Fixed as per rfc7761 section 4.3.1.
"""
Sending Hello Messages
The Address List option advertises all the secondary addresses
associated with the source interface of the router originating the
message. The option MUST be included in all Hello messages if there
are secondary addresses associated with the source interface and MAY
be omitted if no secondary addresses exist.
"""
Issue: #12015
Signed-off-by: Sarita Patra <saritap@vmware.com>
Proof:
eva# conf
eva(config)# no service integrated-vtysh-config
eva(config)# end
eva# wr mem
Note: this version of vtysh never writes vtysh.conf
Building Configuration...
Configuration saved to /etc/frr/zebra.conf
Configuration saved to /etc/frr/ripd.conf
Configuration saved to /etc/frr/ripngd.conf
Configuration saved to /etc/frr/ospfd.conf
Configuration saved to /etc/frr/ospf6d.conf
Configuration saved to /etc/frr/bgpd.conf
Configuration saved to /etc/frr/isisd.conf
Configuration saved to /etc/frr/pimd.conf
Configuration saved to /etc/frr/nhrpd.conf
Configuration saved to /etc/frr/eigrpd.conf
Configuration saved to /etc/frr/babeld.conf
Configuration saved to /etc/frr/sharpd.conf
Configuration saved to /etc/frr/fabricd.conf
Configuration saved to /etc/frr/pbrd.conf
Configuration saved to /etc/frr/staticd.conf
Configuration saved to /etc/frr/bfdd.conf
Configuration saved to /etc/frr/vrrpd.conf
Configuration saved to /etc/frr/pim6d.conf
eva#
Fixes: #12011
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When more than 2 routers are present in LAN and the querier
goes down, the other routers will wait for other querier
present timer to expire to elect a new querier.
This issue will be seen when the router having next lower ip
address expires the other querier present timer first and it
starts sending the query message. Now on the other non-querier
routers it will receive this query and reset its other
querier present timer but the querier is still the old one
and since it is lowest ip, it never gets updated to the newly
elected querier.
Reset the other querier timer only if query is received from
the previously elected querier or a better new querier
This will make sure that non-querier elects the new querier
whose ip address is higher than the old querier
when the old querier goes down via other querier querier
timer expiry
Issue: #12027
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
Implementing mld packets debug to information about packet generation for sending
and about packet handling from a received packet.
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Changing
IGMP_DEFAULT_ROBUSTNESS_VARIABLE to GM_DEFAULT_ROBUSTNESS_VARIABLE,
IGMP_GENERAL_QUERY_INTERVAL to GM_GENERAL_QUERY_INTERVAL,
IGMP_QUERY_MAX_RESPONSE_TIME_DSEC to GM_QUERY_MAX_RESPONSE_TIME_DSEC and
IGMP_SPECIFIC_QUERY_MAX_RESPONSE_TIME_DSEC to GM_SPECIFIC_QUERY_MAX_RESPONSE_TIME_DSEC
to accomodate both igmp and mld. And moved it to common file.
Signed-off-by: Abhishek N R <abnr@vmware.com>
After restart pim dr address was zero due to which pim (*,G) join
could not get propagated towards RP.
While trying to find primary address ll_highest will be zero initially,
since we have not received address from zebra yet.
So we can get the best address at this point and use it as primary address
whenever ll_highest is zero.
Fixes: #11925
Signed-off-by: Abhishek N R <abnr@vmware.com>
Root Cause:
"clear ipv6 mroute" was not deleting the subscribers of gm_if
structure.
Fix:
The command "clear ipv6 mroute" deletes grp_pends, gsq_pends, sgs,
subscribers, expires of gm_if data structure.
Deleted the common code in gm_ifp_teardown() and called
gm_group_delete().
Issue: #11724
Signed-off-by: Sarita Patra <saritap@vmware.com>
Changed PIM_DEBUG_IGMP_TRACE to PIM_DEBUG_GM_TRACE and
PIM_DEBUG_IGMP_TRACE_DETAIL to PIM_DEBUG_GM_TRACE_DETAIL.
Hence, these macros can be used for both v6 and v4.
Issue: #11895
Co-authored-by: Sai Gomathi N <nsaigomathi@vmware.com>
Signed-off-by: Abhishek N R <abnr@vmware.com>
Changing
PIM_DO_DEBUG_IGMP_EVENTS to PIM_DO_DEBUG_GM_EVENTS
PIM_DO_DEBUG_IGMP_PACKETS to PIM_DO_DEBUG_GM_PACKETS
PIM_DO_DEBUG_IGMP_TRACE to PIM_DO_DEBUG_GM_TRACE
PIM_DO_DEBUG_IGMP_TRACE_DETAIL to PIM_DO_DEBUG_GM_TRACE_DETAIL
PIM_DONT_DEBUG_IGMP_EVENTS to PIM_DONT_DEBUG_GM_EVENTS
PIM_DONT_DEBUG_IGMP_PACKETS to PIM_DONT_DEBUG_GM_PACKETS
PIM_DONT_DEBUG_IGMP_TRACE to PIM_DONT_DEBUG_GM_TRACE
PIM_DONT_DEBUG_IGMP_TRACE_DETAIL to PIM_DONT_DEBUG_GM_TRACE_DETAIL
PIM_MASK_IGMP_EVENTS to PIM_MASK_GM_EVENTS
PIM_MASK_IGMP_PACKETS to PIM_MASK_GM_PACKETS
PIM_MASK_IGMP_TRACE to PIM_MASK_GM_TRACE
PIM_MASK_IGMP_TRACE_DETAIL to PIM_MASK_GM_TRACE_DETAIL
to be used for both IGMP and MLD debugs.
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Added Robustness value, Query interval, Query response timer
and Last member query interval field in json output.
Issue: #11891
Signed-off-by: Abhishek N R <abnr@vmware.com>
Changing the macros to common so that it can be used for pimv6 debugs as well
to be used for both IGMP and MLD debugs.
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
Changing the macros to common so that it can be used for pimv6 debugs as well
to be used for both IGMP and MLD debugs.
Signed-off-by: Sai Gomathi N <nsaigomathi@vmware.com>
When there is update in the configuration of last_member_query_interval
and last_member_query_count, call gm_ifp_update().
This will update cur_query_intv_trig and cur_lmqc of gm_ifp structure.
Issue: #11901
Signed-off-by: Sarita Patra <saritap@vmware.com>
show ip pim state should show IGMP Report while
show ipv6 pim state should show MLD Report.
Output After Fix:
frr# do sh ip pim state
Codes: J -> Pim Join, I -> IGMP Report, S -> Source, * -> Inherited from (*,G), V -> VxLAN, M -> Muted
Active Source Group RPT IIF OIL
frr# do sh ipv6 pim state
Codes: J -> Pim Join, I -> MLD Report, S -> Source, * -> Inherited from (*,G), V -> VxLAN, M -> Muted
Active Source Group RPT IIF OIL
frr#
Issue: #11249
Signed-off-by: Mobashshera Rasool <mrasool@vmware.com>
