Follow-up to commit c7272ca720 ("bpf: add initial support for
attaching xdp progs") to also support generic XDP. This adds an
indicator for loaded generic XDP programs when programs are loaded
as shown in c7272ca720, but the driver still lacks native XDP
support.
# ip link
[...]
3: eno1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 xdpgeneric qdisc [...]
link/ether 0c:c4:7a:03:f9:25 brd ff:ff:ff:ff:ff:ff
[...]
In case the driver does support native XDP, but the user wants
to load the program as generic XDP (e.g. for testing purposes),
then this can be done with the same semantics as in c7272ca720,
but with 'xdpgeneric' instead of 'xdp' command for loading:
# ip -force link set dev eno1 xdpgeneric obj xdp.o
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: David S. Miller <davem@davemloft.net>
For example, forward udp traffic destined to port 999 to veth0 and set
tcp port to 888:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto udp \
dst_port 999 \
action pedit ex munge \
udp dport set 888 \
action mirred egress \
redirect dev veth0
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
For example, forward tcp traffic destined to port 80 to veth0 and set
tcp port to 8080:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto tcp \
dst_port 80 \
action pedit ex munge \
tcp dport set 8080 \
action mirred egress \
redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
For example, forward tcp traffic to veth0 and set
destination mac address to 11:22:33:44:55:66 :
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto tcp \
action pedit ex munge \
eth dst set 11:22:33:44:55:66 \
action mirred egress \
redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
Enable user to edit IP header ttl field.
For example, to forward any TCP packet and decrease its TTL by one:
$ tc filter add dev enp0s9 protocol ip parent ffff: \
flower \
ip_proto tcp \
action pedit ex munge \
ip ttl add 0xff pipe \
action mirred egress \
redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
Utilize the extended pedit netlink to set an offset relative to a
specific header type. Old netlink only enabled the user to set
approximated offset relative to the IPv4 header.
To use this extended functionality need to use the 'ex' keyword after
'pedit' and before any 'munge'.
e.g:
$ tc filter add dev ens9 protocol ip parent ffff: \
flower \
ip_proto udp \
dst_port 80 \
action pedit ex munge \
ip dst set 1.1.1.1 \
pipe \
action mirred egress redirect dev veth0
Signed-off-by: Amir Vadai <amir@vadai.me>
Despite the past changes, users seemed to get confused by the seemingly
contradictory relation of priority value and actual rule priority.
Signed-off-by: Phil Sutter <phil@nwl.cc>
This patch adds information about seg6 encapsulation in the ip-route
manual, as well as the ip-sr manual page.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Add support for setting and displaying the ttl attribute
for MPLS IP lighweight tunnels.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Add support for setting and displaying the ttl-propagation attribute
initially used by MPLS to control propagation of MPLS TTL to IPv4/IPv6
TTL/hop-limit on popping final label on a per-route basis.
Signed-off-by: Robert Shearman <rshearma@brocade.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
While generating PDFs from the man pages, I saw the warning below from
several files. Compared the tc-matchall.8 with bridge.8 and used .RI
instead of .R. It should have no effect on the man page rendering.
`R' is a string (producing the registered sign), not a macro.
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Having some examples in the top level man page might make it a little bit easier
for new users to get started. Reused some words / sentences from the existing
man pages.
Suggested-by: 積丹尼 Dan Jacobson <jidanni@jidanni.org>
Signed-off-by: Alexander Alemayhu <alexander@alemayhu.com>
Add support for new afstats subcommand. This uses the new
IFLA_STATS_AF_SPEC attribute of RTM_GETSTATS messages to show
per-device, AF-specific stats. At the moment the kernel only supports
MPLS AF stats, so that is all that's implemented here.
The print_num function is exposed from ipaddress.c to be used for
printing the new stats so that the human-readable option, if set, can
be respected.
Example of use:
$ ./ip/ip -f mpls link afstats dev eth1
3: eth1
mpls:
RX: bytes packets errors dropped noroute
9016 98 0 0 0
TX: bytes packets errors dropped
7232 113 0 0
Signed-off-by: Robert Shearman <rshearma@brocade.com>
This patch adds support for a new xstats link subcommand which uses the
specified link type's new parse/print_ifla_xstats callbacks to display
extended statistics.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Extend ICMP code and type match to support masks.
Also add missing documentation to synopsis in manpage.
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128/240 code 0 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Unlike other PREFIXes documented in the usage for tc flower, which accept
both IPv4 and IPv6 prefixes, arp_sip and arp_tip only accepts IPv4
prefixes.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Add an example of packet sampling to the tc-matchall man page examples
section. The example uses the matchall classifier and the sample action to
create packet sampling on a port.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
In addition to general information about the tc action, the man entry
contains common usage examples and information about the tlv fields packed
within each sampled packet.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Descriptions of each route sub-command's arguments are enclosed in
.RS/.RE pairs. For 'replace' sub-command, '.RE' was incorrectly put
before the last argument ('expires').
Fixes: 3fbe7ca847 ("iproute2: ip-route.8.in: Add expires option for ip route")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Add documentation about the extended statistics to the ifstat man page.
Add ifstat man age to the man8 Makefile
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
The man page contains two examples, which have different indentation. Fix
the indentation of the two examples to match.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
This fixes two issues with the provided example:
- Add missing 'dev' keyword to second command.
- Use a real IPv4 address instead of a bogus hex value since that will
be rejected by get_addr_ipv4().
Fixes: dbfb17a67f ("man: tc-csum.8: Add an example")
Reported-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Instead of "magic numbers" we can now specify each flag
by name. Prefix of "no" (e.g nofrag) unsets the flag,
otherwise it wil be set.
Example:
# add a flower filter that will drop fragmented packets
tc filter add dev ens4f0 protocol ip parent ffff: \
flower \
src_mac e4:1d:2d:fd:8b:01 \
dst_mac e4:1d:2d:fd:8b:02 \
indev ens4f0 \
ip_flags frag \
action drop
# add a flower filter that will drop non-fragmented packets
tc filter add dev ens4f0 protocol ip parent ffff: \
flower \
src_mac e4:1d:2d:fd:8b:01 \
dst_mac e4:1d:2d:fd:8b:02 \
indev ens4f0 \
ip_flags nofrag \
action drop
Fixes: 22a8f01989 ('tc: flower: support matching flags')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Correct typo in example in ife man page.
Fixes: 06f9a59170 ("man: tc-ife.8: man page for ife action")
Cc: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
This patch adds a new argument to the bridge fdb show command that allows
to filter by entry state.
Also update the man page to include all available show arguments.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Since 41aa17ff46 ("tc/cls_flower: Add dest UDP port to tunnel params")
tc flower supports setting the dest UDP port.
* Use "port_number" to be consistent with other man-page text
* Re-add "enc_dst_port" documentation to manpage which was
accidently removed by b2a1f740aa ("tc: flower: document that *_ip
parameters take a PREFIX as an argument.")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_mac and dst_mac may now take an optional mask
to limit the scope of matching.
* This address is is documented as a LLADDR in keeping with ip-link(8).
* The formats accepted match those already output when dumping flower
filters from the kernel.
Example of use of LLADDR with and without a mask:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:01:00:00:00/ff:ff:00:00:00:01 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00/23 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_ip, dst_ip, enc_src_ip and enc_dst_ip take an
optional prefix length which is used to provide a mask to limit the scope
of matching.
* This is documented as a PREFIX in keeping with ip-route(8).
Example of uses of IPv4 and IPv6 prefixes
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 dst_ip 192.168.1.1 action drop
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 src_ip 10.0.0.0/8 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 src_ip 2001:DB8:1::/48 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 dst_ip 2001:DB8::1 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_mac and dst_mac may now take an optional mask
to limit the scope of matching.
* This address is is documented as a LLADDR in keeping with ip-link(8).
* The formats accepted match those already output when dumping flower
filters from the kernel.
Example of use of LLADDR with and without a mask:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:01:00:00:00/ff:ff:00:00:00:01 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00/23 action drop
tc filter add dev eth0 protocol ip parent ffff: flower indev eth0 \
src_mac 52:54:00:00:00:00 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
* The argument to src_ip, dst_ip, enc_src_ip and enc_dst_ip take an
optional prefix length which is used to provide a mask to limit the scope
of matching.
* This is documented as a PREFIX in keeping with ip-route(8).
Example of uses of IPv4 and IPv6 prefixes
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 dst_ip 192.168.1.1 action drop
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 src_ip 10.0.0.0/8 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 src_ip 2001:DB8:1::/48 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 dst_ip 2001:DB8::1 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
'ip vrf' follows the user semnatics established by 'ip netns'.
The 'ip vrf' subcommand supports 3 usages:
1. Run a command against a given vrf:
ip vrf exec NAME CMD
Uses the recently committed cgroup/sock BPF option. vrf directory
is added to cgroup2 mount. Individual vrfs are created under it. BPF
filter attached to vrf/NAME cgroup2 to set sk_bound_dev_if to the VRF
device index. From there the current process (ip's pid) is addded to
the cgroups.proc file and the given command is exected. In doing so
all AF_INET/AF_INET6 (ipv4/ipv6) sockets are automatically bound to
the VRF domain.
The association is inherited parent to child allowing the command to
be a shell from which other commands are run relative to the VRF.
2. Show the VRF a process is bound to:
ip vrf id
This command essentially looks at /proc/pid/cgroup for a "::/vrf/"
entry with the VRF name following.
3. Show process ids bound to a VRF
ip vrf pids NAME
This command dumps the file MNT/vrf/NAME/cgroup.procs since that file
shows the process ids in the particular vrf cgroup.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
To be installed with the other man pages.
Fixes: d57639a475 ("tc/act_tunnel: Introduce ip tunnel action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Replace vlan_eth_type with vlan_ethtype.
Fixes: 745d917260 ("tc: flower: Introduce vlan support")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Enhance tunnel key action parameters by adding destination UDP port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Enhance IP tunnel parameters by adding destination UDP port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Adds support to configure BPF programs as nexthop actions via the LWT
framework.
Example:
ip route add 192.168.253.2/32 \
encap bpf out obj lwt_len_hist_kern.o section len_hist \
dev veth0
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Support matching on ICMP type and code.
Example usage:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 ip_proto icmp type 8 code 0 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128 code 0 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Now that we made the BPF loader generic as a library, reuse it
for loading XDP programs as well. This basically adds a minimal
start of a facility for iproute2 to load XDP programs. There
currently only exists the xdp1_user.c sample code in the kernel
tree that sets up netlink directly and an iovisor/bcc front-end.
Since we have all the necessary infrastructure in place already
from tc side, we can just reuse its loader back-end and thus
facilitate migration and usability among the two for people
familiar with tc/bpf already. Sharing maps, performing tail calls,
etc works the same way as with tc. Naturally, once kernel
configuration API evolves, we will extend new features for XDP
here as well, resp. extend dumping of related netlink attributes.
Minimal example:
clang -target bpf -O2 -Wall -c prog.c -o prog.o
ip [-force] link set dev em1 xdp obj prog.o # attaching
ip [-d] link # dumping
ip link set dev em1 xdp off # detaching
For the dump, intention is that in the first line for each ip
link entry, we'll see "xdp" to indicate that this device has an
XDP program attached. Once we dump some more useful information
via netlink (digest, etc), idea is that 'ip -d link' will then
display additional relevant program information below the "link/
ether [...]" output line for such devices, for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
This is needed for some HWs to do proper macthing and steering.
Possible values are none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add missing usage help for devlink dev eswitch subcommand.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Remove references to eth_type and ether_type (spelling error) in
the tc flower manpage.
Also correct formatting of boldface text with whitespace.
Cc: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This action could be used before redirecting packets to a shared tunnel
device, or when redirecting packets arriving from a such a device.
The 'unset' action is optional. It is used to explicitly unset the
metadata created by the tunnel device during decap. If not used, the
metadata will be released automatically by the kernel.
The 'set' operation, will set the metadata with the specified values for
the encap.
For example, the following flower filter will forward all ICMP packets
destined to 11.11.11.2 through the shared vxlan device 'vxlan0'. Before
redirecting, a metadata for the vxlan tunnel is created using the
tunnel_key action and it's arguments:
$ tc filter add dev net0 protocol ip parent ffff: \
flower \
ip_proto 1 \
dst_ip 11.11.11.2 \
action tunnel_key set \
src_ip 11.11.0.1 \
dst_ip 11.11.0.2 \
id 11 \
action mirred egress redirect dev vxlan0
Signed-off-by: Amir Vadai <amir@vadai.me>
Introduce classifying by metadata extracted by the tunnel device.
Outer header fields - source/dest ip and tunnel id, are extracted from
the metadata when classifying.
For example, the following will add a filter on the ingress Qdisc of shared
vxlan device named 'vxlan0'. To forward packets with outer src ip
11.11.0.2, dst ip 11.11.0.1 and tunnel id 11. The packets will be
forwarded to tap device 'vnet0':
$ tc filter add dev vxlan0 protocol ip parent ffff: \
flower \
enc_src_ip 11.11.0.2 \
enc_dst_ip 11.11.0.1 \
enc_key_id 11 \
dst_ip 11.11.11.1 \
action mirred egress redirect dev vnet0
Signed-off-by: Amir Vadai <amir@vadai.me>
This is needed for some HWs to do proper macthing and steering.
Possible values are none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add missing usage help for devlink dev eswitch subcommand.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Cc: steweg@gmail.com
v5:
- rebase and fix checkpatch
v4:
- add MACADDR_SET support
- skip FLAG_UNICAST / FLAG_UNICAST_ALL as this is not upstream
- fix man page
This makes use of the sctp_diag interface recently added to the kernel.
Joint work with Xin Long who provided the PoC implementation which I
merely polished up a bit.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Remove left over usage from removal of eth_type argument.
Fixes: 488b41d020 ('tc: flower no need to specify the ethertype')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
So far, only the 'egress' direction was implemented.
Allow specifying 'ingress' as the direction packet appears on the target
interface.
For example, this takes incoming 802.1q frames on veth0 and redirects
them for input on dummy0:
# tc filter add dev veth0 parent ffff: pref 1 protocol 802.1q basic \
action mirred ingress redirect dev dummy0
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Recently a new per-port flag was added which controls the flooding of
unknown multicast, this patch adds support for controlling it via iproute2.
It also updates the man pages with information about the new flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Add support for controling hardware offload using (now standard)
skip_sw and skip_hw flags in cls_bpf.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Cc: steweg@gmail.com
