Add section for additional arguments to GRE, IPIP, and SIT types
that are related to Foo-over-UDP and Generic UDP Encapsulation.
Also, added an example GUE configuration in the examples section.
Signed-off-by: Tom Herbert <therbert@google.com>
This change allows to exec some cmd on each
named netns (except default) by specifying '-all' option:
# ip -all netns exec ip link
Each command executes synchronously.
Exit status is not considered, so there might be a case
that some CMD can fail on some netns but success on the other.
EXAMPLES:
1) Show link info on all netns:
$ ip -all netns exec ip link
netns: test_net
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether 1a:19:6f:25:eb:85 brd ff:ff:ff:ff:ff:ff
netns: home0
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether ea:1a:59:40:d3:29 brd ff:ff:ff:ff:ff:ff
netns: lan0
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
4: tap0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN mode DEFAULT group default qlen 500
link/ether ce:49:d5:46:81:ea brd ff:ff:ff:ff:ff:ff
2) Set UP tap0 device for the all netns:
$ ip -all netns exec ip link set dev tap0 up
netns: test_net
netns: home0
netns: lan0
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
In the ip-link(8) man page, for the gretap, ip6gre, and ip6gretap types, the
word tunnel was incorrectly spelled 'tuunel'.
Signed-off-by: Reese Moore <ram@vt.edu>
v2:
Resending now that the dust has cleared in 3.18 on "self" vs. hwmode debate for
brport settings. learning_sync is now set/cleared using "self" qualifier on
brport.
v1:
Add 'learned_sync' flag to turn on/off syncing of learned MAC addresses from
offload device to bridge's FDB. Flag is be set/cleared on offload device port
using "self" qualifier:
$ sudo bridge link set dev swp1 learning_sync on self
$ bridge -d link show dev swp1
2: swp1 state UNKNOWN : <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br0 state forwarding priority 32 cost 2
hairpin off guard off root_block off fastleave off learning off flood off
2: swp1 state UNKNOWN : <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 master br0
learning on learning_sync on
Adds new IFLA_BRPORT_LEARNED_SYNCED attribute for IFLA_PROTINFO on the SELF
brport.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Added new '-netns' option to simplify executing following cmd:
ip netns exec NETNS ip OPTIONS COMMAND OBJECT
to
ip -n[etns] NETNS OPTIONS COMMAND OBJECT
e.g.:
ip -net vnet0 link add br0 type bridge
ip -n vnet0 link
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Extend "ip-address" man page to reflect the recent extension of
allowing to list addresses with flags tentative, deprecated, dadfailed
not being set.
Signed-off-by: Heiner Kallweit <heiner.kallweit@web.de>
Added new option 'type' to 'ip link show'
command which allows to filter devices by type:
ip link show type bridge
ip link show type vlan
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Added another timestamp format to look like more logging info:
[2014-12-22T22:36:50.489 ] 2: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default
link/ether 3c:97:0e:a3:86:2e brd ff:ff:ff:ff:ff:ff
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This permits to selectively enable explicit congestion notification via
the routing table.
If this ecn feature is not set, the kernel will use the tcp_ecn sysctl
to decide wheter to use ECN when establising a TCP connection.
At the time of this writing, the kernel supports ecn and allfrags, but
allfrags is of dubious value and not implemented here.
Example:
ip route change 192.168.2.0/24 dev eth0 features ecn
Signed-off-by: Florian Westphal <fw@strlen.de>
BEFORE:
The show command has additional formatting options:
-s, -stats, -statistics
output more statistics about packet usage.
-d, -details
output more detailed information.
-h, -human, -human-readble
output statistics with human readable values number followed by suffix
-iec print human readable rates in IEC units (ie. 1K = 1024).
AFTER:
The show command has additional formatting options:
-s, -stats, -statistics
output more statistics about packet usage.
-d, -details
output more detailed information.
-h, -human, -human-readble
output statistics with human readable values number followed by suffix
-iec print human readable rates in IEC units (ie. 1K = 1024).
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
As 'ip' util will share the same netns from the caller
process then we can just look at /proc/self/.. to show
the netns of the current process by:
ip netns id
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Man pages for Foo-over-UDP and Generic UDP Encapsulation receive
port configuration. gue man page links to fou one.
Signed-off-by: Tom Herbert <therbert@google.com>
For hsr link there was no short description in ip-link man page.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Not sure how these typos slipped in back then, I suspect
too much coffee. ;) So lets fix them up properly.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
o "min_tx_rate" option has been added for minimum Tx rate. Hence, for
consistent naming, "max_tx_rate" option has been introduced for maximum
Tx rate.
o Change in v2: "rate" can be used along with "max_tx_rate".
When both are specified, "max_tx_rate" should override.
o Change in v3:
* IFLA_VF_RATE: When IFLA_VF_RATE is used, and user has given only one of
min_tx_rate or max_tx_rate, reading of previous rate limits is done in
userspace instead of in kernel space before ndo_set_vf_rate.
* IFLA_VF_TX_RATE: When IFLA_VF_TX_RATE is used, min_tx_rate is always read
in kernel space. This takes care of below scenarios:
(1) when old tool sends "rate" but kernel is new (expects min and max)
(2) when new tool sends only "rate" but kernel is old (expects only "rate")
o Change in v4 as suggested by Stephen Hemminger:
* As per iproute policy, input and output formats should match. Changing display
of max_tx_rate and min_tx_rate options accordingly.
./ip/ip link show p3p1
8: p3p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT qlen 1000
link/ether 00:0e:1e:16:ce:40 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 2a:18:8f:4d:3d:d4, tx rate 700 (Mbps), max_tx_rate 700Mbps, min_tx_rate 200Mbps
vf 1 MAC 72:dc:ba:f9:df:fd
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Controller Area Network (CAN) interfaces are physical network interfaces.
They can't be 'created' like software devices by 'ip link add type can'.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
The process SELinux contexts can be added to the output using the -Z
option. Using the -z option will show the process and socket contexts (see
the man page for details).
For netlink sockets: if valid process show process context, if pid = 0
show kernel initial context, if unknown show "unavailable".
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
This adds the manpage for PIE: Proportional Integral controller Enhanced AQM
scheme.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: Vijay Subramanian <vijaynsu@cisco.com>
CC: Dave Taht <dave.taht@bufferbloat.net>
