Add capability to ip-monitor to listen and dump nexthop messages.
Since the nexthop group = 32 which exceeds the max groups bit
field, 2 separate flags are needed - one that defaults on to indicate
nexthop group is joined by default and a second that indicates a
specific selection by the user (e.g, ip mon nexthop route).
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Every tool in the iproute2 package have one or more function to show
an help message to the user. Some of these functions print the help
line by line with a series of printf call, e.g. ip/xfrm_state.c does
60 fprintf calls.
If we group all the calls to a single one and just concatenate strings,
we save a lot of libc calls and thus object size. The size difference
of the compiled binaries calculated with bloat-o-meter is:
ip/ip:
add/remove: 0/0 grow/shrink: 5/15 up/down: 103/-4796 (-4693)
Total: Before=672591, After=667898, chg -0.70%
ip/rtmon:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-54 (-54)
Total: Before=48879, After=48825, chg -0.11%
tc/tc:
add/remove: 0/2 grow/shrink: 31/10 up/down: 882/-6133 (-5251)
Total: Before=351912, After=346661, chg -1.49%
bridge/bridge:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-459 (-459)
Total: Before=70502, After=70043, chg -0.65%
misc/lnstat:
add/remove: 0/1 grow/shrink: 1/0 up/down: 48/-486 (-438)
Total: Before=9960, After=9522, chg -4.40%
tipc/tipc:
add/remove: 0/0 grow/shrink: 1/1 up/down: 18/-62 (-44)
Total: Before=79182, After=79138, chg -0.06%
While at it, indent some strings which were starting at column 0,
and use tabs where possible, to have a consistent style across helps.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
No function, filter, or print function uses the sockaddr_nl arg,
so just drop it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Add support for MPLS netconf to ip monitor and ip netconf commands.
Changes to header files not included as those are typically pulled
in my a header sync with the kernel.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
The calling of netns_map_init() before command parsing introduced
a performance issue with large number of namespaces.
As commands such as add, del and exec do not need to iterate through
/var/run/netns it would be good not no build the cache before executing
these commands.
Example:
unpatched:
time seq 1 1000 | xargs -n 1 ip netns add
real 0m16.832s
user 0m1.350s
sys 0m15.029s
patched:
time seq 1 1000 | xargs -n 1 ip netns add
real 0m3.859s
user 0m0.132s
sys 0m3.205s
Signed-off-by: Anton Aksola <aakso@iki.fi>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
'ip monitor all' is broken on older kernels.
This patch fixes 'ip monitor all' to match
'all' and not 'all-nsid'.
It moves parsing arg 'all-nsid' to after parsing
'all'.
Before:
$ip monitor all
NETLINK_LISTEN_ALL_NSID: Protocol not available
After:
$ip monitor all
[NEIGH]Deleted 10.0.0.1 dev eth1 lladdr c4:54:44:4f:b2:dd STALE
Fixes: 449b824ad1 ("ipmonitor: allows to monitor in several netns")
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
With this patch, it's now possible to listen in all netns that have an nsid
assigned into the netns where the socket is opened.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Two commands are added:
- ip netns list-id
- ip monitor nsid
A cache is also added to remember the association between the iproute2 netns
name (from /var/run/netns/) and the nsid.
To avoid interfering with the rth socket, a new rtnl socket (rtnsh) is used to
get nsid (we may send rtnl request during listing on rth).
Example:
$ ip netns list-id
nsid 0 (iproute2 netns name: foo)
$ ip monitor nsid
Deleted nsid 0 (iproute2 netns name: foo)
nsid 16 (iproute2 netns name: bar)
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
- Pull in the uapi mpls.h
- Update rtnetlink.h to include the mpls rtnetlink notification multicast group.
- Define AF_MPLS in utils.h if it is not defined from elsewhere
as is done with AF_DECnet
The address syntax for multiple mpls labels is a complete invention.
When I looked there seemed to be no wide spread convention for talking
about an mpls label stack in text for. Sometimes people did:
"{ Label1, Label2, Label3 }", sometimes people would do:
"[ label3, label2, label1 ]", and most of the time label
stacks were not explicitly shown at all.
The syntax I wound up using, so it would not have spaces and so it
would visually distinct from other kinds of addresses is.
label1/label2/label3 Where label1 is the label at the top of the label
stack and label3 is the label at the bottom on the label stack.
When there is a single label this matches what seems to be convention
with other tools. Just print out the numeric value of the mpls label.
The netlink protocol for labels uses the on the wire format for a
label stack. The ttl and traffic class are expected to be 0. Using
the on the wire format is common and what happens with other address
types. BGP when passing label stacks also uses this technique with the
exception that the ttl byte is not included making each label in a BGP
label stack 3 bytes instead of 4.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The issue was observed when IPv6 router broadcasted NDUSEROPT
messages which are not handled by monitor and caused printing
'Timestamps' w/o message because such kind of rtnl messages is not
handled by monitor.
As 'ip monitor' by default subscribes to the all mcast rtnl groups except
RTGRP_TC then all messages of these rtnl groups which are not handled by
monitor may cause such issues.
Fixed by subscribing by default to rtnl mcast groups which are
supported by 'ip monitor'.
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
In case if unknown message was handled then it will be displayed as:
Unknown message: type=0x00000044(68) flags=0x00000000(0) len=0x0000004c(76)
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
This is ugly fix but solves the case when timestamp
or banner-label is printed before the cloned route will be skipped
by iproute filter which filters out all cached routes by default.
In such case timestamp will be printed twice:
Timestamp: Thu Sep 4 19:46:59 2014 457933 usec
Timestamp: Thu Sep 4 19:47:07 2014 977970 usec
10.3.5.1 dev wlp3s0 lladdr XX:XX:XX:XX:XX:XX STALE
Signed-off-by: Vadim Kochan <vadim4j@gmail.com>
Prefix labelling is currently only activated when monitoring "all"
objects. However, the output can still be confusing when monitoring
more than 1 object, so add an option to always print prefix labels.
Signed-off-by: Martin Schwenke <martin@meltin.net>
mroute was using /proc/net/ip_mr_[vif|cache] to display mroute entries. Hence,
only RT_TABLE_DEFAULT was displayed and only IPv4.
With rtnetlink, it is possible to display all tables for IPv4 and IPv6. The output
format is kept. Also, like before the patch, statistics are displayed when user specify
the '-s' argument.
The patch also adds the support of 'ip monitor mroute', which is now possible.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
This patch adds a new flag to iproute2 for vxlan devices to enable
DOVE features. It also adds support for L2 and L3 switch lookup miss
netlink messages to "ip monitor".
Changes since v2: fix merge conflict
Changes since v1:
- split "dove" flag into separate feature flags:
- "proxy" for ARP reduction
- "rsc" for route short circuiting
- "l2miss" for L2 switch miss notifications
- "l3miss" for L3 switch miss notifications
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
This patch allows to manage ip6 tunnels via the interface ip link.
The syntax for parameters is the same that 'ip -6 tunnel'.
It also allows to display tunnels parameters with 'ip -details link' or
'ip -details monitor link'.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Hello Stephen and netdev people!
Currently you can configure "equalize" and it looks all fine and dandy.
The kernel has the interface defined, but apparently there's never actually
been any implementation for it (only a never merged patch in the 2.4 era).
I'm suggesting to drop the code to give any potential users of this feature
the benefit of receiving a proper error message. I see it unlikely that
this will be implemented in the near future, but if it ever happens
reviving the iproute2 side should be as easy as git revert this patch.
For more details see http://bugs.debian.org/149897
Regards,
Andreas Henriksson
This patch adds prefix lables for "ip monitor all" command to simplfy
understanding of the output.
Signed-off-by: Varun Chandramohan <varunc@linux.vnet.ibm.com>
This patch adds exclusive support to enable monitoring
neighbour table entries in ip command.
Signed-off-by: Varun Chandramohan <varunc@linux.vnet.ibm.com>
cheers,
jamal
[ALL] update rest to use nl_mgrp
Signed-off-by: J Hadi Salim <hadi@cyberus.ca>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
