Add support for read only mib objects from RFC4444.
Signed-off-by: Lynne Morrison <lynne@voltanet.io>
Signed-off-by: Karen Schoener <karen@voltanet.io>
1. There were few tests where routes were configured with blackhole and
non-blackhole nexthops simultaneously, enhanced tests accordingly and
verified in master branch and with PR #8158 changes.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
Problem:
Prefix-list with mulitiple rules, an update to
a rule/sequence with different prefix/prefixlen
reset prefix-list next-base pointer to avoid
having stale value.
In some case the old next-bast's reference leads
to an assert in tri (trie_install_fn ) add.
bt:
(object=0x55576a4c8a00, updptr=0x55576a4b97e0) at lib/plist.c:560
(plist=0x55576a4a1770, pentry=0x55576a4c8a00) at lib/plist.c:585
(ple=0x55576a4c8a00) at lib/plist.c:745
(args=0x7fffe04beb50) at lib/filter_nb.c:1181
Solution:
Reset prefix-list next-base pointer whenver a
sequence/rule is updated.
Ticket:CM-33109
Testing Done:
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
In prefix-list nortbound callback's validation
phase, use type as enum rather string for better
performance.
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Following patch
" lib: disallow access list duplicated values"
introduce a libyang dnode iterator for every prefix-list
config which adds an overhead of traversal all prefix dnodes
and degrades the performance in scaled prefix-list config.
This check is not necessary in prefix-list northbound callbacks
as there won't be a case where prefix-list config comes to nb
callback without sequence number.
The dup check is only necessary for the vtysh case for backward
compatiblity reason where cli can be accepted without sequence number.
Ticket: CM-32035
Reviewed By: CCR-11096
Testing Done:
Signed-off-by: Chirag Shah <chirag@nvidia.com>
Remove when statements from prefix-list yang OM,
and do the same check in frr validation phase.
This helps a bit in perfomance of prefix-lists
scale config.
Ticket:CM-32035
Reviewed By:CCR-11096
Testing Done:
Signed-off-by: Chirag Shah <chirag@nvidia.com>
If we are filtering a route due to any of the filter reasons
we should not be setting the BGP_NODE_FIB_INSTALL_FIB_PENDING
flag. This is especially evident with say a loopback that
is covered by a network statement. When we receive the route
back from our peer we should not be setting the
BGP_NODE_FIB_INSTALL_PENDING flag on it.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Add some pytest.mark.bgpd. This is about all I could stomach doing
in one patch. I'll do another pass at another time.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Instead of crashing, print "NULL" when printfrr callback for
nexthops is called for a NULL nexthop argument.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
now that sequence number is configurable, there is no problem in
permitting to configure seq 0 sequence number.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
When you use a single BGP session for both IPv4 and IPv6 it's a bit
annoying going into ipv6 address-family and explicitly activating it.
Let's get this automatically if enabled with `bgp default ipv6-unicast`.
Signed-off-by: Donatas Abraitis <donatas.abraitis@gmail.com>
When the last SID in the TI-LFA repair list is an Adj-SID from the
penultimate hop router towards the final hop, the No-PHP flag of the
original Prefix-SID must be honored in the repair list itself since
the penultimate hop router won't have a chance to process that SID
and pop it if necessary.
Reported-by: Fredi Raspall <fredi@voltanet.io>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In some cases it's possible that the TI-LFA algorithms will try to
compute a SID repair list more than once for the same backup nexthop
[1]. This of course shouldn't be allowed, as a backup nexthop can't
have multiple label stacks. When that happens, we should just ignore
the new repair list if one is already applied, instead of asserting
and crashing the daemon.
[1] One scenario this can happen is when there's ECMP involving
different P-nodes in the PQ-space intersection.
Reported-by: Fredi Raspall <fredi@voltanet.io>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
* Clarify which commands are applicable to which flavors of LFA;
* Explain the default prefix priority for different prefix types;
* Rearrange some command descriptions so that they appear in this
order: local LFA, remote LFA and then TI-LFA.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Example:
```
show yang operational-data /frr-routing:routing/control-plane-protocols/control-plane-protocol[type='frr-staticd:staticd'][name='staticd'][vrf='default'] staticd
```
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
CI constantly fails to execute "show zebra fpm stats":
```
Execute: show zebra fpm stats
Traceback (most recent call last):
File "/usr/lib/frr/generate_support_bundle.py", line 55, in executeCommand
cmd_output = subprocess.check_output(cmd_exec_str, shell=True)
File "/usr/lib/python3.6/subprocess.py", line 356, in check_output
**kwargs).stdout
File "/usr/lib/python3.6/subprocess.py", line 438, in run
output=stdout, stderr=stderr)
subprocess.CalledProcessError: Command 'vtysh -c "show zebra fpm stats" ' returned non-zero exit status 1.
```
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
We can proactively check whether this mroute will be nacked by loopfree
MFC checks so let's do it in the apply phase and emit a useful error
message.
Signed-off-by: Quentin Young <qlyoung@nvidia.com>
Add support for read-only snmp mib objects as described in RFC 3815,
excluding statistics.
Signed-off-by: Lynne Morrison <lynne@voltanet.io>
Signed-off-by: Karen Schoener <karen@voltanet.io>
