When unconfiguring certain commands in ospf, you can
run into situations where we attempt to read beyond
the end of a argv[] vector created. On certain platforms
this will crash it.
Ticket: CM-14090
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
All of the autogenerated macros in lib/route_types.pl are now called
FRR_* instead of QUAGGA_*.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Several places have paths and names that can change hardcoded, e.g. the
package name and the /var/run path. This fixes a few of them, there's
still some to do.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This replaces Quagga -> FRR in most configure.ac settings as well as
a handful of preprocessor macros in the source code.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
If we fail to set any socket's buffer size, try again with a smaller value
and keep going until it succeeds. This is better than just giving up or,
even worse, abort the creation of a socket (ospf6d and ripd).
Fix broken ospf6d on FreeBSD.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This reverts commit b7fe4141, which introduced a logic where the OSPF
send buffer size was dynamically updated to reflect the maximum MTU
of the OSPF enabled interfaces (this was done to make ospfd work with
interfaces configured for jumbo frames).
Since commit a78d75b0, this is not necessary anymore because
ospf_sock_init() now sets the OSPF send buffer size to a very high value
(8MB). Also, the previous logic was broken because it didn't account
for run-time interface MTU changes.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When nbr->t_inactivity is not active, and
you do a show json over the neighbor it
will crash ospfd. Fix the code so it
prints out -1 when the timer is inactive.
Ticket:CM-13835
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
(cherry picked from commit 78d8fcb9623ab4d9cebf6187a451448e056a84bf)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When doing a show command under ospf, if
not using json we would have a small memory
leak in show_ip_ospf_common.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit 50750712b1ac8364e290c67782eaf371025dc59e)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-13712
(cherry picked from commit 367b138748e894bbfaae36d1cf7c90eafebfebc9)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
We can't use if_lookup_prefix() in rip_update_process() because this
function uses prefix_cmp() internally to try matching an interface
address to a static neighbor's address.
Since prefix_cmp() tries to match exact prefixes, if_lookup_prefix()
was always returning NULL.
What we really need here is to use prefix_match(), which checks if
one prefix includes the other (e.g. one /24 interface including a /32
static neighbor's address). The fix then is to replace the call to
if_lookup_prefix() and use if_lookup_address() instead, which uses
prefix_match() internally.
Fixes IxANVL RIP test 17.1
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When ospf RI commands are entered and we have not turned
on the feature, gracefully tell the user that there is
no going forward.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If ospf mpls-te has not been turned on via a 'mpls-te on'
dissallow other mpls-te commands from being silently accepted
and ignored.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
Consolidate the routemap initialization into one
function.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
If a command is put into the VIEW_NODE, it is going into the
ENABLE_NODE as well. This is especially true for show commands.
As such if a command is in both consolidate it down to VIEW_NODE.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This patch improves zebra,ripd,ripngd,ospfd and bgpd so that they can
make use of 32-bit route tags in the case of zebra,ospf,bgp or 16-bit
route-tags in the case of ripd,ripngd.
It is based on the following patch:
commit d25764028829a3a30cdbabe85f32408a63cccadf
Author: Paul Jakma <paul.jakma@hpe.com>
Date: Fri Jul 1 14:23:45 2016 +0100
*: Widen width of Zserv routing tag field.
But also contains the changes which make this actually useful for all
the daemons.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Problem reported that no peers are displayed when the command "show
ip ospf neighbor detail all" is entered. Determined that the problem
was actually that the function only displayed NBMA peers, and since
we rarely (if ever) define NBMA peers, nothing is normally displayed.
Changed the code to display both NBMA and non-NBMA peers, in both the
up and down state. Manual testing attached to the jira ticket.
Ticket: CM-5878
Signed-off-by: Don Slice
Reviewed-by: Daniel Walton
* zclient.c: prefix length on router-id and interface address add
messages not sanity checked. fix.
* */*_zebra.c: Prefix length on zebra route read was not checked, and
clients use it to write to storage. An evil zebra could overflow
client structures by sending overly long prefixlen.
Prompted by discussions with:
Donald Sharp <sharpd@cumulusnetworks.com>
Since recently zebra uses only the ZEBRA_REDISTRIBUTE_* messages
to advertise redistributed routes to its clientes. Now the old
ZEBRA_IPV*_ROUTE_* messages are only used for client->zebra communication.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The new TE functions will always print out a warning
that TE has not been configured on an interface. This
should be a debug not a warn.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This is a rather large mechanical commit that splits up the memory types
defined in lib/memtypes.c and distributes them into *_memory.[ch] files
in the individual daemons.
The zebra change is slightly annoying because there is no nice place to
put the #include "zebra_memory.h" statement.
bgpd, ospf6d, isisd and some tests were reusing MTYPEs defined in the
library for its own use. This is bad practice and would break when the
memtype are made static.
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
[CF: rebased for cmaster-next]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Move over to the new allocation counting added in the previous commit.
(This commit is mostly mechanical.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Entering 'show ip ospf interface json' causes ospf
to crash.
Entering 'show ip ospf interface <intf> json' causes
ospf to crash if intf has no neighbors on the otherside
Modify the code to not crash in these cases.
Ticket: CM-12776
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Entering 'show ip ospf interface json' causes ospf
to crash.
Entering 'show ip ospf interface <intf> json' causes
ospf to crash if intf has no neighbors on the otherside
Modify the code to not crash in these cases.
Ticket: CM-12776
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
This is an implementation of RFC4970 (Router Information) and
RFC5088 (PCE Capabilities announcement)
* ospfd/Makefile.am: Add new file ospf_ri.c and ospf_ri.h
* ospfd/ospf_opaque.c: Add new Router Capabilities code point
* ospfd/ospf_ri.[c,h]: Implementation of RFC4970 & RFC5088
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
NOTE: I am squashing several commits together because they
do not independently compile and we need this ability to
do any type of sane testing on the patches. Since this
series builds together I am doing this. -DBS
This new structure is the basis to get new link parameters for
Traffic Engineering from Zebra/interface layer to OSPFD and ISISD
for the support of Traffic Engineering
* lib/if.[c,h]: link parameters struture and get/set functions
* lib/command.[c,h]: creation of a new link-node
* lib/zclient.[c,h]: modification to the ZBUS message to convey the
link parameters structure
* lib/zebra.h: New ZBUS message
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add support for IEEE 754 format
* lib/stream.[c,h]: Add stream_get{f,d} and stream_put{f,d}) demux and muxers to
safely convert between big-endian IEEE-754 single and double binary
format, as used in IETF RFCs, and C99. Implementation depends on host
using __STDC_IEC_559__, which should be everything we care about. Should
correctly error out otherwise.
* lib/network.[c,h]: Add ntohf and htonf converter
* lib/memtypes.c: Add new memeory type for Traffic Engineering support
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add link parameters support to Zebra
* zebra/interface.c:
- Add new link-params CLI commands
- Add new functions to set/get link parameters for interface
* zebra/redistribute.[c,h]: Add new function to propagate link parameters
to routing daemon (essentially OSPFD and ISISD) for Traffic Engineering.
* zebra/redistribute_null.c: Add new function
zebra_interface_parameters_update()
* zebra/zserv.[c,h]: Add new functions to send link parameters
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add support of new link-params CLI to vtysh
In vtysh_config.c/vtysh_config_parse_line(), it is not possible to continue
to use the ordered version for adding line i.e. config_add_line_uniq() to print
Interface CLI commands as it completely break the new LINK_PARAMS_NODE.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Update Traffic Engineering support for OSPFD
These patches update original code to RFC3630 (OSPF-TE) and add support of
RFC5392 (Inter-AS v2) & RFC7471 (TE metric extensions) and partial support
of RFC6827 (ASON - GMPLS).
* ospfd/ospf_dump.[c,h]: Add new dump functions for Traffic Engineering
* ospfd/ospf_opaque.[c,h]: Add new TLV code points for RFC5392
* ospfd/ospf_packet.c: Update checking of OSPF_OPTION
* ospfd/ospf_vty.[c,h]: Update ospf_str2area_id
* ospfd/ospf_zebra.c: Add new function ospf_interface_link_params() to get
Link Parameters information from the interface to populate Traffic Engineering
metrics
* ospfd/ospfd.[c,h]: Update OSPF_OPTION flags (T -> MT and new DN)
* ospfd/ospf_te.[c,h]: Major modifications to update the code to new
link parameters structure and new RFCs
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
tmp
Use the 'enum nexthop_types_t' instead of
the zebra.h #defines. And remove code from
zebra.h that does not belong there.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Use with interface command:
interface ppp0
ip ospf area 0.0.0.0
This will enable OSPF on ppp0 with area 0.0.0.0
Remove with "no ip ospf area"
* ospf_vty.c: add "ip ospf area (A.B.C.D|<0-4294967295>)" interface command
* ospfd.c: (ospf_interface_{un,}set) new helper function to enable/disable
OSPF on a specific interface.
(ospf_if_update) 2 possible paths now to deal with interface updates.
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
[DL: this restores the tree to deccaf9...]
This reverts commit e723861da1.
The code is from Joakim Tjernlund; this is just to fix the history (and
attribution) of it. The last commit will restore the exact same tree
state.
THIS COMMIT WILL PROBABLY NOT COMPILE.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Remove from ospf the HAVE_OSPF_TE define and just always have
ospf traffic engineering.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Tested-by: NetDEF CI System <cisystem@netdef.org>
(cherry picked from commit 693da6096a28eef5eadeea699771265987b3ec0c)
HAVE_OPAQUE_LSA is used by default and you have to actively turn it off
except that OPAQUE_LSA is an industry standard and used pretty much
everywhere. There is no need to have special #defines for this anymore.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit 36fef5708d074a3ef41f34d324c309c45bae119b)
OpenBSD doesn't support the "ifindex hack" derived from RFC 1724 which
allows an ifindex to be encoded in the imr_interface field (in_addr)
of the ip_mreq structure. OpenBSD also doesn't support the RFC3678
Protocol-Independent socket API extensions, which allows an interface
to be specified by its ifindex. With that said, in OpenBSD we still need
to specify an interface by its IP address. This patch adds an exception
in the multicast sockopt functions to handle this case.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
