In BGP, when an interface event is detected or triggered,
the BNC that have a next-hop that matches the interface
are not evaluated.
The paths attached to the bnc context are evaluated in the
following situation:
- In the up event case, if at least one next-hop interface
matched the event interface.
- In the down event case, if there is no alternate next-hop
that does not use the event interface.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This commit changes the 'ifindex' name of the bnc structure.
As it is used only to handle ipv6 link local addresses, let
us use the 'ifindex_ipv6_ll' naming to avoid any confusions
with the ifindex value of the resolved next-hops of the bnc
structure.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Currently, "on-match (next|goto)" only works if already present in a
route-map entry when the route-map is applied to the routes. However, if
the command is added to an existing route-map entry, the route-map is
not reapplied to the routes in order to accommodate the changes. And
service restart is needed. The problem is that setting the command
doesn't signal about the change to the listener (i.e. to a routing
daemon).
With this fix, signal to the listener about addition of "on-match
(next|goto)" to a route-map entry.
Signed-off-by: Alexander Chernavin <achernavin@netgate.com>
`bnc->ifindex` should not be with 0 ( IFINDEX_INTERNAL ), so we can ignore
the wrong interface to make it safe.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Currently the vrf change procedure for the deleted interface is after
its deletion, it causes problem for upper daemons.
Here is the problem of `bgp`:
After deletion of one **irrelevant** interface in the same vrf, its
`ifindex` is set to 0. And then, the vrf change procedure will send
"ZEBRA_INTERFACE_DOWN" to `bgpd`.
Normally, `bgp_nht_ifp_table_handle()` should igore this message for
no correlation. However, it wrongly matched `ifindex` of 0, and removed
the related routes for the down `bnc`.
Adjust the location of the vrf change procedure to fix this issue.
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Make the ospf6_lsa_unlock take the same parameters
that the ospf_lsa_unlock does to make it consistent
and to also ensure that no-one can make the mistake
of getting the pointer cleared up.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Test BMP messages logging.
Configure the BMP monitoring policy, add and withdraw IPv4/v6 prefixes.
Check if the received messages coincide with the monitored router BGP
session activity.
Signed-off-by: Farid Mihoub <farid.mihoub@6wind.com>
When unconfiguring 'no import <table>', a static route imported
from a routing table number is never deleted.
When importing a route from a given table, a default distance of
15 is applied. At the time of deletion, when trying to compare
the original route with the new one, the distance does not match,
because the static route applies a default distance of 1.
If the imported route has the distance set, unset the distance
flag to avoid comparing it.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The 'redistribute table' command does not create the internal
contexts with the appropriate table identifier.
Redistributed prefixes in IS-IS do not care about the
table identifier. Add a linked list of redistribution
contexts, and map the nb configuration to the linked list.
- A new 'table' attribute is added in the 'struct
isis_redist' context.
- The 'isis_redist_update_zebra_subscriptions()' function
is removed and is replaced by direct call to zebra API
for turning on/off redirection.
- The redistributed routes coming from zebra import the
'tableid' information.
- The fabricd redistribute running-config is reworked,
and the 'get_redist_settings()' function is removed.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The yang model does not handle the table identifier in IS-IS.
For each redistributed each address family, a new list of
table elements is added to store the table identifier to
redistribute, and also the optional metric and route-map values
for each table identifier.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
The default vrf is generally non-NULL, except when shutdown. So, most
of the time it is not necessary to check if it is NULL, we should
remove the useless checks for it.
Searched them with exact match:
```
grep -rI "zebra_vrf_lookup_by_id(VRF_DEFAULT)" | wc -l
31
```
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Adjust one debug info, separate the ip address from it. Just like it is processed
in `redistribute_update()`.
Before:
```
34:1375.75.75.75/32: Redist del: re 0x55c1112067e0 (0:static), new re 0x55c1112de7c0 (0:static)
```
After:
```
(34:13):75.75.75.75/32: Redist del: re 0x55c1112067e0 (0:static), new re 0x55c1112de7c0 (0:static)
```
Signed-off-by: anlan_cs <vic.lan@pica8.com>
Add a test-case to the NHRP test that installs routes over the
NHRP tunnel endpoint routes. This confirms that zebra will use
NHRP routes when validating incoming routes from other daemons
(sharpd in this test).
Signed-off-by: Mark Stapp <mjs@labn.net>
Add a config option so that sharpd can install routes without
the ALLOW_RECURSION flag, matching IGP behavior.
The default remains 'recursion'.
Signed-off-by: Mark Stapp <mjs@labn.net>
Treat NHRP-installed routes as valid, as if they were
CONNECTED routes, when checking candidate routes'
nexthops for validity. This allows use of NHRP by an
IGP, for example, that doesn't normally want recursive
nexthop resolution.
Signed-off-by: Mark Stapp <mjs@labn.net>
bgp_zebra_tm_connect calls bgp_zebra_get_table_range which
just used the global zclient. Which of course still had
us exposing the global zclient to read and drop important
data from zebra. This fixes commit 787c61e03c
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
