On Mon, 2013-06-03 at 16:36 +0100, Ben Hutchings wrote:
> Oops, I read this as being strtol() currently, not strtod(). Currently
> '1.5gbit' will work, but this change will break that. So I think you
> need to keep bps as a double.
Arg
> Then here I think the check should be *rate != floor(bps), i.e. accept
> rounding down of a non-integer number of bytes but any other change is
> assumed to be overflow.
Thanks Ben, here is v4 then ;)
[PATCH v4] get_rate: detect 32bit overflows
Current rate limit is 34.359.738.360 bit per second, and
unfortunately 40Gbps links are above it.
overflows in get_rate() are currently not detected, and some
users are confused. Let's detect this and complain.
Note that some qdisc are ready to get extended range, but this will
need additional attributes and new iproute2
With help from Ben Hutchings
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
"tc class show dev ..." omits the overhead attribute for HTB.
After patch I have :
tc class add dev $DEV parent 1: classid 1:1 est 1sec 4sec htb \
rate 12Mbit mtu 1500 quantum 1514 overhead 20
tc class show dev $DEV
class htb 1:1 root prio 0 rate 12000Kbit overhead 20 ceil 12000Kbit
burst 1500b cburst 1500b
Signed-off-by: Eric Dumazet <edumazet@google.com>
In trying to build on a RHEL6.3 I ran into several build issues that are
addressed in this patch.
The first is that xtables_merge_options only has 3 parameters. It appears
this is how this code was originally. As such for the case where the version
is less than 6 I am assuming it would be correct to maintain the original
setup that only had 3 parameters being passed instead of 4.
I also ran into an issue with the define for __ALIGN_KERNEL not being present.
I believe this may be due to the fact that __ALIGN_KERNEL was moved into a
separate header from ALIGN after the UAPI changes. In order to just cover all
of the bases I have moved the main definition for the macros into
__ALIGN_KERNEL_MASK and __ALIGN_KERNEL and if ALIGN is also needed then it is
just a direct redefine to __ALIGN_KERNEL.
Cc: Hasan Chowdhury <shemonc@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Clearer error messages for fifo and tbf qdiscs:
- Say who is complaining
- Don't just say a parameter is bad, show the offending parameter
- Be clearer about duplicate parameters vs illegal pairs of parameters
- Try to give multiple error messages rather than let the user discover the errors one by one
- When there are parameter aliases, try to use the variant that was used, or at least mention them all
Note that in the old version an empty parameter list to tbf would just cause an explain() message
without a specific error message. By simply removing the relevant error check, the code now
handles this error more gracefully by printing an error message for all mandatory parameters.
It still prints the explain() message.
Signed-off-by: Kees van Reeuwijk <reeuwijk@few.vu.nl>
On openSUSE 12.2 (at least) xtables.h is not installed in the system-wide
include dir but in /usr/include/iptables-1.4.16.3/. This results in the
following build failure:
em_ipset.c:26:21: fatal error: xtables.h: No such file or directory
Other includers of xtables.h already call out to pkg-config
Fixes breakage with xtables API starting with version 1.4.10
Signed-off-by: Hasan Chowdhury <shemonc@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Rather than hard coding `pkg-config`, use ${PKG_CONFIG} so people can
override it to their specific version (like when cross-compiling).
This is the same way the upstream pkg-config code works.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Hi,
When compiling iproute2-3.6.0 on a host that doesn't have iptables available, I get the following error:
gcc -Wall -Wstrict-prototypes -O2 -I../include -DRESOLVE_HOSTNAMES
-DLIBDIR=\"/usr/lib\" -DCONFDIR=\"/etc/iproute2\" -D_GNU_SOURCE
-DCONFIG_GACT -DCONFIG_GACT_PROB -DYY_NO_INPUT -c -o em_ipset.o
em_ipset.c
em_ipset.c:26:21: fatal error: xtables.h: No such file or directory
Fixed by the following patch, which guards the building of em_ipset.o on
the presence of suitable headers.
Thanks,
Matt.
This ematch enables effective filtering of CAN frames (AF_CAN) based
on CAN identifiers with masking of compared bits. Implementation
utilizes bitmap based classification for standard frame format (SFF)
which is optimized for minimal overhead.
Signed-off-by: Rostislav Lisovy <lisovy@gmail.com>
example usage:
tc filter add dev $dev parent $id: basic match not ipset'(foobar src)' ..
also updates iproute2/ematch_map, else tc complains:
Error: Unable to find ematch "ipset" in /etc/iproute2/ematch_map
Please assign a unique ID to the ematch kind the suggested entry is:
8 ipset
when trying to use this ematch.
(text ematch (5) only exists in kernel, a vlan ematch (6) exists neither in
kernel nor userspace, but kernel headers define TCF_EM_VLAN == 6).
Since the get_rate() code incorrectly interpreted bare number, the
behavior is not the same as man page and comment described.
We need to change the man page and comment for compatible with the
existing usage by scripts.
Because we use the high 16 bits of tcm_info to pass prio value to
kernel, thus it's range would be [0, 0xffff], without validation
in tc when user pass a lager(>65535) priority, the actual priority
set in kernel would confuse the user.
So, add a validation to ensure prio in the range.
On current firstfrag filter, all non fragmented packets are matched.
firstfrag should check MF bit.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
The off of icmp_code is not 20 but 21. Also offmask should be 0 unless
nexthdr+ is specified.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Fair Queue Codel packet scheduler
Principles :
- Packets are classified (internal classifier or external) on flows.
- This is a Stochastic model (as we use a hash, several flows might
be hashed on same slot)
- Each flow has a CoDel managed queue.
- Flows are linked onto two (Round Robin) lists,
so that new flows have priority on old ones.
- For a given flow, packets are not reordered (CoDel uses a FIFO)
- head drops only.
- ECN capability is on by default.
- Very low memory footprint (64 bytes per flow)
tc qdisc ... fq_codel [ limit PACKETS ] [ flows number ]
[ target TIME ] [ interval TIME ] [ noecn ]
[ quantum BYTES ]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Kathleen Nichols <nichols@pollere.com>
Cc: Van Jacobson <van@pollere.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Changli Gao <xiaosuo@gmail.com>
An implementation of CoDel AQM, from Kathleen Nichols and Van Jacobson.
http://queue.acm.org/detail.cfm?id=2209336
This AQM main input is no longer queue size in bytes or packets, but the
delay packets stay in (FIFO) queue.
As we don't have infinite memory, we still can drop packets in enqueue()
in case of massive load, but mean of CoDel is to drop packets in
dequeue(), using a control law based on two simple parameters :
target : target sojourn time (default 5ms)
interval : width of moving time window (default 100ms)
Selected packets are dropped, unless ECN is enabled and packets can get
ECN mark instead.
Usage: tc qdisc ... codel [ limit PACKETS ] [ target TIME ]
[ interval TIME ] [ ecn ]
qdisc codel 10: parent 1:1 limit 2000p target 3.0ms interval 60.0ms ecn
Sent 13347099587 bytes 8815805 pkt (dropped 0, overlimits 0 requeues 0)
rate 202365Kbit 16708pps backlog 113550b 75p requeues 0
count 116 lastcount 98 ldelay 4.3ms dropping drop_next 816us
maxpacket 1514 ecn_mark 84399 drop_overlimit 0
CoDel must be seen as a base module, and should be used keeping in mind
there is still a FIFO queue. So a typical setup will probably need a
hierarchy of several qdiscs and packet classifiers to be able to meet
whatever constraints a user might have.
One possible example would be to use fq_codel, which combines Fair
Queueing and CoDel, in replacement of sfq / sfq_red.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Dave Taht <dave.taht@bufferbloat.net>
This patch provides support for marking packets with ECN instead of
dropping them with netem. This makes it possible to make use of the
netem ECN marking feature that was added recently to the kernel.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Define where is the are located the iproute2 config files.
Get rid of trailing slashes for paths in several file.
Signed-off-by: Christoph J. Thompson <cjsthompson@gmail.com>
As reported by Thomas Mühlgrabner <muehltom@cable.vol.at>
in http://bugs.debian.org/662979 :
When showing htb class configuration with "tc -iec class show",
the output for Mibit is actually the value for bit.
Example: configure a class with a ceil of 1000Mibit.
Output states 1048576000 Mibit.
The cause is missing parenteses in the display code of tc....
(Please also note that a lower value of 100Mibit will be displayed
as 102400 Kibit, which I think is kind of ugly.)
Reported-by: Thomas Mühlgrabner <muehltom@cable.vol.at>
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
LIBNETLINK will be defined in the main Makefile, so
both ../lib/libnetlink.a ../lib/libutil.a will be
automatically appended during linking. Otherwise
../lib/libnetlink.a ../lib/libutil.a will appear
twice during linking.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
(Resending patch since it looks like my earlier mail did not make it to
netdev).
netem reordering requires that the delay parameter be given. Currently, if no
delay is given, tc prints the error message but still installs the qdisc. Fix
this by printing the usage and failing cleanly.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
TCA_CHOKE_MAX_P permits to express high resolution RED probability.
tc qdisc add dev $DEV parent 1:1 handle 10: est 1sec 8sec choke \
limit 90 ecn min 10 max 30 probability 0.05 bandwidth 10Mbit
Before patch :
tc -s -d qdisc show dev eth3
qdisc ... limit 90p min 10p max 30p ecn ewma 3 Plog 19 Scell_log 13
After :
qdisc ... limit 90p min 10p max 30p ecn ewma 3 probability 0.05
Scell_log 13
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Adds an optional Random Early Detection on each SFQ flow queue.
Traditional SFQ limits count of packets, while RED permits to also
control number of bytes per flow, and adds ECN capability as well.
1) We dont handle the idle time management in this RED implementation,
since each 'new flow' begins with a null qavg. We really want to address
backlogged flows.
2) if headdrop is selected, we try to ecn mark first packet instead of
currently enqueued packet. This gives faster feedback for tcp flows
compared to traditional RED [ marking the last packet in queue ]
Example of use :
tc qdisc add dev $DEV parent 1:1 handle 10: est 1sec 4sec sfq \
limit 3000 headdrop flows 512 divisor 16384 \
redflowlimit 100000 min 8000 max 60000 probability 0.20 ecn
qdisc sfq 10: parent 1:1 limit 3000p quantum 1514b depth 127 headdrop
flows 512/16384 divisor 16384
ewma 6 min 8000b max 60000b probability 0.2 ecn
prob_mark 0 prob_mark_head 4876 prob_drop 6131
forced_mark 0 forced_mark_head 0 forced_drop 0
Sent 1175211782 bytes 777537 pkt (dropped 6131, overlimits 11007
requeues 0)
rate 99483Kbit 8219pps backlog 689392b 456p requeues 0
In this test, with 64 netperf TCP_STREAM sessions, 50% using ECN enabled
flows, we can see number of packets CE marked is smaller than number of
drops (for non ECN flows)
If same test is run, without RED, we can check backlog is much bigger.
qdisc sfq 10: parent 1:1 limit 3000p quantum 1514b depth 127 headdrop
flows 512/16384 divisor 16384
Sent 1148683617 bytes 795006 pkt (dropped 0, overlimits 0 requeues 0)
rate 98429Kbit 8521pps backlog 1221290b 841p requeues 0
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Enable Adaptative RED algo, using :
tc qdisc ... red limit BYTES ... adaptative ...
Support of high precision probability/max_p setting and reporting, with
support of old kernels.
With a new kernel, "Plog ..." is replaced in tc output by "probability
value" :
qdisc red 10: dev eth3 parent 1:1 limit 360Kb min 30Kb max 90Kb ecn ewma
5 probability 0.09 Scell_log 15
This patch add rate shaping as well as cell support. The link-rate can be
specified via rate options. Three optional arguments control the cell
knobs: packet-overhead, cell-size, cell-overhead. To ratelimit eth0 root
queue to 5kbit/s, with a 20 byte packet overhead, 100 byte cell size and
a 5 byte per cell overhead:
tc qdisc add dev eth0 root netem rate 5kbit 20 100 5
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Both rtnl_talk and rtnl_dump had a callback for handling portions
of netlink message that do not match the correct pid or seq.
But this callback was never used by any part of iproute2 so remove
it.
Add harddrop support (kernel support added a long time ago), and various
cleanups.
min BYTES, max BYTES are now optional and follow Sally Floyd's
recommendations.
By the way, our default 2% probability is a bit low, Sally recommends 10%.
Not a big deal if upcoming adaptative algo is deployed.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Documentation advises to set burst to (min+min+max)/(3*avpkt)
Let tc do this automatically if user doesnt provide burst himself.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
get_distribution() returns an int.
cppcheck reported:
[tc/q_netem.c:243]: (style) Checking if unsigned variable 'dist_size' is less than zero.
The mismatch actually rendered the error checking
after get_distribution() ineffective.
Signed-off-by: Thomas Jarosch <thomas.jarosch@intra2net.com>
This patch adds detailed documentation for HFSC scheduler. It roughly
follows HFSC paper, but tries to not rely too much on math side of things.
Post-paper/Linux specific subjects (timer resolution, ul service curve, etc.)
are also discussed.
I've read it many times over, but it's a lengthy chunk of text - so try
to be understanding in case I made some mistakes.
tc-hfsc(7): explains algorithm in detail (very long)
tc-hfsc(8): explains command line options briefly
tc(8): adds references to new man pages
Makefile: adds man7 directory to install target
q_hfsc.c: minimal help text changes, consistency with tc-hfsc(8)
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Building iproute2 in parallel might hit the race failure:
emp_ematch.l:2:30: fatal error: emp_ematch.yacc.h:
No such file or directory
make[1]: *** [emp_ematch.lex.o] Error 1
This is because we currently allow the yacc/lex files to generate and
compile in parallel. So add a simple dependency to make sure yacc has
finished before we attempt to compile the lex output.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
iptables/xtables apparently changed API again.... Now you need to pass
and extra parameter (orig_opts) which was not needed before.
Sprinkle some lovely pre-processor magic to be compatible with both older
and new versions. In the beginning of times XTABLES_VERSION_CODE didn't
exist. Then it was (0x10000 * major + 0x100 * minor + patch) when it was
first introduced (according to git), but now it's at 6...
Don't know what official iptables releases has defined it to over time.
Lets just hope none of the older versions with is has the define
higher then 6 is still around.... so only the "current" versioning
scheme is supported.... lets see how long this lasts now.
For the API change in xtables, see:
http://git.netfilter.org/cgi-bin/gitweb.cgi?p=iptables.git;a=commitdiff;h=600f38db82548a683775fd89b6e136673e924097
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
Add the iproute2 support for the ACT_CSUM action. Can be used as
following, certainly in conjunction with the ACT_PEDIT action (pedit):
# In order to DNAT (stateless) IPv4 packet from 192.168.1.100 to
# 0x12345678 (18.52.86.120), and update the IPv4 header checksum and
# the UDP checksum (the last one, only if the packet is UDP).
tc filter add eth0 prio 1 protocol ip parent ffff: \
u32 match ip src 192.168.1.100/32 flowid :1 \
action pedit munge offset 16 u32 set 0x12345678 \
pipe csum ip and udp
# In order to alter destination address of IPv6 TCP packets from fc00::1
# and correct the TCP checksum (nothing happened? except maybe for
# checksums in the TCP payload ...).
tc filter add eth0 prio 1 protocol ipv6 parent ffff: \
u32 match ip6 src fc00::1/128 match ip6 protocol 0x06 0xff flowid :1 \
action pedit munge offset 24 u32 set 0x12345678 \
pipe csum tcp
We can use rxhash to classify the traffic into flows. As rxhash maybe
supplied by NIC or RPS, it is cheaper.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Acked-by: Jamal Hadi Salim <hadi@cyberus.ca>
iptables dropped the xtables_set_revision() function around version 1.4.9,
so set the rev directly ourselves. This should be compatible back to the
original version m_xt itself is designed for.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Fixes problems with xtables based MARK target ("ipt" module).
When tc loads the "ipt" (xt) module it kept the symbols local,
this made loading of libxtables not find the required struct.
currently ipt/xt is the only tc action module.
iproute2 never seem to do dlclose.
hopefully the modules doesn't export more symbols then needed.
In this situation hopefully the RTLD_GLOBAL flag won't hurt us.
I've been using this patch in the Debian package of iproute for
the last 3 weeks and noone has complained.
( This fixes http://bugs.debian.org/584898 )
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
This patch adds ipv6 filter priority/traffic class function
static int parse_ip6_class(int *argc_p, char ***argv_p, struct tc_u32_sel *sel)
shifting filter value to 5th bit and ignoring "at" as header position
is exactly given.
Signed-off-by: Petr Lautrbach <plautrba@redhat.com>
The recent commit "iproute2: add option to build m_xt as a tc module"
(ab814d6355) looks like it wrongly included debug changes in the
install target. So drop the `echo` so the tc binary actually gets
installed again.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When building on an old environment, the flex generated
tc/emp_ematch.lex.c file would not compile. The error given was:
emp_ematch.lex.c:1686: error: expected â;â, â,â or â)â before numeric constant
The emp_ematch.l uses 'str' as a start symbol name, and flex would create
a '#define str 1' statement. This particular version of flex,
unfortunately, used 'str' as names of string variables in the generated
parser functions. This is line 1686 in the generated file:
YY_BUFFER_STATE ematch__scan_string (yyconst char * str )
This patch just substitutes 'str' for 'lexstr' in emp_ematch.l to avoid
the collision.
This will build the xt module (action ipt) of tc as a
shared object that is linked at runtime by tc if used,
rather then built into tc.
This is similar to how the atm qdisc support
is handled (q_atm.so).
Signed-off-by: Andreas Henriksson <andreas@xxxxxxxx>
Try to automatically detect iptables modules directory.
Make the configure script look for iptables modules.
This also makes it possible to specify it on the
command line while building via "make IPT_LIB_DIR=/foo/bar".
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
parsing a mark as a classid allows for acceptance of strange
informal input.
cheers,
jamal
commit aad0da6507ff8a95a63ed8e529c05f52be5b0e75
Author: Jamal Hadi Salim <hadi@cyberus.ca>
Date: Mon Feb 15 06:45:29 2010 -0500
skbedit: use get_u32 for parsing mark
get_u32 is the more appropriate parser for a mark.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
This adds the required changes to gain access to
the head drop classfull queuing discipline named
pfifo_head_drop. In difference to pfifo or pfifo_fast
this queuing discipline will drop the first packet
in the case of queue congestion. As a result the queue
contain always the freshest packets.
To replace the current a root queueing discipline
for eth0:
$ tc qdisc replace dev eth0 root pfifo_head_drop
And show statistics:
$ tc -s qdisc show dev eth0
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Since there aren't any targets that currently use this pattern rule, this
is more of a proactive fix.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This adds support for setting the skb mark.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Add a new cleaned up m_xt.c based on m_xt_old.c
The new m_xt.c has been updated to use the new names and new api
that xtables exposes in iptables 1.4.5.
All the old internal api cruft has also been dropped.
Additionally, a configure script test is added to check for
the new xtables api and set the TC_CONFIG_XT flag in Config.
(tc/Makefile already handles this flag in previous commit.)
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
Move the file and rename the configure flags.
The file is being kept around for iptables < 1.4.5 compatibility.
Signed-off-by: Andreas Henriksson <andreas@fatal.se>
The kernel takes a lack of options as indication that the fw classifier
should operate in compatibility mode, where marks are mapped directly to
classids.
Commit e22b42a (tc mask patch) broke this by adding an empty TCA_OPTIONS
attribute even if no handle is specified. Restore the old behaviour.
Signed-off-by: Patrick McHardy <kaber@trash.net>
A bunch of source files look like they're copy & pasted from other files,
and some include header files that they don't actually need. Since dlfcn
has very specific usage (and is a pain on a static-only system), drop it
where it isn't really needed.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The iptables code supports a "no shared libs" mode where it can be used
without requiring dlfcn related functionality. This adds similar support
to iproute2 so that it can easily be used on systems like nommu Linux (but
obviously with a few limitations -- no dynamic plugins).
Rather than modify every location that uses dlfcn.h, I hooked the dlfcn.h
header with stub functions when shared library support is disabled. Then
symbol lookup is done via a local static lookup table (which is generated
automatically at build time) so that internal symbols can be found.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sometimes while dividing bandwidth by classes it is useful to see how some
specific class doing things live.
Which my simple patch it is possible to do
watch -n1 "tc -s -d class show dev eth0.2022 classid 1:1520"
and to get live statistics, how packets queued or dropped, and how much
bandwidth used (if estimator defined) for specific class.
Signed-off-by: Denys Fedoryshchenko <denys@visp.net.lb>
This change was forgotten by Stephen in the last release
Signed-off-by: Denys Fedoryschenko <denys@visp.net.lb>
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Many thanks to Yevgeny Kosarzhevsky <yevg@pisem.net> for reporting
and a lot of testing
Thanks to Jan Engelhardt <jengelh@medozas.de> for a lot of advice
Thanks to Denys Fedoryschenko <denys@visp.net.lb> for some sample
code that he tried and thanks to Andreas Henriksson <andreas@fatal.se>
(who maintains iproute2 on debian) for the persistent followup.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Original from: Alexander Duyck <alexander.h.duyck@intel.com>
A bug was found in which the memory for the tc_skbedit struct was being
used uninitialized to 0. Alternative version of original fix
using initializer rather than memset.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
1)optind according iptables sources have to be set to 0. If it is set to 1, in
batch it will mess up things. Also in iptables sources i notice that ->tflags
and ->used need to be reset.
2)Since target->t = fw_calloc(1, size); allocated memory in function build_st,
it have to be freed at the end, or in batch we will have memory leak. TODO:
Probably it must be freed in all "return -1" cases in parse_ipt after
build_st. About this i am not sure, up to Stephen.
3)new_name was malloc'ed, but not freed
Add support for multiq qdisc
This patch adds the ability to configure the multiq qdisc. Since the qdisc does not require any input it will pull the number of bands directly from the device that it is added to the root of.
usage: tc qdisc add dev <DEV> root handle <HANDLE> multiq
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provides ability to edit queue_mapping field
Provides ability to edit priority field
usage: action skbedit [queue_mapping QUEUE_MAPPING] [priority PRIORITY]
at least one option must be select, or both at the same time
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hello Rafael Almeida.
I noticed your patch adding DESTDIR support in the latest iproute2 release.
Much appreciated! Soon the debian packages might be able to move to actually
using "make install" rather then it's own installation procedure when
building packages. I've noticed something that will break though....
Debian packages usually sets DESTDIR=debian/tmp/ and packages the contents
of that directory as if it where the root file system. This will break
the /usr/lib/{tc,ip}/ module loading, because they DESTDIR (/usr) will be
/whatever-the-build-path-was/debian/tmp/lib/{tc,ip}/.
I beleive others usually call this the LIBDIR to make the separation between
DISTDIR being the (possibly temporary) place things are put when build is
done, and LIBDIR (and others) are used for actual runtime paths.
I'm attaching a patch that I think fixes this, but would be really happy if
you could have a look at to verify I'm not screwing something up.
--
Regards,
Andreas Henriksson
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Patch adds generic size table that is similiar to rate table, with
difference that size table stores link layer packet size.
Based on patch by Patrick McHardy
http://marc.info/?l=linux-netdev&m=115201979221729&w=2
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
After changing the DESTDIR the installated binaries have some issues
due to hard coded paths. For example, using distributions on NetEm
would segfault.
I've changed iplink.c and tc_util.c so they are now aware of DESTDIR.
Along with that change I needed to change the main Makefile so it
defines the DESTDIR macro when calling gcc.
I also changed the paths so that during the installation sbin, etc,
share and lib directories are created directly inside of the DESTDIR,
instead of creating a usr directory inside that. That's the behaviour
of most packages out there, so I think most users will be expecting
that to happen.
> # tc filter show dev eth1 | grep 4:29:d1
> filter parent 1: protocol ip pref 5 u32 fh 4:29:d1 order 209 key ht 4
> bkt 29 flowid 1:b7aa
>
> # tc filter del dev eth1 parent 1: pref 5 handle 4:29:d1 u32
> RTNETLINK answers: Invalid argument
> We have an error talking to the kernel
>
> after rollback to package"sys-apps/iproute2-2.6.24.20080108" all
> deleted normal...
The current iproute version uses "protocol all" by default
if its not specified. This is actually only useful for creating
new filters, on deletion an unset protocol is treated as wildcard.
And last for now ..
cheers,
jamal
[PATCH 3/3] [TC/U32] Infrastructure for pretty printing
This patch makes it easy to add pretty printers of different protocols.
For starters it makes use of ipv4 and raw printers.
Add more later ...
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
makes protocol accessible ..
cheers,
jamal
[PATCH 2/3] [TC/FILTERS] Expose the filter protocol
Expose the filter protocol so it can be used by underlying
classifiers when they need it.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Don't break scripts that depend on previous offset/value format.
Introduce a new -pretty flag for decoding, and (*gasp*) document
the formatting arguments.
commit c504ffd627ac211eebf5ed34ef0fbfd7f1dbb347
Author: Patrick McHardy <kaber@trash.net>
Date: Wed Mar 26 07:38:43 2008 +0100
[IPROUTE]: Fix classifier help
The new check whether the user has specified a protocol makes
"ip filter <type> help" fails with "protocol is required".
This could be fixed by moving it further down, but a more user-friendly
way it to simply use ETH_P_ALL as default if nothing is specified.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Introducing the function that does the ATM cell alignment, and
modifying tc_calc_rtable() to use this based upon a linklayer
parameter.
Modified from original to use constants from atm.h and
fix all the usages of rtable in same patch.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
For police, implement overhead parameter parsing.
The change is ABI (Application Binary Interface) backward compatible
with older kernels, but will first have effect from kernel 2.6.24.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
For CBQ, implement overhead parameter parsing.
The change is ABI (Application Binary Interface) backward compatible
with older kernels, but will first have effect from kernel 2.6.24.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
Change CBQ to use matches() function instead of strcmp().
This resembels the usage in other parse functions, and allows
partial command parameter matching.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
For TBF, implement overhead parameter parsing.
The change is ABI (Application Binary Interface) backward compatible
with older kernels, but will first have effect from kernel 2.6.24.
Signed-off-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Stephen Hemminger <stephen.hemminger@vyatta.com>
