Issue number #6291 describes how OSPFd crashes after being deleted and then
added again with configuration when segment routing is used.
The problem occurs in ospf_ri.c because the OspfRI structures retains
the reference to the old area pointer which is mofified when ospfd is
reactivated by configuration. When segment routing is activated, the LSA Router
Information is sent with reference to the old area pointer, instead the new one,
which causes the crash. The same problem is also present in ospf_ext.c with
OspfEXT structure and Extended Link/Prefix structure.
This commit introduces Extended Link/Prefix and Router Information LSAs flusing
when OSPFd is stopped when configuration is removed and adds the correct
initialization to the area pointer in OspfRI and Extended Link/Prefix structure
when OSPFd is re-enabled with the configuration. Area pointer has been removed
from the OspfEXT structure as it is never used with this commit.
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Extend the next hop tracking for type-2 and type-3 EVPN routes also.
Updates: "bgpd: Add nexthop of received EVPN RT-5 for nexthop tracking"
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
When there is a NHT change and the paths dependent on that NHT are being
evaluated, skip those that are marked for removal or as history.
When a route gets withdrawn, its valid flag is cleared and it is flagged
for removal; in the case of an EVPN route, it is also unimported from
VRFs (L2 and/or L3). bgp_process is then scheduled. Under rare timing
conditions, an NHT update for the route's next hop may arrive right after,
and if routes flagged for removal are not skipped, they may not only be
incorrectly marked as valid but also re-imported in the case of EVPN,
which will be a serious error.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Ensure that only if there is a change to the path's validity based
on the NHT update, EVPN import or unimport is invoked.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Display next hop resolution information, whether the "detail" option is
specified or not as it is quite fundamental and only minimally increases
the output.
Introduce option to look at a specific NHT entry, which will also show
the paths associated with that entry.
Signed-off-by: Vivek Venkatraman <vivek@cumulusnetworks.com>
Changes:
- Renamed file so we don't get confused when it fails.
- Use `json_cmp` instead of direct key access.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The command `area ... virtual-link ... retransmit-interval` supports
1-65535 range and the documentation already said
`ip ospf retransmit-interval` supports that, lets make the DEFUN to
accept that value.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
The involved piece of code is supposed to find a 'closest' match for two
JSON structures using another JSON diff. However, it can happen that
during that new diff the JSON structures are altered (elements from a
list are deleted when 'found'). This is in general ok when the deleted
element is part of the JSON structure which 'matches', but when it later
turns out that some other element of the structure doesn't fit, then the
whole structure should be recovered. This is now realized by using a
deepcopy for the besaid new JSON diff such that the original is only
altered (e.g. deleted) when the diff is clean.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Currently zebra when you compile without router advertisements
will just say something like `cannot handle message 42`. Which
is not terribly useful to an end user.
Add some smarts to the zapi message handling to just do nothing
and output a debug if someone has it turned on.
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Allow user to pre-configure peers with a profile. If a peer is using a
profile any configuration made to the peer will take precedence over
the profile configuration.
In order to track the peer configuration we have now an extra copy of
the peer configuration in `peer_profile` inside `struct bfd_session`.
This information will help the profile functions to detect user
configurations and avoid overriding what the user configured. This is
especially important for peers created via other protocols where the
default `shutdown` state is disabled (peers created manually are
`shutdown` by default).
Profiles can be used before they exist: if no profile exists then it
will use the default configuration.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Allow sessions to use BFD profile configurations instead of having to
clone the configuration per peer.
If using a profile and setting a peer configuration, the peer
configuration will take precedence over the profile.
Signed-off-by: Rafael Zalamena <rzalamena@opensourcerouting.org>
Clean up a few lines of cli command installation; remove a
duplicate; follow the command grouping pattern better.
Signed-off-by: Mark Stapp <mjs@voltanet.io>
1. Adding 4 testcases to this testsuite to verify BGP multi-vrf functionality
2. Adding supporting JSON file to create topology and base config
3. Execution time is ~3 mins
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
1. Adding 22 testcases to this testsuite to verify BGP multi-vrf functionality
2. Adding supporting JSON file to create topology and base config
3. Execution time is ~7 mins.
Signed-off-by: Kuldeep Kashyap <kashyapk@vmware.com>
if mpls-te is enabled in the area, on creating a circuit we
must refresh the link params - else interfaces that are enabled
for IS-IS after configuring 'mpls-te on' will not correctly
advertise link parameters.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
in the CLI we state that the bandwidth of a link is
in Megabits per second, but when converting it to
Bytes per second for TE purposes we were treating
it as Kilobits. Fix the conversion error.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
