Instead of rolling a custom on-off printer, use the one added to utils.c.
Note that _print_onoff() has an extra parameter for a JSON-specific flag
name. However that argument is not used, and never was. Therefore when
moving over to print_on_off(), drop this argument.
Signed-off-by: Petr Machata <me@pmachata.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Invoke parse_on_off() from bridge_slave_parse_on_off() instead of
hand-rolling one. Exit on failure, because the invarg that was ivoked here
before would.
Signed-off-by: Petr Machata <me@pmachata.org>
Signed-off-by: David Ahern <dsahern@gmail.com>
Every tool in the iproute2 package have one or more function to show
an help message to the user. Some of these functions print the help
line by line with a series of printf call, e.g. ip/xfrm_state.c does
60 fprintf calls.
If we group all the calls to a single one and just concatenate strings,
we save a lot of libc calls and thus object size. The size difference
of the compiled binaries calculated with bloat-o-meter is:
ip/ip:
add/remove: 0/0 grow/shrink: 5/15 up/down: 103/-4796 (-4693)
Total: Before=672591, After=667898, chg -0.70%
ip/rtmon:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-54 (-54)
Total: Before=48879, After=48825, chg -0.11%
tc/tc:
add/remove: 0/2 grow/shrink: 31/10 up/down: 882/-6133 (-5251)
Total: Before=351912, After=346661, chg -1.49%
bridge/bridge:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-459 (-459)
Total: Before=70502, After=70043, chg -0.65%
misc/lnstat:
add/remove: 0/1 grow/shrink: 1/0 up/down: 48/-486 (-438)
Total: Before=9960, After=9522, chg -4.40%
tipc/tipc:
add/remove: 0/0 grow/shrink: 1/1 up/down: 18/-62 (-44)
Total: Before=79182, After=79138, chg -0.06%
While at it, indent some strings which were starting at column 0,
and use tabs where possible, to have a consistent style across helps.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This adds configuration for the IFLA_BRPORT_MCAST_TO_UCAST flag that
allows multicast packets to be replicated as unicast packets.
Signed-off-by: Tobias Jungel <tobias.jungel@bisdn.de>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
The argument to print_0xhex is converted to unsigned long long
so the format string give for normal printout has to be some
variant of %llx. Otherwise, bogus values will be printed on
32 bit platforms.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This patch adds support for the new backup port option that can be set
on a bridge port. If the port's carrier goes down all of the traffic
gets redirected to the configured backup port. We add the following new
arguments:
$ ip link set dev brport type bridge_slave backup_port brport2
$ ip link set dev brport type bridge_slave nobackup_port
$ bridge link set dev brport backup_port brport2
$ bridge link set dev brport nobackup_port
The man pages are updated respectively.
Also 2 minor style adjustments:
- add missing space to bridge man page's state argument
- use lower starting case for vlan_tunnel in ip-link man page (to be
consistent with the rest)
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This patch adds support for the new isolated port option which, if set,
would allow the isolated ports to communicate only with non-isolated
ports and the bridge device. The option can be set via the bridge or ip
link type bridge_slave commands, e.g.:
$ ip link set dev eth0 type bridge_slave isolated on
$ bridge link set dev eth0 isolated on
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
In gre/gre6 for non-JSON output 0x%x format is used: use print_0xhex()
to get the same value for JSON.
Get rid of custom _print_hex() in bridge slave code: print_0xhex() can
be used perfectly.
Break long print_uint() with long argument list to fit into 80 columns.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
This config maps to IFLA_BRPORT_VLAN_TUNNEL bridge port netlink
flag attribute. This flag enables vlan to tunnel mapping on a bridge
port. It is off by default.
set vlan_tunnel attribute on bridge port vxlan0:
$ip link set dev vxlan0 type bridge_slave vlan_tunnel on
$ip link set dev vxlan0 type bridge_slave vlan_tunnel off
or via bridge command
$bridge link set dev vxlan0 vlan_tunnel on
$bridge link set dev vxlan0 vlan_tunnel off
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Add neigh_suppress to the type help and document it in ip-link's man page.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
This patch adds the iproute2 support for getting and setting the
per-port group_fwd_mask. It also tries to resolve the value into a more
human friendly format by printing the known protocols instead of only
the raw value.
The man page is also updated with the new option.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
neigh suppression can be used to suppress arp and nd flood
to bridge ports. It maps to the recently added
kernel support for bridge port flag IFLA_BRPORT_NEIGH_SUPPRESS.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
This patch adds support to the bridge_slave link type for displaying
xstats by reusing the previously added bridge xstats callbacks.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
This patch implements support for the IFLA_BRPORT_FLUSH attribute
in iproute2 so it can flush bridge slave's fdb dynamic entries.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Recently a new per-port flag was added which controls the flooding of
unknown multicast, this patch adds support for controlling it via iproute2.
It also updates the man pages with information about the new flag.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
The original bond/bridge/vrf and slaves use same id, which make people
confused. Use bond/bridge/vrf_slave as id name will make code more clear.
Acked-by: Phil Sutter <psutter@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Add support to be able to view and change IFLA_BRPORT_MULTICAST_ROUTER port
attribute.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Export all the read-only values that get returned about a bridge port
such as the timers, the ids, designated_port and cost,
topology_change_ack and config_pending. For the bridge ids the
br_dump_bridge_id function is exported from iplink_bridge.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
