The purpose of the Attach-bit is to accomplish inter-area routing. In other
venders, the Attached-bit is automatically set when a router is configured
as a L1|L2 router and has two adjacencies. When a L1 router receives a LSP
with the Attached-bit set it is supposed to create a default route pointing
toward the neighbor to provide a default path out of the L1 area.
ISIS implementation has been fixed to support the above definition:
Setting the Attach-bit is now the default behavior and we allow the user to
turn it off.
We will only set the Default Attach-bit when creating a L1 LSP, if we are
a L1|L2 router and have a L2 adjacency up.
When a L1 router receives a LSP with the Attach-bit set, we will create a
default route pointing to the L1|L2 router as the nexthop.
The default route will be removed if the LSP is received with the Attach-bit
cleared.
Signed-off-by: Lynne Morrison <lynne@voltanet.io>
Add the "n-flag-clear" option to the "segment-routing prefix"
command. The only thing that option does is to clear the node
flag of the Prefix-SID, even if it corresponds to a local loopback
address. No changes are necessary other than that in order to fully
support Anycast-SIDs. isisd already supports multiple routers
advertising the same route with the same Prefix-SID after the recent
refactoring. Clearing the node flag for such anycast routes isn't
strictly required, but failure to do so can lead to problems like
TI-LFA picking the wrong Prefix-SID when calculating repair paths.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
1. Added isis with different vrf and it's dependecies.
2. Added new vrf leaf in yang.
3. A minor change for IF_DOWN_FROM_Z passing argrument is
replaced with ifp pointer in api "isis_if_delete_hook()".
4. Minor fix in the isisd spf unit test.
Co-authored-by: Kaushik <kaushik@niralnetworks.com>"
Signed-off-by: harios_niral <hari@niralnetworks.com>
BFD profiles can now be used on the interface level like this:
interface eth1
ip router isis 1
isis bfd
isis bfd profile default
Here the 'default' profile needs to be specified as usual in the
bfdd configuration.
Signed-off-by: GalaxyGorilla <sascha@netdef.org>
Segment Routing Local Block (SRLB) is part of RFC8667. This change introduces
the possibility for isisd to advertize SRLB in LSP. Base and Range of SRLB
could be configured through CLI or Yang.
Adjacency-SID are now using this SRLB for label allocation. SRLB could also
be used for SID-Binding (e.g. LDP to SR).
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Now that the "frr-interface" list has a "state" container, move the
IS-IS interface state nodes underneath it using a new augmentation.
Also, update the IS-IS SR topotest to account for this change. Make
use of symlinks where possible to avoid having multiple files with
the same content.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
This is an implementation of the IS-IS SR draft [1] for FRR.
The following features are supported:
* IPv4 and IPv6 Prefix-SIDs;
* IPv4 and IPv6 Adj-SIDs and LAN-Adj-SIDs;
* Index and absolute labels;
* The no-php and explicit-null Prefix-SID flags;
* Full integration with the Label Manager.
Known limitations:
* No support for Anycast-SIDs;
* No support for the SID/Label Binding TLV (required for LDP interop).
* No support for persistent Adj-SIDs;
* No support for multiple SRGBs.
[1] draft-ietf-isis-segment-routing-extensions-25
Signed-off-by: Olivier Dugeon <olivier.dugeon@orange.com>
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
In the name of consistency, these commands are very similar to the
ospfd SR configuration commands.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Most definitions were borrowed from the IETF IS-IS SR YANG module,
with a few adaptations. Of particular notice are the following:
* No support for the configuration of multiple SRGBs.
* No distinction between local and connected Prefix-SIDs, both are
configured the same way.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
Yang constraints enforced by the northbound callbacks require that
the maximum lifetime be >= than (refresh interval + 300). When we are
moving from one config to another through frr-reload.py, we issue
a number of vtysh -c commands ('no lsp-refresh-interval level-1 500',
'no max-lsp-lifetime level-1 1000'), which reset these parameters to their
default values, respectively 900 and 1200. Depending on the actual
values in the current config, the order in which these commands are sent
might be the wrong one, in that we hit an invalid intermediate state and
make vtysh (and by extension frr-reload.py) return an error.
As a workaround, let's add a one-liner command that sets all these
inter-related parameters in one go, and make isisd display them as a
single line too, so that the diff will be computed as a single command.
The old individual commands are kept to ensure backwards compatibility.
Signed-off-by: Emanuele Di Pascale <emanuele@voltanet.io>
Rearrange the isisd northbound callbacks as following:
* isis_nb.h: prototypes of all northbound callbacks.
* isis_nb.c: definition of all northbound callbacks and their
associated YANG data paths.
* isis_nb_config.c: implementation of YANG configuration nodes.
* isis_nb_state.c: implementation of YANG state nodes.
* isis_nb_notifications.c: implementation of YANG notifications.
This should help to keep to code more organized and easier to
maintain.
No behavior changes intended.
Signed-off-by: Renato Westphal <renato@opensourcerouting.org>
