Recently a new temp router port mode was added and with it the dumped
information was extended similar to how mdb entries were done. This
patch adds support to dump the new information by using the "-s" switch.
Example:
$ bridge -d -s mdb show
dev br0 port eth1 grp ff02::1:ffbf:5716 temp 234.39
dev br0 port eth1 grp 239.0.0.2 temp 97.17
dev br0 port eth1 grp 239.0.0.3 temp 105.36
router ports on br0: eth1 0.00 permanent
router ports on br0: eth2 254.87 temp
It also updates the bridge man page.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Recently support was added to the kernel to be able to add more per-mdb
entry attributes via standard netlink attributes of type MDBA_MDB_EATTR_.
This patch adds support to iproute2 to parse and output these
attributes. The first exported attribute is the mdb "timer" value which
is shown only when the "-s" iproute2 arg is used.
Example:
$ bridge -s mdb show
dev br0 port eth1 grp 239.0.0.11 permanent 0.00
dev br0 port eth1 grp 239.0.0.10 temp 244.15
dev br0 port eth1 grp 239.0.0.1 temp 245.21
dev br0 port eth1 grp 239.0.0.5 temp 246.43
dev br0 port eth2 grp 239.0.0.5 temp 248.44
dev br0 port eth1 grp 239.0.0.2 temp 245.32
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Add netlink support bridge port attributes such as cost, priority, state
and flags. This also adds support for HW mode such as VEPA or VEB.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Recent kernel patches added support for VLAN filtering on the bridge.
This functionality allows one to turn a basic bridge into a VLAN bridge,
where VLANs dicatate packet forwarding and header transformation.
To configure the VLANs on the bridge and its ports a new command is
added to the 'bridge' utility.
# bridge vlan add dev eth0 vid 10 pvid untagged brdev
# bridge vlan add
# bridge vlan delete dev eth0 vid 10
# bridge vlan show
This command supports the following flags:
master - peform the operation on the software bridge device. This is
the default behavior.
self - perform the operation on the hardware associated with the port.
This flag is required when the device is the bridge device and
the configuration is desired on the bridge device itself (not
one of the ports).
pvid - Set the PVID (port vlan id) for a given port. Any untagged
frames arriving on the port will be assigned to this vlan.
untagged - Sets the egress policy of for a given vlan. Default port
egress policy is tagged. Set this flag if you wish traffic
associated with this VLAN to exit the port untagged.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
This patch implements `bridge monitor mdb`.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Cong Wang <amwang@redhat.com>
Sample output:
# ./bridge/bridge mdb show dev br0
bridge br0 port eth1 group 224.8.8.9
bridge br0 port eth0 group 224.8.8.8
# ./bridge/bridge -d mdb show dev br0
bridge br0 port eth1 group 224.8.8.9
bridge br0 port eth0 group 224.8.8.8
router ports on br0: eth0
Signed-off-by: Cong Wang <amwang@redhat.com>
