mirror of
https://git.proxmox.com/git/mirror_frr
synced 2025-11-03 23:47:16 +00:00
fd5006896f
This command allows the user to change to default reference bandwidth for cost calculations. The default value is 100 Mbps. With a default bandwidth of 10 MBps, the default cost becomes 10. Those values are consistent with OSPFv2. [DL: resolved conflicts in vty command additions & docs] Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
103 lines
3.1 KiB
Plaintext
103 lines
3.1 KiB
Plaintext
|
|
Zebra OSPF daemon for IPv6 network
|
|
|
|
2003/08/18
|
|
|
|
README for newer code is not yet. General usage should remain
|
|
the same. For further usage, see command helps by typing '?'
|
|
in vty, and then imagin ! ;p) Previous README contents follows.
|
|
|
|
Zebra OSPF daemon for IPv6 network
|
|
|
|
2001/12/20
|
|
|
|
Zebra OSPF6d is OSPF version 3 daemon which is specified by
|
|
"OSPF for IPv6" (RFC 2740).
|
|
|
|
*** NOTE ***
|
|
Zebra ospf6d is in development yet. It may lack some functionalities,
|
|
and may have some bugs. Use the latest version from the anoncvs
|
|
repository (http://www.zebra.org/cvs.html) !
|
|
|
|
This file README is like memo yet, so please feel free to ask
|
|
<yasu@sfc.wide.ad.jp> by E-mail. Patches will be appriciated.
|
|
|
|
ospf6d's vty port was default to 2606/tcp.
|
|
Use commands below.
|
|
|
|
VIEW NODE:
|
|
show ipv6 ospf6
|
|
To see Router-ID, uptime of ospf6d, some statistics.
|
|
|
|
show ipv6 ospf6 database ...
|
|
This command shows LSA database. You can specify
|
|
LS-type/LS-ID/Advertising-Router of LSAs. '*' is recognized.
|
|
|
|
show ipv6 ospf6 interface ...
|
|
To see the status of the OSPF interface, and the configuration
|
|
like interface costs.
|
|
|
|
show ipv6 ospf6 neighbor ...
|
|
Shows state of neighbors and choosed (Backup) DR on the I/F.
|
|
|
|
show ipv6 ospf6 route (X::X)
|
|
This command shows internal routing table of the ospf6d.
|
|
Routes not calculated by OSPFv3 (like connected routes)
|
|
are not shown. If Address is specified (X::X), shows the route
|
|
that the address matches.
|
|
|
|
show ipv6 ospf6 route redistribute (X::X)
|
|
Shows the routes advertised as AS-External routes by the router
|
|
itself. If Address is specified (X::X), shows the route
|
|
that the address matches.
|
|
|
|
CONFIG NODE:
|
|
interface NAME
|
|
To enter INTERFACE NODE
|
|
|
|
router ospf6 ...
|
|
To enter OSPF6 NODE
|
|
|
|
INTERFACE NODE:
|
|
ipv6 ospf6 cost COST
|
|
Sets the interface's output cost. Depends on interface bandwidth by default.
|
|
|
|
ipv6 ospf6 hello-interval HELLOINTERVAL
|
|
Sets the interface's Hello Interval. default 10
|
|
|
|
ipv6 ospf6 dead-interval DEADINTERVAL
|
|
Sets the interface's Router Dead Interval. default 40
|
|
|
|
ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL
|
|
Sets the interface's Rxmt Interval. default 5
|
|
|
|
ipv6 ospf6 priority PRIORITY
|
|
Sets the interface's Router Priority. default 1
|
|
|
|
ipv6 ospf6 transmit-delay TRANSMITDELAY
|
|
Sets the interface's Inf-Trans-Delay. default 1
|
|
|
|
OSPF6 NODE:
|
|
router-id A.B.C.D
|
|
Sets the router's Router-ID
|
|
|
|
interface NAME area AREA
|
|
Binds interface to specified Area, and start
|
|
sending OSPFv3 packets.
|
|
|
|
auto-cost reference-bandwidth COST
|
|
Sets the reference bandwidth for cost calculations, where this
|
|
bandwidth is considered equivalent to an OSPF cost of 1, specified
|
|
in Mbits/s. The default is 100Mbit/s (i.e. a link of bandwidth
|
|
100Mbit/s or higher will have a cost of 1. Cost of lower bandwidth
|
|
links will be scaled with reference to this cost). This
|
|
configuration setting MUST be consistent across all routers within
|
|
the OSPF domain.
|
|
|
|
Sample configuration is in ospf6d.conf.sample.
|
|
|
|
--
|
|
Yasuhiro Ohara <yasu@sfc.wide.ad.jp>
|
|
Kunihiro Ishiguro <kunihiro@zebra.org>
|
|
|