This commit adds support to expose the following inet socket options:
-- recverr
-- is_icsk
-- freebind
-- hdrincl
-- mc_loop
-- transparent
-- mc_all
-- nodefrag
-- bind_address_no_port
-- recverr_rfc4884
-- defer_connect
with the option --inet-sockopt. The individual option is only shown
when set.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch adds support for recently
added link IFLA_PROTO_DOWN_REASON attribute.
IFLA_PROTO_DOWN_REASON enumerates reasons
for the already existing IFLA_PROTO_DOWN link
attribute.
$ cat /etc/iproute2/protodown_reasons.d/r.conf
0 mlag
1 evpn
2 vrrp
3 psecurity
$ ip link set dev vx10 protodown on protodown_reason vrrp on
$ip link show dev vx10
14: vx10: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether f2:32:28:b8:35:ff brd ff:ff:ff:ff:ff:ff protodown on
protodown_reason <vrrp>
$ip -p -j link show dev vx10
[ {
<snip>
"proto_down": true,
"proto_down_reason": [ "vrrp" ]
} ]
$ip link set dev vx10 protodown_reason mlag on
$ip link show dev vx10
14: vx10: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether f2:32:28:b8:35:ff brd ff:ff:ff:ff:ff:ff protodown on
protodown_reason <mlag,vrrp>
$ip -p -j link show dev vx10
[ {
<snip>
"proto_down": true,
"protodown_reason": [ "mlag","vrrp" ]
} ]
$ip -p -j link show dev vx10
$ip link set dev vx10 protodown off protodown_reason vrrp off
Error: Cannot clear protodown, active reasons.
$ip link set dev vx10 protodown off protodown_reason mlag off
$
Note: for somereason the json and non-json key for protodown
are different (protodown and proto_down). I have kept the
same for protodown reason for consistency (protodown_reason and
proto_down_reason).
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
PRP support requires a proto parameter which is 0 for hsr and 1 for
prp. Default is hsr and is backward compatible.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Document the new supported criteria of auto mode. Examples:
$ rdma statistic qp set link mlx5_2/1 auto pid on
$ rdma statistic qp set link mlx5_2/1 auto pid,type on
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Ido Kalir <idok@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
This flag allows to create SA where sequence number can cycle in
outbound packets if set.
Signed-off-by: Petr Vaněk <pv@excello.cz>
Signed-off-by: David Ahern <dsahern@kernel.org>
In most of cases a user wants to see only the dynamic mac addresses
in the fdb output. But currently the 'fdb show' displays tons of
various self entries, those only waste the output without any useful
goal.
New option 'dynamic' for 'show' and 'get' commands forces display
only relevant records.
Signed-off-by: Anton Danilov <littlesmilingcloud@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
To improve the usability better use case-insensitive pattern-matching
in ifstat, nstat and ss tools.
Signed-off-by: Anton Danilov <littlesmilingcloud@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The XFRMA_IF_ID attribute is set in policies for them to be
associated with an XFRM interface (4.19+).
Add support for getting/deleting policies with this attribute.
For supporting 'deleteall' the XFRMA_IF_ID attribute needs to be
explicitly copied.
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
In commit aed63ae1ac ("ip xfrm: support setting/printing XFRMA_IF_ID attribute in states/policies")
I added the ability to set/print the xfrm interface ID without updating
the man page.
Fixes: aed63ae1ac ("ip xfrm: support setting/printing XFRMA_IF_ID attribute in states/policies")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
When setting a policer to a trap group, a value of "0" will unbind the
currently bound policer from the group.
The behavior is intentional and tested in kernel selftests, so document
it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add the new "mpls" keyword that can be used to match MPLS fields in
arbitrary Label Stack Entries.
LSEs are introduced by the "lse" keyword and followed by LSE options:
"depth", "label", "tc", "bos" and "ttl". The depth is manadtory, the
other options are optionals.
For example, the following filter drops MPLS packets having two labels,
where the first label is 21 and has TTL 64 and the second label is 22:
$ tc filter add dev ethX ingress proto mpls_uc flower mpls \
lse depth 1 label 21 ttl 64 \
lse depth 2 label 22 bos 1 \
action drop
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Bareudp devices provide a generic L3 encapsulation for tunnelling
different protocols like MPLS, IP, NSH, etc. inside a UDP tunnel.
This patch is based on original work from Martin Varghese:
https://lore.kernel.org/netdev/1570532361-15163-1-git-send-email-martinvarghesenokia@gmail.com/
Examples:
- ip link add dev bareudp0 type bareudp dstport 6635 ethertype mpls_uc
This creates a bareudp tunnel device which tunnels L3 traffic with
ethertype 0x8847 (unicast MPLS traffic). The destination port of the
UDP header will be set to 6635. The device will listen on UDP port 6635
to receive traffic.
- ip link add dev bareudp0 type bareudp dstport 6635 ethertype ipv4 multiproto
Same as the MPLS example, but for IPv4. The "multiproto" keyword allows
the device to also tunnel IPv6 traffic.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Before can be possible show only all qeueue disciplines on an interface.
There wasn't a way to get the qdisc info by handle or parent, only full
dump of the disciplines with a following grep/sed usage.
Now new and old options work as expected to filter a qdisc by handle or
parent.
Full syntax of the qdisc show command:
tc qdisc { show | list } [ dev STRING ] [ QDISC_ID ] [ invisible ]
QDISC_ID := { root | ingress | handle QHANDLE | parent CLASSID }
This change doesn't require any changes in the kernel.
Signed-off-by: Anton Danilov <littlesmilingcloud@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Use a single font macro for a single argument.
Remove unnecessary quotes for a single-font macro.
Join two lines into one.
The output of "nroff" and "groff" is unchanged.
Signed-off-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Use a single-font macro for one argument.
Remove unnecessary quotes for a single font macro.
Join some lines into one.
The output of "nroff" and "groff" is unchanged, except for a font
change in two lines.
Signed-off-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Use a single-font macro for a single argument
Signed-off-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Use a single-font macro for a single argument.
Signed-off-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Typeset section numbers in roman font, see man-pages(7).
###
Details:
Output is from: test-groff -b -mandoc -T utf8 -rF0 -t -w w -z
[ "test-groff" is a developmental version of "groff" ]
<./man/man3/libnetlink.3>:53 (macro BR): only 1 argument, but more are expected
<./man/man3/libnetlink.3>:132 (macro BR): only 1 argument, but more are expected
<./man/man3/libnetlink.3>:134 (macro BR): only 1 argument, but more are expected
<./man/man3/libnetlink.3>:197 (macro BR): only 1 argument, but more are expected
<./man/man3/libnetlink.3>:198 (macro BR): only 1 argument, but more are expected
Signed-off-by: Bjarni Ingi Gislason <bjarniig@rhi.hi.is>
Add 'raw' argument to get the resource in raw format.
When RDMA_NLDEV_ATTR_RES_RAW is set in the netlink message,
then the resource fields are in raw format, print it as byte array.
Example:
$rdma res show qp link rocep0s12f0/1 lqpn 1137 -j -r
[{"ifindex":7,"ifname":"mlx5_1","port":1,
"data":[0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,...]}]
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
The "early_drop" qevent matches packets that have been early-dropped. The
"mark" qevent matches packets that have been ECN-marked.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
This patch adds support to assign a nexthop group
id to an fdb entry.
$bridge fdb add 02:02:00:00:00:13 dev vx10 nhid 102 self
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch adds support to add and delete
ecmp nexthops of type fdb. Such nexthops can
be linked to vxlan fdb entries.
$ip nexthop add id 12 via 172.16.1.2 fdb
$ip nexthop add id 13 via 172.16.1.3 fdb
$ip nexthop add id 102 group 12/13 fdb
$bridge fdb add 02:02:00:00:00:13 dev vx10 nhid 102 self
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
optimistic DAD is controllable via sysctl for an interface
or all interfaces on the system. This would affect addresses
added by the kernel only.
Recent kernels, however, have enabled support for adding optimistic
address via userspace. This plumbs that support.
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch introduces two new features: obtaining cgroup information and
filtering sockets by cgroups. These features work based on cgroup v2 ID
field in the socket (kernel should be compiled with CONFIG_SOCK_CGROUP_DATA).
Cgroup information can be obtained by specifying --cgroup flag and now contains
only pathname. For faster pathname lookups cgroup cache is implemented. This
cache is filled on ss startup and missed entries are resolved and saved
on the fly.
Cgroup filter extends EXPRESSION and allows to specify cgroup pathname
(relative or absolute) to obtain sockets attached only to this cgroup.
Filter syntax: ss [ cgroup PATHNAME ]
Examples:
ss -a cgroup /sys/fs/cgroup/unified (or ss -a cgroup .)
ss -a cgroup /sys/fs/cgroup/unified/cgroup1 (or ss -a cgroup cgroup1)
v2:
- style fixes (David Ahern)
Signed-off-by: Dmitry Yakunin <zeil@yandex-team.ru>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch is to add TCA_FLOWER_KEY_ENC_OPTS_ERSPAN's parse and
print to implement erspan options support in m_tunnel_key, like
Commit 56155d4df8 ("tc: f_flower: add geneve option match
support to flower") for geneve options support.
Option is expressed as version:index:dir:hwid, dir and hwid will
be parsed when version is 2, while index will be parsed when
version is 1. erspan doesn't support multiple options.
With this patch, users can add and dump erspan options like:
# ip link add name erspan1 type erspan external
# tc qdisc add dev erspan1 ingress
# tc filter add dev erspan1 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
erspan_opts 1:2:0:0/1:255:0:0 \
ip_proto udp \
action mirred egress redirect dev eth1
# tc -s filter show dev erspan1 parent ffff:
filter protocol ip pref 49152 flower chain 0 handle 0x1
eth_type ipv4
ip_proto udp
enc_dst_ip 10.0.99.193
enc_src_ip 10.0.99.192
enc_key_id 11
erspan_opts 1:2:0:0/1:255:0:0
not_in_hw
action order 1: mirred (Egress Redirect to device eth1) stolen
index 1 ref 1 bind 1
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
v1->v2:
- no change.
v2->v3:
- no change.
v3->v4:
- keep the same format between input and output, json and non json.
- print version, index, dir and hwid as uint.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch is to add TCA_FLOWER_KEY_ENC_OPTS_VXLAN's parse and
print to implement vxlan options support in m_tunnel_key, like
Commit 56155d4df8 ("tc: f_flower: add geneve option match
support to flower") for geneve options support.
Option is expressed a 32bit number for gbp only, and vxlan
doesn't support multiple options.
With this patch, users can add and dump vxlan options like:
# ip link add name vxlan1 type vxlan dstport 0 external
# tc qdisc add dev vxlan1 ingress
# tc filter add dev vxlan1 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
vxlan_opts 65793/4008635966 \
ip_proto udp \
action mirred egress redirect dev eth1
# tc -s filter show dev vxlan1 parent ffff:
filter protocol ip pref 49152 flower chain 0 handle 0x1
eth_type ipv4
ip_proto udp
enc_dst_ip 10.0.99.193
enc_src_ip 10.0.99.192
enc_key_id 11
vxlan_opts 65793/4008635966
not_in_hw
action order 1: mirred (Egress Redirect to device eth1) stolen
index 3 ref 1 bind 1
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
v1->v2:
- get_u32 with base = 0 for gbp.
v2->v3:
- implement proper JSON array for opts.
v3->v4:
- keep the same format between input and output, json and non json.
- print gbp as uint.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch is to add TCA_TUNNEL_KEY_ENC_OPTS_ERSPAN's parse and
print to implement erspan options support in m_tunnel_key, like
Commit 6217917a38 ("tc: m_tunnel_key: Add tunnel option support
to act_tunnel_key") for geneve options support.
Option is expressed as version:index:dir:hwid, dir and hwid will
be parsed when version is 2, while index will be parsed when
version is 1. erspan doesn't support multiple options.
With this patch, users can add and dump erspan options like:
# ip link add name erspan1 type erspan external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
erspan_opts 1:2:0:0 \
action mirred egress redirect dev erspan1
# tc -s filter show dev eth0 parent ffff:
filter protocol ip pref 49151 flower chain 0 handle 0x1
indev eth0
eth_type ipv4
ip_proto udp
not_in_hw
action order 1: tunnel_key set
src_ip 10.0.99.192
dst_ip 10.0.99.193
key_id 11
dst_port 6081
erspan_opts 1:2:0:0
csum pipe
index 2 ref 1 bind 1
...
v1->v2:
- no change.
v2->v3:
- no change.
v3->v4:
- keep the same format between input and output, json and non json.
- print version, index, dir and hwid as uint.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch is to add TCA_TUNNEL_KEY_ENC_OPTS_VXLAN's parse and
print to implement vxlan options support in m_tunnel_key, like
Commit 6217917a38 ("tc: m_tunnel_key: Add tunnel option support
to act_tunnel_key") for geneve options support.
Option is expressed a 32bit number for gbp only, and vxlan
doesn't support multiple options.
With this patch, users can add and dump vxlan options like:
# ip link add name vxlan1 type vxlan dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
vxlan_opts 65793 \
action mirred egress redirect dev vxlan1
# tc -s filter show dev eth0 parent ffff:
filter protocol ip pref 49152 flower chain 0 handle 0x1
indev eth0
eth_type ipv4
ip_proto udp
not_in_hw
action order 1: tunnel_key set
src_ip 10.0.99.192
dst_ip 10.0.99.193
key_id 11
dst_port 6081
vxlan_opts 65793
...
v1->v2:
- get_u32 with base = 0 for gbp.
- use to print_unint("0x%x") to print gbp.
v2->v3:
- implement proper JSON array for opts.
v3->v4:
- keep the same format between input and output, json and non json.
- print gbp as uint.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
The Type I ERSPAN frame format is based on the barebones
IP + GRE(4-byte) encapsulation on top of the raw mirrored frame.
Both type I and II use 0x88BE as protocol type. Unlike type II
and III, no sequence number or key is required.
To creat a type I erspan tunnel device:
$ ip link add dev erspan11 type erspan \
local 172.16.1.100 remote 172.16.1.200 \
erspan_ver 0
CC: Dmitriy Andreyevskiy <dandreye@cisco.com>
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
While at it, additionally fix a mandoc warning in mptcp.8
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch adds support for configuring offload mode upon MACsec
device creation.
If offload mode is not specified, then netlink attribute is not
added. Default behavior on the kernel side in this case is
backward-compatible (offloading is disabled by default).
Example:
$ ip link add link eth0 macsec0 type macsec port 11 encrypt on offload mac
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch enables MAC HW offload usage in iproute, since MACSec
implementation supports it now.
Signed-off-by: Mark Starovoytov <mstarovoitov@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Root_block is also called root port guard, document it.
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Document that guard disable the port and how to reenable it
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This option is useful for Wifi bridge but need some tweak.
Document it from kernel patches documentation
Signed-off-by: Bastien Roucariès <rouca@debian.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
These can be configured to different paths. Reflect that in the
generated documentation.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Prepare for adding new variable substitutions. Unify the sed rules while
we're at it, since there's no need to write this out 4 times.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add support for configuring auto_dump attribute per reporter.
With this attribute, one can indicate whether the devlink kernel core
should execute automatic dump on error.
The change will be reflected in show, set and man commands.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Fix description for htb class prio parameter to indicate it's not
mandatory.
Signed-off-by: Benjamin Lee <ben@b1c1l1.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add description for htb class parameter quantum.
Signed-off-by: Benjamin Lee <ben@b1c1l1.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add description for htb qdisc parameter r2q.
Signed-off-by: Benjamin Lee <ben@b1c1l1.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This sentence predates addition of extended pedit for IPv6 packets.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Describe a way to update just the DSCP and just the ECN part of the
dsfield. That is useful on its own, but also it shows how retain works.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Support keywords dsfield, traffic_class and tos in the IPv6 context.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Fix error from make check.
n-old.tmac: <standard input>: line 86: 'R' is a string (producing the registered sign), not a macro.
Error in tc-actions.8
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
DEVLINK_ATTR_ESWITCH_ENCAP_MODE netlink attribute carries enum. But the
code assumes bool value. Fix this by treating the encap mode in the same
way as other eswitch mode attributes, switching from "enable"/"disable"
to "basic"/"none", according to the enum. Maintain the backward
compatibility to allow user to pass "enable"/"disable" too. Also to be
in-sync with the rest of the "mode" commands, rename to "encap-mode".
Adjust the help and man page accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Fix the help and man page of "devlink health set" command to be aligned
with the rest of helps and man pages.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add ability to associate a policer with a trap group. The policer can be
unbound by using the 'nopolicer' keyword. In which case, the value
encoded in the 'DEVLINK_ATTR_TRAP_POLICER_ID' attribute will be '0'.
This is consistent with ip-link 'nomaster' keyword and the 'IFLA_MASTER'
attribute.
Example:
# devlink trap group set netdevsim/netdevsim10 group l3_drops policer 2
# devlink -jp trap group show netdevsim/netdevsim10 group l3_drops
{
"trap_group": {
"netdevsim/netdevsim10": [ {
"name": "l3_drops",
"generic": true,
"policer": 2
} ]
}
}
# devlink trap group set netdevsim/netdevsim10 group l3_drops nopolicer
# devlink -jp trap group show netdevsim/netdevsim10 group l3_drops
{
"trap_group": {
"netdevsim/netdevsim10": [ {
"name": "l3_drops",
"generic": true
} ]
}
}
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
The trap policer set command allows the user to set the parameters of
the packet trap policer, such as rate and burst size. Example:
# devlink trap policer set netdevsim/netdevsim10 policer 1 rate 1000 burst 32
The trap policer show command allows the user to get the current
parameters of an individual policer or a dump of all policers in case
one is not specified. When '-s' is specified the policer's statistics
are shown. Example:
# devlink -jps trap policer show netdevsim/netdevsim10 policer 1
{
"trap_policer": {
"netdevsim/netdevsim10": [ {
"policer": 1,
"rate": 1000,
"burst": 32,
"stats": {
"rx": {
"dropped": 53
}
}
} ]
}
}
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
When multiple bridges are present, 'bridge link show' diplays ports
for all bridges. Make this clear in the command description, and
point out the user to the ip command to display ports for a specific
bridge.
Reported-by: Marc Muehlfeld <mmuehlfe@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Recognize the new configuration option of the RED Qdisc, "nodrop". Add
support for passing flags through TCA_RED_FLAGS, and use it when passing
TC_RED_NODROP flag.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Introduce support for per-action hw stats type config.
This patch allows user to specify one of the following types of HW
stats for added action:
immediate - queried during dump time
delayed - polled from HW periodically or sent by HW in async manner
disabled - no stats needed
Note that if "hw_stats" option is not passed, user does not care about
the type, just expects any type of stats.
Examples:
$ tc filter add dev enp0s16np28 ingress proto ip handle 1 pref 1 flower skip_sw dst_ip 192.168.1.1 action drop hw_stats disabled
$ tc -s filter show dev enp0s16np28 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
skip_sw
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 7 sec used 2 sec
Action statistics:
Sent 0 bytes 0 pkt (dropped 0, overlimits 0 requeues 0)
backlog 0b 0p requeues 0
hw_stats disabled
$ tc filter add dev enp0s16np28 ingress proto ip handle 1 pref 1 flower skip_sw dst_ip 192.168.1.1 action drop hw_stats immediate
$ tc -s filter show dev enp0s16np28 ingress
filter protocol ip pref 1 flower chain 0
filter protocol ip pref 1 flower chain 0 handle 0x1
eth_type ipv4
dst_ip 192.168.1.1
skip_sw
in_hw in_hw_count 2
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 11 sec used 4 sec
Action statistics:
Sent 102 bytes 1 pkt (dropped 1, overlimits 0 requeues 0)
Sent software 0 bytes 0 pkt
Sent hardware 102 bytes 1 pkt
backlog 0b 0p requeues 0
hw_stats immediate
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Add a description of the `ip macsec offload` command used to select the
offloading mode on a macsec interface when the underlying device
supports it.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Add description for filters on rdma statistics show command.
Also add a filter description on the help message of the command.
Additionally, fix some whitespace issue in the man page.
Reported-by: Zhaojuan Guo <zguo@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add resource subcommand in the OBJECT section and a short
description for it.
Reported-by: Zhaojuan Guo <zguo@redhat.com>
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add description to the vrf subcommand and a reference to the
dedicated man page.
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Add support for devlink health error recovery status monitoring.
Update devlink-monitor man page accordingly.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch adds support for the FQ-PIE packet Scheduler
Principles:
- Packets are classified on flows.
- This is a Stochastic model (as we use a hash, several flows might
be hashed to the same slot)
- Each flow has a PIE managed queue.
- Flows are linked onto two (Round Robin) lists,
so that new flows have priority on old ones.
- For a given flow, packets are not reordered.
- Drops during enqueue only.
- ECN capability is off by default.
- ECN threshold (if ECN is enabled) is at 10% by default.
- Uses timestamps to calculate queue delay by default.
Usage:
tc qdisc ... fq_pie [ limit PACKETS ] [ flows NUMBER ]
[ target TIME ] [ tupdate TIME ]
[ alpha NUMBER ] [ beta NUMBER ]
[ quantum BYTES ] [ memory_limit BYTES ]
[ ecn_prob PERCENTAGE ] [ [no]ecn ]
[ [no]bytemode ] [ [no_]dq_rate_estimator ]
defaults:
limit: 10240 packets, flows: 1024
target: 15 ms, tupdate: 15 ms (in jiffies)
alpha: 1/8, beta : 5/4
quantum: device MTU, memory_limit: 32 Mb
ecnprob: 10%, ecn: off
bytemode: off, dq_rate_estimator: off
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Sachin D. Patil <sdp.sachin@gmail.com>
Signed-off-by: V. Saicharan <vsaicharan1998@gmail.com>
Signed-off-by: Mohit Bhasi <mohitbhasi1998@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
While at it, convert xfrm_xfrma_print and xfrm_encap_type_parse to use
the UAPI macros for encap_type as suggested by David Ahern, and add the
UAPI udp.h header (sync'd from ipsec-next to get the TCP_ENCAP_ESPINTCP
definition).
Co-developed-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David Ahern <dsahern@gmail.com>
Enable proper JSON output for the PIE Qdisc.
Use sprint_time() to print the value of tc_pie_xstats->delay.
Use the long double format specifier to print tc_pie_xstats->prob.
Also, fix the indentation in the oneline output of statistics and update
the man page to reflect this change.
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Enable proper JSON output for the FQ Qdisc.
Use the "KEY VALUE" format for oneline output of statistics instead of
"VALUE KEY", and remove unnecessary commas from the output.
Use sprint_size() to print size values in fq_print_opt().
Use sprint_time64() to print time values in fq_print_xstats().
Also, update the man page to reflect the changes in the output format.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
"SRC VNI" is only one argument and should appear as such. Moreover, this
argument to the src_vni option is documented under three forms: "SRC_VNI",
"SRC VNI" and "VNI" in different places. Consistenly use the simplest form,
"VNI".
Fixes: c5b176e5ba ("bridge: fdb: add support for src_vni option")
Signed-off-by: Benjamin Poirier <bpoirier@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
PIE now uses per packet timestamps to calculate queuing
delay. The average dequeue rate based queue delay
calculation is now made optional. This patch adds the option
to enable or disable the use of Little's law to calculate
queuing delay.
Signed-off-by: Gautam Ramakrishnan <gautamramk@gmail.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: Mohit P. Tahiliani <tahiliani@nitk.edu.in>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
tc-ematch.8 was missing the description of canid() ematch rule, so document
this.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Extended match rules are currently supported by basic, flow and cgroup
filters, so update the man page.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
PPP devices can be moved to different network namespaces. The feature
was added by commit 79c441ae505c ("ppp: implement x-netns support")
in Linux 4.3.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Implement setting and printing of action flags with single available flag
value "no_percpu" that translates to kernel UAPI TCA_ACT_FLAGS value
TCA_ACT_FLAGS_NO_PERCPU_STATS. Update man page with information regarding
usage of action flags.
Example usage:
# tc actions add action gact drop no_percpu
# sudo tc actions list action gact
total acts 1
action order 0: gact action drop
random type none pass val 0
index 1 ref 1 bind 0
no_percpu
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Implement addition/deletion of lists of properties, currently
alternative ifnames. Also extent the ip link show command to list them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Add document of accessing the MR counters into
the rdma-statistic man pages.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
This is a follow up of the commit eaefb07804 ("ipnetns: enable to dump
nsid conversion table").
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This is a follow up of the commit ebe3ce2fcc ("ipnetns: parse nsid as a
signed integer").
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
By default, all devices are listed, not only the default group.
Signed-off-by: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: Romain Bellan <romain.bellan@wifirst.fr>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The ability to specify the source adresse for 'encap ip' / 'encap ip6'
was added in commit 94a8722f2f but the man
page was not updated.
Also fixes a missing page in ip-route.8.in.
Signed-off-by: Damien Robert <damien.olivier.robert+git@gmail.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Extend existing devlink reload command by adding option "netns" by which
user can instruct kernel to reload the devlink instance into specified
network namespace.
Example:
$ ip netns add testns1
$ devlink dev reload netdevsim/netdevsim10 netns testns1
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
