Pull block layer fixes from Jens Axboe:
"A final set of fixes for 4.3.
It is (again) bigger than I would have liked, but it's all been
through the testing mill and has been carefully reviewed by multiple
parties. Each fix is either a regression fix for this cycle, or is
marked stable. You can scold me at KS. The pull request contains:
- Three simple fixes for NVMe, fixing regressions since 4.3. From
Arnd, Christoph, and Keith.
- A single xen-blkfront fix from Cathy, fixing a NULL dereference if
an error is returned through the staste change callback.
- Fixup for some bad/sloppy code in nbd that got introduced earlier
in this cycle. From Markus Pargmann.
- A blk-mq tagset use-after-free fix from Junichi.
- A backing device lifetime fix from Tejun, fixing a crash.
- And finally, a set of regression/stable fixes for cgroup writeback
from Tejun"
* 'for-linus' of git://git.kernel.dk/linux-block:
writeback: remove broken rbtree_postorder_for_each_entry_safe() usage in cgwb_bdi_destroy()
NVMe: Fix memory leak on retried commands
block: don't release bdi while request_queue has live references
nvme: use an integer value to Linux errno values
blk-mq: fix use-after-free in blk_mq_free_tag_set()
nvme: fix 32-bit build warning
writeback: fix incorrect calculation of available memory for memcg domains
writeback: memcg dirty_throttle_control should be initialized with wb->memcg_completions
writeback: bdi_writeback iteration must not skip dying ones
writeback: fix bdi_writeback iteration in wakeup_dirtytime_writeback()
writeback: laptop_mode_timer_fn() needs rcu_read_lock() around bdi_writeback iteration
nbd: Add locking for tasks
xen-blkfront: check for null drvdata in blkback_changed (XenbusStateClosing)
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two KASAN fixes, two EFI boot fixes, two boot-delay
optimization fixes, and a fix for a IRQ handling hang observed on
virtual platforms"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm, kasan: Silence KASAN warnings in get_wchan()
compiler, atomics, kasan: Provide READ_ONCE_NOCHECK()
x86, kasan: Fix build failure on KASAN=y && KMEMCHECK=y kernels
x86/smpboot: Fix CPU #1 boot timeout
x86/smpboot: Fix cpu_init_udelay=10000 corner case boot parameter misbehavior
x86/ioapic: Disable interrupts when re-routing legacy IRQs
x86/setup: Extend low identity map to cover whole kernel range
x86/efi: Fix multiple GOP device support
This was found during userspace fuzzing test when a large size dma cma
allocation is made by driver(like ion) through userspace.
show_stack+0x10/0x1c
dump_stack+0x74/0xc8
kasan_report_error+0x2b0/0x408
kasan_report+0x34/0x40
__asan_storeN+0x15c/0x168
memset+0x20/0x44
__dma_alloc_coherent+0x114/0x18c
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWKEKdAAoJEEhZKYFQ1nG7dysH/jmFSatDJvgA7woliRZ7p0H/
elNu6AOjqBnsi23Vp54IOVWYTVIDhLsXxlzEOgO6XXfsI99TqFQIIS2VYSo6xues
Eq5hIxh5n9uue3VMnw9bxYHcFkFG9LDAlyMXecEayAB74UqnQLbo2bRDfnSopaf1
dEOq9mdT8llYbtVww6bVXtL78wgwxVk1gTfISllxgt7DEuYwgT+gQJCDLrmkGPn0
XfiaZWamNmDlQd4z/qqoG65+yNmZZMZQKtugCx4MoiBbHVclRN7j2eNsCZ0y6dsZ
qxs+CazL/IeYCqxRRXl5Fopraer1uJeOPeFgA+lRV6WPhMEe7eg6ojkDp/8Y18Y=
=Dh+g
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB Chipidea updates for v4.4-rc1
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jPoY
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.4 merge window
This pull request is large with a total of 136 non-merge
commits. Because of its size, we will only describe the big things in
broad terms.
Many will be happy to know that dwc3 is now almost twice as fast after
some profiling and speed improvements. Also in dwc3, John Youn from
Synopsys added support for their new DWC USB3.1 IP Core and the HAPS
platform which can be used to validate it.
A series of patches from Robert Baldyga cleaned up uses of
ep->driver_data as a flag for "claimed endpoint" in favor of the new
ep->claimed flag.
Sudip Mukherjee fixed a ton of really old problems on the amd5536udc
driver. That should make a few people happy.
Heikki Krogerus worked on converting dwc3 to the unified device property
interface.
Together with these, there's a ton of non-critical fixes, typos and
stuff like that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power mode
and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Some code may perform racy by design memory reads. This could be
harmless, yet such code may produce KASAN warnings.
To hide such accesses from KASAN this patch introduces
READ_ONCE_NOCHECK() macro. KASAN will not check the memory
accessed by READ_ONCE_NOCHECK(). The KernelThreadSanitizer
(KTSAN) is going to ignore it as well.
This patch creates __read_once_size_nocheck() a clone of
__read_once_size(). The only difference between them is
'no_sanitized_address' attribute appended to '*_nocheck'
function. This attribute tells the compiler that instrumentation
of memory accesses should not be applied to that function. We
declare it as static '__maybe_unsed' because GCC is not capable
to inline such function:
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=67368
With KASAN=n READ_ONCE_NOCHECK() is just a clone of READ_ONCE().
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Kostya Serebryany <kcc@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sasha Levin <sasha.levin@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wolfram Gloger <wmglo@dent.med.uni-muenchen.de>
Cc: kasan-dev <kasan-dev@googlegroups.com>
Link: http://lkml.kernel.org/r/1445243838-17763-2-git-send-email-aryabinin@virtuozzo.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
bdi's are initialized in two steps, bdi_init() and bdi_register(), but
destroyed in a single step by bdi_destroy() which, for a bdi embedded
in a request_queue, is called during blk_cleanup_queue() which makes
the queue invisible and starts the draining of remaining usages.
A request_queue's user can access the congestion state of the embedded
bdi as long as it holds a reference to the queue. As such, it may
access the congested state of a queue which finished
blk_cleanup_queue() but hasn't reached blk_release_queue() yet.
Because the congested state was embedded in backing_dev_info which in
turn is embedded in request_queue, accessing the congested state after
bdi_destroy() was called was fine. The bdi was destroyed but the
memory region for the congested state remained accessible till the
queue got released.
a13f35e871 ("writeback: don't embed root bdi_writeback_congested in
bdi_writeback") changed the situation. Now, the root congested state
which is expected to be pinned while request_queue remains accessible
is separately reference counted and the base ref is put during
bdi_destroy(). This means that the root congested state may go away
prematurely while the queue is between bdi_dstroy() and
blk_cleanup_queue(), which was detected by Andrey's KASAN tests.
The root cause of this problem is that bdi doesn't distinguish the two
steps of destruction, unregistration and release, and now the root
congested state actually requires a separate release step. To fix the
issue, this patch separates out bdi_unregister() and bdi_exit() from
bdi_destroy(). bdi_unregister() is called from blk_cleanup_queue()
and bdi_exit() from blk_release_queue(). bdi_destroy() is now just a
simple wrapper calling the two steps back-to-back.
While at it, the prototype of bdi_destroy() is moved right below
bdi_setup_and_register() so that the counterpart operations are
located together.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: a13f35e871 ("writeback: don't embed root bdi_writeback_congested in bdi_writeback")
Cc: stable@vger.kernel.org # v4.2+
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
Link: http://lkml.kernel.org/g/CAAeHK+zUJ74Zn17=rOyxacHU18SgCfC6bsYW=6kCY5GXJBwGfQ@mail.gmail.com
Reviewed-by: Jan Kara <jack@suse.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For memcg domains, the amount of available memory was calculated as
min(the amount currently in use + headroom according to memcg,
total clean memory)
This isn't quite correct as what should be capped by the amount of
clean memory is the headroom, not the sum of memory in use and
headroom. For example, if a memcg domain has a significant amount of
dirty memory, the above can lead to a value which is lower than the
current amount in use which doesn't make much sense. In most
circumstances, the above leads to a number which is somewhat but not
drastically lower.
As the amount of memory which can be readily allocated to the memcg
domain is capped by the amount of system-wide clean memory which is
not already assigned to the memcg itself, the number we want is
the amount currently in use +
min(headroom according to memcg, clean memory elsewhere in the system)
This patch updates mem_cgroup_wb_stats() to return the number of
filepages and headroom instead of the calculated available pages.
mdtc_cap_avail() is renamed to mdtc_calc_avail() and performs the
above calculation from file, headroom, dirty and globally clean pages.
v2: Dummy mem_cgroup_wb_stats() implementation wasn't updated leading
to build failure when !CGROUP_WRITEBACK. Fixed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: c2aa723a60 ("writeback: implement memcg writeback domain based throttling")
Signed-off-by: Jens Axboe <axboe@fb.com>
bdi_for_each_wb() is used in several places to wake up or issue
writeback work items to all wb's (bdi_writeback's) on a given bdi.
The iteration is performed by walking bdi->cgwb_tree; however, the
tree only indexes wb's which are currently active.
For example, when a memcg gets associated with a different blkcg, the
old wb is removed from the tree so that the new one can be indexed.
The old wb starts dying from then on but will linger till all its
inodes are drained. As these dying wb's may still host dirty inodes,
writeback operations which affect all wb's must include them.
bdi_for_each_wb() skipping dying wb's led to sync(2) missing and
failing to sync the inodes belonging to those wb's.
This patch adds a RCU protected @bdi->wb_list which lists all wb's
beloinging to that bdi. wb's are added on creation and removed on
release rather than on the start of destruction. bdi_for_each_wb()
usages are replaced with list_for_each[_continue]_rcu() iterations
over @bdi->wb_list and bdi_for_each_wb() and its helpers are removed.
v2: Updated as per Jan. last_wb ref leak in bdi_split_work_to_wbs()
fixed and unnecessary list head severing in cgwb_bdi_destroy()
removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Artem Bityutskiy <dedekind1@gmail.com>
Fixes: ebe41ab0c7 ("writeback: implement bdi_for_each_wb()")
Link: http://lkml.kernel.org/g/1443012552.19983.209.camel@gmail.com
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull irq fixes from Thomas Gleixner:
"Three trivial commits:
- Fix a kerneldoc regression
- Export handle_bad_irq to unbreak a driver in next
- Add an accessor for the of_node field so refactoring in next does
not depend on merge ordering"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdomain: Add an accessor for the of_node field
genirq: Fix handle_bad_irq kerneldoc comment
genirq: Export handle_bad_irq
Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.
Nothing major here, full details in the shortlog, and all of these have
been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlYZOFUACgkQMUfUDdst+ymLSACeLNl7IWSxq2acJ5rhUl5+LRxp
KtsAn3lMXJryk4xw2WpfJg30TXpWXnNM
=n9ei
-----END PGP SIGNATURE-----
Merge tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.
Nothing major here, full details in the shortlog, and all of these
have been in linux-next for a while"
* tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: Add device quirk for Logitech PTZ cameras
USB: chaoskey read offset bug
USB: Add reset-resume quirk for two Plantronics usb headphones.
usb: renesas_usbhs: Add support for R-Car H3
usb: renesas_usbhs: fix build warning if 64-bit architecture
usb: gadget: bdc: fix memory leak
phy: berlin-sata: Fix module autoload for OF platform driver
phy: rockchip-usb: power down phy when rockchip phy probe
phy: qcom-ufs: fix build error when the component is built as a module
As we're about to remove the of_node field from the irqdomain
structure, introduce an accessor for it. Subsequent patches
will take care of the actual repainting.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1444402211-1141-1-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull strscpy string copy function implementation from Chris Metcalf.
Chris sent this during the merge window, but I waffled back and forth on
the pull request, which is why it's going in only now.
The new "strscpy()" function is definitely easier to use and more secure
than either strncpy() or strlcpy(), both of which are horrible nasty
interfaces that have serious and irredeemable problems.
strncpy() has a useless return value, and doesn't NUL-terminate an
overlong result. To make matters worse, it pads a short result with
zeroes, which is a performance disaster if you have big buffers.
strlcpy(), by contrast, is a mis-designed "fix" for strlcpy(), lacking
the insane NUL padding, but having a differently broken return value
which returns the original length of the source string. Which means
that it will read characters past the count from the source buffer, and
you have to trust the source to be properly terminated. It also makes
error handling fragile, since the test for overflow is unnecessarily
subtle.
strscpy() avoids both these problems, guaranteeing the NUL termination
(but not excessive padding) if the destination size wasn't zero, and
making the overflow condition very obvious by returning -E2BIG. It also
doesn't read past the size of the source, and can thus be used for
untrusted source data too.
So why did I waffle about this for so long?
Every time we introduce a new-and-improved interface, people start doing
these interminable series of trivial conversion patches.
And every time that happens, somebody does some silly mistake, and the
conversion patch to the improved interface actually makes things worse.
Because the patch is mindnumbing and trivial, nobody has the attention
span to look at it carefully, and it's usually done over large swatches
of source code which means that not every conversion gets tested.
So I'm pulling the strscpy() support because it *is* a better interface.
But I will refuse to pull mindless conversion patches. Use this in
places where it makes sense, but don't do trivial patches to fix things
that aren't actually known to be broken.
* 'strscpy' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: use global strscpy() rather than private copy
string: provide strscpy()
Make asm/word-at-a-time.h available on all architectures
This patch fixes the following warning if 64-bit architecture environment:
./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
dparam->type = of_id ? (u32)of_id->data : 0;
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.1 Enhaned SuperSpeed can set their speed to
HCD_USB31 to let usb core and host drivers know that the controller
supports new USB 3.1 features.
make sure usb core handle HCD_USB31 hosts correctly, for now similar
to HCD_USB3.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device supports usb 3.1 SupeerSpeedPlus Gen2 speeds it povides
a SuperSpeedPlus device capability descriptor as a part of its
BOS descriptor. If we find one while parsing the BOS then save it
togeter with the other device capabilities found in the BOS
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull block fixes from Jens Axboe:
"Another week, another round of fixes.
These have been brewing for a bit and in various iterations, but I
feel pretty comfortable about the quality of them. They fix real
issues. The pull request is mostly blk-mq related, and the only one
not fixing a real bug, is the tag iterator abstraction from Christoph.
But it's pretty trivial, and we'll need it for another fix soon.
Apart from the blk-mq fixes, there's an NVMe affinity fix from Keith,
and a single fix for xen-blkback from Roger fixing failure to free
requests on disconnect"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: factor out a helper to iterate all tags for a request_queue
blk-mq: fix racy updates of rq->errors
blk-mq: fix deadlock when reading cpu_list
blk-mq: avoid inserting requests before establishing new mapping
blk-mq: fix q->mq_usage_counter access race
blk-mq: Fix use after of free q->mq_map
blk-mq: fix sysfs registration/unregistration race
blk-mq: avoid setting hctx->tags->cpumask before allocation
NVMe: Set affinity after allocating request queues
xen/blkback: free requests on disconnection
Pull IOVA fixes from David Woodhouse:
"The main fix here is the first one, fixing the over-allocation of
size-aligned requests. The other patches simply make the existing
IOVA code available to users other than the Intel VT-d driver, with no
functional change.
I concede the latter really *should* have been submitted during the
merge window, but since it's basically risk-free and people are
waiting to build on top of it and it's my fault I didn't get it in, I
(and they) would be grateful if you'd take it"
* git://git.infradead.org/intel-iommu:
iommu: Make the iova library a module
iommu: iova: Export symbols
iommu: iova: Move iova cache management to the iova library
iommu/iova: Avoid over-allocating when size-aligned
Merge misc fixes from Andrew Morton:
"12 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
dmapool: fix overflow condition in pool_find_page()
thermal: avoid division by zero in power allocator
memcg: remove pcp_counter_lock
kprobes: use _do_fork() in samples to make them work again
drivers/input/joystick/Kconfig: zhenhua.c needs BITREVERSE
memcg: make mem_cgroup_read_stat() unsigned
memcg: fix dirty page migration
dax: fix NULL pointer in __dax_pmd_fault()
mm: hugetlbfs: skip shared VMAs when unmapping private pages to satisfy a fault
mm/slab: fix unexpected index mapping result of kmalloc_size(INDEX_NODE+1)
userfaultfd: remove kernel header include from uapi header
arch/x86/include/asm/efi.h: fix build failure
- intel_idle driver fixup for the recently added Skylake chips
support (Len Brown).
- Operating Performance Points (OPP) library fix related to the
recently added support for new DT bindings and a fix for a typo
in a comment (Viresh Kumar, Stephen Boyd).
- ACPI EC driver fix for a recently introduced memory leak in an
error code path (Lv Zheng).
- ACPI PCI IRQ management fix for the issue where an ISA IRQ is
shared with a PCI device which requires it to be configured in a
different way and may cause an interrupt storm to happen as a
result with an extra ACPI SCI IRQ handling simplification on top
of it (Jiang Liu).
- Update of the PCI power management documentation that became
outdated and started to actively confuse the readers to make
it actually reflect the code (Rafael J Wysocki).
- turbostat fixes including an IVB Xeon regression fix (related to
the --debug command line option), Skylake adjustment for the TSC
running at a frequency that doesn't match the base one exactly,
and a Knights Landing quirk to account for the fact that it only
updates APERF and MPERF every 1024 clock cycles plus bumping up
the turbostat version number (Len Brown, Hubert Chrzaniuk).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ELup
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes mostly, for a few changes made in this cycle (the
intel_idle driver, the OPP library, the ACPI EC driver, turbostat) and
for some issues that have just been discovered (ACPI PCI IRQ
management, PCI power management documentation, turbostat), with a
couple of cleanups on top of them.
Specifics:
- intel_idle driver fixup for the recently added Skylake chips
support (Len Brown).
- Operating Performance Points (OPP) library fix related to the
recently added support for new DT bindings and a fix for a typo in
a comment (Viresh Kumar, Stephen Boyd).
- ACPI EC driver fix for a recently introduced memory leak in an
error code path (Lv Zheng).
- ACPI PCI IRQ management fix for the issue where an ISA IRQ is
shared with a PCI device which requires it to be configured in a
different way and may cause an interrupt storm to happen as a
result with an extra ACPI SCI IRQ handling simplification on top of
it (Jiang Liu).
- Update of the PCI power management documentation that became
outdated and started to actively confuse the readers to make it
actually reflect the code (Rafael J Wysocki).
- turbostat fixes including an IVB Xeon regression fix (related to
the --debug command line option), Skylake adjustment for the TSC
running at a frequency that doesn't match the base one exactly, and
a Knights Landing quirk to account for the fact that it only
updates APERF and MPERF every 1024 clock cycles plus bumping up the
turbostat version number (Len Brown, Hubert Chrzaniuk)"
* tag 'pm+acpi-4.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power turbosat: update version number
tools/power turbostat: SKL: Adjust for TSC difference from base frequency
tools/power turbostat: KNL workaround for %Busy and Avg_MHz
tools/power turbostat: IVB Xeon: fix --debug regression
ACPI / PCI: Remove duplicated penalty on SCI IRQ
ACPI, PCI, irq: Do not share PCI IRQ with ISA IRQ
ACPI / EC: Fix a memory leak issue in acpi_ec_query()
PM / OPP: Fix typo modifcation -> modification
PCI / PM: Update runtime PM documentation for PCI devices
PM / OPP: of_property_count_u32_elems() can return errors
intel_idle: Skylake Client Support - updated
Pull networking fixes from David Miller:
1) Fix regression in SKB partial checksum handling, from Pravin B
Shalar.
2) Fix VLAN inside of VXLAN handling in i40e driver, from Jesse
Brandeburg.
3) Cure softlockups during accept() in SCTP, from Karl Heiss.
4) MSG_PEEK should return multiple SKBs worth of data in AF_UNIX, from
Aaron Conole.
5) IPV6 erroneously ignores output interface specifier in lookup key for
route lookups, fix from David Ahern.
6) In Marvell DSA driver, forward unknown frames to CPU port, from
Andrew Lunn.
7) Mission flow flag initializations in some code paths, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: Initialize flow flags in input path
net: dsa: fix preparation of a port STP update
testptp: Silence compiler warnings on ppc64
net/mlx4: Handle return codes in mlx4_qp_attach_common
dsa: mv88e6xxx: Enable forwarding for unknown to the CPU port
skbuff: Fix skb checksum partial check.
net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set
net sysfs: Print link speed as signed integer
bna: fix error handling
af_unix: return data from multiple SKBs on recv() with MSG_PEEK flag
af_unix: Convert the unix_sk macro to an inline function for type safety
net: sctp: Don't use 64 kilobyte lookup table for four elements
l2tp: protect tunnel->del_work by ref_count
net/ibm/emac: bump version numbers for correct work with ethtool
sctp: Prevent soft lockup when sctp_accept() is called during a timeout event
sctp: Whitespace fix
i40e/i40evf: check for stopped admin queue
i40e: fix VLAN inside VXLAN
r8169: fix handling rtl_readphy result
net: hisilicon: fix handling platform_get_irq result
Commit 733a572e66 ("memcg: make mem_cgroup_read_{stat|event}() iterate
possible cpus instead of online") removed the last use of the per memcg
pcp_counter_lock but forgot to remove the variable.
Kill the vestigial variable.
Signed-off-by: Greg Thelen <gthelen@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The problem starts with a file backed dirty page which is charged to a
memcg. Then page migration is used to move oldpage to newpage.
Migration:
- copies the oldpage's data to newpage
- clears oldpage.PG_dirty
- sets newpage.PG_dirty
- uncharges oldpage from memcg
- charges newpage to memcg
Clearing oldpage.PG_dirty decrements the charged memcg's dirty page
count.
However, because newpage is not yet charged, setting newpage.PG_dirty
does not increment the memcg's dirty page count. After migration
completes newpage.PG_dirty is eventually cleared, often in
account_page_cleaned(). At this time newpage is charged to a memcg so
the memcg's dirty page count is decremented which causes underflow
because the count was not previously incremented by migration. This
underflow causes balance_dirty_pages() to see a very large unsigned
number of dirty memcg pages which leads to aggressive throttling of
buffered writes by processes in non root memcg.
This issue:
- can harm performance of non root memcg buffered writes.
- can report too small (even negative) values in
memory.stat[(total_)dirty] counters of all memcg, including the root.
To avoid polluting migrate.c with #ifdef CONFIG_MEMCG checks, introduce
page_memcg() and set_page_memcg() helpers.
Test:
0) setup and enter limited memcg
mkdir /sys/fs/cgroup/test
echo 1G > /sys/fs/cgroup/test/memory.limit_in_bytes
echo $$ > /sys/fs/cgroup/test/cgroup.procs
1) buffered writes baseline
dd if=/dev/zero of=/data/tmp/foo bs=1M count=1k
sync
grep ^dirty /sys/fs/cgroup/test/memory.stat
2) buffered writes with compaction antagonist to induce migration
yes 1 > /proc/sys/vm/compact_memory &
rm -rf /data/tmp/foo
dd if=/dev/zero of=/data/tmp/foo bs=1M count=1k
kill %
sync
grep ^dirty /sys/fs/cgroup/test/memory.stat
3) buffered writes without antagonist, should match baseline
rm -rf /data/tmp/foo
dd if=/dev/zero of=/data/tmp/foo bs=1M count=1k
sync
grep ^dirty /sys/fs/cgroup/test/memory.stat
(speed, dirty residue)
unpatched patched
1) 841 MB/s 0 dirty pages 886 MB/s 0 dirty pages
2) 611 MB/s -33427456 dirty pages 793 MB/s 0 dirty pages
3) 114 MB/s -33427456 dirty pages 891 MB/s 0 dirty pages
Notice that unpatched baseline performance (1) fell after
migration (3): 841 -> 114 MB/s. In the patched kernel, post
migration performance matches baseline.
Fixes: c4843a7593 ("memcg: add per cgroup dirty page accounting")
Signed-off-by: Greg Thelen <gthelen@google.com>
Reported-by: Dave Hansen <dave.hansen@intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org> [4.2+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Fixes for mlx5 related issues
- Fixes for ipoib multicast handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8+cX
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
- Fixes for mlx5 related issues
- Fixes for ipoib multicast handling
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/ipoib: increase the max mcast backlog queue
IB/ipoib: Make sendonly multicast joins create the mcast group
IB/ipoib: Expire sendonly multicast joins
IB/mlx5: Remove pa_lkey usages
IB/mlx5: Remove support for IB_DEVICE_LOCAL_DMA_LKEY
IB/iser: Add module parameter for always register memory
xprtrdma: Replace global lkey with lkey local to PD
And replace the blk_mq_tag_busy_iter with it - the driver use has been
replaced with a new helper a while ago, and internal to the block we
only need the new version.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_complete_request may be a no-op if the request has already
been completed by others means (e.g. a timeout or cancellation), but
currently drivers have to set rq->errors before calling
blk_mq_complete_request, which might leave us with the wrong error value.
Add an error parameter to blk_mq_complete_request so that we can
defer setting rq->errors until we known we won the race to complete the
request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes the following warning if 64-bit architecture environment:
./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
dparam->type = of_id ? (u32)of_id->data : 0;
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Earlier patch 6ae459bda tried to detect void ckecksum partial
skb by comparing pull length to checksum offset. But it does
not work for all cases since checksum-offset depends on
updates to skb->data.
Following patch fixes it by validating checksum start offset
after skb-data pointer is updated. Negative value of checksum
offset start means there is no need to checksum.
Fixes: 6ae459bda ("skbuff: Fix skb checksum flag on skb pull")
Reported-by: Andrew Vagin <avagin@odin.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between cpu hotplug handling and adding/deleting
gendisk for blk-mq, where both are trying to register and unregister
the same sysfs entries.
null_add_dev
--> blk_mq_init_queue
--> blk_mq_init_allocated_queue
--> add to 'all_q_list' (*)
--> add_disk
--> blk_register_queue
--> blk_mq_register_disk (++)
null_del_dev
--> del_gendisk
--> blk_unregister_queue
--> blk_mq_unregister_disk (--)
--> blk_cleanup_queue
--> blk_mq_free_queue
--> del from 'all_q_list' (*)
blk_mq_queue_reinit
--> blk_mq_sysfs_unregister (-)
--> blk_mq_sysfs_register (+)
While the request queue is added to 'all_q_list' (*),
blk_mq_queue_reinit() can be called for the queue anytime by CPU
hotplug callback. But blk_mq_sysfs_unregister (-) and
blk_mq_sysfs_register (+) in blk_mq_queue_reinit must not be called
before blk_mq_register_disk (++) and after blk_mq_unregister_disk (--)
is finished. Because '/sys/block/*/mq/' is not exists.
There has already been BLK_MQ_F_SYSFS_UP flag in hctx->flags which can
be used to track these sysfs stuff, but it is only fixing this issue
partially.
In order to fix it completely, we just need per-queue flag instead of
per-hctx flag with appropriate locking. So this introduces
q->mq_sysfs_init_done which is properly protected with all_q_mutex.
Also, we need to ensure that blk_mq_map_swqueue() is called with
all_q_mutex is held. Since hctx->nr_ctx is reset temporarily and
updated in blk_mq_map_swqueue(), so we should avoid
blk_mq_register_hctx() seeing the temporary hctx->nr_ctx value
in CPU hotplug handling or adding/deleting gendisk .
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull RCU fixes from Paul E. McKenney, for two regressions
introduced in this merge window:
- Fix bug with recent GCCs.
- Fix false positive lockdep splat.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- Replace all "transceiver" with "phy"
- Replace one "OTG controller" with "phy"
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces 'enabled' flag in struct usb_ep, and modifies
usb_ep_enable() and usb_ep_disable() functions to encapsulate endpoint
enabled/disabled state. It helps to avoid enabling endpoints which are
already enabled, and disabling endpoints which are already disables.
From now USB functions don't have to remember current endpoint
enable/disable state, as this state is now handled automatically which
makes this API less bug-prone.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces usb_ep_autoconfig_release() function which allows
to release endpoint previously obtained from usb_ep_autoconfig() during
USB function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct at91_udc_data is now only used inside the driver, move it to its
include.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Set the Power register HSENAB bit based on musb->config->maximum_speed,
so that the glue layer can control MUSB to work in high- or full-speed.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Pull networking fixes from David Miller:
1) When we run a tap on netlink sockets, we have to copy mmap'd SKBs
instead of cloning them. From Daniel Borkmann.
2) When converting classical BPF into eBPF, fix the setting of the
source reg to BPF_REG_X. From Tycho Andersen.
3) Fix igmpv3/mldv2 report parsing in the bridge multicast code, from
Linus Lussing.
4) Fix dst refcounting for ipv6 tunnels, from Martin KaFai Lau.
5) Set NLM_F_REPLACE flag properly when replacing ipv6 routes, from
Roopa Prabhu.
6) Add some new cxgb4 PCI device IDs, from Hariprasad Shenai.
7) Fix headroom tests and SKB leaks in ipv6 fragmentation code, from
Florian Westphal.
8) Check DMA mapping errors in bna driver, from Ivan Vecera.
9) Several 8139cp bug fixes (dev_kfree_skb_any in interrupt context,
misclearing of interrupt status in TX timeout handler, etc.) from
David Woodhouse.
10) In tipc, reset SKB header pointer after skb_linearize(), from Erik
Hugne.
11) Fix autobind races et al. in netlink code, from Herbert Xu with
help from Tejun Heo and others.
12) Missing SET_NETDEV_DEV in sunvnet driver, from Sowmini Varadhan.
13) Fix various races in timewait timer and reqsk_queue_hadh_req, from
Eric Dumazet.
14) Fix array overruns in mac80211, from Johannes Berg and Dan
Carpenter.
15) Fix data race in rhashtable_rehash_one(), from Dmitriy Vyukov.
16) Fix race between poll_one_napi and napi_disable, from Neil Horman.
17) Fix byte order in geneve tunnel port config, from John W Linville.
18) Fix handling of ARP replies over lightweight tunnels, from Jiri
Benc.
19) We can loop when fib rule dumps cross multiple SKBs, fix from Wilson
Kok and Roopa Prabhu.
20) Several reference count handling bug fixes in the PHY/MDIO layer
from Russel King.
21) Fix lockdep splat in ppp_dev_uninit(), from Guillaume Nault.
22) Fix crash in icmp_route_lookup(), from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: Fix panic in icmp_route_lookup
net: update docbook comment for __mdiobus_register()
ppp: fix lockdep splat in ppp_dev_uninit()
net: via/Kconfig: GENERIC_PCI_IOMAP required if PCI not selected
phy: marvell: add link partner advertised modes
net: fix net_device refcounting
phy: add phy_device_remove()
phy: fixed-phy: properly validate phy in fixed_phy_update_state()
net: fix phy refcounting in a bunch of drivers
of_mdio: fix MDIO phy device refcounting
phy: add proper phy struct device refcounting
phy: fix mdiobus module safety
net: dsa: fix of_mdio_find_bus() device refcount leak
phy: fix of_mdio_find_bus() device refcount leak
ip6_tunnel: Reduce log level in ip6_tnl_err() to debug
ip6_gre: Reduce log level in ip6gre_err() to debug
fib_rules: fix fib rule dumps across multiple skbs
bnx2x: byte swap rss_key to comply to Toeplitz specs
net: revert "net_sched: move tp->root allocation into fw_init()"
lwtunnel: remove source and destination UDP port config option
...
Avoid IRQs occupied by ISA IRQs when allocating IRQs for PCI link devices,
otherwise it may cause interrupt storm due to incompatible pin attributes.
This issue was triggered on a KVM virtual machine, which
1) uses IRQ9 for SCI in high level mode.
2) defines an PCI interrupt link device (LNKS) with IRQ9 as the only
possible irq.
3) has an PCI device referring to link device LNKS.
So it causes interrupt storm when enabling the PCI device because PCI IRQ
works in low level mode.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull another cgroup fix from Tejun Heo:
"The cgroup writeback support got inadvertently enabled for traditional
hierarchies revealing two regressions which are currently being worked
on. It shouldn't have been enabled on traditional hierarchies, so
disable it on them. This is enough to make the regressions go away
for people who aren't experimenting with cgroup"
* 'for-4.3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cgroup, writeback: don't enable cgroup writeback on traditional hierarchies
Highlights include:
Stable patches:
- fix v4.2 SEEK on files over 2 gigs
- Fix a layout segment reference leak when pNFS I/O falls back to inband I/O.
- Fix recovery of recalled read delegations
Bugfixes:
- Fix a case where NFSv4 fails to send CLOSE after a server reboot
- Fix sunrpc to wait for connections to complete before retrying
- Fix sunrpc races between transport connect/disconnect and shutdown
- Fix an infinite loop when layoutget fail with BAD_STATEID
- nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
- Fix a bogus WARN_ON_ONCE() in O_DIRECT when layout commit_through_mds is set
- Fix layoutreturn/close ordering issues.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GdeV
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
"Highlights include:
Stable patches:
- fix v4.2 SEEK on files over 2 gigs
- Fix a layout segment reference leak when pNFS I/O falls back to inband I/O.
- Fix recovery of recalled read delegations
Bugfixes:
- Fix a case where NFSv4 fails to send CLOSE after a server reboot
- Fix sunrpc to wait for connections to complete before retrying
- Fix sunrpc races between transport connect/disconnect and shutdown
- Fix an infinite loop when layoutget fail with BAD_STATEID
- nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
- Fix a bogus WARN_ON_ONCE() in O_DIRECT when layout commit_through_mds is set
- Fix layoutreturn/close ordering issues"
* tag 'nfs-for-4.3-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS41: make close wait for layoutreturn
NFS: Skip checking ds_cinfo.buckets when lseg's commit_through_mds is set
NFSv4.x/pnfs: Don't try to recover stateids twice in layoutget
NFSv4: Recovery of recalled read delegations is broken
NFS: Fix an infinite loop when layoutget fail with BAD_STATEID
NFS: Do cleanup before resetting pageio read/write to mds
SUNRPC: xs_sock_mark_closed() does not need to trigger socket autoclose
SUNRPC: Lock the transport layer on shutdown
nfs/filelayout: Fix NULL reference caused by double freeing of fh_array
SUNRPC: Ensure that we wait for connections to complete before retrying
SUNRPC: drop null test before destroy functions
nfs: fix v4.2 SEEK on files over 2 gigs
SUNRPC: Fix races between socket connection and destroy code
nfs: fix pg_test page count calculation
Failing to send a CLOSE if file is opened WRONLY and server reboots on a 4.x mount
Commit 96249d70dd ("IB/core: Guarantee that a local_dma_lkey
is available") allows ULPs that make use of the local dma key to keep
working as before by allocating a DMA MR with local permissions and
converted these consumers to use the MR associated with the PD
rather then device->local_dma_lkey.
ConnectIB has some known issues with memory registration
using the local_dma_lkey (SEND, RDMA, RECV seems to work ok).
Thus don't expose support for it (remove device->local_dma_lkey
setting), and take advantage of the above commit such that no regression
is introduced to working systems.
The local_dma_lkey support will be restored in CX4 depending on FW
capability query.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
