As 'ip' util will share the same netns from the caller
process then we can just look at /proc/self/.. to show
the netns of the current process by:
ip netns id
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Man pages for Foo-over-UDP and Generic UDP Encapsulation receive
port configuration. gue man page links to fou one.
Signed-off-by: Tom Herbert <therbert@google.com>
For hsr link there was no short description in ip-link man page.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Not sure how these typos slipped in back then, I suspect
too much coffee. ;) So lets fix them up properly.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
o "min_tx_rate" option has been added for minimum Tx rate. Hence, for
consistent naming, "max_tx_rate" option has been introduced for maximum
Tx rate.
o Change in v2: "rate" can be used along with "max_tx_rate".
When both are specified, "max_tx_rate" should override.
o Change in v3:
* IFLA_VF_RATE: When IFLA_VF_RATE is used, and user has given only one of
min_tx_rate or max_tx_rate, reading of previous rate limits is done in
userspace instead of in kernel space before ndo_set_vf_rate.
* IFLA_VF_TX_RATE: When IFLA_VF_TX_RATE is used, min_tx_rate is always read
in kernel space. This takes care of below scenarios:
(1) when old tool sends "rate" but kernel is new (expects min and max)
(2) when new tool sends only "rate" but kernel is old (expects only "rate")
o Change in v4 as suggested by Stephen Hemminger:
* As per iproute policy, input and output formats should match. Changing display
of max_tx_rate and min_tx_rate options accordingly.
./ip/ip link show p3p1
8: p3p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000
link/ether 00:0e:1e:16:ce:40 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 2a:18:8f:4d:3d:d4, tx rate 700 (Mbps), max_tx_rate 700Mbps, min_tx_rate 200Mbps
vf 1 MAC 72:dc:ba:f9:df:fd
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Controller Area Network (CAN) interfaces are physical network interfaces.
They can't be 'created' like software devices by 'ip link add type can'.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
The process SELinux contexts can be added to the output using the -Z
option. Using the -z option will show the process and socket contexts (see
the man page for details).
For netlink sockets: if valid process show process context, if pid = 0
show kernel initial context, if unknown show "unavailable".
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
This adds the manpage for PIE: Proportional Integral controller Enhanced AQM
scheme.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Vijay Subramanian <vijaynsu@cisco.com>
CC: Dave Taht <dave.taht@bufferbloat.net>
This augments bridge(8) manual page with `bridge mdb' and `bridge
monitor mdb' commands which have been added recently.
Signed-off-by: Petr Písař <ppisar@redhat.com>
When configuring a system with multiple network uplinks and default routes, it
is often convenient to reference a routing table multiple times - but reject
its routing decision if certain constraints are not met by it.
Consider this setup:
$ ip route add table secuplink default via 10.42.23.1
$ ip rule add pref 100 table main suppress_prefixlength 0
$ ip rule add pref 150 fwmark 0xA table secuplink
With this setup, packets marked 0xA will be processed by the additional routing
table "secuplink", but only if no suitable route in the main routing table can
be found. By suppressing entries with a prefixlength of 0 (or less), the
default route (/0) of the table "main" is hidden to packets processed by rule
100; packets traveling to destinations via more specific routes are processed
as usual.
It is also possible to suppress a routing entry if a device belonging to
a specific interface group is to be used:
$ ip rule add pref 150 table main suppress_group 1
Signed-off-by: Stefan Tomanek <stefan.tomanek@wertarbyte.de>
This patch allows setting VXLAN destination to unicast address.
It allows that VXLAN can be used as peer-to-peer tunnel without
multicast.
v6: change back to the v3 except for using new attribute because
replacing command-line parameters breaks existing scripts,
based by Cong Wang's comments.
v5: rebase on the latest.
v4: replace "group" with "remote" based by David Stevens's comments.
v3: move a new attribute REMOTE into the last of an enum list
based by Stephen Hemminger's comments.
fix the usage to show explicitly that both "remote" and "group"
cannot be specified, based by Ben Hutchings's comments.
v2: use a new argument "remote" instead of "group" based by
Stephen Hemminger's comments.
Signed-off-by: Atzm Watanabe <atzm@stratosphere.co.jp>
These do nothing on an 80-column display. They were clearly somebody's
boilerplate way of setting up hanging indents, but the syntax lines
are way too short to require them. And since most were argumentless
they would have been no-ops on any sized display.
The ip link command line help and the ip-link.8.in
man page are outdated in regards to the vxlan support.
The patch updates both the command line help for the
ip command and its man page.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
The bridge fdb command line help and the bridge.8
man page are outdated in regards to the vxlan support.
The patch updates both the command line help for the
bridge command and its man page.
Signed-off-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
The command synopsis is regularized and part of it split off into an
OPTIONS section. This allows the page to lift to XML-DocBook.
An invalid \p escape was removed.
This page was written by someone who didn't understand the use of
definite and indefinite articles in English, nor its punctuation rules.
I've fixed these mistakes, and some glitches in punctuation and
capitalization.
Enclosed patch fixes inappropriate uses of the .SS macro. Fuller explanation
in the change comment.
There are other problems in these pages that block lifting to
XML-DocBook, most notably in the command synopses. They will take
some creativity to fix. I'm working on it
>From 75745adba4b45b87577b61a2daa886dd444f44da Mon Sep 17 00:00:00 2001
From: "Eric S. Raymond" <esr@thyrsus.com>
Date: Fri, 21 Jun 2013 15:27:38 -0400
Subject: [PATCH] Abolish presentation-level misuse of the .SS macro.
This change fixes most (but not all) fatal errors in attempts to lift
the iproute2 manual pages to XML-DocBook. Where .SS is still used it
is a real subsection header, not just a way to outdent and bold text.
Presentation-level instances are turned into .TP calls and tables.
This patch adds quickack option to enable/disable TCP quick ack
mode for per-route.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Cong Wang <amwang@redhat.com>
This patch adds support for tokenized IIDs, that enable
administrators to assign well-known host-part addresses
to nodes whilst still obtaining global network prefix
from Router Advertisements. This is the iproute2 part for
the kernel patch f53adae4eae5 (``net: ipv6: add tokenized
interface identifier support'').
Example commands with iproute2:
Setting a device token:
# ip token set ::1a:2b:3c:4d/64 dev eth1
Getting a device token:
# ip token get dev eth1
token ::1a:2b:3c:4d dev eth1
Listing all tokens:
# ip token list (or: ip token)
token :: dev eth0
token ::1a:2b:3c:4d dev eth1
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
