
=G9ip
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-05-12' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.14:
UAPI Changes:
* drm: Disable connector force-probing for non-master clients
* drm: Enforce consistency between IN_FORMATS property and cap + related
driver cleanups
* drm/amdgpu: Track devices, process info and fence info via
/proc/<pid>/fdinfo
* drm/ioctl: Mark AGP-related ioctls as legacy
* drm/ttm: Provide tt_shrink file to trigger shrinker via debugfs;
Cross-subsystem Changes:
* fbdev/efifb: Special handling of non-PCI devices
* fbdev/imxfb: Fix error message
Core Changes:
* drm: Add connector helper to attach HDR-metadata property and convert
drivers
* drm: Add connector helper to compare HDR-metadata and convert drivers
* drm: Add conenctor helper to attach colorspace property
* drm: Signal colorimetry in HDMI infoframe
* drm: Support pitch for destination buffers; Add blitter function
with generic format conversion
* drm: Remove struct drm_device.pdev and update legacy drivers
* drm: Remove obsolete DRM_KMS_FB_HELPER config option in core and drivers
* drm: Remove obsolete drm_pci_alloc/drm_pci_free
* drm/aperture: Add helpers for aperture ownership and convert drivers, replaces rsp fbdev helpers
* drm/agp: Mark DRM AGP code as legacy and convert legacy drivers
* drm/atomic-helpers: Cleanups
* drm/dp: Handle downstream port counts of 0 correctly; AUX channel fixes; Use
drm_err_*/drm_dbg_*(); Cleanups
* drm/dp_dual_mode: Use drm_err_*/drm_dbg_*()
* drm/dp_mst: Use drm_err_*/drm_dbg_*(); Use Extended Base Receiver Capability DPCD space
* drm/gem-ttm-helper: Provide helper for dumb_map_offset and convert drivers
* drm/panel: Use sysfs_emit; panel-simple: Use runtime PM, Power up panel
when reading EDID, Cache EDID, Cleanups;
Lms397KF04: DT bindings
* drm/pci: Mark AGP helpers as legacy
* drm/print: Handle NULL for DRM devices gracefully
* drm/scheduler: Change scheduled fence track
* drm/ttm: Don't count SG BOs against pages_limit; Warn about freeing pinned
BOs; Fix error handling if no BO can be swapped out; Move special
handling of non-GEM drivers into vmwgfx; Move page_alignment into
the BO; Set drm-misc as TTM tree in MAINTAINERS; Cleanup
ttm_agp_backend; Add ttm_sys_manager for system domain; Cleanups
Driver Changes:
* drm: Don't set allow_fb_modifiers explictly in drivers
* drm/amdgpu: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages
* drm/ast: Use managed pcim_iomap(); Fix EDID retrieval with DP501
* drm/bridge: MHDP8546: HDCP support + DT bindings, Register DP AUX channel
with userspace; Sil8620: Fix module dependencies; dw-hdmi: Add option to
not load CEC driver; Fix stopping in drm_bridge_chain_pre_enable();
Ti-sn65dsi86: Fix refclk handling, Break GPIO and MIPI-to-eDP into
subdrivers, Use pm_runtime autosuspend, cleanups; It66121: Add
driver + DT bindings; Adv7511: Support I2S IEC958 encoding; Anx7625: fix
power-on delay; Nwi-dsi: Modesetting fixes; Cleanups
* drm/bochs: Support screen blanking
* drm/gma500: Cleanups
* drm/gud: Cleanups
* drm/i915: Use correct max source link rate for MST
* drm/kmb: Cleanups
* drm/meson: Disable dw-hdmi CEC driver
* drm/nouveau: Pin/unpin fixes wrt to TTM; Use bo->base.size instead of
mem->num_pages; Register AUX adapters after their connectors
* drm/qxl: Fix shadow BO unpin
* drm/radeon: Duplicate some DRM AGP code to uncouple from legacy drivers
* drm/simpledrm: Add a generic DRM driver for simple-framebuffer devices
* drm/tiny: Fix log spam if probe function gets deferred
* drm/vc4: Add support for HDR-metadata property; Cleanups
* drm/virtio: Create dumb BOs as guest blobs;
* drm/vkms: Use managed drmm_universal_plane_alloc(); Add XRGB plane
composition; Add overlay support
* drm/vmwgfx: Enable console with DRM_FBDEV_EMULATION; Fix CPU updates
of coherent multisample surfaces; Remove reservation semaphore; Add
initial SVGA3 support; Support amd64; Use 1-based IDR; Use min_t();
Cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/YJvkD523evviED01@linux-uq9g.fritz.box
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210511092923.4617-1-thunder.leizhen@huawei.com
Our driver while supporting HDR didn't send the proper colorimetry info
in the AVI infoframe.
Let's add the property needed so that the userspace can let us know what
the colorspace is supposed to be.
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430094451.2145002-5-maxime@cerno.tech
Cppcheck complains that the declaration doesn't match the function
definition. Obviously "left" should come before "right". The caller
and the function implementation are done this way, it's just the
declaration which is wrong so this doesn't affect runtime.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/YH/720FD978TPhHp@mwanda
Since
commit 890880ddfd
Author: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Date: Fri Jan 4 09:56:10 2019 +0100
drm: Auto-set allow_fb_modifiers when given modifiers at plane init
this is done automatically as part of plane init, if drivers set the
modifier list correctly. Which is the case here.
Acked-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210413094904.3736372-11-daniel.vetter@ffwll.ch
msm-next pull request has a baseline with stuff from -fixes, roll
forward first.
Some simple conflicts in amdgpu, ttm and one in i915 where git gets
confused and tries to add the same function twice.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Experimentally have found PV on hvs4 reports fifo full
error with expected settings and does not with one less
This appears as:
[drm:drm_atomic_helper_wait_for_flip_done] *ERROR* [CRTC:82:crtc-3] flip_done timed out
with bit 10 of PV_STAT set "HVS driving pixels when the PV FIFO is full"
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318161328.1471556-3-maxime@cerno.tech
The vc4_plane_atomic_async_update function assigns twice in a row the
src_h field in the drm_plane_state structure to the same value. Remove
the second one.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210318161328.1471556-2-maxime@cerno.tech
The current atomic helpers have either their object state being passed as
an argument or the full atomic state.
The former is the pattern that was done at first, before switching to the
latter for new hooks or when it was needed.
Let's convert all the remaining helpers to provide a consistent
interface, starting with the planes atomic_check.
The conversion was done using the coccinelle script below plus some
manual changes for vmwgfx, built tested on all the drivers.
@@
identifier plane, plane_state;
symbol state;
@@
struct drm_plane_helper_funcs {
...
int (*atomic_check)(struct drm_plane *plane,
- struct drm_plane_state *plane_state);
+ struct drm_atomic_state *state);
...
}
@ plane_atomic_func @
identifier helpers;
identifier func;
@@
static const struct drm_plane_helper_funcs helpers = {
...,
.atomic_check = func,
...,
};
@@
struct drm_plane_helper_funcs *FUNCS;
identifier f;
identifier dev;
identifier plane, plane_state, state;
@@
f(struct drm_device *dev, struct drm_atomic_state *state)
{
<+...
- FUNCS->atomic_check(plane, plane_state)
+ FUNCS->atomic_check(plane, state)
...+>
}
@ ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
... when != new_plane_state
}
@ adds_new_state depends on plane_atomic_func && !ignores_new_state @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane, struct drm_plane_state *new_plane_state)
{
+ struct drm_plane_state *new_plane_state = drm_atomic_get_new_plane_state(state, plane);
...
}
@ depends on plane_atomic_func @
identifier plane_atomic_func.func;
identifier plane, new_plane_state;
@@
func(struct drm_plane *plane,
- struct drm_plane_state *new_plane_state
+ struct drm_atomic_state *state
)
{ ... }
@ include depends on adds_new_state @
@@
#include <drm/drm_atomic.h>
@ no_include depends on !include && adds_new_state @
@@
+ #include <drm/drm_atomic.h>
#include <drm/...>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210219120032.260676-4-maxime@cerno.tech
The function drm_gem_fb_prepare_fb() is a helper for atomic modesetting,
but currently located next to framebuffer helpers. Move it to GEM atomic
helpers, rename it slightly and adopt the drivers. Same for the rsp
simple-pipe helper.
Compile-tested with x86-64, aarch64 and arm. The patch is fairly large,
but there are no functional changes.
v3:
* remove out-comented line in drm_gem_framebuffer_helper.h
(Maxime)
v2:
* rename to drm_gem_plane_helper_prepare_fb() (Daniel)
* add tutorial-style documentation
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210222141756.7864-1-tzimmermann@suse.de
We introduced the BCM2711 support to the vc4 HDMI controller with 5.10,
but this was lacking any of the interrupts of the CEC controller so we
have to deal with the backward compatibility.
Do so by simply ignoring the CEC setup if the DT doesn't have the
interrupts property.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-13-maxime@cerno.tech
(cherry picked from commit 4d03ed7ad7)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Now that our HDMI controller supports CEC for the BCM2711, let's remove
that flag.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-12-maxime@cerno.tech
(cherry picked from commit f551863af9)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The HDMI controller found in the BCM2711 has an external interrupt
controller for the CEC and hotplug interrupt shared between the two
instances.
Let's add a variant flag to register a single interrupt handler and
deals with the interrupt handler setup, or two interrupt handlers
relying on an external irqchip.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-11-maxime@cerno.tech
(cherry picked from commit ad6380e9aa)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The BCM2711 has two different interrupt sources to transmit and receive
CEC messages, provided through an external interrupt chip shared between
the two HDMI interrupt controllers.
The rest of the CEC controller is identical though so we need to change
a bit the code organisation to share the code as much as possible, yet
still allowing to register independent handlers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-10-maxime@cerno.tech
(cherry picked from commit 0c38490a03)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
While the BCM2835 had the CEC clock derived from the HSM clock, the
BCM2711 has a dedicated parent clock for it.
Let's introduce a separate clock for it so that we can handle both
cases.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-9-maxime@cerno.tech
(cherry picked from commit cd7f016c93)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
As part of the enable sequence we might change the HSM clock rate if the
pixel rate is different than the one we were already dealing with.
On the BCM2835 however, the CEC clock derives from the HSM clock so any
rate change will need to be reflected in the CEC clock divider to output
40kHz.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-8-maxime@cerno.tech
(cherry picked from commit a9dd0b9a5c)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The CEC clock divider needs to output a frequency of 40kHz from the HSM
rate on the BCM2835. The driver used to have a fixed frequency for it,
but that changed for the BCM2711 and we now need to compute it
dynamically to maintain the proper rate.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-7-maxime@cerno.tech
(cherry picked from commit f1ceb9d100)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Currently we call cec_phys_addr_invalidate on a hotplug deassert.
That may be due to a TV power cycling, or an AVR being switched
on (and switching edid).
This makes CEC unusable since our controller wouldn't have a physical
address anymore.
Set it back up again on the hotplug assert.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-6-maxime@cerno.tech
(cherry picked from commit b06eecb515)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The commit 311e305fdb ("drm/vc4: hdmi: Implement a register layout
abstraction") forgot one CEC register, and made a copy and paste mistake
for another one. Fix those mistakes.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-5-maxime@cerno.tech
(cherry picked from commit 303085bc11)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The code prior to 311e305fdb ("drm/vc4: hdmi: Implement a register
layout abstraction") was relying on the fact that the register offset
was incremented by 4 for each readl call. That worked since the register
width is 4 bytes.
However, since that commit the HDMI_READ macro is now taking an enum,
and the offset doesn't increment by 4 but 1 now. Divide the index by 4
to fix this.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-4-maxime@cerno.tech
(cherry picked from commit e9c9481f37)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The hdmi reset got moved to a later point in the commit 9045e91a47
("drm/vc4: hdmi: Add reset callback").
However, the reset now occurs after vc4_hdmi_cec_init and so tramples
the setup of registers like HDMI_CEC_CNTRL_1
This only affects pi0-3 as on pi4 the cec registers are in a separate
block
Fixes: 9045e91a47 ("drm/vc4: hdmi: Add reset callback")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-3-maxime@cerno.tech
(cherry picked from commit 7155334f15)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Commit 0a038c1c29 ("drm/vc4: Move LBM creation out of
vc4_plane_mode_set()") changed the LBM allocation logic from first
allocating the LBM memory for the plane to running mode_set,
adding a gap in the LBM, and then running the dlist allocation filling
that gap.
The gap was introduced by incrementing the dlist array index, but was
never checking whether or not we were over the array length, leading
eventually to memory corruptions if we ever crossed this limit.
vc4_dlist_write had that logic though, and was reallocating a larger
dlist array when reaching the end of the buffer. Let's share the logic
between both functions.
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Eric Anholt <eric@anholt.net>
Fixes: 0a038c1c29 ("drm/vc4: Move LBM creation out of vc4_plane_mode_set()")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210129160647.128373-1-maxime@cerno.tech
We introduced the BCM2711 support to the vc4 HDMI controller with 5.10,
but this was lacking any of the interrupts of the CEC controller so we
have to deal with the backward compatibility.
Do so by simply ignoring the CEC setup if the DT doesn't have the
interrupts property.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-13-maxime@cerno.tech
Now that our HDMI controller supports CEC for the BCM2711, let's remove
that flag.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-12-maxime@cerno.tech
The HDMI controller found in the BCM2711 has an external interrupt
controller for the CEC and hotplug interrupt shared between the two
instances.
Let's add a variant flag to register a single interrupt handler and
deals with the interrupt handler setup, or two interrupt handlers
relying on an external irqchip.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-11-maxime@cerno.tech
The BCM2711 has two different interrupt sources to transmit and receive
CEC messages, provided through an external interrupt chip shared between
the two HDMI interrupt controllers.
The rest of the CEC controller is identical though so we need to change
a bit the code organisation to share the code as much as possible, yet
still allowing to register independent handlers.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-10-maxime@cerno.tech
While the BCM2835 had the CEC clock derived from the HSM clock, the
BCM2711 has a dedicated parent clock for it.
Let's introduce a separate clock for it so that we can handle both
cases.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-9-maxime@cerno.tech
As part of the enable sequence we might change the HSM clock rate if the
pixel rate is different than the one we were already dealing with.
On the BCM2835 however, the CEC clock derives from the HSM clock so any
rate change will need to be reflected in the CEC clock divider to output
40kHz.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-8-maxime@cerno.tech
The CEC clock divider needs to output a frequency of 40kHz from the HSM
rate on the BCM2835. The driver used to have a fixed frequency for it,
but that changed for the BCM2711 and we now need to compute it
dynamically to maintain the proper rate.
Fixes: cd4cb49dc5 ("drm/vc4: hdmi: Adjust HSM clock rate depending on pixel rate")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-7-maxime@cerno.tech
Currently we call cec_phys_addr_invalidate on a hotplug deassert.
That may be due to a TV power cycling, or an AVR being switched
on (and switching edid).
This makes CEC unusable since our controller wouldn't have a physical
address anymore.
Set it back up again on the hotplug assert.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-6-maxime@cerno.tech
The commit 311e305fdb ("drm/vc4: hdmi: Implement a register layout
abstraction") forgot one CEC register, and made a copy and paste mistake
for another one. Fix those mistakes.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-5-maxime@cerno.tech
The code prior to 311e305fdb ("drm/vc4: hdmi: Implement a register
layout abstraction") was relying on the fact that the register offset
was incremented by 4 for each readl call. That worked since the register
width is 4 bytes.
However, since that commit the HDMI_READ macro is now taking an enum,
and the offset doesn't increment by 4 but 1 now. Divide the index by 4
to fix this.
Fixes: 311e305fdb ("drm/vc4: hdmi: Implement a register layout abstraction")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-4-maxime@cerno.tech
The hdmi reset got moved to a later point in the commit 9045e91a47
("drm/vc4: hdmi: Add reset callback").
However, the reset now occurs after vc4_hdmi_cec_init and so tramples
the setup of registers like HDMI_CEC_CNTRL_1
This only affects pi0-3 as on pi4 the cec registers are in a separate
block
Fixes: 9045e91a47 ("drm/vc4: hdmi: Add reset callback")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111142309.193441-3-maxime@cerno.tech
LBM base address is measured in units of pixels per cycle.
That is 4 for 2711 (hvs5) and 2 for 2708.
We are wasting 75% of lbm by indexing without the scaling.
But we were also using too high a size for the lbm resulting
in partial corruption (right hand side) of vertically
scaled images, usually at 4K or lower resolutions with more layers.
The physical RAM of LBM on 2711 is 8 * 1920 * 16 * 12-bit
(pixels are stored 12-bits per component regardless of format).
The LBM address indexes work in units of pixels per clock,
so for 4 pixels per clock that means we have 32 * 1920 = 60K
Fixes: c54619b0bf ("drm/vc4: Add support for the BCM2711 HVS5")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Tested-By: Lucas Nussbaum <lucas@debian.org>
Tested-By: Ryutaroh Matsumoto <ryutaroh@ict.e.titech.ac.jp>
Link: https://patchwork.freedesktop.org/patch/msgid/20210121105759.1262699-1-maxime@cerno.tech
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmAOFRIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG4lcH/jFAG+AXR6T2K3dG
adJmdAWQKdDj71Ruoyefx5GSbD0B+rM1UcxOQgmZem2127RJgfDBBVYyjSwh7H1F
LRJdN6+NKReL2OW/HMnufvpVMvWICTWHInyvsqKqp+Yo4GC5z46OtsmzSayYgTaP
v2G9auC/rSUlzmQux9EAbTKDeNGMum3dt2rfsmnIDymBSHoPbizXF93/2hoo9jwx
BZQCq0nYBCa9pEdsmgvqKkb/Y5+CSFoe02qdUZFIuwh6qd/XPfeDPSu4O3z4J9g6
x8G+f7doeU0nzsAP+K0lG7ulAygxRHm5Bn2rwVdlYfihAuPNyF+Ua3duxBvjOBEY
7w/UQ64=
=ZWS9
-----END PGP SIGNATURE-----
Merge tag 'v5.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux into drm-next
Backmerge v5.11-rc5 into drm-next to clean up a bunch of conflicts we are dragging around.
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's currently four users of the same logic to wait for a commit to
be flipped: three for the CRTCs, connectors and planes in
drm_atomic_helper_wait_for_dependencies, and one in vc4.
Let's consolidate this a bit to avoid any code duplication.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210111084401.117152-1-maxime@cerno.tech
User-space ALSA matches a card's driver name against an internal list of
aliases in order to select the correct configuration for the system.
When the driver name isn't defined, the match is performed against the
card's name.
With the introduction of RPi4 we now have two HDMI ports with two
distinct audio cards. This is reflected in their names, making them
different from previous RPi versions. With this, ALSA ultimately misses
the board's configuration on RPi4.
In order to avoid this, set "card->driver_name" to "vc4-hdmi"
unanimously.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Fixes: f437bc1ec7 ("drm/vc4: drv: Support BCM2711")
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210115191209.12852-1-nsaenzjulienne@suse.de
The function vc4_prime_import_sg_table() is an otherwise empty wrapper
around CMA's drm_gem_cma_prime_import_sg_table(). Removing it in favor
of the latter allows to initialize vc4_drm_driver with CMA's initializer
macro.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210114084949.29014-1-tzimmermann@suse.de
Moving vc4's mmap code from vc4_mmap() into a GEM object function
allows for the use drm_gem_mmap() and drm_gem_prime_mmap(). The content
of vc4_drm_fpos can then be generated by DEFINE_DRM_GEM_FOPS().
The actual mmap implementation is just a check if the BO is a validated
shader plus the default CMA mmap code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210108140808.25775-4-tzimmermann@suse.de
Use the drm_plane_cleanup() function directly as the drm_plane_funcs
.destroy() handler without creating an unnecessary wrapper around it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Unlike the previous generations, the HSM clock limitation is way above
what we can reach without scrambling, so let's move the maximum
frequency we support to the maximum clock frequency without scrambling.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-9-maxime@cerno.tech
The PHY initialisation parameters are not based on the pixel clock but
the TMDS clock rate which can be the pixel clock in the standard case,
but could be adjusted based on some parameters like the bits per color.
Since the TMDS clock rate is stored in our custom connector state
already, let's reuse it from there instead of computing it again.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-8-maxime@cerno.tech
The pixel rate is for now quite simple to compute, but with more features
(30 and 36 bits output, YUV output, etc.) will depend on a bunch of
connectors properties.
Let's store the rate we have to run the pixel clock at in our custom
connector state, and compute it in atomic_check.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-7-maxime@cerno.tech
When run with a higher bpc than 8, the clock of the HDMI controller needs
to be adjusted. Let's create a connector state that will be used at
atomic_check and atomic_enable to compute and store the clock rate
associated to the state.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-6-maxime@cerno.tech
drm_atomic_helper_connector_reset uses kmalloc which, from an API
standpoint, can fail, and thus setting connector->state to NULL.
However, our reset hook then calls drm_atomic_helper_connector_tv_reset
that will access connector->state without checking if it's a valid
pointer or not.
Make sure we don't end up accessing a NULL pointer.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-5-maxime@cerno.tech
Commit 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within
limits") was intended to compute the pixel rate to make sure we remain
within the boundaries of what the hardware can provide.
However, unlike what mode_valid was checking for, we forgot to take
into account the clock doubling flag that can be set for modes. Let's
honor that flag if it's there.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reported-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Fixes: 63495f6b4a ("drm/vc4: hdmi: Make sure our clock rate is within limits")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-4-maxime@cerno.tech
Since the CRTC setup in vc4 is split between the PixelValves/TXP and the
HVS, only the PV/TXP atomic hooks were updated in the previous commits, but
it makes sense to update the HVS ones too.
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215154243.540115-2-maxime@cerno.tech
To support legacy gamma ioctls the drivers need to set
drm_crtc_funcs.gamma_set either to a custom implementation or to
drm_atomic_helper_legacy_gamma_set. Most of the atomic drivers do the
latter.
We can simplify this by making the core handle it automatically.
Move the drm_atomic_helper_legacy_gamma_set() functionality into
drm_color_mgmt.c to make drm_mode_gamma_set_ioctl() use
drm_crtc_funcs.gamma_set if set or GAMMA_LUT property if not.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201211114237.213288-2-tomi.valkeinen@ti.com
Now that the semaphore is gone, our atomic_commit implementation is
basically drm_atomic_helper_commit with a somewhat custom commit_tail,
the main difference being that we're using wait_for_flip_done instead of
wait_for_vblanks used in the drm_atomic_helper_commit_tail helper.
Let's switch to using drm_atomic_helper_commit.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151138.1739736-8-maxime@cerno.tech
The HVS state now has both unassigned_channels that reflects the
channels that are not used in the associated state, and the in_use
boolean for each channel that says whether or not a particular channel
is in use.
Both express pretty much the same thing, and we need the in_use variable
to properly track the commits, so let's get rid of unassigned_channels.
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151138.1739736-6-maxime@cerno.tech
If we're having two subsequent, non-blocking, commits on two different
CRTCs that share no resources, there's no guarantee on the order of
execution of both commits.
However, the second one will consider the first one as the old state,
and will be in charge of freeing it once that second commit is done.
If the first commit happens after that second commit, it might access
some resources related to its state that has been freed, resulting in a
use-after-free bug.
The standard DRM objects are protected against this, but our HVS private
state isn't so let's make sure we wait for all the previous FIFO users
to finish their commit before going with our own.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201204151138.1739736-5-maxime@cerno.tech
Required backmerge since we will be based on top of v5.11, and there
has been a request to backmerge already to upstream some features.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
BCM2711 DSI1 doesn't have the issue with the ARM not being
able to write to the registers, therefore remove the DMA
workaround for that compatible string.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-8-maxime@cerno.tech
DSI0 was partially supported, but didn't register with the main
driver, and the code was inconsistent as to whether it checked
port == 0 or port == 1.
Add compatible string and other support to make it consistent.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-6-maxime@cerno.tech
Most of the differences between DSI0 and DSI1 are handled through the
ID. However, the BCM2711 DSI is going to introduce one more variable to
the mix and will break some expectations of the earlier, simpler, test.
Let's add a variant structure that will address most of the differences
between those three controllers.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-5-maxime@cerno.tech
The DSI clocks setup function has been using an array to store the clock
name of either the DSI0 or DSI1 blocks, using the port ID to choose the
proper one.
Let's switch to an snprintf call to do the same thing and simplify the
array a bit.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-4-maxime@cerno.tech
The DSI1_PHY_AFEC0_PD_DLANE1 and DSI1_PHY_AFEC0_PD_DLANE3 register
definitions were swapped, so trying to use more than a single data
lane failed as lane 1 would get powered down.
(In theory a 4 lane device would work as all lanes would remain
powered).
Correct the definitions.
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-3-maxime@cerno.tech
The infoframes are sent at a regular interval as a data island packet,
so we don't need to wait for them to be sent when we're setting them up.
However, we do need to poll when we're enabling since the we can't
update the packet RAM until it has been sent.
Let's add a boolean flag to tell whether we want to poll or not to
support both cases.
Suggested-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203074624.721559-1-maxime@cerno.tech
The new GEM object function drm_gem_cma_mmap() sets the VMA flags
and offset as in the old implementation and immediately maps in the
buffer's memory pages.
Changing CMA helpers to use the GEM object function allows for the
removal of the special implementations for mmap and gem_prime_mmap
callbacks. The regular functions drm_gem_mmap() and drm_gem_prime_mmap()
are now used.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201123115646.11004-3-tzimmermann@suse.de
The current HVS muxing code will consider the CRTCs in a given state to
setup their muxing in the HVS, and disable the other CRTCs muxes.
However, it's valid to only update a single CRTC with a state, and in this
situation we would mux out a CRTC that was enabled but left untouched by
the new state.
Fix this by setting a flag on the CRTC state when the muxing has been
changed, and only change the muxing configuration when that flag is there.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201120144245.398711-3-maxime@cerno.tech
If a CRTC is enabled but not active, and that we're then doing a page
flip on another CRTC, drm_atomic_get_crtc_state will bring the first
CRTC state into the global state, and will make us wait for its vblank
as well, even though that might never occur.
Instead of creating the list of the free channels each time atomic_check
is called, and calling drm_atomic_get_crtc_state to retrieve the
allocated channels, let's create a private state object in the main
atomic state, and use it to store the available channels.
Since vc4 has a semaphore (with a value of 1, so a lock) in its commit
implementation to serialize all the commits, even the nonblocking ones, we
are free from the use-after-free race if two subsequent commits are not ran
in their submission order.
Fixes: 87ebcd42fb ("drm/vc4: crtc: Assign output to channel automatically")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201120144245.398711-2-maxime@cerno.tech
There's cross-talk on the RPi4 between the 2.4GHz channels used by the WiFi
chip and some resolutions, most notably 1440p at 60Hz.
In such a case, we can either reject entirely the mode, or lower slightly
the pixel frequency to remove the overlap. Let's go for the latter.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029134018.1948636-2-maxime@cerno.tech
We've had a number of muxing corner-cases with specific ways to reproduce
them, so let's document them to make sure they aren't lost and introduce
regressions later on.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105135656.383350-6-maxime@cerno.tech
The code that assigns HVS channels during atomic_check is starting to grow
a bit big, let's move it into a separate function.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201105135656.383350-5-maxime@cerno.tech
