In symmetric routing case for evpn (type-2/type-5)
routes, nexthop and Router mac fields can change from
the originating VTEP.
At the receiving VTEP, bgp path info may points to different
nexthop IP (nh1->nh2) and Remote MAC remain the same.
When the bgp sync the route with nexthop and RMAC fields.
For the exisitng rmac entry update/replace with the new
nexthop (VTEP) IP in remote rmac db in Zebra.
Similarly, bgp path info may points different Router-mac
(RMAC1->RMAC2) and the nexthop value remains the same.
In this case, update to the new RMAC value for the
existing remote nexthop in the Zebra' nexthop cache db.
Ticket:CM-26917
Reviewed By:CCR-9435
Testing Done:
Signed-off-by: Chirag Shah <chirag@cumulusnetworks.com>
Recently had a case where I was attempting to debug a nexthop tracking
issue across multiple bgp vrf's and since the setup vrf's in it with
overlapping address ranges, it became real fun real fast to track
vrf data associated. Add a bit of code to allow us to figure out
what vrf we are in when we print out debug messages.
Look through the rest of the code and find debugs where we are
not using bgp->name_pretty and switch it over.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Prevent IPv6 Link-local address being forward to IBGP peer,
which are not directly connected.
R1----IPV6-unnumbered-EBGP-------R2-----IPV6-IBGP-----R3
Configure route-map to set preferred global address on and apply
route-map-IN on R2 for R1-R2 session. Now check on R3's BGP and
RIB table has route nexthop as R1 link-local address, which is
not correct.
As of now we clear link-local address info from mp_nexthop_global,
only if mp_nexthop_global is populated with link-local address.
We should do it even if route-map is configured boz forwarding
link-local address from one link scope to another is violation of
the standards.
Signed-off-by: Biswajit Sadhu sadhub@vmware.com
This commit make bgpd to skip and ignore unsupported
sub-type of PREFIX_SID. (especially new defined sub-type)
Current bgpd can't parase unsupported sub-type of PREFIX_SID.
PREFIX_SID is drafted on draft-ietf-idr-bgp-prefix-sid-27.
There are already new sub-type drafted on
draft-dawra-idr-srv6-vpn-05. (Type5,6 is new defined.)
This commit fix the problem reported as #5277 on GitBub.
Signed-off-by: Hiroki Shirokura <slank.dev@gmail.com>
The final test case of this topotest wasn't really testing
anything. Do the following changes to fix this:
* Remove "no link-detect" from the zebra configs so that link down
failures are detected immediately;
* After shutting down the interface between r1 and r2, wait five
seconds before testing if the pseudowires reconverged through
the r3 router.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This is necessary to make some tests work correctly. Only topologies
created using the topogen framework benefit from this change.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When adding an OIF to the OIL, if we are not the DR
there is no need to install it then remove it.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Always bind the created sockets to their respective VRF devices. With
this it should be possible to run BFD on VRFs without needing to weaken
the security setting `net.ipv4.udp_l3mdev_accept=1`.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Some authors are added in the "GPL-2+" section, notably Alexandre
Cassen for the code in `vrrpd/`, and Cumulus Networks and Open Source
Routing which were uncredited despite many occurrence in the headers.
Signed-off-by: Vincent Bernat <vincent@bernat.ch>
We were creating `other` tables in rib_del(), vty commands, and
dataplane return callback via the zebra_vrf_table_with_table_id()
API.
Seperate the API into only a lookup, never create
and added another with `get` in the name (following the standard
we use in other table APIs).
Then changed the rib_del(), rib_find_rn_from_ctx(), and show route
summary vty command to use the lookup API instead.
This was found via a crash where two different vrfs though they owned
the table. On delete, one free'd all the nodes, and then the other tried
to use them. It required specific timing of a VRF existing, going away,
and coming back again to cause the crash.
=23464== Invalid read of size 8
==23464== at 0x179EA4: rib_dest_from_rnode (rib.h:433)
==23464== by 0x17ACB1: zebra_vrf_delete (zebra_vrf.c:253)
==23464== by 0x48F3D45: vrf_delete (vrf.c:243)
==23464== by 0x48F4468: vrf_terminate (vrf.c:532)
==23464== by 0x13D8C5: sigint (main.c:172)
==23464== by 0x48DD25C: quagga_sigevent_process (sigevent.c:105)
==23464== by 0x48F0502: thread_fetch (thread.c:1417)
==23464== by 0x48AC82B: frr_run (libfrr.c:1023)
==23464== by 0x13DD02: main (main.c:483)
==23464== Address 0x5152788 is 104 bytes inside a block of size 112 free'd
==23464== at 0x48369AB: free (in /usr/lib/x86_64-linux-gnu/valgrind/vgpreload_memcheck-amd64-linux.so)
==23464== by 0x48B25B8: qfree (memory.c:129)
==23464== by 0x48EA335: route_node_destroy (table.c:500)
==23464== by 0x48E967F: route_node_free (table.c:90)
==23464== by 0x48E9742: route_table_free (table.c:124)
==23464== by 0x48E9599: route_table_finish (table.c:60)
==23464== by 0x170CEA: zebra_router_free_table (zebra_router.c:165)
==23464== by 0x170DB4: zebra_router_release_table (zebra_router.c:188)
==23464== by 0x17AAD2: zebra_vrf_disable (zebra_vrf.c:222)
==23464== by 0x48F3F0C: vrf_disable (vrf.c:313)
==23464== by 0x48F3CCF: vrf_delete (vrf.c:223)
==23464== by 0x48F4468: vrf_terminate (vrf.c:532)
==23464== Block was alloc'd at
==23464== at 0x4837B65: calloc (in /usr/lib/x86_64-linux-gnu/valgrind/vgpreload_memcheck-amd64-linux.so)
==23464== by 0x48B24A2: qcalloc (memory.c:110)
==23464== by 0x48EA2FE: route_node_create (table.c:488)
==23464== by 0x48E95C7: route_node_new (table.c:66)
==23464== by 0x48E95E5: route_node_set (table.c:75)
==23464== by 0x48E9EA9: route_node_get (table.c:326)
==23464== by 0x48E1EDB: srcdest_rnode_get (srcdest_table.c:244)
==23464== by 0x16EA4B: rib_add_multipath (zebra_rib.c:2730)
==23464== by 0x1A5310: zread_route_add (zapi_msg.c:1592)
==23464== by 0x1A7B8E: zserv_handle_commands (zapi_msg.c:2579)
==23464== by 0x19D689: zserv_process_messages (zserv.c:523)
==23464== by 0x48F09F8: thread_call (thread.c:1599)
Signed-off-by: Stephen Worley <sworley@cumulusnetworks.com>
We have a zlog_warn that is unguarded ( and really is a debug message )
as that there is nothing the end user can do and nothing to note
here other than a debug message to track refcounts. Change
to an appropriate debug and zlog_debug it instead.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
As per weekly meeting this is an attempt to document about
how we as a community will work together on development
branches.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Add a dataplane plugin module as a sample or reference for
folks who might like to integrate with the zebra dataplane
subsystem. This isn't part of the FRR build or product; there
are some simple build and load-at-runtime instructions in
comments in the file.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
This allows to set motd from an input instead of creating a file.
Example:
root@exit2-debian-9:~/frr# telnet 127.0.0.1 2605
Trying 127.0.0.1...
Connected to 127.0.0.1.
Escape character is '^]'.
Hello, this is bgpd
User Access Verification
Password:
exit2-debian-9> enable
exit2-debian-9# sh run
Current configuration:
!
frr version 7.3-dev-MyOwnFRRVersion
frr defaults traditional
!
hostname exit2-debian-9
password belekas
log file /var/log/frr/labas.log
log syslog informational
banner motd line Hello, this is bgpd
!
!
!
line vty
!
end
exit2-debian-9#
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Root Cause:
Lookup for the point-to-point neighbor was failing because the neighbor
lookup was based on neighbor interface IP address. But, for point-to-point
neighbor the key is router-id for lookup. Lookup failure was causing the
BFD updates from PTM to get dropped.
Fix:
Added walk of the neighbor list if the network type is point-to-point to
find the appropriate neighbor. The match is based on source IP address of
the neighbor since that’s the address registered with BFD for monitoring.
Ticket: CM-20411
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
debian-9# show ip route 192.168.255.2/32 longer-prefixes
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route, q - queued route, r - rejected route
B>* 192.168.255.2/32 [20/0] via 192.168.0.1, eth1, 00:15:22
debian-9# conf
debian-9(config)# router bgp 100
debian-9(config-router)# address-family ipv4
debian-9(config-router-af)# distance bgp 123 123 123
debian-9(config-router-af)# do show ip route 192.168.255.2/32 longer-prefixes
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route, q - queued route, r - rejected route
B>* 192.168.255.2/32 [123/0] via 192.168.0.1, eth1, 00:00:09
debian-9(config-router-af)# no distance bgp
debian-9(config-router-af)# do show ip route 192.168.255.2/32 longer-prefixes
Codes: K - kernel route, C - connected, S - static, R - RIP,
O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
F - PBR, f - OpenFabric,
> - selected route, * - FIB route, q - queued route, r - rejected route
B>* 192.168.255.2/32 [20/0] via 192.168.0.1, eth1, 00:00:02
debian-9(config-router-af)#
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
Add a new '-s' option which controls whether the generated northbound
callbacks are declared with the 'static' specifier or not. If not
(the default), a prototype is generated for each callback before
their declarations.
It's suggested that daemons shouldn't use the '-s' option so that
their northbound callbacks can be implemented in different files
according to their class (config, state, rpc or notification).
libfrr commands, on the other hand, can use the '-s' option when
their associated YANG module is too small and putting all callbacks
in the same file is desirable.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
