Update verify_ospf6_neighbor() so we can verify there are no
neighbors in a given router
input_dict = {
"r0": {
"ospf6": {
"neighbors": []
}
}
}
result = verify_ospf6_neighbor(tgen, topo, dut, input_dict)
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
RFC 3101 states both E-bit and N-bit need to be checked when receiving a Hello packet.
"To support the NSSA option an additional check must be made in the function
that handles the receiving of the Hello packet to verify that both the N-bit
and the E-bit found in the Hello packet's option field match the area type and
ExternalRoutingCapability of the area of the receiving interface."
This PR adds the check for the N-bit
Signed-off-by: ckishimo <carles.kishimoto@gmail.com>
RCA: When upstream transition from Joined to NotJoined due to SGRpt
prune, then only SGRpt prune was sent and SG Prune is missed.
Fix: Send SG Prune towards source as well as SGRpt prune towards RP.
Signed-off-by: sarita patra <saritap@vmware.com>
The interface area command is deprecated under
router ospf6 and should be on the individual interface.
Let's modify the tests to not actually put the
interface foo area 0.0.0.0 command under the
router node.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When using build_config_from_json there exists a timing
window where neighbors can come up before the router-id
is applied. As a precaution, quickly clear the neighbors
to ensure that we get neighbors with the expected router-id.
This can especially happen under high system load.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The test_ospf_dual_stack test had area configuration
under the `router ospf6` nodes. This is getting
lots of warning messages from the cli. Let's remove
this.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
When testers use the build_config_from_json function
the create_router_ospf function is double creating
the ospfv3 cli to be passed in. This is because
the create_router_ospf loops over both v2 and v3
and then create_router_ospf6 re-adds v3.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The ospf_basic_functionality/test_ospf_lan.py creates
a ethernet segment and attaches 4 routers to it and
assigns ip addresses in a /24. As one of the tests
it picks a new address for r0 which coincides with
a ip address on r3. Then the test immediatly
checks for other data. The problem is of course
that if a test is `slow` enough hello's will
start to be ignored from r3 to r0 and the
neighbor relationships will come down. Choose
an ip address that doesn't cause this issue.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The new bgp_route_server_client test is not setting the
timers for peers to be fast enough to have the ability
to converge in under 60 seconds if a packet is dropped/missed
at startup. Make the test have the ability to converge
under load
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
The external_id_table was only ever used to store pointers to data
and was never used for lookup during the course of normal operations.
However it did lead to crashes because somewhere along the way
external routes stored in the external_table never had their
id associated into the external_id_table and we would assert
on the node lookup failing.
Since this code was never used for anything other than
storing data and it was never retrieved for anything useful
let's just remove it from ospf6d.
Signed-off-by: Donald Sharp <sharpd@nvidia.com>
Move the "longer-prefixes" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "route-map" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "filter-list" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "prefix-list" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Move the "community-list" option from show_ip_bgp_cmd to
show_ip_bgp_json_cmd so that is has access to JSON output.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
There's no need to have different calls to bgp_show() when the only
difference is one argument that corresponds to a "void *" parameter.
Code duplication should be reduced to a minimum to avoid bugs like
the one fixed in the previous commit.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Like done in the other places (when "all" isn't used), pass the
actual alias name to bgp_show() instead of a null pointer.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
When the VRF interface is coming up, we don't need to fixup VRF ids - it
was already done in static_vrf_enable when the interface was created.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
add a parameter to resolver api that is the vrf identifier. this permits
to make resolution self to each vrf. in case vrf netns backend is used,
this is very practical, since resolution can happen on one netns, while
it is not the case in an other one.
Signed-off-by: Philippe Guibert <philippe.guibert@6wind.com>
Since f60a1188 we store a pointer to the VRF in the interface structure.
There's no need anymore to store a separate vrf_id field.
Signed-off-by: Igor Ryzhov <iryzhov@nfware.com>
