Adds a knob that sets the time between loc-rib scans for conditional
advertisement.
I chose the range (5-240) because 1 second seems dumb and too easy to
hurt yourself at even moderate scale, 5 seconds you can still hurt
yourself but I could see a use case for it, and 4 minutes should be
enough for anyone (tm)
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
the realloc man page:
If ptr is NULL, then the call is equivalent to malloc(size)
This should be sufficient for our needs to not have to have
XMALLOC and XREALLOC
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
There is no peer_af allocated in `peer_activate`. Trying to delete
the structure just results in an no-op and a error return value.
The error message "couldn't delete af structure for peer" is
unexpected.
Signed-off-by: zyxwvu Shi <shiyuchen.syc@bytedance.com>
New peers should be initialized with a usual max packet size and later
determined on OPEN messages.
Testing with different peers supporting/not supporting extended support.
2021/07/02 13:48:00 BGP: [WEV7K-2GAQ5] u2:s2 send UPDATE len 8991 (max message len: 65535) numpfx 1788
2021/07/02 13:48:03 BGP: [WEV7K-2GAQ5] u3:s3 send UPDATE len 4096 (max message len: 4096) numpfx 809
2021/07/02 13:48:03 BGP: [WEV7K-2GAQ5] u3:s3 send UPDATE len 4096 (max message len: 4096) numpfx 809
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
There are a few places in the code where we use PREFIX_COPY(_IPV4/IPV6)
macro to copy a prefix. Let's always use prefix_copy function for this.
This should fix CID 1482142 and 1504610.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Adds new commands to allow a user to default 'default' address-families
to be inherited by all new peers. Previously this was limited to just
ipv4/ipv6 unicast, now the full list is:
---
ipv4-unicast
ipv4-multicast
ipv4-vpn
ipv4-labeled-unicast
ipv4-flowspec
ipv6-unicast
ipv6-multicast
ipv6-vpn
ipv6-labeled-unicast
ipv6-flowspec
l2vpn-evpn
---
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Introduces bgp->default_af to selectively enable various default
afi/safis to be inherited by new peers.
Makes default_af flag logic consistent for all address-families, i.e.
instead of a "no default" flag for ipv4 and a "default" flag for ipv6,
just use "default" for both and make it true for ipv4 by default.
Removes old BGP_FLAG_NO_DEFAULT_IPV4 and BGP_FLAG_DEFAULT_IPV6, and
cleans up bgp->flags bit definitions to avoid gaps for unused bits.
Signed-off-by: Trey Aspelund <taspelund@nvidia.com>
Display on which VRF/view the neighbor was not found. Useful when
selecting "vrf all".
Before patch:
No such neighbor in this view/vrf
After patch:
No such neighbor in VRF default
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
We are inconsistently using peer_establiahed(peer) with
sometimes using `peer->status == Established`. Just Convert
over to using the function for consistency.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
BGP configuration changes that imply recomputing the BGP route table
(e.g. modifying route-maps, setting bgp graceful-shutdown) might be a
long time process depending on the size of the BGP table and the
route-map numbers and complexity. For example, setups with full
Internet routes take something like one minute to reprocess all the
prefixes when graceful-shutdown is configured. During this time, a
"show bgp commands" request on vtysh results in blocking the shell until
the soft reconfigure table task is over.
This patch splits bgp_soft_reconfig_table task into thread jobs of 25K
prefixes.
Some tests on a full Internet route setup show that after reconfiguring
route-maps or graceful-shutdown, vtysh is not stucked anymore. We are
now able to request commands like "show bgp summary" after 1 or 2
seconds instead of 30 to 60s.
Signed-off-by: Louis Scalbert <louis.scalbert@6wind.com>
This commit add base-lines for BGP SRv6 VPN support.
srv6_locator_chunks property of struct bgp is used
to store BGPd's own SRv6 locator chunk getting with
ZEBRA_SRV6_MANAGER_GET_LOCATOR_CHUNK api.
And srv6_functions is used to store BGP's srv6
localsids. It's mainly used when new SID reservation
from locator chunks.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
base
Currently, when AS number of an existing BGP neighbor is added in a BGP
confederation, AS_CONFED_SEQUENCE segment attribute will be missing in
prefixes advertised to the neighbor. Also, receiving prefixes from the
neighbor will be withdrawn because of "Malformed AS path from A.B.C.D".
neighbor 10.100.200.3 remote-as 123
bgp confederation identifier 65001
bgp confederation peers 123
With this change, update peer's sort after adding or removing its AS
number in a BGP confederation.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
Deconfiguring conditional advertisement resulted in all other policy
settings on the peer getting removed due to an excessively large memset.
This also created a desync with the northbound config tree, which caused
its own set of problems...
Fix the memset to just remove the conditional advertisement config.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
BGP_MAX_PACKET_SIZE no longer represented the absolute maximum BGP
packet size as it did before, instead it was defined as 4096 bytes,
which is the maximum unless extended message capability is negotiated,
in which case the maximum goes to 65k.
That introduced at least one bug - last_reset_cause was undersized for
extended messages, and when sending an extended message > 4096 bytes
back to a peer as part of NOTIFY data would trigger a bounds check
assert.
This patch redefines the macro to restore its previous meaning,
introduces a new macro - BGP_STANDARD_MESSAGE_MAX_PACKET_SIZE - to
represent the 4096 byte size, and renames the extended size to
BGP_EXTENDED_MESSAGE_MAX_PACKET_SIZE for consistency. Code locations
that definitely should use the small size have been updated, locations
that semantically always need whatever the max is, no matter what that
is, use BGP_MAX_PACKET_SIZE.
BGP_EXTENDED_MESSAGE_MAX_PACKET_SIZE should only be used as a constant
when storing what the negotiated max size is for use at runtime and to
define BGP_MAX_PACKET_SIZE. Unless there is a future standard that
introduces a third valid size it should not be used for any other
purpose.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Show alias name instead of numerical value in `show bgp <prefix>. E.g.:
```
root@exit1-debian-9:~/frr# vtysh -c 'sh run' | grep 'bgp community alias'
bgp community alias 65001:123 community-1
bgp community alias 65001:123:1 lcommunity-1
root@exit1-debian-9:~/frr#
```
```
exit1-debian-9# sh ip bgp 172.16.16.1/32
BGP routing table entry for 172.16.16.1/32, version 21
Paths: (2 available, best #2, table default)
Advertised to non peer-group peers:
65030
192.168.0.2 from home-spine1.donatas.net(192.168.0.2) (172.16.16.1)
Origin incomplete, metric 0, valid, external, best (Neighbor IP)
Community: 65001:12 65001:13 community-1 65001:65534
Large Community: lcommunity-1 65001:123:2
Last update: Fri Apr 16 12:51:27 2021
exit1-debian-9#
```
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Problem Statement:
=================
In scale setup BGP sessions start flapping.
RCA:
====
In virtualized environment there are multiple places where
MTU need to be set. If there are some places were MTU is not set
properly then there is chances that BGP packets get fragmented,
in scale setup this will lead to BGP session flap.
Fix:
====
A new tcp option is provided as part of this implementation,
which can be configured per neighbor and helps to set the TCP
max segment size. User need to derive the path MTU between the BGP
neighbors and set that value as part of tcp-mss setting.
1. CLI Configuration:
[no] neighbor <A.B.C.D|X:X::X:X|WORD> tcp-mss (1-65535)
2. Running config
frr# show running-config
router bgp 100
neighbor 198.51.100.2 tcp-mss 150 => new entry
neighbor 2001:DB8::2 tcp-mss 400 => new entry
3. Show command
frr# show bgp neighbors 198.51.100.2
BGP neighbor is 198.51.100.2, remote AS 100, local AS 100, internal link
Hostname: frr
Configured tcp-mss is 150, synced tcp-mss is 138 => new display
4. Show command json output
frr# show bgp neighbors 2001:DB8::2 json
{
"2001:DB8::2":{
"remoteAs":100,
"bgpTimerKeepAliveIntervalMsecs":60000,
"bgpTcpMssConfigured":400, => new entry
"bgpTcpMssSynced":388, => new entry
Risk:
=====
Low - This is a config driven feature and it sets the max segment
size for the TCP session between BGP peers.
Tests Executed:
===============
Have done manual testing with three router topology.
1. Executed basic config and un config scenarios
2. Verified if the config is updated in running config
during config and no config operation
3. Verified the show command output in both CLI format and
JSON format.
4. Verified if TCP SYN messages carry the max segment size
in their initial packets.
5. Verified the behaviour during clear bgp session.
6. done packet capture to see if the new segment size
takes effect.
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
When we're trying to create the config for already existing router and
the AS number or instance type mismatches, we're returning the
inconsistency error and don't set the NB entry.
Any subsequent command that configures this router will crash because
every command relies on the existence of the NB entry.
Let's store the entry even when there's a mismatch to prevent the crash.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
There are multiple problems:
- commit ef7c53e2 introduced a new return value 2 which broke things,
because a lot of code treats non-zero return as an error,
- there is an incorrect error returned when AS number mismatches.
This commit fixes both.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
Description:
FRR doesn't re-install the routes, imported from a tenant VRF,
when bgp instance for source vrf is deleted and re-added again.
When bgp instance is removed and re-added, when import statement is already there,
then route leaking stops between two VRFs.
Every 'router bgp' command should trigger re-export of all the routes
to the importing bgp vrf instances.
When a router bgp is configured, there could be bgp vrf instance(s) importing routes from
this newly configured bgp vrf instance.
We need to export routes from configured bgp vrf to VPN.
This can impact performance, whenever we are testing scale from vrf route-leaking perspective.
We should not trigger re-export for already existing bgp vrf instances.
Co-authored-by: Santosh P K <sapk@vmware.com>
Co-authored-by: Kantesh Mundaragi <kmundaragi@vmware.com>
Signed-off-by: Abhinay Ramesh <rabhinay@vmware.com>
Remove old BFD API usage and replace it with the new one.
Highlights:
- More shared code: the daemon gets notified with callbacks instead of
having to roll its own code to find the notified sessions.
- Less code to integrate with BFD.
- Remove hidden commands to configure single / multi hop. Use
protocol data instead.
BGP can determine if a peer is single/multi hop according to the
following criteria:
a. If the IP address is a link-local address (single hop)
b. The network is shared with peer (single hop)
c. BGP is configured for eBGP multi hop / TTL security (multi hop)
- Respect the configuration hierarchy:
a. Peer configuration take precendence over peer-group
configuration.
b. When peer group configuration is removed, reset peer
BFD configurations to defaults (unless peer had specific
configs).
Example:
neighbor foo peer-group
neighbor foo bfd profile X
neighbor 192.168.0.2 peer-group foo
neighbor 192.168.0.2 bfd
! If peer-group is removed the profile configuration gets
! removed from peer 192.168.0.2, but BFD will still enabled
! because of the neighbor specific bfd configuration.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
If we have a SAFI conflict, ie we are trying to activate safi's
UNICAST and LABELED_UNICAST at the same time, we should not
cause bestpath to be rerun and we should not try to put
labels on everything.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When you use a single BGP session for both IPv4 and IPv6 it's a bit
annoying going into ipv6 address-family and explicitly activating it.
Let's get this automatically if enabled with `bgp default ipv6-unicast`.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Description:
When user is config connect timer, it doesn't reflect
immediately. It reflect when next time neighbor is tried to reconnect.
Problem Description/Summary :
When user is config connect timer, it doesn't reflect
The network connection was aborted by the local system.d to reconnect.
Fix is to update the connect timer immediately if BGP
session is not in establish state.
Expected Behavior :
If neighbor is not yet established, we should immediately apply the config connect timer to the peer.
Signed-off-by: sudhanshukumar22 <sudhanshu.kumar@broadcom.com>
Add SNMP support for L3vpn Vrf table as defined in [RFC4382]
Keep track of vrf status for the table and for future traps.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
Unconfig not resetting the peer-group member allowas_in[afi][safi]
This is causing remote route to be accept.
Signed-off-by: Kishore Kunal <kishorekunal01@broadcom.com>
Description:
Holdtime and keepalive parameters weren't copied from
peer-group to peer-group members. Fixed the issue by copying holdtime
and keepalive parameters from peer-group to its members.
Problem Description/Summary :
Holdtime and keepalive parameters weren't copied from
peer-group to peer-group members. Fixed the issue by copying holdtime
and keepalive parameters from peer-group to its members.
Signed-off-by: sudhanshukumar22 <sudhanshu.kumar@broadcom.com>
The command `neighbor PGROUP ttl-security hops X` was being
accepted but ignored. Allow it to be stored. I am still
not sure that this is applied correctly, but that is another
problem.
Fixes: #7848
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
A bgp neighbor remains in Idle state in the event that the number
of received prefixes exceeds the configured maximum prefix for the
neighbor. The neighbor remains in idle state even after de-configuring
the maximum prefix limit for the neighbor.
The fix is to clear the neighbor overflow state if set, after
de-configuring the neighbor maximum-prefix commnd.
This allows the neighbor to establish without having to perform a
clear operation. It also avoids the misleading neigbor summary
indicating that the neighbor is in prefix overflow state (PfxCt)
when no limit is configured for the neighbor.
Signed-off-by: Dewi Morgan <dewi.morgan@intl.att.com>
When adding/removing some peer's flag we need to make sure we FORCE updates
to avoid suppressing critical updates.
Like entering `no neighbor x.x.x.x send-community large` would suppress
updates by default and another side will have stale large communities.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Fix `peer_default_originate_unset` so default route can be withdrawn
when `default-originate` option is being unset from a peer-group.
The loop calling `bgp_default_originate` is clearing default-originate
from the peer-group peer `peer` instead of the peer-group member peer
`member`.
Signed-off-by: zyxwvu Shi <shiyuchen.syc@bytedance.com>
On top of the recent `bgp suppress-fib-pending which
was at a BGP_NODE level, add this command at the CONFIG_NODE
level as well and allow the command to apply to all instances
of bgp running.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add a bit of code to allow bgp to send the AS-Path associated with
the route being installed to zebra so it can be displayed and
used as part of the `show ip route A` command in zebra.
eva# show ip route 20.0.0.0/11
Routing entry for 20.0.0.0/11
Known via "bgp", distance 20, metric 0, best
Last update 00:00:00 ago
* 192.168.161.1, via enp39s0, weight 1
AS-Path: 60000 64539 15096 6939 8075
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Changes implement dampening profiles for peers and peer groups. This is
achieved by introducing the possibility to have multible existing
dampening configurations with their own sets of parameters and lists of
associated paths.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
ES-VRF entries are maintained for the purpose of L3-NHG creation -
1. Each ES-EVI entry is associated with a tenant VRF. This associaton
triggers the creation of an ES-VRF entry.
2. Type-2/MAC-IP routes are imported into a tenant VRF and programmed as
a /32 or host route entry in the dataplane. If the destination of
the host route is a remote-ES the route is programmed with the
corresponding (keyed in by {vrf,ES-id}) L3-NHG.
3. The reason for this indirection (route->L3-NHG, L3-NHG->list-of-VTEPs)
is to avoid route updates to the dplane when a remote-ES link flaps i.e.
instead of updating all the dependent routes the NHG's contents are
updated. This reduces the amount of dataplane updates (fewer nhg updates vs.
route updates) allowing for a faster failover.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
The return from sockunion2hostprefix tells us if the conversion
succeeded or not. There are places in the code where we
always assume that it just `works`, since it can fail
notice and try to do the right thing.
Please note that failure of this function for most cases
of sockunion2hostprefix is highly highly unlikely as that
the sockunion was already created and tested elsewhere
it's just that this function can fail.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When a BGP vrf instance is deleted, the routes it exported into the
main VPN table are not deleted and they remain as stale routes
attached to an unknown bgp instance. When the new vrf instance comes
along, it imports these routes from the main table and thus we see
duplicatesalongside its own identical routes.
The solution is to call the unexport logic when a BGP vrf instance is
being deleted.
problem example
---------------
volta1# sh bgp vrf VRF-a ipv4 unicast
BGP table version is 4, local router ID is 18.0.0.1, vrf id 5
Default local pref 100, local AS 567
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 7.0.0.6/32 7.0.0.5@0< 10 100 0 ?
*> 7.0.0.8/32 18.0.0.8 0 0 111 ?
*> 18.0.0.0/24 18.0.0.8 0 0 111 ?
*> 56.0.0.0/24 7.0.0.5@0< 0 100 0 ?
Displayed 4 routes and 4 total paths
volta1# conf t
volta1(config)# no router bgp 567 vrf VRF-a
volta1(config)#
volta1(config)# router bgp 567 vrf VRF-a
volta1(config-router)# bgp router-id 18.0.0.1
volta1(config-router)# no bgp ebgp-requires-policy
volta1(config-router)# no bgp network import-check
volta1(config-router)# neighbor 18.0.0.8 remote-as 111
volta1(config-router)# !
volta1(config-router)# address-family ipv4 unicast
volta1(config-router-af)# label vpn export 12345
volta1(config-router-af)# rd vpn export 567:111
volta1(config-router-af)# rt vpn both 567:100
volta1(config-router-af)# export vpn
volta1(config-router-af)# import vpn
volta1(config-router-af)# exit-address-family
volta1(config-router)# !
volta1(config-router)# end
volta1# sh bgp vrf VRF-a ipv4 unicast
BGP table version is 4, local router ID is 18.0.0.1, vrf id 5
Default local pref 100, local AS 567
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 7.0.0.6/32 7.0.0.5@0< 10 100 0 ?
* 7.0.0.8/32 18.0.0.8 0 0 111 ?
*> 18.0.0.8@-< 0 0 111 ?
* 18.0.0.0/24 18.0.0.8 0 0 111 ?
*> 18.0.0.8@-< 0 0 111 ?
*> 56.0.0.0/24 7.0.0.5@0< 0 100 0 ?
Displayed 4 routes and 6 total paths
@- routes indicating unknown bgp instance are imported
Signed-off-by: Pat Ruddy <pat@voltanet.io>
if the user sets the ebgp-multihop for a neighbor to the same value
we currently have, avoid resetting the session and just return a
silent success.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
* Added CLI command "[no] bgp suppress-fib-pending" to enable and
disable suppress-fib-pending
* Send ZEBRA_ROUTE_NOTIFY_REQUEST to zebra when "bgp suppress-fib-pending"
is enabled or disabled
* Define BGP_DEFAULT_UPDATE_ADVERTISEMENT_TIME which is the delay added
to update group timer.
* Added error codes
Signed-off-by: kssoman <somanks@gmail.com>
We are allocating temporary memory for information about
what to process in this thread, which is not being cleaned
up on thread cancelling.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The `struct listnode *rt_node` data structure is adding
8 bytes of size to the `struct bgp_dest`. This is a large
amount of data for a flag we are already setting on each
node for this. Just set the flag and use that to figure
out who we are doing graceful restart on.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Sample Configuration with prefix-list and community match rules
---------------------------------------------------------------
R1 ------- R2(DUT) ------- R3
Router2# show running-config
Building configuration...
Current configuration:
!
frr version 7.6-dev-MyOwnFRRVersion
frr defaults traditional
hostname router
log file /var/log/frr/bgpd.log
log syslog informational
hostname Router2
service integrated-vtysh-config
!
debug bgp updates in
debug bgp updates out
!
debug route-map
!
ip route 20.20.0.0/16 blackhole
ipv6 route 2001:db8::200/128 blackhole
!
interface enp0s9
ip address 10.10.10.2/24
!
interface enp0s10
ip address 10.10.20.2/24
!
interface lo
ip address 2.2.2.2/32
!
router bgp 2
bgp log-neighbor-changes
no bgp ebgp-requires-policy
neighbor 10.10.10.1 remote-as 1
neighbor 10.10.20.3 remote-as 3
!
address-family ipv4 unicast
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.20.3 soft-reconfiguration inbound
neighbor 10.10.20.3 advertise-map ADV-MAP non-exist-map EXIST-MAP
exit-address-family
!
ip prefix-list DEFAULT seq 5 permit 1.1.1.5/32
ip prefix-list DEFAULT seq 10 permit 1.1.1.1/32
ip prefix-list EXIST seq 5 permit 10.10.10.10/32
ip prefix-list DEFAULT-ROUTE seq 5 permit 0.0.0.0/0
ip prefix-list IP1 seq 5 permit 10.139.224.0/20
ip prefix-list T2 seq 5 permit 1.1.1.5/32
!
bgp community-list standard DC-ROUTES seq 5 permit 64952:3008
bgp community-list standard DC-ROUTES seq 10 permit 64671:501
bgp community-list standard DC-ROUTES seq 15 permit 64950:3009
bgp community-list standard DEFAULT-ROUTE seq 5 permit 65013:200
!
route-map ADV-MAP permit 10
match ip address prefix-list IP1
!
route-map ADV-MAP permit 20
match community DC-ROUTES
!
route-map EXIST-MAP permit 10
match community DEFAULT-ROUTE
match ip address prefix-list DEFAULT-ROUTE
!
line vty
!
end
Router2#
Router2# show ip bgp 0.0.0.0
BGP routing table entry for 0.0.0.0/0
Paths: (1 available, best #1, table default)
Advertised to non peer-group peers:
10.10.10.1 10.10.20.3
1
10.10.10.1 from 10.10.10.1 (10.139.224.1)
Origin IGP, metric 0, valid, external, best (First path received)
Community: 64848:3011 65011:200 65013:200
Last update: Tue Oct 6 02:39:42 2020
Router2#
Sample output with non-exist-map when default route present in table
--------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 4, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 10.10.10.1 0 0 1 i
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 4 routes and 4 total paths
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 4, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 0.0.0.0 0 1 i
*> 1.1.1.5/32 0.0.0.0 0 1 i <<<<<<<<< non-exist-map : 0.0.0.0/0 is present so, 10.139.224.0/20 not advertised
Total number of prefixes 2
Sample output with non-exist-map when default route not present in table
------------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 3 routes and 3 total paths
Router2#
Router2#
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 5, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 0.0.0.0 0 1 i
*> 1.1.1.5/32 0.0.0.0 0 1 i
*> 10.139.224.0/20 0.0.0.0 0 1 ? <<<<<<<<< non-exist-map : 0.0.0.0/0 is not present so, 10.139.224.0/20 advertised
Total number of prefixes 3
Router2#
Sample output with exist-map when default route present in table
--------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 10.10.10.1 0 0 1 i
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 4 routes and 4 total paths
Router2#
Router2#
Router2#
Router2#
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 0.0.0.0/0 0.0.0.0 0 1 i
*> 1.1.1.1/32 0.0.0.0 0 1 i
*> 1.1.1.5/32 0.0.0.0 0 1 i
*> 10.139.224.0/20 0.0.0.0 0 1 ? <<<<<<<<< exist-map : 0.0.0.0/0 is present so, 10.139.224.0/20 advertised
Total number of prefixes 4
Router2#
Sample output with exist-map when default route not present in table
--------------------------------------------------------------------
Router2# show ip bgp
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.1/32 10.10.10.1 0 0 1 i
*> 1.1.1.5/32 10.10.10.1 0 0 1 i
*> 10.139.224.0/20 10.10.10.1 0 0 1 ?
Displayed 3 routes and 3 total paths
Router2#
Router2#
Router2#
Router2# show ip bgp neighbors 10.10.20.3 advertised-routes
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.5/32 0.0.0.0 0 1 i <<<<<<<<< exist-map : 0.0.0.0/0 is not present so, 10.139.224.0/20 not advertised
Total number of prefixes 1
Router2#
Signed-off-by: Madhuri Kuruganti <k.madhuri@samsung.com>
Implemented as per the feature description given in the source link.
Descriprion:
The BGP conditional advertisement feature uses the non-exist-map or exist-map
and the advertise-map keywords of the neighbor advertise-map command in order
to track routes by the route prefix.
non-exist-map :
If a route prefix is not present in output of the non-exist-map command, then
the route specified by the advertise-map command is announced.
exist-map :
If a route prefix is present in output of the exist-map command, then the route
specified by the advertise-map command is announced.
The conditional BGP announcements are sent in addition to the normal
announcements that a BGP router sends to its peers.
The conditional advertisement process is triggered by the BGP scanner process,
which runs every 60 seconds. This means that the maximum time for the conditional
advertisement to take effect is 60 seconds. The conditional advertisement can take
effect sooner, depending on when the tracked route is removed from the BGP table
and when the next instance of the BGP scanner occurs.
Sample Configuration on DUT
---------------------------
Router2# show running-config
Building configuration...
Current configuration:
!
frr version 7.6-dev-MyOwnFRRVersion
frr defaults traditional
hostname router
log file /var/log/frr/bgpd.log
log syslog informational
hostname Router2
service integrated-vtysh-config
!
debug bgp updates in
debug bgp updates out
!
debug route-map
!
ip route 200.200.0.0/16 blackhole
ipv6 route 2001:db8::200/128 blackhole
!
interface enp0s9
ip address 10.10.10.2/24
!
interface enp0s10
ip address 10.10.20.2/24
!
interface lo
ip address 2.2.2.2/24
ipv6 address 2001:db8::2/128
!
router bgp 2
bgp log-neighbor-changes
no bgp ebgp-requires-policy
neighbor 10.10.10.1 remote-as 1
neighbor 10.10.20.3 remote-as 3
!
address-family ipv4 unicast
network 2.2.2.0/24
network 200.200.0.0/16
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE non-exist-map CONDITION
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
address-family ipv6 unicast
network 2001:db8::2/128
network 2001:db8::200/128
neighbor 10.10.10.1 activate
neighbor 10.10.10.1 soft-reconfiguration inbound
neighbor 10.10.10.1 advertise-map ADVERTISE_6 non-exist-map CONDITION_6
neighbor 10.10.20.3 activate
neighbor 10.10.20.3 soft-reconfiguration inbound
exit-address-family
!
access-list CONDITION seq 5 permit 3.3.3.0/24
access-list ADVERTISE seq 5 permit 2.2.2.0/24
access-list ADVERTISE seq 6 permit 200.200.0.0/16
access-list ADVERTISE seq 7 permit 20.20.0.0/16
!
ipv6 access-list ADVERTISE_6 seq 5 permit 2001:db8::2/128
ipv6 access-list CONDITION_6 seq 5 permit 2001:db8::3/128
!
route-map ADVERTISE permit 10
match ip address ADVERTISE
!
route-map CONDITION permit 10
match ip address CONDITION
!
route-map ADVERTISE_6 permit 10
match ipv6 address ADVERTISE_6
!
route-map CONDITION_6 permit 10
match ipv6 address CONDITION_6
!
line vty
!
end
Router2#
Withdraw when non-exist-map prefixes present in BGP table:
----------------------------------------------------------
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 3.3.3.0/24 10.10.20.3 0 0 3 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 4 routes and 4 total paths
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::3/128 fe80::a00:27ff:fe76:6738 0 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 4 routes and 4 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
BGP neighbor is 10.10.10.1, remote AS 1, local AS 2, external link
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Withdraw
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Withdraw
1 accepted prefixes
!--- Output suppressed.
Router2#
Here 2.2.2.0/24 & 200.200.0.0/16 (prefixes in advertise-map) are withdrawn
by conditional advertisement scanner as the prefix(3.3.3.0/24) specified
by non-exist-map is present in BGP table.
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 3.3.3.0/24 0.0.0.0 0 3 i
Total number of prefixes 2
For address family: IPv6 Unicast
BGP table version is 8, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::3/128 :: 0 3 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Advertise when non-exist-map prefixes not present in BGP table:
---------------------------------------------------------------
After Removing 3.3.3.0/24 (prefix present in non-exist-map),
2.2.2.0/24 & 200.200.0.0/16 (prefixes present in advertise-map) are advertised
Router2# show ip bgp all wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 10.10.10.1 0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Displayed 3 routes and 3 total paths
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 fe80::a00:27ff:fecb:ad57 0 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Displayed 3 routes and 3 total paths
Router2#
Router2# show ip bgp neighbors 10.10.10.1
!--- Output suppressed.
For address family: IPv4 Unicast
Update group 9, subgroup 5
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION, Advertise-map *ADVERTISE, status: Advertise
1 accepted prefixes
For address family: IPv6 Unicast
Update group 10, subgroup 6
Packet Queue length 0
Inbound soft reconfiguration allowed
Community attribute sent to this neighbor(all)
Condition NON_EXIST, Condition-map *CONDITION_6, Advertise-map *ADVERTISE_6, status: Advertise
1 accepted prefixes
!--- Output suppressed.
Router2#
Router2# show ip bgp all neighbors 10.10.10.1 advertised-routes wide
For address family: IPv4 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 1.1.1.0/24 0.0.0.0 0 1 i
*> 2.2.2.0/24 0.0.0.0 0 32768 i
*> 200.200.0.0/16 0.0.0.0 0 32768 i
Total number of prefixes 3
For address family: IPv6 Unicast
BGP table version is 9, local router ID is 2.2.2.2, vrf id 0
Default local pref 100, local AS 2
Status codes: s suppressed, d damped, h history, * valid, > best, = multipath,
i internal, r RIB-failure, S Stale, R Removed
Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
Origin codes: i - IGP, e - EGP, ? - incomplete
Network Next Hop Metric LocPrf Weight Path
*> 2001:db8::1/128 :: 0 1 i
*> 2001:db8::2/128 :: 0 32768 i
*> 2001:db8::200/128 :: 0 32768 i
Total number of prefixes 3
Router2#
Signed-off-by: Madhuri Kuruganti <k.madhuri@samsung.com>
We currently have a global process queue for handling route
updates in bgp. This is fine, in general, except there are
places and times where we plug the queue for no new work
during certain peer states of bgp update delay. If we
happen to be processing multiple bgp instances on startup
why do we want to stop processing in vrf A when vrf B
is in a bit of a pickle?
Also this separation will allow us to start forward thinking
about how to fully integrate pthreads into route processing
in bgp.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The MH datastructures were being released before the paths that were
referencing them. Fix is to do the MH cleanup last.
The MH finish function has also been stripped down to only do a
datastructure cleanup i.e. avoid sending route updates etc.
Ticket: 31376
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Problem found that if a router-id was not defined or derived
initially, the bgp->router_id would be set to 0x0 and used
for determining auto-rd values. When bgp received a subsequent
router-id update from zebra, bgp would not completely process
the update since it was treated as updating an already derived
router-id with a new value, which is not desired. This also
could leave the auto rd/rt inforamation missing or invalid in
some cases. This fix allows updating the derived router-id if
the previous value was 0/0.
Ticket: CM-31441
Signed-off-by: Don Slice <dslice@nvidia.com>
Enhancement to update-delay configuration to allow setting globally
rather than per-instance. Setting the update-delay is allowed either
per-vrf or globally, but not both at the same time.
Ticket: CM-31096
Signed-off-by: Don Slice <dslice@nvidia.com>
* Added vtysh cli commands and functions to set/unset bgp daemons no-rib
option during runtime and withdraw/announce routes in bgp instances
RIB from/to Zebra.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
When deleting a dynamic peer, unsetting md5 password would cause
it to be unset on the listener allowing unauthenticated connections
from any peer in the range.
Check for dynamic peers in peer delete and avoid this.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
When setting authentication on a BGP peer in a VRF the listener is
looked up from a global list. However there is no check that the
listener is the one associated with the VRF being configured. This
can result in the wrong listener beiong configured with a password,
leaving the intended listener in an open authentication state.
To simplify this lookup stash a pointer to the bgp instance in
the listener on creating (in the same way as is done for NS-based
VRFS).
Signed-off-by: Pat Ruddy <pat@voltanet.io>
If you configure eBGP on loopbacks, you might miss setting the
ebgp-multihop option. Given that, the session will not be established
because of this. Now, the session is in Active state. When you update
your config afterwards and set the ebgp-multihop option to the
appropriate value, the session will still be in Active state. In fact,
it will be stuck in Active state and only services restart will help.
With this change, when set the ebgp-multihop option and no session was
established, reset the session.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
* Applied style suggestions by automated compliance check.
* Fixed function bgp_shutdown_enable to use immutable message string.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
* Peers are now automatically restarted by the reconnect timer instead
of a ManualStart event after lifting the administrative shutdown.
* Question of when to log what remains.
* Compiles and works as intended now.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
* Fixed integration in FSM and packet handling.
* Added CLI "show" output, incl. JSON.
* For review and testing only.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
* Changes allow administratively shutting down all peers of a BGP
instance.
* New CLI commands "[no] bgp shutdown" in vty shell.
* For review and testing only.
Signed-off-by: David Schweizer <dschweizer@opensourcerouting.org>
This is the base patch that brings in support for Type-1 routes.
It includes support for -
- Ethernet Segment (ES) management
- EAD route handling
- MAC-IP (Type-2) routes with a non-zero ESI i.e. Aliasing for
active-active multihoming
- Initial infra for consistency checking. Consistency checking
is a fundamental feature for active-active solutions like MLAG.
We will try to levarage the info in the EAD-ES/EAD-EVI routes to
detect inconsitencies in access config across VTEPs attached to
the same Ethernet Segment.
Functionality Overview -
========================
1. Ethernet segments are created in zebra and associated with
access VLANs. zebra sends that info as ES and ES-EVI objects to BGP.
2. BGP advertises EAD-ES and EAD-EVI routes for the locally attached
ethernet segments.
3. Similarly BGP processes EAD-ES and EAD-EVI routes from peers
and translates them into ES-VTEP objects which are then sent to zebra
as remote ESs.
4. Each ES in zebra is associated with a list of active VTEPs which
is then translated into a L2-NHG (nexthop group). This is the ES
"Alias" entry
5. MAC-IP routes with a non-zero ESI use the alias entry created in
(4.) to forward traffic i.e. a MAC-ECMP is done to these remote-ES
destinations.
EAD route management (route table and key) -
============================================
1. Local EAD-ES routes
a. route-table: per-ES route-table
key: {RD=ES-RD, ESI, ET=0xffffffff, VTEP-IP)
b. route-table: per-VNI route-table
Not added
c. route-table: global route-table
key: {RD=ES-RD, ESI, ET=0xffffffff)
2. Remote EAD-ES routes
a. route-table: per-ES route-table
Not added
b. route-table: per-VNI route-table
key: {RD=ES-RD, ESI, ET=0xffffffff, VTEP-IP)
c. route-table: global route-table
key: {RD=ES-RD, ESI, ET=0xffffffff)
3. Local EAD-EVI routes
a. route-table: per-ES route-table
Not added
b. route-table: per-VNI route-table
key: {RD=0, ESI, ET=0, VTEP-IP)
c. route-table: global route-table
key: {RD=L2-VNI-RD, ESI, ET=0)
4. Remote EAD-EVI routes
a. route-table: per-ES route-table
Not added
b. route-table: per-VNI route-table
key: {RD=0, ESI, ET=0, VTEP-IP)
c. route-table: global route-table
key: {RD=L2-VNI-RD, ESI, ET=0)
Please refer to bgp_evpn_mh.h for info on how the data-structures are
organized.
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Revert "zebra: support for macvlan interfaces"
This reverts commit bf69e212fd.
Revert "doc: add some documentation about bgp evpn netns support"
This reverts commit 89b97c33d7.
Revert "zebra: dynamically detect vxlan link interfaces in other netns"
This reverts commit de0ebb2540.
Revert "bgpd: sanity check when updating nexthop from bgp to zebra"
This reverts commit ee9633ed87.
Revert "lib, zebra: reuse and adapt ns_list walk functionality"
This reverts commit c4d466c830.
Revert "zebra: local mac entries populated in correct netnamespace"
This reverts commit 4042454891.
Revert "zebra: when parsing local entry against dad, retrieve config"
This reverts commit 3acc394bc5.
Revert "bgpd: evpn nexthop can be changed by default"
This reverts commit a2342a2412.
Revert "zebra: zvni_map_to_vlan() adaptation for all namespaces"
This reverts commit db81d18647.
Revert "zebra: add ns_id attribute to mac structure"
This reverts commit 388d5b438e.
Revert "zebra: bridge layer2 information records ns_id where bridge is"
This reverts commit b5b453a2d6.
Revert "zebra, lib: new API to get absolute netns val from relative netns val"
This reverts commit b6ebab34f6.
Revert "zebra, lib: store relative default ns id in each namespace"
This reverts commit 9d3555e06c.
Revert "zebra, lib: add an internal API to get relative default nsid in other ns"
This reverts commit 97c9e7533b.
Revert "zebra: map vxlan interface to bridge interface with correct ns id"
This reverts commit 7c990878f2.
Revert "zebra: fdb and neighbor table are read for all zns"
This reverts commit f8ed2c5420.
Revert "zebra: zvni_map_to_svi() adaptation for other network namespaces"
This reverts commit 2a9dccb647.
Revert "zebra: display interface slave type"
This reverts commit fc3141393a.
Revert "zebra: zvni_from_svi() adaptation for other network namespaces"
This reverts commit 6fe516bd4b.
Revert "zebra: importation of bgp evpn rt5 from vni with other netns"
This reverts commit 28254125d0.
Revert "lib, zebra: update interface name at netlink creation"
This reverts commit 1f7a68a2ff.
Signed-off-by: Pat Ruddy <pat@voltanet.io>
If _force_ is set, then ALL prefixes are counted for maximum instead of
accepted only. This is useful for cases where an inbound filter is applied,
but you want maximum-prefix to act on ALL (including filtered) prefixes.
For instance, we have a configuration like:
neighbor r1 maximum-prefix 10
neighbor r1 prefix-list custom in
!
ip prefix-list custom seq 1 permit 10.0.0.0/24
ip prefix-list custom seq 2 permit 10.0.1.0/24
This will accept only 2 prefixes and discard all others instead of
shutting down the session when 10 is reached.
With this new knob (force), we will count all received prefixes and shutdown
the session when 10 is reached.
The bigger problem is when you have lots of peers with full feed and such a
configuration like in an example.
This is kinda re-ordering of how to treat filter vs. maximum-prefix.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Remove mid-string line breaks, cf. workflow doc:
.. [#tool_style_conflicts] For example, lines over 80 characters are allowed
for text strings to make it possible to search the code for them: please
see `Linux kernel style (breaking long lines and strings)
<https://www.kernel.org/doc/html/v4.10/process/coding-style.html#breaking-long-lines-and-strings>`_
and `Issue #1794 <https://github.com/FRRouting/frr/issues/1794>`_.
Scripted commit, idempotent to running:
```
python3 tools/stringmangle.py --unwrap `git ls-files | egrep '\.[ch]$'`
```
Signed-off-by: David Lamparter <equinox@diac24.net>
This is the bulk part extracted from "bgpd: Convert from `struct
bgp_node` to `struct bgp_dest`". It should not result in any functional
change.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
When a peer is bound to a peer-group, the GR flags set on the
peer are over-written.
Update the GR flags for the peer after it has been bound to a
peer-group.
Signed-off-by: NaveenThanikachalam <nthanikachal@vmware.com>
There can be cases where evpn traffic is not meshed across various
endpoints, but sent to a central pe. For this situation, remove the
nexthop unchanged default behaviour for bgp evpn. Also add route
reflector commands to bgp evpn node.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Problem reported that in many circumstances, RAs created in the
process of bringing up numbered IPv6 peers with extended-nexthop
capability enabled (for ipv4 over ipv6) were not stopped on the
interface when those peers were deleted. Found several circumstances
where this occurred and fix them in this patch.
Ticket: CM-26875
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Some competitive vendors like Cisco, Bird, OpenBGPD,
Nokia already have this by default enabled.
The list is here: https://github.com/bgp/RFC8212
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
This macro is undefined if vnc is disabled, and while it defaults to 0,
this is still wrong and causes issues with -Werror
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
Support configurable options to control how link bandwidth is handled
by the receiver. The default behavior is to automatically honor the
link bandwidths received and use it to perform a weighted ECMP BUT only
if all paths in the multipath have associated link bandwidth; if one or
more paths do not have link bandwidth, normal ECMP is performed among
the multipaths. This behavior is as recommended by
https://tools.ietf.org/html/draft-ietf-idr-link-bandwidth.
The additional options available are to (a) completely ignore any link
bandwidth (i.e., weighted ECMP is effectively disabled), (b) skip paths
in the multipath which do not have link bandwidth and perform weighted
ECMP among the other paths (if at least some paths have the bandwidth)
or (c) use a default weight (value chosen is 1) for the paths which
do not have link bandwidth.
The command syntax is
bgp bestpath bandwidth <ignore|skip-missing|default-weight-for-missing>
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Implement the code to handle the other route-map options to generate
the link bandwidth, namely, to use the cumulative bandwidth or to
base this on the number of multipaths. In the latter case, a reference
bandwidth is internally chosen - the implementation uses a value of
1 Gbps.
These additional options mean that the prefix may need to be advertised
if there is a link bandwidth change, which is a new criteria. Define a
new path (change) flag to support this and implement the advertisement.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
https://lists.frrouting.org/pipermail/frog/2020-March/000776.html
It was pointed out that we are not properly passing the nexthop
through and instead we were replacing the nexthop as a Route Server
with our own.
https://tools.ietf.org/html/rfc4456#section-4
10. Implementation Considerations
Care should be taken to make sure that none of the BGP path
attributes defined above can be modified through configuration when
exchanging internal routing information between RRs and Clients and
Non-Clients. Their modification could potentially result in routing
loops.
In addition, when a RR reflects a route, it SHOULD NOT modify the
following path attributes: NEXT_HOP, AS_PATH, LOCAL_PREF, and MED.
Their modification could potentially result in routing loops.
Modify the code such that when FRR is instructed to act as a
Route-Server to pass through the nexthop.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Some were converted to bool, where true/false status is needed.
Converted to void only those, where the return status was only false or true.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Ensure that the late registration for NHT done for IPv4 route exchange
over IPv6 GUA peering is not attempted for peer-groups, only for peers.
Fixes: "bgpd: Late registration of Extended Nexthop"
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Track the returned peer_sorted value and use it where
we can and recalculate where necessary.
This is an effort to reduce the amount of work done here.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The act of peer_sort() being called always set this value
even when we are just looking it up. We need to seperate
out the idea of lookup from set.
For those places that this is immediately obvious that
this is a lookup switch over to using this function.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
