To be installed with the other man pages.
Fixes: d57639a475 ("tc/act_tunnel: Introduce ip tunnel action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Amir Vadai <amir@vadai.me>
Replace vlan_eth_type with vlan_ethtype.
Fixes: 745d917260 ("tc: flower: Introduce vlan support")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Enhance tunnel key action parameters by adding destination UDP port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Enhance IP tunnel parameters by adding destination UDP port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Adds support to configure BPF programs as nexthop actions via the LWT
framework.
Example:
ip route add 192.168.253.2/32 \
encap bpf out obj lwt_len_hist_kern.o section len_hist \
dev veth0
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Support matching on ICMP type and code.
Example usage:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 protocol ip parent ffff: flower \
indev eth0 ip_proto icmp type 8 code 0 action drop
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128 code 0 action drop
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Now that we made the BPF loader generic as a library, reuse it
for loading XDP programs as well. This basically adds a minimal
start of a facility for iproute2 to load XDP programs. There
currently only exists the xdp1_user.c sample code in the kernel
tree that sets up netlink directly and an iovisor/bcc front-end.
Since we have all the necessary infrastructure in place already
from tc side, we can just reuse its loader back-end and thus
facilitate migration and usability among the two for people
familiar with tc/bpf already. Sharing maps, performing tail calls,
etc works the same way as with tc. Naturally, once kernel
configuration API evolves, we will extend new features for XDP
here as well, resp. extend dumping of related netlink attributes.
Minimal example:
clang -target bpf -O2 -Wall -c prog.c -o prog.o
ip [-force] link set dev em1 xdp obj prog.o # attaching
ip [-d] link # dumping
ip link set dev em1 xdp off # detaching
For the dump, intention is that in the first line for each ip
link entry, we'll see "xdp" to indicate that this device has an
XDP program attached. Once we dump some more useful information
via netlink (digest, etc), idea is that 'ip -d link' will then
display additional relevant program information below the "link/
ether [...]" output line for such devices, for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
This is needed for some HWs to do proper macthing and steering.
Possible values are none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add missing usage help for devlink dev eswitch subcommand.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Remove references to eth_type and ether_type (spelling error) in
the tc flower manpage.
Also correct formatting of boldface text with whitespace.
Cc: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This action could be used before redirecting packets to a shared tunnel
device, or when redirecting packets arriving from a such a device.
The 'unset' action is optional. It is used to explicitly unset the
metadata created by the tunnel device during decap. If not used, the
metadata will be released automatically by the kernel.
The 'set' operation, will set the metadata with the specified values for
the encap.
For example, the following flower filter will forward all ICMP packets
destined to 11.11.11.2 through the shared vxlan device 'vxlan0'. Before
redirecting, a metadata for the vxlan tunnel is created using the
tunnel_key action and it's arguments:
$ tc filter add dev net0 protocol ip parent ffff: \
flower \
ip_proto 1 \
dst_ip 11.11.11.2 \
action tunnel_key set \
src_ip 11.11.0.1 \
dst_ip 11.11.0.2 \
id 11 \
action mirred egress redirect dev vxlan0
Signed-off-by: Amir Vadai <amir@vadai.me>
Introduce classifying by metadata extracted by the tunnel device.
Outer header fields - source/dest ip and tunnel id, are extracted from
the metadata when classifying.
For example, the following will add a filter on the ingress Qdisc of shared
vxlan device named 'vxlan0'. To forward packets with outer src ip
11.11.0.2, dst ip 11.11.0.1 and tunnel id 11. The packets will be
forwarded to tap device 'vnet0':
$ tc filter add dev vxlan0 protocol ip parent ffff: \
flower \
enc_src_ip 11.11.0.2 \
enc_dst_ip 11.11.0.1 \
enc_key_id 11 \
dst_ip 11.11.11.1 \
action mirred egress redirect dev vnet0
Signed-off-by: Amir Vadai <amir@vadai.me>
This is needed for some HWs to do proper macthing and steering.
Possible values are none, link, network, transport.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add missing usage help for devlink dev eswitch subcommand.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Cc: steweg@gmail.com
v5:
- rebase and fix checkpatch
v4:
- add MACADDR_SET support
- skip FLAG_UNICAST / FLAG_UNICAST_ALL as this is not upstream
- fix man page
This makes use of the sctp_diag interface recently added to the kernel.
Joint work with Xin Long who provided the PoC implementation which I
merely polished up a bit.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Remove left over usage from removal of eth_type argument.
Fixes: 488b41d020 ('tc: flower no need to specify the ethertype')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
So far, only the 'egress' direction was implemented.
Allow specifying 'ingress' as the direction packet appears on the target
interface.
For example, this takes incoming 802.1q frames on veth0 and redirects
them for input on dummy0:
# tc filter add dev veth0 parent ffff: pref 1 protocol 802.1q basic \
action mirred ingress redirect dev dummy0
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Recently a new per-port flag was added which controls the flooding of
unknown multicast, this patch adds support for controlling it via iproute2.
It also updates the man pages with information about the new flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Add support for controling hardware offload using (now standard)
skip_sw and skip_hw flags in cls_bpf.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Adjusting iproute2 utility to support new macvlan link type mode called
"source".
Example of commands that can be applied:
ip link add link eth0 name macvlan0 type macvlan mode source
ip link set link dev macvlan0 type macvlan macaddr add 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr del 00:11:11:11:11:11
ip link set link dev macvlan0 type macvlan macaddr flush
ip -details link show dev macvlan0
Based on previous work of Stefan Gula <steweg@gmail.com>
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
Cc: steweg@gmail.com
Introduce a new API that exposes a list of vlans per VF (IFLA_VF_VLAN_LIST),
giving the ability for user-space application to specify it for the VF as
an option to support 802.1ad (VST QinQ).
We introduce struct vf_vlan_info, which extends struct vf_vlan and adds
an optional VF VLAN proto parameter.
Default VLAN-protocol is 802.1Q.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older kernel versions.
Suitable ip link tool command examples:
- Set vf vlan protocol 802.1ad (S-TAG)
ip link set eth0 vf 1 vlan 100 proto 802.1ad
- Set vf vlan S-TAG and vlan C-TAG (VST QinQ)
ip link set eth0 vf 1 vlan 100 proto 802.1ad vlan 30 proto 802.1Q
- Set vf to VST (802.1Q) mode
ip link set eth0 vf 1 vlan 100 proto 802.1Q
- Or by omitting the new parameter (backward compatible)
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
The 'vlan modify' action allows to replace an existing 802.1q tag
according to user provided settings.
It accepts same arguments as the 'vlan push' action.
For example, this replaces vid 6 with vid 5:
# tc filter add dev veth0 parent ffff: pref 1 protocol 802.1q \
basic match 'meta(vlan mask 0xfff eq 6)' \
action vlan modify id 5 continue
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Hi,
On Thu, Sep 08, 2016 at 11:59:55AM +0200, Michal Kubecek wrote:
> On Thu, Sep 01, 2016 at 09:04:54AM -0700, Stephen Hemminger wrote:
> > On Tue, 30 Aug 2016 17:32:52 -0700
> > Iskren Chernev <iskren@imo.im> wrote:
> >
> > > From 416f45b62f33017d19a9b14e7b0179807c993cbe Mon Sep 17 00:00:00 2001
> > > From: Iskren Chernev <iskren@imo.im>
> > > Date: Tue, 30 Aug 2016 17:08:54 -0700
> > > Subject: [PATCH bug-fix] iproute: fix documentation for ip rule scan order
> > >
> > > ---
> > > man/man8/ip-rule.8 | 2 +-
> > > 1 file changed, 1 insertion(+), 1 deletion(-)
> > >
> > > diff --git a/man/man8/ip-rule.8 b/man/man8/ip-rule.8
> > > index 1774ae3..3508d80 100644
> > > --- a/man/man8/ip-rule.8
> > > +++ b/man/man8/ip-rule.8
> > > @@ -93,7 +93,7 @@ Each policy routing rule consists of a
> > > .B selector
> > > and an
> > > .B action predicate.
> > > -The RPDB is scanned in order of decreasing priority. The selector
> > > +The RPDB is scanned in order of increasing priority. The selector
> > > of each rule is applied to {source address, destination address,
> > > incoming
> > > interface, tos, fwmark} and, if the selector matches the packet,
> > > the action is performed. The action predicate may return with success.
> > > --
> > > 2.4.5
> >
> > Applied
>
> I'm sorry I didn't notice before but this just reverts the change done
> by commit 4957250166 ("iproute2: clarification of various man8 pages").
> IMHO the problem is that both versions are equally confusing as the word
> "priority" can be understood in two different senses.
>
> How about more explicit formulation, e.g.
>
> ... in order of decreasing logical priority (i.e. increasing numeric
> values).
>
> Would that be better?
Looks like the real issue is missing definition of priority. What about
this:
use get_be64() in place of get_u64() when parsing input 'sci' parameter,
so that 'sci' can be entered using network byte order regardless the
endianness of target system; use ntohll() when printing out 'sci'. While
at it, improve documentation of 'sci' in ip-link.8.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
remove hardcoded base 10 parsing of 'port' parameter, update man page
and fix usage() functions as well. Fix misleading line in man page that
theoretically allowed specifying 'port' keyword right after 'sci' keyword.
Provide documentation of 'address' parameter in man pages and in usage()
functions as well.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
The current vlan push action supports only vid and protocol options.
Add priority option.
Example script that adds vlan push action with vid and priority:
tc filter add dev veth0 protocol ip parent ffff: \
flower \
indev veth0 \
action vlan push id 100 priority 5
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
