This moves the warning to the beginning of the section about 'ip link
set' which makes it still stand out after adding more text to it's end.
Signed-off-by: Phil Sutter <phil@nwl.cc>
'ip link set' supports passing a type to set type-specific parameters.
Add this missing piece of information to the synopsis section.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Add option to suppress header line. When used the following line
is not shown:
"State Recv-Q Send-Q Local Address:Port Peer Address:Port"
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Add two NLA's that allow configuration of Infiniband node or port GUIDs
by referencing the IPoIB net device set over the physical function. The
format to be used is as follows:
ip link set dev ib0 vf 0 node_guid 00:02:c9:03:00:21:6e:70
ip link set dev ib0 vf 0 port_guid 00:02:c9:03:00:21:6e:78
Signed-off-by: Eli Cohen <eli@mellanox.com>
Add vrf keyword to 'ip route' commands. Allows:
1. Users can list routes by VRF name:
$ ip route show vrf NAME
VRF tables have all routes including local and broadcast routes.
The VRF keyword filters LOCAL and BROADCAST routes; to see all
routes the table option can be used. Or to see local routes only
for a VRF:
$ ip route show vrf NAME type local
2. Add or delete a route for a VRF:
$ ip route {add|delete} vrf NAME <route spec>
3. Do a route lookup for a VRF:
$ ip route get vrf NAME ADDRESS
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Add vrf keyword to 'ip neigh' commands. Allows listing neighbor
entries for all links associated with a given VRF.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Add vrf keyword to 'ip link' and 'ip addr' commands (common list code).
Allows:
1. Adding a link to a VRF
$ ip link set NAME vrf NAME
Removing a link from a VRF still uses 'ip link set NAME nomaster'
2. Showing links associated with a VRF:
$ ip link show vrf NAME
3. List addresses associated with links in a VRF
$ ip -br addr show vrf red
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
On devices that support TC flower offloads, these flags enable a filter to be
added only to HW or only to SW. skip_sw and skip_hw are mutually exclusive
flags. By default without any flags, the filter is added to both HW and SW,
but no error checks are done in case of failure to add to HW.
With skip-sw, failure to add to HW is treated as an error.
Here is a sample script that adds 2 filters, one with skip_sw and the other
with skip_hw flag.
# add ingress qdisc
tc qdisc add dev enp0s9 ingress
# enable hw tc offload.
ethtool -K enp0s9 hw-tc-offload on
# add a flower filter with skip-sw flag.
tc filter add dev enp0s9 protocol ip parent ffff: flower \
ip_proto 1 indev enp0s9 skip_sw \
action drop
# add a flower filter with skip-hw flag.
tc filter add dev enp0s9 protocol ip parent ffff: flower \
ip_proto 3 indev enp0s9 skip_hw \
action drop
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Doc text shamelessly stolen from the introducing commit's message
(6c55c8c461 ['ip link set vf: Added "query_rss" command']).
Signed-off-by: Phil Sutter <phil@nwl.cc>
Not sure why this was limited to ip-link before. It is semantically
equal to the 'master' keyword, which is not restricted at all.
The man page and help text adjustments include the 'master' keyword as
well since that is also supported but wasn't documented before.
Cc: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Phil Sutter <phil@nwl.cc>
Extend ip-link to create MACsec devices
ip link add link <master> <macsec> type macsec [options]
Add `ip macsec` command to configure receive-side secure channels and
secure associations within a macsec netdevice.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Phil Sutter <phil@nwl.cc>
This patch drops the redundant description of some of ip's options in
ip-link.8's description of the 'show' subcommand, preserving the
description of -iec (but appending it to the list in ip.8 with minor
fixes).
Signed-off-by: Phil Sutter <phil@nwl.cc>
Follow-up for kernel commit 8eb3b99554b8 ("geneve: support setting
IPv6 flow label") to allow setting the label for the device config.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Follow-up for kernel commit e7f70af111f0 ("vxlan: support setting
IPv6 flow label") to allow setting the label for the device config.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This should be made generic and part of a common tc-actions man page.
Though leave it here for now to not confuse readers of the example which
uses it.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
As Jamal pointed out, there are two different approaches to bandwidth
measurement. Try to make this clear by separating them in synopsis and
also documenting the way to fine-tune avrate.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
As Jamal suggested, BRANCH is the wrong name, as these keywords go
beyond simple branch control - e.g. loops are possible, too. Therefore
rename the non-terminal to CONTROL instead which should be more
appropriate.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Recently a new temp router port mode was added and with it the dumped
information was extended similar to how mdb entries were done. This
patch adds support to dump the new information by using the "-s" switch.
Example:
$ bridge -d -s mdb show
dev br0 port eth1 grp ff02::1:ffbf:5716 temp 234.39
dev br0 port eth1 grp 239.0.0.2 temp 97.17
dev br0 port eth1 grp 239.0.0.3 temp 105.36
router ports on br0: eth1 0.00 permanent
router ports on br0: eth2 254.87 temp
It also updates the bridge man page.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Not sure how useful they are in practice, but as 'ip neigh' supports
setting them all, they deserve to be described as well.
While at it, also add a missing layer of indentation to the subordinate
nud state list.
Signed-off-by: Phil Sutter <phil@nwl.cc>
The documentation is wrong here: it is indeed possible to remove policy
rule 0 and recreate it afterwards. Therefore remove these statements.
Signed-off-by: Phil Sutter <phil@nwl.cc>
While the synopsis section contains 'ip route list', it is later
described as 'ip route show'. Make this consistent by replacing 'list'
with 'show' in synopsis.
Signed-off-by: Phil Sutter <phil@nwl.cc>
