Abstract the mac neigh installation for 169.254.0.1 into
it's own function that we can pass the mac address into.
This will allow a future commit to use this functionality
when we have the appropriate mac address from reading
optional attributes of a RA packet.
Signed-off-by: Donald Sharp <sharpd@cumuusnetworks.com>
The block comments from a couple commits were not following
proper style. Fix.
Fix SA warning that had snuck in.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Netdevices are not sorted in any fashion by the kernel during the initial
interface nldump. So you can get an upper device (such as an SVI) before
its corresponding lower device (bridge).
To fix this problem we skip resolving link dependencies during handling of
nldump notifications. Resolving instead at the end (when all the devices
are present)
Signed-off-by: Anuradha Karuppiah <anuradhak@cumulusnetworks.com>
Ticket: CM-22388, CM-21796
Reviewed By: CCR-7845
Testing Done:
1. verified on a setup with missing linkages
2. automation - evpn-min
This crash occurs only with netns implementation.
vrf meaning is different regarging its implementation (netns or
vrf-lite)
- With vrf-lite implementation vrf is a property of the interface that
can be changed as the speed or the state (iproute2 command: "ip link
set dev IF_NAME master VRF_NAME"). All interfaces of the system are in
the same netns and so interface name is unique.
- With netns implementation vrf is a characteristic of the interface
that CANNOT be changed: it is the id of the netns where the interface
is located. To change the vrf of an interface (iproute2 command to
move an interface "ip netns exec VRF_NAME1 ip link set dev IF_NAME
netns VRF_NAME2") the interface is deleted from the old vrf and
created in the new vrf.
Interface name is not unique, the same name can be present in the
different netns (typically the lo interface) and search of interface
must be done by the tuple (interface name, netns id).
Current tests on the vrf implementation (vrf-lite or netns) are not
sufficient. In some cases (for example when an interface is moved from
a vrf X to the default vrf and then move back to VRF X) we can have a
corruption message and then a crash of zebra.
To avoid this corruption test on the vrf implementation, needed when an
interface changes, has been rewritten:
- For all interface changes except deletion the if_get_by_name function,
that checks if an interface exists and creates or updates it if
needed, is changed:
* The vrf-lite implementation is unchanged: search of the interface
is based only on the name and update the vrf-id if needed.
* The netns implementation search of the interface is based on the
(name, vrf-id) tuple and interface is created if not found, the
vrf-id is never updated.
- deletion of an interface (reception of a RTM_DELLINK netlink message):
* The vrf-lite implementation is unchanged: the interface
information are cleared and the interface is moved to the default
vrf if it does not belong to (to allow vrf deletion)
* The netns implementation is changed: only the interface
information are cleared and the interface stays in its vrf to
avoid conflict with interface with the same name in the default
vrf.
This implementation reverts (partially or totally):
commit 393ec5424e ("zebra: fix missing node attribute set in ifp")
commit e9e9b1150f ("lib: create interface even if name is the same")
commit 9373219c67 ("zebra: improve logs when replacing interface to an
other netns")
Fixes: b53686c52a ("zebra: delete interface that disappeared")
Signed-off-by: Thibaut Collet <thibaut.collet@6wind.com>
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
when interface is a virtual ethernet interface, then there is no need to
update link pointer of interface.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This function is changed so that the interface index is searched across
the correct namespace.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
This is the start of separating out the static
handling code from zebra -> staticd. This will
help simplify the zebra code and isolate static
route handling to it's own code base.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
When I did a show ip route with `json` on a vrf when it didn't exist,
frr would output invalid json.
Signed-off-by: Nathan Van Gheem <nathan@cumulusnetworks.com>
Problem reported that if the vrf device is taken down and then brought
back up, any static route referencing that vrf device was not
re-installed. This fix runs back thru the static routes that
reference the vrf device coming up and re-install them.
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
When zebra starts up it receives from the kernel a full dump of
interface information. Unfortunately it is in no particular order.
As such we sometimes receive data from the kernel about interfaces
we do not know about yet.
In this bug, we are attempting to use the interface pointer(->link)
for a vlan interface that we have not properly resolved.
This fix ensures that we will not attempt to call zvni_map_svi
if we have a NULL pointer. There are other places in the code
we are already checking for the fact that the ->link pointer
is valid before calling this function, so I believe that this
is correct.
We do need to come back and resolve all ->link pointers
after we have received the full table. This can be
done in another commit.
Ticket: CM-17041
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
There are cases when switching from one netns to an other one, where the
if_table registration by index has not been flushed. This fix mitigates
the potential crashes, in case the ifp->node pointer is null, the value
is overwritten by the route_node obtained.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Notice when someone deletes a neighbor entry we've put in for
rfc-5549 gets deleted by some evil evil person. When this happens
notice and push it back in, immediately.
Ticket: CM-18612
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The following types are nonstandard:
- u_char
- u_short
- u_int
- u_long
- u_int8_t
- u_int16_t
- u_int32_t
Replace them with the C99 standard types:
- uint8_t
- unsigned short
- unsigned int
- unsigned long
- uint8_t
- uint16_t
- uint32_t
Signed-off-by: Quentin Young <qlyoung@cumulusnetworks.com>
When moving interfaces to an other place, like other netns, the
remaining interface is still present, with inactive status.
Now, that interface is deleted from the list, if the interface appears
on an other netns. If not, the interface is kept.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Because vrf with netns backend may be used, the correct zns must be
found prior any modifications.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
So as to get the correct NETNS where some discovery must be done and
populated, the zns pointer is directly retrieved from zvrf, instead of
checking that the VRF is a backend NETNS or not.
In the case where the interfaces are discovered before the VRF is enabled
( VRF-lite populate), then the default NS is retrieved.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
this is a static analysis performed by c-lang scan-build tool that
demonstrated this issue. This commit is handling the fix.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Upon following calls: interface poll, address poll, route poll, and
ICMPv6 handling, each new Namespace is being parsed. For that, the
socket operations need to switch from one NS to one other, to get the
necessary information.
As of now, there is a crash when dumping interfaces, through show
running-config.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
During VRF change handling, the connected route for the interface should be
installed only if the interface is up. Otherwise, we end up with duplicate
connected routes which can lead to other problems.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-19364
Reviewed By: CCR-7099
Testing Done: Manual verification
There are certain interfaces that when brought up and we receive
the netlink notification about it, the speed of the interface is
not set correctly. This creates a one-shot thread that will
wait 15 seconds and then requery the speed and if it is different
it will renotify the running daemons.
The kernel should notify us on speed changes, unfortunately this
is not done currently via a netlink message as you would think.
As I understand it there is some in-fighting about the proper
way to approach this issue and due to the way the kernel release
cycle works we are a ways off from getting this fixed. This
is a `hack` to make us work correctly while we wait for the
true answer.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
It is technically possible to attempt to use a NULL pointer.
Remove this from happening.
Additionally cleanup code indentation a small bit.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This improves code readability and also future-proofs our codebase
against new changes in the data structure used to store interfaces.
The FOR_ALL_INTERFACES_ADDRESSES macro was also moved to lib/ but
for now only babeld is using it.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Performance tests showed that, when running on a system with a large
number of interfaces, some daemons would spend a considerable amount
of time in the if_lookup_by_index() function. Introduce a new rb-tree
to solve this problem.
With this change, we need to use the if_set_index() function whenever
we want to change the ifindex of an interface. This is necessary to
ensure that the 'ifaces_by_index' rb-tree is updated accordingly. The
return value of all insert/remove operations in the interface rb-trees
is checked to ensure that an error is logged if a corruption is
detected.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This is an important optimization for users running FRR on systems with
a large number of interfaces (e.g. thousands of tunnels). Red-black
trees scale much better than sorted linked-lists and also store the
elements in an ordered way (contrary to hash tables).
This is a big patch but the interesting bits are all in lib/if.[ch].
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
list_free is occassionally being used to delete the
list and accidently not deleting all the nodes.
We keep running across this usage pattern. Let's
remove the temptation and only allow list_delete
to handle list deletion.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Convert the list_delete(struct list *) function to use
struct list **. This is to allow the list pointer to be nulled.
I keep running into uses of this list_delete function where we
forget to set the returned pointer to NULL and attempt to use
it and then experience a crash, usually after the developer
has long since left the building.
Let's make the api explicit in it setting the list pointer
to null.
Cynical Prediction: This code will expose a attempt
to use the NULL'ed list pointer in some obscure bit
of code.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This fixes the broken indentation of several foreach loops throughout
the code.
From clang's documentation[1]:
ForEachMacros: A vector of macros that should be interpreted as foreach
loops instead of as function calls.
[1] http://clang.llvm.org/docs/ClangFormatStyleOptions.html
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
The connected_down_ipv[4|6] functions are basically identical.
Refactor into one common interface.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The connected_up_ipv[4|6] functions were almost identical.
Combine the forces for the goodness of mankind
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Using the previously-added vty_frame() support, this gets rid of all the
pointless empty "interface XYZ" blocks that get added for any interface
that shows up in the system (e.g. dummys, tunnels, etc.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
meh. forgot to even look at the interface deletion path. this doesn't
really work well when looking for the local address in the subnet list
which has the connected prefix in it... loop ensues.
fix by using the connected prefix when looking at the list of connected
prefixes. duh.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
add a connected_check_ptp function which does the same as
connected_check, but takes an additional peer prefix argument.
also fix related prefixlen mixup in PtP addresses (the local part of a
PtP address always is /32, but previously the peer mask got copied.)
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Frr has an assumption that when interface A links to B,
we already know about B. But that might be true always.
It is probably purely depends on the configuration
and how the interfaces are hashed in Kernel.
FRR seems to sometimes get "A is linked to B" before it knows about B,
in that case, the linkage between the data structure for A & B won't be proper.
Ticket: CM-17679
Review: ccr-6628
Testing: Manual
Signed-off-by: Mitesh Kanjariya <mitesh@cumulusnetworks.com>
This allows modules to register their own additional hooks on interface
creation/deletion.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This was incorrectly implemented to begin with (it only re-added routes,
but didn't remove them) and is now covered in static_ifindex_update.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Whenever an interface is created or deleted in the system, we need to
check whether we have static routes referencing that interface by name.
If so, we need to [un]install these routes.
This has the unfortunate side effect of making static routes with
non-existent interfaces disappear from "show ip route", but I think
that's acceptable (and I don't see a "good" fix for that).
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This reverts commit c14777c6bf.
clang 5 is not widely available enough for people to indent with. This
is particularly problematic when rebasing/adjusting branches.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Daniel Walton <dwalton@cumulusnetworks.com>
This allows frr-reload.py (or anything else that scripts via vtysh)
to know if the vtysh command worked or hit an error.
Implement handling of MACs and Neighbors (ARP/ND entries) in zebra:
- MAC and Neighbor database handlers
- Read MACs and Neighbors from the kernel, when needed and create
entries in zebra's MAC and Neighbor databases.
- Handle add/update/delete notifications from the kernel for MACs and
Neighbors and update zebra's database appropriately
- Inform locally learnt MACs and Neighbors to client
- Handle MACIP add/delete from client and install appriporiate entries
into the kernel
- Since Neighbor entries will be installed on an SVI, implement the
needed mappings
NOTE: kernel interface is only implemented for Linux/netlink
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Implement fundamental handling for VNIs and VTEPs:
- Handle EVPN enable/disable by client (advertise-all-vni)
- Create/update/delete VNIs based on VxLAN interface events and inform
client
- Handle VTEP add/delete from client and install into kernel
- New debug command for VxLAN/EVPN
- kernel interface (Linux/netlink only)
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Define interface types of interest and recognize the types. Store layer-2
information (VLAN Id, VNI etc.) for interfaces, process bridge interfaces
and map bridge members to bridge. Display all the additional information
to user (through "show interface").
Note: Only implemented for the netlink interface.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
The if_update function was taking the interface name as
input and reapplying it, using strncpy to reapply the name.
This has several issues. strncpy should not be used
to copy memory in place. The second issue is that
the interface name is not actually changing when we
update interface to be in the new vrf.
Since every usage of if_update was just reapplying the same
name the interface actually had, just remove that part of
the function and rename it to if_update_to_new_vrf
to represent what it is actually doing.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Encountered a crash in zebra due to getting a delete on an SVI with
VRR configured. Since we don't actually do a delete but flag the interface
as inactive, slag VRR interfaces would remain on the vrf_iflist with a lock
count of zero, causing the crash. Since all other interface types are moved
to the default table before deleting, doing the same thing for any interfaces
that were left in the vrf.
Testing includes manual testing, bgp-min, ospf-min, vrf-min, bgp-smoke, and ospf-smoke.
All passed (first time or on rerun) or match known failures.
Ticket: CM-13288
Signed-off-by: Don Slice
Reviewed-by: Donald Sharp
The FSF's address changed, and we had a mixture of comment styles for
the GPL file header. (The style with * at the beginning won out with
580 to 141 in existing files.)
Note: I've intentionally left intact other "variations" of the copyright
header, e.g. whether it says "Zebra", "Quagga", "FRR", or nothing.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Restore the original logic in netlink_link_change() which works like this:
* once an interface event is detected, lookup the associated interface
by its name;
* call the set_ifindex() function;
* set_ifindex() will lookup the interface again but now by its ifindex. If
the lookups by name and ifindex yield to different results, then the
interface was renamed and set_ifindex() will take care of that.
In the future, zns->if_table will be split into two different data
structures to allow faster lookups by both name and ifindex.
Fixes Issue #397.
Regression introduced by commit 12f6fb9.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Add missing bits to properly unlink interface in the if_unlink_per_ns()
function.
In the long term we should convert if_table to use a more convenient
data structure like a red-black tree instead of a routing table.
Fixes issue #398.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Problem reported that crash occurred when stopping quagga in certain
circumstances. Determined that this was due to a stale pointer on the
ifp for a deleted interface. The ifp->node had been freed but the ifp
still kept a pointer to it, and when later the process was stopped, it
attempted to delete it again.
Ticket: CM-15550
Signed-off-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
These have copies in vtysh that do the node-switch locally and are
listed in extract.pl's ignore list. The ignore list however is
redundant since DEFUN_NOSH does the same thing...
ldpd is a bit hacky, but Renato is reworking this anyway.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
* lib/if.h: Remove LP_TE as Link Parameters is set if different from 0
See IS_LINK_PARAMS_SET macro and use LP_TE_METRIC to determine if TE metric
is set or not
* lib/if.c: replace LP_TE by LP_TE_METRIC in default LP status
* zebra/interface.c: replace LP_TE by LP_TE_METRIC and check if TE metric
is equal to standard metric or not
* ospfd/ospf_te.c: replace LP_TE by LP_TE_METRIC
* isisd/isis_te.c: replace LP_TE by LP_TE_METRIC
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
These now generate warnings which will break the build with -Werror.
Note this may have enabled commands that should be disabled, or the
other way around...
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This contains bgp memory leak fixes as well as cleanups to VRF/namespace
handling and has been run through extended testing in Cumulus' testbed:
Tested-by: Donald Sharp <sharpd@cumulusnetworks.com>
When link-params is configured it auto starts displaying
6000-02# conf t
dell-s6000-02(config)# int swp1
dell-s6000-02(config-if)# link-params
dell-s6000-02(config-link-params)# admin-grp 0x12345678
dell-s6000-02(config-link-params)# end
dell-s6000-02# show run
interface swp1
link-params
enable
metric 0 <----Remove the bw lines
max-bw 1.25e+06
max-rsv-bw 1.25e+06
unrsv-bw 0 1.25e+06
unrsv-bw 1 1.25e+06
unrsv-bw 2 1.25e+06
unrsv-bw 3 1.25e+06
unrsv-bw 4 1.25e+06
unrsv-bw 5 1.25e+06
unrsv-bw 6 1.25e+06
unrsv-bw 7 1.25e+06
admin-grp 305419896
exit-link-params
!
I'd like to reduce this to:
interface enp0s3
ip igmp
ip pim sm
link-params
enable
admin-grp 0x12345678 <----- Fix this to be what we entered
exit-link-params
!
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This moves all install_element calls into the file where the DEFUNs are
located. This fixes several small related bugs:
- ospf6d wasn't installing a "no interface FOO" command
- zebra had a useless copy of "interface FOO"
- pimd's copy of "interface FOO" was not setting qobj_index, which means
"description LINE" commands would fail with an error
The next commit will do the actual act of making "foo_cmd" static.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Only connected routes which have ZEBRA_IFC_REAL set should
be redistributed.
Signed-off-by: Christian Franke <nobody@nowhere.ws>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Since VRFs can be searched by vrf_id or name, make this explicit in the
helper functions.
s/vrf_lookup/vrf_lookup_by_id/
s/zebra_vrf_lookup/zebra_vrf_lookup_by_id/
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
* move netlink code from zebra_nc.c to kernel_netlink.c;
* move vrf CLI commands from if.c/interface.c to vrf.c/zebra_vrf.c;
* move declaration of the 'ns' structure to a header file.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Fix the link-params submode to use the 'exit-link-params'
to indicate we are exiting a submode.
Fixup all the relevant bits.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
If a command is put into the VIEW_NODE, it is going into the
ENABLE_NODE as well. This is especially true for show commands.
As such if a command is in both consolidate it down to VIEW_NODE.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
This puts all the proper VTY_DECLVAR_CONTEXT calls in place, removing
all vty->index uses in the process. With that, vty_config_lockless can
be enabled in zebra.
[v2: fix ordering screw-up in "interface XXX" command]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
This is a rather large mechanical commit that splits up the memory types
defined in lib/memtypes.c and distributes them into *_memory.[ch] files
in the individual daemons.
The zebra change is slightly annoying because there is no nice place to
put the #include "zebra_memory.h" statement.
bgpd, ospf6d, isisd and some tests were reusing MTYPEs defined in the
library for its own use. This is bad practice and would break when the
memtype are made static.
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Acked-by: Donald Sharp <sharpd@cumulusnetworks.com>
[CF: rebased for cmaster-next]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
NOTE: I am squashing several commits together because they
do not independently compile and we need this ability to
do any type of sane testing on the patches. Since this
series builds together I am doing this. -DBS
This new structure is the basis to get new link parameters for
Traffic Engineering from Zebra/interface layer to OSPFD and ISISD
for the support of Traffic Engineering
* lib/if.[c,h]: link parameters struture and get/set functions
* lib/command.[c,h]: creation of a new link-node
* lib/zclient.[c,h]: modification to the ZBUS message to convey the
link parameters structure
* lib/zebra.h: New ZBUS message
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add support for IEEE 754 format
* lib/stream.[c,h]: Add stream_get{f,d} and stream_put{f,d}) demux and muxers to
safely convert between big-endian IEEE-754 single and double binary
format, as used in IETF RFCs, and C99. Implementation depends on host
using __STDC_IEC_559__, which should be everything we care about. Should
correctly error out otherwise.
* lib/network.[c,h]: Add ntohf and htonf converter
* lib/memtypes.c: Add new memeory type for Traffic Engineering support
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add link parameters support to Zebra
* zebra/interface.c:
- Add new link-params CLI commands
- Add new functions to set/get link parameters for interface
* zebra/redistribute.[c,h]: Add new function to propagate link parameters
to routing daemon (essentially OSPFD and ISISD) for Traffic Engineering.
* zebra/redistribute_null.c: Add new function
zebra_interface_parameters_update()
* zebra/zserv.[c,h]: Add new functions to send link parameters
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Add support of new link-params CLI to vtysh
In vtysh_config.c/vtysh_config_parse_line(), it is not possible to continue
to use the ordered version for adding line i.e. config_add_line_uniq() to print
Interface CLI commands as it completely break the new LINK_PARAMS_NODE.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Update Traffic Engineering support for OSPFD
These patches update original code to RFC3630 (OSPF-TE) and add support of
RFC5392 (Inter-AS v2) & RFC7471 (TE metric extensions) and partial support
of RFC6827 (ASON - GMPLS).
* ospfd/ospf_dump.[c,h]: Add new dump functions for Traffic Engineering
* ospfd/ospf_opaque.[c,h]: Add new TLV code points for RFC5392
* ospfd/ospf_packet.c: Update checking of OSPF_OPTION
* ospfd/ospf_vty.[c,h]: Update ospf_str2area_id
* ospfd/ospf_zebra.c: Add new function ospf_interface_link_params() to get
Link Parameters information from the interface to populate Traffic Engineering
metrics
* ospfd/ospfd.[c,h]: Update OSPF_OPTION flags (T -> MT and new DN)
* ospfd/ospf_te.[c,h]: Major modifications to update the code to new
link parameters structure and new RFCs
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
tmp
This removes the BSD specific usage of struct sockaddr_dl
hardware address. This unifies to use explict hw_addr member for
the address, and zebra specific enumeration for the link layer
type.
Additionally the zapi is updated to never send platform specific
structures over the wire, but the ll_type along with hw_addr_len
and hw_addr are now sent for all platforms.
Based on initial work by Paul Jakma.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
# Please enter the commit message for your changes. Lines starting
# with '#' will be kept; you may remove them yourself if you want to.
# An empty message aborts the commit.
#
# Author: Timo Teräs <timo.teras@iki.fi>
#
# rebase in progress; onto 9c2f85d
# You are currently editing a commit while rebasing branch 'renato' on '9c2f85d'.
#
# Changes to be committed:
# modified: isisd/isis_circuit.c
# modified: lib/if.c
# modified: lib/if.h
# modified: lib/zclient.c
# modified: zebra/interface.c
# modified: zebra/interface.h
# modified: zebra/kernel_socket.c
# modified: zebra/rt_netlink.c
# modified: zebra/rtadv.c
# modified: zebra/zserv.c
#
# Untracked files:
# "\033\033OA\033OB\033"
# 0001-bgpd-fix-build-on-Solaris.patch
# ldpd/
# redhat/ldpd.init
# redhat/ldpd.service
# tags
#
We shouldn't have platform-agnostic code (e.g. zebra/interface.c)
calling platform-specific functions (e.g. netlink_neigh_update).
This commit introduces the kernel_neigh_update() function, which then
has to be implemented by all supported platforms. Currently only Linux
implements this function, which is only used by the RTADV code.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Ticket: CM-11808
Reviewed By: CCR-4972
Testing Done: Usual stuff
link-detect is on by default, and has been so since the first release
of Cumulus Linux. So, in the light of not displaying defaults, don't
display link-detect if enabled, only if disabled.
Resolved several memory leaks caused by ifdown/ifup the vrf device or
a swp port. For bgp/zebra/ospf/ospf6, bouncing the vrf device would cause
a linked list, Interface, and route-table to get leaked. For ospf6,
bouncing the swp device also caused leaks of Connected and Prefix entries.
Ticket: CM-10841
Signed-off-by: Don Slice
Reviewed-By: Donald Sharp
Testing Done: Manual testing, bgp and ospf mins passed, smokes had fewer failures than base
Prior to this change, interface bandwidth could not be defined above 10G. With
the use of higher speed interfaces, the ability to effectively define the path
links was highly impacted. Additionally, the default auto-cost reference-bandwidth
for ospf and ospfv3 was set to 100M, which relects a much earlier time. Changed both
the range of interface bandwidth definitions and reference bandwidths to be up to
100G. Set the default interface bandwidth (if not defined) to 10G to make the ratio
continue to cause a cost of 10 as before. Manual testing as well as ospf-min and
ospf-smoke passed successfully.
Ticket: CM-10756
Signed-of-by: Don Slice
Reviewed-by: Donald Sharp
This makes code more robust, consice and readable.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit be6335d682c5ee1b6930345193eda875705fbab2)
Coverity Scan #1221454
In zebra/interface.c if_data could be null dereferenced without early
check.
Signed-off-by: Morgan Stewart <morgan@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
(cherry picked from commit c8394ace7081ef0e71f3d162067c83c2629fc088)
"format '%qu' expects type 'long long unsigned int', but argument 3 has
type '__uint64_t'"
Move to %llu, which is more standard.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit 193e78f2460a537695e34368a29fc5cd02e4e1f5)
The default for this is slated to change, so let's print the current
default value for preexisting configurations.
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
(cherry picked from commit 4c421215a0330b96d85879810558d40027a96ca6)
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
This commit fixes interface based static routes.
static routes are now stored and if an interface
comes up it finds the route and installs it.
Ticket: CM-10869
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
The show vrf and show run commands were iterating
over the vrf_list. Use the zvrf_list instead
so that we can understand the differences
between something configed -vs- created
Ticket: CM-10139
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
On enable/disable of static routes add and remove them
from the rib as appropriate.
Ticket: CM-10139
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Instead of turning on IPv6 RA on every interface as soon as it has an IPv6
address, only enable it upon configuration of BGP neighbor. When the BGP
neighbor is deleted, signal that RAs can be turned off.
To support this, introduce new message interaction between BGP and Zebra.
Also, take appropriate actions in BGP upon interface add/del since the
unnumbered neighbor could exist prior to interface creation etc.
Only unnumbered IPv6 neighbors require RA, the /30 or /31 based neighbors
don't. However, to keep the interaction simple and not have to deal with
too many dynamic conditions (e.g., address deletes or neighbor change to/from
'v6only'), RAs on the interface are triggered upon any unnumbered neighbor
configuration.
BGP-triggered RAs will cause RAs to be initiated on the interface; however,
if BGP asks that RAs be stopped (upon delete of unnumbered neighbor), RAs
will continue to be exchanged if the operator has explicitly enabled.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-10640
Reviewed By: CCR-4589
Testing Done: Various manual and automated (refer to defect)
Ticket: CM-7076
Reviewed By: CCR-4568
Testing Done:
To allow for faster convergence, modify transmission of IPv6 RA so
that on link transitions(link up, change VRF, link add etc.), we
transmit RA fast to ensure faster convergence with BGP Unnumbered.
But we don't enable Fast RA if RA interval is in msecs as we've
fixed the fast RA interval to be 1s. We retransmit RA 4 times, once
each second on link events and when RA is first enabled.
CM-10435
Issue: IBGP BFD sessions are created as multi-hop even though peer is single-hop away. This is causing an interop issue with ICOS.
Root Cause: By design all IBGP peers are registered with BFD as multi-hop.
Fix:
• Changed the default behavior of always treating IBGP BFD sessions as mult-hop. shared_network variable is used to determine whether the IBGP peer is single hop or multi-hop away. The logic for determining whether EBGP peer is single hop or multi-hop has not been changed.
• Since the default behavior has been changed, it will cause interop issues between 2.5 and 3.0 IBGP BFD sessions. A new hidden command “bfd multihop/singlehop” has been introduced to overcome the interop issues.
dell-s6000-10(config-router)# neighbor 30.0.2.6 bfd
<2-255> Detect Multiplier
<cr>
dell-s6000-10(config-router)# neighbor 30.0.2.6 bfd multihop
dell-s6000-10(config-router)# no neighbor 30.0.2.6 bfd multihop
dell-s6000-10(config-router)#
dell-s6000-10(config-router)# neighbor 30.0.2.6 bfd multihop
dell-s6000-10(config-router)# do show running-config
!
router bgp 100
neighbor igroup peer-group
neighbor igroup bfd 5 500 500
neighbor igroup bfd multihop
neighbor 30.0.2.2 remote-as 100
neighbor 30.0.2.2 peer-group igroup
neighbor 3101🔤bcad::2 remote-as 100
neighbor 3101🔤bcad::2 peer-group igroup
neighbor 30.0.2.6 remote-as 200
neighbor 30.0.2.6 bfd multihop
neighbor 3102🔤bcad::6 remote-as 200
neighbor 3102🔤bcad::6 bfd
neighbor 3102🔤bcad::6 ebgp-multihop 255
!
CM-10260
Issue: “Unable to connect to socket” message keeps getting logged when ptmd process doesn’t exist.
Root Cause: BFD clients (bgpd, ospfd and ospf6d) during initialization try to register with BFD/PTM by default. This results in continuous logging If PTM does not exist since there is no max on number of retries.
Fix:
• Stop the retries to connect to PTM after max reconnect timer of 5 mins is reached.
• Added zebra debug event wrapper to message logging to prevent it from showing by default.
CM-4541
Issue: Addition of a new command "ptm-enable" or "no ptm-enable" per interface to enable/disable PTM link status checks for an interface.
Fix: Currently there is only one ptm-enable global command that enables/disables PTM status updates for all interfaces. This new command will give the handle to individually stop interface from reacting on the PTM status updates.
• by default interface uses the ptm-enable global configuration
• "no ptm-enable" on an interface will disable PTM status updates from taking affect for that interface. This can bring the interface up if it was brought down due to PTM status update.
• "ptm-enable" on an interface will cause the interface to fallback to the global ptm-enable configuration value and will bring the interface up or down based on the last stored PTM status update if global ptm is enabled.
Ticket: CM-10435, CM-10260 and CM-4541
Signed-off-by: Radhika Mahankali
Reviewed-by: Donald Sharp, Kanna Rajagopal
Move zebra_vrf_XXX functionality into it's own
file so that we can isolate a bit the api edges
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
The struct zebra_ns was littered throughout the code
base in a half-hazard fashion. Gather up the references
and isolate the code a bit better.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
The vrf_add_update function does not need to exist.
Move it's constituent parts into the appropriate
vrf_create/vrf_enable functionality as well as
move the zebra_vrf_add_update() function call
into zebra_vrf_enable()
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
vrf_delete_update really belongs in vrf.c broken up
into it's appropriate places.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Create the idea of a VRF_UNKNOWN, this is for a vrf where we don't
yet have the vrf_id for it yet.
Refactor the vrf_create code out of existence. We had two code
paths vrf_create and vrf_get. We should use vrf_get to create
the new vrf since XXX_get() creates the data structures now.
Signed-off-by: Donald Sharp
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
ZEBRA_VRF_ACTIVE is a poor name for when a vrf is
actually active. Rename VRF_ACTIVE.
Ticket: CM-10338
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Radhika Mahankali <radhika@cumulusnetworks.com>
It is quite useful to be able to assert whether specific interfaces have
flapped or also to verify that specific interfaces have not flapped.
By having counters for those events and storing the last time of their
occurrence, this is made possible.
Signed-off-by: Christian Franke <chris@opensourcerouting.org>
Acked-by: Jafar Al-Gharaibeh <jafar@atcorp.com>
When an interface changes which vrf it is part of, it needs to be added
to the list of possible router-id choices in the new vrf and removed
from the old vrf/default.
Ticket: CM-9074
Signed-off-by: Don Slice
Reviewed-by: Vivek Venkatraman
We were incorrectly using vrf instead of zebra_vrf in a
few spots.
Ticket: CM-9412
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Implement VRF change semantics for an interface to be invoked
when an interface is moved from one VRF (e.g., the Default) to
another. This includes the message definition as well as updating,
deleting or adding the interface from clients, depending on their
interest in the VRFs (old and new). Also handle replay of the
addresses on the interface upon VRF change, if required.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Don Slice <dslice@cumulusnetworks.com>
Ticket: CM-9527
Reviewed By: CCR-4174
Testing Done: Manual tests of various scenarios
When enabling IPv6 Router Advertisements automatically based on the
presence of IPv6 address on an interface, do it only for relevant
interfaces.
Note: This needs a configure option for completion.
Ticket: CM-9358
Reviewed By: CCR-4116
Testing Done: Manual verification
Ticket: CM-9110
Reviewed By:
Testing Done: Manual testing, see ticket
Aliased "show interface name swpxx" to "show interface name swpxx vrf all" to find the interface regarless of which vrf it resides in.
Convert the rest of zebra over to use a Namespae and VRF.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Back out original null pointer fix targeted it was the wrong fix.
Basically when a ip address is deleted the RA code was waiting till after
the connected pointer was deleted to set the RA appropriately.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: Daniel Walton <dwalton@cumulusnetworks.com>
Currently, when RIB processing is initiated (i.e., by calling rib_update()),
all routes are queued for processing. This is not desirable in all situations
because, sometimes the protocol may have an alternate path. In addition,
with NHT tracking nexthops, there are situations when NHT should be kicked
off first and that can trigger subsequent RIB processing.
This patch addresses this by introducing the notion of a trigger event. This
is only for the situation when the entire RIB is walked. The current triggers
- based on when rib_update() is invoked - are "interface change" and "route-
map change". In the former case, only the relevant routes are walked and
scheduled, in the latter case, currently all routes are scheduled for
processing.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-7662
Reviewed By: CCR-3905
Note: The initial defect in this area was CM-7420. This was addressed in
2.5.4 with an interim change that only walked static routes upon interface
down. The change was considered a bit risky to do for interface up etc. Also,
this did not address scenarios like CM-7662. The current fix addresses CM-7662.
Some of the changes include:
- ensuring IPv6 addresses are printed correctly
- say 'updating' or 'deleting' etc. only when that is actually done
- say 'queuing' or 'dequeuing' only when that is actually done
- print useful info for 'detailed' debug - that now subsumes 'rib queue'
- delete various useless logs
- VRF-specific - print VRF id in RIB debugs prior to prefix
(e.g., 4:37.1.1.0/28)
Ticket: CM-8110
Reviewed By: CCR-3765
Testing Done: Manual testing (2.5-br)
This Change modifies what zebra thinks is an unnumbered interface.
If the interface is not a loopback and the prefixlength for the
interface is 32 than consider this an unnumbered interface.
Ticket: CM-8016
Reviewed by: CCR-3827
Testing: Full Regression Suites
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
The RTADV define was not being set correctly or consistently.
Make the code consistent with our HAVE_IPV6 define.
If the user wants to explicitly turn it off then they should
run --disable-rtadv from the configure cli
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
A new member "vrf_id" is added to "struct rib", reflecting the VRF
which it belongs to.
A new parameter "vrf_id" is added to the relative functions where
need, except those:
- which already have the parameter "vrf_id"; or
- which have a parameter in type of "struct rib"; or
- which have a parameter in type of "struct interface".
All incoming routes are set to default VRF.
In fact, all routes in FIB are kept in default VRF. And the logic
is not changed.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
[DL: conflicts fixed + compile warning fix]
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Conflicts:
zebra/connected.c
zebra/kernel_socket.c
zebra/rib.h
zebra/rt_netlink.c
zebra/zebra_rib.c
zebra/zserv.c
Conflicts:
zebra/connected.c
zebra/interface.c
zebra/kernel_socket.c
zebra/rib.h
zebra/rt_netlink.c
zebra/rtread_getmsg.c
zebra/zebra_rib.c
zebra/zebra_vty.c
zebra/zserv.c
The following commands only show interfaces in the default VRF:
show interface
show interface IFNAME
show interface description
New options are introduced to show interfaces in a specified VRF:
show interface vrf N
show interface IFNAME vrf N
show interface description vrf N
or all VRFs:
show interface vrf all
show interface IFNAME vrf all
show interface description vrf all
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Introduce a new command "interface IFNAME vrf N" to configure an
interface in the non-default VRF.
Till now, only zebra uses this command. Other daemons will install
the command when they support multiple VRFs.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Conflicts:
zebra/interface.c
Later, an interface will belong to a specific VRF, and the interface
initialization will be a part of the VRF initialization. So now call
if_init() from vrf_init(), and if_terminate() from vrf_terminate().
Daemons have the according changes:
- if if_init() was called or "iflist" was initialized, now call
vrf_init() instead;
- if if_terminate() was called or "iflist" was destroyed, now call
vrf_terminate() instead.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Conflicts:
bgpd/bgp_main.c
pimd/pim_iface.c
pimd/pim_iface.h
pimd/pim_main.c
pimd/pimd.c
Later, an interface will belong to a specific VRF. Now we add a
property "vrf_id" to the "struct interface", and keep it as the
default value 0.
This property is shown when displaying interfaces information.
It is also added in some logs.
This is just the preparation to move the interace list into the
"struct vrf". The main logic is not changed.
Signed-off-by: Feng Lu <lu.feng@6wind.com>
Reviewed-by: Alain Ritoux <alain.ritoux@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Vincent JARDIN <vincent.jardin@6wind.com>
Signed-off-by: David Lamparter <equinox@opensourcerouting.org>
Conflicts:
lib/if.c
zebra/interface.c
Ticket: CM-7420
Reviewed By: Vivek, Donald
Testing Done: UT, verification of the fix + ospf and bgp smoke
On a link delete/down event, schedule only the prefixes which have a
static RIB too.
Signed-off-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Reviewed-by: Donald Sharp <sharpd@cumulusnetworks.com>
Ticket: CM-6812
Reviewed By: Donald
Testing Done:
Double commit of 2119c8fccda5f1497820009c6f1f82eda3c8d0f1 from 2.5br to master
In Quagga, the ptm status is shown as pass for all the interfaces that PTM is not tracking. When ptm is enabled in Quagga all the interfaces are initialized as pass and changed to fail/pass when ptm cable check updates are received. For all the interfaces for which no status was received from PTM remain at pass status. Interface show in quagga indicates wrong status and it should be n/a for all the untracked interfaces. To fix the problem introduced a third state “unknown” and this is default ptm status for all the interfaces. The ptm status is updated accordingly to pass/fail when the updates are received from PTM. Also, reset all interface ptm status to unknown when the connection with ptm is lost and the status gets updated when the connection with PTM is re-established.
Integrates Prescriptive Topology Module(ptm) into quagga.
If this module is enabled, link ups are notified only after the link is verified
as being connected to the neighbor specified. The neighbor specification and
checking is done by the ptm daemon.
<This is a recommit of this patch because it was changed in situ>
This patch also adds BFD multihop support for BGP. Whether a peer is multi-hop or single hop is determined internally. All IGP peers are considered as multi-hop peers. EBGP peers are considered as single hop unless configured as multi-hop.
BGP BFD command enhancement to configure BFD parameters (detect multiplier, min rx and min tx).
router bgp <as-number>
neighbor <name/ip-address> bfd <detect mult> <min rx> <min tx>
Signed-off-by: Radhika Mahankali <radhika@cumulusnetworks.com>
Reviewed-by: Dinesh G Dutt <ddutt@cumulusnetworks.com>
Reviewed-by: Vipin Kumar <vipin@cumulusnetworks.com>
Reviewed-by: Kanna Rajagopal <kanna@cumulusnetworks.com>
using IPv6 Router Advertisements (RAs) must be deleted. When an
interface comes up and neighbors are learnt on that interface, the
BGP FSM for any interface peer must be started only if a valid
local address exists; the local address may come up later after IPv6
Duplicate Address Detection.
